1 Electronics Semi Conductor Theory Jeemain - Guru

JEEMAIN.
GURU
JEE-Physics
SEMI CONDUCTOR - ELECTRONICS

ENERGY BANDS IN SOLIDS
Based on Pauli's exclusion principle
In an isolated atom electrons present in energy level but in solid, atoms are not isolated, there is interaction
among each other, due to this energy level splitted into different energy levels. Quantity of these different
energy levels depends on the quantity of interacting atoms. Splitting of sharp and closely compact energy levels
result into energy bands. They are discrete in nature. Order of energy levels in a band is 1023 and their energy
difference = 10 –23 eV.
Energy Band
Range of energy possessed by an electron in a solid is known as energy band.
Valence Ba nd (VB)
Range of energies possessed by valence electron is known as valence band.
(a) Have bonded electrons.
(b) No flow of current due to such electrons.
(c) Always fulfill by electrons.
Conduction Band (CB)
Range of energies possessed by free electron is known as conduction band.
(a) It has conducting electrons.
(b) Current flows due to such electrons.
(c) If conduction band is fully empty then current conduction is not possible.
(d) Electrons may exist or not in it.
Forbidden Energy gap (FEG) (Eg)
 Eg = (C B)min – (V B)max
Energy gap between conduction band and valence band, where no free electron can exist.
band energy (eV)
 Width of forbidden energy gap depends upon the nature of substance.
conduction band
 Width is more, then valence electrons are strongly attached with nucleus
E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Electronics\Eng\1. Electronics-Semi Conductor Theory.p65
forbidden
energy gap
 Width of forbidden energy gap is represented in eV. valence band
 As temperature increases forbidden energy gap decreases (very slightly).
CL ASSIFICATION OF CONDUCTORS, INSUL ATORS AND SEMICONDUCTOR : -
On the basis of the relative values of electrical conductivity and energy bands the solids are broadly classified
into three categories
(i) Conductors
(ii) Semiconductors
(iii) Insulator
E 1
JEEMAIN.GURU
JEE-Physics
Compari son bet ween conductor, semiconductor a nd i nsulator :

Properties Conductor Semiconductor Insulator
–2 –8 –5 6 11 19
Resistivity 10 – 10 m 10 – 10 m 10 – 10 m
2 8 5 –6 –11 –19
Conductivity 10 – 10 mho/m 10 – 10 mho/m 10 – 10 mho/m
Temp. Coefficient Positive Negative Negative (Very slightly)
of resistance ()
Current Due to free Due to electrons No current
electrons and holes
Conduction Band Conduction Band
Conduction Band
Electron Energy
Electron Energy
Electron Energy
Overlapping Forbidden Eg  3eV
No gap region Gap Eg  1ev Forbidden
Gap
Energy band diagram
Valence Band Valence Band Valence Band
Conductor Semi conductor Insulator
Forbidden energy gap  0eV  1eV  3eV

Example : Pt, Al, Cu, Ag Ge, Si, GaAs, Wood, plastic,
GaF 2 Diamond, Mica
CONCEPT OF "HOLES" IN SEMICONDUCTORS
Due to external energy (temp. or radiation) when electron goes from valence band to conduction band (i.e.
bonded electrons becomes free) a vacancy of free e– creats in valence band, hole free e–
which has same charge as electron but positive. This positively
Si Si Si Si
charged vacancy is termed as hole and shown in figure.
• It is deficiency of electron in VB.

Si Si Si Si
• It's acts as positive charge carrier.
• It's effective mass is more than electron. Si Si Si Si
• It's mobility is less than electron.
Note : Hole acts as virtual charge carrier, although it has no physical significance.
GOLDEN KEY POINTS

• Number of electrons reaching from VB to CB at temperature T kelvin
E g
–  E 
3/2
n = A T e 2kT
 AT 3 / 2 exp  – g 
 2kT 
where
k = Boltzmann constant = 1.38  10-23 J/K T = absolute temperature
A = constant Eg = energy gap between CB and VB
12
• In silicon at room temperature out of 10 Si atoms only one electron goes from VB to CB.
• In germanium at room temperature out of 109 Ge atoms only one electron goes from VB to CB.
2
E
JEEMAIN.GURU
JEE-Physics
EFFECT OF TEMPER ATURE ON SEMICONDUCTOR
At absolute zero kelvin temperature Above absolute temperature
At this temperautre covalent bonds are very With increase in temperature few valence
strong and there are no free electrons and electrons jump into conduction band and hence
semiconductor behaves as perfect insulator. it behaves as poor conductor.
hole free e–
Si Si Si Si
Si Si Si Si
Si Si Si Si
Si Si Si Si
Si Si Si Si
Si Si Si Si
at 0 K
at high temperature
Valence band fully filled
Valence band partially empty
Conduction band fully empty
Conduction band partially filled
EFFECT OF IMPURITY IN SEMICONDUCTOR

Doping is a method of addition of "desirable" impurity atoms to pure semiconductor to increase conductivity of
semiconductor. or
Doping is a process of deliberate addition of a desirable impurity atoms to a pure semiconductor to modify its
properties in controlled manner.
Added impurity atoms are called dopants.
The impurity added may be  1 part per million (ppm).
 The dopant atom should take the position of semiconductor atom in the lattice.
 The presence of the dopant atom should not distort the crystal lattice.
 The size of the dopant atom should be almost the same as that of the crystal atom.
 The concentration of dopant atoms should not be large (not more than 1% of the crystal atom).
It is to be noted that the doping of a semiconductor increases its electrical conductivity to a great extent.
GOLDEN KEY POINTS
• The concentration of dopant atoms be very low, doping ratio is vary from
impure : pure :: 1 : 106 to 1 : 1010 In general it is 1 : 108
• There are two main method of doping.
(i) Alloy method (ii) Diffusion method (The best)
• The size of dopant atom (impurity) should be almost the same as that of crystal atom. So that crystalline
structure of solid remain unchanged.
CLASSIFICATION OF SEMICONDUCTOR
SEMICONDUCTOR
Intrinsic semiconductor Extrinsic semiconductor (doped semicondutor)
(pure form of Ge, Si)
ne = nh = ni N-type P-type
trivalent impurity
pentavalent impurity
(Ga, B, In, Al)
(P, As, Sb etc.)
donar impurity (ND) acceptor impurity (NA)
ne >> nh nh >> ne
E 3
JEEMAIN.GURU
JEE-Physics
N type semiconductor
When a pure semiconductor (Si or Ge) is doped by pentavalent impurity (P, As, Sb, Bi) then four electrons out
of the five valence electrons of impurity take part, in covalent bonding, with four silicon atoms surrounding it and
the fifth electron is set free. These impurity atoms which donate free e– for conduction are called as Donar
impurity (ND). Due to donar impurity free e– increases very much so it is called as "N" type semiconductor. By
donating e– impurity atoms get positive charge and hence known as "Immobile Donar positive Ion". In N-type
semiconductor free e– are called as "majority" charge carriers and "holes" are called as "minority" charge carriers.
thermally
generated e–
Si As Si Si
thermally
generated hole free electrons
Si Si Si Si
–
donar e
positive minority
donar ions hole
As Si Si As
N-type semiconductor
N-type semiconducting crystal
P type semiconductor
When a pure semiconductor (Si or Ge) is doped by trivalent impurity (B, Al, In, Ga) then outer most three
electrons of the valence band of impurity take part, in covalent bonding with four silicon atoms surrounding it
and except one electron from semiconductor and make hole in semiconductor. These impurity atoms which
accept bonded e– from valance band are called as Acceptor impurity (NA). Here holes increases very much so it
is called as "P" type semiconductor and impurity ions known as "Immobile Acceptor negative Ion". In P-type
semiconductor free e– are called as minority charge carries and holes are called as majority charge carriers.
Extra hole created by
acceptor impurity atom
thermally
–
generated e
Si Al– Si Si
holes
thermally
generated hole
Si Si Si Si negative
acceptor
ions minority e
– –
Al Si Si Al
P-type semiconductor
P-type semiconducting crystal
4
E
JEEMAIN.GURU
JEE-Physics
Intrinsic Semiconductor N-type (Pentavalent impurity) P-t ype(Trivalent impurit y)
CB CB CB
donor
impurity acceptor
1. level impurity
VB VB VB level
free hole
electron
positive negative
2. donar ion acceptor
ion
3. Current due to Mainly due to electrons Mainly due to holes
electron and hole
4. ne = nh = ni nh << ne (ND ~ ne) nh >> ne (NA ~ nh)
5. I = Ie + Ih I ~ Ie I ~ Ih
6. Entirely neutral Entirely neutral Entirely neutral

7. Quantity of electrons Majority - Electrons Majority - Holes
and holes are equal Minority - Holes Minority - Electrons
Mass action Law

In semiconductors due to thermal effect, generation of free e– and hole takes place.
Apart from the process of generation, recombination also occurs simultaneously, in which free e– further recombine
with hole.
At equilibrium rate of generation of charge carries is equal to rate of recombination of charge carrier.
The recombination occurs due to e– colliding with a hole, larger value of ne or nh, higher is the probability of their
recombination.
Hence for a given semiconductor rate of recombination  ne × nh
so rate of recombination = R ne × nh R = recombination coefficient,
The value of R remains constant for a solid, according to the law of thermodynamics until crystalline lattice
structure remains same.
For intrinsic semiconductor ne = nh = ni
so rate of recombination = R ni2
R ne × nh = R ni2  ni2 = ne × nh
Under thermal equilibrium, the product of the concentration 'ne' of free electrons and the concentration nh of
holes is a constant and it is independent of the amount of doping by acceptor and donor impurities.
Thus from mass action law n e  n h  n 12
E 5
JEEMAIN.GURU
JEE-Physics
Electron-hole Recomb inati on :
It is necessarly to complete a bond that electron is shared from neighbouring atoms or it may also be received
from conduction bond. In the second case electron recombines with the hole of valnce bond. This process
is known as electron-hole recombination.
The breaking of bonds or generation of electron-hole pairs, and completion of bonds due to recombination
is taking place continuously.
At equilibrium, the rate of generation becomes equal to the rate of recombination, giving a fixed number
of free electrons and holes.
E x . 1 The energy of a photon of sodium light (  = 589 nm) equals the band gap of a semiconducting material. Find :
(a) the minimum energy E required to create a hole-electron pair.
E
(b) the value of at a temperature of 300 K.
kT
hc 12400
S o l . (a) E  (in eV) so E  (E is in eV and  is in Å)  = 5890 Å
e 
12400 E 2.1  1.6  10 19 J

so E  2.1eV (b)   81
5890 kT 1.38  10 23  300
E x . 2 A P type semiconductor has acceptor level 57 meV above the valence band. What is maximum wavelength of
light required to create a hole ?
hc hc 6.62  10 34  3  10 8
Sol. E   = = 217100 Å
 E 57  10 3  1.6  10 19
E x . 3 A silicon specimen is made into a p-type semiconductor by doping on an average one indium atom per
5 × 107silicon atoms. If the number density of atoms in the silicon specimen is 5 × 1028 atoms/m3; find the
number of acceptor atoms in silicon per cubic centimeter.
S o l . The doping of one indium atom in silicon semiconductor will produce one acceptor atom in p-type semiconductor.
Since one indium atom has been dopped per 5 × 107 silicon atoms, so number density of acceptor atoms in
5  10 28
silicon   10 21 atom/m3 = = 1015 atoms/cm3
5  10 7 E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Electronics\Eng\1. Electronics-Semi Conductor Theory.p65
E x . 4 A pure Ge specimen is doped with A. The number density of acceptor atoms is approximately 1021 m –3. If
density of electron holes pair in an intrinsuc semiconductor is approximately 1019m–3, the number density of
electrons in the specimen is :
S o l . In pure semiconductor electron-hole pair ni = 1019 m–3
acceptor impurity N A = 10 21 m –3
Holes concentration nh = 1021 m–3
2
n 2i 1019 
electrons concentration = ne =  = 1017 m–3
nh 10 21
6
E
JEEMAIN.GURU
JEE-Physics
E x . 5 Pure Si at 300 K has equal electron (ne) and hole (nh) concentrations of 1.5 × 1016 m–3. Dopping by indium
increases nh to 3 × 1022 m–3. Calculate ne in the doped Si.
S o l . For a doped semi-conductor in thermal equilebrium nenh = n 2i (Law of mass action)
n 2i (1.5  10 16 )2
ne   = 7.5 × 109 m–3
hh 3  10 22

RESISTIVITY AND CONDUCTIVITY OF SEMICONDUCTOR A
Conduction in conductor

Relation between current (I) and drift velocity (vd )
I = ne A vd n = number of electron in unit volume E= V

A= cross sectional area
V
I
current density J = amp/m 2 = ne vd drift velocity of electron vd = E
A
J = ne E J = E
Conductivityne Resistivity
vd
Mobility  
E
Conduction in Semiconductor
Intrinsic semiconductor P - type N - type
ne = nh n h >> n e n e >> n h
J = ne [ ve + vh] J  e nh vh J  e ne ve
1 1 1
  = en [ e + h ]    e nh h    e ne e
  
GOLDEN KEY POINTS
• Due to impurity the conductivity increases approximately 105 times

• sc = e + h = neee + nh eh = e(neµe + nhµh)
E x . 6 What will be conductance of pure silicon crystal at 300K Temp.. If electron hole pairs per cm3 is 1.072 x 1010
at this Temp, n = 1350 cm2 / volt sec & P = 480 cm2 / volt sec
S o l .  = niee + nieh = n ie ( e + h) = 3.14×10–6 mho/cm
E x . 7 Pure Si at 300 K has equal electron ne and hole nh concentration of 1.5 × 1016/m3. Doping by indium increases
nh to 4.5 × 1022/m3. Calculate ne in doped silicon.
n 2i (1.5  10 16 ) 2
S o l . ne =  22
 5  10 9 m 3
nh (4.5  10 )
E 7
JEEMAIN.GURU
JEE-Physics
E x . 8 A semiconductor has equal electron and hole concentration of 6 × 108/m3. On doping with certain impurity
electron concentration increases to 9 × 1012/m3.
(i) Identify the new semiconductor obtained after doping.
(ii) Calculate the new hole concentration.
Sol. ni = 6 × 108/m3 and ne = 9 × 1012 /m3
(i) ne > ni so it is N-type semiconductor
n 2i 36  1016
(ii)  n 2i  nen h nh =  = 4 × 104 /m3
ne 9  1012
P - N JUNCTION
Technique s for maki ng P-N junct ion
(i) Alloy Method or Alloy Junction
Here a small piece of III group impurity like indium is placed over n–Ge or n–Si and melted as shown in figure
ultimetely P – N junction form.
indium buttom PN J
n
indium indium liquid
N-type N-type N-type
n
arsenic buttom PN J
arsenic arsenic liquid
P-type P-type P-type
(ii) Diffusion Junction

vacuum n
A heated P–type semiconductor is kept in pentavalent heat N-type Ge/Si P-N J
impurity vapours which diffuse into P–type semiconductor as

Al
shown and make P–N junction. vapours diffused
(iii) Vapour deposited junction or epitaxial junction P-type layer
If we want to grow a layer of n–Si or p–Si then p–Si wafer is
kept in an atmosphere of Silane (a silicon compound which to vacuum
dissociates into Si at high temperatures) plus phosphorous pump
vapours. On craking of silane at high temperature a fresh layer on n–Si grows on p–Si giving the "P–N
junction". Since this junction growth is layer by so it is also referred as layer growth or epitaxial junction formation
of P–N junction. – +
Description of P-N Junction without applied voltage or bias p n
Given diagram shows a P–N junction immediately after it is formed.
P region has mobile majority holes and immobile negatively
charged impurity ions.
N region has mobile majority free electrons and immobile positively

hole free electron
charged impurity ions.
deplition layer
Due to concentration difference diffusion of holes starts from P to N
density
charge
width (10)-6
side and diffusion of e– s starts N to P side.
Due to this a layer of only positive (in N side) and negative +
distance
(in P–side) started to form which generate an electric field (N to P –
intensity
electric
side) which oppose diffusion process, during diffusion magnitude of

field
electric field increases due to this diffusion it gradually decreased distance
and ultimately stopes.

Potential
Electric
The layer of immobile positive and negative ions, which have no
V0 = Potential
free electrons and holes called as depletion layer as shown in barrier
distance
diagram.
8
E
JEEMAIN.GURU
JEE-Physics
GOLDEN KEY POINTS
-6
• Width of depletion layer  10 m
(a) As doping increases depletion layer decreases
(b) As temperature is increased depletion layer also increases.
(c) P-N junction  unohmic, due to nonlinear relation between I and V.
• Potential Barrier or contact potential
G e  0.3 V Si  0.7 V
V 0.5
• Electric field, produce due to potential barrier E    E   105 V/m
d 10 6
This field prevents the respective majority carrier from crossing barrier region
DIFFUSION AND DRIFT CURRENT
(1) Diffusion current – P to N side (2) Drift current – N to P side
If there is no biasing diffusion current = drift current
So total current is zero
BEHAVIOUR OF P–N JUNCTION WITH AN EXTERNAL VOLTAGE APPLIED OR BIAS
Forward Bias
If we apply a voltage "V" such that P–side is positive and N–side V
VB
is negative as shown in diagram. P N
The applied voltage is opposite to the junction barrier potential.Due to
this effective potential barrier decreases, junction width also decreases,
so more majority carriers will be allowed to flow across junction. It means
the current flow in principally due to majority charge carriers and it is in
the order of mA called as forward Bias.
Reverse Bias V
VB
If we apply a voltage "V" such that P–side is negative and
P N
N–side is positive as shown in diagram.
The applied voltage is in same direction as the junction barrier potential. Due
to this effective potential barrier increase junction, width also increases, so no
majority carriers will be allowed to flow across junction.
Only minority carriers will drifted. It means the current flow in principally due to minority charge carriers and is
very small (in the order of µA). This bias is called as reversed Bias.
GOLDEN KEY POINTS

• In reverse bias, the current is very small and nearly constant with bias (termed as reverse saturation current).
However interesting behaviour results in some special cases if the reverse bias is increased further beyond a
certain limit, above particular high voltage breakdown of depletion layer started.
• Breakdown of a diode is of following two types :
(i) Zener breakdown (ii) Avalanche breakdown
E 9
JEEMAIN.GURU
JEE-Physics
Comparison between Forward Bias and Reverse Bias
Forward Bias Reverse Bias
P positive P negative
N negative N positive
P N P N
V V
+ – – +
1. Potential Barrier reduces 1. Potential Barrier increases.
2. Width of depletion layer decreases 2. Width of depletion layer increases.
3. P-N jn. provide very small resistance 3. P-N jn. provide high resistance
4 Forward current flows in the circuit 4. Very small current flows.
5. Order of forward current is milli ampere. 5. Order of current is micro ampere for Ge
or Neno ampere for Si.
6. Current flows mainly due to majority carriers. 6. Current flows mainly due to minority carriers.
7. Forward characteristic curves. 7. Reverse characteristic curve
V(volt)
r
if Reverse saturation
(mA) current
break down
voltage
knee
voltage
0
V(volt)
f Ir ( A)
8. Forward resistance 8. Reverse resistance
Vf Vr
Rf   100  Rr   10 6 
I f I r
9. Order of knee or cut in voltage 9. Breakdown voltage
Ge  0.3 V Ge  25 V
Si  0.7 V Si  35 V
Rr 3 Rr
Special point : Generally R = 10 : 1 for Ge = 10 4 : 1 for Si
f Rf
10
E
JEEMAIN.GURU
JEE-Physics
E x . 9 The resistance of p-n junction diode decreases when forward biased and increases when reverse biased.
Why?
S o l . When p-n junction is forward biased, the width of depletion layer decreases and the barrier potential is opposed
by the forward bias. In other words, potential barrier decreases. Hence the diffusion of holes and electrons
through the junction increases. Due to this, the diode current increases and hence resistance decreases.
When p-n junction is reverse biased, the barrier potential is supported and the width of depletion layer increases.
As a result of this, the diode current becomes almost zero as there is no diffusion of majority carriers (electrons
and holes) through the junction. Hence the resistance of the junction diode increases when reverse biased.
Ex.10 What is an ideal diode ? Draw the output waveform across the load resistor R, if the input waveform is
as shown in the figure.
+6V
-6V
S o l . An ideal diode has zero resistance when forward biased and infiniter resistance when it is reversed biased.
Output wave form is shown in fig.
+6V
0V
Ex.11A potential barrier of 0.5 V exists across a p-n junction (i) If the depletion region is 5 × 10–7 m wide. What is the
intensity of the electric field in this region ? (ii) An electron with speed 5×105 m/s approaches the p-n
junction from the n-side with what speed will it enter the p-side.
So l. : (i) Width of depletion layer L = 5 × 10–7 m V
E=
L
V 0.5 V
E  = 10 6 volt/m P N
L 5  10 7
1 1
(ii) Work energy theorm Mv 2i  eV  Mv 2f
2 2
Mv 2i  2eV
vf  = 2.7 × 105 m/s
Ex.12 Figure shows a diode connected to an external resistance and an e.m.f. Assuming that the barrier potential
developed in diode is 0.5 V1 obtain the value of current in the circuit in milliampere.
S o l . E = 45 V1R = 100  100
voltage drop across p-n junction = 0.5 V

effective voltage in the circuit V = 4.5 – 0.5 = 4.0 V
4.5V
V 4.0
current in the circuit I    0.04 A = 0.04 × 1000 mA = 40mA
R 100
Ex.13Differentiate zener and avalanche breakdown.
S o l . The difference between these two are as follows
E 11
JEEMAIN.GURU
JEE-Physics
Zener Break down Avalanche Break down
Where covalent bonds of depletion layer, its Here covalent bonds of depletion layers are bro
self break, due to high electric field of very ken by collision of "Minorities" which aquire
high Reverse bias voltage. high kinetic energy from high electric field of
very-very high reverse bias voltage.
This phenomena predominant This phenomena predominant
(i) At lower voltage after "break down" (i) At high voltage after breakdown
(ii) In P – N having "High doping" (ii) In P – N having "Low doping"
(iii) P – N Jn. having thin depletion layer (iii) P – N Jn. having thick depletion layer
Here P – N not demage paramanently Here P – N damage peramanentaly due to
"In D.C voltage stablizer zener phenomenan "Heating effect" due to abruptly increament of
is used". minorities during repeatative collisoins.
CHARACTERISTIC CURVE OF P-N JUNCTION DIODE

P N
P N
symbol
(0-1)V (0-10)V
+ –  
If (mA) Forward
+ mA 
A
bias curve
–  Vr (Volt)
+ D D O Vf (Volt)

I r ( A )
R R Reverse
– Rh  Rh bias curve
Forward bias Reverse bias
In forward bias when voltage is increased from 0V is steps and corresponding value of current is measured, the
curve comes as OB of figure. We may note that current increase very sharply after a certain voltage knee
voltage. At this voltage, barrier potential is completely eliminated and diode offers a low resistance.
In reverse bias a microammeter has been used as current is very very small. When reverse voltage is increased
from 0V and corresponding values of current measured the plot comes as OCD. We may note that reverse
current is almost constant hence called reverse saturation current. It implies that diode resistance is very high. As
reverse voltage reaches value VB, called breakdown voltage, current increases very sharply.
For Ideal Diode
in forward bias in reverse bias
R = 0
f R =
r 
'ON' switch 'OFF' switch
RECTIFIER
It is device which is used for converting alternating current into direct current.
12
E
JEEMAIN.GURU
JEE-Physics
Half wave rectifier
Secondry Voltage
S1 A S1 A
D D Input
A.C. Supply RL A.C. Supply RL
B B
S2 S2 Output
For positive half cycle For negative half cycle
During the first half (positive) of the input signal, let S1 is at positive and S2 is at negative potential. So, the PN
junction diode D is forward biased. The current flows through the load resistance R L and output voltage is
obtained.
During the second half (negative) of the input signal, S1 and S2 would be negative and positive respectively. The
PN junction diode will be reversed biased. In this case, practically no current would flow through the load
resistance. So, there will be no output voltage.
Thus, corresponding to an alternating input signal, we get a unidirectional pulsating output as shown.
Peak inverse voltage (PIV)
In half wave rectifier PIV = maximum voltage across secondary coil of transformer (V s)
= Peak value of output (Vm)

Full wave rectifier

When the diode rectifies the whole of the AC wave, it is called full wave rectifier. Figure shows the experiemental
arrangement for using diode as full wave rectifier. The alternating signal is fed to the primary a transformer. The
output signal appears across the load resistance RL.
D1 D1 Secondry Voltage
S1 S1 Input
B A B A
A. C. Supply A. C. Supply
RL RL D1 D2 D1 D2 D1 D2 D1
S2 S2
Output
For positive half cycle D2 For negative half cycle D2
During the positive half of the input signal :

Let S1 positive and S2 negative.

In this case diode D1 is forward biased and D2 is reverse biased. So only D1 conducts and hence the flow of
current in the load resistance RL is from A to B.
During the negative half of the input signal :
Now S1 is negative and S2 is positive. So D1 is reverse-biased and D2 is forward biased. So only D2 conducts and
hence the current flows through the load resistance RL from A to B.
It is clear that whether the input signal is positive or negative, the current always flows through the load resistance
in the same direction and full wave rectification is obtained.
E 13
JEEMAIN.GURU
JEE-Physics
Bridge Rectifier
D2
D1 Input
RL
D1,D4 D2,D3 D1,D4 D2,D3 D1,D4
D3 D4 Output
During positive half cycle During negative half cycle
D1 and D4 are forward biased  on switch D2 and D3 are forward biased  on switch
D2 and D3 are reverse biased  off switch D1 and D4 are reverse biased  offswitch
In bridge rectifier peak inverse voltage PIV = Vs = Vm

Form Factor
I rms E rms
F = I or E dc
dc
 
for full wave rectifier F = for half wave rectifier F =
2 2 2
Ripple and ripple factor

In the output of rectifier some A.C. components are present. They are called ripple & there measurement is given
by a factor known as ripple factor. For a good rectifier ripple factor must be very low.
Total output current
I rms = I 2 ac + I 2 dc Where Iac = rms value of AC component present in output
I ac I 2rms
Ripple factor r = I  r =  1 =
dc I 2dc F2 1
Pdc I2 R
Rectifier efficiency  = = 2 dc L
Pac I rms (R F + R L )
Half wave rectifier Full wave rectifier or bridge wave rectifier
0.406 0.812
 = 
R R
1 f 1 f
RL RL
Rf Rf
If R < < 1 , then  = 40.6% If R < < 1 , then   81.2%
L L
Special Note If Rf = RL Special Note If Rf = RL

  20.3%   40.6%
Note : In brige full wave rectifier Rf is two times of resistance of P-N jn. diode in FB.
14
E
JEEMAIN.GURU
JEE-Physics
Ripple Frequency
(i) For half wave rectifier
input output
input frequency = 50Hz ripple frequency = 50Hz
(ii) for full wave rectifier
input output
input frequency = 50Hz ripple frequency = 100Hz
Pulse
(i) For half wave rectifier
input output
Pulse frequency = 100 Hz Pulse frequency = 50 Hz
(ii) For full wave rectifier
input output
Pulse frequency = 100 Hz Pulse frequency = 100 Hz
Comparison Between Average Rectifiers
Full-wave
Half-wave C e n t re - t a p Bridge
Number of Diodes 1 2 4
Transformer necessary No Yes No
Peak secondary voltage Vs Vs Vs
Peak Inverse Voltage Vs = V m V s = 2V m V s = V m
(when peak of output = Vm)
Vin Vin Vin

Peak load Current, Im rd  R L rd  R L 2rd  R L
Im Im Im
RMS Current, Irms
2 2 2
Im 2 Im 2 Im
DC current, Idc
  
Ripple factor, r 1.21 0.482 0.482

Rectification efficiency (max) 40.6% 81.2% 81.2%
Ripple frequency (when input = 50 Hz) 50 Hz 100 Hz 100 Hz
E 15
JEEMAIN.GURU
JEE-Physics
E x . 1 4 A sinusoidal voltage of amplitude 25 volts and frequency 50 Hz is applied to a half wave rectifier using
PN diode. No filter is used and the load resistor is 1000  . The forward resistance R f ideal diode is
10  . Calculate
(i) Peak, average and rms values of load currrent.
(ii) d.c. power output (iii) a.c. power input
(iv) % Rectifier efficiency (v) Ripple factor
Vm 25
S o l . (i) m  
R f  R L (10  1000) = 24.75 mA
 m 24.75
 dc    7.88mA
 3.14
 24.75
 rms  m   12.38mA
2 2
2 –3 2 3
(ii) Pdc = I dc × R L = (7.88 × 10 ) × 10  62 mW
2 –3 2
(iii) P ac = I rms (R f + R L ) = (12.38 × 10 ) × (10 + 1000)
 155 mW
Pdc
(iv) Rectifier efficiency  = P × 100
ac
62
= × 100 = 40 %
155
1/2
 I 2   12.38  2 
rms
(v) 
Ripple factor =  I   1  =  7.88   1  = 1.21
 ac    
Ex.15 The halfwave rectifier supplies power to a 1 k load. The input supply voltage is 220 V neglecting forward
resistance of the diode, calculate
(i) V dc
(ii) dc and
(iii) Ripple voltage (rms value)
Vm 2 Vrms 2  220
S o l . (i) Vdc     99 volt
  3.14
V 99
(ii)  dc  dc   99 mA
R L 1000
(Vr ) rms
(iii) r =
Vdc
or (V r ) rms = r × v dc = 1.21 × 99 = 119.79 volt.
Ex.16 A fullwave rectifier supplies a load of 1 K  . The a.c. voltage applied to the diodes is 220 volt rms. If
diode resistance is neglected, calculate.
(i) Average d.c. voltage (ii) Average d.c. current (iii) Ripple voltage (rms)
2Vm
S o l . (i) Average d.c. voltage V dc = = 0.636 V m

where V m = maximum across each half of the secondary winding.
Vm
If V be the rms voltage across each half of the secondary winding then V 
2
 V dc = 0.636 × V 2 = 0.9 V
= 0.9 × 220 = 198 volt.
Vdc 198
(ii) For fullwave rectifier I dc = R = = 198 mA
L 1000
Vr ( rms )
(iii) r =  V r(rms) = r × V dc  V r(rms) = 0.482 × 198 = 95.436 volt
Vdc
16
E
JEEMAIN.GURU
JEE-Physics
Ex.17 A fullwave P.N. diode rectifier used load ressitor of 1500  . No filter is used. Assume each diode to have
idealized charcteristic with R f = 10  and R r = . Since wave voltage applied to each diode has amplitude
of 30 volts and frequency 50Hz. Calculate.
(i) Peak, d.c. rms load current
(ii) d.c. power input

(iii) A.C. power input
(iv) Rectifier efficiency

Vm
S o l . (i) Peak current I m =
Rf  RL
30volts
I m = = 19.9 mA
10  1500
2Im
d.c. load current I dc = = 0.636 I m

= 0.636 × 19.9 mA = 12.66 mA.
 m 19.9
 rms =   14 mA
2 2
2
(ii) D.C. Power output P dc = I dc × R L
–3 2
= (12.66 × 10 ) × 1500 Watt = 240.41 mW
2
(iii) A.C. power input P in = I rms (R f + R 2 )
–3 2
= (14 × 10 ) (10 + 1500) watt = 295.96 mW
FILTER CIRCUIT
To reduce A.C. Components
Capacitor Filter
DC
AC + DC
AC C RL
output of rectifier output
L - C Filter
DC + low AC DC
AC + DC
AC C RL
 - Filter (Best Filter)

DC + low AC
DC
AC + DC
AC C1 AC C2 RL
approx pure D.C
E 17
JEEMAIN.GURU
JEE-Physics
ZENER DIODE
A specifically doped crystal diode which can work in break down region is known as Zener diode.
It is always connected in reverse biased condition manner. +
Used as a voltage regulator RS
+ Fluctuating regulated
Symbol of RL
 input output
Zener diode
In forward biased it works as a simple diode. 

Voltage regulating circuit of Zener diode
SOME OTHER SPECIAL DIODES

Photodiode
A junction diode made from “light or photo sensitive semiconductor” is called a “photo diode” its symbol .
When light of energy "h'' falls on the photodiode (Here h > energy gap) more electrons move from valence
band, to conduction band, due to this current in circuit of photodiode in "Reverse bias", increases. As light
intensity is increased, the current goes on increases so photo diode is used, "to detect light intensity" for example
it is used in "Vedio camera".
Light emitting diode (L.E.D)
When a junction diode is “forward biased” energy is released at junction in the form of light due to recombination
of electrons and holes. In case of Si or Ge diodes, the energy released is in infra-red region.
In the junction diode made of GaAs, InP etc energy is released in visible region such a junction diode is called
"light emitting diode" (LED) Its symbol
Solar cell
Solar cell is a device for converting solar energy into electrical. A junction diode in which one of the P or N
sections is made very thin (So that the light energy falling on diode is not greatly asorbed before reaching the
junction) can be used to convert light energy into electric energy such diode called as solar cell. Its symbol
(i) It is operated into photo voltaic mode i.e., generation of voltage due to the bombardment of optical
photon.
(ii) No external bias is applied.
(iii) Active junction area is kept large, because we are intrested in more power. Materials most commonly
used for solar cell is Si, As, Cds, CdTe, CdSe, etc.
Variable capacitor (Varactor)
P – N junction diode can be used as a "Capacitor" here depletion layer acts as "dielectric material" and remaining
"P" and "N" part acts as metallic plates.
  its symbol 
Diode laser
It is intersting form of LED in which special construction helps to produce stimulated radiation as in laser.
18
E
JEEMAIN.GURU
JEE-Physics
E x . 1 8 A zener diode of voltage VZ (=6V) is used to maintain a constant voltage across a load resistance RL (=1000)
by using a series resistance R S (=100). If the e.m.f. of source is E (= 9 V), calculate the value of current
through series resistance, Zener diode and load resistance. What is the power being dissipated in Zener
diode.
S o l . Here, E = 9V ; V Z = 6V ; R L = 1000 and R S = 100,
Potential drop across series resistor VR = E – VZ = 9 – 6 = 3 V
VR 3
Current through series resistance RS is     0.03A
R 100
VZ 6
Current through load resistance RL is  L    0.006 A
R L 1000
Current through Zener diode is I Z = I - I L = 0.03 - 0.006 = 0.024 amp.
Power dissipated in Zener diode is P Z = V Z I Z = 6 x 0.024 = 0.144 Watt
Ex.19 A Zener diode is specified having a breakdown voltage of 9.1 V with a maximum power dissipation of
364 mW. What is the maximum current that the diode can handle.
364  10 3
S o l . Maximum current that the given diode can handle is A i.e., 40 mA.
9.1
TRANSISTOR
Inventor William Bradford Shockley, John Bardeen and Walter Houser Brattain.
Transistor is a three terminal device which transfers a singal from low resistance circuit to high resistance circuit.
It is formed when a thin layer of one type of extrinsic semiconductor (P or N type) is sandwitched between two
thick layers of other type of extrinsic semiconductor.
Each transistor have three terminals which are :-
(i) Emitter
(ii) Base
(iii) Collector
Emitter : It is the left most part of the transistor. It emit the majority carrier towards base. It is highly doped and
medium in size.
Base : It is the middle part of transistor which is sandwitched by emitter (E) and collector (C). It is lightly doped
and very thin in size.
Collector : It is right part of the transistor which collect the majority carriers emitted by emitter. It has large size
and moderate doping.
There are two semiconducting PN-junctions in a transistor
(i) The junction between emitter and base is known as emitter-base junction (J EB ).
(ii) The junction between base and collecter is known as base-collector junction (J CB).
E 19
JEEMAIN.GURU
JEE-Physics
TRANSISTOR ARE OF TWO TYPES
N-P-N Tra nsistor
If a thin layer of P-type semiconductor is sandwitched between two thick layers of N-type semiconductor is
known as NPN transistor.
NPN
E N P N C
E C
B B
P-N-P Tra nsistor

If a thin layer of N-type of semiconductor is sandwitched between two thick layer of P-type semiconductor is
known as PNP transistor.
PNP
E P N P C
E C
B B
GOLDEN KEY POINTS
• Transistor have two P-N Junction JEB and JCB, therefore it can be biased in four following ways as given below:
E N P N C
B
Emitter-Base Collector-Base Region of working
Forward biased Reverse biased Active
Reverse biased Forward biased Inverse Active
Reverse biased Reverse biased Cut off
Forward biased Forward biased Saturation
• Comparsion between E, B and C
Emitter Medium size High dopping
Base Smallest size Low dopping
Collector Largest size Medium dopping
• The collector region is made physically larger than the emitter. Because collector has to dissipiate much
greater power.
• Transistor all mostly work in active region in electronic devices & transistor work as amplifier in Active region
only.
• Transistor i.e. It is a short form of two words "Transfer resistors". Signal is introduced at low resistance circuit
and out put is taken at high resistance circuit.
• Base is lightly doped. Otherwise the most of the charge carrier from the emitter recombine in base region and
not reaches at collector.
• Transistor is a current operated device i.e. the action of transistor is controlled by the motion of charge
carriers. i.e. current
20
E
JEEMAIN.GURU
JEE-Physics
WORKING OF NPN TRANSISTOR
The emitter Base junction is forward bias and collector base junction is reversed biased of n-p-n transistor in
circuit (A) and symbolic representation is shown in Figure.
emitter-base collectoremitter-base
junction junction
N P N IE IC
IE e IC
h
B VEE IB VCC
mA E C mA
VEE IB VCC
When emitter base junction is forward bias, electrons (majority carriers) in emitter are repelled toward base.
The barrier of emitter base junction is reduced and the electron enter the base, about 5% of these electron
recombine with hole in base region result in small current (Ib).
The remaining electron (  95%) enter the collector region because they are attracted towards the positive
terminal of battery.
For each electron entering the positive terminal of the battery is connected with collector base junction an
electron from negative terminal of the battery connected with emitter base junction enters the region.
The emitter current (Ie) is more than the collector (Ic).
The base current is the difference between Ie and Ic and proportional to the number of electron hole recombination
in the base.
Ie = Ib +Ic
WORKING OF PNP TRANSISTOR
When emitter-base junction is forward biased holes (majority carriers) in the emitter are repelled towards the
base and diffuse through the emitter base junction. The barrier potential of emitter-base junction decreases and
hole enter the n-region (i.e. base). A small number of holes (  5%) combine with electron of base-region resulting
small current (Ib). The remaining hole (  95%) enter into the collector region because they are attracted towards
negative terminal of the battery connected with the collector-base junction. These hole constitute the collector
current (Ic).
emitter-base collectoremitter-base
junction junction
P N P IC IC
IE
VEE IB VCC
mA E B C mA
+
VEE IB VCC
As one hole reaches the collector, it is neutralized by the battery. As soon as one electron and a hole is
neutralized in collector a covalent bond is broken in emitter region. The electron hole pair is produced. The
released electron enter the positive terminal of bettary and hole more towards the collector.
E 21
JEEMAIN.GURU
JEE-Physics
Basic Tra nsistor Circuit Configurat ions :-
To study about the characterstics of transistor we have to make a circuit [In which four terminals are required.
But the transistor have three terminals, so one of the terminal of transistor is made common in input and output
both. Thus, we have three possible configuration of transistor circuit.
(i) Common base configuration (ii) Common emitter configuration (iii) Common collector configuration
In these three common emitter is widely used and common collector is rarely used.
Common emitter characterstics of a transistor
Circuit Diagram :
R1
R2
( ) ( )
Circuit diagram for characteristic curve of n-p-n transistor in CE mode
Input characterstics
input characteristic curves
The variation of base current (Ib) (input) with base emitter voltage (VEB)
V
V
Vc = 5
V e =0
at constant-emitter voltage (VCE) is called input characterstic. 100
e
c
75
(i) Keep the collector-emitter voltage (VCE) constant (say VCE = 1V)
50
I (A)
(ii) Now change emitter base voltage by R1 and note the corresponding
25
b
value of base current (Ib).
0
(iii) Plot the graph between VEB and Ib. 0.2 0.4 0.6 0.8 0.8
(iv) A set of such curves can be plotted at different (VCE = 2V) Vbe(volt)
Output characterstics
0A
The variation of collector current Ic (output) with collector-emitter Ib = 10
10
Ib = 75A
voltage (VCE) at constant base current (Ib) is called output characterstic. 8
6 Ib = 50A
IC(mA)
(i) Keep the base current (Ib) constant (say Ib = 10A)
4 Ib = 25 A
(ii) Now change the collector-emitter voltage (VCE) using variable resistance R2 and
2 Ib =0
note the corresponding values of collector current (Ic).
1 2 3 4 5
(iii) Plot the graph between (VCE versus Ic) VCE(volt) E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Electronics\Eng\1. Electronics-Semi Conductor Theory.p65
(iv) A set of such curves can be plotted at different fixed values of base current (say 0, 20 A, 30 A etc.)
TRANSISTOR AS AN AMPLIFIER
The process of increasing the amplitude of input signal without distorting its wave shape and without changing
its frequency is known as amplification.
A device which increases the amplitude of the input signal is called amplifier.
A transistor can be used as an amplifier in active state.
A basic circuit of a common emitter transistor amplifier is shown.
22
E
JEEMAIN.GURU
JEE-Physics
IC
–
C
B
RL
intput IB
signal E V Vo amplifier
CE
Vi +
IE amplified
VCC
– output signal
IB IC
+
+ –
VBB
common emitter amplifier
NPN transistor
Comparative study of transistor configurations

1. Common Base ( C B ) 2. Common Emitter (CE) 3. Common Collector (CC)
C B C E C C
E C B C B E
CB CE CC
B B E E C C
IE IC C E
IC IE
B B
IB IB
IB IE IC
B B E E C C
Input Resistance Low (100  ) High (750  ) Very High  750 k

Output resistance Very High High Low
Current Gain (AI or ) (AI or ) (AI or )
IC IC IE
 = I   = I   = I 
E B B
Vo IC R L Vo IC R L Vo IE R L
Voltage Gai n AV  = A V  V = I R AV  =
Vi IE R i i B i Vi IB R i
RL RL RL
A v =  A v =  A v = 
Ri Ri Ri
  less than 1
Po Po Po
Power Gain Ap  Ap  Ap 
Pi Pi Pi
RL 2 RL RL
A p  2 A p   R A p  2
Ri i Ri
Phase difference same phase opposite phase same phase

(between output
and input)
Application For High Fequency For Audible fequency For Impedance Matching
E 23
JEEMAIN.GURU
JEE-Physics
Relation Between    and  
      
IE = IB + IC IE = IB + IC --
divide by IC divide by IB


  1+
1-
IE I IE I 1
 B 1  1+ C 
IC IC IB IB 1-
1 1
 +1 
 


1-
GOLDEN KEY POINTS

• In transistor charge carriers move from emitter to collector. Emitter send the charge carriers and collector
collect them this happen only when emitter-base junction is forward bias and collector-base junction is reverse
bias (base of amplifier)
• In transistor reverse bias is high as compared to forward bias so that the charge carriers move from emitter to
base exert a large attractive force to enter in collector region so base current is very less.
• CE configuration is widely used becasue it have large voltage and power gain as compared to other amplifiers.
• In amplifier negative feed back is used to stabilized the gain.
• CC is used for impdence matching for connecting two transistors in cascade.
Q . 2 0 A transistor is a current operated device. Explain why ?
A n s . The action of a transistor is controlled by the charge carriers (electrons or holes). That is why a transistor is a
current operated device.
Q . 2 1 In a transistor, reverse bias is quite high as compared to the forward bias. Why ?
A n s . In a transistor, charge carriers (electrons or holes) move from emitter to collector through the base. The reverse
bias on collector is made quite high so that it may exert a large attractive force on the charge carriers to enter
the collector region. These moving carriers in the collector constitute a collector current.
Q . 2 2 A transistor is a temperature sensitive device. Explain. E:\Data\2014\Kota\JEE-Advanced\SMP\Phy\Electronics\Eng\1. Electronics-Semi Conductor Theory.p65
A n s . In a transistor, conduction is due to the movement of current carriers electrons and holes. When temperature of
the transistor increases, many covalent bonds may break up, resulting in the formation of more electrons and
holes. Thus, the current will increase in the transistor. This current gives rise to the production of more heat
energy. the excess heat causes complete breakdown of the transistor.
Q . 2 3 The use of a transistor in common-emitter configuration is preferred over the common-base configuration.
Explain why ?
A n s . The current gain and hence voltage gain in the common-emitter configuration is much more than i of common-
base configuration. Hence the former is preferred over the later.
24
E
JEEMAIN.GURU
JEE-Physics
Q . 2 4 Why do we prefer transistor over the vacuum tubes in the portable radio receivers ?
A n s . This is because of two reasons :
(i) Transistor is compact and small in size than the vacuum tube.
(ii) Transistor can operate even at low voltage which can be supplied with two or three dry cells.
Q . 2 5 Why a transistor cannot be used as a rectifier ?
A n s . If transistor is to be used as a rectifier the either emitter-base or base-collector has to used as diode. For equated
working of the said set of diodes, the number density of charge carriers in emitter and base or base and collector
must be approximately same. As base is lightly doped and comparatively thin, so emitter cannot work as a
rectifier.
Ex.26 In a transistor, the value of  is 50. Calculate the value of .
  50
S o l .  = 50   50 =  50 – 50  =    = 0.98
1 1 51
Ex.27 Calculate the collector and emitter current for which Ib = 20 A,  = 100
S o l .  = 100, Ib = 20 A
Ic =  Ib = 100 × 20 × 10–6 = 2000 A
Ie = Ib + Ic = 20 + 2000 = 2020 A = 2.02 × 10–3 A = 2.02 mA
Ex.28 For a common emitter amplifier, current gain = 50. If the emitter current is 6.6 mA, calculate the collector and
base current. Also calculate current gain, When emitter is working as common base amplifier.
S o l . = 50 ; Ie = 6.6 mA
Ic
   Ic = Ib = 50Ib ...(i)
Ib
Ie = Ic + Ib using equation (i) we get 6.6 = 50 Ib + Ib = 51Ib
6.6
or Ib  = 0.129 mA
51
6.6  50
HenceIc = 50 × = 6.47 mA and  =  0.98
51 1 51
Ex.29 Transistor with  = 75 is connected to common-base configuration. What will be the maximu collector current
for an emitter current of 5 mA ?

S o l .  = 75, Ie = 5 mA
 
   75 =  75 – 75 = 
1 1
75
or 76 = 75 or  =
76
Ic 75
  Ic = Ie = × 5 = 4.93 mA
Ie 76
E 25
JEEMAIN.GURU
JEE-Physics
Ex.30 The base current is 100 A and collector current is 3 mA.
(a) Calculate the values of , Ie and 
(b) A change of 20 A in the base current produces a change of 0.5 mA in the collector current. Calculate
 a.c..
S o l . Ib = 100 A = 0.100 mA, Ic = 3 mA
Ic 3
(a)  = = 30
Ib 0.100
 30 30 I c 3  31
   = 0.97 and Ie =  = 3.1 mA
1   1  30 31  30
(b) Ib = 20 A = 0.02 mA , Ic = 0.5 mA
I c 0.5
 ac    25
I b 0.02
Ex.31 In npn transistor circuit, the collector current is 10 mA. If 95% of the electrons emitted reach the collector, what
is the base current ?
S o l . I c = 95% Ic = 0.95 Ie
100 100
 Ie =  Ic   10mA = 10.53 mA ( Ic = 10 mA)
95 95
Now Ie = Ic + Ib  Ib = Ie – Ic = 10.53 – 10 = 0.53 mA

Ex.32 In an NPN transistor 1010 electrons enter the emitter in 10–6 s and 2% electrons recombine with holes in base,
then current gain  and  are :
Ne 1010  1.6  10 19

S o l . Emitter current Ie = = = 1.6 mA
t 10 6
2
Base current Ib =  1.6 = 0.032 mA
100
but Ie = Ic + Ib  Ic = Ie – Ib = 1.6 – 0.032 = 1.568 mA
I c 1.568
     0.98
Ie 1.6
I c 1.568
and    49
I b 0.032
FEEDBACK
Feedback are two types :

Positive feedback
When input and output are in the same phase then positive feedback is there. It is used in oscillators.
Negative feedback
If input and output are out of phase and some part of that is feedback to input is known as negative feedback.
It is used to get constant gain amplifier.
26
E
JEEMAIN.GURU
JEE-Physics
TR ANSISTOR AS AN OSCILL ATOR
Oscillator is device which delivers a.c. output wave form of desired frequency from d.c. power even without
input singal excitation.
T1
The electric oscillations are produced by L– C circuit 1
2
mutual inductance
(i.e. tank circuit containing inductor and capacitor). These (coupling through
3 magnetic field)
oscillations are damped one i.e. their amplitude decrease
C T2
with the passage of time due to the small resistance of the T'2 output
n-p-n L
inductor. In other words, the energy of the L – C oscillations 4
decreases. If this loss of energy is compensated from outside,


then undamped oscillations (of constant amplitude) can be S1 (switch)
obtained.
This can be done by using feed back arrangement and a
transistor in the circuit.
L – C circuit producing L – C oscillations consists of an inductor of inductance L and capacitor of
variable capacitance C inductor of inductance L' is connected in the collector-emitter circuit through a battery
and a tapping key (K). Inductors L and L' are inductively coupled (Figure)
Wo r k i n g
When key K is closed, collector current begins to flow through the coil L. As this current grows, magnetic flux
linked with coil L increase (i.e. changes).
Since coil L is inductively coupled with L, so magnetic flux linked with coil L' also changes. Due to change in
magnetic flux, induced e.m.f. is set up across the coil L'.
The direction of induced e.m.f. is such that the emitter-base junction is forward biased. As a result of this biasing,
emitter current Ie increases which in turn increases the collector current Ic [ Ie = Ib + Ic].
With the increase in collector current, magnetic flux linked with coil L also increases. This increases the e.m.f.
induced in the coil L'.
The increased induced e.m.f. increases the forward bias of emitter-base junction. Hence emitter current is
further increased which in turn increases the collector current. The process of increasing the collector current
continues till the magnetic flux linked with coil L' becomess maximum (i.e. constant). At this stage, the induced
e.m.f. in coil L' becomes zero.
The upper plate of the capacitor C gets positively charged during this process.
When induced e.m.f. becomes zero, the capacitor C starts discharging through the inductor L.
The emitter current starts decreasing resulting in the collector current. With decreasing collector current which
flows through L', e.m.f. is again induced in the coil L' but in the opposite direction. It opposes the emitter current
and hence collector current ultimately decreases to zero.
The change in magnetic flux linked with coil L' stops and hence induced e.m.f. in the coil L becomes zero. At this
stage, the capacitor gets discharged through coil L but now in the opposite direction. Now the emitter current
and hence collector current increase but now in the opposite direction .
This process repeats and the collector current oscillates between maximum and minimum values.
1
f
2  LC
E 27
JEEMAIN.GURU
JEE-Physics
ADVANTAGES OF SEMICONDUCTOR DEVICES OVER VACUUM TUBES
Advantages
 Semiconductor devices are very small in size as compared to the vacuum tubes. Hence the circuits using
semiconductor devices are more compact.
 In vacuum tubes, current flows when the filament is heated and starts emitting electrons. So, we have to wait for
some time for the operation of the circuit. On the other hand, in semiconductor devices no heating is required
and the circuit begins to operate as soon as it switched on.
 Semiconductor devices require low voltage for their operation as compared to the vacuum tube. So a lot of
electrical power is saved.
 Semiconductor devices do not produce any humming noise which is large in case of vacuum tube.
 Semiconductor devices have longer life than the vacuum tube. Vacuum tube gets damaged when its filament is
burnt.
 Semiconductor devices are shock proof.
 The cost of production of semiconductor-devices is very small as compared to the vacuum tubes.
 Semiconductor devices can be easily transported as compared to vacuum tube.
Disadvantages
 Semiconductor devices are heat sensitive. They get damaged due to overheating and high voltages. So they
have to be housed in a controlled temperature room.
 The noise level in semiconductor devices is very high.
 Semiconductor devices have poor response in high frequency range.
Q . 3 3 Why is a transistor so called ?
A n s . The word Transistor can be treated as short form of two words 'transfer resistor'. In a transistor, a signal is
introduced in the low resistance circuit and output is taken across the high resistance circuit. Thus, a transistor
helps to transfer the current from low resistance part to the high resistance part.
Q . 3 4 The base region of a transistor is lightly doped. Explain why ?
A n s . In a transistor, the majority carriers (holes or electrons) from emtter region move towards the collector region
through base. If base is made thick and highly doped, then majority of carriers from emitter will combine with
the carriers in the base and only small number of carriers will reach the collector. Thus the output or collector
current will be considerably small. To get large output or collector current, base is made thin and lightly doped
so that only few electron-hole combination may take place in the base region.
Q . 3 5 Explain why the emitter is forward biased and the collector is reverse biased in a transistor ?
A n s . In a transistor, the charge carriers move from emitter to collector. The emitter sends the charge carriers and
collector collects them. This can happen only if emitter is forward biased and the collector is reverse biased so
that it may attract the carriers.
28
E

1 Electronics Semi Conductor Theory Jeemain - Guru

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

1 Electronics Semi Conductor Theory Jeemain - Guru

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1 Electronics Semi Conductor Theory Jeemain - Guru

Uploaded by

Copyright:

Available Formats

JEEMAIN.

SEMI CONDUCTOR - ELECTRONICS

Based on Pauli's exclusion principle

Valence Ba nd (VB)

(a) Have bonded electrons.

(b) No flow of current due to such electrons.

(c) Always fulfill by electrons.

Conduction Band (CB)

(a) It has conducting electrons.

(b) Current flows due to such electrons.

(d) Electrons may exist or not in it.

Forbidden Energy gap (FEG) (Eg)

 Eg = (C B)min – (V B)max

CL ASSIFICATION OF CONDUCTORS, INSUL ATORS AND SEMICONDUCTOR : -

Compari son bet ween conductor, semiconductor a nd i nsulator :

Conductor Semi conductor Insulator

Forbidden energy gap  0eV  1eV  3eV

CONCEPT OF "HOLES" IN SEMICONDUCTORS

• It is deficiency of electron in VB.

• It's effective mass is more than electron. Si Si Si Si

• It's mobility is less than electron.

GOLDEN KEY POINTS

At absolute zero kelvin temperature Above absolute temperature

EFFECT OF IMPURITY IN SEMICONDUCTOR

Intrinsic Semiconductor N-type (Pentavalent impurity) P-t ype(Trivalent impurit y)

6. Entirely neutral Entirely neutral Entirely neutral

Mass action Law

so rate of recombination = R ne × nh R = recombination coefficient,

For intrinsic semiconductor ne = nh = ni

so rate of recombination = R ni2

R ne × nh = R ni2  ni2 = ne × nh

Thus from mass action law n e  n h  n 12

12400 E 2.1  1.6  10 19 J

S o l . In pure semiconductor electron-hole pair ni = 1019 m–3

acceptor impurity N A = 10 21 m –3

Holes concentration nh = 1021 m–3

Conduction in conductor

Conduction in Semiconductor

Intrinsic semiconductor P - type N - type

ne = nh n h >> n e n e >> n h

J = ne [ ve + vh] J  e nh vh J  e ne ve

GOLDEN KEY POINTS

• Due to impurity the conductivity increases approximately 105 times

S o l .  = niee + nieh = n ie ( e + h) = 3.14×10–6 mho/cm

indium indium liquid

N-type N-type N-type

P-type P-type P-type

(ii) Diffusion Junction

impurity vapours which diffuse into P–type semiconductor as

N region has mobile majority free electrons and immobile positively

side) which oppose diffusion process, during diffusion magnitude of

and ultimately stopes.

DIFFUSION AND DRIFT CURRENT

If there is no biasing diffusion current = drift current

So total current is zero

majority carriers will be allowed to flow across junction.

GOLDEN KEY POINTS