Odrzavanje

Indo Jordan Chemical
Co
IJC PREDICTIVE MAINTENANCE

PRACTICES AND ITS IMPACT ON
RELIABILITY
ABOUT THE COMPLEX
• The Phosphoric Acid Complex consists of
– 700 MT P2O5 / day Phosphoric Acid plant,
based on Hydro Agri’s (Norway) Single Stage
Hemi Hydrate process.
– 2,000 MT H2SO4 /day Sulphuric Acid plant,
based on Monsanto’s (USA) Double Conversion
Double Absorption process.
– Associated Utilities.
• In addition, Phosphoric acid storage facility at Aqaba
consists of
– 4 X 5,000 m3 capacity storage tanks.
Contents:
1. Difference between preventive maintenance and
predictive maintenance.
2. IJC Implemented predictive maintenance in
parallel with preventive maintenance.
3. Steps were followed to implement predictive
maintenance.
4. Predictive Maintenance techniques.
5. Achievement and Impact on reliability.
6.Conclusion
1. Difference between preventive mainte
maintenance and
predictive maintenance
e.
Preventive maintenance:
• Preventive maintenance is maintenance that is regularly

performed on a piece of equipment to reduce the chance of
failure .
• Preventative maintenance is performed while the equipment

is still working, so that it does not break down unexpectedly.
• All preventive maintenance programs are time-driven,

that is mean that maintenance based on history .
• Preventive Maintenance depend on MTBF

Predictive maintenance:
• The aim of predictive maintenance is to predict when

equipment failure might occur.
• To prevent occurrence of the failure by performing

maintenance.
• It is philosophy, or attitude, simply stated, uses the

actual operating operation condition of plant equipments
and system to optimize total plant operation.
• Predictive maintenance is a condition- driven

preventive maintenance
2. IJC Implemented predictive maintenance in addition to preventive

maintenance.
Preventive Maintenance Predictive Maintenance
• Routine of scheduling. • Data about the equipment is
collected and analyzed .
• Performing repair tasks • Performing repair to predict

before it becomes a machine breakdown or
necessary. failure.
• Unneeded repairs can • Repairs are made as

happen. needed.
• More cost. • Less cost.
• Reliability is less. • Reliability is high.
3.Steps Were Followed

ollowed To Implement
Imple Predictive
Maintenance.
• Minimize unscheduled equipment failures.
• Minimize maintenance cost.
Objective
• Minimize lost production.
• Determine the equipments should be monitored.

• Determine the parameters that describe the operating
condition.
Procedure • Finalized the required technique need to be followed for
each equipment.
• Create standards. It is important to create standards for
the implementation of the technology, analytical
Documents
standards and reporting standards.
• Prepare the required documents need to be filled by the
team.
3. Steps Were Followed
ollowed To Imple
Implement Predictive
Maintenance.
• Identify what type of instrument to be used.

• Procurement for required instruments. (vibration monitoring,
procurement thermometer
• Dedicated and accountable personnel

• Train the required team for the task.
Training • Train the team to use the tools. Tools manufacture can help
to train them.
• Check the accuracy of the data.

Feed Back • Share the result with your team.
Predictive maintenance technique

1- Vibration Monitoring
• Portable Vibrometer is used.
• Identify the location for measuring

and reference reading.
• Vibration readings were plotted.
• RCA for high vibration.
• Future plan: introduce the

vibration analyzer.
2- Tribology
• Lubricating oil analysis.
• Conserve and extend the useful life of

lubricants.
• Wear particle analysis provides direct

information about the wearing condition of
the machine.
3- Thermography
• Identify the high temperature in equipments, that is
indication for high friction.
• High Temp in lines, vessels.
• Hot spot in furnace.
• High Temp in electrical items.
•
4- Visual inspection
a) Ultrasound
• Use to monitor the noise level.
• The turbulent flow of liquids and gases

through a restricted orifice (i.e., leak).
• Ultrasonic has been, and continues to be, a

primary test methodology for materials testing
2) Visual inspection
• This can vary from one to others plants.
• Checking for any up normal condition.
• Checking for any external effect on the

equipments.
Boiler Details
Test scope and procedure
5. Achievement and Impact on Reliability.
• Ability to minimize the sudden break down for all rotary

equipments.
• Increase the belt life in our horizontal vacuum belt filter

to 4 years compare with before 3 years life. By close
monitoring for the hardness and visual inspection.
• Replacement the waste heat boiler just on time before

catastrophic failure.
• Replacement the turbine rotor just on time to improve

the efficiency and prevent high vibration in turbine.
• Re gasket for plate heat exchanger before
efficiency get reduced.
• Minimize the over-time cost.
• Minimize the inventory.
Conclusion
If we don't apply the Pdm
• Maintenance always need to be standby.
• Maintenance Over-Time will be increased.
• Damage will extend further.

If we apply the Pdm.
• Simply Maintenance team and

Management will be happy
– No surprise break downs

– Reduced need for “back up” equipment
– Minimize maintenance resource

Odrzavanje

Uploaded by

Copyright:

Available Formats

Odrzavanje

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Odrzavanje

Uploaded by

Copyright:

Available Formats

Indo Jordan Chemical

IJC PREDICTIVE MAINTENANCE

• Preventive maintenance is maintenance that is regularly

• Preventative maintenance is performed while the equipment

• All preventive maintenance programs are time-driven,

• Preventive Maintenance depend on MTBF

• The aim of predictive maintenance is to predict when

• To prevent occurrence of the failure by performing

• It is philosophy, or attitude, simply stated, uses the

• Predictive maintenance is a condition- driven

2. IJC Implemented predictive maintenance in addition to preventive

• Performing repair tasks • Performing repair to predict

• Unneeded repairs can • Repairs are made as

• More cost. • Less cost.

• Reliability is less. • Reliability is high.

3.Steps Were Followed

• Determine the equipments should be monitored.

• Identify what type of instrument to be used.

• Dedicated and accountable personnel

• Check the accuracy of the data.

Predictive maintenance technique

• Identify the location for measuring

• Vibration readings were plotted.

• RCA for high vibration.

• Future plan: introduce the

• Lubricating oil analysis.

• Conserve and extend the useful life of

• Wear particle analysis provides direct

• Hot spot in furnace.

• High Temp in electrical items.

• The turbulent flow of liquids and gases

• Ultrasonic has been, and continues to be, a

• Checking for any up normal condition.

• Checking for any external effect on the

5. Achievement and Impact on Reliability.

• Ability to minimize the sudden break down for all rotary

• Increase the belt life in our horizontal vacuum belt filter

• Replacement the waste heat boiler just on time before

• Replacement the turbine rotor just on time to improve

• Minimize the over-time cost.

• Minimize the inventory.

• Maintenance always need to be standby.

• Maintenance Over-Time will be increased.

• Damage will extend further.

• Simply Maintenance team and

– No surprise break downs

You might also like