International Journal of Mechanical and Production

Engineering Research and Development (IJMPERD)

ISSN (P): 2249-6890; ISSN (E): 2249-8001
Vol. 9, Issue 4, Aug 2019, 11-22
© TJPRC Pvt. Ltd.

A REVIEW ON VARIOUS BEAM THEORY TECHNIQUES FOR DYNAMIC

ANALYSIS OF ROTATING LAMINATED SHAFTS

SHIVANAND & Dr. SHRAVANKUMAR B. KERUR

Department of Mechanical Engineering, Basaveshwar Engineering College, Bagalkot, Karanataka, India
ABSTRACT

The composite laminated shafts have wide ranging applications in various mechanical devices that include
cylindrical tubes used in the marine and automotive industries and centrifugal separators of helicopters.
Rotating laminated composite shafts are developed for the replacement of traditional metallic shafts. An efficient beam
theory technique is required to analyse the changing behaviour of the rotating laminated composites. In recent times
many of the beam theory techniques that have been proposed analysed the dynamics of the laminated shafts that are
rotating in nature. The present paper presents a comprehensive review based on beam theory techniques that include
Equivalent Modulus Beam Theory (EMBT), Simplified Homogenized Beam Theory (SHBT), Modified EMBT, Layer
wise Beam Theory (LBT), Timoshenko beam theory (TMBT), Euler-Bernoulli beam theory and Shear Deformation
Beam Theory (SDBT). From a review of these techniques, Layer wise Beam Theory (LBT), Timoshenko beam theory

Original Article
(TMBT) and Shear Deformation Beam Theory (SDBT) techniques have been proved to provide better performance than
other beam theory techniques in terms of critical speed, accuracy, natural frequencies, and stiffness. Moreover, this
paper makes a comparative analysis based on the technique used and their corresponding critical speeds.

KEYWORDS: Layer wise Beam Theory (LBT), Timoshenko BT (TMBT) & Shear Deformation BT (SDBT)

Received: Apr 23, 2019; Accepted: May 14, 2019; Published: Jun 14, 2019; Paper Id.: IJMPERDAUG20192

INTRODUCTION

In recent years, the composite laminated shafts are used in several mechanical devices such as: (Ghoneam
et al., 2011; Nezhad et al., 2017; Zorzi& Giordano, 1985). Composite material shafts developed to replace the
traditional metallic shafts have wide ranging usage and applications . Composite shafts have the various essential
characteristics like high strength compared to weight than metals which are traditionally enticing for use in rotating
systems and their applications (Banerjee et al., 2016; Yongsheng et al., 2013). When compared to the metallic
shaft, the composite laminated shaft has lower level of vibration, better ratio of the strength and weight and a long
service life. Also, these materials enable the designers the chance of gaining pre-decided performances such as the
attainment of critical speeds, by altercation of the diverse composite layers including the number and orientation of
layers (Fanmaleki, &Qatu, 2013; Jacquet-Richardet et al., 2011). These above mentioned advantages of composite
material shafts have led to several studies concentrating on the analysis of these shafts and their applications.
These studies have produced multiple dissimilar analysis of the dynamic performance of the composite laminated
shafts (Chang et al., 2004; Hosseini et al., 2009.

For rotating composite laminated shafts, internal damping is the most significant and a related to a metal
rotor (Singh & Gupta, 1996). A driveshaft of the tail rotor which is made of boron (or epoxy) was examined for the
rotating materials used in helicopter. (Zinberg and Symonds, 1970). The examination revealed the change in

www.tjprc.org SCOPUS Indexed Journal [email protected]

12 Shivanand & Dr. Shravankumar B. Kerur

shear-normal coupling and the coupling effects of bending and stretching with variation in stacking sequence, and modify
the frequency valuation . EMBT was used to estimate the critical speed by considering the shaft as a narrow edged circular
tube maintained at each ends (Dos Reis et al., 1987; Gupta & Singh, 1996; Jin et al., 2016; Montagnier & Hochard, 2013;
suna, 2014). The speed of the shaft was evaluated through estimation of the cure that represented the unbalanced results
obtained at the sub-critical zone. A model was developed based upon the methodical examinations of narrow layered
composite cylindrical tubes (Chatelet et al., 2000). Layer wise Beam Theory (LBT) was developed by considering a layer-
wise displacement field. The theory was also amplified to analyse the dynamic issues of composite rotor (Singh & Gupta,
1996; Qatu& Iqbal, 2010; Shahrjerdi&Yavari, 2018).

A framework has been proposed by Bert, (1993) for diagnosis of critical speeds and the consequences of
bending-twisting coupling of the composite shaft. In the stability analysis of the composite shaft the parameters considered
are finite elements and loads compressed axially. Timoshenko beam theory is used to design the laminated composite shaft
for this analysis (Chen &Peng, 1998; Rajasekaran. 2013). The shaft was designed as a Bresse-Timoshenko beam as Bresse-
Timoshenko theory includes shaft gyroscopics (Chang et al., 2004; Elishakoff et al., 2009). The variability nature of
composite drive shaft due to fluctuation in rotational speed and torque was studied by Kim & Bert (1993). Multiple narrow
shell theories were used by them to conduct the study. Coriolis and centrifugal forces were part of rotational effects. The
theory also referred dynamic instability areas for shafts through simple support while longer duration. Vibration
characteristics of the rotating composite shafts was studied by Chang et al., (2004). The model developed from that study
included gyroscopic effects, rotary inertia and the effects of coupling which were produce as a result of laminating the
composite layers. The shear deformation beam theories of first as well as higher orders were used to examine the frequency
analysis of FG beams having variable thresholds (Shufrin & Eisenberger, 2005; Simsek, 2010). There are various
researches presented the composite rotating shaft model using a first-order shear deformable beam theory (Kant & Gupta,
1988; Reddy, 1997; Zhu et al., 2012; Hajianmaleki & Qatu, 2012).

LITERATURE REVIEW

Various techniques were implemented for modelling of composite laminated shaft, with the aim of dynamic
analysis of composite rotors (Gupta, 2015). These techniques include EMBT, SHBT, Modified EMBT, LBT, TMBT,
Euler-Bernoulli beam theory and SDBT. Figure 1 shows that the various beam theory techniques used for composite
laminated shafts.

+
Figure 1: Various Beam Theory Techniques

EMBT & Modified EMBT

Zinberg & Symonds utilised EMBT for the study of critical speeds of anisotropic cylindrical shafts which rotated.
The study developed an analysis procedure for the composite shaft. The dynamical evaluation procedure was meant to be

Impact Factor (JCC): 7.6197 SCOPUS Indexed Journal NAAS Rating: 3.11
A Review on Various Beam Theory Techniques for Dynamic 13
Analysis of Rotating Laminated Shafts

carried out on the narrow edged shaft having internal damping. EMBT theory proposed by Gupta & Singh, (1996) analysed
the tubular composite shafts. The shafts were symmetric in structure. The analytical theory was also applicable to dynamic
rotor. However, the model based upon EMBT was found to be unsuitable for unsymmetric structures. Application of the
theory to all models of dynamic rotor can result in faulty performance prediction (Gayen, 2013). Study by Sino et al.,
(2008) focused on the rotating composite laminated shaft and its dynamic instability characteristics. The study proposed an
integrated finite element beam model while taking internal damping into account. This model measured the instability
threshold and natural frequencies. The study also evaluated the relationship between instability threshold and natural
frequencies of the shaft with the laminate matrics. The components of laminate matrics were fiber orientation, stacking
sequences, and transversal shear effect. It was found that laminate matrics had considerable impact on the instability
threshold of the shaft. The characteristics of stability for the composite shaft which is rotating in nature was studied by
Chen et al., (1997). The study scrutinised the shaft behaviour in relation to axially compressed load while considering the
finite element technique. EMBT was used to construct a Timoshenko shaft from the sample composite shaft with
laminations. The results were then compared with the other beam techniques. It was found that the stacking sequence, the
boundary conditions and the length-radius proportion affect the critical speed of the composite shaft having thin walls.
The study also examined the relationship between location of the disk and the rotational speed depending on stability of the
rotating shaft. Traditional buckling formulation was employed to examine the critical load bearing capacity of the rotating
shaft which has thin walls. Natural frequencies for composite tubular shafts were examined by Gubran& Gupta, (2005).
The study altered gyroscopic effects, EMBT with shear deformation, and rotary inertia for conduction of research.
The implications of stacking sequences on the shaft were considered for the study. As the end result of the study, various
coupling procedures were proposed by using composite materials. The study shows that the proposed modified EMBT
provides more simplicity and more efficient for dynamic rotor analysis of tubular composite shafts.

SHBT

Sino et al., (2006) investigated the dynamic instability analysis of both internal and external damping using
general homogenized beam theory. In this, natural damping is evaluated from the specific damping measurements of each
laminate layer. This method provides the benefit of being effective for any configuration of the composite wall. developed
SHBT was proposed by Sino et al., (2008) for analysing the rotating shaft which is damped internally. This technique
overcomes one of the major issues in EMBT. In EMBT, the symmetrical and balanced stacking sequences are
incorporated, without any considerations for the distance of composite layers from neutral axis. In this, the critical speed
attained by the algorithms is better than the EMBT and LBT in terms of instability thresholds.

A first and second-order Generalised Beam Theory (GBT) was proposed by Davies, (1998). The theory was
meant to solve the issues arising out of distortional buckling of cold-formed sections. The theory used finite element
modelling to get the desired results. Nevertheless, GBT will always provide the most sophisticated output. The segregation
of essential modes, in GBT also enables opportunities that are not available in other alternate approaches. Silvestre, (2007)
investigated and analysed the elastic buckling characteristics of Circular Hallow Section (CHS) using a generalized beam
theory. In this, the beam theory technique is used for adaptation by considering the specific criteria like cross-section
geometry. Also, in this theory, the kinematic relations of thin shells and the variance of strain energy are analysed as they
constituted the structural characteristics of the Circular Hallow Section. In addition, the study also examined a cluster of
shell-type deformation modes and modelling consists of torsion and axisymmetric deformation modes.

www.tjprc.org SCOPUS Indexed Journal [email protected]

14 Shivanand & Dr. Shravankumar B. Kerur

Layer Wise Beam Theory (LBT)

For examination and accurate estimation of delamination and interlaminar stress dispensation, layerwise laminate
theories are used. In case of anisotropic materials, the chances of reduction in transverse shear effects are negligible, and
hence in these cases the above mentioned theories are utilised. In a study by Singh and Gupta, (1996), EMBT and LBT
were analysed. The study produced mathematical model so as to analyse working procedure of composite rotor. A layer
wise theory was proposed by Lee, (2000) &Gubran, (2000) to examine free vibration. The theory evaluated delamination
based laminated beam. Sekhar&Srinivas, (2002) proposed vibration characteristics of slotted composite shafts using beam
theory techniques. Yongsheng et al., (2014) proposed a rotating thin-walled composite shaft using layerwise beam theory
with internal damping.

On dimensional layer-wise theory was suggested by Filippi& Carrera, (2016). For this theory contrived layers of
cross-sectional layers and higher-order zig-zag functions (Cho & Kim, 2001) were considered. Computational cost was
reduced by implementation of this improved theory. The new theory retained the precision of conventional layer-wise
theories. The proposed technique also attained the features of variable kinetic theories. Piecewise continuous power series
expansions of arbitrary order were carried out on the cross sectional area of the entire layout to achieve those above
mentioned features. Laminated and sandwich beams of small length to depth proportionate value were considered to
develop various other mathematical from this theory. The new approach has two major advantages. Stress distribution and
displacement over the cross-sectional area of the beam is even and accurate. The natural frequencies are also as precise and
reliable as that of conventional layer-wise theories.

Vibration characteristics of rotating composite shafts was analysed by Arab et al., (2017a). Equivalent Single
Layer Theory (ESLT) was used in that study. The study incorporated rotary inertia, gyroscopic and shear deformation
effects so as to examine the dynamic effects of the composite shaft. . The results demonstrated that shear-normal coupling,
stacking sequences and fiber orientations attained good effect on the dynamic characteristics composite shafts. Arab et al.,
(2017b) proposed a multi-layer finite element for rotating laminated shaft. The theory employed the mechanism of
layerwise and shaft theories. The theory considered the various characteristics of rotating composite shafts like, critical
speeds, natural frequencies and dynamic behaviour. In the dynamic analysis of rotating laminated shaft, the proposed
Layerwise Shaft Theory was found to be relevant and applicable Euler-Bernoulli’s shaft finite element formulation was
proposed by Arab et al., (2018) by applying Equivalent Single layer Theory (ESLT). The proposed formulation too focused
on the dynamic analysis of rotating shaft with laminations. The results of this method demonstrated that well in terms of
instability threshold and natural frequencies when compared to SHBT and EMBT.

Timoshenko Beam Theory (TBT)

The application of finite elements for the simulation of rotors models which is considered more important in last
few years. Nelson, (1980) proposed a model which uses the Timoshenko beam theory for developing shape functions
including transverse shear effects. The model consists of the effects of rotational and translational inertia, axial load and
shear deformation. A Timoshenko beam finite element model was suggested by Lien-Wen & Der-Ming, (1991).
The model focused on the natural rotating speeds of a composite shaft while varying the conditions and thinness ratios.
The study revealed the relationship between natural rotors’ speeds and conditions of rotating shafts. Rotary inertia and
shear deformation also affected the speed of natural rotors. The study also established the superiority of finite element
models in producing fine convergence and meticulous rotating shaft systems. The results produce more accurate finite

Impact Factor (JCC): 7.6197 SCOPUS Indexed Journal NAAS Rating: 3.11
A Review on Various Beam Theory Techniques for Dynamic 15
Analysis of Rotating Laminated Shafts

element model for rotating the dynamic shaft.

Eringen's nonlocal elasticity theory and TBT were employed by Wang et al., (2006) in the examination of elastic
buckling properties of micro and nano tubes. Another new model to evaluate the static and dynamic behaviors of the beams
which are functionally graded were suggested by Li, (2008). The model considered rotary inertia and shear deformation of
the graded beams. This study deduced Euler–Bernoulli, and Rayleigh beam theories through procedural analysis of
Timoshenko beam theory. A theory for laminated composite beams was proposed by Tessler et al., (2009) by considering
the kinematics properties of the Timoshenko Beam Theory. This provides a relatively accurate estimation of structural
response, low-cost, and high-performance aerospace structures.

Rao & Roy, (2016) proposed a dynamic analysis model for functionally graded (FG) rotor shaft system.
This theory utilized power-law gradation for material modelling. Timoshenko beam theory (TMBT) was employed for the
finite element modelling of FG rotor shaft. FG shaft model is confirmed that the good critical speed by considering rotary
inertia, strain, internal damping and shear deformation. An active magnetic bearing (AMB) aid rotors that use
electromagnetic force (EMF) instead of mechanical forces. Hence, exact prediction of the coefficient of AMB forces is
imperative as rotor dynamic analysis requires system stability, vibrations modes, and critical speeds. A theory to predict
the AMB damping coefficients and the stiffness was proposed by Xu et al., (2017). Rotor unbalance characteristics were
considered for formulation of the theory. The theory used Timoshenko beam theory to generate the proposed finite element
rotor model. An identification procedure was developed through utilization of finite element model. The proposed model
exhibited higher efficiency rate than other conventional beam theory techniques.

Euler–Bernoulli Beam Theory

Bauchau et al., (2009) proposed Euler-Bernoulli beam theory for constructing aeronautical composite materials.
Zhu & Chung, (2015) presented a new nonlinear coupling effect of the axial and lateral displacements to deploy beam with
spin. The new nonlinear model was proposed through assimilation of the Euler-Bernoulli beam theory and the von Karman
theory. The study analysed the characteristics of linear and nonlinear models. The implications of parameters of both types
of models were also examined. The study found remarkable differences between the working procedure and behaviour of
linear and nonlinear models. Fluctuation and alteration in the beat phenomenon due to intrusion of two similar natured
frequencies of the spinning beam was observed at the end of the study.

A new theory on the bending of Bernoulli-Euler beam was suggested by Park &Gao, (2006).
The study concentrated on enhanced couple stress theory to formulate the revamped model. For this, a differential
formulation using minimum total potential energy was applied using internal material length. Euler–Bernoulli beam theory
was studied and applied by Alshorbagy et al. (2011) to analyse the transversally functionally graded beams. Free vibration
response of the selected beams were examined with the help of finite element. In different studies, Shahba et al., (2011a)
&Shahba et al., (2011b) analysed axially functionally graded (AFG) beams. The studies focused on stability and vibration
of AFG beams. Euler–Bernoulli and Timoshenko beams were taken as reference beams for these studies. A finite element
method and various numerical methods were employed in these researches. . Vibration analysis for non-uniform and non-
homogenous micro-beams was carried out by Akgöz&Civalek, (2013). The study assessed and incorporated the threshold
of micro-beam. The material characteristics and the cross-sectional properties of the selected micro-beam were dissimilar
in nature. It was found that, there are significant impacts of taper ratios and material properties on natural frequencies in
case of AFG tapered micro beams. Strain gradient theory was taken as reference by Kahrobaiyan et al., (2011) to analyse a

www.tjprc.org SCOPUS Indexed Journal [email protected]

16 Shivanand & Dr. Shravankumar B. Kerur

size-dependent functionally graded (FG) Euler–Bernoulli beam theory.

A new model was suggested by Chung, (2016) to install spinning beam. The study also analysed the properties
and activities of the spinning beam. The model came into effect through the implementation of Rayleigh and Bernoulli
beam theories. Inertial references and rotary inertia effects of spinning beam were examined under this study.
The study also evaluated the beat phenomena related to spinning Rayleigh beam by positioning it in an inertial reference
frame. The results provide more precise and reliable outcomes for dynamic behaviors when the spinning beam is utilized.
Oke&Khulief, (2016) conducted a study on the finite element. The study employed B-spline wavelets on the interval for
research conduction. The objective of the study was to realize free vibration properties of composite pipes. Wavelet space
was initially used to design finite element for the study. Then that element was converted into physical space.
Wavelet functions and B-spline scaling were applied to obtain the quotient of stiffness and mass of composite element.
In this, the design is considered Euler-Bernoulli beam theories which utilize significantly fewer elements compared to
conventional techniques. Phadatare et al., (2017) presented the evaluation of nonlinear operations with the aim of the
divergences and chaotic performance of an elastically made flexible rotor-bearing system. The study contemplated ground
motion with harmonic characteristics. Also, the higher-order Euler– Bernoulli deformation theory was implemented that
controls the nonlinear dynamic characteristics of the rotating system.

Shear Deformation Beam Theory (SDBT)

A model analysing the static and dynamic characteristics of narrow edged composite beams was suggested by
Suresh and Nagaraj, (1996). Open and close sectioned HSDT was employed for development of the model. The results are
confirmed by using analytical comparison and the static deflections of composite beams. Another model for representation
of displacement structures was proposed by Marur and Kant, (1996). Free vibration of composite beams was analysed in
the study for representation of three higher order frameworks. It was found that models using higher order theories
obtained lower frequencies with respect to other existing theories. Buckling and free vibration attributes of stepped
composite beams with laminations was examined by Song and Waas, (1997) and Matsunaga, (2001). Both the studies
applied HSDT. The obtained outcomes of both the studies were analysed with respect to first-order deformation beam
theory. The comparison did not reveal any significant advantage of broad range of beam geometry. Two FEM and two
higher order techniques were suggested by Subramanian, (2006) for laminated beams. Symmetrically laminated beams and
dissimilar thickness ratios were considered in that study

Chang et al., (2004) proposed a general spinning composite shaft model which was comprised of discrete
isotropic rigid disks bearings. Shear deformable beam theory of first order was employed to figure out the strain energy
level of the shaft. Three-dimensional constitutive relations of material was also considered for this purpose. Rotating
coordinate systems of the shaft was used in this study to obtain the kinetic energy. The energy was obtained through
consideration of shaft cross-sectional area. To formulate the required equations for this study, Hamilton’s extended
theorem was used. The resulting model incorporated with gyroscopic effects, transverse shear deformation rotary inertia,
and coupling effects. The results show that the proposed beam theory provides better transient responses of a particular
composite shaft. Trigonometric deformation theory was employed by Jun et al., (2014) to examine laminated shallow
curved beams for the analysis of vibration patterns. . In the study, Wittrick-Williams algorithm was used to assess the
mode shapes and natural frequencies of the laminated beams with shallow curves. Dynamic stiffness characteristic was
utilized for that assessment. . Higher-order shear deformation plate theories were suggested by Yahia et al., (2015) using

Impact Factor (JCC): 7.6197 SCOPUS Indexed Journal NAAS Rating: 3.11
A Review on Various Beam Theory Techniques for Dynamic 17
Analysis of Rotating Laminated Shafts

functionally graded plates to assess the wave propagation pattern. Lesser number of undefined variables and equations
were used in the proposed plate theory as compared to existing conventional first-order shear deformation theories. By
solving the eigenvalue problem, the critical dispersion relation of the functionally graded plate was obtained.

Vibration behaviour of functionally graded materials was the foundation for the higher order beam theories of
Thai &Vo, (2012) and Sahmani, & Ansari, (2013). . Filippi& Carrera, (2015) proposed a Carrera Unified Formulation
(CUF) which was developed through integration of unsteady aerodynamic theories and higher order beam theories.
The model analysed aeroelasticproperties of rotating and fixed wings. Multi-sectional and rectangular contour of
composite and isotropic materials were analysed for this research model. Impacts of lamination structures, aerodynamic
theories, and the order of structural models on the flutter conditions of the beam were also analysed through this study. .
The simulation results of the study demonstrated that the CUF provides the excellent performance of the dynamics and
aeroelasticity of rotors in terms of accuracy, flutter instability. Shabanlou et al., (2017), Simsek& Reddy, (2013) and
Ebrahimi&Barati, (2016) investigated the vibration assessment of FG spinning beam which is applied to thermal
environment with the help of higher order SDBT. Also, a displacement field of hollow circular cylindrical spinning beam
was developed which maintained the shear stress to be free at both outer and inner surface of the beam.

Comparison of Different Beam Theory Techniques

The comparative analysis of different beam theory techniques for rotating laminated shafts is shown in Table I.
This comparison table provides critical speed (in rpm) of the each beam theory technique.

Table 1: Comparison of Beam Theory Techniques

Beam theory Critical Speed
S. No Paper/Author Name
Techniques used (in rpm)
Analysing the composite shaft rotor with the help of layer wise EMBT 5746
1.
theory. (Singh & Gupta, 1996) LBT 5620
The effect of coupling mechanisms and stacking sequence on the
2. Modified EMBT 5552
natural frequencies of composite shafts (Gubran& Gupta, 2005)
Analysis of the dynamics of rotating composite shafts (Sino et al.,
3. SHBT 5435
2008)
Analysis of the dynamics of rotating composite shafts with the
4. LBT 5769
help of layerwise theory (Arab et a., 2017b)
Identifying parameters of active magnetic bearings from the rotor
5. TMBT 6000
unbalance responses. (Xu et al., 2017)
Assessment of nonlinear responses and bifurcating the rotor
Euler-Bernoulli
6. bearing system which is mounted on a platform that moves. 2865
beam theory
(Phadatare et al., 2017)

CONCLUSIONS

This paper discussed the mechanism of rotating laminating shafts using various beam theory techniques. The
beam theory techniques used in this paper include, EMBT, SHBT, Modified EMBT, LBT, TMBT, Euler-Bernoulli beam
theory and SDBT. All techniques have its own pros and cons in terms of critical speed, accuracy, natural frequencies and
stiffness. In this, modified EMBT offers more efficient performance of tubular composite shafts for dynamic rotor analysis
than the EMBT. From this review, the beam theory techniques such as LBT, TMBT and SDBT techniques provide more
accurate performance with higher stiffness. In Future, the beam theory techniques can be improved to enhance the dynamic
performance of rotating laminated shafts.

www.tjprc.org SCOPUS Indexed Journal [email protected]

18 Shivanand & Dr. Shravankumar B. Kerur

REFERENCES

1. Akgoz, B, &Civalek, O. (2013) Free vibration analysis of axially functionally graded tapered Bernoulli–Euler microbeams
based on the modified couple stress theory. Composite Structures, 98, 314-322.

2. Alshorbagy, A. E., Eltaher, M. A., & Mahmoud, F. F. (2011) Free vibration characteristics of a functionally graded beam by
finite element method. Applied Mathematical Modelling, 35(1), 412-425.

3. Alwan, V., Gupta, A., Sekhar, A. S., &Velmurugan, R. (2010) Dynamic analysis of shafts of composite materials. Journal of
Reinforced Plastics and Composites, 29(22), 3364-3379.

4. Arab, S. B., Rodrigues, J. D., Bouaziz, S., & Haddar, M. (2017b) Dynamic analysis of laminated rotors using a layerwise
theory. Composite Structures.

5. Arab, S. B., Rodrigues, J. D., Bouaziz, S., & Haddar, M. (2018) Stability analysis of internally damped rotating composite
shafts using a finite element formulation. ComptesRendusMécanique.

6. Banerjee, J. R., & Su, H. (2006) Dynamic stiffness formulation and free vibration analysis of a spinning composite beam.
Computers & structures, 84(19-20), 1208-1214.

7. Bauchau, O. A., & Craig, J. I. (2009) Euler-Bernoulli beam theory. In Structural analysis (pp. 173-221). Springer, Dordrecht.

8. Bazaria, B., & Kumar, P. (2018). Optimization of spray drying parameters for beetroot juice powder using response surface
methodology (RSM). Journal of the Saudi society of agricultural sciences, 17(4), 408-415.

9. Bert, C. W., & Kim, C. D. (1995) Whirling of composite-material driveshafts including bending-twisting coupling and
transverse shear deformation. Journal of Vibration and Acoustics, 117(1), 17-21.

10. David, D. C. N., Stephen, S. E. A., & Ajoy, J. A. (2016). Cost minimization of welded beam design problem using PSO, SA, PS,
GOLDLIKE, CUCKOO, FF, FP, ALO, GSA and MVO. Int. J. Appl. Math, 5, 1-14.

11. Chang, C. Y., Chang, M. Y., & Huang, J. H. (2004) Vibration analysis of rotating composite shafts containing randomly
oriented reinforcements. Composite structures, 63(1), 21-32.

12. Chang, M. Y., Chen, J. K., & Chang, C. Y. (2004) A simple spinning laminated composite shaft model. International journal of
solids and structures, 41(3-4), 637-662.

13. Chatelet, E., Lornage, D., &Jacquet-Richardet, G. (2000) Dynamic behavior of thin-walled composite shafts: a three
dimensional approach. In ESDA Montreux (pp. 1-5).

14. Chen, L. W., &Peng, W. K. (1998) The stability behavior of rotating composite shafts under axial compressive loads.
Composite Structures, 41(3-4), 253-263.

15. Cho, M., & Kim, J. S. (2001) Higher-order zig-zag theory for laminated composites with multiple delaminations. Journal of
Applied Mechanics, 68(6), 869-877.

16. Davies, J. M. (1998) Generalised beam theory (GBT) for coupled instability problems. In Coupled Instabilities in Metal
Structures (pp. 151-223). Springer, Vienna.

17. Dos Reis, H. L. M., Goldman, R. B., &Verstrate, P. H. (1987) Thin-walled laminated composite cylindrical tubes: part III—
bending analysis. Journal of Composites, Technology and Research, 9(2), 58-62.

18. Ebrahimi, F., & Barati, M. R. (2016) A nonlocal higher-order shear deformation beam theory for vibration analysis of size-
dependent functionally graded nanobeams. Arabian Journal for Science and Engineering, 41(5), 1679-1690.

Impact Factor (JCC): 7.6197 SCOPUS Indexed Journal NAAS Rating: 3.11
A Review on Various Beam Theory Techniques for Dynamic 19
Analysis of Rotating Laminated Shafts

19. Elishakoff, I., &Pentaras, D. (2009) Natural frequencies of carbon nanotubes based on simplified Bresse-Timoshenko theory.
Journal of Computational and Theoretical Nanoscience, 6(7), 1527-1531.

20. Filippi, M., & Carrera, E. (2016) Bending and vibrations analyses of laminated beams by using a zig-zag-layer-wise theory.
Composites Part B: Engineering, 98, 269-280.

21. Gayen, D. (2013) Finite element based vibration and stability analysis of functionally graded rotating shaft system under
thermal environment (Doctoral dissertation).

22. Ghoneam, S. M., Hamada, A. A., & El-Elamy, M. I. (2011) Dynamic analysis of a rotating composite shaft. ZeszytyNaukowe.
Mechanika/PolitechnikaOpolska, (99), 20-20.

23. Gubran, H. B. H. (2000) Dynamic stress analysis and optimization studies on fibre-reinforced composite shafts (Doctoral
dissertation, PhD Thesis, IIT, Delhi).

24. Gupta, K. (2015) Composite Shaft Rotor Dynamics: An Overview. In Vibration Engineering and Technology of Machinery (pp.
79-94). Springer, Cham.

25. Hajianmaleki, M., &Qatu, M. S. (2012) A rigorous beam model for static and vibration analysis of generally laminated
composite thick beams and shafts. International Journal of Vehicle Noise and Vibration, 8(2), 166-184.

26. Hajianmaleki, M., &Qatu, M. S. (2012) Static and vibration analyses of thick, generally laminated deep curved beams with
different boundary conditions. Composites Part B: Engineering, 43(4), 1767-1775.

27. Hosseini, S. A. A., &Khadem, S. E. (2009) Free vibrations analysis of a rotating shaft with nonlinearities in curvature and
inertia. Mechanism and Machine theory, 44(1), 272-288.

28. Jacquet-Richardet, G., Chatelet, E., &Nouri-Baranger, T. (2011) Rotating internal damping in the case of composite shafts. In
IUTAM Symposium on Emerging Trends in Rotor Dynamics (pp. 125-134). Springer, Dordrecht.

29. Jin, G., Yang, C., & Liu, Z. (2016) Vibration and damping analysis of sandwich viscoelastic-core beam using Reddy’s higher-
order theory. Composite Structures, 140, 390-409.

30. Jun, L., Guangwei, R., Jin, P., Xiaobin, L., &Weiguo, W. (2014) Free vibration analysis of a laminated shallow curved beam
based on trigonometric shear deformation theory. Mechanics Based Design of Structures and Machines, 42(1), 111-129.

31. Kahrobaiyan, M. H., Rahaeifard, M., Tajalli, S. A., &Ahmadian, M. T. (2012) A strain gradient functionally graded Euler–
Bernoulli beam formulation. International Journal of Engineering Science, 52, 65-76.

32. Kasawar, G. B., & Farooqui, M. (2010). Development and validation of a stability indicating RP-HPLC method for the
simultaneous determination of related substances of albuterol sulfate and ipratropium bromide in nasal solution. Journal of
pharmaceutical and biomedical analysis, 52(1), 19-29.

33. Kant, T., & Gupta, A. (1988) A finite element model for a higher-order shear-deformable beam theory. Journal of sound and
vibration, 125(2), 193-202.

34. Kim, C. D., & Bert, C. W. (1993) Critical speed analysis of laminated composite, hollow drive shafts. Composites engineering,
3(7-8), 633-643.

35. Lee, J. (2000) Free vibration analysis of delaminated composite beams. Computers & Structures, 74(2), 121-129.

36. Li, X. F. (2008) A unified approach for analyzing static and dynamic behaviors of functionally graded Timoshenko and Euler–
Bernoulli beams. Journal of Sound and vibration, 318(4-5), 1210-1229.

www.tjprc.org SCOPUS Indexed Journal [email protected]

20 Shivanand & Dr. Shravankumar B. Kerur

37. Lien-Wen, C., & Der-Ming, K. (1991) Finite element analysis of natural whirl speeds of rotating shafts. Computers &
Structures, 40(3), 741-747.

38. Marur, S. R., & Kant, T. (1996) Free vibration analysis of fiber reinforced composite beams using higher order theories and
finite element modelling. Journal of sound and vibration, 194(3), 337-351.

39. Matsunaga, H. (2001) Vibration and buckling of multilayered composite beams according to higher order deformation
theories. Journal of Sound and Vibration, 246(1), 47-62.

40. Montagnier, O., & Hochard, C. (2013) Optimisation of hybrid high-modulus/high-strength carbon fibre reinforced plastic
composite drive shafts. Materials & Design, 46, 88-100.

41. Nelson, H. D. (1980) A finite rotating shaft element using Timoshenko beam theory. Journal of mechanical design, 102(4),
793-803.

42. Nezhad, H. S. A., Hosseini, S. A. A., &Zamanian, M. (2017) Flexural–flexural–extensional–torsional vibration analysis of
composite spinning shafts with geometrical nonlinearity. Nonlinear Dynamics, 89(1), 651-690.

43. Oke, W. A., &Khulief, Y. A. (2016) Vibration analysis of composite pipes using the finite element method with B-spline
wavelets. Journal of Mechanical Science and Technology, 30(2), 623-635.

44. Park, S. K., &Gao, X. L. (2006) Bernoulli–Euler beam model based on a modified couple stress theory. Journal of
Micromechanics and Microengineering, 16(11), 2355.

45. Phadatare, H., Choudhary, B., &Pratiher, B. (2017) Evaluation of nonlinear responses and bifurcation of a rotor-bearing
system mounted on moving platform. Nonlinear Dynamics, 90(1), 493-511.

46. Qatu, M. S., & Iqbal, J. (2010) Transverse vibration of a two-segment cross-ply composite shafts with a lumped mass.
Composite Structures, 92(5), 1126-1131.

47. Reddy, a. C. Low and high temperature micromechanical behavior of bn/3003 aluminum alloy nanocomposites.

48. Rajasekaran, S. (2013) Free vibration of centrifugally stiffened axially functionally graded tapered Timoshenko beams using
differential transformation and quadrature methods. Applied Mathematical Modelling, 37(6), 4440-4463.

49. Rao, D. K., & Roy, T. (2016) Vibration Analysis of Functionally Graded Rotating Shaft System. Procedia Engineering, 144,
775-780.

50. Reddy, J. N. (1997) On locking-free shear deformable beam finite elements. Computer methods in applied mechanics and
engineering, 149(1-4), 113-132.

51. Sahmani, S., & Ansari, R. (2013) On the free vibration response of functionally graded higher-order shear deformable
microplates based on the strain gradient elasticity theory. Composite Structures, 95, 430-442.

52. Sekhar, A. S., &Srinivas, B. N. (2002) Vibration characteristics of slotted shafts. Journal of sound and vibration, 251(4), 621-
630.

53. Shabanlou, G., Hosseini, S. A. A., &Zamanian, M. (2017) Vibrations Analysis of FG spinning beam using higher order shear
deformation beam theory in thermal environment. Applied Mathematical Modelling.

54. Shahba, A., Attarnejad, R., &Hajilar, S. (2011a) Free vibration and stability of axially functionally graded tapered Euler-
Bernoulli beams. Shock and Vibration, 18(5), 683-696.

Impact Factor (JCC): 7.6197 SCOPUS Indexed Journal NAAS Rating: 3.11
A Review on Various Beam Theory Techniques for Dynamic 21
Analysis of Rotating Laminated Shafts

55. Shahrjerdi, A., &Yavari, S. (2018) Free vibration analysis of functionally graded graphene-reinforced nanocomposite beams
with temperature-dependent properties. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 40(1), 25.

56. Shufrin, I., &Eisenberger, M. (2005) Stability and vibration of shear deformable plates––first order and higher order
analyses. International journal of solids and structures, 42(3-4), 1225-1251.

57. Silvestre, N. (2007) Generalised beam theory to analyse the buckling behaviour of circular cylindrical shells and tubes. Thin-
Walled Structures, 45(2), 185-198.

58. Simsek, M. (2010) Fundamental frequency analysis of functionally graded beams by using different higher-order beam
theories. Nuclear Engineering and Design, 240(4), 697-705.

59. Singh, S. P., & Gupta, K. (1996) Composite shaft rotordynamic analysis using a layerwise theory. Journal of Sound and
Vibration, 191(5), 739-756.

60. Sino, R., Chatelet, E., Nouri-Baranger, T., & Jacquet-Richardet, G. (2006) Stability of internally damped rotating composite
shafts considering transversal shear. In The Eleventh International Symposium on Transport Phenomena and Dynamics of
Rotating Machinery, ISROMAC'11 (No. CD-Rom, pp. 7-p).

61. Song, S. J., &Waas, A. M. (1997) Effects of shear deformation on buckling and free vibration of laminated composite beams.
Composite Structures, 37(1), 33-43.

62. Subramanian, P. (2006) Dynamic analysis of laminated composite beams using higher order theories and finite elements.
Composite Structures, 73(3), 342-353.

63. Suna, B. (2014) Design and Analysis of Laminated Composite Materials (Doctoral dissertation).

64. Suresh, J. K., &Nagaraj, V. T. (1996) Higher-order shear deformation theory for thin-walled composite beams. Journal of
aircraft, 33(5), 978-986.

65. Tessler, A., Di Sciuva, M., &Gherlone, M. (2009) A refined zigzag beam theory for composite and sandwich beams. Journal of
composite materials, 43(9), 1051-1081.

66. Thai, H. T., &Vo, T. P. (2012) Bending and free vibration of functionally graded beams using various higher-order shear
deformation beam theories. International Journal of Mechanical Sciences, 62(1), 57-66.

67. Wang, C. M., Zhang, Y. Y., Ramesh, S. S., &Kitipornchai, S. (2006) Buckling analysis of micro-and nano-rods/tubes based on
nonlocal Timoshenko beam theory. Journal of Physics D: Applied Physics, 39(17), 3904.

68. Xu, Y., Zhou, J., Di, L., & Zhao, C. (2017) Active magnetic bearings dynamic parameters identification from experimental
rotor unbalance response. Mechanical Systems and Signal Processing, 83, 228-240.

69. Yahia, S. A., Atmane, H. A., Houari, M. S. A., &Tounsi, A. (2015) Wave propagation in functionally graded plates with
porosities using various higher-order shear deformation plate theories. Structural Engineering and Mechanics, 53(6), 1143-
1165.

70. Yongsheng, R., Qiyi, D., &Xingqi, Z. (2013) Modeling and dynamic analysis of rotating composite shaft. Journal of
Vibroengineering, 15(4).

71. Yongsheng, R., Xingqi, Z., Yanghang, L., &Xiulong, C. (2014) Vibration and instability of rotating composite thin-walled
shafts with internal damping. Shock and Vibration, 2014.

72. Zhu, K., & Chung, J. (2015) Nonlinear lateral vibrations of a deploying Euler–Bernoulli beam with a spinning motion.
International Journal of Mechanical Sciences, 90, 200-212.

www.tjprc.org SCOPUS Indexed Journal [email protected]

22 Shivanand & Dr. Shravankumar B. Kerur

73. Zhu, P., Lei, Z. X., &Liew, K. M. (2012) Static and free vibration analyses of carbon nanotube-reinforced composite plates
using finite element method with first order shear deformation plate theory. Composite Structures, 94(4), 1450-1460.

74. Zinberg, H., & Symonds, M. F. (1970) The development of an advanced composite tail rotor driveshaft. In 26th Annual
National Forum of the American Helicopter Society, Washington, DC, June (pp. 16-18).

75. Zorzi, E. S., & GIORDANO, J. (1985) Composite shaft rotordynamic evaluation. In ASME, Design Engineering Technical
Conference, Cincinnati, OH (p. 1985).

Impact Factor (JCC): 7.6197 SCOPUS Indexed Journal NAAS Rating: 3.11