Scribd
Upload
35 views

Data Engine

This document provides instructions for inspecting and removing various emission control system components, including: - The evaporative emissions canister and canister close valve. Removal involves disconnecting hoses and electrical connectors. Inspection checks for damage and measures resistance. - The intake air temperature sensor. Inspection measures resistance between terminals and compares to specifications. - The mass air flow sensor. Removal requires disconnecting hoses and electrical connectors and removing mounting bolts. Inspection is not described.

Uploaded by

Wawan Satiawan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
35 views

Data Engine

This document provides instructions for inspecting and removing various emission control system components, including: - The evaporative emissions canister and canister close valve. Removal involves disconnecting hoses and electrical connectors. Inspection checks for damage and measures resistance. - The intake air temperature sensor. Inspection measures resistance between terminals and compares to specifications. - The mass air flow sensor. Removal requires disconnecting hoses and electrical connectors and removing mounting bolts. Inspection is not described.

Uploaded by

Wawan Satiawan
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

21-136 EMISSION

CONTROLSYSTEM

EvaporativeEmissionsCanister
lnspection
1. Visuallycheckfor damageand replaceif
necessary.

3. Disconnectthe CanisterCloseValveConnectorbv
pryingthe RetainerClip out of the connectorwithi
oicktool.
it Celttion
Use care when prying out the Retainer Clip.
Canister Close Valve 4. Disconnectthe CanisterCloseValvelrom the wire
hamessconnector.
Removal
1. Remove
the Canister
CloseValvehose.

lnspection
1. MeasureCanisterCloseValveresistance.
2. Removethe CanisterCloseValvemountinobracket
bolts. Resistance:
Approximately25 O at 68"F(20'C)
2. lf notas specified,replacethe CanisterClose
Valve.

Revision 1, U'l5/99
EMISSIONCONTROLSYSTEM 21.137

4. lf not as specified,replaceIATsensor.
5. Connectthe IATsensor.

Removal
1. Disconnectthe IATsensorc€nnector
by pryingthe retainerclip-out of the connectorwith
a picktool.
2. Removethe IATsensorfromair cleanerassembly.

lnstallation
1. Installa newwasherand the intakeair temperature
sensorlo air cleanerassembly.
2. Connectthe intakeair temperat!{re
connector,

Installation
1. Connectthe CanisterCloseValveConnector.
2- Reinstallthe RetainerClip.
3. Beinstallthe CanisterCloseValvemountingbracket
bolts.
4. Reinstallthe CanisterCloseValvehose.

Bt{/A2l001

MASSAIR FLOWSENSOR
(HOTF|LMTYPE)
Removal
* Notice
Do not drop or subject the sensorto shock.Do not
put obiectsinside the sensot
1. Disconnectthe massair llow sensor@nnector.
2. Loosenair inlakehose retainingdampson both
IntakeAir Temperature
Sensor sidesof the massair flow sensor.
Inspection 3. Disconnectthe air intakehosefromthe massair
flow sensor.
1. Turnthe ignitionswitchOFF.
4. Removethe two boltsattachingthe massair flow
2. DisconnectIATsensorconnector. sensorto the mountingbracket.
3. Usinga ohmmeter,measureresislancebetween 5. Removethe massair flow sensor.
terminals1 and2 of the IATsensor.

Resistancei 2.21-2.69KO 68"F= (20'C)


Revision1, 8/15199

You might also like