Model 450 Series II

User Guide
WIRING CONNECTIONS
Refer to Figure 1 and Table 1 below. For unbalanced operation, the GREEN
wire is connected to the audio input, the WHITE wire is connected to the audio
ground, and the SHIELD is connected to chassis ground. In some cases, audio
ground and chassis ground will be the same.
For balanced operation, the GREEN wire is connected to the positive audio
input, the WHITE wire is connected to the negative audio input, and the SHIELD
is connected to chassis ground.

IMPEDANCE SWITCH PRESS-TO-TALK SWITCH

GREEN YELLOW

1 2 3
LO HI
BLACK
RED
BLACK GREEN

WHITE
WHITE

GREEN
SHIELD

ORANGE

SHURE MODEL 450 SERIES II RED

PAGING AND DISPATCHING MICROPHONE

The Shure Model 450 Series II is a high output dynamic micro- WIRING DIAGRAM
phone designed for paging and dispatching applications. This FIGURE 1
extremely rugged microphone features an omnidirectional pickup
pattern and a frequency response tailored for optimum speech in- Table 1. Typical Cable-to-Connector Wiring
telligibility. It also includes an impedance selection switch and a
locking press-to-talk switch. INPUT TYPE WIRE FUNCTION XLR 1/4 IN.
COLOR CONNECTOR PHONE
Features JACK
• Dual impedance GREEN AUDIO PIN 2 TIP
• Locking press-to-talk switch AUDIO PIN 3 SLEEVE
WHITE
• Rugged ARMO-DUR® base and case UNBALANCED GROUND

• Adjustable height CHASSIS PIN 1 SLEEVE

SHIELD
GROUND
PRESS-TO-TALK SWITCH OPERATION
GREEN AUDIO + PIN 2 TIP
To operate the control bar as a press-to-talk switch, simply hold
WHITE AUDIO - PIN 3 RING
it down and begin speaking. When you are finished speaking, re- BALANCED
lease the control bar. CHASSIS PIN 1 SLEEVE
SHIELD
GROUND
To lock the control bar in the “on” position, press it down and pull it
forward. To unlock the control bar, push it back and release it. NOTE: The RED and BLACK leads are not part of the audio circuit. These wires
IMPEDANCE SELECTION provide a contact closure when the press-to-talk switch is depressed. This clo-
sure may be used to control an external relay or a transmit/receive circuit.
To select high or low impedance, move the impedance selection
switch, located under the microphone base, to either the HIGH or
LO position. The switch is factory pre-set to LO. CHANGING PTT CIRCUIT TO NORMALLY OPEN
Shure recommends the low impedance setting if long lengths of Using microphones in parallel requires a normally open microphone circuit. To
cable are used, or if severe hum is encountered. Use Shure A95 modify the press-to-talk switch so that it provides a normally open circuit, proceed
Line Matching Transformers to match a low impedance (300 W) as follows:
microphone line to a high impedance amplifier input. 1. Remove the screws, washers, and bottom plate from the microphone.
2. Unsolder the black, red, and white leads from the terminal of the press–
to–talk switch (see Figure 1). Make sure these leads are still soldered
together. If necessary, resolder them and insulate the connection.
3. Replace the bottom plate and secure it with the screws and washers
removed in Step 1.

27C2917 (Rev. 5) Printed in U.S.A.

©2012 Shure Incorporated
SPECIFICATIONS Case
Two-tone gray ARMO-DUR
Type
Dynamic
Frequency Response
200 to 5,000 Hz (see Figure 2)

TYPICAL FREQUENCY RESPONSE

FIGURE 2
Polar Pattern
Omnidirectional OVERALL DIMENSIONS

Impedance (at 1,000 Hz) FIGURE 3

High Impedance: 40,000 Ω Net Weight
Low Impedance: 210 Ω 737 grams (1 lb., 10 oz.)
Recommended Load Impedance Shipping Weight
High Impedance: 100,000 Ω 1020 grams (2 lb., 4 oz.)
Low Impedance: 1,000 Ω Certification
Output Level (at 1,000 Hz, Open Circuit Voltage) Conforms to European Union directives, eligible to bear CE marking; meets
High Impedance Low Impedance European Union EMC Immunity Requirements (EN 50082–1, 1992).
–35.0 dBV/Pa* –57.0 dBV/Pa*
(17.8 mV) (1.4 mV)
REPLACEMENT PARTS
*1 Pa = 94 dB SPL Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R96
Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C31C
Switches
On/Off Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RK141S
Locking Press-to-Talk Switch: Activates microphone circuit and an
external relay or control circuit. The microphone circuit is normally
shorted.
Impedance Selection Switch: Double-pole, double-throw slide switch
located in the base of the microphone.
Cable
2.1 m (7 ft.) four-conductor, two conductors shielded,
non-detachable

United States, Canada, Latin Europe, Middle East, Africa: Asia, Pacific:
America, Caribbean: Shure Asia Limited
Shure Europe GmbH
Shure Incorporated 22/F, 625 King’s Road
Jakob-Dieffenbacher-Str. 12,
5800 West Touhy Avenue North Point, Island East
75031 Eppingen, Germany
Niles, IL 60714-4608 USA Hong Kong
Phone: 847-600-2000 Phone: 49-7262-92490 Phone: 852-2893-4290
Fax: 847-600-1212 (USA) Fax: 49-7262-9249114 Fax: 852-2893-4055
Fax: 847-600-6446 Email: [email protected] Email: [email protected]
Email: [email protected]
www.shure.com ©2012 Shure Incorporated