Guangzhou Chuangyu Animation

Technology Co LTD

KEY MASTER
Manual

Please read the manual before using the machine !

Keep the manual in good condition !

 key master
1.BRIEF INTRODUCTION
diamond key is a new evrsion of indoor prize machine.This machine is sample to play,
with brilliant cabinet design built of high quality materials !

2.NOTICE
2-1.SAFTTY INSTRUCTIONS
This machine is only for indoor use ,si not suitable for outdoor use.

When the machine has been installed well,place the bottom of the

machine on the floor to make sure it is steady.

Do not take it apart,make it up or move it arbitrarily.

Switch off the power and pull out the plug before moving it.

Place it on even floor,not the smoothie,unsteady or seriously vibrating place.

Do not place it near any high temperature of easily sparkling equipment.

Do not place any sundries on the machine or let any heavy press the power wire.

Do not expose the circuit part in the machine to the air.

2-2.Notice for operation

Check whether the power plug and power wire are good,whether the

voltage is suitable for the machine before switching the power on.

Voltage of power supply should be accord to the voltage onthe back cover

of it.

Switch off the power before you maintain or inspect the machine.

Only qualified personnel are allowed to inspect the electric control device

of it .

Use suitable accessories to displace parts of apparatus.

Hold the plug instead of the wire to unplug the power wire .

Do not to plug or unplug the with wet hand,do not pull or twist the power wire.
 key master
3.Accessories
Check whether the follwing accessories are ready before using it:
NAME QTY REMARK
Manual 1
Keys 3
Power cord 1

4.How to play
Insert cion ,the button light is on in the control panel and a ball out,

Move the joystick to select your favorite prize,

Keep pressing the UP button move pushrod to your target,

Loose ,shaft push to prize out,

If shaft move into the hole ,the Key spin half round and pull the prize out,

Player get prize ,game over,

Prize store fixing:

Please check the prize store and shaft direction ,and fix it correct,

Adjust all the direction please reset machine for the setting valid,

It need adjust the direction once a month at least.

How to adjust prize position:

Long press the setting key to enter the setting，

Move the joystick up and down select B,Press the red

button on the console to enter B1,Press the red button

to display（Ready to start),Press the red button again，

When you see a LCD display(correction)，Machine into

automatic positioning mode，Do not open until automatic

positioning is complete。
 Program
download LEDconnector
interface

Volume knob CN11/CN12

CN13/CN14
J8 loudspeaker
J1 LED supply

J6 Main power
supply
J2 LCD

J5 Capsule

J4 Crane J3 other

J1 LED supply J2 LCD

12V GND GND 5V GND

J3 other

12V 12V 12V 12V 12V 12V GND GND GND GND GND GND GND

income expend
button JOYS JOYS JOYS JOYS but
lamp COIN COIN SET COIN
TICK TICK TICK TICK ton
 J4 Crane
key before
left and
Front spring down optical Stepper Stepper key and
location location location sensor GND GND 5V motor motor motor
right
motor
after
motor
right before
left and
back left Stepper Stepper key and
optical
location location sensor GND GND GND 5V motor motor motor
right
motor
after
motor

J5 Capsule J6 Main power

supply
location 12V 12V 12V GNDGND
location GND GND

J8 loudspeaker
5 TECHNICAL PARAMETERS

Mode:SY.SY02-1

Location requirements:

Temperature -10 ~+40 ,U.V.radiation Very low , humidity low , Vibrations level:low.

Dimension:W970*D850*H2040MM

Weight:188KG

Power supply:220V

Max : 120W

Player: 1 pc

6 SETTING
In the standby screen, long press
the setting button to enter the
setting, the rocker (front)
(back) to select, (left) (right)
to add or subtract, and press the
fetch button to determine.White
background blue is the current
selection.

Setup steps:
1. Select the entry items from the
rocker up and down
2.Press the fetch button to enter
the selected item
3.Set the corresponding value
left and right of the rocker
4.Press the fetch button to set
5.Select return and press enter
to confirm exit

* H terms are different

for different machines。
Coin per play
Just throw in a few game COINS and play it once

Game time
Time per game

Music
You can set on or off

Num. coins/bonus
You can set on or off
The number of COINS left on the machine after shutdown
and restart will be reset

Volume
The bigger the number, the louderthe voice

Switch storage
Optional to close
If I pick a number that's what thenumber is,It's how many
COINS you put in a row and you get one

Key adjust
Adjust the key's downward rotation position when winning

Motor
Adjust the speed of up and down motor，Motor speed is fastest
when the value is 79,The motor speed is the slowest when the
value is 99
C Prize setup

N times out
That is, the machine accumulates
when the game is full of this
setting raet , it may give a gift

3 6 9 12 15

2 5 8 11 14

1 4 7 10 13

D Accounts
T income:the total amount of money invested in the machine
throughout its history
T payout:The total number of gifts given out in the history
of the machine
C income:The amount of money
invested since the last closing of accounts
C payout:Gifts given since the last closing of accounts
Total plays:The last prize has been awarded to players so far

E Accounts reset
Native is to clear the accounts,The clearing content
is:C income/C payout/Total plays
F Factory reset
Try restoring factory Settings
when a failure cannot be resolve

G GSM Setting
phone sctting

Setting of phone number (the number of receiving machine

information)
Press the red button on the console to enter the number
setting
Move the rocker left and right to select number of digits, the
rocker up and down
Select number and number Settings to complete press the
red button to exit
time setting

Refers to the time between sending short messages, which

is automatically sent once every 4 hours by default. The set
number is how often to send short messages. When the
machine fails, the machine information will be sent immediately

text one message

After debugging, select YES and press the red button, and
the machine will send a message to the set number to check
whether the message function is normal

H Capsule Return
(Please adjust according to the machine selection)
Select ON when the machine is equipped with the
egg-twister motor. When the game ends without winning,
the machine will automatically produce a twisted egg.
Choose OFF if there is no egg motor

H Prize motor
(Please adjust according to the machine selection)
Gift security door If the machine has, select ON;
if not, select OFF
annotation：If you choose to open it, the security door
will be closed under normal state. Only when the player
wins the prize will the security door be opened, and the
security door will be closed automatically after taking out the gift.
 F a i l u r e a n d m aint e n ance

The positioning
screw
sensor

motor

Fault description： Fault description： Fault description：

The sensor not sense the The sensor not sense the The microswitch not sense the
registration point registration point registration point
Maintenance： Maintenance： Maintenance：
1.Check for loose wiring 1.Check for loose wiring 1.Check for loose wiring
2. Check whether the 2. Replace the sensor 2.Replace the microswitch
motor is working 3. Replace the mainboard 3.Replace the mainboard
3.Replace the sensor
4. Replace the mainboard

Fault description： Fault description： Fault description

The microswitch not sense the The microswitch not sense the When the anti-theft function is on, the
registration point registration point circuit is not connected or the motor
Maintenance： does not work
Maintenance：
1.Check for loose wiring 1.Check for loose wiring Maintenance:
2.Replace the microswitch 2.Replace the microswitch 1.Check if the line is connected
3.Replace the mainboard 3.Replace the mainboard 2.Check whether the motor is working
3.Replace the mainboard
 F a i l u r e a n d m aint e n ance

Fault description： Fault description：

The microswitch not sense the Left and right motors do not work
registration point
Maintenance：
Maintenance： 1.Check for loose wiring
1.Check for loose wiring 2.Check whether the motor is working
2. Replace the microswitch 3.Replace the motor
3. Replace the mainboard 4.Replace the mainboard

x1,y3 x2,y3 x3,y3 x4,y3 x5,y3

The key failed to enter the gift port when

the machine was in auto-calibration position
Maintenance：Shut down and restart, enter x1,y2 x2,y2 x3,y2 x4,y2 x5,y2
Settings for recalibration

x1,y1 x2,y1 x3,y1 x4,y1 x5,y1

*Same for error-11 to error-25