Scribd
Upload
68 views3 pages

2 Marks QP

The document contains 50 questions across 5 units related to microprocessors and microcontrollers. The questions cover topics such as addressing modes of 8086, interrupt types, register definitions, bus structures, timer/counter applications, serial communication protocols, 8051 architecture including ports, registers and programming. Students are required to answer all questions which are worth 100 marks total.

Uploaded by

Suguna Priya
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
68 views3 pages

2 Marks QP

The document contains 50 questions across 5 units related to microprocessors and microcontrollers. The questions cover topics such as addressing modes of 8086, interrupt types, register definitions, bus structures, timer/counter applications, serial communication protocols, 8051 architecture including ports, registers and programming. Students are required to answer all questions which are worth 100 marks total.

Uploaded by

Suguna Priya
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 3

SRI RAMANUJAR ENGINEERING COLLEGE

DEPARTMENT OF CSE and IT

EC8691- MICROPROCESSORS AND MICROCONTROLLERS

DATE: .10.19 MARKS: 100

Answer All the Questions (2x50=100)

UNIT 1

1. List the addressing modes of 8086. Give examples.

2. Write about need of interrupt (ref 5.1) and list different types of interrupt supported in 8086.

3. Give the flag register of 8086.

4. Define Stack pointer (Q 29, chapter 1) and stack register

5. List the segment register of 8086.

6. The offset address of a data is 341B H and the data segment register vale is (123A)H. What is the physical
address of the data.

7. List the modes of operation in 8086.

8. Define Macros.

9. What are byte and string manipulation.

10. Give the difference between align and assume.

UNIT 2

11. Define Bus (Q. 14, chapter 6) and System Bus.

12. When is coprocessor used?

13. What is the need of LOCK signal?

14. What is meant by multi programming?

15. Write some examples for advanced microprocessor.

16. Define Machine Cycle.

17. Differentiate External and internal bus.

18. Compare closely and loosely coupled Configuration.

19. Show how synchronization is made between 8086 and its coprocessor.
20. Draw the read cycle timing diagram of minimum mode.

Unit 3

21. Draw the block diagram of alarm controller with 8086 processor.

22. Give the various modes and applications of 8254 timer.

23. List the operationg modes of 8255A and 8237 A

24. What frequency transmit clock is required by an 8251 in order for it to transmit data at 4800 baud with a
bad rate factor of 16.

25. Give the control word and status word format of 8251.

26. Discuss the salient feature of 8259

27. How DMA is initiated.

28. Differentiate Memory mapped and I/o mapped I/o.

29. Give the read back command of 8254 timer.

30. Genarate a square wave using DAC.

UNIT 4

31. Give the PSW register of 8051.

32. Define DPTR and Program counter of 8051.

33. Give the multi fnction port of 8051 microcontroller.

34. What happens in powerdown mode of 8051.

35. Give the difference between RET and RETI instruction in 8051.

36. What are the different types of operand addressing mode in 8051.

37. Give the format of TMOD and TCON register of timer in 8051 and give the difference between timer and
counter.

38. Assume that XTAL=11.0592MHz. Write a program togenarate a square wave of 2KHz frequency on pin
P1.5.

39. Give the bit pattern of SCON and PCON register of 8051 serial port.

40. Give the Vector address and priority sequence of the interrupt of 8051.

UNIT 5

41. Give the pin description of LCD module and interfacing of LCD module with 8051.
42. What is meant by scan and return line (18.2.2) and draw the matrix keyboard connection.

43. Write an AlP for AD conversion using 8051 with its interfacing diagram.

44. What is meant by signal conditioning?

45. Mention the features of serial port in mode 0.

46. Mention number of register bank and their address in 8051.

47. What are the types of sensors used for interfacing?

48. What are the types of ADC?

49. State how bad rate is calculated for serial data transfer in mode 1.

50. What is the significance of EA and PSEN pin?

You might also like