Fluid mechanics, science concerned with the response of fluids to forces exerted upon them.

It is a branch of classical physics with applications of great importance in hydraulic

and aeronautical engineering, chemical engineering, meteorology, and zoology.
The most familiar fluid is of course water, and an encyclopaedia of the 19th century probably
would have dealt with the subject under the separate headings of hydrostatics, the science of
water at rest, and hydrodynamics, the science of water in motion. Archimedes founded
hydrostatics in about 250 BC when, according to legend, he leapt out of his bath and ran
naked through the streets of Syracuse crying “Eureka!”; it has undergone rather little
development since. The foundations of hydrodynamics, on the other hand, were not laid until
the 18th century when mathematicians such as Leonhard Euler and Daniel Bernoulli began to
explore the consequences, for a virtually continuous medium like water, of
the dynamic principles that Newton had enunciated for systems composed of discrete
particles. Their work was continued in the 19th century by several mathematicians and
physicists of the first rank, notably G.G. Stokes and William Thomson. By the end of the
century explanations had been found for a host of intriguing phenomena having to do with
the flow of water through tubes and orifices, the waves that ships moving through water
leave behind them, raindrops on windowpanes, and the like. There was still no proper
understanding, however, of problems as fundamental as that of water flowing past a fixed
obstacle and exerting a drag force upon it; the theory of potential flow, which worked so well
in other contexts, yielded results that at relatively high flow rates were grossly at variance
with experiment. This problem was not properly understood until 1904, when the German
physicist Ludwig Prandtl introduced the concept of the boundary layer (see
below Hydrodynamics: Boundary layers and separation). Prandtl’s career continued into the
period in which the first manned aircraft were developed. Since that time, the flow of air has
been of as much interest to physicists and engineers as the flow of water, and hydrodynamics
has, as a consequence, become fluid dynamics. The term fluid mechanics, as used here,
embraces both fluid dynamics and the subject still generally referred to as hydrostatics.
One other representative of the 20th century who deserves mention here besides Prandtl
is Geoffrey Taylor of England. Taylor remained a classical physicist while most of his
contemporaries were turning their attention to the problems of atomic structure and quantum
mechanics, and he made several unexpected and important discoveries in the field of fluid
mechanics. The richness of fluid mechanics is due in large part to a term in the basic
equation of the motion of fluids which is nonlinear—i.e., one that involves the
fluid velocity twice over. It is characteristic of systems described by nonlinear equations that
under certain conditions they become unstable and begin behaving in ways that seem at first
sight to be totally chaotic. In the case of fluids, chaotic behaviour is very common and is
called turbulence. Mathematicians have now begun to recognize patterns in chaos that can be
analyzed fruitfully, and this development suggests that fluid mechanics will remain a field of
active research well into the 21st century. (For a discussion of the concept of chaos,
see physical science, principles of.)
Fluid mechanics is a subject with almost endless ramifications, and the account that follows
is necessarily incomplete. Some knowledge of the basic properties of fluids will be needed; a
survey of the most relevant properties is given in the next section. For further details,
see thermodynamics and liquid.
Get unlimited ad-free access to all Britannica’s trusted content.Start Your Free Trial
Today

Basic Properties Of Fluids

Fluids are not strictly continuous media in the way that all the successors of Euler and
Bernoulli have assumed, for they are composed of discrete molecules. The molecules,
however, are so small and, except in gases at very low pressures, the number of molecules
per millilitre is so enormous that they need not be viewed as individual entities. There are a
few liquids, known as liquid crystals, in which the molecules are packed together in such a
way as to make the properties of the medium locally anisotropic, but the vast majority of
fluids (including air and water) are isotropic. In fluid mechanics, the state of an isotropic
fluid may be completely described by defining its mean mass per unit volume, or density (ρ),
its temperature (T), and its velocity (v) at every point in space, and just what the connection
is between these macroscopic properties and the positions and velocities of individual
molecules is of no direct relevance.
A word perhaps is needed about the difference between gases and liquids, though the
difference is easier to perceive than to describe. In gases the molecules are sufficiently far
apart to move almost independently of one another, and gases tend to expand to fill any
volume available to them. In liquids the molecules are more or less in contact, and the short-
range attractive forces between them make them cohere; the molecules are moving too fast to
settle down into the ordered arrays that are characteristic of solids, but not so fast that they
can fly apart. Thus, samples of liquid can exist as drops or as jets with free surfaces, or they
can sit in beakers constrained only by gravity, in a way that samples of gas cannot. Such
samples may evaporate in time, as molecules one by one pick up enough speed to escape
across the free surface and are not replaced. The lifetime of liquid drops and jets, however, is
normally long enough for evaporation to be ignored.
There are two sorts of stress that may exist in any solid or fluid medium, and the difference
between them may be illustrated by reference to a brick held between two hands. If the
holder moves his hands toward each other, he exerts pressure on the brick; if he moves one
hand toward his body and the other away from it, then he exerts what is called a shear stress.
A solid substance such as a brick can withstand stresses of both types, but fluids, by
definition, yield to shear stresses no matter how small these stresses may be. They do so at a
rate determined by the fluid’s viscosity. This property, about which more will be said later, is
a measure of the friction that arises when adjacent layers of fluid slip over one another. It
follows that the shear stresses are everywhere zero in a fluid at rest and in equilibrium, and
from this it follows that the pressure (that is, force per unit area) acting perpendicular to all
planes in the fluid is the same irrespective of their orientation (Pascal’s law). For an isotropic
fluid in equilibrium there is only one value of the local pressure (p) consistent with the stated
values for ρ and T. These three quantities are linked together by what is called the equation
of state for the fluid.
molar mass, or an average molar mass if the gas is a mixture; for air, the appropriate average
is about 29 × 10−3 kilogram per mole. For other fluids knowledge of the equation of state is
often incomplete. Except under very extreme conditions, however, all one needs to know is
how the density changes when the pressure is changed by a small amount, and this is
described by the compressibility of the fluid—either the isothermal compressibility, βT, or
the adiabatic compressibility, βS, according to circumstance. When an element of fluid is
compressed, the work done on it tends to heat it up. If the heat has time to drain away to the
surroundings and the temperature of the fluid remains essentially unchanged throughout, then
βT is the relevant quantity. If virtually none of the heat escapes, as is more commonly the
case in flow problems because the thermal conductivity of most fluids is poor, then the flow
is said to be adiabatic, and βS is needed instead. (The S refers to entropy, which remains
constant in an adiabatic process provided that it takes place slowly enough to be treated as
“reversible” in the thermodynamic sense.) For gases that obey equation (118), it is evident
that p and ρ are proportional to one another in an isothermal process, and
where γ is about 1.4 for air and takes similar values for other common gases. For liquids the
ratio between the isothermal and adiabatic compressibilities is much closer to unity. For
liquids, however, both compressibilities are normally much less than p−1, and the simplifying
assumption that they are zero is often justified.
The factor γ is not only the ratio between two compressibilities; it is also the ratio between
two principal specific heats. The molar specific heat is the amount of heat required to raise
the temperature of one mole through one degree. This is greater if the substance is allowed to
expand as it is heated, and therefore to do work, than if its volume is fixed. The principal
molar specific heats, CP and CV, refer to heating at constant pressure and constant volume,
respectively, and
For air, CP is about 3.5 R.
Solids can be stretched without breaking, and liquids, though not gases, can withstand
stretching, too. Thus, if the pressure is steadily reduced in a specimen of very pure water,
bubbles will ultimately appear, but they may not do so until the pressure is negative and well
below -107 newton per square metre; this is 100 times greater in magnitude than the
(positive) pressure exerted by the Earth’s atmosphere. Water owes its high ideal strength to
the fact that rupture involves breaking links of attraction between molecules on either side of
the plane on which rupture occurs; work must be done to break these links. However, its
strength is drastically reduced by anything that provides a nucleus at which the process
known as cavitation (formation of vapour- or gas-filled cavities) can begin, and a liquid
containing suspended dust particles or dissolved gases is liable to cavitate quite easily.
Work also must be done if a free liquid drop of spherical shape is to be drawn out into a long
thin cylinder or deformed in any other way that increases its surface area. Here again work is
needed to break intermolecular links. The surface of a liquid behaves, in fact, as if it were an
elastic membrane under tension, except that the tension exerted by an elastic membrane
increases when the membrane is stretched in a way that the tension exerted by a liquid
surface does not. Surface tension is what causes liquids to rise up capillary tubes, what
supports hanging liquid drops, what limits the formation of ripples on the surface of liquids,
and so on.
Fluid mechanics is the branch of physics concerned with the mechanics of fluids (liquids, gases, and plasmas)
and the forces on them. It has applications in a wide range of disciplines,
including mechanical, civil, chemical and biomedical
engineering, geophysics, oceanography, meteorology, astrophysics, and biology.
It can be divided into fluid statics, the study of fluids at rest; and fluid dynamics, the study of the effect of forces
on fluid motion. It is a branch of continuum mechanics, a subject which models matter without using the
information that it is made out of atoms; that is, it models matter from a macroscopic viewpoint rather than
from microscopic. Fluid mechanics, especially fluid dynamics, is an active field of research, typically
mathematically complex. Many problems are partly or wholly unsolved and are best addressed by numerical
methods, typically using computers. A modern discipline, called computational fluid dynamics (CFD), is devoted
to this approach. Particle image velocimetry, an experimental method for visualizing and analyzing fluid flow,
also takes advantage of the highly visual nature of fluid flow.
The study of fluid mechanics goes back at least to the days of ancient Greece, when Archimedes investigated
fluid statics and buoyancy and formulated his famous law known now as the Archimedes' principle, which was
published in his work On Floating Bodies—generally considered to be the first major work on fluid mechanics.
Rapid advancement in fluid mechanics began with Leonardo da Vinci (observations and
experiments), Evangelista Torricelli (invented the barometer), Isaac Newton (investigated viscosity) and Blaise
Pascal (researched hydrostatics, formulated Pascal's law), and was continued by Daniel Bernoulli with the
introduction of mathematical fluid dynamics in Hydrodynamica (1739).
Inviscid flow was further analyzed by various mathematicians Jean le Rond d'Alembert, Joseph Louis
Lagrange, Pierre-Simon Laplace, Siméon Denis Poisson) and viscous flow was explored by a multitude
of engineers including Jean Léonard Marie Poiseuille and Gotthilf Hagen. Further mathematical justification
was provided by Claude-Louis Navier and George Gabriel Stokes in the Navier–Stokes equations,
and boundary layers were investigated (Ludwig Prandtl, Theodore von Kármán), while various scientists such
as Osborne Reynolds, Andrey Kolmogorov, and Geoffrey Ingram Taylor advanced the understanding of fluid
viscosity and turbulence.

Main branches[edit]
Fluid statics[edit]
Main article: Fluid statics
Fluid statics or hydrostatics is the branch of fluid mechanics that studies fluids at rest. It embraces the study of
the conditions under which fluids are at rest in stable equilibrium; and is contrasted with fluid dynamics, the
study of fluids in motion. Hydrostatics offers physical explanations for many phenomena of everyday life, such
as why atmospheric pressure changes with altitude, why wood and oil float on water, and why the surface of
water is always level whatever the shape of its container. Hydrostatics is fundamental to hydraulics,
the engineering of equipment for storing, transporting and using fluids. It is also relevant to some aspects
of geophysics and astrophysics (for example, in understanding plate tectonics and anomalies in the Earth's
gravitational field), to meteorology, to medicine (in the context of blood pressure), and many other fields.

Fluid dynamics[edit]
Main article: Fluid dynamics
Fluid dynamics is a subdiscipline of fluid mechanics that deals with fluid flow—the science of liquids and
gases in motion. Fluid dynamics offers a systematic structure—which underlies these practical disciplines—that
embraces empirical and semi-empirical laws derived from flow measurement and used to solve practical
problems. The solution to a fluid dynamics problem typically involves calculating various properties of the fluid,
such as velocity, pressure, density, and temperature, as functions of space and time. It has several
subdisciplines itself, including aerodynamics (the study of air and other gases in motion)
and hydrodynamics (the study of liquids in motion). Fluid dynamics has a wide range of applications, including
calculating forces and movements on aircraft, determining the mass flow rate of petroleum through pipelines,
predicting evolving weather patterns, understanding nebulae in interstellar space and modeling explosions.
Some fluid-dynamical principles are used in traffic engineering and crowd dynamics.

Relationship to continuum mechanics[edit]

Fluid mechanics is a subdiscipline of continuum mechanics, as illustrated in the following table.

Elasticity
Describes materials that return to their rest shape after
applied stresses are removed.
Solid mechanics
The study of the physics of
continuous materials with a
defined rest shape.
Plasticity
Describes materials that permanently
Continuum deform after a sufficient applied stress.
mechanics Rheology
The study of the The study of materials with
physics of continuous both solid and fluid
materials characteristics.
Non-Newtonian fluids do not
undergo strain rates proportional
Fluid mechanics to the applied shear stress.
The study of the physics of
continuous materials which
deform when subjected to a force.
Newtonian fluids undergo strain rates proportional to the
applied shear stress.

In a mechanical view, a fluid is a substance that does not support shear stress; that is why a fluid at rest has
the shape of its containing vessel. A fluid at rest has no shear stress.

Assumptions[edit]

Balance for some integrated fluid quantity in a control volume enclosed by a control surface.

The assumptions inherent to a fluid mechanical treatment of a physical system can be expressed in terms of
mathematical equations. Fundamentally, every fluid mechanical system is assumed to obey:

 Conservation of mass
 Conservation of energy
 Conservation of momentum
 The continuum assumption
For example, the assumption that mass is conserved means that for any fixed control volume (for example, a
spherical volume)—enclosed by a control surface—the rate of change of the mass contained in that volume is
equal to the rate at which mass is passing through the surface from outside to inside, minus the rate at which
mass is passing from inside to outside. This can be expressed as an equation in integral form over the control
volume.[1]
The continuum assumption is an idealization of continuum mechanics under which fluids can be treated
as continuous, even though, on a microscopic scale, they are composed of molecules. Under the continuum
assumption, macroscopic (observed/measurable) properties such as density, pressure, temperature, and bulk
velocity are taken to be well-defined at "infinitesimal" volume elements—small in comparison to the
characteristic length scale of the system, but large in comparison to molecular length scale. Fluid properties
can vary continuously from one volume element to another and are average values of the molecular properties.
The continuum hypothesis can lead to inaccurate results in applications like supersonic speed flows, or
molecular flows on nano scale. Those problems for which the continuum hypothesis fails can be solved
using statistical mechanics. To determine whether or not the continuum hypothesis applies, the Knudsen
number, defined as the ratio of the molecular mean free path to the characteristic length scale, is evaluated.
Problems with Knudsen numbers below 0.1 can be evaluated using the continuum hypothesis, but molecular
approach (statistical mechanics) can be applied for all ranges of Knudsen numbers.

Navier–Stokes equations[edit]
Main article: Navier–Stokes equations
The Navier–Stokes equations (named after Claude-Louis Navier and George Gabriel Stokes) are differential
equations that describe the force balance at a given point within a fluid. For an incompressible fluid with vector

velocity field , the Navier–Stokes equations are

.
These differential equations are the analogues for deformable materials to Newton's equations of motion
for particles – the Navier–Stokes equations describe changes in momentum (force) in response

to pressure and viscosity, parameterized by the kinematic viscosity here. Occasionally, body
forces, such as the gravitational force or Lorentz force are added to the equations.
Solutions of the Navier–Stokes equations for a given physical problem must be sought with the help
of calculus. In practical terms, only the simplest cases can be solved exactly in this way. These cases
generally involve non-turbulent, steady flow in which the Reynolds number is small. For more complex
cases, especially those involving turbulence, such as global weather systems, aerodynamics,
hydrodynamics and many more, solutions of the Navier–Stokes equations can currently only be found with
the help of computers. This branch of science is called computational fluid dynamics.

Inviscid and viscous fluids[edit]

An inviscid fluid has no viscosity, . In practice, an inviscid flow is an idealization, one that facilitates
mathematical treatment. In fact, purely inviscid flows are only known to be realized in the case
of superfluidity. Otherwise, fluids are generally viscous, a property that is often most important within
a boundary layer near a solid surface,[2] where the flow must match onto the no-slip condition at the solid.
In some cases, the mathematics of a fluid mechanical system can be treated by assuming that the fluid
outside of boundary layers is inviscid, and then matching its solution onto that for a thin laminar boundary
layer.
For fluid flow over a porous boundary, the fluid velocity can be discontinuous between the free fluid and
the fluid in the porous media (this is related to the Beavers and Joseph condition). Further, it is useful at
low subsonic speeds to assume that gas is incompressible—that is, the density of the gas does not
change even though the speed and static pressure change.

Newtonian versus non-Newtonian fluids[edit]

A Newtonian fluid (named after Isaac Newton) is defined to be a fluid whose shear stress is linearly
proportional to the velocity gradient in the direction perpendicular to the plane of shear. This definition
means regardless of the forces acting on a fluid, it continues to flow. For example, water is a Newtonian
fluid, because it continues to display fluid properties no matter how much it is stirred or mixed. A slightly
less rigorous definition is that the drag of a small object being moved slowly through the fluid is
proportional to the force applied to the object. (Compare friction). Important fluids, like water as well as
most gases, behave—to good approximation—as a Newtonian fluid under normal conditions on Earth.[3]
By contrast, stirring a non-Newtonian fluid can leave a "hole" behind. This will gradually fill up over time—
this behavior is seen in materials such as pudding, oobleck, or sand (although sand isn't strictly a fluid).
Alternatively, stirring a non-Newtonian fluid can cause the viscosity to decrease, so the fluid appears
"thinner" (this is seen in non-drip paints). There are many types of non-Newtonian fluids, as they are
defined to be something that fails to obey a particular property—for example, most fluids with long
molecular chains can react in a non-Newtonian manner.[3]

Equations for a Newtonian fluid[edit]

Main article: Newtonian fluid
The constant of proportionality between the viscous stress tensor and the velocity gradient is known as
the viscosity. A simple equation to describe incompressible Newtonian fluid behavior is

where

is the shear stress exerted by the fluid ("drag")

is the fluid viscosity—a constant of proportionality

is the velocity gradient perpendicular to the direction of shear.

For a Newtonian fluid, the viscosity, by definition, depends only
on temperature and pressure, not on the forces acting upon it. If the fluid
is incompressible the equation governing the viscous stress (in Cartesian coordinates) is

where

is the shear stress on the face of a fluid element in the direction

is the velocity in the direction

is the direction coordinate.

If the fluid is not incompressible the general form for the viscous
stress in a Newtonian fluid is

where is the second viscosity coefficient (or bulk viscosity).

If a fluid does not obey this relation, it is termed a non-Newtonian
fluid, of which there are several types. Non-Newtonian fluids can
be either plastic, Bingham plastic, pseudoplastic, dilatant,
thixotropic, rheopectic, viscoelastic.
 In some applications, another rough broad division among fluids
is made: ideal and non-ideal fluids. An ideal fluid is non-viscous
and offers no resistance whatsoever to a shearing force. An ideal
fluid really does not exist, but in some calculations, the
assumption is justifiable. One example of this is the flow far from
solid surfaces. In many cases, the viscous effects are
concentrated near the solid boundaries (such as in boundary
layers) while in regions of the flow field far away from the
boundaries the viscous effects can be neglected and the fluid
there is treated as it were inviscid (ideal flow). When the viscosity
is neglected, the term containing the viscous stress

tensor in the Navier–Stokes equation vanishes. The

equation reduced in this form is called the Euler equation.
v