Scribd
Upload
165 views4 pages

Unigen Plus Parallel Lines Calibration

This document provides a procedure to calibrate the paralleling lines on a Unigen Plus A51Z1-A51M109 controller. The procedure involves: 1. Flashing new software onto the Unigen Plus controller. 2. Establishing a TCP/IP connection to calibrate parameters. 3. Calibrating the 0V of the paralleling lines by adjusting variable E01223 until the value of E00107 is 0% with 0V input. 4. Calibrating the 3V of the lines by adjusting variable E01224 until E00107 is 100% with 100% load. 5. Saving the calibration by writing parameters to flash memory.

Uploaded by

Javed Iqbal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
165 views4 pages

Unigen Plus Parallel Lines Calibration

This document provides a procedure to calibrate the paralleling lines on a Unigen Plus A51Z1-A51M109 controller. The procedure involves: 1. Flashing new software onto the Unigen Plus controller. 2. Establishing a TCP/IP connection to calibrate parameters. 3. Calibrating the 0V of the paralleling lines by adjusting variable E01223 until the value of E00107 is 0% with 0V input. 4. Calibrating the 3V of the lines by adjusting variable E01224 until E00107 is 100% with 100% load. 5. Saving the calibration by writing parameters to flash memory.

Uploaded by

Javed Iqbal
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

UNIGEN Plus

M109/M114

September 2006

Procedure A51 Z1 8 0005 B-En

Calibration of paralleling lines.

CRE Technology believes that all information provided herein is correct and reliable and reserves the right to
update at any time. CRE Technology does not assume any responsibility for its use unless otherwise expressly
undertaken.
A51 Z1 8 0005 B-En.doc

CRE technology
Allée Charles-Victor Naudin - Zone des Templiers - Sophia Antipolis
06410 BIOT - FRANCE
Téléphone : + 33 (0)4.92.38.86.82 - Fax : + 33 (0)4.92.38.86.83
www.cretechnology.com [email protected]
RCS Antibes : 7488 625 000 15 - N°TVA FR54 488 625 583

Unigen - paralleling lines - A51 Z1 8 0005 B-En page 1/4


Introduction
This procedure will describe the way to calibrate paralleling lines.

Procedure
With a Unigen Plus A51Z1-A51M109, you need to do the following action to have a good calibration of the
paralleling lines.

1. Flash of the new software.


• Put the boot strap on the Unigen Plus.
• Connect the Unigen Plus to the PC with the serial cable RS232.
• Put the power supply of the Unigen Plus.
• Start the software Flash-IT.
i. Tab ‘option’:
Select enable on the user-serial-number generation;
Put the address 0x001800;
Put the prefix and number like that:
Ex: serial number = 0106A001 prefix= 0106A number = 001.
ii. Tab ‘config’:
Select ‘autodetect’;
Select ‘sector-erase’.
iii. Tab ‘file:
Select ‘*.h86’ on the bottom of the window;
Select the file A51fullV1_02M114.h86 (provide in the e-mail);
Select ‘Analysis+download’.
iv. At the end:
The status window is green;
Stop the software ‘Flash it’;
Stop the power of the Unigen Plus;
Remove the boot strap of the Unigen;
Put the power of the Unigen Plus.

2. Connection TCP-IP with the Unigen Plus


• Establish the TCP-IP connection with the Unigen Plus;
• Start the web browser (Internet Explorer, Netscape,….);
• In the “location“ or “address” field of the web browser, enter the URL of the Unigen Plus:
http://unigen;
• The Unigen password page should appear in the browser window. Enter your password.

3. Calibration of the 0V of the paralleling lines.


• In the ‘Information Page’, put in boxes variables ‘E01223’, ‘E01224’, ‘E00107’ and ‘E10025’
and push ‘Save’.
• Put 0V in the ‘Breaker input’ in terminal 5 or close the breaker of the genset and see the value
of the variable ‘E00107’, if you have 0% it’s ok if you have more of 0% you need to increase
the value of the variable ‘E01123’ if you have less of 0% you need to decrease the value of the
variable ‘E01223’.
The good value of the variable ‘E01223’ is between 775 and 790.
• To change the value of a parameter. When you are in the ‘information Page’, click esc /
configuration / modification by variable nb / put the number of the variable you want to change
the value (ex: 1223) / Save /modify the value(ex:778) / save / Information page.

Unigen - paralleling lines - A51 Z1 8 0005 B-En page 2/4


Variable you need to see in the information page. (Here the calibration of the 0V is bad).

To modify the value of a variable.

4. Calibration of the 3V of the paralleling lines.


• Put 0V in the ‘Breaker input’ in terminal 5 or close the breaker of the genset, put 100% of load
and adjust single turn potentiometer of kW nominal to have exactly the value of 100.0% in the
parameter ‘E10025’ and see the value of the variable ‘E00107’, if you have 100.0% it’s ok if
you have more of 100.0% you need to increase the value of the variable ‘E01124’ if you have
less of 100.0% you need to decrease the value of ‘E01224’.
The good value of the variable ‘E01224’ is between 310 and 320.
• To change the value of a parameter. When you are in the ‘information Page’, click esc /
configuration / modification by variable nb / put the number of the variable you want to change
the value (ex: 1224) / Save /modify the value(ex:312) / save / Information page.

Unigen - paralleling lines - A51 Z1 8 0005 B-En page 3/4


5. Saving of the calibration of paralleling lines.
• When the breaker is closed and you have 0% of load and you can see 0% in the variable
E00107 , it’s OK for the calibration of the 0v of the paralleling lines.
• When the breaker is closed and you have 100% of load and you can see 100% in the variable
E00107, it’s OK for the calibration of the 3V of the paralleling lines.
• Save the calibration of paralleling lines: when you are in the ‘information Page’, open the
breaker of the genset, click esc / system / save all parameters / Flash it.

Main variable involved in the calibration of the paralleling lines:

Variable Default
Label Description
number value
V01223 PWM plines 0V Calibration of the v of the paralleling lines 778
V01224 PWM plines 3V Calibration of the v of the paralleling lines 312
V00107 In Pines Input of the paralleling lines
V10025 G1 kW% Geenrator global KW in percent of Nominal

Unigen - paralleling lines - A51 Z1 8 0005 B-En page 4/4

You might also like