Scribd
Upload
2K views2 pages

Kone Error

1) The document provides error codes and explanations for issues that may occur with KONE elevator systems. 2) Code 0001 indicates that the elevator position signal has not changed for 30 minutes, requiring power to be turned off. 3) Code 0014 indicates that a safety circuit was not released two times in a row without the elevator reaching its destination, requiring power to be turned off. 4) Many of the error codes relate to signals getting stuck or not being detected properly, requiring the power to be turned off or the system to be overhauled.

Uploaded by

rully hidayatullah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
2K views2 pages

Kone Error

1) The document provides error codes and explanations for issues that may occur with KONE elevator systems. 2) Code 0001 indicates that the elevator position signal has not changed for 30 minutes, requiring power to be turned off. 3) Code 0014 indicates that a safety circuit was not released two times in a row without the elevator reaching its destination, requiring power to be turned off. 4) Many of the error codes relate to signals getting stuck or not being detected properly, requiring the power to be turned off or the system to be overhauled.

Uploaded by

rully hidayatullah
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as TXT, PDF, TXT or read online on Scribd
You are on page 1/ 2

nih dari mbah google

KONE error code ( full version )


Failure reason code
0001 driver long time after a period of the position signal 30/B30 running time
does not change. Immediately stop power off
0004 three consecutive synchronous operation failed. Three consecutive synchronous
operation of the system are not receiving proper leveling signal slowdown after
three failed to stop at the end of the station . Off power
0007 Area 308,030 switch stuck after the start time is not detected falling edge
30/B30 signal. Door zone has been effective operation of the switch to the
destination 30/B30
0008 NVRAM damaged or capacity is not enough when the power transmission capacity
is not enough to detect NVRAM . Replace NVRAM
0014 Area check the circuit did not release any of two consecutive .486.443.1.443:2
without (ACO / ACL) run to the destination floor , shut off electrical service
0015 Area check circuit does not pull any one .486.443.1.443:2 consecutive times
without (ACO / ACL) run to the destination floor , shut off electrical service
0021 safety circuit fails . Safety circuit input a no voltage is immediately
stopped. Safety circuit switched
0022 Hall door barrier. 3 no-voltage input safety circuit stop immediately . Hall
door turns
0023 car door lock will not work. Safety circuit voltage input 2 no stop
immediately . Door sedan turned
0025 start of system failure when the elevator did not stop the main contactor
release does not start . Main contactor failure row
0026 drive system failure . Driven system detects a fault (v3FCK not light ) does
not start. Off power or play overhaul
0039 shorted 77 buttons stuck. Shorted 77 buttons card refuses to start LCEBOPU
board. Until the release button
0042 car lighting monitor lighting no electricity to run the car to the destination
floor. From service until the signal disappears
0044 closed barrier several attempts . Closed door barrier five times but failed .
Door opening does not go off electricity or playing back door opener repair 0048
remain valid reverse signal lasts more than one minute to open the door to keep the
door closed until the signal disappears electricity
0051 start start invalid 5 times unsuccessful , such as landing door may not shut
the door and then try five automatic recovery
0052 down synchronous switching while effectively .77 U and 77N while effectively
stop immediately. RDF can only start at the end of the station automatically
restored
0058 ready to run out. Had requested but the elevator did not start running more
than 100 seconds to stop immediately. Attempt to run off after ten seconds or
playing electric acceleration signal 0060V3F16 overhaul did not receive accelerated
loss of signal -to-end operation of the drive system power off or play station
overhaul
0071 district loss of signal . After several layers 61U / N when the rising edge of
the signal can not be found 30/B30 run to the destination floor. Door shut without
electricity or playing overhaul
0072 61U Signal stuck .61 U signal after leaving the gate area is still not
released for some time to run to the destination floor. Then open to the lowest
floor as still stuck, then shut off electrical service or repair 0071 hit area
through several layers of signal loss 61U / N can not be found when the rising edge
of the signal to run 30/B30 destination floor . door shut without electricity or
playing overhaul
0073 61N signal stuck. Passes through several layers of the door area. 61N can not
find the rising edge of the signal . Off electricity or playing overhaul
0073 61N signal stuck. Passes through several layers of the door area. 61N can not
find the rising edge of the signal . Off electricity or playing overhaul
0074 61N signal stuck .61 N signal after leaving the gate area for some time still
not released. Off power or play overhaul
0075 61U Signal stuck. Passes through several layers of the door area. 61U can not
find the rising edge of the signal . Off electricity or playing overhaul
Automatic recovery after the 0076 are

You might also like