EA4 Finish Metal

1.
216
NIPPON EA4 FINISH

Product Description:
NIPPON EA4 FINISH is a two-pack amine-adduct cured epoxy finish for use on steel and cement
surfaces where chemical, oil and abrasion resistant coating is required. It is recommended for non-
immersion services. If it is to be applied over steel, it has to be used in combination with the appropriate
primers as recommended below. If it is to be applied over concrete the surface should be acid-treated
prior to application. NIPPON EA4 FINISH is also available in non-skid quality.
Physical Characteristics Of Paint:

Colour : As per colour card
Texture : High Gloss
Specific Gravity : 1.00 - 1.30, depending on colours
Solid Content : 51 ± 3% by volume
(ASTM D2697 1973)
Abrasion : Good resistance to abrasion and mechanical damage
Adhesion : Excellent on correctly prepared and primed surfaces
Temperature : Dry service temperature range up to 100°C
Recommendation For Use:
Surface Preparation:
Steel Surface
When used as a top coat within a NIPPON protective system, the steel surface would have been
prepared in accordance with the recommendations provided within the product data sheet of the primer
being used. This will normally be abrasive blast cleaning to minimum Sa 2½ ISO 8501-1:1988 or other
equivalent international standard. The primed surface must be dry and free from any abrasive residues,
dirt, oil and grease and other contaminants prior to painting.
Concrete Surface
The surface must be treated with about 5% sulphuric acid solution until effervescence has stopped. It
should then be washed thoroughly with clean water and allowed to dry completely before coating with
Nippon EA4 Finish.
Recommended No. Of Coats : 1 - 3 coats
Recommended Film Thickness Per : 50 ~ 80 microns for dry film

Coat 100 ~ 160 microns for wet film
2
Theoretical Coverage At : 10.2 m /litre (for dry film thickness of 50 microns)
2
Recommended Film Thickness 6.4 m /litre (for dry film thickness of 80 microns)
Theoretical Coverage = Volume Solids (%) X 10

(m2/litre) Dry Film Thickness (µ)
Practical Coverage 2
: 8.2 m /litre (for dry film thickness of 50 microns)
(20% Loss Factor) 2
5.1 m /litre (for dry film thickness of 80 microns)
Note : This theoretical coverage rate has been calculated from the volume solids of the material and is related to the amount of
coating applied onto a perfectly smooth surface without wastage. For a practical coverage rate, due allowance should be made
for atmospheric conditions, surface roughness, geometry of the article being coated, the skill of applicator, method of application
etc. when estimating quantities required for a particular job.
NIPPON EA4 FINISH Page 1 of 3
JAN 08 VERSION
1.216
Application Methods : Brush, roller, compressed air spray and airless spray. Preferably
use airless spray if a thicker coat is required in one application.
Brush, roller, compressed air spray generally lead to lower film
thickness, so more applications may be required to obtain the
recommended thickness per coat.
1) Brush/Roller : Recommended for small areas and touch-up only. Good quality
brushes and mohair/ short nap rollers should be used with full
strokes. Avoid rebrushing. Thin up to 10% by volume of SA-65
Thinner for proper flow-out. Additional coats may be required to
achieve minimum specified film thickness.
2) Spray : When airless spray is being used, excessive high tip spraying
pressure should be avoided. The minimum pressure at the pump
conducive with good atomisation should be used.
2
Guiding Data For Airless : Delivery Pressure : 140-170 kg/cm
Spray : Tip Size : 0.015”-0.017”
: Spray Angle : 60 - 70°
: If necessary, add up to 5% thinner by volume for application by

Thinning brush, roller and airless spray; about 10%-15% by volume for
application by compressed air spray.
:
Mixing Ratio 4 parts by volume of Nippon EA4 Finish (Base) to 1 part by
volume of Nippon EA4 Finish (Hardener). Stir the content of the
base component, continue stirring and gradually add the total
contents of the hardener component, continue stirring until a
homogeneous mix is obtained.
Pot Life at 25°C to 30°C : 6 - 8 hours after mixing

Thinner : SA-65 Thinner
Cleaning Solvent : SA-65 Thinner

Note: All equipment should be cleaned IMMEDIATELY with thinner after use. For thinning, substitute thinners other than those
approved or supplied by Nippon Paint may adversely affect the product performance and void product warranty whether
expressed or implied.
Drying Time at 25°°C to 30°°C : Dry to touch - 2-3 hours

: Dry to handle - 16 hours
: Dry to overcoat - Minimum 16 hours
Curing Time at 25°°C to 30°°C : 6-7 days

Note: Drying time will become remarkably delayed under low temperature. Overcoating the previous coat of Nippon EA4
Finish should be done within 6 ~ 7 days but preferably as soon as possible after it has been allowed 16 hours drying or else, it is
desirable to roughen it by dry sanding with sandpaper before it is overcoated. This is to ensure proper intercoat adhesion.
Exposure of the paint film to water, chemical and abrasion should be avoided as far as possible before full cure of the coating.
When chalking occurs, chalks should be removed by water washing. Allow the surface to dry thoroughly prior to overcoating.
Standard Packing : 5 litres (4.0 litres Base and 1.0 litre Hardener)
Shelf Life at 25°°C to 30°°C : 2 years

JAN 08 VERSION
1.216
Environmental Conditions During Application:

1. Do not apply when the relative humidity exceeds 85% or when the surface to be coated is less
than 3°C above the dew point.
2. Do not apply at temperature below 7°C. If not, drying and overcoating times will be
considerably extended.
3. During application of the paint, naked flame, welding operations and smoking should not be
allowed and adequate ventilation should be provided.
Safety, Health and Environmental Information:

1. In the wet state, this product is highly inflammable. Protect from extremes of temperature &
store in a cool place. In case of fire, blanket flames with foam, carbon dioxide or dry chemicals.
2. Keep away from sources of ignition. No smoking.
3. Keep container tightly closed and keep out of reach from children.
4. Do not breathe vapour/spray. Applying paint to large surface areas under closed environment
should use air supplied breathing equipment. For small areas or short periods, a suitable
cartridge mask should be worn.
Inhalation : Remove to fresh air, loosen collar and keep patient rested.
Ingestion : In case of accidental ingestion. DO NOT INDUCE VOMITING. Seek
immediate medical attention.
5. Avoid contact with skin and eyes. Wear suitable protective coating such as overalls, goggles,
dust masks and gloves. Use a barrier cream.
Eyes : In the event of accidental splashes, flush eyes with water immediately
and obtain medical advice.
Skin : Wash skin thoroughly with soap and water or approved industrial
cleaner. DO NOT USE solvent or thinners.
6. Care must be taken when transporting paint. Keep container in a secure upright position.
7. Do not empty into drains or watercourses. Dispose of any paint waste in accordance with the
appropriate Environmental Quality Regulations.
Note : A Chemical Safety Data Sheet (CSDS) is available upon request.
NOTE :
The above information is given to the best of our knowledge based on laboratory tests and practical experience. However, since
we cannot anticipate or control the many conditions under which our products may be used, we can only guarantee the accuracy
of our information or the suitability of our products in any given condition.
We reserve the right to alter the given data without notice.

JAN 08 VERSION

EA4 Finish Metal

Uploaded by

Copyright:

Available Formats

EA4 Finish Metal

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

EA4 Finish Metal

Uploaded by

Copyright:

Available Formats

1.

NIPPON EA4 FINISH

Physical Characteristics Of Paint:

Recommended Film Thickness Per : 50 ~ 80 microns for dry film

Theoretical Coverage = Volume Solids (%) X 10

: If necessary, add up to 5% thinner by volume for application by

Pot Life at 25°C to 30°C : 6 - 8 hours after mixing

Cleaning Solvent : SA-65 Thinner

Drying Time at 25°°C to 30°°C : Dry to touch - 2-3 hours

Curing Time at 25°°C to 30°°C : 6-7 days

Shelf Life at 25°°C to 30°°C : 2 years

NIPPON EA4 FINISH Page 2 of 3

Environmental Conditions During Application:

Safety, Health and Environmental Information:

Note : A Chemical Safety Data Sheet (CSDS) is available upon request.

We reserve the right to alter the given data without notice.

NIPPON EA4 FINISH Page 3 of 3

You might also like