Scribd
Upload
164 views25 pages

Seismic Sources Geophysics

For a velocity increase with depth: - The reflection coefficient Ar is negative (since Z1 < Z2) - The transmission coefficient At is positive - The reflected wave arrives back at the surface after 2t, where t is the two-way travel time to the interface.

Uploaded by

badrhashmi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
164 views25 pages

Seismic Sources Geophysics

For a velocity increase with depth: - The reflection coefficient Ar is negative (since Z1 < Z2) - The transmission coefficient At is positive - The reflected wave arrives back at the surface after 2t, where t is the two-way travel time to the interface.

Uploaded by

badrhashmi
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 25

Seismic Sources

HOW TO GENERATE SEISMIC WAVES?


Exploration seismology – mostly artificial sources
à active technique
Natural sources can also be used (e.g. earthquakes) – usually
for tectonic studies (passive seismic exploration)
!
What is a good source?
- economical, efficient, convenient
- safe and environmentally acceptable
- sufficient energy over suitable frequency range
- repeatable
Land seismic sources

Explosives: - usually detonated in boreholes or buried


PROS
- sharp, impulsive, high amplitude (mostly P-wave)
- reasonably cheap
CONS
- signal is not repeatable
- slow (borehole drilling)
- can be destructive
An impulsive signal can also be generated by:
- hammer on a metal plate (Lab 3)
- weight dropped from truck or helicopter
- firearms - shotguns, rifles
- building implosions
- nuclear explosion tests

(www.ldeo.columbia.edu/res/pi/
(http://earthquake.usgs.gov/regional/pacnw/ Monitoring/News/nkorea_2006.html)
ships/nyt2001.html)
Peaceful Nuclear and chemical
bomb tests were conducted by the
former Soviet Union
(1955-1988),some profiles have
produced prolific information on the
crust and upper mantle structures.

Ryberg et al., 1998

!4
www.Wiki.com
Vibroseis Method (“Thumper trucks”)

ayer-1heavy truck that transmits low


amplitude vibrations
- sweep over a range of
frequencies (10-100Hz) for 10-20 s
0.8 1 1.2 1.4 1.6 1.8 2
ayer 2

0.8 1 1.2 1.4 1.6 1.8 2


2

0.8 1 1.2 1.4


us.jetpcb.com 1.6 1.8 2
(www.lithoprobe.ca)
Vibroseis Method (“Thumper trucks” 10+ MPa)

PROS
- well-defined, repeatable
- little disturbance
- can also create S-waves
!
CONS
- need hard surface
- need accessible areas
- need to buy trucks ($$$)

(www.lithoprobe.ca)
Processing Vibroseis Data

- signal is spread out over time – therefore reflections of


interest will also be spread out
n from base of layer 1
- can isolate reflections using cross-correlation
- works well even with lots of noise
0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 2
n from 2base of layer 2
Vibroseis signal
Amplitude

-2
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
0.4 2 0.6 0.8 1 1.2 1.4 1.6 1.8 2
signal + noise
Amplitude

n 1 + Reflection
0
2

-2
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
2
Marine seismic sources

Explosives - generally not used


Air gun - most common source
- bubble of compressed air 1 air gun

PROS:
- reliable, repeatable, inexpensive
CONS:
- bubble pulse oscillates
- only P-waves are created (why?)
7 air guns
- may be harmful to marine animals

(Kearey et al. 2002)


Air gun arrays: 1. minimize reverberation
2. Recover all frequencies (10s of MPa pressure). www.wikipedia.org
Sparkers, Pingers, Boomers

- high frequency, electrically produced source


- order of increasing strength (pingers, sparkers, boomers,
airguns). sample ‘squid’ sparker
!
PROS:
ACD Technology
- well-defined, repeatable, inexpensive
!
CONS:
- high frequency (10-100,000 Hz) à rapid attenuation
!
- good for shallow seafloor mapping / surveying
woodshole.er.usgs.gov

The sparker is a relatively higher powered sound source,


dependant on an electrical arc which momentarily vaporizes
water between positive and negative leads. The collapsing
bubbles produce a broad band (50Hz - 4 kHz) omni
directional pulse.
Seismic sources
cover a wide
frequency range

(Kearey et al., 2002)


Seismic detectors (chapter 3)

- convert ground motion into an electrical signal (recorded)


- displacement, velocity, acceleration
- 3 components
- for seismic exploration
- source is usually a P-wave that arrives near-vertical
- in the past, record only vertical motion (fast changing)
- recording system – timing must be accurate (< 1 ms), gps is
being used for 3-component seismometers.
Moving-Coil Geophone (most common)
- coil inside magnet
- relative motion of coil and
magnet due to ground motion
produces electric voltage
- voltage proportional to
velocity

Seismometers
- similar to geophones, more
sensitive to lower frequencies
- Usually 3 component
- earthquake/microseismic
studies
Deployment of our group: (CRANE seismic array)

Trillium 240
Temporary Seismometer Setup

Gu et al., 2011
Marine detectors
Hydrophones
-detect a change in water pressure
-convert to electric signal
- only record P-waves
- usually towed behind a ship on a neutrally buoyant streamer
- pressure sensors, compasses, tail buoys
- adjust depth with fins
- often multiple streamers are used to get 3D coverage
!
Ocean Bottom Seismometers (OBS)
- seismometer/geophone in a metal
casing
- dropped overboard and sink to
seafloor
- recovered by releasing weights
- can contain 3 component
seismometers (http://woodshole.er.usgs.gov/
operations/obs/)
- hard to position accurately
- limited life (battery, disk space)
- deep-sea fishing issues
- rotation induced direction uncertainty
(www.oceansatlas.org/unatlas)
Sample OBS system diagram

Release transducer
hydrophone

battery disk
Upper sphere
digitizer sensor

Lower sphere

hook

anchor
Seismic Reflection

We will focus P-waves in this class


but the same ideas apply to S-waves.
4.1 Reflection at Normal Incidence (section 2.3.3)

Reflection coefficient:
R = Ar/Ai
!
Transmission coefficient:
T = At/Ai
!
Note that these coefficients
(refracted give the relative amplitudes
wave) of all the waves
- usually assume that incident
wave amplitude is 1
Reflection at Normal Incidence

Partitioning of energy into


reflection and transmission
depends on:
• the angle of incidence
• the acoustic impedance of
each layer:
Z1 = ρ1v1

!
Z2 = ρ2v2
Zoeppritz Equations

For normal incidence, can show:

Z 2 − Z1 A r
R 12 = =
Z 2 + Z1 A i

2 Z1 At
T12 = =
Z 2 + Z1 A i
Note that: R12 + T12 = 1
Z 2 − Z1 A r 2 Z1 At
R 12 = = T12 = =
Z 2 + Z1 A i Z 2 + Z1 A i
• Z1=Z2 à no reflection
(does NOT mean ρ1=ρ2 &
v1= v2)
• R: -1 to +1
• generally ±0.2 or less
• sign = polarity
• negative when Z1>Z2
• T is positive, can be >1
CASE 1: Velocity increase with depth

Assume (unless otherwise


stated):
• initial amplitude is 1
• velocity and density are
constant in each layer
• no geometrical spreading,
attenuation, scattering

What are Ar and At?


What time does the reflected wave arrive
back at the surface?

You might also like