INTERNATIONAL ASSOCIATION OF CLASSIFICATION SOCIETIES

Requirements
concerning
LOAD LINE

IACS Req. 2011

 Contents, Page 1

CONTENTS

L1 Deleted

L2 Intact stability - Matter of class 1988/Rev. 1 June 2000

L3 Deleted May 2001

L4 Closure of Chain Lockers Rev.3_Corr.1 Aug 2011

L5 Onboard Computer for Stability Calculations Corr.1 Nov 2006

See also Recommendation No. 2

IACS Req. 1996/Rev. 2011

 L1–L2

L1 Deleted

▲
▲
L2 Intact stability - matter of class
(1988)
(Rev.1
June All new ships with a length of 24 m and above will be assigned class only after it has been demonstrated
2000) that their intact stability is adequate for the service intended.

Adequate intact stability means compliance with standards laid down by the relevant Administration or
those of the Classification Society taking into account the ship’s size and type. The level of intact
stability for ships of all sizes in any case should not be less than that provided by IMO Resolution
A.749(18), chapters 3.1, 3.2 and 4.1 as amended by MSC Resolution 75(69).

Evidence of approval by the Administration concerned may be accepted for the purpose of classification.

▲
▲

IACS Req. 1988/Rev.1 2000

 L3

L3 Intact stability of tankers during

liquid transfer operations
Re-categorized as Recommendation No. 60 in May 2001.

▲
▲
 L4

L4
S18 Closure of Chain Lockers
(Nov
(cont)
2002) This Unified Requirement is applicable to ships with a length of 24 m and above built in
(Rev.1 accordance with the 1966 Load Line Convention or the 1988 Protocol to the Load Line
July Convention and the keels of which are laid or which are at a similar stage of construction on
2003) or after 1 July 2003.
(Rev.2
Nov 1. Spurling pipes and cable lockers are to be watertight up to the weather deck.
2005) Bulkheads between separate cable lockers (see Arrangement 1), or which form a common
(Rev.3 boundary of cable lockers (see Arrangement 2), need not however be watertight.
Mar
2011) 2. Where means of access is provided, it is to be closed by a substantial cover and
(Corr.1 secured by closely spaced bolts.
Aug
2011) 3. Where a means of access to spurling pipes or cable lockers is located below the
weather deck, the access cover and its securing arrangements are to be in accordance with
recognized standards* or equivalent for watertight manhole covers. Butterfly nuts and/or
hinged bolts are prohibited as the securing mechanism for the access cover.

4. Spurling pipes through which anchor cables are led are to be provided with
permanently attached closing appliances** to minimize water ingress.

* Examples of the recognized standards are such as:

i) ISO 5894-1999
ii) China: GB 11628-1989 Ship Manhole Cover
iii) India: IS 15876-2009 "Ships and Marine Technology manholes with bolted covers"
iv) Japan: JIS F2304, "Ship's Manholes" and JIS F2329, "Marine Small Size Manhole"
v) Korea: KSV 2339:2006 and KS VISO5894
vi) Norway: NS 6260:1985 to NS 6266:1985
vii) Russia: GOST 2021-90 "Ship's steel manholes. Specifications"

** Examples of acceptable arrangements are such as:

i) steel plates with cutouts to accomodate chain links or
ii) canvas hoods with a lashing arrangement that maintains the cover in the secured position.

Notes:

1. Changes introduced in Rev.3 of this UR are to be uniformly implemented by IACS Societies on

ships contracted for construction on or after 1 January 2012.

2. The “contracted for construction” date means the date on which the contract to build the vessel
is signed between the prospective owner and the shipbuilder. For further details regarding the date of
“contract for construction”, refer to IACS Procedural Requirement (PR) No. 29.
End of
Document

Page 1 of 1 IACS Req.

IACS2002/Rev.3_Corr.1 2011
Req. 2002/Rev.3 2011
 L5

L5
L5 Onboard Computers for Stability
(May 04)
(cont’d)
(Rev.1 Calculations
Feb.
2005) Application
(Rev.2
Sept The use of onboard computers for stability calculations is not a requirement of class.
2006)
(Corr.1 However, a stability software installed onboard shall cover all stability requirements
Nov applicable to the ship. This UR, which requires only software approval, applies to onboard
2006) computers which are provided with software capable of performing stability calculations for
the vessel.

Active and passive systems are defined in paragraph 2. This UR covers passive systems and
the off-line operation mode of active systems only.

The requirements in this UR apply to stability software on ships contracted for construction on
or after 1 July 2005.

1. General

- The scope of a stability calculation software shall be in accordance with the

stability information as approved by the administration and shall at least include
all information and perform all calculations or checks as necessary to ensure
compliance with the applicable stability requirements.

- Approved stability software is not a substitute for the approved stability

information, and is used as a supplement to the approved stability information to
facilitate stability calculations.

- The input/output information should be easily comparable with approved stability

information so as to avoid confusion and possible misinterpretation by the
operator relative to the approved stability information.

- An operation manual is to be provided for the onboard computer stability

software.

- The language in which the stability information is displayed and printed out as
well as the operation manual is written should be the same as used in the ship’s
approved stability information. The society may require a translation into a
language considered appropriate.

Note:
1. The “contracted for construction” date means the date on which the contract to build
the vessel is signed between the prospective owner and the shipbuilder. For
further details regarding the date of “contracted for construction”, refer to IACS Procedural
Requirement (PR) No.29.

2. Changes introduced in Rev.2 of this UR are to be uniformly applied by IACS Societies on

ships contracted for construction on or after 1 January 2007.

Page 1 of 9 IACS Req.IACS Req. 2004/Rev.2

2004/Rev.2 2006/Corr.12006
2006
 L5

- The onboard computer software for stability calculations is ship specific and
L5 the results of the calculations are only applicable to the ship for which it has been
(cont’d) approved.

- In case of modifications implying changes in the main data or internal

arrangement of the ship, the specific approval of any original stability calculation
software is no longer valid. The software is to be modified accordingly and re-
approved.

2. Calculation Systems

A passive system requires manual data entry,

an active system replaces the manual entry with sensors reading and entering the contents of
tanks, etc., and

a third system, an integrated system, controls or initiates actions based on the sensor-
supplied inputs and is not within the scope of this UR.

3. Types of Stability Software

Three types of calculations performed by stability software are acceptable depending upon a
vessel’s stability requirements:

Type 1

Software calculating intact stability only (for vessels not required to meet a damage stability
criterion)

Type 2

Software calculating intact stability and checking damage stability on basis of a limit curve
(e.g. for vessels applicable to SOLAS Part B-1 damage stability calculations, etc.) or
previously approved loading conditions and

Type 3

Software calculating intact stability and damage stability by direct application of pre-
programmed damage cases for each loading condition (for some tankers etc.)

Page 2 of 9 IACS Req. 2004/Rev.2 2006

 L5

4. Functional requirements:
L5
(cont’d) 4.1 The calculation program shall present relevant parameters of each loading
condition in order to assist the Master in his judgement on whether the ship is
loaded within the approval limits. The following parameters shall be presented for
a given loading condition:

- deadweight data;

- lightship data;

- trim;

- draft at the draft marks and perpendiculars;

- summary of loading condition displacement, VCG, LCG and, if applicable, TCG;

- downflooding angle and corresponding downflooding opening;

- compliance with stability criteria: Listing of all calculated stability criteria, the limit
values, the obtained values and the conclusions (criteria fulfilled or not fulfilled).

4.2 If direct damage stability calculations are performed, the relevant damage cases
according to the applicable rules shall be pre-defined for automatic check of a
given loading condition.

4.3 A clear warning shall be given on screen and in hard copy printout if any of the
loading limitations are not complied with.

4.4 The data are to be presented on screen and in hard copy printout in a clear
unambiguous manner.

4.5 The date and time of a saved calculation shall be part of the screen
display and hard copy printout.

4.6 Each hard copy printout shall contain identification of the calculation
program including version number.

4.7 Units of measurement are to be clearly identified and used consistently

within a loading calculation.

Page 3 of 9 IACS Req. 2004/Rev.2 2006

 L5

5. Acceptable Tolerances
L5
(cont’d) Depending on the type and scope of programs, the acceptable tolerances are to be
determined differently, according to 5.1 or 5.2. Deviation from these tolerances shall not be
accepted unless the Society considers that there is a satisfactory explanation for the
difference and that there will be no adverse effect on the safety of the ship.

Examples of pre-programmed input data include the following:

Hydrostatic data: Displacement, LCB, LCF, VCB, KMt and MCT versus draught.

Stability data: KN or MS values at appropriate heel/ trim angles versus

displacement, stability limits.

Compartment data: Volume, LCG, VCG, TCG and FSM/ Grain heeling
moments vs level of the compartment’s contents.

Examples of output data include the following:

Hydrostatic data: Displacement, LCB, LCF, VCB, KMt and MCT versus
draught as well as actual draughts, trim.

Stability data: FSC (free surface correction), GZ-values, KG, GM, KG/GM
limits, allowable grain heeling moments, derived stability
criteria, e.g. areas under the GZ curve, weather criteria.

Compartment data: Calculated Volume, LCG, VCG, TCG and FSM/ Grain
heeling moments vs level of the compartment’s contents.

The computational accuracy of the calculation program results shall be within the acceptable
tolerances specified in 5.1 or 5.2, of the results using an independent program or the
approved stability information with identical input.

5.1 Programs which use only pre-programmed data from the approved stability
information as the basis for stability calculations, shall have zero tolerances for
the printouts of input data.

Output data tolerances are to be close to zero, however, small differences

associated with calculation rounding or abridged input data are acceptable.
Additionally differences associated with the use of hydrostatic and stability data
for trims that differ from those in the approved stability information, are
acceptable subject to review by the individual Society.

5.2 Programs which use hull form models as their basis for stability calculations,
shall have tolerances for the printouts of basic calculated data established
against either data from the approved stability information or data obtained using the
approval authority’s model. Acceptable tolerances shall be in accordance
with Table 1.

Page 4 of 9 IACS Req. 2004/Rev.2 2006

 L5

L5 Table 1
(cont’d)

Hull Form Dependent

Displacement 2%
Longitudinal center of buoyancy, from AP 1% / 50 cm max
Vertical center of buoyancy 1% / 5 cm max
Transverse center of buoyancy 0.5% of B / 5 cm max
Longitudinal center of flotation, from AP 1% / 50 cm max
Moment to trim 1 cm 2%
Transverse metacentric height 1% / 5 cm max
Longitudinal metacentric height 1% / 50 cm max
Cross curves of stability 5 cm

Compartment dependent

Volume or deadweight 2%
Longitudinal center of gravity, from AP 1% / 50 cm max
Vertical centre of gravity 1% / 5 cm max
Transverse center of gravity 0.5% of B / 5 cm max
Free surface moment 2%
Shifting moment 5%
Level of contents 2%

Trim and stability

Draughts (forward, aft, mean) 1% / 5 cm max

GMt 1% / 5 cm max
GZ values 5% / 5 cm max
FS correction 2%
Downflooding angle 20
Equilibrium angles 10
Distance to unprotected openings or +/- 5% / 5 cm max
margin line from WL, if applicable
Areas under righting arm curve 5% or 0,0012mrad

Deviation in % = {(base value-applicant’s value)/base value} *100

Where the “base value” may be from the approved stability information or
the society’s computer model.

Page 5 of 9 IACS Req. 2004/Rev.2 2006

 L5

6. Approval Procedure
L5
(cont’d)
Conditions of approval of the onboard software for stability calculations

The onboard software used for stability calculations is subject to approval, which is to include;

- verification of type approval, if any;

- verification that the data used is consistent with the current condition of the ship.
(Refer to paragraph 6.2);

- verification and approval of the test conditions;

- verification that the software is appropriate for the type of ship and stability
calculations required.

The satisfactory operation of the software with the onboard computer(s) for stability
calculations is to be verified by testing upon installation. (Refer to paragraph 8). A copy of the
approved test conditions and the operation manual for the computer/ software are to be
available on board.

6.1 General Approval (optional):

Upon application to the Society for general approval of the calculation program, the Society
may provide the applicant with test data consisting of two or more design data sets, each of
which is to include a ship’s hull form data, compartmentation data, lightship characteristics
and deadweight data, in sufficient detail to accurately define the ship and it’s loading
condition. Acceptable hull form and compartmentation data may be in the form of surface
coordinates for modeling the hull form and compartment boundaries, e.g: a table of offsets, or
in the form of pre-calculated tabular data, e.g: hydrostatic tables, capacity tables, etc.,
depending upon the form of data used by the software being submitted for approval.
Alternatively, the general approval may be given based on at least two test ships agreed
upon between the society and the applicant.

In general, the software is to be tested for two types of ships for which approval is requested,
with at least one design data set for each of the two types. Where approval is requested for
only one type of ship, a minimum of two data sets for different hull forms of that type of ship
are required to be tested. For calculation software which is bases on the input of hull form
data, design data sets shall be provided for three types of ships for which the software is to
be approved, or a minimum of three data sets for different hull forms if approval is requested
for only one type of ship. Representative ship types which require different design data sets
due to their hull forms, typical arrangements, and nature of cargo include: tanker, bulk carrier,
container ship, and other dry cargo and passenger ships. The test data sets shall be used by
the applicant to run the calculation program for the test ships. The results obtained (together
with the hydrostatic data and cross-curve data developed by the program, if appropriate) shall
be submitted to the Society for the assessment of the program’s computational accuracy. The
Society shall perform parallel calculations using the same data sets and a comparison of
these results will be made against the applicant’s submitted program’s results.

Page 6 of 9 IACS Req. 2004/Rev.2 2006

 L5

6.2 Specific Approval:

L5
(cont’d) - The Society shall verify the accuracy of the computational results and actual ship data
used by the calculation program for the particular ship on which the
program will be installed.

- Upon application to the Society for data verification, the Society and the
applicant shall agree on a minimum of four loading conditions, taken from the
ship’s approved stability information, which are to be used as the test conditions. For
ships carrying liquids in bulk, at least one of the conditions shall include
partially filled tanks. For ships carrying grain in bulk, one of the grain loading
conditions shall include a partially filled grain compartment. Within the test
conditions each compartment shall be loaded at least once. The test
conditions normally are to cover the range of load draughts from the
deepest envisaged loaded condition to the light ballast condition and shall
include at least one departure and one arrival condition.

- The Society is to verify that the following data, submitted by the applicant, is
consistent with arrangements and most recently approved lightship
characteristics of the ship according to current plans and documentation on file
with the Society, subject to possible further verification on board:

- Identification of the calculation program including version number.

- Main dimensions, hydrostatic particulars and, if applicable, the ship profile.

- The position of the forward and after perpendiculars, and if appropriate, the
calculation method to derive the forward and after draughts at the actual position
of the ship’s draught marks.

- Ship lightweight and centre of gravity derived from the most recently approved
inclining experiment or light weight check.

- Lines plan, offset tables or other suitable presentation of hull form data if
necessary for the Society to model the ship.

- Compartment definitions, including frame spacing, and centres of volume,

together with capacity tables (sounding/ullage tables), free surface corrections, if
appropriate.

- Cargo and Consumables distribution for each loading condition.

Verification by the Society does not absolve the applicant and shipowner of responsibility for
ensuring that the information programmed into the onboard computer software is consistent
with the current condition of the ship.

Page 7 of 9 IACS Req. 2004/Rev.2 2006

 L5

7. Operation Manual
L5
(cont’d) A simple and straightforward operation manual is to be provided, containing descriptions and
instructions, as appropriate, for at least the following:

- installation

- function keys

- menu displays

- input and output data

- required minimum hardware to operate the software

- use of the test loading conditions

- computer-guided dialogue steps

- list of warnings

8. Installation Testing

To ensure correct working of the computer after the final or updated software has been
installed, it is the responsibility of the ship’s Master to have test calculations carried out
according to the following pattern in the presence of a Society surveyor:

From the approved test conditions at least one load case (other than light ship) shall be
calculated. Note: Actual loading condition results are not suitable for checking the correct
working of the computer.

Normally, the test conditions are permanently stored in the computer.

Steps to be performed:

- Retrieve the test load case and start a calculation run; compare the
stability results with those in the documentation.

- Change several items of deadweight (tank weights and the cargo weight)
sufficiently to change the draught or displacement by at least 10%. The
results are to be reviewed to ensure that they differ in a logical way from
those of the approved test condition.

- Revise the above modified load condition to restore the initial test
condition and compare the results. The relevant input and output data of the
approved test condition are to been replicated.

- Alternatively, one or more test conditions shall be selected and the test
calculation performed by entering all deadweight data for each selected test
condition into the program as if it were a proposed loading. The
results shall be verified as identical to the results in the approved copy of
the test conditions.

Page 8 of 9 IACS Req. 2004/Rev.2 2006

 L5

9. Periodical Testing
L5
(cont’d) It is the responsibility of the ship’s master to check the accuracy of the onboard computer for
stability calculations at each Annual Survey by applying at least one approved test condition.
If a Society surveyor is not present for the computer check, a copy of the test condition
results obtained by the computer check is to be retained on board as documentation of
satisfactory testing for the surveyor’s verification.

At each Special Survey this checking for all approved test loading conditions is to be done in
presence of the surveyor.

The testing procedure shall be carried out in accordance with paragraph 8.

10. Other Requirements

Protection against unintentional or unauthorised modification of programs and data shall be

provided.

The program shall monitor operation and activate an alarm when the program is incorrectly or
abnormally used.

The program and any data stored in the system shall be protected from corruption by loss of
power.

Error messages with regard to limitations such as filling a compartment beyond capacity, or
exceeding the assigned load line, etc. shall be included.

End of
Document

Page 9 of 9 IACS Req. 2004/Rev.2 2006