BSC COMMAND

ZEEI;
ZEEI:BCF=bcf no;

ZEEP;
ZEOL:bcf no;
ZEOL::NR=7706;
ZEOL::NR=7767;
ZEOL::NR=7704;
ZEOL::NR=7705;
ZEOL::NR=7406;
ZEOH::BCF=bcf num;
ZQSI;
ZNEL;
ZEFS:bcf no:L/U;
ZEQS:BTS=bts no:L/U;
ZERS:BTS=bts no:TRX= Trx no:L/U;
ZEFR:bcf num:OMU/SITE;
ZERM:BTS=bts num,TRX=trx num:GTRX=Y/N;
ZAHO:ET,et num;
ZUSC:ET:et num:BL/WO;
ZDTF:TCSM,et num;
ZEEL;
ZAHO;
ZYEF:ET,etnum;
ZUSI;
ZUSI:ET,et num;
ZUSI:COMP;
ZZZZ;
ZQNI;
ZQRI;
ZEFE;
ZERO:BCF=bcf num;
ZESI:ID=edap id;
ZESI:ID=edap id:TRXS;
ZDSB:::PCM=et num;
ZDTI:::PCM=et num;
ZUSI:MCMU;
ZYMO:ET,et num;
ZDSB:::PCM=et num;
ZWUP:etnum;
ZAHP:::yyyy-mm-dd;
ZQWL:BCF=bcf num;
ZEFP;
ZEFO:Bbcf num;
ZEFO:bcf num:IOP;
ZEFX:bcfnum:INBR=alarm number:POL=OPEN/CLOSE;
ZDTC:D-channel name:BL/WO;
ZERC:Trx creation
ZERD:Trx Deletion
ZDSE:
ZEOH:yy-mm-dd:hh-mm-ss:BCF=bcf num;
ZEEL:BL;
ZWAT;
ZAHO::NR=4000-4007;
ZDTC:lapdname:BL/WO
ZEWV:bcf num:BU;
ZEUO:BTS=bts num;
ZEUG:BTS=btsnum:PMAX=(1…43);
ZEQV=BTS=btsnum:GENA=Y/N;
ZEDQ:BTS=btsnum:GPRS;
ZDRI;
ZUSI:TCSM;
ZNET;
ZEEL;
ZEFM:bcf num:BBU=NONE;
ZEFM:bcf num:BBU=NONE;
ZAHP:ET,ET NO;
ZYMO:ET,ET NO;
ZEWO:BCF NO.;
ZEWV:52:BU;
ZEFO:8:ALL;
ZEFE:TID=6:TEXT=”BATTERY DISCHARGE”;
ZEFX;
ZEFX:BCF NO:INBR=ALARM NO.:ROU=NOT,POL=OPEN:SEV=A
ZEEL:BL;

ZEOR: BCF NO.: ALARM NO.;

Description
to see status of all sites in bsc
Used to check status of perticuler bcf

To see all the sites and its bcf numbers

To check current alarm on particular BCF
To check doen sites in bsc (OMU down)
To check down sector abd site (BCCH missing)
To see all sites having PCM failure/blocked
To see all sites having LAPD failure/blocked
To see all sites having Low Battery alarm
To check history alarm on bts
To check status of X.25 link
To chck status of all signallings(TCSM)
To lock and unlock BCF
To lock and unlock sector ( sector reset)
To lock and unlock Trx (TRX reset)
To site /omu reset in SAFE MODE
To give Trx reset if trx blocked by system
To check alarm on ET
To Making ET working or block(ET reset)
TO check state of ET
To check no. of calls running in bsc
To see all bsc related alarms
To check PCM status on ET/ET loop check
To see all ET status
Chech ET status
Status of all computer unites in a BSC
terminate session
To know Nuemerical ID of BSC
To find out IP of bsc (OMU) IP allocated to BSC
To modification of External Alarm TEXT
To check traffic of TRX (TCH)
To check Edap time slot(To know Edap ID run ZERO first)
To check DAP trx
To check TRx Signalling on ET(Time slot value&Bit rate)
To find out D channel Details on ET
MCMU unit status (same ZUSI:BCSU; for BCSU status)
To check slips on ET
To know wheather a ET is in use or not
To know a ET Type (TCSM/Abis)(Signalling or ABIS
To know alarm history of bsc
To know the Q1 address of FIUs present in a site
To check External alarm ID
To know ISD feature implemented on site or not
To know alarm congiguration in BTS
To change polarity of an external alarm
To change the status of D-channel

trx should be locked before deletion

Lap-D creation
Alarm related to particular date and time
To see locked sites,sector & Trx in BSC in Whole BSC
To check bsc alarm text ID
To check bsc alarm
To give lapd reset
To give Software Backup
To check bts power
To change BTS power
To enable /Disable GPRS
To checkGPRS Enable or not for bts
To check clock status(Two clocks internal & external)
To check ATER link status
To check BSC SS7 links status
To check BSC traffic
for battery backup timer

ET ALARM HISTORY
Fault dignos on ET
Flexi BTS Software check through BSC
BCF reset through sw reset
To see alarm Text of BCF 8
10.External alarm text change :-(Whole bsc sites)
EXTERNAL ALARM TEXT INTERCHANGE
52.Extenal alarm Polarity change command.
15.Block trx list check in BSC :-

42. ALARM REMOVE FROM BSC

BSC MMI COMMANDS
ET SENH TO WO STATE ZUSI:ET,394;
ZUSI:ET,et num; ET status 1. ZWUP:394; if it result AIPRB (in second line) than we can wor

2.ZDTI:::PCM=394; /*** DX
ERROR: 10463 ***/
/*** D-CHANNEL DOES NOT EXIST
***/ this error show that ET is
ZAHO:ET,et num; Alarm on ET already not in use
ZYEF:ET,etnum; PCM status 3.ZUSC:ET,394:SE,FCD; Y SE-OU
ZUSC:ET:et num:BL/WO; ET Reset 4.ZUSC:ET,394:TE,FCD; Y TE-EX
ZAHP:ET,etnum; Alarm history on that ET 5.ZUSC:ET,394:WO,FCD; Y WO-EX

crtl+B repeats last and previous command on MML

crtl+Y interrupt current command being types or run

WO-EX --- SP-EX working spare ZUSU:BCSU,bcsu num:SP;

SP-EX --- TE-EX sapre test ZUSU:BCSU,bcsu num:TE;
TE-EX ---- SE-OU internal start seprate out ZUSU:BCSU,bcsu num:SE;
SE-OU ---- SE-NH seprate node hardware
Only after putting any unit SE-NH that can be jack out

SE-NH -----SE-OU Unit status ZUSI:COMP;

SE-OU ------TE-EX after test run diagnos to run diagnos
Diagnos start ZUDU:MCMU,1;
No active Diagnos Diagnos check
Check Diagnos Result ZUDQ;
Its must be UNIT OK then put into SP-EX No active Diagnosis Test
SP-EX -------Wo-EX Diagnos Result
ZUDH:MCMU,1;
UNIT OK reslut it must be ok

10.84.200.86 OMU(BSC)
10.84.200.85 MCMU1
10.84.200.84 MCMU0
10.84.200.83 Lapto IP if login through MCMU portETH2 of first card)

Transcoder check
ZRCI:SEA=4:ETPCM=etnum;
changing ET in to AIPRB (abis ET)
WUC:ET,405:ET4E,0:IF=ABIS:BCSU,4:;

ZWQO:CR; \\CHECK BACKUP FILE and fallback name

ZIWX::WS,NODEF::%,%,; \\CHECK ZIP FILE.
IF zip not present than use below command .
wait till auto sign out and check after one hour
ZIXF:OMU,WDU-S,/FB201019,:OMU,WDU-S,/,FB201019:TIME=7200;
n second line) than we can work on it
For Any card change in bsc or BSC card change state For Example BCSU card

ZUSC:BCSU,0; For any particular BSC card status

Extraction or Lock of card /Enable or Disable of card

From working to Disable

ZUSC:BCSU,1:WO; working
ZUSC:BCSU,1:SP; Spare
ZUSC:BCSU,1:TE; Test
ZUSC:BCSU,1:SE; Seprate,out of service
ZUSC:BCSU,1:SE; No hardware

From Disable to working

ZUSC:BCSU,1:SE; No hardware
ZUSC:BCSU,1:SE; Seprate,out of service
ZUSC:BCSU,1:TE; Test
ZUSI:COMP; after unit in test we rununit diagnos
ZUDU:BCSU,1; diagnos run command
ZUDH:BCSU,1; Result of Diagnos of unit
ZUDQ; For status check either diagnos run or not
in case run there would be unit ok
ZUSC:BCSU,1:SP; spare
ZUSC:BCSU,1:WO; working
JANTASEWA IP
NETWORK CONNECTION WINDOW
\\10.55.87.150

Username :janta
Pass :Nokia@123
Pass Nokia^123456
For 3G DUW Adress 169.254.1.1 connect
169.254.1.2
255.255.0.0
169.254.1.1

Baseband 5216 unit Host 169.254.2.1

169.254.2.1 username -rbs
255.255.0.0 password -rbs
169.254.2.2 internet explorer https://169.254.2.2/ea.html
For TCU backup IP username : admin
192.168.1.2 pass: hidden
255.255.25.0
192.168.1.1

FPH IP port OOB internet explore //192.168.254.100

192.168.254.101 pass; sysmanager
255.255.255.0

anil
Nokia@123
administrator
Nokia@123456
Ctl
Jaipur@12345

Router port Details

LED
I/O
LED

LED
O/O 1/1/0 .....................................1/1/4.......................................1/1/9

1/0/0..................................1/0/4..........................................1/0/9
LED

0/1/0......................................0/1/4......................................0/1/9

0/0/0................................0/0/4............................................0/0/9
 Chnnodeb Chenai@12
Rajnodeb Rajbts@12
Column2 Column1
X=trx num:L/U;
E COMMAND > ZIAG;
NEW PASS VERIFICATION NEW PASS
Gujnodeb Gujart@12
Harnodeb Haryna@12
Mahnodeb Mandg@12
Robnodeb Bengal@12
Rotnodeb Rtamil@12
Upenodeb Upebts@12
Laptop IP Trx Commands
10.55.87.162 To find out TCH time slot ZDTI:::PCM=et num;
255.255.255.128 To know trx signalling ZDSB:::PCM=et num;
10.55.87.130 Trx reset ZERS:BTS=bts num,TRX=trx num:L/U;
10.84.193.39
10.84.193.40
Internet Explorer
https://10.84.190.78/citrix/storeweb/ enter BTNK01 206765
BTNK02 371675
login BDVL01 951478
username : rc102616nms\rj4998 (NC8331 PASS de17!c27 ) BKOT04 900701
password :Nokia@12345 FOR BBLW03 BBLW03 374179
BJPR16 390505
Apps
for bsc login R2win
refection window will appear
connection ->connection setup-> secureshell BSC PASSWORD CHANGE COMMAND > ZIAG
OLD PASS NEW PASS VERIFIC
Host Name : 10.84.190.9
Pass : oss
pass :nsn
rajtrl1> SSH -L NC4998 BTNK01 enter
Pass AB12!T82
Nokia 3G login
IExplorer
https://10.84.191.55/OMSElementManager/
ZTE IDU LOGIN :--------
Laptop IP: 192.168.1.15
Internet Explorer https://192.168.1.16
UserID :admin
Pass :admin
Username :Nemuadmin
pass :nemuuser
select RNC and wbts ID now find IP
for WBTS login
User Name :Rajnodeb Chnnodeb
Pass :Rajbts@12 Chenai@12
Gujarat Gujnodeb
Laptop IP
10.55.87.162
255.255.255.128
10.55.87.130
10.84.193.39
10.84.193.40
Internet Explorer
https://10.84.190.78/ci
login
username : rc102616n
password :Nokia@123
Apps
for bsc login R2win
refection window will
connection ->connecti
Host Name : 10.84.190
Pass : oss
pass :nsn
rajtrl1> SSH -L NC4998
Pass AB12!T82
Nokia 3G login
IExplorer
https://10.84.191.55/O
ZTE IDU LOGIN :--------
Laptop IP: 192.168.1.1
Internet Explorer
UserID :admin
Pass :admin
Username :Nemuadmi
pass :nemuuser
select RNC and wbts I
for WBTS login
User Name :Rajnodeb
Pass :Rajbts@1
Gujarat Gujnodeb
TRX LOCK
TRX DELETE
LAPD LOCK
LAPD DELETE
LAPD CREATION
TRX CREATION
FOR TRX SIGNALLING ON TCH
LAPD UNLOCK
TRX UNLOCK
TRX CREATION
ZERO:BCF=38;

NOTE : FREQ, LAPD NAME, TSC, SIGN,BCSU,BTS ID,BCF ID ,OLD ET,NEW ET, OLD TRAFFIC ,NEW TRAFFIC
ZERS:BTS=64,TRX=3:L;
ZERD:BTS=64,TRX=3;
ZDTC:T2203:AD;
ZDSD:T2203;
ZDSE:T2203,:BCSU,4:0,3:32,412-25,0;
ZERC:BTS=64,TRX=3:GTRX=N,:FREQ=32,TSC=2,PCMTSL=412-1:DNAME=T2203:SIGN=0,CH0=TCHD,CH1=TCHD,CH2=TCHD,CH3=T
ZERC:BTS=114,TRX=12:GTRX=N,:FREQ=44,TSC=6,PCMTSL=356-1:DNAME=T3812:SIGN=1,CH0=SDCCH,CH1=TCHD,CH2=TCHD,CH
ZDTC:T2203:WO;
ZERS:BTS=64,TRX=3:U; OR ZERS:BTS=64,TRX=8,:U;

ZERS:BTS=243,TRX=12:L;
ZERD:BTS=243,TRX=12;
ZDTC:T8112:AD;
ZDSD:T8112;

ZDSE:T8112,:BCSU,1:0,12:16,1561-17,0;
ZERC:BTS=241,TRX=12:GTRX=N,:FREQ=48,TSC=6,PCMTSL=1561-17:DNAME=T8112:SIGN=1,CH0=SDCCH,CH1=TCHD,CH2=TCHD
ZDTC:T0508:WO;
ZERS:BTS=15,TRX=8:U;
. MAL fre addition
2.ZEEP; // To see all the site & its BCF IDs.
PRIMARY RATE ACCESS D-CH
3.ZEEL:BL; // To see the Blocked TRX in whole BSC < ZERS:BTS=15,TRX=8:U;

LOADING PROGRAM VERSIO

5.ZEOH::BCF=BCF NO; // To check history of alarm.

6.ZEOR:BCF NO:ALARM NO(10001-65534); // To cancel an alarm.

7.ZEFS:BCF NO:L/U; // To give site reset. BSC3i BDVL01 2
8.ZEFR:BCF NO:SITE/OMU; // To give site reset in safe mode also OMU reset. EXECUTION STARTED
9.ZEQS:BTS=BTS NO:L/U; // To give sector reset. ADMINISTRATIVE STATE CHA
10.ZERS:BTS=BTS NO,TRX=TRX NO:L/U; // To give TRX reset. SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBK
11.ZERM:BTS=BTS NO,TRX=TRX NO:GTRX=Y/N; // To give reset if TRX is blocked by system. /*** DX ERROR: 11259 ***/
/*** TOO FEW ARFCNS IN M
12.ZERM:BTS=BTS NO,TRX=TRX NO:PREF=P/N; // To change preference for ACTIVE TRX.
COMMAND EXECUTION FAI
13.ZWAT; // To check BSC alarm TEXT ID.
TRANSCEIVER DATA HANDLI
14.ZAHO::NR=4000-4007; // To check BSC alarm. <
15.ZAHO:ET,ET NO; // To check ET alarm.

16.ZAHP; // To check ET & BSC history alarms.

BASE STATION CONTROLLER
17.ZYEF:ET,ET NO; // To check PCM service state. < ZEQO
18.ZDTI:::PCM=ET NO; // To check signalling link for a site. LOADING PROGRAM VERSIO
19.ZDSB:::PCM=ET NO; // To check TIE value & BIT rate. /* DATA UNITS:
20.ZUSC:ET,ET NO:BL/WO; // To give ET reset. BTS IDENTIFICATION, BTS N
SEG IDENTIFICATION, SEG
21.ZDTC:LAPD NAME:BL/WO; // To give LAPD reset.
EQO:BTS
22.ZYMO:ET,ET NO; // To check SLIPS.

23.ZUSI:ET,ET NO; // To check ET status. /* IDENTIFY BASE TRANSCEI

24.ZWUP:ET NO; // To check the type of ET (ABIS or SIGNALLING). DECIMAL NUMBER 1 ... 6
25.ZERO:BCF=BCF NO; // To check traffic of the TRX.26.ZESI:ID=BCF NO; // To check EDAP. EQO:BTS=15
27.ZESI:ID=BCF NO:TRXS; // To check DAP TRX. /* GIVE PARAMETER GROUP
28.ZQUS:BCF=BCF NO,TRE=(RATIO);then 7;1;0; // To check receiving level. IDE ... BTS IDENTIFICATION
CEL ... CELL ACCESS PARAM
29.ZNEL; // To check signalling link status. RAD ... RADIO LINK CONTR
QUE ... QUEUEING PARAM
30.ZEFP; // To check External Alarm ID. CCH ... CCH CONFIGURATI
INT ... INTERFERENCE AVE
31.ZEFT:BCF NO:ON/OFF; // To switch ON/OFF the DG. MIS ... MISCELLANEOUS PA
HOP ... FREQUENCY HOPP
32.ZEFO:BCF NO:IOP; // To check POLARITY. BCC ... BCCH FREQUENCY
TRU ... TRUNK RESERVATIO
33.ZEFX:BCF NO:INBR=INPUT ID:POL=OPEN/CLOSED; // To change the POLARITY. GPRS .. GPRS PARAMETER
GPC ... GPRS CONTROL PA
34.ZEWV:BCF NO:BU; // To give SOFTWARE BACKUP. DAT ... DATA SERVICE PARA
AMR ... AMR PARAMETERS
35.ZEQE:BTS=BTS NO:AHOP=Y/N; // To remove ANTENNA HOP if PRESENT ALL ... ALL PARAMETERS
ZAHP:ET,#; displays alarm history for that ET
31.ZEFT:BCF NO:ON/OFF; // To switch ON/OFF the DG. MIS ... MISCELLANEOUS PA
HOP ... FREQUENCY HOPP
32.ZEFO:BCF NO:IOP; // To check POLARITY. BCC ... BCCH FREQUENCY
TRU ... TRUNK RESERVATIO
33.ZEFX:BCF NO:INBR=INPUT ID:POL=OPEN/CLOSED; // To change the POLARITY. GPRS .. GPRS PARAMETER
GPC ... GPRS CONTROL PA
34.ZEWV:BCF NO:BU; // To give SOFTWARE BACKUP. DAT ... DATA SERVICE PARA
AMR ... AMR PARAMETERS
35.ZEQE:BTS=BTS NO:AHOP=Y/N; // To remove ANTENNA HOP if PRESENT ALL ... ALL PARAMETERS
ZAHP:ET,#; displays alarm history for that ET DEFAULT IS IDE GROUP
ZEEL:BL; displays locked Sites, Sectors and TRXs on BSC
Investigating Clear Codes: EQO:BTS=15:
ZTUT:CLR; displays current clear codes on the MSC
ZTUL:CLR; displays latest history of clear codes /* GIVE PARAMETER GROUP
Canceling Bogus alarms on a Site: (Perform both commands)
ZEOR:#:alarm #; cancels alarm on site IDE ... BTS IDENTIFICATION
ZEFR:#:OMU; resets the OMU (Operations and Maintenance Unit) CEL ... CELL ACCESS PARAM
Canceling Bogus alarms on a BSC: RAD ... RADIO LINK CONTR
ZACC:####; cancels the alarm using the consecutive # in which it came in QUE ... QUEUEING PARAM
ZACA:####; cancels the alarm using the alarm identifier # CCH ... CCH CONFIGURATI
Locking and unlocking a Site: INT ... INTERFERENCE AVE
ZEFS:bcf #:L; locks entire Site without Forced Handover MIS ... MISCELLANEOUS PA
ZEFS:bcf #:U; unlocks entire Site HOP ... FREQUENCY HOPP
Locking and unlocking Sectors: BCC ... BCCH FREQUENCY
ZEQS:BTS=#:L; locks entire sector down without Forced Handover TRU ... TRUNK RESERVATIO
ZEQS:BTS=#:L:FHO,#; shuts down entire sector with Forced Handover GPRS .. GPRS PARAMETER
ZEQS:BTS=#:U; unlocks entire sector GPC ... GPRS CONTROL PA
Locking and unlocking TRXs: DAT ... DATA SERVICE PARA
ZERS:BTS=#,TRX=#:L; locks TRX down without Forced Handover AMR ... AMR PARAMETERS
ZERS:BTS=#,TRX=#:L:FHO,#; shuts down TRX with Forced Handover ALL ... ALL PARAMETERS
ZERS: BTS=#,TRX=#:U; unlocks TRX
Resetting the Site or OMU: DEFAULT IS IDE GROUP
ZEFR:#:SITE; restarts SITE
ZEFR:#:OMU; restarts OMU EQO:BTS=15:HOP;
Bouncing Lap D’s on a Site:
ZDTI:::PCM=#; displays Lap D channels for entire site BSC3i BDVL01 2
ZDTC:lap d #:BL; blocks desired Lap D channel
ZDTC:lap d #:WO; places Lap D channel in working state FREQUENCY HOPPING PARA
Error Checking on an ET (PCM): =======================
ZYMO:ET,#; checks error counter for specific ET
ZYEU:ET,#:SLIDL=5; resets error counter for specific ET SEG-0015 TNDBKL013
Querying the # of calls on a site: BCF-0005 BTS-0015 TNDB
ZERO:BTS=#; displays all calls on desired sector -------------------------------------
ZERO:BTS=#,TRX=#; displays all calls on desired TRX only BTS ADMINISTRATIVE STATE
Sparing or Rolling a BCSU: BTS OPERATIONAL STATE ....
ZUSI:BCSU; displays what BCSU the SP was previously on
ZFWO:BCSU=0&&8; displays what BCSU the BL condition is on BTS HOPPING MODE...........
ZUSC:BCSU,#:SP; spares the BCSU with the BL condition on it HOPPING SEQUENCE NUM
Y for Yes executes the command HOPPING SEQUENCE NUM
Statusing Timeslots: MAIO OFFSET....................
ZEEL::BCF=#; Status the timeslots on a BCF MAIO STEP......................(M
Status ET alarms on a BSC MOBILE ALLOCATION FREQ
ZAHP:ET,:::; Show all ET's that are in alarm FREQUENCIES:
Taking an ET out of Seperated State 32 47
ZUSC:ET,#:SE; Will place the ET in a Separated - No Hardware state
(SE-NH) MAIO VALUES PER RADIO TI
Status session for User ID and commands:
ZIGO: Displays commands run for BSC on specific date and time.
Reloading software on a site: ADM. OP.
ZEWV:BCF #:BU; Reloads the software on a BCF STATE STATE FREQ RTSL

TRX-008 L BL-USR -
TRX-009 U WO 56 BCC
TRX-011 U WO 0
TRX-012 U WO 1

*) NOT RELEVANT IN THIS H

COMMAND EXECUTED
TRX-008 L BL-USR -
TRX-009 U WO 56 BCC
TRX-011 U WO 0
TRX-012 U WO 1

*) NOT RELEVANT IN THIS H

COMMAND EXECUTED

BASE TRANSCEIVER STATION

<

MABASE STATION CONTROL

<

MAIN LEVEL COMMAND <_

< EQO:BTS=15:HOP;
LOADING PROGRAM VERSIO

BSC3i BDVL01 2

FREQUENCY HOPPING PARA

=======================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDB
-------------------------------------
BTS ADMINISTRATIVE STATE
BTS OPERATIONAL STATE ....

BTS HOPPING MODE...........

HOPPING SEQUENCE NUM
HOPPING SEQUENCE NUM
MAIO OFFSET....................
MAIO STEP......................(M
MOBILE ALLOCATION FREQ
FREQUENCIES:
32 47

MAIO VALUES PER RADIO TI

ADM. OP.
STATE STATE FREQ RTSL

TRX-008 L BL-USR -
TRX-009 U WO 56 BCC
TRX-011 U WO 0
TRX-012 U WO 1

*) NOT RELEVANT IN THIS H

COMMAND EXECUTED

BASE TRANSCEIVER STATION

<

MAIN LEVEL COMMAND <_

< EQO:BTS=14:HOP;

LOADING PROGRAM VERSIO

BSC3i BDVL01 2

FREQUENCY HOPPING PARA

<

MAIN LEVEL COMMAND <_

< EQO:BTS=14:HOP;

LOADING PROGRAM VERSIO

BSC3i BDVL01 2

FREQUENCY HOPPING PARA

=======================

SEG-0014 TNDBKL012
BCF-0005 BTS-0014 TNDB
-------------------------------------
BTS ADMINISTRATIVE STATE
BTS OPERATIONAL STATE ....

BTS HOPPING MODE...........

HOPPING SEQUENCE NUM
HOPPING SEQUENCE NUM
MAIO OFFSET....................
MAIO STEP......................(M
MOBILE ALLOCATION FREQ
FREQUENCIES:
40 44

MAIO VALUES PER RADIO TI

ADM. OP.
STATE STATE FREQ RTSL

TRX-005 U WO 58 BCC
TRX-006 U WO 0

*) NOT RELEVANT IN THIS H

COMMAND EXECUTED

BASE TRANSCEIVER STATION

<

MAIN LEVEL COMMAND <_

< EQO:BTS=13:HOP;

LOADING PROGRAM VERSIO

BSC3i BDVL01 2

FREQUENCY HOPPING PARA

=======================

SEG-0013 TNDBKL011
BCF-0005 BTS-0013 TNDB
-------------------------------------
BTS ADMINISTRATIVE STATE
BTS OPERATIONAL STATE ....

BTS HOPPING MODE...........

HOPPING SEQUENCE NUM
HOPPING SEQUENCE NUM
MAIO OFFSET....................
MAIO STEP......................(M
MOBILE ALLOCATION FREQ
FREQUENCIES:
49 52

MAIO VALUES PER RADIO TI

BTS HOPPING MODE...........
HOPPING SEQUENCE NUM
HOPPING SEQUENCE NUM
MAIO OFFSET....................
MAIO STEP......................(M
MOBILE ALLOCATION FREQ
FREQUENCIES:
49 52

MAIO VALUES PER RADIO TI

ADM. OP.
STATE STATE FREQ RTSL

TRX-001 U WO 60 BCC
TRX-002 U WO 0
TRX-003 U WO 1

*) NOT RELEVANT IN THIS H

COMMAND EXECUTED

*/
EQS:BTS=15:L

/* ENTER FORCED HANDOV

FHO ... FORCED HANDOVE

DEFAULT IS THAT BTS IS SE

EQS:BTS=15:L:FHO

/* IDENTIFY TIME LIMIT OF

DECIMAL NUMBER 1 ... 5

DEFAULT IS 300 SECONDS

EQS:BTS=15:L:FHO,5;

NOTE! BTS LOCK/UNLOCK

EXECUTION STARTED

BSC3i BDVL01 2

BTS ADMINISTRATIVE STATE

=======================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDB
-------------------------------------
BTS ADMINISTRATIVE STATE
BTS OPERATIONAL STATE ....

BSC DATABASE UPDATED

COMMAND EXECUTED

BASE TRANSCEIVER STATION

< ZEBT

LOADING PROGRAM VERSIO

BSC DATABASE UPDATED

COMMAND EXECUTED

BASE TRANSCEIVER STATION

< ZEBT

LOADING PROGRAM VERSIO

/* DATA UNITS:

USE OF THE FREQUENCY L

IDENTIFICATION OF MOBI
IDENTIFICATION OF FUNCT
FREQUENCY;

MAIN LEVEL COMMAND <_

< EBT:MAL

LOADING PROGRAM VERSIO

/* IDENTIFY MOBILE ALLOCA

DECIMAL NUMBER 1 ... 42

PARAMETER IS OBLIGATOR

EBT:MAL,790

/* IDENTIFY THE IDENTIFICA

A ... ADD FREQUENCY

R ... REMOVE FREQUENCY

PARAMETER IS OBLIGATOR

EBT:MAL,790,A

/* IDENTIFY FREQUENCIES:

PARAMETER NAME:

FREQ ... FREQUENCY (&)

PARAMETER IS OBLIGATO

EBT:MAL,790,A:FREQ

/* IDENTIFY FREQUENCIES:

DECIMAL NUMBER(S) (&)

E-GSM: 975 .

ONE MOBILE ALLOCATION

EBT:MAL,790,A:FREQ=50;

EXECUTION STARTED

BSC3i BDVL01 2

MOBILE ALLOCATION FREQU

ADDED FREQUENCIES 50
BSC3i BDVL01 2

MOBILE ALLOCATION FREQU

ADDED FREQUENCIES 50

TO

LIST - 790

COMMAND EXECUTED

FREQUENCY LIST AND GPRS

< ZERS

LOADING PROGRAM VERSIO

/* DATA UNITS:

BTS IDENTIFICATION, BTS N

TRX IDENTIFICATION WITH
ADMINISTRATIVE STATE: F

ERS:BTS
/* IDENTIFY BASE TRANSCEI

DECIMAL NUMBER 1 ... 6

PARAMETER IS OBLIGATOR

ERS:BTS=15

/* IDENTIFY TRANSCEIVER O

PARAMETER NAMES:

BTS ..... BASE TRANSCEIVE

NAME .... BASE TRANSCEI
TRX ..... TRANSCEIVER IDE
IFREQ ... TRANSCEIVER ID
CH ..... RADIO TIME SLOT

BTS AND NAME ARE ALTE

TRX AND IFREQ ARE ALTE

ERS:BTS=15,TRX

/* IDENTIFY TRANSCEIVER (

DECIMAL NUMBER 1 ... 3

PARAMETER IS OBLIGATOR

ERS:BTS=15,TRX=8

/* IDENTIFY TRANSCEIVER O

PARAMETER NAMES:

BTS ..... BASE TRANSCEIVE

NAME .... BASE TRANSCEI
TRX ..... TRANSCEIVER IDE
IFREQ ... TRANSCEIVER ID
CH ..... RADIO TIME SLOT
ERS:BTS=15,TRX=8

/* IDENTIFY TRANSCEIVER O

PARAMETER NAMES:

BTS ..... BASE TRANSCEIVE

NAME .... BASE TRANSCEI
TRX ..... TRANSCEIVER IDE
IFREQ ... TRANSCEIVER ID
CH ..... RADIO TIME SLOT

BTS AND NAME ARE ALTE

TRX AND IFREQ ARE ALTE

ERS:BTS=15,TRX=8:U;

BSC3i BDVL01 2

EXECUTION STARTED

ADMINISTRATIVE STATE CHA

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBK
COMMAND EXECUTED

EQS:BTS

/* IDENTIFY BASE TRANSCEI

DECIMAL NUMBER 1 ... 6

EQS:BTS=15

/* GIVE ADMINISTRATIVE ST

L ... LOCKED STATE

U ... UNLOCKED STATE

PARAMETER IS OBLIGATOR

EQS:BTS=15:U;

NOTE! BTS LOCK/UNLOCK

EXECUTION STARTED

BSC3i BDVL01 2

BTS ADMINISTRATIVE STATE

=======================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDB
-------------------------------------
BTS ADMINISTRATIVE STATE
BTS OPERATIONAL STATE ....

BSC DATABASE UPDATED

=======================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDB
-------------------------------------
BTS ADMINISTRATIVE STATE
BTS OPERATIONAL STATE ....

BSC DATABASE UPDATED

COMMAND EXECUTED

BASE TRANSCEIVER STATION

<

MAIN LEVEL COMMAND <_

< ZDTI

LOADING PROGRAM VERSIO

/* DATA UNITS:

D-CHANNEL LINK SET NAM

UNIT TYPE, UNIT INDEX:
ADDITIONAL FILTERING OP
ADDITIONAL FILTERING OP

DTI:::PCM

/* IDENTIFY EXTERNAL PCM

DECIMAL NUMBER (&&) 0

DEFAULT IS ALL D-CHANNE

DTI:::PCM=266;

BSC3i BDVL01 2

INTERROGATING D-CHANNE

INTERFACE EXT
NAME NUM UNIT SIDE
----- --- ------- --------- -------
OM005 20 BCSU-1 NETW
T0051 21 BCSU-4 NETW
T0052 22 BCSU-3 NETW
T0503 23 BCSU-5 NETW
T0508 311 BCSU-1 NETW

COMMAND EXECUTED
MAL fre addition

PRIMARY RATE ACCESS D-CHANNEL STATE MANAGEMENT COMMAND <DT_>

< ZERS:BTS=15,TRX=8:U;

LOADING PROGRAM VERSION 34.1-0

BSC3i BDVL01 2017-10-02 17:54:53

EXECUTION STARTED

ADMINISTRATIVE STATE CHANGE

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBKL013 TRX-008 NOT SUCCEEDED
/*** DX ERROR: 11259 ***/
/*** TOO FEW ARFCNS IN MA LIST USED BY CELL ***/
COMMAND EXECUTION FAILED

TRANSCEIVER DATA HANDLING COMMAND <ER_>

<

BASE STATION CONTROLLER HANDLING COMMAND <EE_>

< ZEQO

LOADING PROGRAM VERSION 34.13-0

/* DATA UNITS:

BTS IDENTIFICATION, BTS NAME, LOCATION AREA CODE, CELL IDENTIFICATION,

SEG IDENTIFICATION, SEG NAME: PARAMETER GROUP ; */

EQO:BTS

/* IDENTIFY BASE TRANSCEIVER STATION (BTS):

DECIMAL NUMBER 1 ... 660 ( &, && ) */

EQO:BTS=15

/* GIVE PARAMETER GROUP

IDE ... BTS IDENTIFICATION PARAMETERS

CEL ... CELL ACCESS PARAMETERS
RAD ... RADIO LINK CONTROL DL PARAMETERS
QUE ... QUEUEING PARAMETERS
CCH ... CCH CONFIGURATION PARAMETERS
INT ... INTERFERENCE AVERAGING PARAMETERS
MIS ... MISCELLANEOUS PARAMETERS
HOP ... FREQUENCY HOPPING PARAMETERS
BCC ... BCCH FREQUENCY LIST USAGE PARAMETERS
TRU ... TRUNK RESERVATION PARAMETERS
GPRS .. GPRS PARAMETERS
GPC ... GPRS CONTROL PARAMETERS
DAT ... DATA SERVICE PARAMETERS
AMR ... AMR PARAMETERS
ALL ... ALL PARAMETERS
 MIS ... MISCELLANEOUS PARAMETERS
HOP ... FREQUENCY HOPPING PARAMETERS
BCC ... BCCH FREQUENCY LIST USAGE PARAMETERS
TRU ... TRUNK RESERVATION PARAMETERS
GPRS .. GPRS PARAMETERS
GPC ... GPRS CONTROL PARAMETERS
DAT ... DATA SERVICE PARAMETERS
AMR ... AMR PARAMETERS
ALL ... ALL PARAMETERS

DEFAULT IS IDE GROUP */

EQO:BTS=15:

/* GIVE PARAMETER GROUP

IDE ... BTS IDENTIFICATION PARAMETERS

CEL ... CELL ACCESS PARAMETERS
RAD ... RADIO LINK CONTROL DL PARAMETERS
QUE ... QUEUEING PARAMETERS
CCH ... CCH CONFIGURATION PARAMETERS
INT ... INTERFERENCE AVERAGING PARAMETERS
MIS ... MISCELLANEOUS PARAMETERS
HOP ... FREQUENCY HOPPING PARAMETERS
BCC ... BCCH FREQUENCY LIST USAGE PARAMETERS
TRU ... TRUNK RESERVATION PARAMETERS
GPRS .. GPRS PARAMETERS
GPC ... GPRS CONTROL PARAMETERS
DAT ... DATA SERVICE PARAMETERS
AMR ... AMR PARAMETERS
ALL ... ALL PARAMETERS

DEFAULT IS IDE GROUP */

EQO:BTS=15:HOP;

BSC3i BDVL01 2017-10-02 18:00:15

FREQUENCY HOPPING PARAMETERS:

=============================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBKL013
-------------------------------------
BTS ADMINISTRATIVE STATE ... UNLOCKED
BTS OPERATIONAL STATE ...... WO

BTS HOPPING MODE..................(HOP).... RF (RF HOPPING)

HOPPING SEQUENCE NUMBER 1......(HSN1)... 11
HOPPING SEQUENCE NUMBER 2......(HSN2)... 0 *)
MAIO OFFSET....................(MO)..... 0
MAIO STEP......................(MS)..... 1
MOBILE ALLOCATION FREQ LIST....(MAL).... 790
FREQUENCIES:
32 47

MAIO VALUES PER RADIO TIMESLOT:

ADM. OP.
STATE STATE FREQ RTSL0 RTSL1 RTSL2 RTSL3 RTSL4 RTSL5 RTSL6 RTSL7

TRX-008 L BL-USR - - - - - - - -
TRX-009 U WO 56 BCCH - - - - - - -
TRX-011 U WO 0 0 0 0 0 0 0 0
TRX-012 U WO 1 1 1 1 1 1 1 1

*) NOT RELEVANT IN THIS HOPPING MODE

COMMAND EXECUTED
TRX-008 L BL-USR - - - - - - - -
TRX-009 U WO 56 BCCH - - - - - - -
TRX-011 U WO 0 0 0 0 0 0 0 0
TRX-012 U WO 1 1 1 1 1 1 1 1

*) NOT RELEVANT IN THIS HOPPING MODE

COMMAND EXECUTED

BASE TRANSCEIVER STATION HANDLING IN BSC COMMAND <EQ_>

<

MABASE STATION CONTROLLER HANDLING COMMAND <EE_>

<

MAIN LEVEL COMMAND <___>

< EQO:BTS=15:HOP;
LOADING PROGRAM VERSION 34.13-0

BSC3i BDVL01 2017-10-02 18:02:32

FREQUENCY HOPPING PARAMETERS:

=============================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBKL013
-------------------------------------
BTS ADMINISTRATIVE STATE ... UNLOCKED
BTS OPERATIONAL STATE ...... WO

BTS HOPPING MODE..................(HOP).... RF (RF HOPPING)

HOPPING SEQUENCE NUMBER 1......(HSN1)... 11
HOPPING SEQUENCE NUMBER 2......(HSN2)... 0 *)
MAIO OFFSET....................(MO)..... 0
MAIO STEP......................(MS)..... 1
MOBILE ALLOCATION FREQ LIST....(MAL).... 790
FREQUENCIES:
32 47

MAIO VALUES PER RADIO TIMESLOT:

ADM. OP.
STATE STATE FREQ RTSL0 RTSL1 RTSL2 RTSL3 RTSL4 RTSL5 RTSL6 RTSL7

TRX-008 L BL-USR - - - - - - - -
TRX-009 U WO 56 BCCH - - - - - - -
TRX-011 U WO 0 0 0 0 0 0 0 0
TRX-012 U WO 1 1 1 1 1 1 1 1

*) NOT RELEVANT IN THIS HOPPING MODE

COMMAND EXECUTED

BASE TRANSCEIVER STATION HANDLING IN BSC COMMAND <EQ_>

<

MAIN LEVEL COMMAND <___>

< EQO:BTS=14:HOP;

LOADING PROGRAM VERSION 34.13-0

BSC3i BDVL01 2017-10-02 18:02:46

FREQUENCY HOPPING PARAMETERS:

<

MAIN LEVEL COMMAND <___>

< EQO:BTS=14:HOP;

LOADING PROGRAM VERSION 34.13-0

BSC3i BDVL01 2017-10-02 18:02:46

FREQUENCY HOPPING PARAMETERS:

=============================

SEG-0014 TNDBKL012
BCF-0005 BTS-0014 TNDBKL012
-------------------------------------
BTS ADMINISTRATIVE STATE ... UNLOCKED
BTS OPERATIONAL STATE ...... WO

BTS HOPPING MODE..................(HOP).... RF (RF HOPPING)

HOPPING SEQUENCE NUMBER 1......(HSN1)... 11
HOPPING SEQUENCE NUMBER 2......(HSN2)... 0 *)
MAIO OFFSET....................(MO)..... 0
MAIO STEP......................(MS)..... 1
MOBILE ALLOCATION FREQ LIST....(MAL).... 789
FREQUENCIES:
40 44

MAIO VALUES PER RADIO TIMESLOT:

ADM. OP.
STATE STATE FREQ RTSL0 RTSL1 RTSL2 RTSL3 RTSL4 RTSL5 RTSL6 RTSL7

TRX-005 U WO 58 BCCH - - - - - - -
TRX-006 U WO 0 0 0 0 0 0 0 0

*) NOT RELEVANT IN THIS HOPPING MODE

COMMAND EXECUTED

BASE TRANSCEIVER STATION HANDLING IN BSC COMMAND <EQ_>

<

MAIN LEVEL COMMAND <___>

< EQO:BTS=13:HOP;

LOADING PROGRAM VERSION 34.13-0

BSC3i BDVL01 2017-10-02 18:02:55

FREQUENCY HOPPING PARAMETERS:

=============================

SEG-0013 TNDBKL011
BCF-0005 BTS-0013 TNDBKL011
-------------------------------------
BTS ADMINISTRATIVE STATE ... UNLOCKED
BTS OPERATIONAL STATE ...... WO

BTS HOPPING MODE..................(HOP).... RF (RF HOPPING)

HOPPING SEQUENCE NUMBER 1......(HSN1)... 11
HOPPING SEQUENCE NUMBER 2......(HSN2)... 0 *)
MAIO OFFSET....................(MO)..... 0
MAIO STEP......................(MS)..... 1
MOBILE ALLOCATION FREQ LIST....(MAL).... 788
FREQUENCIES:
49 52

MAIO VALUES PER RADIO TIMESLOT:

BTS HOPPING MODE..................(HOP).... RF (RF HOPPING)
HOPPING SEQUENCE NUMBER 1......(HSN1)... 11
HOPPING SEQUENCE NUMBER 2......(HSN2)... 0 *)
MAIO OFFSET....................(MO)..... 0
MAIO STEP......................(MS)..... 1
MOBILE ALLOCATION FREQ LIST....(MAL).... 788
FREQUENCIES:
49 52

MAIO VALUES PER RADIO TIMESLOT:

ADM. OP.
STATE STATE FREQ RTSL0 RTSL1 RTSL2 RTSL3 RTSL4 RTSL5 RTSL6 RTSL7

TRX-001 U WO 60 BCCH - - - - - - -
TRX-002 U WO 0 0 0 0 0 0 0 0
TRX-003 U WO 1 1 1 1 1 1 1 1

*) NOT RELEVANT IN THIS HOPPING MODE

COMMAND EXECUTED

*/
EQS:BTS=15:L

/* ENTER FORCED HANDOVER

FHO ... FORCED HANDOVER

DEFAULT IS THAT BTS IS SET TO LOCKED STATE IMMEDIATELY */

EQS:BTS=15:L:FHO

/* IDENTIFY TIME LIMIT OF FORCED HANDOVER

DECIMAL NUMBER 1 ... 500 SECONDS

DEFAULT IS 300 SECONDS */

EQS:BTS=15:L:FHO,5;

NOTE! BTS LOCK/UNLOCK WILL TAKE MAXIMUM OF 7 MINUTES

EXECUTION STARTED

BSC3i BDVL01 2017-10-02 18:06:55

BTS ADMINISTRATIVE STATE CHANGED:

=================================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBKL013
-------------------------------------
BTS ADMINISTRATIVE STATE ... SHUTTING DOWN
BTS OPERATIONAL STATE ...... BL-USR

BSC DATABASE UPDATED

COMMAND EXECUTED

BASE TRANSCEIVER STATION HANDLING IN BSC COMMAND <EQ_>

< ZEBT

LOADING PROGRAM VERSION 30.3-0

BSC DATABASE UPDATED

COMMAND EXECUTED

BASE TRANSCEIVER STATION HANDLING IN BSC COMMAND <EQ_>

< ZEBT

LOADING PROGRAM VERSION 30.3-0

/* DATA UNITS:

USE OF THE FREQUENCY LIST,

IDENTIFICATION OF MOBILE ALLOCATION FREQUENCY LIST,
IDENTIFICATION OF FUNCTION:
FREQUENCY; */

MAIN LEVEL COMMAND <___>

< EBT:MAL

LOADING PROGRAM VERSION 30.3-0

/* IDENTIFY MOBILE ALLOCATION FREQUENCY LIST:

DECIMAL NUMBER 1 ... 4200 ( &, && )

PARAMETER IS OBLIGATORY */

EBT:MAL,790

/* IDENTIFY THE IDENTIFICATION OF FUNCTION:

A ... ADD FREQUENCY

R ... REMOVE FREQUENCY

PARAMETER IS OBLIGATORY */

EBT:MAL,790,A

/* IDENTIFY FREQUENCIES:

PARAMETER NAME:

FREQ ... FREQUENCY (&)

PARAMETER IS OBLIGATORY */

EBT:MAL,790,A:FREQ

/* IDENTIFY FREQUENCIES:

DECIMAL NUMBER(S) (&) P-GSM: 1 ... 124

E-GSM: 975 ... 1023, 0

ONE MOBILE ALLOCATION LIST CAN EITHER CONTAIN P-GSM OR E-GSM FREQUENCIES */

EBT:MAL,790,A:FREQ=50;

EXECUTION STARTED

BSC3i BDVL01 2017-10-02 18:08:16

MOBILE ALLOCATION FREQUENCY LIST MODIFIED

ADDED FREQUENCIES 50
BSC3i BDVL01 2017-10-02 18:08:16

MOBILE ALLOCATION FREQUENCY LIST MODIFIED

ADDED FREQUENCIES 50

TO

LIST - 790

COMMAND EXECUTED

FREQUENCY LIST AND GPRS OBJECTS HANDLING COMMAND <EB_>

< ZERS

LOADING PROGRAM VERSION 34.1-0

/* DATA UNITS:

BTS IDENTIFICATION, BTS NAME, TRANSCEIVER IDENTIFICATION,

TRX IDENTIFICATION WITH FREQUENCY, RTSL IDENTIFICATION:
ADMINISTRATIVE STATE: FORCED HANDOVER, TIME LIMIT; */

ERS:BTS
/* IDENTIFY BASE TRANSCEIVER STATION (BTS):

DECIMAL NUMBER 1 ... 660

PARAMETER IS OBLIGATORY, IF NAME IS NOT GIVEN */

ERS:BTS=15

/* IDENTIFY TRANSCEIVER OR RADIO TIME SLOT:

PARAMETER NAMES:

BTS ..... BASE TRANSCEIVER STATION IDENTIFICATION

NAME .... BASE TRANSCEIVER STATION NAME
TRX ..... TRANSCEIVER IDENTIFICATION ( &,&& )
IFREQ ... TRANSCEIVER IDENTIFICATION WITH FREQUENCY ( & )
CH ..... RADIO TIME SLOT IDENTIFICATION ( &,&& )

BTS AND NAME ARE ALTERNATIVE

TRX AND IFREQ ARE ALTERNATIVE */

ERS:BTS=15,TRX

/* IDENTIFY TRANSCEIVER (TRX):

DECIMAL NUMBER 1 ... 36 ( &, && )

PARAMETER IS OBLIGATORY, IF IFREQ IS NOT GIVEN */

ERS:BTS=15,TRX=8

/* IDENTIFY TRANSCEIVER OR RADIO TIME SLOT:

PARAMETER NAMES:

BTS ..... BASE TRANSCEIVER STATION IDENTIFICATION

NAME .... BASE TRANSCEIVER STATION NAME
TRX ..... TRANSCEIVER IDENTIFICATION ( &,&& )
IFREQ ... TRANSCEIVER IDENTIFICATION WITH FREQUENCY ( & )
CH ..... RADIO TIME SLOT IDENTIFICATION ( &,&& )
ERS:BTS=15,TRX=8

/* IDENTIFY TRANSCEIVER OR RADIO TIME SLOT:

PARAMETER NAMES:

BTS ..... BASE TRANSCEIVER STATION IDENTIFICATION

NAME .... BASE TRANSCEIVER STATION NAME
TRX ..... TRANSCEIVER IDENTIFICATION ( &,&& )
IFREQ ... TRANSCEIVER IDENTIFICATION WITH FREQUENCY ( & )
CH ..... RADIO TIME SLOT IDENTIFICATION ( &,&& )

BTS AND NAME ARE ALTERNATIVE

TRX AND IFREQ ARE ALTERNATIVE */

ERS:BTS=15,TRX=8:U;

BSC3i BDVL01 2017-10-02 18:09:21

EXECUTION STARTED

ADMINISTRATIVE STATE CHANGE

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBKL013 TRX-008 UNLOCKED
COMMAND EXECUTED

EQS:BTS

/* IDENTIFY BASE TRANSCEIVER STATION (BTS):

DECIMAL NUMBER 1 ... 660 */

EQS:BTS=15

/* GIVE ADMINISTRATIVE STATE

L ... LOCKED STATE

U ... UNLOCKED STATE

PARAMETER IS OBLIGATORY */

EQS:BTS=15:U;

NOTE! BTS LOCK/UNLOCK WILL TAKE MAXIMUM OF 7 MINUTES

EXECUTION STARTED

BSC3i BDVL01 2017-10-02 18:10:01

BTS ADMINISTRATIVE STATE CHANGED:

=================================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBKL013
-------------------------------------
BTS ADMINISTRATIVE STATE ... UNLOCKED
BTS OPERATIONAL STATE ...... BL-RST

BSC DATABASE UPDATED

=================================

SEG-0015 TNDBKL013
BCF-0005 BTS-0015 TNDBKL013
-------------------------------------
BTS ADMINISTRATIVE STATE ... UNLOCKED
BTS OPERATIONAL STATE ...... BL-RST

BSC DATABASE UPDATED

COMMAND EXECUTED

BASE TRANSCEIVER STATION HANDLING IN BSC COMMAND <EQ_>

<

MAIN LEVEL COMMAND <___>

< ZDTI

LOADING PROGRAM VERSION 9.3-0

/* DATA UNITS:

D-CHANNEL LINK SET NAME(S) OR NUMBER(S):

UNIT TYPE, UNIT INDEX:
ADDITIONAL FILTERING OPTION (PCM AND SAPI):
ADDITIONAL FILTERING OPTION (WORKING STATE); */

DTI:::PCM

/* IDENTIFY EXTERNAL PCM NUMBER(S) OF D-CHANNELS:

DECIMAL NUMBER (&&) 0 ... 2048

DEFAULT IS ALL D-CHANNELS */

DTI:::PCM=266;

BSC3i BDVL01 2017-10-02 18:10:53

INTERROGATING D-CHANNEL WORKING STATE

INTERFACE EXT SUB WORKING

NAME NUM UNIT SIDE PCM-TSL-TSL SAPI STATE
----- --- ------- --------- ----------- ---- -------
OM005 20 BCSU-1 NETW 266-31-04 62 WO-EX
T0051 21 BCSU-4 NETW 266-13-00 0 WO-EX
T0052 22 BCSU-3 NETW 266-13-04 0 WO-EX
T0503 23 BCSU-5 NETW 266-14-00 0 WO-EX
T0508 311 BCSU-1 NETW 266-09-00 0 BL-SY

COMMAND EXECUTED
Baseband bacckup and restore process

The Site Engineer reaches the site with the Backup and the software / upgrade package as noted
during the CV creation.

The new hardware installed on the site is powered on. The laptop is configured with an IP
address of
169.254.2.1,
a subnet mask of
255.255.255.0 and a default gateway of 169.254.2.2.

From the web browser of the Laptop, the following URL is accessed.

https://169.254.2.2/autointegration.html

https://169.254.2.2/ea.html
for board restore

The attached Summary File is used to define the correct Software Package Zip File and the
Backup Name. The software package and the summary file itself should be present in the Folder
as defined on the SFTP server. After this proceed to “download files”.

The sample summary file is attached

Once the files are download the node is ready to log in. Install License Key File. The node is
ready to be brought into service.

---------------------------------------------------------------------------------------------------------------------------
-> connect cisco VPN pass :Raj@12345

->winfoil username : SainiA9@RAJ-OSS-vraj1uas2x-ssh

Pass :)QnaL_9sg7;V8E$

for 3G/4G site amos LMTOK0008

For BSC Login eaw RBSKO01

NOKIA BSC
PUTTY
10.19.72.30
PORT 48152
NEVER

LOGIAN AS : KhandelwalS
pass :june@2018

Ne Id :- list *RAJ

For TCU SSH [email protected]

pass hidden

---------------------------------------------------------------------------------------------------------------------------

Coriant Funda

Laptop Ip 169.254.0.2
subnet default

Google chrome https://169.254.0.1 enter

pass hidden

---------------------------------------------------------------------------------------------------------------------------

Coriant Funda

Laptop Ip 169.254.0.2
subnet default

Google chrome https://169.254.0.1 enter

Username :Administrator

Pass :e2e!Net4u#

for power check

configurator ---> optical power

-------------------------------------------------------------------------------------------------------------------------------
-
e as noted

n IP

the
he Folder

de is

---------

Baseband pass WebeX_User123$

---------
---------

-------------
Nokia BSC backup through winscp

172.32.172.31
255.255.255.0
172.32.172.32

BSC ftp port MCMU0 Ist ESB port 25

Ericsson Bsc Backup

192.168.200.2
255.255.255.0
192.168.200.1

BG20 Boot configuration IP

192.100.XX.XX

LCT BGF IP for BG20 Login

Laptop 194.194.194.100 255.255.255.0
Login IP 194.194.194.193
Pass sdh123456
rc102616nms\alv1user
Secure123!