What the numbers mean:

Signal strength is a number ranging from roughly -50 to -105 (your phone
may show as a positive number). Closer to zero means a better signal, i.e. -
CELLULAR PHONE FIELD TEST MODES 50 (roughly full signal) is better than -105 (roughly no signal.)

Apple iPhone HTC DASH, EXCALIBER, S620 (T-Mobile)

In phone mode dial *3001#12345#* then press CALL. Enter *#*#364#*#* and your phone will enter test mode. Signal strength
The Field Test Screen will appear. Select “Cell Information.” follows RSSI. This test mode does not show –dB. Strong signal is 31
Signal Strength is on the top line after RX-. Frequency follows FQ and (approximately -50dBm), weak signal is 4 (approximately -105dBm).
is based on the channel number (i.e. 100-200 is 800 MHz and 500-700 The higher the number (31 vs 4) the better the signal. Press END or
is 1900MHz). The top line displays information about the tower you are Done to exit.
using. The lines below display info about your neighboring towers.
HTC Touch
Audiovox 8300, 8500, 8600, 8615 ##33284#
Press ##2773 then press the END key. Scroll down and select
DEBUG. Signal strength is the 4th line down. (For example Rx: -87). To Kyocera 2035, 2135, 2235, 2255, 5135
exit, press the END key again. Press 111111 (six ones). Select OPTIONS and press MENU (the
upper right hand star button) or OK to select it. Select DEBUG and
Audiovox 8900, 8915, Pantech PN-3200 press MENU or OK. Enter field debug code: 111111 or 000000 (six
Press ##27732726, press END key. Scroll down and select DEBUG. ones or zeros) or 040793. Scroll down to DEBUG SCREEN and press
The signal strength is the 4th line down. (For example Rx-96) MENU or OK. Scroll to BASIC and press MENU or OK. The signal
strength is the last number on the 1st line. To exit the field test, select
Audiovox 9100, 9155 CLOSE and press MENU or OK.
When phone turns on, as soon as green light shuts off, press FCN
(right arrow) and 00. It will ask for FSC Code. Press 000000 (six Kyocera KX1 (SoHo), KX2 (Koi), Kx16 (Candid), 7135
zeroes). Press OK. Highlight DEBUG SCREEN and press FCN, FCN. Press 111111 (six ones). Select OPTIONS, scroll to SERVICE and
Signal strength is the top right number. On 2nd line, if the letter is upper press OK. Scroll down to DEBUG and press OK. Enter 000000 (six
case (for example, “A”), then the phone is on the 1900MHz band. If zeros) and scroll to DEBUG SCREEN, press OK*, select ON and press
lower case (“a”) it is on 800MHz. To exit test mode, turn off phone. OK. Press NEXT and the signal strength is on the 2nd line (for
example, Rx: -87). To exit, press END and follow beginning
Audiovox CDM-9900 instructions to * and select off.
Power the phone off and then back on. Quickly press MENU, 7, *, *.
The FSC Code is 000000 (six zeroes). Press SELECT Key (middle Kyocera K9, 47, 414, 424, 434, 484, 494, 1135, 2325, 2345, 3225
button). Select DEBUG SCREEN. Select NORMAL. Signal strength is Press 111111 (six ones). Select OPTIONS and press OK. Select
on the second line after RX. You may have to dial a fake phone DEBUG and press OK. Enter field debug code: 111111 or 000000 (six
number to get the Rx level to update. Press POWER OFF to exit. ones or zeros) or 040793. Scroll down to DEBUG SCREEN and press
OK. Scroll to ON and press OK, OK, OK. The signal strength is the
Audiovox (UTSTARCOM/HTC) PPC-6600, PPC-6700, XV-6700 first number on the 1st line. To exit the field test, turn off phone.
From the phone screen, press ##33284# or ##33284 and press DIAL.
Signal strength will be after RSSI or RX level. LG LX-350, LX-550 Fusic (Sprint)
Enter ##33284#. Select Service Screen from Debug menu. Signal is
Blackberry after Rx power. Press CLR to exit or power off.
Press TOOLS, SETTINGS, STATUS or OPTIONS, STATUS. This
feature is also available on GSM models. The top line is the signal Note: The Fusic has a special service code that you must get from
strength in –dBm. GSM and iDEN models also have this feature. Sprint.

HP 6315 LG PM-225, PM-325, MM-535, LX5400

Click on START. Select SETTINGS from the drop-down screen. Press ##33284# or ##33284 then press the blue OK button. If asked
Select SYSTEM tab at the bottom of the screen. Scroll down to SELF for a password, it is usually 040793 or 000000. Choose DEBUG
TEST and select. Unmark all option boxes except GSM/GPRS and SCREEN. Signal strength is after RxPower. Press Clear or power off to
click START. When the phone displays GPRS CONNECT NOW? get out.
Select NO. The 8th line down displays Signal Strength. Click
REFRESH to update Signal. LG CDMA PHONES ONLY (Except SPRINT) VX/UX/AX Series
VX10, 520, VX2000, 3100, 3200, 3300, 4400, 4500, 4600, 4700, 5550,
HTC Wizard 8125, 2125 (AT&T/Cingular) 6000, 6100, 7000, 8000, 8300, VX-8500 Chocolate, VX-9900 enV, etc
Enter *#*#364#*#* and your phone will enter test mode. Signal strength Press Menu 0. Enter Service Code: 000000 (six zeros). Scroll to
follows RSSI. Number shown is not –dBm. Strong signal is 31 (approx FIELD TEST. Press SELECT. Scroll to SERVICE or SCREEN. Press
-50dBm), weak signal is 4 (approx -105dBm). The higher the number, SELECT. Signal strength is on the line that says RX Level. On some
the stronger the signal. Press END or DONE to exit. newer phones you need to make a phone call while in test mode to get
the numbers to update. To exit test mode press CLEAR, END or turn
HTC 8525, (AT&T/Cingular) the phone off and on. (Note: On some models you will need to take the
Enter *#*#364#*#* and your phone will enter test mode. Signal strength battery off and put it back on again.)
follows “RSSI 1” and displays –dBm. Press ok to exit.

877-594-5766 [email protected]
 What the numbers mean:

Signal strength is a number ranging from roughly -50 to -105 (your phone
may show as a positive number). Closer to zero means a better signal, i.e. -
CELLULAR PHONE FIELD TEST MODES 50 (roughly full signal) is better than -105 (roughly no signal.)

LG CDMA Alternate Test Mode for Newer 2007/2008 models LG VX-8600 (or for LG models that do not accept the MENU, 0
Press ##7764726xxxx then press SEND (xxxx= your model number.) command.)
Service Code, 000000 (six zeros). Scroll to FIELD TEST. Press Press ##77647268600, then press SEND (##PROGRAM8600 SEND).
SELECT. Scroll to SERVICE or SCREEN. Press SELECT. Signal Service Code: 000000 (six zeros). Scroll to FIELD TEST. Press
strength is on the line that says RX Level. On Some newer phones you SELECT. Scroll to SERVICE or SCREEN. Press SELECT. Signal
will want to make a phone call while in the test mode to get the strength is on the line that says RX Level. On Some newer phones you
numbers to update. To exit test mode push CLEAR, END or simply will want to make a phone call while in the test mode to get the
turn off the phone. (Note: On some models you will need to take the numbers to update. To exit test mode push CLEAR, END or simply
battery off and put it turn off the phone. (Note: On some models you will need to take
the battery off and put it back on again.)
LG CDMA Phones Sprint only: Press ##33284# or ##33284, then
press the blue OK button. If asked for a password, it is usually 040793 LG VX-8700
or 000000. Choose DEBUG SCREEN. Signal strength is after Rx Press ##77647268700, then press SEND (##PROGRAM8700 SEND).
Power. Please Note: Certain newer phones have a special service Service Code, 000000 (six zeros). Scroll to FIELD TEST. Press
code that you must get from Sprint. Press CLR to exit Test Mode or SELECT. Scroll to SERVICE or SCREEN. Press SELECT. Signal
power off. strength is on the line that says RX Level. On Some newer phones you
will want to make a phone call while in the test mode to get the
LG CG300, C1300, L1400, C2000 (GSM Phones) numbers to update. To exit test mode push CLEAR, END or simply
Enter 2945#*#. Choose “Eng Mode” (Option 4) Press OK. Then turn off the phone. (Note: On some models you will need to take the
choose “Cell Environ” (Option 1) Press OK. The Cell Environ screen battery off and put it back on again.)
will appear with some information about your tower. Signal strength for
the tower you are using is on the top left line and is displayed in 2 digit LG VX-9800 (Note: must be done with the keyboard open)
format that is not dBm (the higher the number the better). The lines Press MENU, 0. Enter Service Code, 000000 (six zeros). Scroll to
below are neighboring towers. The channel number which shows FIELD TEST. Press SELECT. Scroll to SERVICE or SCREEN. Press
frequency(i.e.G598) is also displayed on the same line. Press END to SELECT. Signal strength is on the line that says RX Level. On Some
Exit. newer phones you will want to make a phone call while in the test
mode to get the numbers to update. To exit test mode push CLEAR,
LG CU400, CU500, TU550 (GSM ) END or simply turn off the phone. (Note: On some models you will
Enter 277634#*#. Choose “Modem Setting” (option 5) Press OK. Then need to take the battery off and put it back on again.)
choose “Engineer Mode” (Option 3) Press OK. A yellow window will
appear with some information about your tower. Signal strength follows LG VX-9900 (Note: must be done with the keyboard open)
RSSI: If you arrow down four times (using the little telephone key) you Press ##77647269900 SEND. Enter Service Code, 000000 (six zeros).
will see another screen that will display the RSSI and the Band you are Scroll to FIELD TEST. Press SELECT. Scroll to SERVICE or
using (i.e. PCS_1900). Press END twice to Exit. SCREEN. Press SELECT. Signal strength is on the line that says RX
Level. On Some newer phones you will want to make a phone call
LG 510 while in the test mode to get the numbers to update. To exit test mode
Press MENU, 3, 0. Enter Service Code: 000000 (six zeros). Scroll to push CLEAR, END or simply turn off the phone. (Note: On some
TEST MODE and select. Scroll to READ RSSI and select. To exit test models you will need to take the battery off and put it back on again.)
mode, turn off phone.
LG VX-10000 (Note: must be done with the keyboard open)
LG Sprint Touchpoint 1100, 2100, 2200, 5250, 5350, 4NE1, 1010, Press ##776472610000 SEND (##PROGRAM10000 SEND) Enter
1200 Service Code, 000000 (six zeros). Scroll to FIELD TEST. Press
Press ##33284. Select SAVE and press OK. Select SERVICE SELECT. Scroll to SERVICE or SCREEN. Press SELECT. Signal
SCREEN and press OK. The signal strength is on the 9th line down (for strength is on the line that says RX Level. On Some newer phones you
example, Rx power: -XX). To exit press END. will want to make a phone call while in the test mode to get the
numbers to update. To exit test mode push CLEAR, END or simply
LG VX-5300 turn off the phone. (Note: On some models you will need to take the
Press MENU, 0. Enter Service Code, 000000 (six zeros). Scroll to battery off and put it back on again.)
FIELD TEST. Press SELECT. Scroll to SERVICE or SCREEN. Press
SELECT. Signal strength is on the line that says RX Level. On Some Motorola M800 Bag Phone, V60, 120, E310, C331, 343, 353 (most
newer phones you will want to make a phone call while in the test older Motorola non-GSM phones)
mode to get the numbers to update. To exit test mode push CLEAR, Quickly press MENU 073887*. SECURITY CODE= 000000 (six zeros)
END or simply turn off the phone. (Note: On some models you will or 123456. Press OK. Scroll to TEST MODE, SELECT or CHANGE.
need to take the battery off and put it back on again.) Scroll to ENABLED, SELECT. Signal strength is 3rd number down on
the left side of screen. To exit, quickly hit MENU, then the button
LG VX-8350 directly to the left of MENU.
Press ## 77647268350, then press SEND (##PROGRAM8350 SEND).
Service Code: 000000 (six zeros). Scroll to FIELD TEST. Press Motorola Droid
SELECT. Scroll to SCREEN. Press SELECT. Signal strength is on the Press *#*#4636#*#* quickly. This takes you to a menu. Select “Phone
line that says RX Level. On Some newer phones you will want to make info” Signal Strength is the 7th line down.
a phone call while in the test mode to get the numbers to update. To
exit test mode push CLEAR, END or simply turn off the phone. (Note:
On some models you will need to take the battery off and put it back on
again.)

877-594-5766 [email protected]
 What the numbers mean:

Signal strength is a number ranging from roughly -50 to -105 (your phone
may show as a positive number). Closer to zero means a better signal, i.e. -
CELLULAR PHONE FIELD TEST MODES 50 (roughly full signal) is better than -105 (roughly no signal.)

Newer Motorola CDMA phones (v262, v710, E815, V265, V3 RAZR, Motorola T720, T721, T730, T731
KRZR, etc) Follow the process for V60 phones. Turn off phone off, then back on.
Quickly press MENU 073887* (0SETUP*). For RAZR, KRZR use Press MENU and the button left of the MENU button in quick
#073887*. For V323, V325 use CLR 073887*. Default Security Code: succession. The signal strength is the 3rd number down on the left
000000 or 12345. Press OK or SELECT. From the menu, select TEST side.
MODE. From the next screen highlight ENABLED. Press OK or
SELECT. The phone will then return to TEST MODE MENU. Power Motorola W315
the phone off and then back on. The signal strength number will be on Quickly press Clear (C) 073887*. Security Code: 000000. Press OK.
the 3rd line down followed by the letters MN/A, H/A or HN/A. To exit, Select “TEST MODE” from the Programming Menu. Press CHANGE,
press MENU followed by the left soft key. This allows you to toggle in highlight “Enable” and press SELECT. The phone will return to the
and out. For RAZR, KRZR, V325, V323 press CLR and then the upper Programming Menu. Pres END (Red Key). Test mode will appear
left soft key. For newer models such as the E815 and RAZR it may be automatically. Signal strength is the first set of numbers on the 3rd line
necessary to dial a fake phone number to get the signal reading to down. To exit, follow the procedure above but choose “Disable” instead
update. of “Enable”.

Motorola KRZR K1 (GSM) Nextel, Mike, SouthernLINC (Motorola iDEN Phones)

Press CLR 073887* very quickly. Security Code 000000. Highlight Quickly dial # , * , Menu, RIGHT ARROW. Scroll down to System
"Test Mode" and press OK. Highlight "Enabled" and press OK. The Status or RX Status, press “View.” NOTE: On some phones you will
phone will return to the menu. Power the phone off and on again. push TRACE or MENU so the signal will automatically update. Other
Phone will show signal strength on the second line down, last number phones you will have to press BACK to return to the Menu and then
(Example 67-061B. -061 is the signal strength). To toggle in and out: choose RX Status again to manually update. Turn the phone off to
Press # and then the upper left key with the dot on it. To Exit: Follow exit.
above instructions and choose "Disabled."
On the RX STATUS Screen the top decimal number is your Signal
Please Note: If "Browser Setup" is the only option in the menu, then Quality Equivalent (SQE). This number needs to be as high as
test mode is not available on your phone. possible between 25.00 to 35.00. Your signal strength is the second
number on the second or third line down. An example would be -00dB
Motorola C290 (Sprint) -90 where -90 is your signal strength.
Enter ##33284##. Enter Field Service Code, 040793 and press OK.
Signal strength is 3rd line down in from of MN/A or HN/A. Turn phone Nextel i710, i730, i733, i736, i830, i836
off and on to exit. Same as above to get into test mode. Press MENU to update signal
strength.
Motorola Q (Verizon)
Enter ##*, then press SEND. Highlight CALL STATUS SCREEN and Nextel i830
press Ok. Signal strength is the first number on the 3rd line down. Note: Follow the standard #, *, MENU, RIGHT ARROW. Select RX STATUS.
this screen also shows EVDO data readings. Press OK and then EXIT This phone does not automatically update so you will need to back out
to exit. to the menu and go back into RX STATUS to update the screen.

Motorola Q (Sprint) Nextel i1000, i2000

In phone mode, enter ##33284#. Highlight CALL STATUS SCREEN Quickly dial #, *, MENU, RIGHT ARROW. Scroll right 6 times to find
and press Ok. Choose EXIT option to exit. signal strength screen. Press TRACE to update.

Motorola V551, V555, V557 (GSM) Nextel (Sprint) IC402, IC502 IC902
Press Menu 073887* VERY QUICKLY. Security code 000000. Enter ##33284#. Field Service Code 040793 Press OK
Highlight “Test Mode” and press OK. Highlight “Enabled” and press Signal Strength is third line down, first set of numbers (i.e. 84HN/A is a
OK. The phone will return to the menu. Power the phone off and on. -84 dBm) To exit turn phone off.
Phone will show signal strength on the second line down, last number.
For example, 67-061B indicates a -061dBm received signal strength. Nokia 12xx, 51xx (except 5125), 61xx, 62xx, 71xx, 3285, 63xx, etc.
To toggle display on/off press Menu and then the left softkey. To Exit (Older TDMA/CDMA phones – does not work on newer GSM
follow instructions above but chose “Disabled.” Note: If “Browser phones)
Setup” is the only option in the menu then test mode is not available on Press *3001#12345#. Scroll up 1 to FIELD TEST (some phones may
your phone. say NET MONITOR instead of FIELD TEST) and SELECT. Scroll to
ENABLED and press OK. Turn phone off and then back on. Signal
Motorola StarTac strength is the upper or lower left number. After test mode is enabled it
Press FCN00** very quickly. Continue to press 83786633 and the will stay in your regular menu. To easily get in or out, press MENU, up
STO button. The phone should display US. (If not, the FCN00** 1 FIELD TEST and SELECT or OK. Dial 00 to get out and 01 to get
wasn’t done fast enough). Press 45# to display the signal strength. back in.
This number is not actually a dB reading, but is referencing the dB
strength. 45# should be pressed every time you wish to see the Nokia 2100
updated signal reading. The signal strength is between 65 and 150. Press *3001#12345#, MENU, then follow the above instructions.
Signal is the best at 150. To exit test mode, press 01#.

877-594-5766 [email protected]
 What the numbers mean:

Signal strength is a number ranging from roughly -50 to -105 (your phone
may show as a positive number). Closer to zero means a better signal, i.e. -
CELLULAR PHONE FIELD TEST MODES 50 (roughly full signal) is better than -105 (roughly no signal.)

Nokia 3285, 3360, 6360, (except 3590) Samsung A530, N330

Go through above process. After test mode is enable it will stay in Press MENU, 9, *. Enter Field Service Code, 000000 (six zeroes).
your regular menu. To easily get in or out, press MENU, up 1 to FIELD Select DEBUG SCREEN. Signal strengthis on the line that says T-63
TEST and SELECT. Dial 2100 to get out and 2101 to get back in (or D089 (for example, D089 is -89dBm). To exit, turn power off.
possible 0000 to get out and 2100 to get in).
Samsung A620, A660, A860, M300
Nokia 6215i, 6315 Enter ## 33284 and press OK. Enter security code 040793. Select
Press ##2773 then press END. Enter 000000 (six zeroes) for the User DEBUG SCREEN and press OK. Signal strength is 2nd number on 2nd
Lock Code. Signal strength follows RX Level or RX Power. Press END line. (For example, T-XX Do XX-05). To exit, turn off phone.
to exit.
Samsung A640
Nokia 6255, 6256 and newer CDMA Nokia phones Enter ##33284#. The phone asks for a 6 digit security code which you
Follow the regular Nokia instructions above (*3001#12345#, etc). will need to get from Sprint. After entering it the phone will go into the
When you power the phone back on, select NET MONITOR from the test mode screen. Your signal strength is on the line that says T-
menu and enter 3202 in the entryfield and press OK to get to the test xxD0xx. To exit, turn off phone.
mode screen. It will show 32-02 in the upper corner of the display.
Signal strength is the left negative number. Go back to NET MONITOR Samsung A630, A650, N330
and enter 0000 to get out. (Sprint Nokia phones: ##33284#.) Press MENU, 9, *. Enter Field Service code: 000000 (six zeros).
Select DEBUG SCREEN, press OK. Signal strength is on the 5th line,
Nokia 6305i 2nd number (T-65 DO 87-06). The number omits the negative. To exit,
Press Menu (OK), 0. Service Code 000000. Press OK. Choose turn off phone.
DEBUG SCREEN. Press OK. Signal Strength is after RX= or RSSI=.
This screen also shows EVDO RSSI. To exit, power phone off. Samsung A670, A570
Press MENU, 7, *. Enter Service Code: 000000 (six zeros). Select
Palm Treo 600, 650, 700p, 700w(x) DEBUG SCREEN. Signal strength is on the 1st line. To exit, turn off
Sprint: Press ##33284 and DIAL. The signal strength (RSSI phone.
Value) is on the first line. To exit, press CANCEL.
Samsung SYNC A707, A717, A727
Verizon: Press #*#33284 AND dial. The signal strength Press *#0011#. The phone will enter Test mode. Signal Strength
(RSSI Value) is on the first line. To exit, press CANCEL. follows P: (i.e. P:-73). This screen will also show the frequency being
used (i.e. GSM 1900). The screen will automatically update itself. To
Cingular: Press #*744625. The signal strength (RSSI Value) exit press the END key.
is on the first line. To exit, press CANCEL.
Samsung A560, A740, A760, A840, A880, P207
Panasonic – Duramax, TX310, TX320 Enter ## 33284#, press OK. Enter security code 040793. Select
Press #7764726#. Press SEND. Scroll down to where it says NAM 1 DEBUG SCREEN and press OK. Signal strength is 2nd number on 2nd
and press OK. Scroll to ENTER LEVEL 4. Press YES. Scroll to line (for example, T-XX Do XX -05). To exit, turn off phone.
BUILT IN MONITOR. Press EDIT, CLEAR, 1, OK. Press BACK,
BACK TO LEVEL 1, YES, EXIT, SAVE CHANGES, YES. Signal Samsung A790
strength is the top right number. To get out of test mode, follow the Enter ##33284#. Enter Service Code, 040793. Signal strength is after
same sequence: EDIT, CLEAR, 0, OK. the D. To exit, turn phone off.

Pantech (CDMA Phones Only) PN-210, PN-215, PN-218 Samsung A740, A850, A930, A950 U740 A870 (Verizon)
Press ##2773. Press END key. Enter 000000 (six zeros) for the Press MENU (blue center button). Scroll to SETTINGS & TOOLS
security code. Hit OK. Signal strength follows RX level or RX power. (tools icon) then press the # key. Enter User Lock Code, 000000 (six
zeroes). Select DEBUG SCREEN. The screen will read some similar to
Pantech PN-3200 T-63 D089. The number after the D is the signal strength, for example -
Press ##27732726, press END key. Scroll down and select DEBUG. 89dBm. To exit, turn power off.
The signal strength is the 4th line down. (For example Rx-96)
Samsung A900, A920 and A570
Samsung A310 Enter ##33284# or ##33284 and press the blue OK button. Enter Field
Press MENU, 0, *. Then enter code 000000 (six zeros). Choose Service Code 040793 or 000000 (six zeroes). Choose DEBUG
DEBUG, 4th line, last number. SCREEN or FIELD TEST and then SCREEN. Signal strength is the
number after the D. (Note: the A900 appears to go right into the test
Samsung A460, 3500, A540 screen after the 040793 is entered.)
Press MENU, 9, 0. Enter Lock Code: 040793. Select DEBUG
SCREEN and press OK. Signal strength is the 2nd number on the 2nd Samsung E105, D807, A517, E316, E317, X426, X427, X475, S300,
line down. To exit test mode, turn off phone. S307, D347 (GSM)
Enter *#9324#. Signal strength is last number on the 4th line. The
Samsung A500, N400 number omits the negative. To exit, turn off phone.
Press MENU 010. Enter 040793. Select DEBUG SCREEN. Signal
strength is the 2nd number on the 2nd line down. To exit test mode, turn Cingular (Samsung) BlackJack
off phone. At the home screen, type in *#0011# and the information will pop up
(do not hit ok or anything else after entering key sequence.)

877-594-5766 [email protected]
 What the numbers mean:

Signal strength is a number ranging from roughly -50 to -105 (your phone
may show as a positive number). Closer to zero means a better signal, i.e. -
CELLULAR PHONE FIELD TEST MODES 50 (roughly full signal) is better than -105 (roughly no signal.)

Siemens S46 (TDMA)

Samsung BlackJack SGH-I607, A412 , Black Jack II Press MENU, select MONITOR, RSSI, -XX. Test mode also tells
Option 1: On the main screen press *#0011# and an information screen will frequency. To exit, press the power button as the back button. To
appear. force TDMA, press MENU. Scroll to NETWORK. Scroll to USER
Option 2: In the Windows folder open the folder called “Test Mode” and SETTING. Scroll to TDMA ONLY and press OK.
run the file by the same name. Signal strength will follow RSSI. This
screen will also show the frequency which you are operating on. Sprint PPC 6700
Simply select EXIT to get out of this screen. Run application FieldTrial.exe located in WINDOWS folder.
Samsung i730, I760 (Verizon)
In phone mode, enter **33284 and the Security Code 000000 (six Sprint Franklin CDU-550, Novatel U720
zeroes). Choose MONITOR. The receive signal strength follows R- on On the Sprint Software: Click Menu, Click Device Info & Diagnostics,
the screen, transmission signal strength follows T-. Signal strength is on the line that says “Communication Mode” or
“Signal Strength.”
Samsung N240
Enter ##33284 and press OK. Select DEBUG SCREEN and press T-Mobile DASH, HTC EXCALIBER, S620
OK. Signal strength is 2nd number on 2nd line (for example, T-XX Do Enter *#*#364#*#* and your phone will enter test mode. Signal strength
XX-05). To exit, turn off phone. follows RSSI. This test mode does not show –dB. Strong signal is 31
(approximately -50dBm), weak signal is 4 (approximately -105dBm).
Samsung U520. U340 The higher the number (31 vs 4) the better the signal. Press END or
Press MENU (OK Button) , 9, 0. User Lock Code: 000000 (six zeros). Done to exit.
Choose DEBUG. Signal strength is 2nd number on 2nd line (for
example, T-63 D085-5. This means -085 dBm).To exit, turn off phone. VERIZON Access Manager
Once connected place your mouse cursor over the bottom signal
Samsung U540 reading (bars). A little window will pop up with a signal strength in –
Press MENU, choose “Phone Settings” and press #. User Lock Code: dBm.
000000 (six zeros). Choose Field Test Mode and then DEBUG. Signal
strength is on the line that says: T-XX DXXX. To exit, turn off phone. Option GT Max
Signal Strength is below the bars on the main screen.
Sanyo 4500 (not VM4500), 4700
Scroll down to DISPLAY and press OK. Press 0 (zero). Will ask for
Service Code – enter 040793. Select SCREEN and press OK. Signal If you do not see your phone model listed:
strength is the negative number at the bottom (for example (-97). To
exit test mode, turn off phone. • Try using the field test mode for other phones from the same
manufacturer.
Sanyo 4900, 5150, 5300, 6200, 6400, 8100 • Not all phones have a user accessible field test mode. In
Press ##040793 MENU. Scroll to SAVE PHONE# and press OK. particular, many GSM phones.
Select SCREEN and press OK. Signal strength is the 4th line down (for • Some carriers lock out/remove field test mode.
example, Rxlev: -XX.Xdb). Press and hold the top right or left button to
• If the code for your phone is not listed then we do not know
keep the field test screen from flashing. To exit, turn off phone.
what it is.
Sanyo 5400, 7300, RL2500, RL7300
If you know the code for a phone not listed please contact us at
Press ##040793, MENU and then select SCREEN. You may havt to
[email protected]
press the up arrow to keep from flashing in and out. (With 7300 you
may need to make a call to keep from flashing in and out. Any fake
What the numbers mean:
number works fine).
Signal strength is a number ranging from roughly -50 to -105 (your
Sanyo Katana
phone may show as a positive number).
US Model: Enter ##33284# and select SCREEN. Dial a fake phone
number (i.e 555-555-5555)to get the phone to update. Signal strength
Closer to zero means a better signal, i.e. -50 is better than -100.
is on the line that says RX Level. Canadian Model: Enter ##786# and
press OK.
About us:
Sanyo PM-8200
##33284 OK
wpsantennas.com is one of the largest cellular antenna, amplifier and
repeater providers in the US offering quality products from Wilson
Sanyo RL-4920, RL-4930, MM7400, SCP-3100, SCP-7000 or Newer
Cellular, Digital Antenna, Antenex, Centurion, Laird Technologies,
Sanyo phones not listed above
ARC Wireless, Wireless Extenders (zBoost) and more. Please visit us
Press ##786#. Select OK. Select SERVICE SCREEN and press OK.
on the web at http://www.wpsantennas.com
Two lines of information will be displayed. Dial a fake phone number
(ie: 555-555-5555) and press SEND. Signal strength follows RxLev on
the 4th line. Turn off phone to exit field test mode.

877-594-5766 [email protected]