Spillwaysfinalppt 180319085104

By
G.Rajkumar
315126508063
Civil III/IV
ANITS
Contents
Introduction
Requirements of spillway
Location of spillway
Component parts of spillway
Types of spillways
Conclusion
References
INTRODUCTION :
A passageway through which surplus water escapes from a
reservoir, lake, or the like.
Discharges the flood water to downstream of river without

overtopping the dam.
A structure which will not let the water rise above the
maximum reservoir level.
A spillway is essentially a safety valve for a dam.

Requirements of Spillway :
 Provide structural stability to dam under all conditions.
Able to pass the designed flood without raising the water

level above H.F.L.
Safe disposal of water without toe erosion.
Should have an efficient operation.
Should be economical.
Location of Spillway :
Within the body of the dam
At one end of dam.
Entirely away from it, independently in a saddle.

Component parts of Spillway :
Approach channel
Control structure
Discharge carrier
Discharge channel
Energy dissipators.
Approach channel
Entrance structure or the path to draw water from reservoir and

convey it to the control structure.
It may be straight or curved in plan.
Its banks may be parallel, convergent, divergent or

combination of these and may be vertical or sloping.
It may insure minimum head loss through the channel and to
obtain uniformity of flow over the control structure.
APPROACH CHANNEL
Control structure
Major component of spillway provided with bridge and

gates.
Regulates and controls the surplus water from the reservoir.
It does not allow discharge of water below the fixed

reservoir level.
Control structure
Discharge carrier
 It is the waterway provided to convey the flows released

from the control structure to the downstream side of
spillway.
The cross section may be rectangular, trapezoidal or of

other shape.
Waterway may be wide or narrow, long or short.

Discharge
carrier
Discharge channel
Provided to convey the water from bottom of the
discharge carrier to the downstream flowing river.
It may be the downstream face of spillway itself.
The width of discharge channel depends on amount of

water to be conveyed.
Discharge channel
Energy dissipators
At the end of discharge carrier, the water released from

control structure has great velocities enough to cause scour.
Thus, energy dissipators are provided to avoid the scouring

of downstream side of spillway.
These are to be provided before water entering the discharge

channel.
The following are the different types of dissipators:

1. Bucket type energy dissipators
2. Stilling basin type dissipators
3. Baffle type dissipators.
Bucket type dissipators
 The high kinetic energy of water is reduced by providing

a hydraulic jump at the end of spillway.
 The hydraulic jump can be achieved by providing bucket

type dissipators.
By hydraulic jump of water some part of energy is

dissipated by aeration.
Bucket type dissipator
Stilling basin
Stilling basins are usually provided after the buckets.
Due to the hydraulic jump of water, the water falling on

the ground may cause cavitations on the ground.
These cavitations can be avoided by providing the stilling

basin.
The stilling basin consists of water which reduces some

part of energy of water.
Stilling basin
Baffle type dissipators
After passing the stilling basin water has still some energy.
If any amount of energy exist, it can be fully dissipated by

providing baffle dissipators.
In this, baffle type structures are provided in a number of

series depending on the amount of energy.
Baffle type dissipators
Types of Spillways :
Straight drop spillway
Overflow spillway
Chute spillway
Side channel spillway
Shaft spillway
Syphon spillway
Straight drop Spillway
In this type of spillway, the water freely drops down from
the crest.
It is a low weir and simple vertical fall type structures.
The water falls freely from the crest under the action of
gravity.
To prevent scouring at the downstream, an auxiliary dam of

artificial pool is to be constructed at the place of fall of
water.
Straight drop spillway
Overflow spillway
It is generally known as Ogee spillway.
It represents the S-shape curve so, it is called ogee

spillway.
It is an improved form of straight drop spillway.
It is mainly used in gravity dams.
It has got the advantage over other spillways for its high
discharging efficiency.
Ogee spillway
Chute spillway
It is often called as trough or open channel spillway.
For earthen and rockfill dams, spillway is to be constructed

separately away from the main valley.
 Chute Spillway is the simplest type of a spillway which can

be easily provided independently and at low costs.
It is lighter and adaptable to any type of foundations.

Chute spillway
Side channel spillway
The flow in this spillway is turned 90 ̊ after passing the

crest such that the flow is parallel to the weir crest.
Best suitable for non rigid dams like earthen dams.
It is preferred where space is not available for providing

sufficient crest width for chute spillway.
The discharge carrier may be an open channel type or a

conduit type.
Side channel spillway
Shaft spillway
The water from the reservoir enters into a vertical shaft

which conveys this water into a horizontal tunnel which
finally discharges the water into the river downstream.
This type of spillway is preferred where the space is not

available for providing the above type of spillways
If the inlet leg is provided in shape of a funnel, it is called

Morning Glory Spillway.
It has maximum discharge even at low heads.

Shaft spillway
Syphon spillway
It works on the principle of syphonic action.
It consists of a syphon pipe whose inlet leg is kept just below
the normal pool level and an air vent kept at normal pool
level is connected to the crown of syphon.
When the water raises the pool level, syphonic action starts
automatically and the water discharges to downstream side.
When the water level falls below the pool level, air is entered
through air vent and the discharging of water stops.
Syphon spillway
Conclusion
Straight drop spillway is suitable for arch dams and for small
drops.
Ogee spillway is the most commonly used spillway for its high
discharging efficiency.
Chute spillway can be provided in any type of foundation.
Side channel spillways are hydraulically less efficient.
Shaft spillway becomes undesirable where a discharge more

than the design capacity is to be passed.
 syphon spillway is an automatically operated type spillway.

References
 Water resources engineering by S.K.Garg
 Module 4 - Hydraulic Structures for Flow Diversion and Storage Version

2 - Lesson 8 Spillways and Energy Dissipators - NPTEL
 Frizell, K. H. . Hydraulics of Spillways for RCC Dams and Dam

Rehabilitations. Proc. of the 3rd Specialty Conf. on Roller Compacted
Concrete. pp.423–439. San Diego, CA, , USA: ASCE.
THANK
YOU...

Spillwaysfinalppt 180319085104

Uploaded by

Copyright:

Available Formats

Spillwaysfinalppt 180319085104

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Spillwaysfinalppt 180319085104

Uploaded by

Copyright:

Available Formats

By

Component parts of spillway

Discharges the flood water to downstream of river without

A spillway is essentially a safety valve for a dam.

Able to pass the designed flood without raising the water

Safe disposal of water without toe erosion.

Should have an efficient operation.

At one end of dam.

Entirely away from it, independently in a saddle.

Entrance structure or the path to draw water from reservoir and

It may be straight or curved in plan.

Its banks may be parallel, convergent, divergent or

Major component of spillway provided with bridge and

Regulates and controls the surplus water from the reservoir.

It does not allow discharge of water below the fixed

 It is the waterway provided to convey the flows released

The cross section may be rectangular, trapezoidal or of

Waterway may be wide or narrow, long or short.

It may be the downstream face of spillway itself.

The width of discharge channel depends on amount of

At the end of discharge carrier, the water released from

Thus, energy dissipators are provided to avoid the scouring

These are to be provided before water entering the discharge

The following are the different types of dissipators:

 The high kinetic energy of water is reduced by providing

 The hydraulic jump can be achieved by providing bucket

By hydraulic jump of water some part of energy is

Stilling basins are usually provided after the buckets.

Due to the hydraulic jump of water, the water falling on

These cavitations can be avoided by providing the stilling

The stilling basin consists of water which reduces some

If any amount of energy exist, it can be fully dissipated by

In this, baffle type structures are provided in a number of

Straight drop spillway

Side channel spillway

It is a low weir and simple vertical fall type structures.

To prevent scouring at the downstream, an auxiliary dam of

It is generally known as Ogee spillway.

It represents the S-shape curve so, it is called ogee

It is an improved form of straight drop spillway.

It is mainly used in gravity dams.

It is often called as trough or open channel spillway.

For earthen and rockfill dams, spillway is to be constructed

 Chute Spillway is the simplest type of a spillway which can

It is lighter and adaptable to any type of foundations.

The flow in this spillway is turned 90 ̊ after passing the

Best suitable for non rigid dams like earthen dams.

It is preferred where space is not available for providing

The discharge carrier may be an open channel type or a

The water from the reservoir enters into a vertical shaft

This type of spillway is preferred where the space is not

If the inlet leg is provided in shape of a funnel, it is called

It has maximum discharge even at low heads.

It works on the principle of syphonic action.

Chute spillway can be provided in any type of foundation.

Side channel spillways are hydraulically less efficient.

Shaft spillway becomes undesirable where a discharge more

 syphon spillway is an automatically operated type spillway.