PARUL POLYTECHNIC INSTITUTE FABRICATION TECHNOLOGY

MECHANICAL ENGINEERING 3361905

CHAPTER - 1

1. Describe the importance of Fabrication Technology 2

ઉ ોગોમાં ફ ીકશન ટ નોલો ની જ રયાત સમ વો.
2. List any four name of Fabrication industries field 2
ફ ીકશન ઇ ડ ઝ ફ ડના કોઈ પણ ચાર નામ આપો.
3. List any four power sources for welding. 2

4. List the Application of Fabrication work. 2

ફ ીકશન વક ના ઉપયોગો જણાવો.
5. List the third party inspection agencies. 2
કોઈ પણ ચાર થડ પાટ ઇ પેકશન એજસી ં ના નામ આપો.
6. Describe application of Power sources for welding process. 3
પાવર સોસ ના ઉપયોગો જણાવો.
7. Explain concept of weld ability. 3
વેલડ બ લટ નો સામા ય યાલ આપો.
8. List the factors affecting on weld ability 3
વેલડ બ લટ ને અસર કરતા પ રબળો જણાવો.
9. State Advantages and limitations of Power sources for welding process. 3
વે ડગ ોસેસ માટ પાવર સોસ ના ફાયદા અને મયાદા જણાવો.
10. Explain the need & importance of Quality Control in fabrication work. 4
11. State selection criteria of power sources for welding. 4
વે ડગ માટના પાવર સોસ ની પસંદગી ના માપદં ડો જણાવો.

CHAPTER - 2

1. Draw any four piping symbols with the nomenclature. 2

2. Draw any four types of welding joints with the nomenclature. 2
3. Write full name of WTP and WPS. 2
4. Write various welding positions. 2
5. Draw sketch for any three edge preparation for welding. 3
6. Explain Welder Performance Qualification. 3
7. Explain Welding Procedure Specification 3
8. Draw sketch for corner joint, edge joint and lap joint. 4
PARUL POLYTECHNIC INSTITUTE FABRICATION TECHNOLOGY
MECHANICAL ENGINEERING 3361905
9. Draw the diagrammatic layout for piping joints. 4
10. Draw the standard location of elements of welding symbols with help of sketch. 4
11. Explain Shop Weld Plan 4
12. Explain Weld Test Plan. 4
13. Write the basic types of welding joints and their applications. 4

14. Write the need and application area of different codes used in fabrication 4
industries?
CHAPTER - 3

1. Name four advance welding processes. 2

2. State application of Edge Preparation. 2
3. State four equipments of Gas Welding. 2
4. State parameters of Arc Welding 2
5. Explain Welding Automation. 3
6. List equipments and machines used for edge preparation. 3
7. Write fabrication steps for Heat Exchanger. 3
8. Write fabrication steps of pressure vessel. 3
9. Write safety norms for Arc Welding 3
10. Describe the electro beam welding with figure. 4
11. Explain need of Edge Preparation for welding joints 4
12. Explain need of welding safety 4
13. List the equipments & tools, used for Arc Welding. 4
14. List the equipments & tools, used for Gas Welding 4
15. List the method of relieving thermal stresses and explain any one method. 4
16. State name of Post-heating methods & explain any ONE 4
17. State names of Advance Welding method & explain any ONE 4
18. State names of Pre-heating method & explain any ONE 4
19. State need & application of Post-heating. 4
20. State need & application of Pre-heating. 4
21. State the advantages and applications of laser beam welding. 4
22. Write application and selection criteria of post weld heat treatment. 4
PARUL POLYTECHNIC INSTITUTE FABRICATION TECHNOLOGY
MECHANICAL ENGINEERING 3361905
23. Write safety norms for Gas Welding. 4

CHAPTER - 4

1. Define thermal distortion & state its types. 2

2. List any four Destructive Test. 2
3. State remedies for preparing defect free weld. 2
4. Write the defects& causes found in weld 2
5. Define Weld ability and describe its Importance. 3
6. Describe meaning of Good Weld Quality. 3
7. Describe the difference between Inspection & Testing of weld. 3
8. Explain the factors considered for Weld Quality. 3
9. List common weld defects. 3
10. State the factors affecting the Weld ability 3
11. Write the definition of thermal distortion, its causes and effect. 3
12. Write the reasons for incomplete joints and remedies for them. 3
13. State the importance of weld quality. 4
14. Write methods to control thermal distortion. 4
15. List the weld testing methods and explain any two of them 7
16. List various non destructive test and explain any two. 7

17. State considerable Inspection points of before welding, during welding & after 7
Welding process.

CHAPTER - 5

1. List the surface colour coating equipments and tools. 2

2. State methods of surface cleaning. 2
3. State surface preparation and finishing methods. 4
4. List equipments and machines used for edge preparation. 4
5. Explain sand blasting. 4
6. Describe surface colour coating by brush. 4