Technical Specifications

Eclipse Packet Node INU/INUe

ETSI

_d(LF)_Eclipse_PN_ETSI_8Mar13
ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

System Parameters
General
Per Link Per Node
Throughput/Capacity Range Native Carrier Ethernet/IP
[1]
11 - 462 Mbit/s 2.77 Gbit/s
Native TDM 4 -100x E1 100x E1
[2]
4x E3 6x E3
2x STM1 2x STM1
Fixed Modulation Options Fixed QPSK, 16, 32, 64, 128, 256 QAM
Adaptive Coding and Modulation Modulation Options QPSK, 16, 64, 256 QAM
Coding Options Max Throughput, Max System Gain
Co-Channel Operation with XPIC Optional >20dB XPOL improvement
Error Correction LDPC
Adaptive Equalization 24 tap T/2 spaced feed-forward filter

Standards Compliance
EMC EN 301 489-1, EN 301 489-4 (EN 55022 Class A)
Operation EN 300 019, Class 3.1E
Storage EN 300 019, Class 1.2
Transportation EN 300 019, Class 2.3
Safety IEC 60950-1/EN 60950-1

Payload Encryption
Payload encryption Compliance FIPS 197
Cryptography Support AES-CCM (RFC-3610) Cipher suite
Key 128-, 192-, or 256-bit symmetric key
Diffie-Hellman Key agreement method (RFC-2631)

Environmental
Operating Temperature Guaranteed -5° to +55° C
Humidity Guaranteed 0 to 93%, non-condensing
Altitude Guaranteed 4,500 meters

Fault and Configuration Management

Protocol SNMP v2c (standard), v3 (optional)
Secure Management Features Encryption AES-128, -192 or -256
Validated Algorithms FIPS 140-2
Key and Certificate Management ITU-T X.509
Centralized User Accounts RADIUS Protocol (RFC-2865)
Local/remote Configuration Tool Eclipse Portal
Element/Network Management Aviat Networks ProVision™

All specifications are typical values unless otherwise stated, and are subject to change without notice.

[1] Maximum Ethernet Throughput figures are L1 throughput based upon 64 byte frames, and will vary depending upon actual mix of traffic frame
sizes.
[2] E3 is transported as NxE1 using the DAC3xE3M mux option

AVIAT NETWORKS Page 1

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

System Parameters (cont.)

Emission Designator

Emission
7MHz 13.75MHz 14MHz 27.5MHz 28MHz 40MHz 55MHz 56MHz
Designator
QPSK 7M00G7W 13M75G7W 14M0G7W 27M5G7W 28M0G7W 40M0G7W 55M0G7W 56M0G7W
QAM 7M00D7W 13M75D7W 14M0D7W 27M5D7W 28M0D7W 40M0D7W 55M0D7W 56M0D7W

Dispersive Fade Margin (DFM), typical

Capacity Channel BW Modulation Symbol Rate Gross Bit DFM (dB)
(Mbaud) Rate
(Mbit/s)
8-10 Mbit/s 7 MHz QPSK 6.2 12.4 73
18-21 Mbit/s 7 MHz 16 QAM 6.2 24.8 69
29-31 Mbit/s 7 MHz 64 QAM 6.2 37.2 66
41-44 Mbit/s 7 MHz 256 QAM 6.2 49.6 67
17-21 Mbit/s 13.75 MHz QPSK 12.1 24.2 73
35-43 Mbit/s 13.75 MHz 16 QAM 12.1 48.4 65
55.7 Mbit/s 13.75 MHz 32 QAM 12.6 63.0 65
58-64 Mbit/s 13.75 MHz 64 QAM 12.1 72.6 62
82-88 Mbit/s 13.75 MHz 256 QAM 12.1 96.8 57
36-44 Mbit/s 27.50 MHz QPSK 24.7 49.4 68
73-89 Mbit/s 27.50 MHz 16 QAM 24.7 98.8 61
105 Mbit/s 27.50 MHz 32 QAM 24.7 123.5 55
121-133 Mbit/s 27.50 MHz 64 QAM 24.7 148.2 54
155 Mbit/s 27.50 MHz 128 QAM 24.7 172.9 50
170-181 Mbit/s 27.50 MHz 256 QAM 24.7 197.6 48
50-59 Mbit/s 40 MHz QPSK 34.7 69.3 65
101-118 Mbit/s 40 MHz 16 QAM 34.7 138.6 58
156-187 Mbit/s 40 MHz 64 QAM 34.7 208.0 51
238-255 Mbit/s 40 MHz 256 QAM 34.7 277.3 45
74-90 Mbit/s 55 MHz QPSK 49.9 99.7 54
147-182 Mbit/s 55 MHz 16 QAM 49.9 199.4 50
246-268 Mbit/s 55 MHz 64 QAM 49.9 299.1 44
313 Mbit/s 55 MHz 128 QAM 49.9 349.0 41
344-366 Mbit/s 55 MHz 256 QAM 49.9 398.8 37

All specifications are typical values unless otherwise stated, and are subject to change without notice.

AVIAT NETWORKS Page 2

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

Intelligent Node Unit (INU) Common Units

\
IDC, Indoor Chassis 1RU
Dedicated plug-in card slots 2 (NCC, FAN)
Universal plug-in card slots 4
Maximum number of ODUs supported 3
Dimensions (including mounting brackets) 44mm x 482mm x 282.5mm
Weight Empty 2.6 kg

IDCe, Extended Indoor Chassis 2RU

Dedicated plug-in card slots 3 (NCC, NPC, 2RU FAN)
Universal plug-in card slots 9
Maximum number of ODUs supported 6
Dimensions (including mounting brackets) 88mm x 482mm x 282.5mm
Weight Empty 4.8 kg

NCC, Node Controller Card

NMS LAN interface Type 4-port 10/100Base-T Hub
Connector 4x 8-pin RJ-45
Serial Maintenance Interface Standard Complies to TIA/EIA-561
Speed 1200 bps to 115.2 kbps
Connector 8-pin RJ-45
Configuration memory, removable 512 Mbyte CompactFlash card (on-board)
Electrical DC Supply input range -40.5 to -60 VDC
DC Fuse type and rating 25A fast-acting ceramic body cartridge
Over voltage protection < -70 VDC
Under voltage protection -32 VDC
DC connector 2-pin DSUB power type
Power consumption 11 W
LED Indicators 2x Tri-state ('Test', 'Status')
Dimensions (including front panel and rear connector) 22mm x 260mm x 268mm
Weight 0.6 kg

NPC, Node Protection Card

Electrical DC Supply input range -40.5 to -60 VDC
DC Fuse type and rating 25A fast-acting ceramic body cartridge
Over voltage protection < -70 VDC
Under voltage protection -32 VDC
DC connector type 2-pin DSUB power type
Power consumption 8W
LED Indicators 2x Tri-state ('Protect', 'Status')
Dimensions (including front panel and rear connector) 22mm x 130mm x 268mm
Weight 0.4 kg

FAN, Fan Card 1RU

Fans 2
LED Indicators 1x Red LED ('Fault')
Power consumption 1W
Dimensions (including front panel and rear connector) 44mm x 40mm x 264mm
Weight 0.23 kg

AVIAT NETWORKS Page 3

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

Intelligent Node Unit (INU) Common Units (cont.)

FAN, Fan Card 2RU
Fans 2
LED Indicators 1x Red LED ('Fault')
Power consumption 2W
Weight 0.46 kg

AUX, Auxilary Services Card

Aux Data Channels 3
Interface RS232 or RS422
Line Rate Asynchronous 1.2 to 19.2 kbit/s
Synchronous 64 kbit/s
Aux Data Connector High Density DSUB26
[1]
External Alarm Inputs TTL Inputs Up to 6
TTL input thresholds 0.8V max low, 2.0V min high
[1]
External Alarm Outputs Form C Relays Up to 4
Alarms Connector High Density DSUB15
LED Indicators 1x Tri-state ('Status')
Power consumption 1W
Dimensions (including front panel and rear connector) 22mm x 130mm x 268mm
Weight 0.35 kg

All specifications are typical values unless otherwise stated, and are subject to change without notice.
[1] For applications requiring additional alarm inputs or outputs, multiple AUX cards can be installed if free INU/INUe slots are available.

AVIAT NETWORKS Page 4

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

Radio Access Cards (RAC)

General
IF connector SMA[1]
IF interface Transmit 311 MHz, -8.0 to -12.0 dBm
Receive 126 MHz, -8 to -27 dBm
LED Indicators 2x Tri-state ('Online', 'Status')
Dimensions (including front panel and rear connector) 22mm x 130mm x 268mm
Weight < 0.38 kg
Secondary Lightning protection Gas tube, 150 V

RAC 60E/RAC 6XE

Data Packet Plane (DPP) Interface Interfaces, electrical 1x 1000Base-T
Connector RJ-45
RFUs supported ODU600, ODU300hp, ODU300ep
[2]
Capacities supported Ethernet to 462 Mbit/s , 1-100x E1, 1-2x STM1
Modulations supported Fixed Modulation QPSK, 16, 32, 64, 128, 256QAM
Adaptive Coding and Modulation Modulation Options QPSK, 16, 64, 256 QAM
Coding Options Max Throughput, Max System Gain
XPD Improvement RAC 6XE only 20 dB
XPIC connectors RAC 6XE only 2x SMB
Power consumption RAC 60E / RAC 6XE 13 W / 19 W

All specifications are typical values unless otherwise stated, and are subject to change without notice.
[1] RAC Installation Kit includes 3 meter jumper cable, SMA to N-type.
[2] Maximum Ethernet Throughput figures are L1 based upon 64 byte frames, and will vary depending upon actual mix of traffic frame sizes.

AVIAT NETWORKS Page 5

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

Data Access Cards (DAC) - Ethernet

General
LED Indicators 2x Tri-state ('Online', 'Status')
RJ-45 Ethernet Interface ("Link Status", "Activity")
Power Consumption (nominal) 13 W (DAC GE3)
Dimensions (including front panel and rear connector) 22mm x 130mm x 268mm
Weight (nominal) < 0.34 kg
DAC GE3 - Carrier Ethernet/IP
Ethernet Standards Compliance Ethernet IEEE 802.3
Networking Protocols IPv4 and IPv6
DAC GE3
Backplane Throughput Maximum 200 Mbit/s
Packet Plane Throughput Maximum 2 Gbit/s
Switch Capacity 5x 1 Gbit/s user ports
+ 6x channels
User Ports RJ-45 3x 10/100/1000Base-T

SFP 2x Optical LC or Electrical RJ-45

Optical SFP Options 1550 nm single mode 1000Base-ZX

1310 nm single mode 1000Base-LX
850 nm multimode 1000Base-SX
Electrical SFP Options 10/100/1000Base-T
1000Base-T
Backplane Ports (Channels) 6
Burst and Frame Handling (Typical) Buffer Size Per Port Configurable up to 1.28 Mbytes[1]

Max Frame Size 10000 bytes bi-directional

Throughput Acceleration IFG & Preamble Suppression Yes

Frame Size Dependent
MAC address register 16000 entries
QoS Port Based Prioritization Yes
IEEE 802.1p QoS/CoS Bits Yes
DSCP IPv6/IPv4
MPLS EXP bits Yes
Remarking MPLS Exp and DSCP to 802.1p

Transmission Queues 8
Scheduling Strict, DWRR or Strict+DWRR
(flexible per port)

VLANs VLAN Tagging IEEE 802.1Q

Q-in-Q (Provider Bridging) IEEE 802.1ad
VLAN Translation Yes
Congestion Management Flow Control IEEE 802.3x
Ingress Policing TrTCM (per port and per flow)

CIR, EIR, CBS, EBS

Broadcast/Multicast Storm Protection Yes

AVIAT NETWORKS Page 6

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

Data Access Cards (DAC) - Ethernet (cont.)

DAC GE3 - Carrier Ethernet/IP (cont.)
Redundancy 1+1 Card Protection Yes
Link Status Propagation Yes
Synchronization Synchronous Ethernet ITU-T G.8262
ESMC/SSM ITU-T G.8264
Internal Reference Built-in Stratum 3 clock
Link Aggregation L1LA (Layer 1) DPP ports
Fixed or adaptive modulation
LAG (Layer 2) IEEE 802.1AX static or LACP
Layer 2-4 hashing
User ports, DPP ports and channels
(LACP on user ports only)

Fixed modulation
Ring Protection RSTP IEEE 802.1w
ERP ITU-T G.8032v2

Ethernet OAM IEEE 802.1ag/ITU-T Y.1731 CFM ETH-CC, ETH-LB,

ETH-LT, ETH-RDI,
ETH-AIS
ITU-T Y.1731 PM ETH-LM,
ETH-DM and ETH-DVM
Monitoring Port and Channel Status Yes
Performance Graphs Yes
Per-Queue Performance Statistics Yes
RMON-1 Ports and Channels
Diagnostics Port Shutdown Yes
Port Mirror Yes

All specifications are typical values unless otherwise stated, and are subject to change without notice.
[1] Dependent upon configuration settings and number of active interfaces.

AVIAT NETWORKS Page 7

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

Data Access Cards (DAC) - TDM

General
Power consumption (nominal) Max 4 W
Dimensions (including front panel and rear connector) 22mm x 130mm x 268mm
Weight (nominal) < 0.34 kg

DAC 4x, DAC 16x v2 - TDM (NxE1)

LED Indicators 1x Tri-state: 'Status'
Interface, configurable DAC 4x Electrical 1 to 4x 2.048 Mbit/s (E1)
DAC 16x v2 Electrical 1 to 16x 2.048 Mbit/s (E1)
Electrical interface parameters Standards Compliance E1 Compliant to ITU-T Rec. G.703, G.823
Line code E1 HDB3
Connectors DAC 4x 4x RJ-45
DAC 16x v2 2x 50-pin HDR
Impedance E1 75Ω unbalanced or
120Ω balanced,
configurable
Redundancy Hot-standby tributary protection (DAC 16x v2 only)
Ethernet over unframed E1 2 Mbit/s per trib; 32 Mbit/s per DAC (DAC 16x v2 only)

DAC 3xE3M - TDM (NxE3 Mux)

LED Indicators 2x Tri-state: 'Online', 'Status'
Interface 1 to 3x 34.368 Mbit/s (E3)
Functionality 2x E3 (32.768 Mbit/s) to 2x 16xE1 mux, channelized
2x E3 transparent (34.368 Mbit/s) to 2x 17xE1 mux, unchannelized
Electrical interface parameters Standards Compliance Compliant to ITU-T Rec. G.703, G.823
Line code HDB3
Connectors Slimline BNC
Impedance 75Ω unbalanced
Redundancy Hot-standby tributary protection

DAC 155o, 2x155o, 2x155e - SDH (1x/2xSTM1)

LED Indicators 1x Tri-state: 'Status'
Interface, configurable DAC 155o Optical 1x 155.52 Mbit/s (STM1)
DAC 2x155o Optical 1 or 2x 155.52 Mbit/s (STM1)
DAC 2x155e Electrical 1 or 2x 155.52 Mbit/s (STM1)
Electrical interface parameters Standards Compliance Compliant to ITU-T Rec. G.703, G.825
Line code CMI
Connectors BNC
Impedance 75Ω unbalanced
Optical interface parameters Standards Compliance Compliant to ITU-T Rec. G.957, G.825
Optical interface Short Range S-1.1
Connectors SC
Tx Output Center Wavelength 1310 nm
Tx Average Optical Output Power -15 to -8 dBm
Rx Sensitivity -31 dBm
Rx Input Power Saturation -7 dBm
Redundancy Hot-standby tributary protection

All specifications are typical values unless otherwise stated, and are subject to change without notice.

AVIAT NETWORKS Page 8

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

Data Access Cards (DAC) - TDM (cont.)

DAC 155oM/DAC 155eM STM1 Multiplexer (1xSTM1)
LED Indicators 2x Tri-state: 'Online', 'Status'
Interface 1x 155.52 Mbit/s (STM1)
Functionality 1x STM1 (Interface) to 63x E1 (TDM Bus) Mux
DAC 155eM Electrical interface Electrical SFP - Coaxial
DIN 1.0/2.3 75 Ohm
DAC 155oM Optical interface Optical SFP - LC
Single
Mode Single Mode
Long Short Range Multi Mode
Range S1.1
L1.1
Tx Output Center Wavelength 1310 nm 1310 nm 850 nm
Tx Launch Power Min/Max -5 to 0 dBm -15 to -8 dBm -10 to -4 dBm
Rx Min Input Power -35 dBm -34 dBm -24 dBm
Rx Input Power Saturation 0 dBm 0 dBm 0 dBm
Timing modes, configurable Recovered clock
Local Reference Clock (XO)
Redundancy Hot-standby tributary protection

All specifications are typical values unless otherwise stated, and are subject to change without notice.

AVIAT NETWORKS Page 9

ECLIPSE PACKET NODE ETSI TECHNICAL SPECIFICATIONS

WWW.AVIATNETWORKS.COM
Aviat, Aviat Networks and the Aviat logo are trademarks or registered trademarks of Aviat Networks, Inc.
Eclipse is a trademark of Aviat U.S. Inc.

©Aviat Networks, Inc. 2012 All Rights Reserved. Data subject to change. _d(lf)_Eclipse_PN_ETSI_8Mar13
Change Log
Revision Issue Date Changes
Draft Revision 1a, Nov 2011 11-Nov-11 1st Release for comment
Draft Revision 1b, Nov 2011 15/11/2011 Added 40 MHz BW specs
Draft Revision 1c, Dec 2011 20-Dec-11 Updated DFM specs
Draft Revision 1e, Mar 2012 27-Mar-12 Updated/corrected DAC GEv2 and GE3 specs
Draft Revision 1f, May 2012 8-May-12 corrected Regulatory compliance
Draft Revision 1g, June 2012 14-Jun-12 Updated Ethernet OAM for DAC GE3

8-Mar-13 Remove DAC GEv2, removed RWPR

s