Performance Testing Procedure Rev 0 PDF
Performance Testing Procedure Rev 0 PDF
Performance Testing Procedure Rev 0 PDF
VENDOR DOCUMENTS
FOR
WELLHEAD CONTROL PANELS
PO No : A-84508-9787-4W-2200
TAG No : 32-QJP-001 & 32-QJP-101
Document No.
ID-F-NB-P-JP-002-H05-0001
TABLE OF CONTENTS
1 GENERAL 4
3 FUNCTIONAL TEST 5
4 CLEANLINESS TEST 8
1 GENERAL
3 FUNCTIONAL TEST
Pressurized the initial Pressure in Hydraulic Accumulator with Nitrogen gas (90% of
minimum operating pressure) and the results shall be recorded.
Required several preparation & check items to be done, before running the Wellhead
Control Panel as follows:
• Fill the hydraulic tank with “Tellus 32” until 75% of the full tank.
• Tighten all the tubing and pipe connection.
• Plug the output to all Wing Valve, SSV, and SCSSV bulkheads.
• Open all valve
• Close the ball valve in return line.
• Connect Pressure Transmitters to Junction Box.
• Connect SOV to Junction Box.
• Connect Push Button to Junction Box.
• Connect all Junction Box to PLC simulator.
• Install power and control cable to each motor.
• Show oil cleanliness to NAS 1638 class 6.
The Function test will be perform for each module of well and all part of instruments. For
the leak test will be perform and record. Duration for the leak test is 12 hours.
3.2.1 Start & Stop Motor Pump on Manual Condition (Without PLC Simulator)
The purposes of this test are to ensure Motor can be run by Local control station on
Wellhead Control Panel and to ensure a relief valves setting pressure are working
properly.
Without PLC simulator motor can be run until the pressure reach set point of relief valve
(3,300 psig for MP & 6,050 psig for HP), because if we used PLC simulator motor will be
stop at 3,000 psig (MP) & 5,500 psig (HP) according to set point of start & stop for motor.
The test result will be reported (Form 2 A).
3.2.2 Start & Stop Motor Pump on Remote Condition (With PLC Simulator)
The purposes of this test are to ensure the whole system will work properly after WHCP
are connected to PSD system. The PSD system represent by PLC Simulator.
For pressurize the system we sequence to start & stop the motor pump. Depend which
motor pump need to be used.
NORTH BELUT PROJECT
WHP EPC
PT. NISCONI PT. IBP
TITLE DOCUMENT NUMBER REV DATE PAGE
PERFORMACE TESTING AND
ID-F-NB-P-JP-002-H05-0001 0 26-Dec.-07 6 of 35
ACCEPTANCE TEST PROCEDURE
- Pump 30-QJP-001-2A
Working Step:
1. Open the line of pump 30-QJP-001-2A (AC-4, AC-5, AC-6, AC-8,CD-13)
2. Open isolation valve to accumulator CA5 & CA6, and close the return line
3. Start the motor and automatically stop when the pressure of the hydraulic
already reach 3000 Psig (Check on PI-1020A and PT-1014)
4. Check the running time duration of the motor to reach the desired operating
pressure.
5. If the pressure lines drop before 30 minutes, check the fitting and tubing
connections, which leakage may occur, repeat step 4 to 7.
- Pump 30-QJP-001-2B
Working Step:
1. Close valve AC-3
2. Open the return/bleed line of accumulator CA-5 & CA6
3. Check on PI-1020B, the pressure should back to initial pressure.
4. Close return/bleed line of accumulator CA-5 & CA-6
5. Close the line to Pump 30-QJP-001-2A (AC-4), open valve AC-3
6. Open the line of pump 30-QJP-001-2B (AC-9, AC-10, AC-11, CD-14)
7. Start the motor and automatically stop when the pressure of the hydraulic
already reaches 3000 Psig (Check on PI-1020B and PT-1014).
6. Check the running time duration of the motor to reach the desired operating
pressure.
- Pump 30-QJP-001-1A
Working Step:
1. Valve AC-2 open position
2. Open the line of pump 30-QJP-001-1A (AC-12, AC-13, AC-14, AC-16, CD-15)
3. Open isolation valve to accumulator CA-11 & CA-12, and close the return
line
4. Start the motor and automatically stop the motor if the pressure of the
hydraulic already reach 5500 Psig (Check on PI-1021A and PT-1015)
5. Check the running time duration of the motor to reach the desired operating
pressure.
6. While all motor in stop condition, wait for 30 minutes. If the line pressure keeps
in the working pressure, mean the Hydraulic Unit working properly.
7. If the pressure line drops before 30 minutes, check the fitting and tubing
connections, which leakage may occur, repeat step 4 to 7.
NORTH BELUT PROJECT
WHP EPC
PT. NISCONI PT. IBP
TITLE DOCUMENT NUMBER REV DATE PAGE
PERFORMACE TESTING AND
ID-F-NB-P-JP-002-H05-0001 0 26-Dec.-07 7 of 35
ACCEPTANCE TEST PROCEDURE
- Pump 30-QJP-001-1B
Working Step:
1. Close valve AC-2
2. Open the return/bleed line of accumulator CA-11, CA-12
3. Check on PI-1021A, the pressure should back to initial pressure.
4. Close return/bleed line of accumulator CA-11, CA-12
5. Close the line to pump 30-QJP-001-1A (AC-12)
6. Open the line of pump 30-QJP-001-1B (AC-17, AC-18, AC-19)
7. Start the motor and automatically stop the motor if the pressures of the
hydraulic already reach 5500 Psig (Check on PI-1021B and PT-1015).
8. Check the running time duration of the motor to reach the desired operating
pressure.
Working Step :
1. Close valve AC-3
2. Open return line of accumulator CA-5 and CA-6
3. Check the pressure on PI-1020A and PI-1020B, the pressure should back to
initial pressure
4. Close the return line of accumulator CA-5 and CA-6.
5. Close valves AC-9, AC-8, and CD-14.
6. Open Valves AC-3, AC-4, AC-5, AC-6, AC-7, AG-1, CD-13.
7. Open valve AB-11 and start the hand pump until the pressure on PI-1020A
reach 3300 psi
Working Step :
1. Close valve AC-2
2. Open return line of accumulator CA-11 and CA-12
3. Check the pressure on PI-1021A and PI-1021B, the pressure should back to
initial pressure
4. Close the return line of accumulator CA-11 and CA-12.
5. Close valves AC-17, AC-16, and CD-16.
6. Open Valves AC-2, AC-12, AC-13, AC-14, AC-15, Af-1, CD-15.
7. Open valve AB-12 and start the hand pump until the pressure on PI-1021A
reach 6050 psi
For the detailed instruction WHCP Function test fill the WHCP function test Form (Form 3)
NORTH BELUT PROJECT
WHP EPC
PT. NISCONI PT. IBP
TITLE DOCUMENT NUMBER REV DATE PAGE
PERFORMACE TESTING AND
ID-F-NB-P-JP-002-H05-0001 0 26-Dec.-07 8 of 35
ACCEPTANCE TEST PROCEDURE
4 CLEANLINESS TEST
Cleaning test shall be done to check particle contamination level of hydraulic oil
after circulating in the HPU unit. System Cleanliness standard will refer to NAS 1638
class 6 (AEROSPACE INDUSTRIES ASSOCIATION OF AMERICA, INC.).
The result of the checks and measurement done during Factory Acceptance Test
shall be recorded on the following test forms:
A. BODY INSPECTION
CONFORMITY
Aspect To be Checked Yes No N/A
General Aspect
Size (Dimensional Check)
Front Side
Rear Side
Right Side
Left Side
CONFORMITY
Aspect To be Checked Yes No N/A
Equipment Conformity
Equipment Location
Labeling
Cleanliness
Tubing Works
Wiring and Terminations
C. LEAK TEST
Recorded
VISUAL
INPUT OUTPUT
CONTROL
HMI
Display Motor MP1 or MP2 is Turn from Green (Run) to Red (Stop)
HMI
Display SOV HY 1071 is Green
High Pressure
Start Motor (30-QDE-001-1A) & Pump (30-QJP-001-1A) or WHCP
Motor (30-QDE-001-1B) & Pump (30-QJP-001-1B) Pressure gauge MP pump-1A discharge pressure (PI 1021A) or MP pump-1B (PI 1021B) indicate 5,500 psi
LCD Pressure Transmitter (PT 1015) indicate the pressure
HMI
Display Motor HP1 or HP2 is Turn from Green (Run) to Red (Stop)
HMI
Display SOV HY 1070 is Green
HMI
Display for all SOV is Red
VISUAL
INPUT OUTPUT
CONTROL
HMI
Display for all SOV SDY "C" is Red
Display for all SOV SDY "B" is Red
HMI
Display for all SOV SDY "C" is Red
Display for all SOV SDY "B" is Red
Display for all SOV SDY "A" is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-001
Push PB "Open All Valves" (32 HS 1030A) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002A) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001A) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003A) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001A) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001A is Green
Display SOV SDY 1002A is Green
Display SOV SDY 1003A is Green
Push PB " Close All Valves" (32 HS 1032A) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003A) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002A) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001A) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001A) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001A is Red
Display SOV SDY 1002A is Red
Display SOV SDY 1003A is Red
Push PB " Normal Close" (32 HS 1031A) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003A) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002A) will gradually drop to 0 psi
HMI
Display SOV SDY 1003A is Red
Display SOV SDY 1002A is Red
VISUAL
INPUT OUTPUT
CONTROL
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-002
Push PB "Open All Valves" (32 HS 1030B) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002B) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001B) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003B) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001B) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001B is Green
Display SOV SDY 1002B is Green
Display SOV SDY 1003B is Green
Push PB " Close All Valves" (32 HS 1032B) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003B) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002B) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001B) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001B) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001B is Red
Display SOV SDY 1002B is Red
Display SOV SDY 1003B is Red
Push PB " Normal Close" (32 HS 1031B) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003B) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002B) will gradually drop to 0 psi
HMI
Display SOV SDY 1003B is Red
Display SOV SDY 1002B is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-004
Push PB "Open All Valves" (32 HS 1030D) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002D) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001D) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003D) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001D) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001D is Green
Display SOV SDY 1002D is Green
Display SOV SDY 1003D is Green
Push PB " Close All Valves" (32 HS 1032D) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003D) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002D) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001D) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001D) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001D is Red
Display SOV SDY 1002D is Red
Display SOV SDY 1003D is Red
Push PB " Normal Close" (32 HS 1031D) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003D) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002D) will gradually drop to 0 psi
HMI
Display SOV SDY 1003D is Red
Display SOV SDY 1002D is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-005
Push PB "Open All Valves" (32 HS 1030E) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002E) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001E) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003E) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001E) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001E is Green
Display SOV SDY 1002E is Green
Display SOV SDY 1003E is Green
Push PB " Close All Valves" (32 HS 1032E) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003E) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002E) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001E) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001E) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001E is Red
Display SOV SDY 1002E is Red
Display SOV SDY 1003E is Red
Push PB " Normal Close" (32 HS 1031E) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003E) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002E) will gradually drop to 0 psi
HMI
Display SOV SDY 1003E is Red
Display SOV SDY 1002E is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-008
Push PB "Open All Valves" (32 HS 1030H) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002H) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001H) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003H) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001H) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001H is Green
Display SOV SDY 1002H is Green
Display SOV SDY 1003H is Green
Push PB " Close All Valves" (32 HS 1032H) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003H) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002H) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001H) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001H) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001H is Red
Display SOV SDY 1002H is Red
Display SOV SDY 1003H is Red
Push PB " Normal Close" (32 HS 1031H) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003H) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002H) will gradually drop to 0 psi
HMI
Display SOV SDY 1003H is Red
Display SOV SDY 1002H is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-009
Push PB "Open All Valves" (32 HS 1030I) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002I) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001I) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003I) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001I) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001I is Green
Display SOV SDY 1002I is Green
Display SOV SDY 1003I is Green
Push PB " Close All Valves" (32 HS 1032I) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003I) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002I) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001I) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001I) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001I is Red
Display SOV SDY 1002I is Red
Display SOV SDY 1003I is Red
Push PB " Normal Close" (32 HS 1031I) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003I) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002I) will gradually drop to 0 psi
HMI
Display SOV SDY 1003I is Red
Display SOV SDY 1002I is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-011
Push PB "Open All Valves" (32 HS 1030K) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002K) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001K) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003K) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001K) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001K is Green
Display SOV SDY 1002K is Green
Display SOV SDY 1003K is Green
Push PB " Close All Valves" (32 HS 1032K) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003K) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002K) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001K) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001K) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001K is Red
Display SOV SDY 1002K is Red
Display SOV SDY 1003K is Red
Push PB " Normal Close" (32 HS 1031K) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003K) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002K) will gradually drop to 0 psi
HMI
Display SOV SDY 1003K is Red
Display SOV SDY 1002K is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-012
Push PB "Open All Valves" (32 HS 1030L) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002L) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001L) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003L) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001L) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001L is Green
Display SOV SDY 1002L is Green
Display SOV SDY 1003L is Green
Push PB " Close All Valves" (32 HS 1032L) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003L) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002L) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001L) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001L) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001L is Red
Display SOV SDY 1002L is Red
Display SOV SDY 1003L is Red
Push PB " Normal Close" (32 HS 1031L) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003L) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002L) will gradually drop to 0 psi
HMI
Display SOV SDY 1003L is Red
Display SOV SDY 1002L is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-013
Push PB "Open All Valves" (32 HS 1030M) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002M) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001M) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003M) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001M) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001M is Green
Display SOV SDY 1002M is Green
Display SOV SDY 1003M is Green
Push PB " Close All Valves" (32 HS 1032M) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003M) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002M) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001M) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001M) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001M is Red
Display SOV SDY 1002M is Red
Display SOV SDY 1003M is Red
Push PB " Normal Close" (32 HS 1031M) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003M) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002M) will gradually drop to 0 psi
HMI
Display SOV SDY 1003M is Red
Display SOV SDY 1002M is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-014
Push PB "Open All Valves" (32 HS 1030N) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002N) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001N) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003N) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001N) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001N is Green
Display SOV SDY 1002N is Green
Display SOV SDY 1003N is Green
Push PB " Close All Valves" (32 HS 1032N) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003N) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002N) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001N) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001N) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001N is Red
Display SOV SDY 1002N is Red
Display SOV SDY 1003N is Red
Push PB " Normal Close" (32 HS 1031N) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003N) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002N) will gradually drop to 0 psi
HMI
Display SOV SDY 1003N is Red
Display SOV SDY 1002N is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-016
Push PB "Open All Valves" (32 HS 1030P) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002P) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001P) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003P) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001P) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001P is Green
Display SOV SDY 1002P is Green
Display SOV SDY 1003P is Green
Push PB " Close All Valves" (32 HS 1032P) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003P) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002P) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001P) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001P) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001P is Red
Display SOV SDY 1002P is Red
Display SOV SDY 1003P is Red
Push PB " Normal Close" (32 HS 1031P) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003P) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002P) will gradually drop to 0 psi
HMI
Display SOV SDY 1003P is Red
Display SOV SDY 1002P is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-017
Push PB "Open All Valves" (32 HS 1030Q) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Q) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001Q) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Q) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001Q) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001Q is Green
Display SOV SDY 1002Q is Green
Display SOV SDY 1003Q is Green
Push PB " Close All Valves" (32 HS 1032Q) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Q) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Q) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001Q) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001Q) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001Q is Red
Display SOV SDY 1002Q is Red
Display SOV SDY 1003Q is Red
Push PB " Normal Close" (32 HS 1031Q) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Q) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Q) will gradually drop to 0 psi
HMI
Display SOV SDY 1003Q is Red
Display SOV SDY 1002Q is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-020
Push PB "Open All Valves" (32 HS 1030T) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002T) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001T) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003T) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001T) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001T is Green
Display SOV SDY 1002T is Green
Display SOV SDY 1003T is Green
Push PB " Close All Valves" (32 HS 1032T) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003T) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002T) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001T) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001T) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001T is Red
Display SOV SDY 1002T is Red
Display SOV SDY 1003T is Red
Push PB " Normal Close" (32 HS 1031T) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003T) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002T) will gradually drop to 0 psi
HMI
Display SOV SDY 1003T is Red
Display SOV SDY 1002T is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-021
Push PB "Open All Valves" (32 HS 1030U) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002U) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001U) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003U) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001U) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001U is Green
Display SOV SDY 1002U is Green
Display SOV SDY 1003U is Green
Push PB " Close All Valves" (32 HS 1032U) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003U) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002U) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001U) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001U) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001U is Red
Display SOV SDY 1002U is Red
Display SOV SDY 1003U is Red
Push PB " Normal Close" (32 HS 1031U) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003U) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002U) will gradually drop to 0 psi
HMI
Display SOV SDY 1003U is Red
Display SOV SDY 1002U is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-023
Push PB "Open All Valves" (32 HS 1030W) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002W) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001W) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003W) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001W) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001W is Green
Display SOV SDY 1002W is Green
Display SOV SDY 1003W is Green
Push PB " Close All Valves" (32 HS 1032W) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003W) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002W) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001W) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001W) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001W is Red
Display SOV SDY 1002W is Red
Display SOV SDY 1003W is Red
Push PB " Normal Close" (32 HS 1031W) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003W) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002W) will gradually drop to 0 psi
HMI
Display SOV SDY 1003W is Red
Display SOV SDY 1002W is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-024
Push PB "Open All Valves" (32 HS 1030X) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002X) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001X) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003X) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001X) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001X is Green
Display SOV SDY 1002X is Green
Display SOV SDY 1003X is Green
Push PB " Close All Valves" (32 HS 1032X) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003X) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002X) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001X) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001X) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001X is Red
Display SOV SDY 1002X is Red
Display SOV SDY 1003X is Red
Push PB " Normal Close" (32 HS 1031X) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003X) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002X) will gradually drop to 0 psi
HMI
Display SOV SDY 1003X is Red
Display SOV SDY 1002X is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-025
Push PB "Open All Valves" (32 HS 1030Y) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Y) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001Y) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Y) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001Y) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001Y is Green
Display SOV SDY 1002Y is Green
Display SOV SDY 1003Y is Green
Push PB " Close All Valves" (32 HS 1032Y) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Y) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Y) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001Y) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001Y) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001Y is Red
Display SOV SDY 1002Y is Red
Display SOV SDY 1003Y is Red
Push PB " Normal Close" (32 HS 1031Y) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Y) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Y) will gradually drop to 0 psi
HMI
Display SOV SDY 1003Y is Red
Display SOV SDY 1002Y is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-026
Push PB "Open All Valves" (32 HS 1030Z) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Z) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001Z) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Z) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001Z) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001Z is Green
Display SOV SDY 1002Z is Green
Display SOV SDY 1003Z is Green
Push PB " Close All Valves" (32 HS 1032Z) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Z) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Z) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001Z) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001Z) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001Z is Red
Display SOV SDY 1002Z is Red
Display SOV SDY 1003Z is Red
Push PB " Normal Close" (32 HS 1031Z) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003Z) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002Z) will gradually drop to 0 psi
HMI
Display SOV SDY 1003Z is Red
Display SOV SDY 1002Z is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-028
Push PB "Open All Valves" (32 HS 1030AB) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002AB) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001AB) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003AB) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001AB) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001AB is Green
Display SOV SDY 1002AB is Green
Display SOV SDY 1003AB is Green
Push PB " Close All Valves" (32 HS 1032AB) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003AB) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002AB) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001AB) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001AB) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001AB is Red
Display SOV SDY 1002AB is Red
Display SOV SDY 1003AB is Red
Push PB " Normal Close" (32 HS 1031AB) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003AB) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002AB) will gradually drop to 0 psi
HMI
Display SOV SDY 1003AB is Red
Display SOV SDY 1002AB is Red
VISUAL
INPUT OUTPUT
CONTROL
♦ Well 32QAY-029
Push PB "Open All Valves" (32 HS 1030AC) to Open the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge SSV Valve hydraulic pressure (32-PI-1002AC) will indicate 3,000 psi
Opening Sequence are; Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001AC) will indicate 5,500 psi
1st SSV valve Pressure gauge Wing Valve hydraulic pressure (32-PI-1003AC) will indicate 3,000 psi
2nd SCSSV valve LCD Pressure Transmitter (PT 1001AC) will indicate the pressure
3rd Wing valve
HMI
Display SOV SDY 1001AC is Green
Display SOV SDY 1002AC is Green
Display SOV SDY 1003AC is Green
Push PB " Close All Valves" (32 HS 1032AC) to close the well WHCP
Sequence for opening will be done at PLC logic Pressure gauge Wing Valve hydraulic pressure (32-PI-1003AC) will gradually drop to 0 psi
Closing Sequence are; Pressure gauge SSV Valve hydraulic pressure (32-PI-1002AC) will gradually drop to 0 psi
1st Wing valve Pressure gauge SCSSV Valve hydraulic pressure (32-PI-1001AC) will gradually drop to 0 psi
2nd SSV valve LCD Pressure Transmitter (PT 1001AC) will gradually drop to 0 psi
3rd SCSSV valve
HMI
Display SOV SDY 1001AC is Red
Display SOV SDY 1002AC is Red
Display SOV SDY 1003AC is Red
Push PB " Normal Close" (32 HS 1031AC) to close Wing & SSV WHCP
Pressure gauge Wing Valve hydraulic pressure (32-PI-1003AC) will gradually drop to 0 psi
Pressure gauge SSV Valve hydraulic pressure (32-PI-1002AC) will gradually drop to 0 psi
HMI
Display SOV SDY 1003AC is Red
Display SOV SDY 1002AC is Red
VISUAL
INPUT OUTPUT
CONTROL
☼ WIRELINE BY PASS
Medium Pressure
Switch Selector (HS 1076) to bypass wireline WHCP
Turn off all SOV SDY "B" Common Section
Switch 3 way selector valve (EC) to bypass wireline Pressure gauge MP hydraulic wireline header (32 PI 1086) will indicate pressure
Wellhead Module
Pressure gauge SSV Valve hydraulic pressure for each module Tag below will indicate 3,000 psi
(32-PI-1002A)
(32-PI-1002B)
(32-PI-1002D)
(32-PI-1002E)
(32-PI-1002H)
(32-PI-1002I)
(32-PI-1002K)
(32-PI-1002L)
(32-PI-1002M)
(32-PI-1002N)
(32-PI-1002P)
(32-PI-1002Q)
(32-PI-1002T)
(32-PI-1002U)
(32-PI-1002W)
(32-PI-1002Y)
(32-PI-1002Z)
(32-PI-1002AB)
(32-PI-1002AC)
HMI
Display SOV HY 1076 is Green
Display for all SOV SDY "B" is Red
High Pressure
Switch Selector (HS 1075) to bypass wireline WHCP
Turn off all SOV SDY "C" Common Section
Switch 3 way selector (EB) valve to bypass wireline Pressure gauge MP hydraulic wireline header (32 PI 1085) will indicate pressure
Wellhead Module
Pressure gauge SCSSV Valve hydraulic pressure for each module Tag below will indicate 5,500 psi
(32-PI-1001A)
(32-PI-1001B)
(32-PI-1001D)
VISUAL
INPUT OUTPUT
CONTROL
(32-PI-1001E)
(32-PI-1001H)
(32-PI-1001I)
(32-PI-1001K)
(32-PI-1001L)
(32-PI-1001M)
(32-PI-1001N)
(32-PI-1001P)
(32-PI-1001Q)
(32-PI-1001T)
(32-PI-1001U)
(32-PI-1001W)
(32-PI-1001Y)
(32-PI-1001Z)
(32-PI-1001AB)
(32-PI-1001AC)
HMI
Display SOV HY 1075 is Green
Display for all SOV SDY "A" is Red
ACTION CLEARANCE
No. PUNCH LIST DESCRIPTION REMARKS
BY STATUS