Navigasi

Download as pdf or txt
Download as pdf or txt
You are on page 1of 87

malesbanget38_crew.

com

19. Plan And Ensure Safe Loading, Stowage, Securing, Care During
Voyage And Unloading Of Cargoes.

1. A bulk cargo is loaded and the cargo stow has been left with an excessive peak
height; what could be the result of this situation?
Excessive stresses on tank top
2. A bulk cargo vessel is found to be 4.0 centimetres over her maximum loadline draft
after loading; what should be the actions of the master?
Order the pumping out of fresh water or ballast until the
maximum allowed loadline is achieved.
3. A bulk carrier is to carry a full deck cargo of packaged timber; to what regulations
must the vessel comply?
IMO Code of Practice for the carriage of
Timber Deck cargoes
4. During a pre-loading survey prior to loading grain on a Bulk Carrier, very small
amount of the previous grain cargo is found in a cargo hold; what is the
significance of this situation?
The vessel may fail the pre-load survey and
be declared off-hire

5. How should mild steel slabs be loaded in a bulk carrier?


Interlocked across the entire cargo hold with the longitudinal axes
athwartships

6. What are the advantages of ballasting double bottom ballast tanks by gravity filling on a
Bulk Carrier?
There is minimum pressure head
on the tank top and pumps are not
required
7. What could happen if a bulk vessel failed to display placards notifying the crew of the
disposal of garbage within and outside Special Areas?
The vessel could be detained by
port state control authorities
8. What governs the disposal of dry bulk cargo
residues at sea?

MARPOL regulations
9. What is essential to ensure that efficient stripping of ballast tanks on a Bulk Carrier can
be achieved?
A good stern trim is maintained
during de- ballasting operations
10. What is the possible concern if fuel tanks on a Bulk Carrier, which are close to cargo
spaces containing grain, are excessively heated?
The grain cargo may be heated and
damaged

11. What is the purpose of a draught survey before and after loading on a Bulk Carrier?
To ascertain the actual weight of cargo loaded

12. What measures should be taken in order to avoid flammable gases forming on top of
coal cargoes on a Bulk Carrier?
Ventilation to be carried out as indicated in the IMO solid Bulk Cargo Code

13. What must be ensured, prior to receiving a bulk cargo of iron ore on a Bulk Carrier?
Cargo hold bilge suctions must be satisfactorily tested

14. What publication must be carried on a vessel carrying dry bulk cargoes?
IMO Solid Bulk cargo Code or IMO Solid Bulk?

15. When considering how to deal with cargo residues during hatch cleaning at sea on a
Bulk Carrier, what is the most careful consideration?
Consult MARPOL handbook and the vessels Safety Management System
(SMS) for guidance

16. Which of these covers the rules and regulations for General Average on a Bulk Carrier?
The York Antwerp

17. Which special regulations cover transportation of grain on a Bulk Carrier?


IMO Grain Rules?

18. Which special regulations cover transportation of solid Bulk cargoes?


IMO Bulk Cargoes Code (BC) and the IMO International Maritime Solid
Bulk Cargo Code( IMSBC)

19. Why do structural steel products often shift or collapse in a bulk carrier's cargo holds?
Because the irregular shape of the cargo holds results in void spaces

20. Why is air draught an important consideration when loading bulk cargoes on Bulk
Carriers?
Because of movement of the bulk cargo loader or unloaders

21. A container vessel has lost several dangerous goods containers overboard. The master
must report this loss of container incident to:
The nearest Coastal state.

22. A heavy piece of machinery is loaded on deck of a container vessel, stowed across
several flat rack containers. The most appropriate method for lashing such cargo would be
by:
Taking all lashings to the flat-rack lashing points.
23. Besides normal loads, the lashings of the containers stowed at the outboard part of the
deck stow are additionally subjected to:
The effect of wind on the containers.

24. Best location to stow containers loaded with Calcium Hypochlorite would be:
On deck, away from sources of heat.

25. Bulk liquid cargoes carried in flexi-tank containers are considered dangerous:
When the associated material safety data sheet shows a constituent(s) listed
in the IMDG Code.

26. During a loaded winter passage across the North Atlantic, the master of a container
vessel would be most concerned with:
The added weight of icing on container stacks,
leading to loss of GM.
27. During a loaded winter passage across the North Atlantic, the master of a container
vessel would be most concerned with:
Metacentric height of the vessel.

28. For guidance on lashing arrangement of containers on-board the vessel, the most
important document to refer is:
The Cargo Securing Manual.

29. On multi-purpose vessels, responsibility for the stowage and securing of containers is:
Determined by the clauses of the charter-party.
30. The Code of Safe Practice for Cargo Stowage and Securing was prepared to give
guidance for:
Preparation and content of the Cargo Securing
31. The dangers associated with carriage of empty tank
containers is that:
They may contain flammable cargo residue.

32. The direction of wave encounter that is most likely to cause a parametric roll condition
on large container ships is:
Head seas.

33. The most appropriate measure to reduce the build-up of ice on containers during a sea
passage is to:
Reduce speed, whilst maintaining course.

34. The most appropriate method for adjusting the trim on a container vessel would be:
By internal shift of ballast
35. What is the master's position if he is asked to load a container that is incorrectly
manifested, but which is believed to contain dangerous goods, about which insufficient
information is supplied?
He has the authority to refuse it.

36. When taking action to deal with under-deck cargo spillage on container ships, reference
must be made to:
The ems Guide.

37. With regards to carriage of Calcium Hypochlorite in containers, as per IMDG Code it
is not allowed to:
Ship in Intermediate Bulk Containers (ibcs)
38. A chemical tanker may be granted, by the Government
of the receiving Party, an exemption from carrying out a
mandatory prewash provided that the:
Unloaded tank is to be reloaded with the same
substance or another substance compatible with
the previous one and that the tank will not be
washed or ballasted prior to loading.
39. A tank which contained a category "X" product must undergo a prewash before leaving
port in compliance with MARPOL. The resulting residues shall be discharged to a
reception facility until the concentration of the substance in the effluent, as indicated by
analysis of samples of the effluent taken by the authorized surveyor has reached a level of:
0.1 % by weight.

40. As per MARPOL, for control of discharge of Noxious Liquid Substances, the area(s)
designated as ―Special Areas‖ are:
The Antarctic.

41. Ballast introduced into a cargo tank on a chemical tanker which has been washed to
such an extent that the ballast contains less than 1 ppm of the substance previously carried
may be discharged into the sea without regard to the discharge rate, ship's speed and
discharge outlet location, but under certain conditions, which require:
That the vessel is not less than 12 miles from the nearest land and is in water
that is not less than 25 metres deep.

42. Cargo residues of certain chemical substances are permitted to be removed by


ventilation. This may be carried out provided that:
The cargo discharged has a vapour pressure greater than 5 kpa at 20 degrees Celsius
43. Definitive information on whether a particular cargo is classified as a ―Noxious
Liquid Substance‖ (other than products provisionally assessed) can be obtained from:
The pollution category column of chapters 17 or 18 of the International
Bulk Chemical Code (IBC Code).

44. If a cargo tank on a chemical tanker is to be cleaned by recirculation with a low flash
or static accumulator product:
The tank must be inerted to less than 8% oxygen content.

45. In respect of a chemical tanker, carrying category ―X‖, ―Y‖ & ―Z‖ Noxious Liquid
Substances, the term ―Clean Ballast‖ as defined in the IBC Code means:
Ballast water carried in a tank which, since it was last used to carry a cargo
containing a substance in category "X","Y" or "Z", has been thoroughly
cleaned and the residues resulting there from have been discharged and the
tank emptied in accordance with the appropriate requirements of Annex II.

46. In the event of an accidental or other exceptional discharge into the sea of a Noxious
Liquid Substance or mixture containing such a substance, an entry shall be made in the
Cargo record Book, which shall include:
Time of occurrence

47. The ‗dew point‘ of a liquid chemical can be defined as:


The temperature at which a gas is saturated with respect to a condensable
component, as in operational terms is seen at the point when air is saturated
with moisture.
48. The carriage of a new Noxious Liquid Substance not yet listed in the IBC Code may be
considered possible, provided it is achieved through a ‗tri-partite‖ agreement between:
The Port State of the Shipper / the Flag State of the Carrier / the Port State
of the Receiver.

49. The chemical term for a substance used as an additive to start a chemical reaction and
speed up the cleaning of a cargo tank on a chemical tanker is:
Catalyst.

50. The document which confirms whether a chemical tanker is authorised to carry a
particular Noxious Liquid Substance, is called:

The International Pollution Prevention Certificate for the Carriage of


Noxious Liquid Substances in Bulk.

51. The tank cleaning requirements for a Category ―X‖ substance on a chemical tanker
constructed after 01 January 2007, require the vessel to carry out:
Prewash / strip to 75 litres / 12 miles from land / 25 metres of water /
minimum 7 knots, proceeding en route / discharge below waterline.

52. Vegetable Oils as per MARPOL are classified under:


Category "Y".

53. What is the name given to the risk assessment programme developed by OCIMF, under
which tankers are inspected and the results made available to potential charterers through a
database of records?
The Ship Inspection Report Programme
(SIRE)
54. When cleaning a cargo tank after carriage and discharge of Sulphuric Acid, it is
important to ensure that:
Once cleaning commences, large quantities of washing water can be
delivered as quickly as possible, so that the acid is quickly diluted.

55. When small amounts of cleaning additives (detergent products) are added to water in
order to facilitate the washing of tanks which previously contained liquid chemicals, must
be ensured that:
No additives containing Pollution Category "X" components shall be used,
except those components that are readily biodegradable and present in a
total concentration of less than 10% of the cleaning additive. No restrictions
additional to those applicable to the tank due to the previous cargo shall
apply.

56. You are to load a number of chemical cargoes in Rotterdam in December, for eventual
discharge in Australia, after the ship has called at Singapore and Malaysia. None of the
cargoes on board at any stage of the voyage require heating. None of the tanks to be
discharged in Singapore and Malysia will require hot washing after discharge. When
determining the filling limits of the tanks containing the Australian cargoes, you will need
to consider that:
The maximum anticipated temperature that the cargoes will reach bearing in
mind ambient air and sea temperatures to be encountered on passage, so that
any expansion does not result in overflow.
57. A greater number of lashings may generally be required to secure cargo forward on
deck compared with amidships under deck of a General Cargo Vessel, because:
The dynamic stresses on the lashing are much greater in the forward areas
of the vessel.

58. A loaded General Cargo ship is bound from Brazil to Rotterdam during winter time.
During the voyage, ventilation in cargo spaces should:
Be carried out during voyage, as the vessel is
moving from warm to colder areas.

59. Additional lashings on general cargoes must be considered when:


Heavy weather is anticipated for the planned
voyage.

60. For a General Cargo ship not specifically designed for carriage of containers, the
maximum stowage height for containers on deck is limited to:
One container high.
61. For a General Cargo ship to load Dangerous Goods in packaged form, it must have on board
a:Document of Compliance for carriage of dangerous goods.

62. For special category spaces on board general cargo ship, the minimum required air
changes per hour should be:
6

63. Information on the forces that may cause cargo shifting on a general cargo vessel may
be available by referring to:
The Cargo Stowage and Security (CSS)
Code.
64. On a voyage from cold to hot climate countries, the ventilation of cargo holds of a
General cargo ship should:
Not be carried out at all.

65. On a voyage from hot to cold climate countries, the ventilation of cargo holds of a
General cargo ship should:
Be carried out continuously during the voyage

66. The IMO Cargo Stowage and Securing Code (CSS) indicates in the 'Rule of Thumb',
the total strength of the lashings on each side of a heavy lift; what is the stated value ?
The Maximum Securing load of the
lashings must equal the weight of
the cargo unit.

67. The minimum information to that must be provided be given on a dangerous goods
declaration on a General Cargo Vessel should be:
IMO Class, UN Number, Gross
weight, number of units of cargo,
Proper Shipping Name.
68. The most important consideration when planning the lashing system for a particular sea
route on a General Cargo Vessel is:
Transverse accelerations.
69. The segregation requirements for Dangerous Goods to be loaded on a General Cargo
ship may be obtained by referring to:
The IMO International Maritime
Dangerous Goods Code.
70. The two main considerations when choosing an appropriate paint for a cargo space of a
General Cargo vessel would be:

Corrosion resistant and heat


resistant.

71. Which of these can be loaded in the same hold of a General Cargo Vessel, as steel
coils?
Steel rebars

72. How can you best demonstrate in an audit that you follow company cargo handling
procedures?
By being able to provide comprehensive and
verifiable documentary records of cargo
operations.

73. If all indications are that a cargo has been received without damages, irregularities or
short shipment and the phrase "apparent good order and condition" is entered on the Bill of
Lading, what type of Bill is this said to be?
A clean Bill of Lading.

74. What may be issued by the shipper to indicate that a vessel or her operators will not be
held responsible for any damage that may arise from the carrier issuing a clean Bill of
Lading, even though the Mate's receipt is marked as "unclean", such as may apply to
atmospheric corrosion on steel plates that have been waiting in a port facility for some time
awaiting shipment?
A Letter of Indemnity.
75. What term is applied to the compensation payment by the charterer that is due when a
vessel is unable to load / discharge her cargo within the allowed and contracted time?
Demurrage.

76. What type of Bill of Lading covers "door to door" shipment?


A Through Bill of Lading.

77. When conducting a risk assessment for a shipboard work activity, what are the two
elements to be considered?
The potential severity of harm and the likelihood
that harm will occur.
78. According to SIGTTO publications, what is a typical accuracy for LNG pressure
measurement equipment?
+/- 0,0015 bar (which will apply within the
MARVS of the tank)

79. According to the IMO Gas Codes, what is the minimum number of "Firemen‘s outfits"
required to be carried on an LNG carrier with a cargo capacity above 5,000 m3?
5 sets

80. Carbon dioxide, CO2, can solidify and form dry ice at low temperatures. What is the
solidifying temperature of CO2?
Approximately minus 78.5 C

81. Does MARPOL apply to LNG carriers?


Yes, MARPOL applies to all ship types..

82. Does the Oil Pollution Act, 1990 (OPA90) apply to vessels engaged in carrying
liquefied natural gas (LNG)?
Yes, OPA90 applies to all ships.

83. Due to the very low carriage temperatures for LNG the thermal conductivity, k value, is
an important property of the insulation material used in cargo containment systems. For a
given rate of heat leakage across the insulation, which of the following statements is true?

The rate of heat leakage is


unaffected by the thickness of the
insulation.

84. During cargo tank gassing up and cooling down operations on an LNG carrier which of
the given options, regarding temperature, needs to be observed?
Never allow temperature of the insulation to fall
below the safe minimum temperature.

85. Having water vapour in an LNG carriers cargo tanks prior to loading cargo is
unacceptable due to ice formation at low carriage temperatures. How can water vapour in
the tank atmosphere be removed prior to the cooling down and loading operation?
By displacing the tank atmosphere with pre-dried inert
gas.

86. What is the approximate normal daily cargo "boil off" rate for an LNG carrier of
125000 cubic metre cargo capacity?
From 0,15 % to 0,20 % per day of total cargo.

87. What is the normal procedure for cooling down the a cargo tank prior to loading LNG?
Introducing liquid LNG into the tank slowly through the spray

88. What is the typical accuracy for onboard LNG temperature measurement systems? +/-
0.2 C in the range of - 150 C / - 170 C
89. Which of the gas groups, identified by SIGTTO, in 'Liquid Gas Handling Principles on
Ships and in Terminals', does LNG belong to?
Saturated Hydrocarbons

90. Which term is usually used to describe the compressor that collects the boil-off from
the header connected to each cargo tank of an LNG carrier?
The low-duty compressor.

91. Why is nitrogen used for the inerting of hold spaces and interbarrier spaces on LNG
carriers?
Because the carbon dioxide in
combustion generated inert gas
would freeze when in close
proximity to the cargo.

92. With reference to preparations of LNG carrier cargo tanks for cargo loading operations,
how can it be determined that the cool down operation is complete?
When temperature monitor, or liquid level
gauge, shows that liquid is forming in the
bottom of the cargo tank.

93. Before loading a refrigerated cargo of LPG the cargo tanks must be cooled down
slowly in order to minimise thermal stresses for the vessel and the cargo containment
system. What is the generally accepted cooling down rate?
10 degrees C per hour.

94. Cargo tanks on an LPG carrier can be inerted using either inert gas from a combustion
type inert gas generator or by using nitrogen. Is gassing up of an inerted cargo tank with
LPG allowed when the tank contains combustion generated inert gas?

Yes, it is always allowed if the atmosphere of the inerted tank has an


oxygen content of less than 5% by volume.

95. During pre-entry checks of an enclosed space onboard a liquefied gas carrier it is
necessary to check the condition of the atmosphere. If the gas detection equipment to be
used for the checks included a catalytic type combustible gas indicator, an absorption type
toxic gas detector and a paramagnetic type oxygen analyser, which would be the preferred
order for the checks?
Oxygen content followed by
hydrocarbon gas content and then
toxic gas content.
96. IMO publishes a number of Codes relating to the carriage of bulk cargoes including the
IGC Code for liquefied gas carriers. What is the main purpose of the IGC Code?
To provide an international standard for the
construction of, and equipment for, gas carriers
to ensure the safe carriage of liquefied gases in
bulk.

97. Inhibitors are often added to liquefied gas cargoes prior to loading to prevent or slow
down polymerisation. An inhibitor information form or certificate must be provided by the
cargo shipper to the vessel. What sort of information must this certificate contain about the
inhibitor in addition to the technical name and quantity added?

Expected lifetime of the inhibitor and the date the cargo tanks were
inhibited

98. Is it permitted to load fully refrigerated propane directly onto a fully pressurised
LPG carrier without additional conditioning of the cargo or cargo spaces?
Only if the cargo containment
system is designed for temperatures
of minus 48 degrees C or less.

99. It is necessary for personnel to enter a liquefied gas carrier cargo tank to clean up
some dust and other loose debris. What are the permit requirements before entry
into the tank is allowed?

Only an Enclosed Space Entry


Permit is required.

100. Liquefied gas cargoes will expand as the temperature increases and therefore tanks are
not allowed to be filled to 100%. What is the maximum allowable filling limit for the cargo
tanks on liquefied gas carriers?
Maximum allowable filling limit on cargo tanks is 98% on gas carriers.

101. What is the full title of the IMO code which applies to all gas carriers built after
1986?
The International Code for the Construction and
Equipment of Ships Carrying Liquefied Gases in
Bulk (the IGC Code)

102. What is the main reason for adding inhibitors to some liquefied gas cargoes such as
ethylene oxide and vinyl chloride?

To control the temperature of the cargo.


103. What is the requirement for the atmosphere in the hold spaces surrounding cargo
tanks that require a secondary barrier when carrying LPG cargoes?
The hold spaces must be kept in an inert condition
whenever there is cargo in the cargo tanks.

104. What method should be used to discharge a semi-pressurised gas carrier if there is a
break down on the cargo discharge pump?
By using a portable submersible pump to empty
the affected tank By using the cargo compressor to
pump the cargo vapour ashore as it boils off.

105. When a ship is switching from ammonia to LPG virtually all traces of vapours must
be removed. What is the allowable concentration of ammonia vapour in the tank prior to
loading the next cargo?
Less than 20 parts per million.

106. Which certificate is issued to LPG and other liquefied gas carriers in accordance with
the IGC code?
The Certificate of Fitness is issued
in accordance with the IGC code

107. With some liquefied gas cargoes special conditions must be met before they can be
loaded into a cargo tank. Is it permitted load ammonia into an inerted cargo tank?
Ammonia cannot be loaded into any tank with an inert atmosphere.

108. A VLCC is to anchor in a depth of 80 meters in open water with moderate swell
running. How many shackles of anchor chain should be used to aid a safe anchorage?
11 shackles

109. After the last entry being made, the retention period of an oil record book on board
must be:
Not less than 3 years after the date
of the last entry.

110. Any person who can assume overall charge of the ships crude oil washing operation
must have:
At least 12 months appropriate
experience on oil tankers, have
participated in at least two COW
programmes and be fully
knowledgeable of the contents of
the Operations and Equipment
Manual.

111. As per MARPOL, Oil Record Book Part II, Cargo/Ballast Operations, must be carried
and completed on oil tankers of:
150 gross tonnes and above.
112. As per MARPOL, the contents of lines and pumps on an oil tanker at completion of
discharge must be:
Discharged ashore or retained on
board as per the pre-discharge agreement made between the ship and shore.

113. As per requirements of the International Convention for the Control and Management
of Ship's Ballast Water and Sediments, oil tankers must have a plan on board to achieve:
95% volumetric exchange of the
ballast taken on-board at the
previous port.

114. As per the OCIMF Ship to Ship Transfer Guide (Petroleum) guidelines, both vessels
engaged in the cargo transfer operation shall:
Have their main engines ready and available for immediate use
115. As per the US Code of Federal Regulations, the current Oil Transfer Procedures for a
vessel carrying out discharge in US ports must be:
Available on board, legibly printed
in a language or languages easily
understood by personnel engaged in
the transfer operation and
permanently posted or available at a
place where crew members can see
and use them.

116. Crude Oils required by MARPOL to be specifically listed in a tanker's Crude Oil
Washing manual as unsuitable for COW are:
Those with high pour point or viscosity.
117. Depending on density or API, an error measurement of 0.1 degree Fahrenheit in a tank
containing 50,000 cubic metres (314,491 barrels) of oil will result in which of the
following volumes?
25 cubic metres (157 barrels).
118. For a vessel proceeding enroute, located more than 50 nm from nearest land outside a
special area and having in operation its ODME, the maximum instantaneous rate of oil
discharge (from washings of cargo tanks) in to the sea is:
30 litres per nautical mile.

119. On board an oil tanker, slop tanks may be used for the carriage of oil:
Only on clean ballast tankers and are
only included in the total cargo
capacity of this type of vessel.
120. Prior to discharging cargo from an oil tanker, ‗line displacement‘ or ‗line pressing‘
must be conducted to ensure:
Testing of the automatic shut-down
arrangements in the shore line system.

121. The details of an internal transfer of oil must be entered in the Oil Record
Only if required by the specific
instructions of the owners or Flag
State of the vessel

122. The ideal maximum viscosity at which aromatic crude oil cargoes are best discharged
at, is:
250 cst (250 mm2/s)

123. The maximum permitted oxygen content in the inert gas main when inerting a cargo
oil tank prior to gas freeing is
5% by volume.
124. The ODME printouts for tank cleaning operations must be retained on board for a
minimum period:
Of 3 years.

125. The recommended guideline for avoiding the risk of electrostatic potential in a mist
produced by using oil and water during Crude Oil Washing operations is that:
Before washing begins, any tank
that is to be used as a source of oil
for Crude Oil Washing should be
partly discharged to remove any
water that has settled out during the
voyage. The discharge of a layer of
at least 1 metreis necessary for this
purpose.
126. To correctly report an oil spill in US waters:

The person in charge must report the spill to the National Response Center
or, if not practicable, to the Environmental Protection Agency regional
office or local U.S. Coast Guard Marine Safety Office. This must be done
immediately that person has knowledge of the spill.
127. What do we mean with a IOPP certificate?
With IOPP certificate we mean
International Oil Pollution Prevention certificate
and the ship is classed to prevent oil pollution

128. When discharging dirty ballast from an oil tanker at a high flow rate with main cargo
pumps, the instantaneous rate of discharge of oil is calculated by formula:
Instantaneous rate of discharge
(l/nm) = oil content (ppm) x flow
rate (m3/h) / speed (knots) x 1,000

129. When internally transferring any oil cargo within the vessel, the correct procedure
would be to:
Obtain permission from the
charterers and document all
operations fully in the Oil Record
Book.

130. Within the Oil Discharge Monitoring and Control System, an ‗overboard discharge
control‘ is defined as:
A device which automatically
initiates the sequence to stop the
overboard discharge of the effluent
in alarm conditions and prevents the
discharge throughout the period the
alarm prevails.
131. A hazard is is a source of potential harm or damage or a situation with potential for
harm or damage. Risk is determined based on evaluation of two elements. Which two
elements?
The likelihood that a hazard may
occur and the consequences of the
hazardous event

132. How frequently should the PA-system (Public Address) be tested?


Every week

133. How often shall abandon ship- and fire drills take place on board passenger ships?
Weekly

134. How often shall drills for the operation of watertight doors, side scuttles, valves and
closing mechanism of scuppers, ash-chutes and rubbish chutes take place in passenger
ships?
Weekly

135. How should chemicals and harmful substances be stored on board?


In a separate locker. The locker shall be
clearly marked, locked and ventilated.

136. Personnel on board passenger vessels must undergo training courses before they can
be part of the safe manning and assigned to emergency duties on board. What is minimum
training requirement for all personnel?
Basic Safety Training Course and
Crowd & Crisis Management
Training Course

137. SOLAS regulations require surveys of ships to be carried out at certain times and at
certain intervals. Which of the following surveys apply to passenger ships only?
Periodical survey every 12 months
138. The International Convention for the
Prevention of Pollution from Ships
A. Harmful Substances in Packaged Form, Sewage, Air
139. (MARPOL) covers detailed regulations to prevent various sources of ship generated
pollution. Annex I - VI deals with regulations for the prevention/ control of pollution from:
Harmful Substances in Packaged
Form, Sewage, Air Pollution,
Garbage, Oil and Noxious Liquid
Substances in Bulk

139. What information is required on passengers prior to departure?


All persons on board shall be
counted and details of persons who
have declared a need for special
care or assistance in emergency
situations shall be recorded and
communicated to the Master

140. What is important to prepare prior to a


helicopter operation?
Make sure all loose deck equipment
at helicopter deck is stowed away
and secured.

141. What is the purpose of Material Safety Data Sheets?


To provide personnel in deck- and
engine department with procedures
for handling or working with that
substance in a safe manner

142. What necessary precautions should be taken before entering a tank or an enclosed
space?
Make sure that the tank/ enclosed space is gas free, ventilated and the
oxygen content is measured.

143. Which international convention deals with maritime safety and safety equipment
onboard ro-ro passenger vessels?
SOLAS

144. Who is responsible to ensure that all personnel on board are provided with suitable
Personal Protective Equipment where it is needed?
The Company/ employer
145. You are burning garbage containing plastics. What shall you do with the ashes from
the vessel's incinerator?
Discharge the ashes to a shore facility

146. A cellular container vessel is to load frozen ice cream in containers. Space is available
either in the hold or as a deck stow. Select, from the options given, the most suitable
stowage position, with the reason, for this cargo.
The deck stow as it is less sensitive
to temperature in the event of a
mechanical problem.

147. A conventional reefer vessel operating a Controlled Atmosphere (CA) is approaching


the port of discharge in Northern Europe. Which is the most suitable action to take from
the options given?
Turn off the CA plant and thoroughly ventilate the cargo spaces under CA
with fresh air just prior to arrival.

148. A reefer vessel is loading a cargo of fruit alongside in a South African port. During
loading another vessel arrives at an adjacent berth to have its cargo discharged after having
been towed in following a fire onboard which had resulted in abandonment. What should
concern the Master of the reefer vessel most about the situation?
That the cargo may be contaminated by the smell of smoke and the products
of combustion from the damaged vessel.

149. A reefer vessel is to load a cargo of plantains and bananas. Due to space restrictions
both have to be loaded into a common space. The usual delivery temperature for bananas is
about 13 degrees Celsius and for plantains it is 7 degree Celsius. What would be the best
delivery temperature for the mixture of these two fruits?
13 C as plantains are less sensitive to the consequences of a higher delivery
temperature.

150. A reefer vessel is to load a part cargo of frozen beef hocks (large joints of beef,
usually quarters, not packed in cartons). In deciding which would be the most appropriate
space on a conventional reefer vessel, which of the given options would be the preferred
choice?
1C deck as this is the narrowest space on the vessel and will best constrain
the cargo from any possible movement during the voyage.
151. A reefer vessel, which is about to carry a palletised cargo, has to have available
sufficient cargo equipment including air bags (dunnage bags), air lines and valves, cargo
slings, wooden dunnage, nails, etc. These items are required to ensure a quick loading
operation and a successful passage. Complete the following statement from the options
given. "Air bags are particularly important in that ….
they reduce the movement of the pallets and prevent short circuiting of
the air flow."

152. A situation arises where there is insufficient fruit cargo available to fill a cargo space.
There is a cooler arrangement (cooler/evaporator/brine nest/fans) positioned at one end of
the cargo space. Select, from the options given, the best method for stowage of the fruit.
Start at the end with the cooler arrangement and work away from the cooler.

153. A situation exists where a cargo of palletised fruit is being loaded to capacity on a
conventional reefer vessel. In order to load all of the available cargo it is proposed to break
down some of the pallets and place the loose cartons on top of the pallets; there is just
enough space to accommodate this below the deckhead. From the options given which is
the most suitable action to take?
Reject the plan as the reduced gap at the top of the stow will restrict the
return air flow.

154. A standard convention for a 4 deck reefer vessel is to designate the decks A to D from
upper to lower deck. Decks A and B common as are C and D with a gas tight seal between
B and C. Apples are to be carried in decks C and D with bananas in A and B. Which of the
options is the best to avoid the risk of crossover of temperature and respiration between the
two cargoes?
Create a pressure differential with a higher pressure in decks C and D.

155. After discharge of any refrigerated cargo a thorough inspection of the vessel should be
carried out before presenting the vessel for loading the next cargo. Amongst the reasons for
this is to ensure that any traces of or residues from the previous cargo are removed. This is
particularly so if a fruit or meat cargo is to be loaded after a fish cargo has been carried.
Select, from the options given, the main reason for this requirement.
Fish is strong smelling and the odour may contaminate the next cargo.DPKP

156. Apart from temperature there are few differences between carrying cargoes of chilled
meat, minus 1 degree Celsius, and frozen meat, minus 18 degrees Celsius. A key difference
is that for frozen meat the cooling fans are operated at half speed or some are switched off
whereas for chilled meat the fans are run constantly at full speed. Select, from the options
given, the main reason for this difference in fan operation.
The chilled meat is more sensitive to damage and therefore tighter
temperature control is necessary.

157. In preparing a reefer vessel for loading the next cargo a careful inspection of the cargo
spaces should be carried out. All required maintenance and the repair of any damage
identified during the inspection should be completed prior to loading. Select, from the
options given, the most appropriate action to be taken when the maintenance and any
repairs are completed.
Make a detailed record of all maintenance and repairs carried out for
presentation to the supervisor at the loading port as proof that the vessel is
in an acceptable condition for loading the cargo.
158. On some trades fruit cargoes may be subjected to 'in-transit cold treatment' also
known as cold treatment. From the options given which is the main purpose of this cold
treatment?
To maintain a specified minimum temperature for a prescribed time period
to kill off any fruit fly which may be present when loading the cargo.

159. Reefer vessels form part of the 'cold chain' in the transport of perishable goods from
the producer to the consumer. There are times when hatches have to remain open in less
than perfect conditions, for example strong winds. There are steps that can be taken
however to mitigate the effects of this on cargo that has already been loaded. Which of the
options given could be considered to be the most important measure to counter the effect of
such conditions?

Refrain from ventilating the cargo with fresh air.

160. With the exception of some citrus fruits and bananas, fruit is usually pre-cooled to the
required carriage temperature prior to loading on a reefer vessel. In order to protect the cold
chain, and to maintain the temperature of the fruit, a minimum exposure time to ambient
conditions during loading is necessary. What action should the deck officers take during
loading to achieve this minimum exposure time?
Close the hatches and apply cooling to the cargo already loaded during any
break in cargo operations that exceed 30 minutes.
161. A Standard Ro-Ro unit weighing 18mt is to be loaded in the fore and aft direction and
lashed by belts of SWL 2mt. Using the general rule How many lashing belts should be
used to secure the unit?
9 on each side
162. A standard Ro-Ro unit weighing 2mt is to be loaded fore and aft and lashed by belts
of SWL 0.6mt. Using the general rule How many lashing belts should be used to secure the
unit?
4 on each side

163. On a roro vessel, a ro-ro unit weighing 2mt is to be loaded in the fore and aft direction
and lashed by belts of SWL 0.6mt. How many lashing belts should be used to secure the
unit?
4 on each side

164. On a roro vessel, a vehicle weighing 50mt is to be loaded in the fore and aft direction
and lashed by chains/turnbuckles of SWL 5mt. By the general Rule How many sets of
chains/turnbuckles should be used to secure the unit?
At least 10 per side
165. On a roro vessel, how often should a dangerous goods stowage plan be produced
Every time you load a dangerous cargo

166. On a roro vessel, if the vessel is loaded by stevedores, who is responsible for the
lashing of the cargo
The vessel is responsible for cargo as soon as it
crosses the ramp including its securin

167. On a roro vessel, what dangers are associated with using a steep loading ramp?
The ends of ro-ro units can be damaged

168. On a roro vessel, what instruction should be given to the crew about unlashing of
cargo prior to arrival at the berth
This can only be done when the bridge gives
permission and no unit stowed on a ramp or
incline can be unlashed. Provided the company
allow it.

169. On a roro vessel, what must be considered when planning the loading of ro-ro cargoes
on ramps?
SWL and loading limit of the ramp and
Minimum clearances for the operation of ramp
doors

170. On a roro vessel, what must be ensured onboard the vessel prior to commencing
cargo?
Cargo hold ventilation systems are
operational
171. On a roro vessel, what standing instruction should be given to prevent a blackout on
board?
Check with the duty engineer before switching
on motors, fans or other machinery
172. On a roro vessel, what standing instruction should be given to protect the Ramps
when loading ro-ro units?
Units whose weights exceed the ramp load
density/SWL must not be loaded

173. On a roro vessel, what stowage factors should be taken into account when planning
the loading of cars?
The longitudinal and athwartship distances

174. On a roro vessel, which of the following is not required in the pre-stowage plan?
Checking communications equipment
175. On a roro vessel, which of the ships trading certificates details the type and location
that dangerous goods are allowed to be stowed onboard
Certificate of compliance for the carriage of Dangerous goods

176. On a roro vessel, which of these situations will result in an emergency shutdown of
cargo operations?
Any of the listed situations

177. On a roro vessel, which regulations require supervising the embarkation of persons on
board ship?
The International Ship and Port Facility Security (ISPS)

178. Under SOLAS, what are the minimum required air changes per hour for 'Special
Category Spaces' on a roro vessel,?
10

179. What must not be obstructed when planning the loading of ro-ro cargoes?
Access to fire-fighting equipment
180. A hazard is is a source of potential harm or damage or a situation with potential for
harm or damage. Risk is determined based on evaluation of two elements. Which two
elements?
The likelihood that a hazard may occur
and the consequences of the hazardous
event
181. How can the Master ensure that all cargo loading doors, bow visors, weathertight
ramps etc. Are locked and secured before the ship proceeds on any voyage?
By having an effective system of
supervision and reporting of the
closing and opening of doors. Time
of closing and opening of doors
shall be entered in the log-book.

182. How frequently should the PA-system (Public Address) be tested?


Every week

183. How often shall abandon ship- and fire drills take place onboard ro-ro passenger
vessels?
Weeky

184. How often shall drills for the operation of watertight doors, side scuttles, valves and
closing mechanism of scuppers, ash-chutes and rubbish chutes take place in passenger
ships?
Weekly

185. How should chemicals and harmful substances be stored on board?


In a separate locker. The locker
shall be clearly marked, locked and
ventilated.
186. On most ro-ro passenger ships there is no requirement to carry out drills with the
passengers. What is the most effective ways of informing embarking passengers about the
emergency procedures?
Information on boarding cards,
public announcement on departure,
posters in public areas and cabins,
safety video running continuously
187. Personnel on board ro-ro passenger vessels must undergo training courses before they
can be part of the safe manning and assigned to emergency duties on board. What is
minimum training requirement for all personnel?
Basic Safety Training Course and
Crowd & Crisis Management
Training Course
188. The International Convention for the Prevention of Pollution from Ships (MARPOL)
covers detailed regulations to prevent various sources of ship generated pollution. Annex I
- VI deals with regulations for the prevention/ control of pollution from:
Harmful Substances in Packaged
Form, Sewage, Air Pollution,
Garbage, Oil and Noxious Liquid
Substances in BulkDPKP
189. What information is required on passengers prior to departure?
All persons on board shall be
counted and details of persons who
have declared a need for special
care or assistance in emergency
situations shall be recorded and
communicated to the Master

190. What is important to prepare prior to a helicopter operation?


Make sure all loose deck equipment at
helicopter deck is stowed away and
secured.

191. What is the purpose of Material Safety Data Sheets?


To provide all personnel including
emergency personnel with
procedures for handling or working
with that substance in a safe manner

192. What necessary precautions should be taken before entering a tank or an enclosed
space?
Make sure that the tank/ enclosed
space is gas free, ventilated and the
oxygen content is measured. O2
content shall be 21% before
entering the tank/ enclosed space

193. Which international convention deals with maritime safety and safety equipment
onboard ro-ro passenger vessels?
SOLAS

194. Who is responsible to ensure that all personnel on board are provided with suitable
Personal Protective Equipment where it is needed?
The Company/ employer

195. You are burning garbage containing plastics. What shall you do with the ashes from
the vessel's incinerator?
Discharge the ashes to a shore
facility

196. A bulk vessel loads a full cargo to summer marks of a high density bulk cargo such as
iron ore concentrate; what would be the possible stability conditions produced?

The vessel will normally have a


large intact metacentric height
(GM) and have a fast roll period

197. A cargo hatch cover seal on a Bulk Carrier is known to be damaged and not weather
tight prior to sailing; what is the legal significance of this situation?
The vessel may well be judged to be un-seaworthy; this could invalidate
some certification and hull and machinery insurance

198. Before a solid bulk cargo is loaded, the Master and shore representative must agree a
loading plan which covers which of the following aspects?
All of the items specified in the possible answers
199. How are cargoes on self-unloading bulk carriers fed to the vessel's conveyor belts
during discharge?
Via hydraulically-operated hopper
gates at the bottom of each hold

200. The high level water ingress alarm in number 1 hold of a Bulk Carrier activates in bad
weather at sea; what would be the actions of a prudent Master?
Sound general alarm, muster ships
crew and transmit a Mayday call
and message.

201. Under international regulations for a Bulk Carrier, who needs to be trained in the use
of oxygen analysis and gas detection equipment?
The ship's crew

202. What does the IMSBC Code emphasise with reference to the exposure of personal to
the dust created when carrying some bulk cargoes?
A high standard of personal hygiene

203. What extent of hatch cover spares should be available on board a Bulk Carrier at all
times?
Specimen fittings shown in the
hatch cover manufacturer's manual

204. What height of water above the inner bottom will activate the cargo hold high level
alarm on a Bulk Carrier
Any height above 2.0m

205. What is the maximum period between the sampling/testing of the moisture content of
a solid bulk cargo and the loading of that cargo into a bulk carrier?
A maximum for seven (7) days,
when there has been no change in
the moisture content due to rain or
snow

206. What must be specified when ordering gas detection equipment when used in
association with bulk carriers?
That the instrument is suited for its purpose of application

207. What specific data must be displayed on the loading instruments carried on bulk
carriers of 150m or more in length?
The shear forces exerted on the hull structure
208. Where are cargo hold water level detectors required to be fitted on bulk carriers?
At the after end of each cargo hold

209. Which of the following is a warning sign of a faulty hydraulic hatch cover system on a
Bulk Carrier?
A fall in the hydraulic header
tank level

210. Who needs to be trained in the use of oxygen analysis and gas detection equipment?
The entire ship's crew

211. Why do bulk cargo carriers need to carry oxygen analysis and gas detection
equipment?
Because of enclosed or confined space entry
requirements
212. Why do the cargo holds of a self-unloading bulk carrier have a "W" shaped cross
section?
So that during discharge the cargo
will automatically fall onto the
underlying conveyor belts

213. A vessel has lost several containers overboard during a voyage. Upon arrival into
port, she is being inspected by the attending surveyors. The most important item to
be checked during this inspection would be:
Certificates of approval related to lashing equipment used to secure those
containers.

214. An inspection in the amidships area of the weather deck of a Panamax container
vessel has revealed cracks in the hatch coamings. It is extremely important to
urgently inspect the:
Longitudinals in the double bottom tanks in the amidships half length of the
vessel.

215. For a ships loading computer to be safely used for loading planning and stress
calculations, it must be approved by:
A Classification Society.

216. On a container vessel, flexitanks are used for:


The carriage of non-hazardous liquids, in bulk.
217. Racking forces imposed on a container would likely cause the greatest deflection to:
The door end of the container.

218. Shock loads in a container lashing system are generally caused by:
Loose cargo lashings.

219. The correct weight of a wrongly declared container may be best indicated by:
Strain gauges fitted to the
shore gantry cranes.DPKP

220. The most appropriate way of dealing with twist-locks suffering from excessive wear
and tear is to:
Isolate them from use and dispose them appropriately.

221. The most dangerous consequence of the corrosion and wear down of container
stools on weather deck/hatch tops of a container vessel would be:
Collapse of the deck stool, leading to lashings becoming slack.

222. The most effective method of dealing with an under-deck cargo space fire on board
a container ship, is to:
Deploy the fixed firefighting system.

223. The most important function of a buttress fitting on a container vessel is: To
transfer forces from the container stow to the ships structure.
224. What contributes to wear-down of twistlocks on a container vessel?
The continuous action of longitudinal forces.
225. What items of container securing equipment must be used in conjunction with
buttresses?
Double stacking cones or link plates.

226. When planning the loading of containers, the planning officer must refer to:
The Cargo Securing Manual (CSM).
227. "Passivation" is a restorative process periodically applied to stainless steel tanks on
a chemical tanker. What effect does this process have on the steel surface?
It restores and reforms the passive
Chromium Hydroxide surface layer.

228. A cargopumproom or other enclosed space which contains cargo handling


equipment on a chemical tanker shall be fitted with a mechanical ventilation
system, capable of being controlled from outside the space. What is the minimum
number of atmosphere changes per hour, based on the total volume of the space,
that such a system must deliver?
Not less than 30 changes per hour
.

229. Basic manual dew point measurement devices are commonly used by surveyors
when monitoring the dryness of a cargo tank prior to loading a liquid chemical
product. Which of the descriptions below is a summary of how the measurement is
carried out?
A small quantity of Acetone is placed into the device and dry-ice is
progressively added to it to steadily reduce the temperature. A sample of the
atmosphere in the tank is continuously drawn through the device, passing
over the polished or mirrored surface of the container. When the first drop
of mositure (dew) is observed to form on the polished surface, the
temperature of the Acetone bath is noted. Reference may be required to
tables to correct the reading for desired parameters.

230. Chemical tankers of 20,000 tonnes DWT or above, with a keel laid on or after 1st
July 1986, when carrying flammable products with a flashpoint not exceeding 60
degrees Celsius, such as those listed in chapters 17 and 18 of the International Bulk
Chemical Code, are exempt from the requirement to be fitted with and use an inert
gas plant provided certain conditions are met. Which of the following is a summary
of those conditions?
The cargo tank does not exceed 3000 cubic metres capacity / each tank
washing machine nozzle does not exceed 17.5 cubic metres per hour
delivery rate / the total wash water input to the tank from all tank washing
machines does not exceed 110 cubic metres per hour.
231. High level and high-high level alarms must be tested at the tank for proper operation
within 24 hours of the start of cargo transfer on a chemical tanker. What acceptable
alternative is there to this requirement?
That a function test is carried out by means of an automatic self-test and
circuit monitoring facility within the alarm system.

232. How would you determine whether a particular cargo transfer hose was compatible
with the chemical product to be transferred?
Refer to the product entry in the hose manufacturer's chemical resistance
chart.
233. If your chemical tanker is equipped with high velocity venting valves, at what
minimum height above the weather deck or catwalk should they be installed?
3 metres

234. In a typical shipboard de-humidifier plant as may be found on a modern chemical


tanker, operating on a "rotating bed" principle, what names are given to the two
parts of the rotating bed?
The "process sector" and the "reactivation sector".
DPKP

235. The IBC Code prescribes certain design conditions for a cargo heating or cooling
system fitted to a chemical tanker. What does it require in respect of pressure
within such a system, for any condition other than when it is empty?
That a higher pressure can be maintained within the system than the
maximum pressure head that could be exerted by the contents of the cargo
tank on that system.

236. The specified maximum working pressure of a cargo hose in service on a chemical
tanker should be at least which of the following?
10 bar gauge.

237. To what pressure will a new length of cargo hose be tested by a manufacturer prior
to its supply to a vessel for service onboard a chemical tanker?
Not less than one and a half times its specified maximum working pressure,
but not more than two-fifths of its bursting pressure.

238. What temperature defines "hot" water in the context of tank washing on a chemical
tanker?
At least 60 degrees Celsius.

239. When a submerged centrifugal cargo pump is being run at too high a speed during
discharge of a viscous chemical cargo, the pump may start racing, causing a heat
build-up around the suction, possible localised solidification of the cargo and
consequent damage to the pump. What term is applied to this problem?
Cavitation.

240. Which of the following is a summary of the features of a "controlled tank venting
system" as may be found on a chemical tanker?
PV valves are fitted to limit the pressure or vacuum in the tank; no shut-off
valves may be fitted either above or below the PV valves; provision may be
made to by-pass the PV valves under certain operating conditions; such a
system shall consist of a primary and secondary means of allowing full flow
of vapour, except that the secondary system may be replaced by pressure
sensors fitted within the tank.

241. You are carrying a bulk cargo of Phosphoric Acid. Which components of the cargo
pumps may be damaged as a result of discharging this particular cargo and why?
The cargo seals may be damaged from the abbrasive effect of any sediment.
The outer casing may be corroded by the unstable impurities within the
acid.

242. A five yearly thorough survey of cargo gear on a General Cargo vessel should be
carried out by:
A classification society surveyor.
243. A General Cargo vessel has a 50 tonne SWL heavy lift derrick and a load of 48
tonnes is to be loaded. The lifting gear of slings and spreader bar weighs 4 tonnes.
In this case, it would be correct to state that:
The load cannot be loaded because the combined weight of the load and the
lifting gear will exceed the SWL by two tonnes.
244. During a pre-loading survey on board a General Cargo ship, the most efficient
method of testing the weather tightness of the hatch covers is considered to be:
Ultra sonic test.
245. During cargo watch on a General Cargo ship, if the OOW informs you that the
condition of the discharge equipment such as slings and shackles being used by the
stevedores is unsuitable for use, you should:
Inform stevedores of concern and protest by letter.
246. Information about the maximum point loading in cargo holds and on decks of a
General Cargo Vessel may be obtained from:
Ships Capacity plan.

247.. On a general cargo ship, operating the heavy lift derricks with the boom close to
horizontal could result in:
Excessive stresses acting on parts of the derrick system.

248. On a General Cargo ship, the most likely cause of a hatch cover hydraulic system to
deteriorate would be:
Due to dust and cargo particles lodged around the piston seals.

249. On a General Cargo vessel, a 16T derrick should be tested to a proof load of:
20T
250. Prior to loading cotton on a General Cargo vessel, it is important to ensure that:
The cargo hold fire-fighting system is thoroughly examined.

251. Prior to loading general cargo on a General Cargo vessel, with regard to lashing
wires, terminations, shackles, turnbuckles, pad eyes and D rings etc., you must
make sure that:
They must all be certified and be visually inspected for any apparent
damage.

252. Proper guidance on the stowage and securing of general cargo may be obtained by
referring to:
IMO Code of practice for stowage and securing of cargoes.

253. The lifting plant on a General Cargo vessel be proof load tested:
When equipment is new, every five years and after repairs or major
modifications.
254. The main purpose of a hatch cover ventilator grill on a General Cargo vessel is:
To prevent sparks entering the cargo hold.

255. The ship‘s lifting plant must be proof load tested and all parts thoroughly examined
at intervals not exceeding:
5 years

256. When general cargo is damaged during heavy weather on a General Cargo vessel, it
must be ensured that the damage is inspected by the:
Surveyor representing the vessel's P. & I. Club.

257. According to "Summary of minimum requirements" in the IGC Code, what is the
requirement for vapour detection for methane (LNG) cargoes?
Flammable vapour detection.
258. According to the IMO Gas Code, what is the requirement for the number of sets of
portable gas detection equipment that must be carried onboard an LNG carrier?
There must be at least two sets.

259. According to the IMO Gas Codes, what are the maximum time intervals for
sampling and analysing samples from the permanent installed gas detection system
on a LNG carrier?
96. A 30 minutes.
260. According to the IMO Gas Codes, what is the required number of temperature
indicating devices in the cargo tanks of an LNG carrier?
At least two devices in each tank.

261. Gas carrier type A and B cargo tanks have a MARVS of less than 0.7 barg? What is
the liquid and vapour connection shut off valve requirement for this type of tank
according to the IMO gas codes?
Single shut-off valves with manual closing
facility.

262. LNG tankers are often fitted with fixed water spray system for fire protection
purposes for deck areas, deck tanks, deck manifolds and pipelines. What is the
minimum required flow rate of water per minute for horizontal and vertical surfaces
to ensure adequate, uniform coverage of these areas?
10 litre/m2 per minute for horizontal surfaces
and 4 litre/m2 per minute for vertical
surfaces.

263. Select, from the options given, the one that best describes a requirement of the
remotely controlled valves fitted in the ESD (Emergency Shut-Down) systems on
an LNG carrier?
They must be fail-safe.

264. Some LNG carriers are fitted with a water glycol system for heating the cofferdam
spaces next to cargo tanks when the vessel is loaded. What is the purpose of this
heating system?
To maintain the temperature inside the space above 5
degrees C to protect the steel.

265. What is the minimum requirement with respect to pressure relief valves on the cargo
tanks of an LNG carrier where the individual tanks are over 20 cubic metres
capacity?
Two valves.
266. What is the preferred method of accommodating expansion in cargo pipeline
systems on LNG carriers?
Use expansion loops.

267. What is the purpose of the "forcing vaporizer" found in some LNG carrier cargo
plants?
To provide gas for burning in the boiler.
268. When LNG is used as fuel a double wall piping system must be used in the engine
room. What condition should the annular space between the concentric pipes be
maintained in when the fuel system is in service?
Filled with nitrogen at a pressure greater than the LNG fuel
pressure.

269. Which kind of cargo pumps are the most commonly used in cargo systems for LNG
carriers?
Submerged electric motor pumps.

270. Which line can be utilized to prevent line surge when starting the main pumps of a
LNG carrier's cargo system?
The condensate spray line.

271. Which of the following insulation materials that are used in the cargo containment
systems for LNG carriers has the highest diffusion resistance?
Polyurethane foam.

272. A chlorine carrier must be equipped with a chlorine absorption plant connected to
the cargo tanks and cargo lines. This requirement includes the provision of gas
detectors for the spaces and areas around the cargo containment system and the
absorption plant outlet. What is the recommended setting for the visual and audible
alarms of the gas detectors?
97. 5 ppm.
273. Cargo heaters are frequently used when discharging refrigerated LPG cargoes into
pressurised shore tanks. What would be a typical "heating range" required from a
heater for discharge of fully refrigerated propane?
From - 45 C to - 5 C.

274. Cargo hoses intended for liquefied gas carriers have to be prototyped tested before
being approved. When new hoses of an already approved type are received onboard
they also need to be pressure tested before being put into service. What are the IMO
Gas Code requirements for such hoses before they are put into service?
Not less than 1.5 times the specified
maximum working pressure or
more than two fifths of bursting
pressure at ambient temperature.
275. LPG carriers rely heavily on the compressors fitted as part of the reliquefaction
plant. Screw and reciprocating types are widely used. Which type of reciprocating
compressor is most common as a cargo compressor?
Double acting, single stage, oil free
compressor.

276. Most reliquefaction plants on LPG carriers use a direct cooling system. Which of the
statements given in the options best describes a direct cooling cycle?
Cargo vapours are drawn off by a compressor, compressed, condensed than
passed through an expansion valve back to the tank.

277. Some liquefied gas carriers are fitted with nitrogen generating equipment, often of
the membrane module design. What would be the expected purity of the nitrogen
produced by such equipment?
95 to 97% pure nitrogen.

278. The IMO Gas Codes require that all liquefied gas carrier cargo tanks are fitted with
pressure relief valves. Pilot operated relief valves are frequently used, particularly
with refrigerated cargoes. What is the main advantage of using pilot operated relief
valves rather than simple spring loaded types for refrigerated liquefied gas cargoes
tanks?
They ensure accurate operation at the very low cargo carriage pressures.

279. The reliquefaction plant for cargo cooling of liquefied gas cargoes can operate on
either a direct or indirect cycle. On which liquefied gas cargoes must indirect cycle
cargo cooling plant be used according to the IMO Gas Codes?
Cargoes such as chlorine, ethylene oxide and propylene oxide for which the
vapours cannot be compressed due to temperature restrictions.
280. There are a number of standard reliquefaction plants commonly fitted onboard LPG
and other liquefied gas carriers. What type of reliquefaction plant is required for a
cargo of Ethylene Oxide?
Indirect cycle.

281. There are strict rules governing the placement and category of electrical equipment
allowed in certain areas of liquefied gas carriers. One such category is that of
flameproof enclosures. What is a flameproof enclosure?
One which can withstand the pressure build-up during an internal ignition of
a flammable mixture and is designed to cool any flames occurring within
the enclosure to below the ignition temperature.

282. What is the main disadvantage of using oil free, screw type compressors for the
reliquefaction plant of an LPG carrier?
The compressor has to run at very high speeds to compensate for internal
leakage.
283. Whatis the purpose of an automatic shut-down system fitted onboard most liquefied
gas carriers and how is it initiated?
To prevent overfilling of the cargo tanks. It is initiated by a high level
sensor in the cargo tank.

282. What is the purpose of the purge gas condenser fitted to some liquefied gas carrier
reliquefaction plants?
It is used to condense out any cargo vapours which have passed through the
main condenser with incondensable gases.
283. When measuring the liquid level in the cargo tank of a liquefied gas carrier a number
of different corrections may be necessary to get a true reading. Why do readings
obtained from a float type ullage tape sometimes require a 'tape correction'?
The length of tape in contact with very cold cargo vapours may contract

284. Which type of reliquefaction plant can have the cooling coil placed directly in the
vapour space of the cargo tank?
One type of the indirect cycle reliquefaction plants.
285. A ―Pellistor‖ is:
It is an electrical sensor unit fitted
in a flammable gas detector for
measuring hydrocarbon vapours and
air mixtures to determine whether
the mixture is within the flammable
range

286. According to 33 CFR 156, for oil tankers trading in US waters, the minimum
requirement for testing of cargo transfer hoses and associated piping system are:
That no leakage occurs under static
liquid pressure of at least 1.5 times the
maximum allowable working pressure.
287. After passing through the scrubbing tower of an inert gas system, the approximate
level of carbon dioxide in the inert flue gas should be:
13%
288. An oil tanker with a defective Oil Discharge Monitoring Equipment may be allowed
by a Port State Authority to trade for:
One ballast voyage before
proceeding to a repair port.

289. An oil tanker's tank-cleaning machine with a rotational speed of 1 rpm and a
selected pitch angle of 1.5 degrees is used to perform a bottom wash with a vertical
angle from 40 degrees to 0 degrees for 1.5 cycles (3 passes). If the throughput of
the machine at design pressure is 90 m3/hr, what will be the washing time and
quantity of crude oil required?
40 minutes and 60 cubic metres of oil.

290. As per IMO requirements, the mechanical ventilation system of the cargo pump
room shall be capable of making:

At least 30 air changes per hour

291. As per OPA 90 requirements, a vessel over 400 feet (121.9 metres) in length must
carry oil spill clean-up gear to be able to handle oil spillages of:
98. barrels (1.91 cubic metres).

292. Fluid driven eductors operate on Bernoulli‘s principle, which states that:
The speed of a moving fluid increases
as the pressure in the fluid decreases.

293. Ship‘s cargo pump room alarm must be automatically activated when levels of
hydrocarbon gas concentration are:
No higher than 10% of LEL.
294. The automatic stripping systems fitted on some of the centrifugal cargo pumps
operate on the principle that:
If cargo vapour can be stopped from
entering the cargo pump suction
inlet, the flow will continue without
cavitation.

295. The calibration of the ODME is carried with the use of:
Fresh water.

296. The difference between the absolute pressure of a liquid at the inlet to a cargo pump
and the vapour pressure of the liquid is called the:
Net Positive Suction Head Available.

297. The inert gas system shall be capable of delivering inert gas to the cargo tanks at the
rate of:
At least 125% of the maximum discharge capacity.

298. The typical amounts of sulphur dioxide gas in flue gas produced when burning high
sulphur content fuels would be:
2,000 ppm

299. The usual pressure and vacuum levels at which the P/V valves on board an oil tanker
are required to activate are:
Pressure: 1 psi (0.069 bar) Vacuum: 0.5 psi (0.034 bar)
300. When in-service testing a hose used for cargo transfer on an oil tanker (and for
which the elongation of the hose assembly when new was greater than 2.5%), the
maximum permitted elongation before the hose must be withdrawn from service
should be:
Not more than 1.5 times the
temporary elongation measured
when the hose assembly was new,
as documented in the
manufacturer's certificate.

301. When tank cleaning hoses are tested for electrical continuity, they must display a
reading of:
Not greater than 6 ohms per metre length.

302. A decision support system for emergency management shall be provided on the
navigation bridge. What type of emergency situations shall as a minimum be
identified in the emergency plans?
Fire, Damage to ship, Pollution,
Unlawful acts threatening the safety
of the ship and the security of its
passenger and crew, Pesonnel
accidents, Cargo-related accidents,
Emergency assistance
to other ships

303. Emergency instructions in appropriate languages shall be posted in passenger cabins.


Which information shall as a minimum be included in the emergency instructions?
The method of donning life-jackets, escape
routes and alarm signals

304. Here do you find detailed information and specific technical requirements for life-
saving appliances?
Life-Saving Apliance Code (LSA Code)

305. How many lifejackets are required in a passenger cabin?


Same number as beds in the cabin

306. How many rescue boats should be provided on passenger ships of 500 gross tons
and above?
Two, one on each side of the ship

307. How many two-way VHF radiotelephone apparatus shall be provided on board a
passenger ship of 500 gross tonnage and upwards?
3
308. Is it required that the PA-system (Public Address) is connected to a back-up power
sypply?
Yes, the public address system shall
be connected to the emergency
source of power
309. Is it required to have supplementary emergency lighting on board passenger ships?
Yes, all passenger public spaces and
alleyways shall be provided with
supplementary electric lighting
310. One water fog applicator is required for each pair of breathing apparatus on
board which type of ship?
Passenger ships carrying more than 36 passengers

311. Passenger ships have a normal requirement of 1 lifejacket per person + 10%
for children. In addition to this, how many lifejackets have to be stowed in
conspicuous places on deck or at the muster stations?
5% extra

312. Passenger ships shall either carry automatically self-righting liferafts or


canopied reversible liferafts. What does it mean that a liferaft is
automatically self-righting?
The liferaft will automatically turn
back into an upright position when
it is empty of people
313. What is the minimum number of independently driven fire pumps that must
be provided on passenger ships of 4000 tons gross tonnage and upwards?
3
314. What is the minimum number of lifebuoys that shall be provided with self-
igniting lights an self-activating smoke signals?
2
315What is the name of this unit?
A hydrostatic release unit

316. What is the purpose of an evacuation


analysis?
To identify and eliminate, as
far as practicable, congestion
which may develop during an
abandonment

317. What is the time limit for abandonment of passenger ships?


30 minutes from the time the
abandon ship signal is give
318. Where do you find detailed information and specific technical requirements
for fire safety systems?
Fire Safety Systems Code (FSS Code)
319. Where shall you be able to activate the ship security alert system on board
passenger ships?
From the navigation bridge and in at least one
other location

320. Which one of the listed requirements for passenger ships regarding personal
life-saving appliances do not correspond to present regulations?
All lifejackets shall be fitted with a whistle, a
light and a smoke signal

321. As part of the decommissioning process for old reefer vessels they are sent to
a recycling yard where any refrigerant remaining in the refrigeration system
is dealt with. Which one of the actions given in the options needs to be
carried out in preparation for delivery of a vessel to a recycling yard?
Make a careful note of the
quantities of gas onboard and note
this in the Ozone depletionrecord
Book prior to discharging the gas
into recovery bottles.

322. As well as having temperature sensors located in the cargo holds some reefer
vessels are also fitted with ethylene sensors. Why is it useful to have
information regarding the ethylene content in a reefer vessel cargo hold
when carrying fruit cargoes?
Some fruit cargoes are sensitive to ethylene and the quality of the
cargo can deteriorate as they may over-ripen.
323. Data loggers are a vital part of the temperature control and monitoring system
on a reefer vessel. In a situation where the data logger fails several days
before the end of the voyage it is still necessary to maintain control of and
monitor cargo temperatures. How could an accurate, portable thermometer
be used to the best effect, to achieve this, in such a situation?
Use the thermometer to check and control the delivery air
temperature by inserting it in the delivery air ducting close to the
evaporators.
324. Despitesetting what appears to be the correct delivery air temperatures in
accordance with shipper's instructions, large cargo loss claims can still occur
when operating reefer vessels. Which of the options given is likely to help
avoid the majority of these large claims?
By confirming the temperature scale that the shipper is using in his
carriage instructions, Fahrenheit or Celsius.
325. Many fruit cargoes are carried refrigerated and also under controlled
atmosphere (CA) conditions. A situation develops where there is a problem
with the main reefer plant that will take several hours to repair but the CA
system is still operation. Which of the statements given in the options is the
most accurate in these circumstances?
The CA plant is only an adjunct for the refrigeration plant and
therefore there should be concern about the condition of the cargo.

326. Many reefer vessels are fitted with controlled atmosphere systems (CA).
There are a number of different systems available but generally they all
work by introducing nitrogen into the cargo space. Select, from the options
given, the main reason why nitrogen is generally the gas chosen for
controlling the atmosphere in the cargo spaces of a reefer vessel.
Nitrogen displaces the oxygen in the cargo space and allows the
respiration of the fruit to be controlled.
327. Most fruit cargoes carried under refrigeration require introduction of fresh air
into the cargo space to remove any excess carbon dioxide and ethylene
produced by respiration of the cargo and sensors are fitted to detect these
gases. Shipper's instructions will often indicate 'constant air change' as a
requirement for a cargo. Why, even though this is a crude method for
controlling the cargo space atmosphere, is this type of instruction given?
Some cargoes are very sensitive to ethylene levels and it may be
difficult to accurately measure the low levels that would affect a
cargo.
328. On a conventional reefer vessel is possible to ventilate the cargo spaces with
fresh air using fans and trunkings. One of the reasons for using fresh air
ventilation is to control the relative humidity within the cargo space. Select
the option which best completes the following statement. "It is beneficial to
be able to control the relative humidity within the cargo space because fruit
cargoes should be kept…
…relatively moist to avoid the cargo dehydrating during the passage."

329. On a reefer vessel air is passed over the cooling coils before entering the
cargo hatch via trunking to cool the cargo. It is important to ensure that the
cooling coils are clear of any material such as plastic sheeting or bags. Why
is this so important?
The plastic may interfere with the air flow over the cooling coils and
subsequently the cooling of the cargo.

330. Prior to loading a reefer cargo it is good practise to carry out an 'ice test' of
the temperature sensors within the cargo space. Part of the test is to immerse
the sensors in a test bucket of known temperature, usually zero degrees
Celsius as this is the melting point of ice. Which of the options is correct in
relation to preparing the test bucket?
Insulated ice buckets should be filled with ice cubes approximately 2
centimetres square and a small quantity of distilled water to produce
an ice-water mixture. The ice cubes should be produced from clean
distilled water. Insulated ice buckets should be filled with ice cubes
approximately 2 centimetres square which have been made from
clean distilled water.
331. Refrigerated cargo spaces are fitted with temperature sensors and in some
cases carbon dioxide sensors. From the options given select the one which
best completes the following statement. "Monitoring the carbon dioxide
content in a cargo space loaded with fruit can be useful because…
increasing levels indicate that the fruit may be starting to ripen."
its presence indicates that the fruit is ripe."
low levels indicate that there are insufficient numbers of air changes."
its presence indicates that the fruit is still not ripe."

332. Selectthe option which correctly completes the following statement. "A
conventional reefer vessel operating with a controlled atmosphere plant must
have cargo spaces which…

have the normal bulkhead and deckhead penetrations required for


a reefer compartment."

333. The data logger on a reefer vessel normally records temperatures for air
delivery, air return and cargo pulp. How would the air delivery and return
temperatures be expected to vary during the first few days of carrying a
cargo of citrus fruit which had not been pre-cooled before loading?
The difference between the two temperatures would steadily reduce.
334. To correctly interpret the readings on the printout from a reefer vessel‘s cargo
data logger it is essential to have some knowledge of the location of the
temperature sensors. Where would the temperature sensor for the delivery
air to a cargo hold be expected to be located?
In the air flow path from the cooling coils, about 3 metres from the coils.

335. What should be done with the data logger printouts after completing the
discharge of a refrigerated cargo?
They should be retained onboard for a minimum of 2 years.
336. During sea passage on a roro vessel, how would you know if gasoline
vapours were escaping from vehicles?
By using flammable gas detectors in the vehic

337. On a roro vessel, to what should you pay very close attention, when
inspecting the structure and condition of movable car decks?
Cracks in way of deck support

338. On a roro vessel, what additional securing arrangements should be used when
loading a vehicle on an incline or fixed Ramp
339. On a roro vessel, what is Maximum Securing Load?
The load capacity of a device used to secure cargo on board

340. On a roro vessel, what is the Maximum Securing Load of 'D' rings?
50% of the breaking strength

341. On a roro vessel, what is the Maximum Securing Load of fibre ropes?
33% of the breaking strength

342. On a roro vessel, what is the Maximum Securing Load of mild steel shackles?
50% of the breaking strength

343. On a roro vessel, what is the Maximum Securing Load of reusable use wire ropes?
30% of the breaking strength

344. On a roro vessel, what is the Maximum Securing Load of single use wire ropes?
80% of the breaking strength
345. On a roro vessel, what is the Maximum Securing Load of web lashings?
50% of the breaking strength
346. On a roro vessel, when should a trailer horse be taken out of service
If there is any damage to the wheel or spring, the frame is rusted or
distorted or the pads are worn out

347. On a roro vessel, where can you find the validity of web
lashings
On the certificate supplied with the equipment
348. On a roro vessel, where will escaping gasoline vapourssettle in a cargo hold?
If the forced ventilation system is shut down
At the lowest levels

349. What must you ensure when using portable slopes to discharge ro-ro
units?
They must be exactly aligned with the units' tyres
350. When lowering a roro Cargo Side or Stern Ramp what must be ensured ?
The vessel is securely moored and
there is nothing beneath the ramp
351. A decision support system for emergency management shall be provided on
the navigation bridge. What type of emergency situations shall as a
minimum be identified in the emergency plans?
Fire, Damage to ship, Pollution,
Unlawful acts threatening the safety
of the ship and the security of its
passenger and crew, Pesonnel
accidents, Cargo-related accidents,
Emergency assistance to other ships

352. Emergency instructions in appropriate languages shall be posted in passenger


cabins. Which information shall as a minimum be included in the emergency
instructions?
The method of donning life-jackets, escape routes and alarm signals

353. How many lifejackets are required in a passenger cabin?


Same number as beds in the cabin

354. How many rescue boats should be provided on ro-ro passenger ships of 500
gross tons and above?
Two, and at least one of the rescue
boats shall be a Fast Rescue Boat

355. How many two-way VHF radiotelephone apparatus shall be provided on


board a ro-ro passenger ship of 500 gross tonnage and
upwards?
3

356. Is it required that the PA-system (Public Address) is connected to a back-up


power sypply?
Yes, the public address system shall
be connected to the emergency
source of power
357. Is it required to have supplementary emergency lighting on board ro-ro
ships?
Yes, all passenger public spaces and
alleyways shall be provided with
supplementary electric lighting
358. Passenger ships have a normal requirement of 1 lifejacket per person + 10%
for children. In addition to this, how many lifejackets have to be stowed in
conspicuous places on deck or at the muster stations?
5% extra
359. Ro-ro passenger ships shall either carry automatically self-righting liferafts or
canopied reversible liferafts. What does it mean that a liferaft is
automatically self-righting?
The liferaft will automatically turn
back into an upright position when
it is empty of people

360. What is the minimum number of independently driven fire pumps that must
be provided on passenger ships of 4000 tons gross tonnage and upwards?
3
361. What is the minimum number of lifebuoys that shall be provided with self-
igniting lights an self-activating smoke signals?
2
362. What is the purpose of an evacuation analysis?
To identify and eliminate, as far as practicable,
congestion which may develop during an
abandonment
363. What is the time limit for abandonment of ro-ro passenger
ships?
30 minutes from the time the abandon ship signal
is given
364. What is this?

A hydrostatic release unit


365. Where do you find detailed information and specific technical requirements
for fire safety systems?
Fire Safety Systems Code (FSS Code)
366. Where do you find detailed information and specific technical requirements for life-saving
appliances?
Life-Saving Apliance Code (LSA Code)

367. Where shall you be able to activate the ship security alert system on board ro- ro passenger
ships?
From the navigation bridge and in at least one other location

368. Which one of the listed requirements for passenger ships regarding personal life-saving
appliances do not correspond to present regulations?
All lifejackets shall be fitted with a whistle, a
light and a smoke signal

PLAN AND ENSURE SAFE LOADING

1. Your draft are : FWD 5’-08”, AFT 6’-02. From past experience, you know that the vessel will
increase her draft 1 inch for every 8 tons loaded. There is rig water on board and 11 tons of deck
cargo. How many more tons of cargo can be loaded and still maintain the same trim ?
24 tons

2. Which operation may cause the pressure in an inert tank to fall below the prescribed limits ?
Discharging

3. When loading a bulk cargo of cement the specific gravity and flow characteristics are dependant on
what criteria ?
The volume of air in the cargo

4. Your draft are : FWD 6’-01”, AFT 6’-05. From past experience, you know that the vessel will
increase her draft 1 inch for every 7 tons loaded. There is rig water on board and 20 tons of deck
cargo. How many more tons of cargo can be loaded and still maintain the same trim ?
14.0 tons

Plan and ensure…….

1. What are the advantages of ballasting double bottom ballast tanks by gravity filling
on a Bulk Carrier?
There is minimum pressure head on the tank top and pumps are not
required

2. During a loaded winter passage across the North Atlantic, the master of a container
vessel would be most concerned with:
The added weight of icing on container stacks, leading to loss of GM.
3. The Code of Safe Practice for Cargo Stowage and Securing was prepared to give
guidance for:
Preparation and content of the Cargo Securing Manual.

4. Which of these covers the rules and regulations for General Average on a Bulk
Carrier?
The York Antwerp rules

5. What is essential to ensure that efficient stripping of ballast tanks on a Bulk Carrier
can be achieved?
A good stern trim is maintained during de- ballasting operations

6. A bulk cargo vessel is found to be 4.0 centimetres over her maximum loadline draft
after loading; what should be the actions of the master?
Order the pumping out of fresh water or ballast until the maximum
allowed loadline is achieved.

7. A bulk carrier is to carry a full deck cargo of packaged timber; to what regulations
must the vessel comply?
IMO Code of Practice for the carriage of Timber Deck cargoes

8. Why do structural steel products often shift or collapse in a bulk carrier's cargo
holds?
Because the irregular shape of the cargo holds results in void spaces

9. A heavy piece of machinery is loaded on deck of a container vessel, stowed across


several flat rack containers. The most appropriate method for lashing such cargo
would be by:
Taking all lashings to the flat-rack lashing points.

10. During a loaded winter passage across the North Atlantic, the master of a
container vessel would be most concerned with:
Metacentric height of the vessel.

11. For guidance on lashing arrangement of containers on-board the vessel, the most
important document to refer is:
The Cargo Securing Manual.

784. A bulk cargo is loaded and the cargo stow has been left with an excessive peak height; what could be the
result of this situation?

Excessive stresses on tank top

785. A bulk cargo vessel is found to be 4.0 centimetres over her maximum loadline draft after loading; what should
be the actions of the master?

Order the pumping out of fresh water or ballast until the maximum allowed loadline is achieved.

786. A bulk carrier is to carry a full deck cargo of packaged timber; to what regulations must the vessel comply?
IMO Code of Practice for the carriage of Timber Deck cargoes

787. During a pre-loading survey prior to loading grain on a Bulk Carrier, very small

amount of the previous grain cargo is found in a cargo hold; what is the

significance of this situation?

The vessel may fail the pre-load survey and be declared off-hire

788. How should mild steel slabs be loaded in a bulk carrier?

Interlocked across the entire cargo hold with the longitudinal axes athwartships

789. What are the advantages of ballasting double bottom ballast tanks by gravity filling on a Bulk Carrier?

There is minimum pressure head on the tank top and pumps are not required

790. What could happen if a bulk vessel failed to display placards notifying the crew of the disposal of garbage
within and outside Special Areas?

The vessel could be detained by port state control authorities

791. What governs the disposal of dry bulk cargo residues at sea?

MARPOL regulations

792. What is essential to ensure that efficient stripping of ballast tanks on a Bulk Carrier can be achieved?

A good stern trim is maintained during de- ballasting operations

793. What is the possible concern if fuel tanks on a Bulk Carrier, which are close to cargo spaces containing grain,
are excessively heated?

The grain cargo may be heated and damaged

794. What is the purpose of a draught survey before and after loading on a Bulk Carrier?

To ascertain the actual weight of cargo loaded

795. What measures should be taken in order to avoid flammable gases forming on top of coal cargoes on a Bulk
Carrier?

Ventilation to be carried out as indicated in the IMO solid Bulk Cargo Code

796. What must be ensured, prior to receiving a bulk cargo of iron ore on a Bulk Carrier?

Cargo hold bilge suctions must be satisfactorily tested

797. What publication must be carried on a vessel carrying dry bulk cargoes?

IMO Solid Bulk cargo Code or IMO Solid Bulk?

798. When considering how to deal with cargo residues during hatch cleaning at sea on a Bulk Carrier, what is the
most careful consideration?

Consult MARPOL handbook and the vessels Safety Management System (SMS) for guidance
799. Which of these covers the rules and regulations for General Average on a Bulk Carrier?

The York Antwerp rules

800. Which special regulations cover transportation of grain on a Bulk Carrier?

IMO Grain Rules?

801. Which special regulations cover transportation of solid Bulk cargoes?

IMO Bulk Cargoes Code (BC) and the IMO International Maritime Solid Bulk Cargo Code( IMSBC)

802. Why do structural steel products often shift or collapse in a bulk carrier's cargo holds?

Because the irregular shape of the cargo holds results in void spaces

803. Why is air draught an important consideration when loading bulk cargoes on Bulk Carriers?

Because of movement of the bulk cargo loader or unloaders

804. A container vessel has lost several dangerous goods containers overboard. The master must report this loss of
container incident to:

The nearest Coastal state.

805. A heavy piece of machinery is loaded on deck of a container vessel, stowed across several flat rack containers.
The most appropriate method for lashing such cargo would be by:

Taking all lashings to the flat-rack lashing points.

806. Besides normal loads, the lashings of the containers stowed at the outboard part of the deck stow are
additionally subjected to:

The effect of wind on the containers.

807. Best location to stow containers loaded with Calcium Hypochlorite would be:

On deck, away from sources of heat.

808. Bulk liquid cargoes carried in flexi-tank containers are considered dangerous:

When the associated material safety data sheet shows a constituent(s) listed in the IMDG Code.

809. During a loaded winter passage across the North Atlantic, the master of a container vessel would be most
concerned with:

The added weight of icing on container stacks, leading to loss of GM.

810. During a loaded winter passage across the North Atlantic, the master of a container vessel would be most
concerned with:

Metacentric height of the vessel.

811. For guidance on lashing arrangement of containers on-board the vessel, the most important document to
refer is:

The Cargo Securing Manual.


812. On multi-purpose vessels, responsibility for the stowage and securing of containers is:

Determined by the clauses of the charter-party.

813. The Code of Safe Practice for Cargo Stowage and Securing was prepared to give guidance for:

Preparation and content of the Cargo Securing Manual.

814. The dangers associated with carriage of empty tank containers is that:

They may contain flammable cargo residue.

815. The direction of wave encounter that is most likely to cause a parametric roll condition on large container
ships is:

Head seas.

816. The most appropriate measure to reduce the build-up of ice on containers during a sea passage is to:
Reduce speed, whilst maintaining course.

817. The most appropriate method for adjusting the trim on a container vessel would be:

By internal shift of ballast.

818. What is the master's position if he is asked to load a container that is incorrectly manifested, but which is
believed to contain dangerous goods, about which insufficient information is supplied?

He has the authority to refuse it.

819. When taking action to deal with under-deck cargo spillage on container ships, reference must be made to:

The ems Guide.

820. With regards to carriage of Calcium Hypochlorite in containers, as per IMDG Code it is not allowed to:

Ship in Intermediate Bulk Containers (ibcs).

821. A chemical tanker may be granted, by the Government of the receiving Party, an exemption from carrying out
a mandatory prewash provided that the:

Unloaded tank is to be reloaded with the same substance or another substance compatible with the previous one
and that the tank will not be washed or ballasted prior to loading.

822. A tank which contained a category "X" product must undergo a prewash before leaving port in compliance
with MARPOL. The resulting residues shall be discharged to a reception facility until the concentration of the
substance in the effluent, as indicated by analysis of samples of the effluent taken by the authorized surveyor has
reached a level of:

0.1% by weight.

823. As per MARPOL, for control of discharge of Noxious Liquid Substances, the area(s) designated as ―Special
Areas‖ are:

Antarctic and North-West European Waters.


824. Ballast introduced into a cargo tank on a chemical tanker which has been washed to such an extent that the
ballast contains less than 1 ppm of the substance previously carried may be discharged into the sea without regard
to the discharge rate, ship's speed and discharge outlet location, but under certain conditions, which require:

That the vessel is not less than 12 miles from the nearest land and is in water that is not less than 25 metres deep.

825. Cargo residues of certain chemical substances are permitted to be removed by ventilation. This may be
carried out provided that:

The cargo discharged has a vapour expansion coefficient of at least 1.025.

826. Definitive information on whether a particular cargo is classified as a ―Noxious Liquid Substance‖ (other than
products provisionally assessed) can be obtained from:

The pollution category column of chapters 17 or 18 of the International Bulk Chemical Code (IBC Code).

827. If a cargo tank on a chemical tanker is to be cleaned by recirculation with a low flash or static accumulator
product:

The tank must be inerted to less than 8% oxygen content.

828. In respect of a chemical tanker, carrying category ―X‖, ―Y‖ & ―Z‖ Noxious Liquid Substances, the term
―Clean Ballast‖ as defined in the IBC Code means:

Ballast water carried in a tank which, since it was last used to carry a cargo containing a substance in category
"X","Y" or "Z", has been thoroughly cleaned and the residues resulting there from have been discharged and the
tank emptied in accordance with the appropriate requirements of Annex II.

829. In the event of an accidental or other exceptional discharge into the sea of a Noxious Liquid Substance or
mixture containing such a substance, an entry shall be made in the Cargo record Book, which shall include:

Time of occurrence

Approximate quantity, substance(s) and Category(ies) Circumstances of discharge or escape and general remarks.
Date of occurrence

830. The ‗dew point‘ of a liquid chemical can be defined as:

The temperature at which a gas is saturated with respect to a condensable component, as in operational terms is
seen at the point when air is saturated with moisture.

831. The carriage of a new Noxious Liquid Substance not yet listed in the IBC Code may be considered possible,
provided it is achieved through a ‗tri-partite‖ agreement between:

The Shipper / the Receiver / the Operator or Charterer.

832. The chemical term for a substance used as an additive to start a chemical reaction and speed up the cleaning
of a cargo tank on a chemical tanker is:

Catalyst.

833. The document which confirms whether a chemical tanker is authorised to carry a particular Noxious Liquid
Substance, is called:

The (International) Certificate of Fitness.


834. The tank cleaning requirements for a Category ―X‖ substance on a chemical tanker constructed after 01
January 2007, require the vessel to carry out:

Prewash / strip to 75 litres / 12 miles from land / 25 metres of water / minimum 7 knots, proceeding en route /
discharge below waterline.

835. Vegetable Oils as per MARPOL are classified under:

Category "Y".

836. What is the name given to the risk assessment programme developed by OCIMF, under which tankers are
inspected and the results made available to potential charterers through a database of records?

The Ship Inspection Report Programme (SIRE).

837. When cleaning a cargo tank after carriage and discharge of Sulphuric Acid, it is important to ensure that:

Once cleaning commences, large quantities of washing water can be delivered as quickly as possible, so that the
acid is quickly diluted.

838. When small amounts of cleaning additives (detergent products) are added to water in order to facilitate the
washing of tanks which previously contained liquid chemicals, must be ensured that:

No additives containing Pollution Category "X" components shall be used, except those components that are
readily biodegradable and present in a total concentration of less than 10% of the cleaning additive. No restrictions
additional to those applicable to the tank due to the previous cargo shall apply.

839. You are to load a number of chemical cargoes in Rotterdam in December, for eventual discharge in Australia,
after the ship has called at Singapore and Malaysia. None of the cargoes on board at any stage of the voyage
require heating. None of the tanks to be discharged in Singapore and Malysia will require hot washing after
discharge. When determining the filling limits of the tanks containing the Australian cargoes, you will need to
consider that:

The maximum anticipated temperature that the cargoes will reach bearing in mind ambient air and sea
temperatures to be encountered on passage, so that any expansion does not result in overflow.

840. A greater number of lashings may generally be required to secure cargo forward on deck compared with
amidships under deck of a General Cargo Vessel, because:

The dynamic stresses on the lashing are much greater in the forward areas of the vessel.

841. A loaded General Cargo ship is bound from Brazil to Rotterdam during winter time. During the voyage,
ventilation in cargo spaces should:

Be carried out during voyage, as the vessel is moving from warm to colder areas.

842. Additional lashings on general cargoes must be considered when:

Heavy weather is anticipated for the planned voyage.

843. For a General Cargo ship not specifically designed for carriage of containers, the maximum stowage height for
containers on deck is limited to:

One container high.

844. For a General Cargo ship to load Dangerous Goods in packaged form, it must have on board a:
Document of Compliance for carriage of dangerous goods.

845. For special category spaces on board general cargo ship, the minimum required air changes per hour should
be:

846. Information on the forces that may cause cargo shifting on a general cargo vessel may be available by
referring to:

The Cargo Stowage and Security (CSS) Code.

847. On a voyage from cold to hot climate countries, the ventilation of cargo holds of a General cargo ship should:

Not be carried out at all.

848. On a voyage from hot to cold climate countries, the ventilation of cargo holds of a General cargo ship should:

Be carried out continuously during the voyage.

849. The IMO Cargo Stowage and Securing Code (CSS) indicates in the 'Rule of Thumb', the total strength of the
lashings on each side of a heavy lift; what is the stated value ?

The Maximum Securing load of the lashings must equal the weight of the cargo unit.

850. The minimum information to that must be provided be given on a dangerous goods declaration on a General
Cargo Vessel should be:

IMO Class, UN Number, Gross weight, number of units of cargo, Proper Shipping Name.

851. The most important consideration when planning the lashing system for a particular sea route on a General
Cargo Vessel is:

Transverse accelerations.

852. The segregation requirements for Dangerous Goods to be loaded on a General Cargo ship may be obtained by
referring to:

The IMO International Maritime Dangerous Goods Code.

853. The two main considerations when choosing an appropriate paint for a cargo space of a General Cargo vessel
would be:

Corrosion resistant and heat resistant.

854. Which of these can be loaded in the same hold of a General Cargo Vessel, as steel coils?

Steel rebars

855. How can you best demonstrate in an audit that you follow company cargo handling procedures?

By being able to provide comprehensive and verifiable documentary records of cargo operations.

856. If all indications are that a cargo has been received without damages, irregularities or short shipment and the
phrase "apparent good order and condition" is entered on the Bill of Lading, what type of Bill is this said to be?

A clean Bill of Lading.


857. What may be issued by the shipper to indicate that a vessel or her operators will not be held responsible for
any damage that may arise from the carrier issuing a clean Bill of Lading, even though the Mate's receipt is marked
as "unclean", such as may apply to atmospheric corrosion on steel plates that have been waiting in a port facility
for some time awaiting shipment?

A Letter of Indemnity.

858. What term is applied to the compensation payment by the charterer that is due when a vessel is unable to
load / discharge her cargo within the allowed and contracted time?

Demurrage.

859. What type of Bill of Lading covers "door to door" shipment?

A Through Bill of Lading.

860. When conducting a risk assessment for a shipboard work activity, what are the two elements to be
considered?

The potential severity of harm and the likelihood that harm will occur.

861. According to SIGTTO publications, what is a typical accuracy for LNG pressure measurement equipment?

+/- 0,0015 bar (which will apply within the MARVS of the tank)

862. According to the IMO Gas Codes, what is the minimum number of "Firemen‘s outfits" required to be carried
on an LNG carrier with a cargo capacity above 5,000 m3?

5 sets

863. Carbon dioxide, CO2, can solidify and form dry ice at low temperatures. What is the solidifying temperature of
CO2?

Approximately minus 78.5 C

864. Does MARPOL apply to LNG carriers?

Yes, MARPOL applies to all ship types..

865. Does the Oil Pollution Act, 1990 (OPA90) apply to vessels engaged in carrying liquefied natural gas (LNG)?

Yes, OPA90 applies to all ships.

866. Due to the very low carriage temperatures for LNG the thermal conductivity, k value, is an important property
of the insulation material used in cargo containment systems. For a given rate of heat leakage across the insulation,
which of the following statements is true?

The rate of heat leakage is unaffected by the thickness of the insulation.

867. During cargo tank gassing up and cooling down operations on an LNG carrier which of the given options,
regarding temperature, needs to be observed?

Never allow temperature of the insulation to fall below the safe minimum temperature.

868. Having water vapour in an LNG carriers cargo tanks prior to loading cargo is unacceptable due to ice formation
at low carriage temperatures. How can water vapour in the tank atmosphere be removed prior to the cooling
down and loading operation?
By displacing the tank atmosphere with pre-dried inert gas.

869. What is the approximate normal daily cargo "boil off" rate for an LNG carrier of 125000 cubic metre cargo
capacity?

From 0,15 % to 0,20 % per day of total cargo.

870. What is the normal procedure for cooling down the a cargo tank prior to loading LNG?

Introducing liquid LNG into the tank slowly through the spray lines.

871. What is the typical accuracy for onboard LNG temperature measurement systems?

+/- 0.2 C in the range of - 150 C / - 170 C

872. Which of the gas groups, identified by SIGTTO, in 'Liquid Gas Handling Principles on Ships and in Terminals',
does LNG belong to?

Saturated Hydrocarbons

873. Which term is usually used to describe the compressor that collects the boil-off from the header connected to
each cargo tank of an LNG carrier?

The low-duty compressor.

874. Why is nitrogen used for the inerting of hold spaces and interbarrier spaces on LNG carriers?

Because the carbon dioxide in combustion generated inert gas would freeze when in close proximity to the cargo.

875. With reference to preparations of LNG carrier cargo tanks for cargo loading operations, how can it be
determined that the cool down operation is complete?

When temperature monitor, or liquid level gauge, shows that liquid is forming in the bottom of the cargo tank.

876. Before loading a refrigerated cargo of LPG the cargo tanks must be cooled down slowly in order to minimise
thermal stresses for the vessel and the cargo containment system. What is the generally accepted cooling down
rate?

10 degrees C per hour.

877. Cargo tanks on an LPG carrier can be inerted using either inert gas from a combustion type inert gas generator
or by using nitrogen. Is gassing up of an inerted cargo tank with LPG allowed when the tank contains combustion
generated inert gas?

Yes, it is always allowed if the atmosphere of the inerted tank has an oxygen content of less than 5% by volume.

878. During pre-entry checks of an enclosed space onboard a liquefied gas carrier it is necessary to check the
condition of the atmosphere. If the gas detection equipment to be used for the checks included a catalytic type
combustible gas indicator, an absorption type toxic gas detector and a paramagnetic type oxygen analyser, which
would be the preferred order for the checks?

Oxygen content followed by hydrocarbon gas content and then toxic gas content.

879. IMO publishes a number of Codes relating to the carriage of bulk cargoes including the IGC Code for liquefied
gas carriers. What is the main purpose of the IGC Code?
To provide an international standard for the construction of, and equipment for, gas carriers to ensure the safe
carriage of liquefied gases in bulk.

880. Inhibitors are often added to liquefied gas cargoes prior to loading to prevent or slow down polymerisation.
An inhibitor information form or certificate must be provided by the cargo shipper to the vessel. What sort of
information must this certificate contain about the inhibitor in addition to the technical name and quantity added?

Expected lifetime of the inhibitor and the date the cargo tanks were inhibited

881. Is it permitted to load fully refrigerated propane directly onto a fully pressurised LPG carrier without
additional conditioning of the cargo or cargo spaces?

Only if the cargo containment system is designed for temperatures of minus 48 degrees C or less.

882. It is necessary for personnel to enter a liquefied gas carrier cargo tank to clean up some dust and other loose
debris. What are the permit requirements before entry into the tank is allowed?

Only an Enclosed Space Entry Permit is required.

883. Liquefied gas cargoes will expand as the temperature increases and therefore tanks are not allowed to be
filled to 100%. What is the maximum allowable filling limit for the cargo tanks on liquefied gas carriers?

Maximum allowable filling limit on cargo tanks is 98% on gas carriers.

884. What is the full title of the IMO code which applies to all gas carriers built after 1986?

The International Code for Ships Carrying Liquefied Gases in Bulk (the IGC code)

885. What is the main reason for adding inhibitors to some liquefied gas cargoes such as ethylene oxide and vinyl
chloride?

To control the temperature of the cargo.

886. What is the requirement for the atmosphere in the hold spaces surrounding cargo tanks that require a
secondary barrier when carrying LPG cargoes?

The hold spaces must be kept in an inert condition whenever there is cargo in the cargo tanks.

887. What method should be used to discharge a semi-pressurised gas carrier if there is a break down on the cargo
discharge pump?

By using the cargo compressor to pump the cargo vapour ashore as it boils off.

888. When a ship is switching from ammonia to LPG virtually all traces of vapours must be removed. What is the
allowable concentration of ammonia vapour in the tank prior to loading the next cargo?

Less than 20 parts per million.

889. Which certificate is issued to LPG and other liquefied gas carriers in accordance with the IGC code?

The Certificate of Fitness is issued in accordance with the IGC code

890. With some liquefied gas cargoes special conditions must be met before they can be loaded into a cargo tank.
Is it permitted load ammonia into an inerted cargo tank?

Ammonia cannot be loaded into any tank with an inert atmosphere.


891. A VLCC is to anchor in a depth of 80 meters in open water with moderate swell running. How many shackles of
anchor chain should be used to aid a safe anchorage?

11 shackles

892. After the last entry being made, the retention period of an oil record book on board must be:

Not less than 3 years after the date of the last entry.

893. Any person who can assume overall charge of the ships crude oil washing operation must have:

At least 12 months appropriate experience on oil tankers, have participated in at least two COW programmes and
be fully knowledgeable of the contents of the Operations and Equipment Manual.

894. As per MARPOL, Oil Record Book Part II, Cargo/Ballast Operations, must be carried and completed on oil
tankers of:

150 gross tonnes and above.

895. As per MARPOL, the contents of lines and pumps on an oil tanker at completion of discharge must be:

Discharged ashore or retained on board as per the pre-discharge agreement made between the ship and shore.

896. As per requirements of the International Convention for the Control and Management of Ship's Ballast Water
and Sediments, oil tankers must have a plan on board to achieve:

95% volumetric exchange of the ballast taken on-board at the previous port.

897. As per the OCIMF Ship to Ship Transfer Guide (Petroleum) guidelines, both vessels engaged in the cargo
transfer operation shall:

Have their duty engineers on stand-by so as to prepare the engines if required for use at any time

898. As per the US Code of Federal Regulations, the current Oil Transfer Procedures for a vessel carrying out
discharge in US ports must be:

Available on board, legibly printed in a language or languages easily understood by personnel engaged in the
transfer operation and permanently posted or available at a place where crew members can see and use them.

899. Crude Oils required by MARPOL to be specifically listed in a tanker's Crude Oil Washing manual as unsuitable
for COW are:

Those with high pour point or viscosity.

900. Depending on density or API, an error measurement of 0.1 degree Fahrenheit in a tank containing 50,000
cubic metres (314,491 barrels) of oil will result in which of the following volumes?

25 cubic metres (157 barrels).

901. For a vessel proceeding enroute, located more than 50 nm from nearest land outside a special area and
having in operation its ODME, the maximum instantaneous rate of oil discharge (from washings of cargo tanks) in
to the sea is:

30 litres per nautical mile.

902. On board an oil tanker, slop tanks may be used for the carriage of oil:
Only on clean ballast tankers and are only included in the total cargo capacity of this type of vessel.

903. Prior to discharging cargo from an oil tanker, ‗line displacement‘ or ‗line pressing‘ must be conducted to
ensure:

Testing of the automatic shut-down arrangements in the shore line system.

904. The details of an internal transfer of oil must be entered in the Oil Record Book:

Only if required by the specific instructions of the owners or Flag State of the vessel

905. The ideal maximum viscosity at which aromatic crude oil cargoes are best discharged at, is:

250 cst (250 mm2/s)

906. The maximum permitted oxygen content in the inert gas main when inerting a cargo oil tank prior to gas
freeing is:

5% by volume.

907. The ODME printouts for tank cleaning operations must be retained on board for a minimum period:

Of 3 years.

908. The recommended guideline for avoiding the risk of electrostatic potential in a mist produced by using oil and
water during Crude Oil Washing operations is that:

Before washing begins, any tank that is to be used as a source of oil for Crude Oil Washing should be partly
discharged to remove any water that has settled out during the voyage. The discharge of a layer of at least 1
metreis necessary for this purpose.

909. To correctly report an oil spill in US waters:

The person in charge must report the spill to the National Response Center or, if not practicable, to the
Environmental Protection Agency regional office or local U.S. Coast Guard Marine Safety Office. This must be done
immediately that person has knowledge of the spill.

910. What do we mean with a IOPP certificate?

With IOPP certificate we mean International Oil Pollution Prevention certificate and the ship is classed to prevent
oil pollution

911. When discharging dirty ballast from an oil tanker at a high flow rate with main cargo pumps, the
instantaneous rate of discharge of oil is calculated by formula:

Instantaneous rate of discharge (l/nm) = oil content (ppm) x flow rate (m3/h) / speed (knots) x 1,000

913. When internally transferring any oil cargo within the vessel, the correct procedure would be to:

Obtain permission from the charterers and document all operations fully in the Oil Record Book.

914. Within the Oil Discharge Monitoring and Control System, an ‗overboard discharge control‘ is defined as:

A device which automatically initiates the sequence to stop the overboard discharge of the effluent in alarm
conditions and prevents the discharge throughout the period the alarm prevails.
915. A hazard is is a source of potential harm or damage or a situation with potential for harm or damage. Risk is
determined based on evaluation of two elements. Which two elements?

The likelihood that a hazard may occur and the consequences of the hazardous event

916. How frequently should the PA-system (Public Address) be tested?

Every week

917. How often shall abandon ship- and fire drills take place on board passenger ships?

Weekly

918. How often shall drills for the operation of watertight doors, side scuttles, valves and closing mechanism of
scuppers, ash-chutes and rubbish chutes take place in passenger ships?

Weekly

919. How should chemicals and harmful substances be stored on board?

In a separate locker. The locker shall be clearly marked, locked and ventilated.

920. Personnel on board passenger vessels must undergo training courses before they can be part of the safe
manning and assigned to emergency duties on board. What is minimum training requirement for all personnel?

Basic Safety Training Course and Crowd & Crisis Management Training Course

921. SOLAS regulations require surveys of ships to be carried out at certain times and at certain intervals. Which of
the following surveys apply to passenger ships only?

Periodical survey every 12 months

922. The International Convention for the Prevention of Pollution from Ships

(MARPOL) covers detailed regulations to prevent various sources of ship

generated pollution. Annex I - VI deals with regulations for the prevention/ control

of pollution from:

Harmful Substances in Packaged Form, Sewage, Air Pollution, Garbage, Oil and Noxious Liquid Substances in Bulk

923. What information is required on passengers prior to departure?

All persons on board shall be counted and details of persons who have declared a need for special care or
assistance in emergency situations shall be recorded and communicated to the Master

924. What is important to prepare prior to a helicopter operation?

Make sure all loose deck equipment at helicopter deck is stowed away and secured.

925. What is the purpose of Material Safety Data Sheets?

To provide all personnel including emergency personnel with procedures for handling or working with that
substance in a safe manner

926. What necessary precautions should be taken before entering a tank or an enclosed space?
Make sure that the tank/ enclosed space is gas free, ventilated and the oxygen content is measured. O2 content
shall be 21% before entering the tank/ enclosed space

927. Which international convention deals with maritime safety and safety equipment onboard ro-ro passenger
vessels?

SOLAS

928. Who is responsible to ensure that all personnel on board are provided with suitable Personal Protective
Equipment where it is needed?

The Company/ employer

929. You are burning garbage containing plastics. What shall you do with the ashes from the vessel's incinerator?

Discharge the ashes to a shore facility

930. A cellular container vessel is to load frozen ice cream in containers. Space is available either in the hold or as a
deck stow. Select, from the options given, the most suitable stowage position, with the reason, for this cargo.

The deck stow as it is less sensitive to temperature in the event of a mechanical problem.

931. A conventional reefer vessel operating a Controlled Atmosphere (CA) is approaching the port of discharge in
Northern Europe. Which is the most suitable action to take from the options given?

Turn off the CA plant and thoroughly ventilate the cargo spaces under CA with fresh air just prior to arrival.

932. A reefer vessel is loading a cargo of fruit alongside in a South African port. During loading another vessel
arrives at an adjacent berth to have its cargo discharged after having been towed in following a fire onboard which
had resulted in abandonment. What should concern the Master of the reefer vessel most about the situation?

That the cargo may be contaminated by the smell of smoke and the products of combustion from the damaged
vessel.

933. A reefer vessel is to load a cargo of plantains and bananas. Due to space restrictions both have to be loaded
into a common space. The usual delivery temperature for bananas is about 13 degrees Celsius and for plantains it is
7 degree Celsius. What would be the best delivery temperature for the mixture of these two fruits?

13 C as plantains are less sensitive to the consequences of a higher delivery temperature.

934. A reefer vessel is to load a part cargo of frozen beef hocks (large joints of beef, usually quarters, not packed in
cartons). In deciding which would be the most appropriate space on a conventional reefer vessel, which of the
given options would be the preferred choice?

1C deck as this is the narrowest space on the vessel and will best constrain the cargo from any possible movement
during the voyage.

935. A reefer vessel, which is about to carry a palletised cargo, has to have available sufficient cargo equipment
including air bags (dunnage bags), air lines and valves, cargo slings, wooden dunnage, nails, etc. These items are
required to ensure a quick loading operation and a successful passage. Complete the following statement from the
options given. "Air bags are particularly important in that ….

… they reduce the movement of the pallets and prevent short circuiting of the air flow."
936. A situation arises where there is insufficient fruit cargo available to fill a cargo space. There is a cooler
arrangement (cooler/evaporator/brine nest/fans) positioned at one end of the cargo space. Select, from the
options given, the best method for stowage of the fruit.

Start at the end with the cooler arrangement and work away from the cooler.

937. A situation exists where a cargo of palletised fruit is being loaded to capacity on a conventional reefer vessel.
In order to load all of the available cargo it is proposed to break down some of the pallets and place the loose
cartons on top of the pallets; there is just enough space to accommodate this below the deckhead. From the
options given which is the most suitable action to take?

Reject the plan as the reduced gap at the top of the stow will restrict the return air flow.

938. A standard convention for a 4 deck reefer vessel is to designate the decks A to D from upper to lower deck.
Decks A and B common as are C and D with a gas tight seal between B and C. Apples are to be carried in decks C
and D with bananas in A and B. Which of the options is the best to avoid the risk of crossover of temperature and
respiration between the two cargoes?

Create a pressure differential with a higher pressure in decks C and D.

939. After discharge of any refrigerated cargo a thorough inspection of the vessel should be carried out before
presenting the vessel for loading the next cargo. Amongst the reasons for this is to ensure that any traces of or
residues from the previous cargo are removed. This is particularly so if a fruit or meat cargo is to be loaded after a
fish cargo has been carried. Select, from the options given, the main reason for this requirement.

Fish is strong smelling and the odour may contaminate the next cargo.

940. Apart from temperature there are few differences between carrying cargoes of chilled meat, minus 1 degree
Celsius, and frozen meat, minus 18 degrees Celsius. A key difference is that for frozen meat the cooling fans are
operated at half speed or some are switched off whereas for chilled meat the fans are run constantly at full speed.
Select, from the options given, the main reason for this difference in fan operation.

The chilled meat is more sensitive to damage and therefore tighter temperature control is necessary.

941. In preparing a reefer vessel for loading the next cargo a careful inspection of the cargo spaces should be
carried out. All required maintenance and the repair of any damage identified during the inspection should be
completed prior to loading. Select, from the options given, the most appropriate action to be taken when the
maintenance and any repairs are completed.

Make a detailed record of all maintenance and repairs carried out for presentation to the supervisor at the
loading port as proof that the vessel is in an acceptable condition for loading the cargo.

942. On some trades fruit cargoes may be subjected to 'in-transit cold treatment' also known as cold treatment.
From the options given which is the main purpose of this cold treatment?

To maintain a specified minimum temperature for a prescribed time period to kill off any fruit fly which may be
present when loading the cargo.

943. Reefer vessels form part of the 'cold chain' in the transport of perishable goods from the producer to the
consumer. There are times when hatches have to remain open in less than perfect conditions, for example strong
winds. There are steps that can be taken however to mitigate the effects of this on cargo that has already been
loaded. Which of the options given could be considered to be the most important measure to counter the effect of
such conditions?

Refrain from ventilating the cargo with fresh air.


944. With the exception of some citrus fruits and bananas, fruit is usually pre-cooled to the required carriage
temperature prior to loading on a reefer vessel. In order to protect the cold chain, and to maintain the
temperature of the fruit, a minimum exposure time to ambient conditions during loading is necessary. What action
should the deck officers take during loading to achieve this minimum exposure time?

Close the hatches and apply cooling to the cargo already loaded during any break in cargo operations that exceed
30 minutes.

945. A Standard Ro-Ro unit weighing 18mt is to be loaded in the fore and aft direction and lashed by belts of SWL
2mt. Using the general rule How many lashing belts should be used to secure the unit?

9 on each side

946. A standard Ro-Ro unit weighing 2mt is to be loaded fore and aft and lashed by belts of SWL 0.6mt. Using the
general rule How many lashing belts should be used to secure the unit?

4 on each side

947. On a roro vessel, a ro-ro unit weighing 2mt is to be loaded in the fore and aft direction and lashed by belts of
SWL 0.6mt. How many lashing belts should be used to secure the unit?

4 on each side

948. On a roro vessel, a vehicle weighing 50mt is to be loaded in the fore and aft direction and lashed by
chains/turnbuckles of SWL 5mt. By the general Rule How many sets of chains/turnbuckles should be used to secure
the unit?

At least 10 per side

949. On a roro vessel, how often should a dangerous goods stowage plan be produced

Every time you load a dangerous cargo

950. On a roro vessel, if the vessel is loaded by stevedores, who is responsible for the lashing of the cargo

The vessel is responsible for cargo as soon as it crosses the ramp including its securing

951. On a roro vessel, what dangers are associated with using a steep loading ramp?

The ends of ro-ro units can be damaged

952. On a roro vessel, what instruction should be given to the crew about unlashing of cargo prior to arrival at the
berth

This can only be done when the bridge gives permission and no unit stowed on a ramp or incline can be unlashed.
Provided the company allow it.

953. On a roro vessel, what must be considered when planning the loading of ro-ro cargoes on ramps?

SWL and loading limit of the ramp and Minimum clearances for the operation of ramp doors

954. On a roro vessel, what must be ensured onboard the vessel prior to commencing cargo?

Cargo hold ventilation systems are operational

955. On a roro vessel, what standing instruction should be given to prevent a blackout on board?
Check with the duty engineer before switching on motors, fans or other machinery

956. On a roro vessel, what standing instruction should be given to protect the Ramps when loading ro-ro units?

Units whose weights exceed the ramp load density/SWL must not be loaded

957. On a roro vessel, what stowage factors should be taken into account when planning the loading of cars?

The longitudinal and athwartship distances between the cars

958. On a roro vessel, which of the following is not required in the pre-stowage plan?

Checking communications equipment

959. On a roro vessel, which of the ships trading certificates details the type and location that dangerous goods are
allowed to be stowed onboard

Certificate of compliance for the carriage of Dangerous goods

960. On a roro vessel, which of these situations will result in an emergency shutdown of cargo operations?

Any of the listed situations

961. On a roro vessel, which regulations require supervising the embarkation of persons on board ship?

The International Ship and Port Facility Security (ISPS) Code

962. Under SOLAS, what are the minimum required air changes per hour for 'Special Category Spaces' on a roro
vessel,?

10

963. What must not be obstructed when planning the loading of ro-ro cargoes?

Access to fire-fighting equipment

964. A hazard is is a source of potential harm or damage or a situation with potential for harm or damage. Risk is
determined based on evaluation of two elements. Which two elements?

The likelihood that a hazard may occur and the consequences of the hazardous event

965. How can the Master ensure that all cargo loading doors, bow visors, weathertight ramps etc. Are locked and
secured before the ship proceeds on any voyage?

By having an effective system of supervision and reporting of the closing and opening of doors. Time of closing
and opening of doors shall be entered in the log-book.

966. How frequently should the PA-system (Public Address) be tested?

Every week

967. How often shall abandon ship- and fire drills take place onboard ro-ro passenger vessels?

Weekly

968. How often shall drills for the operation of watertight doors, side scuttles, valves and closing mechanism of
scuppers, ash-chutes and rubbish chutes take place in passenger ships?
Weekly

969. How should chemicals and harmful substances be stored on board?

In a separate locker. The locker shall be clearly marked, locked and ventilated.

970. On most ro-ro passenger ships there is no requirement to carry out drills with the passengers. What is the
most effective ways of informing embarking passengers about the emergency procedures?

Information on boarding cards, public announcement on departure, posters in public areas and cabins, safety
video running continuously

971. Personnel on board ro-ro passenger vessels must undergo training courses before they can be part of the safe
manning and assigned to emergency duties on board. What is minimum training requirement for all personnel?

Basic Safety Training Course and Crowd & Crisis Management Training Course

972. The International Convention for the Prevention of Pollution from Ships

(MARPOL) covers detailed regulations to prevent various sources of ship generated pollution. Annex I - VI deals
with regulations for the prevention/ control of pollution from:

973. Harmful Substances in Packaged Form, Sewage, Air Pollution, Garbage, Oil and Noxious Liquid Substances in
Bulk

974. Oil, Noxious Liquid Substances in Bulk, Harmful Substances in Packaged Form, Sewage, Garbage and Ballast
Water

975. Proper Pollution Prevention Training

976. All Harmful Substances we have onboard

977. What information is required on passengers prior to departure?

All persons on board shall be counted and details of persons who have declared a need for special care or
assistance in emergency situations shall be recorded and communicated to the Master

978. What is important to prepare prior to a helicopter operation?

Make sure all loose deck equipment at helicopter deck is stowed away and secured.

979. What is the purpose of Material Safety Data Sheets?

To provide all personnel including emergency personnel with procedures for handling or working with that
substance in a safe manner

980. What necessary precautions should be taken before entering a tank or an enclosed space?

Make sure that the tank/ enclosed space is gas free, ventilated and the oxygen content is measured. O2 content
shall be 21% before entering the tank/ enclosed space

981. Which international convention deals with maritime safety and safety equipment onboard ro-ro passenger
vessels?

SOLAS
982. Who is responsible to ensure that all personnel on board are provided with suitable Personal Protective
Equipment where it is needed?

The Company/ employer

983. You are burning garbage containing plastics. What shall you do with the ashes from the vessel's incinerator?

Discharge the ashes to a shore facility

984. A bulk vessel loads a full cargo to summer marks of a high density bulk cargo such as iron ore concentrate;
what would be the possible stability conditions produced?

The vessel will normally have a large intact metacentric height (GM) and have a fast roll period

985. A cargo hatch cover seal on a Bulk Carrier is known to be damaged and not weather tight prior to sailing; what
is the legal significance of this situation?

The vessel may well be judged to be un-seaworthy; this could invalidate some certification and hull and machinery
insurance

986. Before a solid bulk cargo is loaded, the Master and shore representative must agree a loading plan which
covers which of the following aspects?

All of the items specified in the possible answers

987. How are cargoes on self-unloading bulk carriers fed to the vessel's conveyor belts during discharge?

Via hydraulically-operated hopper gates at the bottom of each hold

988. The high level water ingress alarm in number 1 hold of a Bulk Carrier activates in bad weather at sea; what
would be the actions of a prudent Master?

Sound general alarm, muster ships crew and transmit a Mayday call and message.

989. Under international regulations for a Bulk Carrier, who needs to be trained in the use of oxygen analysis and
gas detection equipment?

The ship's crew

990. What does the IMSBC Code emphasise with reference to the exposure of personal to the dust created when
carrying some bulk cargoes?

A high standard of personal hygiene

991. What extent of hatch cover spares should be available on board a Bulk Carrier at all times?

Specimen fittings shown in the hatch cover manufacturer's manual

992. What height of water above the inner bottom will activate the cargo hold high level alarm on a Bulk Carrier

Any height above 2.0m

993. What is the maximum period between the sampling/testing of the moisture content of a solid bulk cargo and
the loading of that cargo into a bulk carrier?

A maximum for seven (7) days, when there has been no change in the moisture content due to rain or snow
994. What must be specified when ordering gas detection equipment when used in association with bulk carriers?

That the instrument is suited for its purpose of application

995. What specific data must be displayed on the loading instruments carried on bulk carriers of 150m or more in
length?

The shear forces exerted on the hull structure associated with the entered loaded weight distribution

996. Where are cargo hold water level detectors required to be fitted on bulk carriers?

At the after end of each cargo hold

997. Which of the following is a warning sign of a faulty hydraulic hatch cover system on a Bulk Carrier?

A fall in the hydraulic header tank level

998. Who needs to be trained in the use of oxygen analysis and gas detection equipment?

The entire ship's crew

999. Why do bulk cargo carriers need to carry oxygen analysis and gas detection equipment?

Because of enclosed or confined space entry requirements

1000. Why do the cargo holds of a self-unloading bulk carrier have a "W" shaped cross section?

So that during discharge the cargo will automatically fall onto the underlying conveyor belts

1001. A vessel has lost several containers overboard during a voyage. Upon arrival into port, she is being inspected
by the attending surveyors. The most important item to be checked during this inspection would be:

Certificates of approval related to lashing equipment used to secure those containers.

1002. An inspection in the amidships area of the weather deck of a Panamax container vessel has revealed cracks
in the hatch coamings. It is extremely important to urgently inspect the:

Longitudinals in the double bottom tanks in the amidships half length of the vessel.

1003. For a ships loading computer to be safely used for loading planning and stress calculations, it must be
approved by:

A Classification Society.

1004. On a container vessel, flexitanks are used for:

The carriage of non-hazardous liquids, in bulk.

1005. Racking forces imposed on a container would likely cause the greatest deflection to:

The door end of the container.

1006. Shock loads in a container lashing system are generally caused by:

Loose cargo lashings.

1007. The correct weight of a wrongly declared container may be best indicated by:
Strain gauges fitted to the shore gantry cranes.

1008. The most appropriate way of dealing with twist-locks suffering from excessive wear and tear is to:

Isolate them from use and dispose them appropriately.

1009. The most dangerous consequence of the corrosion and wear down of container stools on weather
deck/hatch tops of a container vessel would be:

Collapse of the deck stool, leading to lashings becoming slack.

1010. The most effective method of dealing with an under-deck cargo space fire on board a container ship, is to:

Deploy the fixed firefighting system.

1011. The most important function of a buttress fitting on a container vessel is:

To transfer forces from the container stow to the ships structure.

1012. What contributes to wear-down of twistlocks on a container vessel?

The continuous action of longitudinal forces.

1013. What items of container securing equipment must be used in conjunction with buttresses?

Double stacking cones or link plates.

1014. When planning the loading of containers, the planning officer must refer to:

The Cargo Securing Manual (CSM).

1015. "Passivation" is a restorative process periodically applied to stainless steel tanks on a chemical tanker. What
effect does this process have on the steel surface?

It restores and reforms the passive Chromium Hydroxide surface layer.

1016. A cargo pumproom or other enclosed space which contains cargo handling equipment on a chemical tanker
shall be fitted with a mechanical ventilation system, capable of being controlled from outside the space. What is
the minimum number of atmosphere changes per hour, based on the total volume of the space, that such a system
must deliver?

Not less than 30 changes per hour.

1017. Basic manual dew point measurement devices are commonly used by surveyors when monitoring the
dryness of a cargo tank prior to loading a liquid chemical product. Which of the descriptions below is a summary of
how the measurement is carried out?

A small quantity of Acetone is placed into the device and dry-ice is progressively added to it to steadily reduce the
temperature. A sample of the atmosphere in the tank is continuously drawn through the device, passing over the
polished or mirrored surface of the container. When the first drop of mositure (dew) is observed to form on the
polished surface, the temperature of the Acetone bath is noted. Reference may be required to tables to correct the
reading for desired parameters.

1018. Chemical tankers of 20,000 tonnes DWT or above, with a keel laid on or after 1st July 1986, when carrying
flammable products with a flashpoint not exceeding 60 degrees Celsius, such as those listed in chapters 17 and 18
of the International Bulk Chemical Code, are exempt from the requirement to be fitted with and use an inert gas
plant provided certain conditions are met. Which of the following is a summary of those conditions?
The cargo tank does not exceed 3000 cubic metres capacity / each tank washing machine nozzle does not exceed
17.5 cubic metres per hour delivery rate / the total wash water input to the tank from all tank washing machines
does not exceed 110 cubic metres per hour.

1019. High level and high-high level alarms must be tested at the tank for proper operation within 24 hours of the
start of cargo transfer on a chemical tanker. What acceptable alternative is there to this requirement?

That a function test is carried out by means of an automatic self-test and circuit monitoring facility within the
alarm system.

1020. How would you determine whether a particular cargo transfer hose was compatible with the chemical
product to be transferred?

Refer to the product entry in the hose manufacturer's chemical resistance chart.

1021. 118. If your chemical tanker is equipped with high velocity venting valves, at what minimum height above
the weather deck or catwalk should they be installed?

3 metres

1022. In a typical shipboard de-humidifier plant as may be found on a modern chemical tanker, operating on a
"rotating bed" principle, what names are given to the two parts of the rotating bed?

The "process sector" and the "reactivation sector".

1023. The IBC Code prescribes certain design conditions for a cargo heating or cooling system fitted to a chemical
tanker. What does it require in respect of pressure within such a system, for any condition other than when it is
empty?

That a higher pressure can be maintained within the system than the maximum pressure head that could be
exerted by the contents of the cargo tank on that system.

1024. The specified maximum working pressure of a cargo hose in service on a chemical tanker should be at least
which of the following?

10 bar gauge.

1025. To what pressure will a new length of cargo hose be tested by a manufacturer prior to its supply to a vessel
for service onboard a chemical tanker?

Not less than one and a half times its specified maximum working pressure, but not more than two-fifths of its
bursting pressure.

1027. What temperature defines "hot" water in the context of tank washing on a chemical tanker?

At least 60 degrees Celsius.

1028. When a submerged centrifugal cargo pump is being run at too high a speed during discharge of a viscous
chemical cargo, the pump may start racing, causing a heat build-up around the suction, possible localised
solidification of the cargo and consequent damage to the pump. What term is applied to this problem?

Cavitation.

1029. Which of the following is a summary of the features of a "controlled tank venting system" as may be found
on a chemical tanker?
PV valves are fitted to limit the pressure or vacuum in the tank; no shut-off valves may be fitted either above or
below the PV valves; provision may be made to by-pass the PV valves under certain operating conditions; such a
system shall consist of a primary and secondary means of allowing full flow of vapour, except that the secondary
system may be replaced by pressure sensors fitted within the tank.

1030. You are carrying a bulk cargo of Phosphoric Acid. Which components of the cargo pumps may be damaged as
a result of discharging this particular cargo and why?

The cargo seals may be damaged from the abbrasive effect of any sediment.

1031. A five yearly thorough survey of cargo gear on a General Cargo vessel should be carried out by:

A classification society surveyor.

1032. A General Cargo vessel has a 50 tonne SWL heavy lift derrick and a load of 48 tonnes is to be loaded. The
lifting gear of slings and spreader bar weighs 4 tonnes. In this case, it would be correct to state that:

The load cannot be loaded because the combined weight of the load and the lifting gear will exceed the SWL by
two tonnes.

1033. During a pre-loading survey on board a General Cargo ship, the most efficient method of testing the weather
tightness of the hatch covers is considered to be:

Ultra sonic test.

1034. During cargo watch on a General Cargo ship, if the OOW informs you that the condition of the discharge
equipment such as slings and shackles being used by the stevedores is unsuitable for use, you should:

Inform stevedores of concern and protest by letter.

1035. Information about the maximum point loading in cargo holds and on decks of a General Cargo Vessel may be
obtained from:

Ships Capacity plan.

1036. On a general cargo ship, operating the heavy lift derricks with the boom close to horizontal could result in:

Excessive stresses acting on parts of the derrick system.

1037. On a General Cargo ship, the most likely cause of a hatch cover hydraulic system to deteriorate would be:

Due to dust and cargo particles lodged around the piston seals.

1038. On a General Cargo vessel, a 16T derrick should be tested to a proof load of:

20T

1039. Prior to loading cotton on a General Cargo vessel, it is important to ensure that:

The cargo hold fire-fighting system is thoroughly examined.

1040. Prior to loading general cargo on a General Cargo vessel, with regard to lashing wires, terminations, shackles,
turnbuckles, pad eyes and D rings etc., you must make sure that:

They must all be certified and be visually inspected for any apparent damage.

1041. Proper guidance on the stowage and securing of general cargo may be obtained by referring to:
IMO Code of practice for stowage and securing of cargoes.

1042. The lifting plant on a General Cargo vessel be proof load tested:

When equipment is new, every five years and after repairs or major modifications.

1043. The main purpose of a hatch cover ventilator grill on a General Cargo vessel is:

To prevent sparks entering the cargo hold.

1044. The ship‘s lifting plant must be proof load tested and all parts thoroughly examined at intervals not
exceeding:

5 years

1045. When general cargo is damaged during heavy weather on a General Cargo vessel, it must be ensured that
the damage is inspected by the:

Surveyor representing the vessel's P. & I. Club.

1046. According to "Summary of minimum requirements" in the IGC Code, what is the requirement for vapour
detection for methane (LNG) cargoes?

Flammable vapour detection.

1047. According to the IMO Gas Code, what is the requirement for the number of sets of portable gas detection
equipment that must be carried onboard an LNG carrier?

There must be at least two sets.

1048. According to the IMO Gas Codes, what are the maximum time intervals for sampling and analysing samples
from the permanent installed gas detection system on a LNG carrier?

30 minutes.

1049. According to the IMO Gas Codes, what is the required number of temperature indicating devices in the cargo
tanks of an LNG carrier?

At least two devices in each tank.

1050. Gas carrier type A and B cargo tanks have a MARVS of less than 0.7 barg? What is the liquid and vapour
connection shut off valve requirement for this type of tank according to the IMO gas codes?

Single shut-off valves with manual closing facility.

1051. LNG tankers are often fitted with fixed water spray system for fire protection purposes for deck areas, deck
tanks, deck manifolds and pipelines. What is the minimum required flow rate of water per minute for horizontal
and vertical surfaces to ensure adequate, uniform coverage of these areas?

10 litre/m2 per minute for horizontal surfaces and 4 litre/m2 per minute for vertical surfaces.

1052. Select, from the options given, the one that best describes a requirement of the remotely controlled valves
fitted in the ESD (Emergency Shut-Down) systems on an LNG carrier?

They must be fail-safe.


1053. Some LNG carriers are fitted with a water glycol system for heating the cofferdam spaces next to cargo tanks
when the vessel is loaded. What is the purpose of this heating system?

To maintain the temperature inside the space above 5 degrees C to protect the steel.

1054. What is the minimum requirement with respect to pressure relief valves on the cargo tanks of an LNG carrier
where the individual tanks are over 20 cubic metres capacity?

Two valves.

1055. What is the preferred method of accommodating expansion in cargo pipeline systems on LNG carriers?

Use expansion loops.

1056. What is the purpose of the "forcing vaporizer" found in some LNG carrier cargo plants?

To provide gas for burning in the boiler.

1057. When LNG is used as fuel a double wall piping system must be used in the engine room. What condition
should the annular space between the concentric pipes be maintained in when the fuel system is in service?

Filled with nitrogen at a pressure greater than the LNG fuel pressure.

1058. Which kind of cargo pumps are the most commonly used in cargo systems for LNG carriers?

Submerged electric motor pumps.

1059. Which line can be utilized to prevent line surge when starting the main pumps of a LNG carrier's cargo
system?

The condensate spray line.

1060. Which of the following insulation materials that are used in the cargo containment systems for LNG carriers
has the highest diffusion resistance?

Polyurethane foam.

1061. A chlorine carrier must be equipped with a chlorine absorption plant connected to the cargo tanks and cargo
lines. This requirement includes the provision of gas detectors for the spaces and areas around the cargo
containment system and the absorption plant outlet. What is the recommended setting for the visual and audible
alarms of the gas detectors?

5 ppm.

1062. Cargo heaters are frequently used when discharging refrigerated LPG cargoes into pressurised shore tanks.
What would be a typical "heating range" required from a heater for discharge of fully refrigerated propane?

From - 45 C to - 5 C.

1063. Cargo hoses intended for liquefied gas carriers have to be prototyped tested before being approved. When
new hoses of an already approved type are received onboard they also need to be pressure tested before being
put into service. What are the IMO Gas Code requirements for such hoses before they are put into service?

Not less than 1.5 times the specified maximum working pressure or more than two fifths of bursting pressure at
ambient temperature.
1064. LPG carriers rely heavily on the compressors fitted as part of the reliquefaction plant. Screw and
reciprocating types are widely used. Which type of reciprocating compressor is most common as a cargo
compressor?

Double acting, single stage, oil free compressor.

1065. Most reliquefaction plants on LPG carriers use a direct cooling system. Which of the statements given in the
options best describes a direct cooling cycle?

Cargo vapours are drawn off by a compressor, compressed, condensed than passed through an expansion valve
back to the tank.

1066. Some liquefied gas carriers are fitted with nitrogen generating equipment, often of the membrane module
design. What would be the expected purity of the nitrogen produced by such equipment?

95 to 97% pure nitrogen.

1067. The IMO Gas Codes require that all liquefied gas carrier cargo tanks are fitted with pressure relief valves.
Pilot operated relief valves are frequently used, particularly with refrigerated cargoes. What is the main advantage
of using pilot operated relief valves rather than simple spring loaded types for refrigerated liquefied gas cargoes
tanks?

They ensure accurate operation at the very low cargo carriage pressures.

1068. The reliquefaction plant for cargo cooling of liquefied gas cargoes can operate on either a direct or indirect
cycle. On which liquefied gas cargoes must indirect cycle cargo cooling plant be used according to the IMO Gas
Codes?

Cargoes such as chlorine, ethylene oxide and propylene oxide for which the vapours cannot be compressed due to
temperature restrictions.

1069. There are a number of standard reliquefaction plants commonly fitted onboard LPG and other liquefied gas
carriers. What type of reliquefaction plant is required for a cargo of Ethylene Oxide?

Indirect cycle.

1070. There are strict rules governing the placement and category of electrical equipment allowed in certain areas
of liquefied gas carriers. One such category is that of flameproof enclosures. What is a flameproof enclosure?

One which can withstand the pressure build-up during an internal ignition of a flammable mixture and is designed
to cool any flames occurring within the enclosure to below the ignition temperature.

1071. What is the main disadvantage of using oil free, screw type compressors for the reliquefaction plant of an
LPG carrier?

The compressor has to run at very high speeds to compensate for internal leakage.

1072. What is the purpose of an automatic shut-down system fitted onboard most liquefied gas carriers and how is
it initiated?

To prevent overfilling of the cargo tanks. It is initiated by a high level sensor in the cargo tank.

1073. What is the purpose of the purge gas condenser fitted to some liquefied gas carrier reliquefaction plants?

It is used to generate the cargo vapours required for purging the cargo tanks.
1074. When measuring the liquid level in the cargo tank of a liquefied gas carrier a number of different corrections
may be necessary to get a true reading. Why do readings obtained from a float type ullage tape sometimes require
a 'tape correction'?

The length of tape in contact with very cold cargo vapours may contract.

1075. Which type of reliquefaction plant can have the cooling coil placed directly in the vapour space of the cargo
tank?

One type of the indirect cycle reliquefaction plants.

1076. A ―Pellistor‖ is:

It is an electrical sensor unit fitted in a flammable gas detector for measuring hydrocarbon vapours and air
mixtures to determine whether the mixture is within the flammable range

1077. According to 33 CFR 156, for oil tankers trading in US waters, the minimum requirement for testing of cargo
transfer hoses and associated piping system are:

That no leakage occurs under static liquid pressure of at least 1.5 times the maximum allowable working pressure.

1078. After passing through the scrubbing tower of an inert gas system, the approximate level of carbon dioxide in
the inert flue gas should be:

13%

1079. An oil tanker with a defective Oil Discharge Monitoring Equipment may be allowed by a Port State Authority
to trade for:

One ballast voyage before proceeding to a repair port.

1080. An oil tanker's tank-cleaning machine with a rotational speed of 1 rpm and a selected pitch angle of 1.5
degrees is used to perform a bottom wash with a vertical angle from 40 degrees to 0 degrees for 1.5 cycles (3
passes). If the throughput of the machine at design pressure is 90 m3/hr, what will be the washing time and
quantity of crude oil required?

40 minutes and 60 cubic metres of oil.

1081. As per IMO requirements, the mechanical ventilation system of the cargo pump room shall be capable of
making:

At least 30 air changes per hour

1082. As per OPA 90 requirements, a vessel over 400 feet (121.9 metres) in length must carry oil spill clean-up gear
to be able to handle oil spillages of:

12 barrels (1.91 cubic metres).

1083. Fluid driven eductors operate on Bernoulli‘s principle, which states that:

The speed of a moving fluid increases as the pressure in the fluid decreases.

1084. Ship‘s cargo pump room alarm must be automatically activated when levels of hydrocarbon gas
concentration are:

No higher than 10% of LEL.


1085. The automatic stripping systems fitted on some of the centrifugal cargo pumps operate on the principle that:

If cargo vapour can be stopped from entering the cargo pump suction inlet, the flow will continue without
cavitation.

1086. The calibration of the ODME is carried with the use of:

Fresh water.

1087. The difference between the absolute pressure of a liquid at the inlet to a cargo pump and the vapour
pressure of the liquid is called the:

Net Positive Suction Head Available.

1088. The inert gas system shall be capable of delivering inert gas to the cargo tanks at the rate of:

At least 125% of the maximum discharge capacity.

1089. The typical amounts of sulphur dioxide gas in flue gas produced when burning high sulphur content fuels
would be:

2,000 ppm

1090. The usual pressure and vacuum levels at which the P/V valves on board an oil tanker are required to activate
are:

Pressure: 1 psi (0.069 bar) Vacuum: 0.5 psi (0.034 bar)

1091. When in-service testing a hose used for cargo transfer on an oil tanker (and for which the elongation of the
hose assembly when new was greater than 2.5%), the maximum permitted elongation before the hose must be
withdrawn from service should be:

Not more than 1.5 times the temporary elongation measured when the hose assembly was new, as documented
in the manufacturer's certificate.

1092. When tank cleaning hoses are tested for electrical continuity, they must display a reading of:

Not greater than 6 ohms per metre length.

1093. A decision support system for emergency management shall be provided on the navigation bridge. What
type of emergency situations shall as a minimum be identified in the emergency plans?

Fire, Damage to ship, Pollution, Unlawful acts threatening the safety of the ship and the security of its passenger
and crew, Pesonnel accidents, Cargo-related accidents, Emergency assistance to other ships

1094. Emergency instructions in appropriate languages shall be posted in passenger cabins. Which information
shall as a minimum be included in the emergency instructions?

The method of donning life-jackets, escape routes and alarm signals

1095. Here do you find detailed information and specific technical requirements for lifesaving appliances?

Life-Saving Apliance Code (LSA Code)

1096. How many lifejackets are required in a passenger cabin?

Same number as beds in the cabin


1097. How many rescue boats should be provided on passenger ships of 500 gross tons and above?

Two, one on each side of the ship

1098. How many two-way VHF radiotelephone apparatus shall be provided on board a passenger ship of 500 gross
tonnage and upwards?

1099. Is it required that the PA-system (Public Address) is connected to a back-up power sypply?

Yes, the public address system shall be connected to the emergency source of power

1100. Is it required to have supplementary emergency lighting on board passenger ships?

Yes, all passenger public spaces and alleyways shall be provided with supplementary electric lighting

1101. One water fog applicator is required for each pair of breathing apparatus on board which type of ship?

Passenger ships carrying more than 36 passengers

1102. Passenger ships have a normal requirement of 1 lifejacket per person + 10% for children. In addition to this,
how many lifejackets have to be stowed in conspicuous places on deck or at the muster stations?

5% extra

1103. Passenger ships shall either carry automatically self-righting liferafts or canopied reversible liferafts. What
does it mean that a liferaft is automatically self-righting?

The liferaft will automatically turn back into an upright position when it is empty of people

1104. What is the minimum number of independently driven fire pumps that must be provided on passenger ships
of 4000 tons gross tonnage and upwards?

1105. What is the minimum number of lifebuoys that shall be provided with self-igniting lights an self-activating
smoke signals?

1106. What is the name of this unit?

A hydrostatic release unit

1107. What is the purpose of an evacuation analysis?

To identify and eliminate, as far as practicable, congestion which may develop during an abandonment

1108. What is the time limit for abandonment of passenger ships?

30 minutes from the time the abandon ship signal is given

1109. Where do you find detailed information and specific technical requirements for fire safety systems?

Fire Safety Systems Code (FSS Code)

1110. Where shall you be able to activate the ship security alert system on board passenger ships?
From the navigation bridge and in at least one other location

1111. Which one of the listed requirements for passenger ships regarding personal lifesaving appliances do not
correspond to present regulations?

All lifejackets shall be fitted with a whistle, a light and a smoke signal

1112. As part of the decommissioning process for old reefer vessels they are sent to a recycling yard where any
refrigerant remaining in the refrigeration system is dealt with. Which one of the actions given in the options needs
to be carried out in preparation for delivery of a vessel to a recycling yard?

Make a careful note of the quantities of gas onboard and note this in the Ozone depletionrecord Book prior to
discharging the gas into recovery bottles.

1113. As well as having temperature sensors located in the cargo holds some reefer vessels are also fitted with
ethylene sensors. Why is it useful to have information regarding the ethylene content in a reefer vessel cargo hold
when carrying fruit cargoes?

Some fruit cargoes are sensitive to ethylene and the quality of the cargo can deteriorate as they may over-ripen.

1114. Data loggers are a vital part of the temperature control and monitoring system on a reefer vessel. In a
situation where the data logger fails several days before the end of the voyage it is still necessary to maintain
control of and monitor cargo temperatures. How could an accurate, portable thermometer be used to the best
effect, to achieve this, in such a situation?

Use the thermometer to check and control the delivery air temperature by inserting it in the delivery air ducting
close to the evaporators.

1115. Despite setting what appears to be the correct delivery air temperatures in accordance with shipper's
instructions, large cargo loss claims can still occur when operating reefer vessels. Which of the options given is
likely to help avoid the majority of these large claims?

By confirming the temperature scale that the shipper is using in his carriage instructions, Fahrenheit or Celsius.

1116. Many fruit cargoes are carried refrigerated and also under controlled atmosphere (CA) conditions. A
situation develops where there is a problem with the main reefer plant that will take several hours to repair but
the CA system is still operation. Which of the statements given in the options is the most accurate in these
circumstances?

The CA plant is only an adjunct for the refrigeration plant and therefore there should be concern about the
condition of the cargo.

1117. Many reefer vessels are fitted with controlled atmosphere systems (CA). There are a number of different
systems available but generally they all work by introducing nitrogen into the cargo space. Select, from the options
given, the main reason why nitrogen is generally the gas chosen for controlling the atmosphere in the cargo spaces
of a reefer vessel.

Nitrogen displaces the oxygen in the cargo space and allows the respiration of the fruit to be controlled.

1118. Most fruit cargoes carried under refrigeration require introduction of fresh air into the cargo space to
remove any excess carbon dioxide and ethylene produced by respiration of the cargo and sensors are fitted to
detect these gases. Shipper's instructions will often indicate 'constant air change' as a requirement for a cargo.
Why, even though this is a crude method for controlling the cargo space atmosphere, is this type of instruction
given?
Some cargoes are very sensitive to ethylene levels and it may be difficult to accurately measure the low levels that
would affect a cargo.

1119. On a conventional reefer vessel is possible to ventilate the cargo spaces with fresh air using fans and
trunkings. One of the reasons for using fresh air ventilation is to control the relative humidity within the cargo
space. Select the option which best completes the following statement. "It is beneficial to be able to control the
relative humidity within the cargo space because fruit cargoes should be kept…

…relatively moist to avoid the cargo dehydrating during the passage."

1120. On a reefer vessel air is passed over the cooling coils before entering the cargo hatch via trunking to cool the
cargo. It is important to ensure that the cooling coils are clear of any material such as plastic sheeting or bags. Why
is this so important?

The plastic may interfere with the air flow over the cooling coils and subsequently the cooling of the cargo.

1121. Prior to loading a reefer cargo it is good practise to carry out an 'ice test' of the temperature sensors within
the cargo space. Part of the test is to immerse the sensors in a test bucket of known temperature, usually zero
degrees Celsius as this is the melting point of ice. Which of the options is correct in relation to preparing the test
bucket?

Insulated ice buckets should be filled with ice cubes approximately 2 centimetres square and a small quantity of
distilled water to produce an icewater mixture. The ice cubes should be produced from clean distilled water.

1122. Refrigerated cargo spaces are fitted with temperature sensors and in some cases carbon dioxide sensors.
From the options given select the one which best completes the following statement. "Monitoring the carbon
dioxide content in a cargo space loaded with fruit can be useful because…

… increasing levels indicate that the fruit may be starting to ripen."

1123. Select the option which correctly completes the following statement. "A conventional reefer vessel operating
with a controlled atmosphere plant must have cargo spaces which…

… have a gas tight seal."

1124. The data logger on a reefer vessel normally records temperatures for air delivery, air return and cargo pulp.
How would the air delivery and return temperatures be expected to vary during the first few days of carrying a
cargo of citrus fruit which had not been pre-cooled before loading?

The difference between the two temperatures would steadily reduce.

1125. To correctly interpret the readings on the printout from a reefer vessel‘s cargo data logger it is essential to
have some knowledge of the location of the temperature sensors. Where would the temperature sensor for the
delivery air to a cargo hold be expected to be located?

In the air flow path from the cooling coils, about 3 metres from the coils.

1126. What should be done with the data logger printouts after completing the discharge of a refrigerated cargo?

They should be retained onboard for a minimum of 2 years.

1127. During sea passage on a roro vessel, how would you know if gasoline vapours were escaping from vehicles?

By using flammable gas detectors in the vehicle decks


1128. On a roro vessel, to what should you pay very close attention, when inspecting the structure and condition of
movable car decks?

Cracks in way of deck supports

1129. On a roro vessel, what additional securing arrangements should be used when loading a vehicle on an incline
or fixed Ramp

The Vehicle should also be chocked under its wheels

1130. On a roro vessel, what is Maximum Securing Load?

The load capacity of a device used to secure cargo on board

1131. On a roro vessel, what is the Maximum Securing Load of 'D' rings?

50% of the breaking strength

1132. On a roro vessel, what is the Maximum Securing Load of fibre ropes?

33% of the breaking strength

1133. On a roro vessel, what is the Maximum Securing Load of mild steel shackles?

50% of the breaking strength

1134. On a roro vessel, what is the Maximum Securing Load of reusable use wire ropes?

30% of the breaking strength

1135. On a roro vessel, what is the Maximum Securing Load of single use wire ropes?

80% of the breaking strength

1136. On a roro vessel, what is the Maximum Securing Load of web lashings?

50% of the breaking strength

1137. On a roro vessel, when should a trailer horse be taken out of service

If there is any damage to the wheel or spring, the frame is rusted or distorted or the pads are worn out

1138. On a roro vessel, where can you find the validity of web lashings

On the certificate supplied with the equipment

1139. On a roro vessel, where will escaping gasoline vapourssettle in a cargo hold? If the forced ventilation system
is shut down

At the lowest levels

1140. What must you ensure when using portable slopes to discharge ro-ro units?

They must be exactly aligned with the units' tyres

1141. When lowering a roro Cargo Side or Stern Ramp what must be ensured ?

The vessel is securely moored and there is nothing beneath the ramp
1142. A decision support system for emergency management shall be provided on the navigation bridge. What
type of emergency situations shall as a minimum be identified in the emergency plans?

Fire, Damage to ship, Pollution, Unlawful acts threatening the safety of the ship and the security of its passenger
and crew, Pesonnel accidents, Cargo-related accidents, Emergency assistance to other ships

1143. Emergency instructions in appropriate languages shall be posted in passenger cabins. Which information
shall as a minimum be included in the emergency instructions?

The method of donning life-jackets, escape routes and alarm signals

1144. How many lifejackets are required in a passenger cabin?

Same number as beds in the cabin

1145. How many rescue boats should be provided on ro-ro passenger ships of 500 gross tons and above?

Two, and at least one of the rescue boats shall be a Fast Rescue Boat

1146. How many two-way VHF radiotelephone apparatus shall be provided on board a ro-ro passenger ship of 500
gross tonnage and

upwards?

1147. Is it required that the PA-system (Public Address) is connected to a back-up power sypply?

Yes, the public address system shall be connected to the emergency source of power

1148. Is it required to have supplementary emergency lighting on board ro-ro ships?

Yes, all passenger public spaces and alleyways shall be provided with supplementary electric lighting

1149. Passenger ships have a normal requirement of 1 lifejacket per person + 10% for children. In addition to this,
how many lifejackets have to be stowed in conspicuous places on deck or at the muster stations?

5% extra

1150. Ro-ro passenger ships shall either carry automatically self-righting liferafts or canopied reversible liferafts.
What does it mean that a liferaft is automatically selfrighting?

The liferaft will automatically turn back into an upright position when it is empty of people

1151. What is the minimum number of independently driven fire pumps that must be provided on passenger ships
of 4000 tons gross tonnage and upwards?

1152. What is the minimum number of lifebuoys that shall be provided with self-igniting lights an self-activating
smoke signals?
2
1153. What is the purpose of an evacuation analysis?
To identify and eliminate, as far as practicable, congestion which may develop during an abandonment
1154. What is the time limit for abandonment of ro-ro passenger ships?
30 minutes from the time the abandon ship signal is given
1155. What is this?
A hydrostatic release unit
1156. Where do you find detailed information and specific technical requirements for fire safety systems?
Fire Safety Systems Code (FSS Code)
1157. Where do you find detailed information and specific technical requirements for lifesaving appliances?
Life-Saving Apliance Code (LSA Code)
1158. Where shall you be able to activate the ship security alert system on board ro-ro passenger ships?
From the navigation bridge and in at least one other location
1159. Which one of the listed requirements for passenger ships regarding personal lifesaving appliances do not
correspond to present regulations?
All lifejackets shall be fitted with a whistle, a light and a smoke signal
12. Bulk liquid cargoes carried in flexi-tank containers are considered dangerous:
When the associated material safety data sheet shows a constituent(s)
listed in the IMDG Code.

13. What must be ensured, prior to receiving a bulk cargo of iron ore on a Bulk
Carrier?
Cargo hold bilge suctions must be satisfactorily tested

14. During a pre-loading survey prior to loading grain on a Bulk Carrier, very small
amount of the previous grain cargo is found in a cargo hold; what is the significance
of this situation?
The vessel may fail the pre-load survey and be declared off-hire

15. Which special regulations cover transportation of solid Bulk cargoes?


IMO Bulk Cargoes Code (BC) and the IMO International Maritime Solid
Bulk Cargo Code( IMSBC)

16. How should mild steel slabs be loaded in a bulk carrier?


Interlocked across the entire cargo hold with the longitudinal axes
athwartships

17. On multi-purpose vessels, responsibility for the stowage and securing of


containers is:
Determined by the clauses of the charter-party.

18. What is the possible concern if fuel tanks on a Bulk Carrier, which are close to
cargo spaces containing grain, are excessively heated?
The grain cargo may be heated and damaged

19. What governs the disposal of dry bulk cargo residues at sea?
MARPOL regulations

20. What could happen if a bulk vessel failed to display placards notifying the crew of
the disposal of garbage within and outside Special Areas?
The vessel could be detained by port state control authorities

21. What publication must be carried on a vessel carrying dry bulk cargoes?
IMO Solid Bulk cargo Code or IMO Solid Bulk?

22. What is the purpose of a draught survey before and after loading on a Bulk Carrier?
To ascertain the actual weight of cargo loaded

23. A container vessel has lost several dangerous goods containers overboard. The
master must report this loss of container incident to:
The nearest Coastal state.

24. Best location to stow containers loaded with Calcium Hypochlorite would be:
On deck, away from sources of heat.
25. A bulk cargo is loaded and the cargo stow has been left with an
excessive peak height; what could be the result of this situation?
Excessive stresses on tank top

26. When considering how to deal with cargo residues during hatch
cleaning at sea on a Bulk Carrier, what is the most careful
consideration?
Consult MARPOL handbook and the vessels Safety
Management System (SMS) for guidance

27. Why is air draught an important consideration when loading bulk


cargoes on Bulk Carriers?
Because of movement of the bulk cargo loader or unloaders

28. Besides normal loads, the lashings of the containers stowed at the
outboard part of the deck stow are additionally subjected to:
The effect of wind on the containers.

29. What measures should be taken in order to avoid flammable


gases forming on top of coal cargoes on a Bulk Carrier?
Ventilation to be carried out as indicated in the IMO
solid Bulk Cargo Code

30. Which special regulations cover transportation of grain on a Bulk Carrier?


IMO Grain Rules?

You might also like