BARANI INSTITUTE OF INFORMATION TECHNOLOGY

Name : Fawad Hussain

Arid # : 18-Arid-0993

Section : BSCS3-B

Subject : DLD

Submitted to : Ms.Noor
 NOR - OR
Statement:
Designing three basic logic gates using universal gates

Activity-1 Outcomes:
To understand Boolean logic of OR gate by designing OR gate using NOR GATE

Theory:
in this experiment we use IC 7402 ,which is 14 pin IC, which has an ordered universal
pined configuration ,the pin 7 has to be grounded. Connect a NOT using NOR gate at
the output of the NOR to invert and get OR logic.pin 1 should be connected to pin 12,
pin 2 & 3 should be use as an input together , pin 4 will be connected to pin 11 5 and 6
should be use as an input.

Equipment Component :
1. 7402 *1
2. LED *1
3. SPST * 2

Tools:
1. Digital Trainer
2. Single core wire
3. Cutter

Symbolic diagram:
Truth Table:

Procedure:
1. Connect the EES-2001 trainer to the 200V AV Power supply
2. Turn on the trainer to verify the voltage of power using multimeter.
3. Install the IC7402 on the trainer braced board
4. Wire the circuit according to the diagram.
5. Use and of the two switches S2 and S1 for inputs
6. For output indication use any LEDs from L0-L15
7. Supply the VCC =+5V and GND to the pin 14 – 7 of the IC
8. Test all the possible combinations of inputs and verify the output according to the
truth table

In case of any trouble:

1. Check the power supply.
2. Check the VCC and GND at pins 14 and 7 of the IC.
3. Check all the wire connectors.
4. check the circuit wiring and remove the breaks.
5. Check the IC using truth table.
Activity-2 Outcomes: NOR-AND
To understand Boolean logic of AND gate by designing AND gate using NOR gates

Theory:
in this experiment we use IC 7402 ,which is 14 pin IC, which has an ordered universal
pined configuration ,the pin 7 has to be grounded. Connect two NOT using NORs at the
inputs of a NOR to get AND logic.pin 1 and 2 should be use as an input together.pin 3
should be connected to pin 13.pin 4 and 5 should be use as an input together.pin pin 6
should be connected to pin 12.pin 11 is use for output.

Equipment Component :
1. 7402 *1
2. LED *1
3. SPST * 2

Tools:
1. Digital Trainer
2. Single core wire
3. Cutter

Symbolic diagram:
Truth Table:

Procedure:
1. Connect the EES-2001 trainer to the 200V AV Power supply
2. Turn on the trainer to verify the voltage of power using multimeter.
3. Install the IC7402 on the trainer braced board
4. Wire the circuit according to the diagram.
5. Use and of the two switches S2 and S1 for inputs
6. For output indication use any LEDs from L0-L15
7. Supply the VCC =+5V and GND to the pin 14 – 7 of the IC
8. Test all the possible combinations of inputs and verify the output according to the
truth table

In case of any trouble:

6. Check the power supply.
7. Check the VCC and GND at pins 14 and 7 of the IC.
8. Check all the wire connectors.
9. check the circuit wiring and remove the breaks.
10. Check the IC using truth table.
Activity-3 Outcomes: NOR-NOT
To understand Boolean logic of NOT gate by designing NOT gate using NOR gates.

Theory:
in this experiment we use IC 7402 ,which is 14 pin IC, which has an ordered universal
pined configuration ,the pin 7 has to be grounded. It’s simple. Just connect both the
inputs together.pin 1 should be use as an output.pin 2 and 3 should be use as an input
together.

Equipment Component :
4. 7402 *1
5. LED *1
6. SPST * 1

Tools:
4. Digital Trainer
5. Single core wire
6. Cutter

Symbolic diagram:
Truth Table:

Procedure:
9. Connect the EES-2001 trainer to the 200V AV Power supply
10. Turn on the trainer to verify the voltage of power using multimeter.
11. Install the IC7402 on the trainer braced board
12. Wire the circuit according to the diagram.
13. Use and of the two switches S2 and S1 for inputs
14. For output indication use any LEDs from L0-L15
15. Supply the VCC =+5V and GND to the pin 14 – 7 of the IC
16. Test all the possible combinations of inputs and verify the output according to the
truth table

In case of any trouble:

11. Check the power supply.
12. Check the VCC and GND at pins 14 and 7 of the IC.
13. Check all the wire connectors.
14. check the circuit wiring and remove the breaks.
15. Check the IC using truth table.
Statement:
Designing one universal gates using universal gates

Activity-1 Outcomes: NAND – XOR

To understand Boolean logic of XOR gate by designing XOR gate using NAND gates.

Theory:
in this experiment we use IC 7400 ,which is 14 pin IC, which has an ordered universal
pined configuration ,the pin 7 has to be grounded. You share the two inputs with three
gates. The output of the first NAND is the second input to the other two. Finally, another
NAND takes the outputs of these two NAND gates to give the final output.pin 1 should
be connected to pin 9 and also use for taking input.pin 2 should be connected to pin 5
and also use for taking input. 3 and 4 should be connected to pin 10. Pin 6 should be
connected to pin 13.pin 11 should be use for output.

Equipment Component :
7. 7400 *1
8. LED *1
9. SPST * 2

Tools:
7. Digital Trainer
8. Single core wire
9. Cutter

Symbolic diagram:
Truth Table:

Procedure:
17. Connect the EES-2001 trainer to the 200V AV Power supply
18. Turn on the trainer to verify the voltage of power using multimeter.
19. Install the IC7400 on the trainer braced board
20. Wire the circuit according to the diagram.
21. Use and of the two switches S2 and S1 for inputs
22. For output indication use any LEDs from L0-L15
23. Supply the VCC =+5V and GND to the pin 14 – 7 of the IC
24. Test all the possible combinations of inputs and verify the output according to the
truth table

In case of any trouble:

16. Check the power supply.
17. Check the VCC and GND at pins 14 and 7 of the IC.
18. Check all the wire connectors.
19. check the circuit wiring and remove the breaks.
20. Check the IC using truth table.