SAVIHost Manual

Manual for SAVIHost by Hermann Seib
Manual by H. G. Fortune
Updated to Version 1.11 (2004 - 11 - 22)
This program is used to have a VSTi run like a standalone application.
This offers two major advantages:

1. VSTi can be used (tested, checked or tried) easily and directly without the need or
search for another host.
2. VSTi can be tested in a temporary directory without the need of the presence of another
host or to search for a dedicated VSTPlugIns-subdirectory. The VSTi-dll can still be used
within other hosts like Cubase, Sonar etc. when copied to that host's VSTPlugins-
subdirectory.
For use just rename SAVIHost.exe to the corresponding VSTi.dll eg:

if there is KPV-Syn.dll rename SAVIHost.exe to KPV-Syn.exe and this will run the VSTi.
Menu-Bar
Most items in the menu-bar are quite obvious:

File: exit the program
Engine: Starts/Stops or Restarts the audio engine
View: have the Toolbar (icons) displayed and MIDI Keyboard (see special note below)
Help: shows info about the standalone hostprogram
Devices:
This is important for enhanced usage: selecting the proper wave device for playback.
On standard home-pcs with no advanced

audio device you'll probably use the
standard wave device used by windows
systems (eg. MME: Wave Mapper)
Default device is standard wave device
used by windows.
Usage of ASIO device drivers will offer a
better performance in most cases. See
documentation of Your sound device for
details.
ASIO-Channel Selection
When using ASIO drivers you will
have access this menu where you
may select different channels for
input and output of the audio-signal
depending on the number of I/O-
channels supported by your audio
device.
Buffersetting:
Buffer: setting the buffer size (in samples)
too low leads to „crackling“ sound. If so
then raise the buffersize until crackling
disappears. With a buffersize quite high
there will be a noticable latency (delay)
until the instrument reacts to strokes on a
MIDI-keyboard. This is dependant on the
performance faculties of the audio device
(soundcard, USB-audioadapter etc.)
Effect: opens the menu for loading or saving patchbanks (*.fxb) and selecting patches
Rename a patch eg. after editing
load a different patchbank

save a patchbank
save a patchbank with a new name
Select MIDI-Channels to be active
Load a single patch

save a single patch
Alt+N switch to next patch program

Alt+P switch to previous patch program
select a group of 16 patches and further select a specific patch within this
group.
Note on loading and saving a single patch should be possible for all VSTi since Ver 1.11 of SAVIHost.
Hint: When saving individual patches (and later reloading) it is advisable to use a specific subdirectory of or
to each VSTI – this ensures to have the correct patches for each VSTi in the right place!
The toolbar:
start/stop the audio-engine of the VSTi
switch to previous or next patch
opens the patch-selector to select a specific patch number
load and save patchbanks (*.fxb)
Display of current tempo and option to change tempo

when clicking on the metrenom icon you get this window
First icon lets you open the oncreen-keyboard,

second icon opens menu to configure this keyboard.
Fullsize screenshot of the onscreen keyboard with two wheels
You can play on the simulated MIDI keyboard with the mouse or the PC keyboard.
Whenever the mouse cursor changes to a little hand (), you can play on the keyboard.
You can resize the keyboard drawing with mouse on the upper border.
The Left Mouse Button acts like a finger; as long as you keep it pressed,the note is
played.
The Right Mouse Button acts as a "sticky finger"; if you press it over a note, this note
keeps on playing until you release it by pressing the right mouse button over it once again.
The keyboard is "dynamic"; the closer to the bottom you touch it with the mouse, the
louder the note sounds. Unfortunately, the PC keyboard is not dynamic, so notes played
with the PC keyboard are played with a predefined velocity.
The keyboard can have up to 3 wheels (see Keyboard Configure on how to activate them),
each can be of the following type: a self-centering Pitch Wheel, a Modulation Wheel, and
an (optional) Velocity Wheel, which is useful for temporarily changing the velocity of keys
entered with the PC keyboard.
If the MIDI keyboard has the input focus, you can also use the PC keyboard to generate
MIDI notes. The following keys can be used:
Below the keyboard, octave indicators can be displayed. They mark the currently active
lower and upper keyboard octaves (i.e., the octaves that can be played on the PC
keyboard). To use other octaves, you can drag the octave indicators to a new position.
The following function keys have been built in:
Left shift, Right shift transposes the PC keyboard's range two octaves down/up
Ins, Del increment/decrement pitch wheel data
Home, End increment/decrement modulation wheel
PgUp, PgDn increment/decrement key velocity
Left, Right decrement/increment upper keyboard octave
Down, Up decrement/increment lower keyboard octave
The default velocity of MIDI notes generated by the PC keyboard can be adjusted with the
Velocity knob on the Keyboard Configure dialog, shown below:
Keyboard configuration:
keyboard shown with activated octave indicators and key labels
In the second tab you can select wheel types and activate some more options like
assigning a selectable MIDI-CC to the second wheel and have arrow-buttons displayed for
fine in- or decrements
This screenshot shows the 2nd wheel set to MIDI-CC 19 to be controlled as well by the two
arrows for fine in- or decrements.
the 3rdtab let's you change the color of the keys – in this example the black keys have
been coloured to blue

SAVIHost Manual

Uploaded by

Copyright:

Available Formats

SAVIHost Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

SAVIHost Manual

Uploaded by

Copyright:

Available Formats

What is SAVIHost used for?

What is SAVIHost used for?

What are some advantages of using VSTi as standalone applications?

What are some advantages of using VSTi as standalone applications?

Manual for SAVIHost by Hermann Seib

Updated to Version 1.11 (2004 - 11 - 22)

This program is used to have a VSTi run like a standalone application.

This offers two major advantages:

For use just rename SAVIHost.exe to the corresponding VSTi.dll eg:

Most items in the menu-bar are quite obvious:

On standard home-pcs with no advanced

Rename a patch eg. after editing

load a different patchbank

Select MIDI-Channels to be active

Load a single patch

Alt+N switch to next patch program

start/stop the audio-engine of the VSTi

switch to previous or next patch

opens the patch-selector to select a specific patch number

load and save patchbanks (*.fxb)

Display of current tempo and option to change tempo

First icon lets you open the oncreen-keyboard,

The following function keys have been built in:

You might also like