Pds Hempel's Shopprimer e 15280 En-Gb

Product Data
HEMPEL'S SHOPPRIMER E 15280
15280: BASE 15289: CURING AGENT 95270

Description: HEMPEL’S SHOPPRIMER E 15280 is a two-component epoxy primer, pigmented with zincphosphate
rust-inhibiting pigments. It is designed for automatic spray application as well as manual application.
Recommended use: As a shopprimer for protection of blast cleaned steel plate and other structural steel during the storage
and building period.
Service temperature: Maximum, dry exposure only: 140°C/284°F
Certificates/Approvals: Complies with European Fire Standard EN 13501-1; classification B-s1, d0.
Availability: Part of Group Assortment. Local availability subject to confirmation.
PHYSICAL CONSTANTS:
Shade nos/Colours: 50890 / Red.
Finish: Flat
Volume solids, %: 22 ± 1
Theoretical spreading rate: 11 m2/l [441.1 sq.ft./US gallon] - 20 micron/0.8 mils
Flash point: -4 °C [24.8 °F]
Specific gravity: 1.1 kg/litre [9.1 lbs/US gallon]
Dry to handle: 5 - 10 minute(s) 20°C/68°F
Fully cured: 7 day(s) 20°C/68°F
VOC content: 659 g/l [5.5 lbs/US gallon]
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 15280
Mixing ratio: BASE 15289: CURING AGENT 95270
2 : 1 by volume
Application method: Airless spray / Air spray / Brush
Thinner (max.vol.): 08570 (20%) / 08570 (20%) / 08450 (20%) see REMARKS overleaf
Pot life: 8 hour(s) 20°C/68°F
Nozzle orifice: 0.021 "
Nozzle pressure: 75 bar [1087.5 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 20 micron [0.8 mils] see REMARKS overleaf
Indicated film thickness, wet: Not relevant
Overcoat interval, min: see REMARKS overleaf
Overcoat interval, max: see REMARKS overleaf
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
Date of issue: July 2017 Page: 1/2

Product Data
HEMPEL'S SHOPPRIMER E 15280
SURFACE PREPARATION: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other contaminants
by high pressure fresh water cleaning. Abrasive blasting to Sa 2½ (ISO 8501-1:2007). Apply
immediately after cleaning. All damage of shopprimer and contamination from storage and fabrication
should be thoroughly cleaned prior to overcoating. For repair and touch-up use: primer specified for
final coating system.
APPLICATION CONDITIONS: Use only where application and curing can proceed at temperatures above: 10°C/50°F. The
temperature of the surface and that of the paint itself must also be above this limit. Maximum steel
temperature approximately: 45°C/113°F. Special measures must be taken for shopprimer applications
at temperatures above app.: 45°C/113°F. (see REMARKS below).
Apply only on a dry and clean surface with a temperature above the dew point to avoid condensation.
In confined spaces provide adequate ventilation during application and drying.
PRECEDING COAT: None.
SUBSEQUENT COAT: According to specification.
REMARKS:
Application equipment:
Film thicknesses/thinning: When applied at higher temperatures extra thinning or use of thinner with slower flash-off time may be
needed to secure proper paint film formation. It is a must that a homogenous and smooth paint film is
obtained.
Recommended dry film thickness: 15 - 25 micron / 0.6 - 1 mils measured on a smooth test panel.
Overcoating: Overcoating intervals related to later conditions of exposure: If the maximum overcoating interval is
exceeded, roughening of the surface is necessary to ensure intercoat adhesion.
Before overcoating after exposure in contaminated environment, clean the surface thoroughly with high
pressure fresh water hosing and allow drying.
A specification supersedes any guideline overcoat intervals indicated in the table.

Environment Atmospheric, medium
Surface temperature: 10°C (50°F) 20°C (68°F) 30°C (86°F)
Min Max Min Max Min Max
HEMPADUR 15 h None 6h None 3h None
Environment Immersion
HEMPADUR 15 h None 6h None 3h None
NR = Not Recommended, Ext. = Extended, m = minute(s), h = hour(s), d = day(s)
Overcoating note: Before overcoating after exposure in contaminated environment, clean the surface thoroughly by high
pressure water cleaning and allow drying.
Overcoating intervals: No maximum overcoat interval for adhesion, but dictated by gradual breakdown and damage during
exposure and fabrication.
Note: HEMPEL'S SHOPPRIMER E 15280 For professional use only.
ISSUED BY: HEMPEL A/S 1528050890
This Product Data Sheet supersedes those previously issued.

For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.
Date of issue: July 2017 Page: 2/2

Pds Hempel's Shopprimer e 15280 En-Gb

Uploaded by

Copyright:

Available Formats

Pds Hempel's Shopprimer e 15280 En-Gb

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Pds Hempel's Shopprimer e 15280 En-Gb

Uploaded by

Copyright:

Available Formats

Product Data

HEMPEL'S SHOPPRIMER E 15280

15280: BASE 15289: CURING AGENT 95270

Date of issue: July 2017 Page: 1/2

A specification supersedes any guideline overcoat intervals indicated in the table.

This Product Data Sheet supersedes those previously issued.

Date of issue: July 2017 Page: 2/2

You might also like