Rayat Shikshan Sanstha’s

KARMAVEER BHAURAO PATIL

POLYTECHNIC,
SATARA

Control System and PLC

Department Of Electronics And Telecommunication Engineering
 Control System and PLC
EJ5G Subject Code: 17536 Third Year Entc

Amit Nevase
Lecturer,
Department of Electronics & Telecommunication Engineering,
Karmaveer Bhaurao Patil Polytechnic, Satara

6/30/2016 Amit Nevase 2

 Objectives

The student will be able to:

 Understand classifications of control system.

 Understand Steady state, time response, and frequency

response analysis.

 Analyze the Stability of control system using RH criteria.

 Understand the fundamentals and diff. Hardware parts of

PLC.

 Draw ladder diagrams to program PLC

6/30/2016 Amit Nevase 3
 Teaching & Examination Scheme

Teaching Scheme Examination Scheme

PAPER
TH TU PR TH PR OR TW TOTAL
HRS

03 -- 02 03 100 50# --- 25@ 175

 Two tests each of 25 marks to be conducted as per the schedule given by

MSBTE.
 Total of tests marks for all theory subjects are to be converted out of 50 and
to be entered in mark sheet under the head Sessional Work (SW).

6/30/2016 Amit Nevase 4

 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 5
 Module II – Time Response Analysis
 Time Domain Analysis (4 Marks)
 Transient and Steady State Response
 Standard Test Inputs : Step, Ramp, Parabolic and Impulse, Need, Significance
and corresponding Laplace Representation
 Poles and Zeros : Definition, S-plane representation
 First and Second order Control System (8 Marks)
 First Order Control System : Analysis for step Input, Concept of Time Constant
 Second Order Control System : Analysis for step input, Concept, Definition and
effect of damping
 Time Response Specifications (8 Marks)
 Time Response Specifications ( no derivations )
 Tp, Ts, Tr, Td, Mp, ess – problems on time response specifications
 Steady State Analysis – Type 0, 1, 2 system, steady state error constants,
problems

6/30/2016 Amit Nevase 6

 Module III – Stability

 Introduction to Stability (4 Marks)

 Definition of Stability, Analysis of stable, unstable, critically stable
and conditionally stable
 Relative Stability
 Root locations in S-plane for stable and unstable system

 Routh’s Stability Criterion (8 Marks)

 Routh’s Stability Criterion : Different cases and conditions
 Statement Method
 Numericals Problems

6/30/2016 Amit Nevase 7

 Module IV – Control Actions

 Process Control System (4 Marks)

 Process Control System – Block diagram, explanation of each block

 Control Actions (8 Marks)

 Discontinuous Mode : On-Off Controller, Equation, Neutral Zone
 Continuous modes: Proportional Controller (offset, proportional
band), Integral Controllers, Derivative Controllers – output
equations, corresponding Laplace transforms, Response of P, I, D
controllers
 Composite Controllers : PI, PD, PID Controllers – output equations,
response, comparison

6/30/2016 Amit Nevase 8

 Module V – PLC Fundamentals
 Introduction (4 Marks)
 Evolution of PLC in automation, need and benefits of PLC in
automation
 Block Diagram of PLC (12 Marks)
 Block diagram and description of different parts of PLC -
 CPU Function, Scanning cycle, speed of execution, Power supply
function,
 Memory – function , organization of ROM and RAM
 Input modules – function, different input devices used with PLC
and their uses
 Output modules – function, different output devices used with
PLC and their uses
 Fixed and Modular PLCs
6/30/2016 Amit Nevase 9
 Module VI – PLC Hardware and Programming
 PLC Hardware (8 Marks)
 Discrete Input Modules – Block diagram, typical wiring details, Specifications of
AC input modules and DC input modules. Sinking and sourcing concept in DC
input modules
 Discrete Output Modules – Block diagram, typical wiring details, Specifications
of AC output modules and DC output modules.
 Analog Input and output modules : Block diagram, typical wiring details and
specifications
 PLC Programming (16 Marks)
 I/O Addressing in PLC
 PLC Instruction Set : Relay instructions, timer instructions, counter instructions,
data handling instructions, logical and comparison instructions
 PLC programming examples based on above instruction using Ladder
programming

6/30/2016 Amit Nevase 10

 Module-I
Introduction to Control
System

6/30/2016 Amit Nevase 11

 Specific Objectives

Explain different types of control system

Develop transfer functions

Differentiate between 1st& 2nd order of system

Develop and solve block diagram of control

system

6/30/2016 Amit Nevase 12

 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 13
Input

Input

 The stimulus or excitation applied to a control system

from an external source in order to produce the
output is called input

6/30/2016 Amit Nevase 14

Output

Input Output

 The actual response obtained from a system is

called output.

6/30/2016 Amit Nevase 15

“System”

Input Output
SYSTEM

 A system is an arrangement of or a combination of

different physical components connected or related in
such a manner so as to form an entire unit to attain a
certain objective.

6/30/2016 Amit Nevase 16

Control

 It means to regulate, direct or command a system so

that the desired objective is attained

6/30/2016 Amit Nevase 17

 Combining above definitions

System + Control = Control System

6/30/2016 Amit Nevase 18

Control System

Input Output
CONTROL
SYSTEM

 It is an arrangement of different physical elements

connected in such a manner so as to regulate, direct
or command itself to achieve a certain objective.

6/30/2016 Amit Nevase 19

 Difference between System and Control System

Input Proper Input Control Desired

System System
Output Output

(May or may not

be desired)

6/30/2016 Amit Nevase 20

Difference between System and Control System

An example : Fan

230V/50Hz Fan Air Flow

Input Output
(System)
AC Supply

6/30/2016 Amit Nevase 21

A Fan: Can't Say System

 A Fan without blades cannot be a “SYSTEM”

Because it cannot provide a desired/proper output
i.e. airflow

Input Output

230V/50Hz No Airflow

AC Supply (No Proper/ Desired

Output)

6/30/2016 Amit Nevase 22

A Fan: Can be a System

 A Fan with blades but without regulator can be a “SYSTEM”

Because it can provide a proper output i.e. airflow
 But it cannot be a “Control System” Because it cannot
provide desired output i.e. controlled airflow

Input Output

230V/50Hz Airflow

AC Supply (Proper Output)

6/30/2016 Amit Nevase 23

 A Fan: Can be a Control System

 A Fan with blades and with regulator can be a “CONTROL

SYSTEM” Because it can provide a Desired output.
i.e. Controlled airflow

Control
Input Output
Element

230V/50Hz Controlled Airflow

AC Supply (Desired Output)

6/30/2016 Amit Nevase 24

 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 25
 Classification of Control System

Classification of Control System

(Depending on control action)

Open Loop Control Closed Loop Control

System System

6/30/2016 Amit Nevase 26

 Open Loop Control System
Definition:

“A system in which the control action is totally

independent of the output of the system is called as open
loop system”

Controlled
Reference I/p Controller Process o/p

r(t) u(t) c(t)

Fig. Block Diagram of Open loop Control System

6/30/2016 Amit Nevase 27
OLCS Examples

 Electric hand drier – Hot

air (output) comes out as
long as you keep your
hand under the machine,
irrespective of how much
your hand is dried.

6/30/2016 Amit Nevase 28

OLCS Examples

 Automatic washing machine

– This machine runs
according to the pre-set time
irrespective of washing is
completed or not.

6/30/2016 Amit Nevase 29

OLCS Examples

 Bread toaster - This

machine runs as per
adjusted time
irrespective of toasting is
completed or not.

6/30/2016 Amit Nevase 30

OLCS Examples

 Automatic tea/coffee
Vending Machine –
These machines also
function for pre adjusted
time only.

6/30/2016 Amit Nevase 31

OLCS Examples

 Light switch – lamps glow whenever light switch is on

irrespective of light is required or not.

 Volume on stereo system – Volume is adjusted

manually irrespective of output volume level.

6/30/2016 Amit Nevase 32

Advantages of OLCS

 Simple in construction and design.

 Economical.

 Easy to maintain.

 Generally stable.

 Convenient to use as output is difficult to measure.

6/30/2016 Amit Nevase 33

Disadvantages of OLCS

 They are inaccurate

 They are unreliable

 Any change in output cannot be corrected

automatically.

6/30/2016 Amit Nevase 34

Closed Loop System

Definition:

“A system in which the control action is somehow

dependent on the output is called as closed loop system”

6/30/2016 Amit Nevase 35

 Block Diagram of CLCS

Forward Path

Command Error Manipulated

Controlled
I/p Signal Signal
O/p
Reference r(t) Controller Plant
Transducer c(t)
e(t) m(t)

Reference
I/p

Feedback
Feedback b(t) c(t)
Transducer
Signal

Feedback Path
6/30/2016 Amit Nevase 36
CLCS Examples

 Automatic Electric Iron- Heating elements are

controlled by output temperature of the iron.

6/30/2016 Amit Nevase 37

CLCS Examples

Servo voltage stabilizer – Voltage controller

operates depending upon output voltage of the
system.

6/30/2016 Amit Nevase 38

CLCS Examples

Perspiration

6/30/2016 Amit Nevase 39

Advantages of CLCS

 Closed loop control systems are more accurate even in the

presence of non-linearity.
 Highly accurate as any error arising is corrected due to
presence of feedback signal.
 Bandwidth range is large.
 Facilitates automation.
 The sensitivity of system may be made small to make
system more stable.
 This system is less affected by noise.
6/30/2016 Amit Nevase 40
Disadvantages of CLCS

 They are costlier.

 They are complicated to design.

 Required more maintenance.

 Feedback leads to oscillatory response.

 Overall gain is reduced due to presence of feedback.

 Stability is the major problem and more care is needed

to design a stable closed loop system.

6/30/2016 Amit Nevase 41

Difference Between OLCS & CLCS
Open Loop Control System Closed Loop Control System

1. The open loop systems 1. The closed loop systems

are simple & economical. are complex and costlier
2. They consume less 2. They consume more
power. power.
3. The OL systems are 3. The CL systems are not
easier to construct easy to construct because
because of less number of more number of
of components required. components required.
4. The open loop systems 4. The closed loop systems
are inaccurate & are accurate & more
unreliable reliable.

6/30/2016 Amit Nevase 42

Difference Between OLCS & CLCS
Open Loop Control System Closed Loop Control System

5. Stability is not a major 5. Stability is a major problem

problem in OL control in closed loop systems & more
systems. Generally OL care is needed to design a
systems are stable. stable closed loop system.
6. Small bandwidth. 6. Large bandwidth.
7. Feedback element is 7. Feedback element is
absent. present.
8. Output measurement is 8. Output measurement is
not necessary. necessary.
6/30/2016 Amit Nevase 43
Difference Between OLCS & CLCS
Open Loop Control System Closed Loop Control System

9. The changes in the output due 9.The changes in the output

to external disturbances are not due to external disturbances
corrected automatically. So they are corrected automatically. So
are more sensitive to noise and they are less sensitive to noise
other disturbances. and other disturbances.

10. Examples: 10. Examples:

Coffee Maker, Guided Missile,

Automatic Toaster, Temp control of oven,

Hand Drier. Servo voltage stabilizer.

6/30/2016 Amit Nevase 44
 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 45
Classification of Control System

Classification of Control System

Linear Control Non-linear Control

System System

6/30/2016 Amit Nevase 46

Linear Control System

When an input X1 produces an output Y1 & an

input X2 produces an output Y2, then any
combination  X 1   X 2 should produce an
output Y1   Y 2 . In such case system is linear.
Therefore, linear systems are those where the
principles of superposition and proportionality
are obeyed.

6/30/2016 Amit Nevase 47

Non-linear Control System

 Non-linear systems do not obey law of superposition.

 The stability of non-linear systems depends on root

location as well as initial conditions & type of input.

 Non-linear systems exhibit self sustained oscillations

of fixed frequency.

6/30/2016 Amit Nevase 48

Difference Between Linear & Non-linear System

Linear System Non-linear System

1. Obey superposition. 1. Do not obey superposition

2. Can be analyzed by standard 2. Cannot be analyzed by standard
test signals test signals
3. Stability depends only on 3. Stability depends on root
root location locations, initial conditions &
type of input
4. Do not exhibit limit cycles 4. Exhibits limit cycles
5. Do not exhibit hysteresis/ 5. Exhibits hysteresis/ jump
jump resonance resonance
6. Can be analyzed by Laplace 6. Cannot be analyzed by Laplace
transform, z- transform transform, z- transform

6/30/2016 Amit Nevase 49

Classification of Control System

Classification of Control System

Time Varying Time Invarying Control

Control System System

6/30/2016 Amit Nevase 50

Time varying/In-varying Control System

 Systems whose parameters vary with time are called

time varying control systems.

 When parameters do not vary with time are called

Time Invariant control systems.

6/30/2016 Amit Nevase 51

Time varying/In-varying Control System

The mass of missile/rocket reduces as fuel is

burnt and hence the parameter mass is time

varying and the control system is time varying

type.

6/30/2016 Amit Nevase 52

 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 53
Servo System

 Definition:

1. Servo system is defined as automatic feedback control

system working on error signals giving the output as
mechanical position, velocity or acceleration.

2. Servo system is one type of feedback control system in

which control variable is the mechanical load position &
its time derivatives like velocity and acceleration.

6/30/2016 Amit Nevase 54

General block diagram of Servo System

6/30/2016 Amit Nevase 55

Difference between Servo System

AC servo System DC servo System

1. Efficiency is low 1. Efficiency is high

2. Low power output 2. High power output
3. It requires less 3. It requires frequent
maintenance maintenance
4. Less stability 4. More stability
problems problems
5. Smooth operation 5. Noisy operation
6. It has non-linear 6. It has linear
characteristics characteristics
6/30/2016 Amit Nevase 56
DC Servo System

6/30/2016 Amit Nevase 57

DC Servo System

Working of Servo System

6/30/2016 Amit Nevase 58

 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 59
 Laplace Transform

 Developed mathematics in The French Newton

astronomy, physics, and statistics Pierre-Simon Laplace

 Began work in calculus which led

to the Laplace Transform

 Focused later on celestial

mechanics

 One of the first scientists to

suggest the existence of black
holes

6/30/2016 Amit Nevase 60

Laplace Transform

 To evaluate the performance of an automatic control

system commonly used mathematical tool is “Laplace
Transform”

 Laplace transform converts the differential equation

into an algebraic equation in ‘s’.

 Laplace transform exist for almost all signals of

practical interest.

6/30/2016 Amit Nevase 61

Why Laplace Transform?
Laplace
Transformation

Time domain Frequency domain

unknown f(t), d/dt, Diff Eqs unknown F(s), Alg Eqs

Solve
Differential Solve
Equations Algebraic
Equations

Time domain Frequency domain

known f(t) known F(s)

Inverse
Laplace
Transform
6/30/2016 Amit Nevase 62
Advantages of Laplace Transform

 Solution of intego differential equation of time

systems can be easily obtained.

 Initial conditions are automatically incorporated.

 Laplace transform provides an easy & effective

solution of many problems arising in automatic control
systems.

 Laplace transform allows the use of graphical

techniques, for predicting the system performance.
6/30/2016 Amit Nevase 63
Laplace Transform- Definition

The Laplace transform of a function, f(t), is defined as


F ( s )  L  f (t )    f  t  e  st dt (1-1)
0

where F(s) is the symbol for the Laplace transform, L is the Laplace
transform operator, and f(t) is some function of time, t.

Note: The L operator transforms a time domain function f(t)

into an s domain function, F(s). s is a complex variable:
s = a + bj, j B 1

6/30/2016 Amit Nevase 64

Standard Laplace Transform
f (t ) F ( s)  L[ f (t )]
1 or u(t ) 1
s
e  t 1
s 
sin t 
s 2
2

cost s
s2   2
e  t sin  t 
(s   )2   2
e t cos  t s 
(s   )2   2
t 1
s2
tn n!
s n 1
e  t t n n!
( s   ) n 1
 (t ) 1

*Use when roots are complex.

6/30/2016 Amit Nevase 65

Inverse Laplace Transform

By definition, the inverse Laplace transform operator, L-1,

converts an s-domain function back to the corresponding
time domain function:

f  t   L  F  s  
1

6/30/2016 Amit Nevase 66

 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 67
Transfer Function

 The relationship between input & output of a system is

given by the transfer function.

 Definition: The ratio of Laplace transform of the output

to the Laplace transform of the input under the

assumption of zero initial conditions is defined as

“Transfer Function”.

6/30/2016 Amit Nevase 68

Transfer Function

LT
System c(t) System C(s)
r(t) R(s)
g(t) G(s)

For the system shown,

c(t)= output L{c(t)}= C(s)
r(t)= input L{r(t)}= R(s)
g(t)= System function L{g(t)}= G(s)

Therefore transfer function G(s) for above system is given by,

Laplace of output C (s)

G(s)= = R(s)
Laplace of input

6/30/2016 Amit Nevase 69

 Transfer Function of closed loop system
Error Gain for CL system is given by;
Signal
C( s)
R(s) E(s) G( s) 
G(s) C(s) E( s)
+-
Output  C ( s)  G (s).E(s)      (3)
Input
Substitute value of E(s) from eq. 1 to 3
B(s) H(s) C( s)  G ( s).(R( s)  B(s))
 C ( s)  G ( s).R(s)  G( s).B( s)      (4)
Feedback
Signal
Substitute value of B(s) from eq. 2 to 4
Error signal is given by;
C ( s)  G (s) R(s)  G(s).H(s).C(s)
E ( s )  R ( s )  B( s )      (1) G(s).R(s)  C(s)  G(s).H(s).C(s)
 R(s)  E ( s)  B( s)
G(s).R(s)  C(s)(1  G(s).H(s))
Gain of feedback network is given by; Transfer function is given by;
B( s )
H ( s)  C (s) G (s)
C ( s) 
T.F.= R( s ) 1  G ( s ).H(s)
 B( s)  H (s).C(s)      (2)
6/30/2016 Amit Nevase 70
Laplace Transform of Passive Element (R,L & C)

 The Laplace transform can be used independently on

different circuit elements, and then the circuit can be

solved entirely in the S Domain (Which is much easier).

 Let's take a look at some of the circuit elements

6/30/2016 Amit Nevase 71

Laplace Transform of R

 Resistors are time and frequency invariant. Therefore,

the transform of a resistor is the same as the
resistance of the resistor.

L{Resistor}=R(s)

6/30/2016 Amit Nevase 72

Laplace Transform of C

Let us look at the relationship between voltage, current,

and capacitance, in the time domain:
dv(t)
i (t )  C
dt
Solving for voltage, we get the following integral:

1
v(t)   i(t) dt
C to
Then, transforming this equation into the Laplace
domain, we get the following:
11
V (s)  I (s)
6/30/2016
C s Amit Nevase 73
Laplace Transform of C

Again, if we solve for the ratio V(s)/I(s), we get the following:

V (s) 1

I (s) sC

Therefore, the transform for a capacitor with

capacitance C is given by:

1
L{capacitor} 
sC

6/30/2016 Amit Nevase 74

Laplace Transform of L

Let us look at the relationship between voltage, current,

and inductance, in the time domain:

di(t)
v(t)  L
dt
putting this into the Laplace domain, we get the
formula:

V (s)  sLI(s)
And solving for our ratio
V (s)
 sL
I(s)
6/30/2016 Amit Nevase 75
Laplace Transform of L

Therefore, the transform of an inductor with inductance

L is given by:

L{inductor}  sL

6/30/2016 Amit Nevase 76

 Transfer Function of RC and RLC electrical circuits

Example: Find the TF of given RC network

Taking Laplace transform above equation

C 1
Vi(t) i(t) Vo(t) Vo(s)  I (s)      (2)
sC

 I (s)  sC.Vo(s)      (3)

Apply KVL for input loop, From equation 1,
t 1
1 Vi(s)  I (s)(R  )      (4)
vi(t)  Ri(t)   i(t)dt sC
C0 From equation 3 and 4,
Taking Laplace transform above equation
1 1
Vi(s)  RI(s)  I (s)      (1) Vi(s)  Vo(s).sC.(R  )
sC sC
Apply KVL for output loop,
t
1
6/30/2016 C 
vo (t)  i (t)dt Amit Nevase 77
0
 Vo(s) 1
Transfer Function= G(s)= 
Vi(s) 1
sC.(R  )
sC

Vo(s) 1

Vi(s) sCR  1
sC.( )
sC

Vo(s) 1

Vi(s) sCR  1

Vi(s) 1 Vo(s)
sCR  1
6/30/2016 Amit Nevase 78
 Transfer Function of RC and RLC electrical circuits

Example: Find the TF of given RLC network

L
Apply KVL for input loop,
C
Vi(t) i(t) Vo(t)
1
Vi(s)  RI(s)  sLI(s)  I (s)
sC

Taking Laplace transform above network 1

Vi(s)  [R  sL ]I (s)        (1)
sL
sC

Apply KVL for output loop,

1
Vi(s) I(s) Vo(s) 1
sC Vo(s)  I (s)      (2)
sC

6/30/2016 Amit Nevase 79

From equation 1 and 2, 1
I (s)
Vo(s)
Transfer Function= Vi (s)
 sC
1
[R  sL ] I(s)
sC

1
 sC
1
[R  sL  ]
sC

1
 sC
sCR  s 2 LC  1
sC

1

sCR  s 2 LC  1

1
 2
6/30/2016 Amit Nevase s LC  sCR  1 80
 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 81
Order of System

 The order of control system is defined as the highest

power of s present in denominator of closed loop
transfer function G(s) of unity feedback system.

6/30/2016 Amit Nevase 82

Example1: Determine order of given system

s(s 2)
TF  G(s)  4
s  7s3  10s 2  5s  5

6/30/2016 Amit Nevase 83

Example1: Determine order of given system

s(s 2)
TF  G(s)  4
s  7s3  10s 2  5s  5

Answer: The highest power of equation in denominator

of given transfer function is ‘4’.
Hence the order of given system is fourth

6/30/2016 Amit Nevase 84

System Order and Proper System

 Highest power of s present in denominator of closed

loop transfer function is called as “Order of System”.

 A proper system is a system where the degree of the

denominator is larger than or equal to the degree of

the numerator polynomial.

6/30/2016 Amit Nevase 85

Example 2 : Determine order of given system
(s  5)(s  2)
G (s) 
s (s  3)(s  4)

6/30/2016 Amit Nevase 86

Example 2 : Determine order of given system
(s  5)(s  2)
G (s) 
s (s  3)(s  4)

Solution: To obtain highest power of denominator,

Simplify denominator polynomial.
s(s 3)(s 4)  0
s(s 2  7 s 12)  0

s3  7s2  12s  0

The highest power of equation in denominator of given transfer

function is ‘3’. Hence given system is “Third Order system”.
The degree of denominator is larger than the numerator hence
system is “Proper System”
6/30/2016 Amit Nevase 87
Example 3 : Determine order of given system
K(s  5)
G (s)  3
s (7 s 2  12s  5)

6/30/2016 Amit Nevase 88

Example 3 : Determine order of given system
K(s  5)
G (s)  3
s (7 s 2  12s  5)

Solution: To obtain highest power of denominator,

Simplify denominator polynomial.

s3 (7s 2  12s  5)  0

7s  12s  5s  0
5 4 3

The highest power of equation in denominator of given transfer

function is ‘5’. Hence given system is “Fifth Order system”.
The degree of denominator is larger than the numerator hence
system is “Proper System”
6/30/2016 Amit Nevase 89
Types of System

(depending on highest power of denominator)

 Zero (0) Order System

 First Order System

 Second Order System

6/30/2016 Amit Nevase 90

Zero (0) Order System

Definition: If highest power of complex variable ‘s’ present

in Characteristics equation is zero, then it is called as
“Zero order System”

R(s) + 1 C(s)
1 T
-

6/30/2016 Amit Nevase 91

Zero (0) Order System

Consider a unity feedback system with transfer function

1
G (s) 
1 T
Hence characteristics equation is given by,
1 T  0
or
1  s 0T  0
Here the highest power of s is equal to 0,
Hence the system given above is zero order system.

Practical Example: Amplifier type control system

6/30/2016 Amit Nevase 92
First Order System

Definition: If highest power of complex variable ‘s’ present

In Characteristics equation is one, then it is called as
“First order System”

+ 1 C(s)
R(s)
1  sCR
-

6/30/2016 Amit Nevase 93

First Order System

Consider a unity feedback system with transfer function

1
G (s) 
1  sCR
Hence characteristics equation is given by,
1  sCR  0
Here the highest power of s is equal to 1,
Hence the system given above is First order system.

Practical Example: RC circuits, thermal type systems

6/30/2016 Amit Nevase 94

Second Order System

Definition: If highest power of complex variable ‘s’ present

In Characteristics equation is two, then it is called as
“Second order System”

R(s) + 1 C(s)
s 2 LC  sCR  1
-

6/30/2016 Amit Nevase 95

Second Order System

Consider a unity feedback system with transfer function

1
G (s) 
s 2 LC  sCR  1
Hence characteristics equation is given by,
s 2 LC  sCR  1  0

Here the highest power of s is equal to 2,

Hence the system given above is Second order system.

Practical Example: RLC circuits, Robotic control system.

6/30/2016 Amit Nevase 96

 Module I – Introduction to Control System
 Introduction to Control systems (4 Marks)
 Control System – Definition and Practical Examples
 Classification of Control System : Open Loop and Closed Loop Systems –
Definitions, Block diagrams, practical examples, and Comparison, Linear and
Non-linear Control System, Time Varying and Time In-varying Systems
 Servo System : Definition, Block Diagram, Classification (AC and DC Servo
System), Block diagram of DC Servo System.
 Laplace Transform and Transfer Function (4 Marks)
 Laplace Transform : Signifiance in Control System
 Transfer Function : Definition, Derivation of transfer functions for Closed loop
Control System and Open Loop Control System, Differential Equations and
transfer functions of RC and RLC Circuit
 Block Diagram Algebra (8 Marks)
 Order of a System : Definition, 0,1,2 order system Standard equation, Practical
Examples
 Block Diagram Reduction Technique: Need, Reduction Rules, Problems
6/30/2016 Amit Nevase 97
Need of Block Diagram Algebra

 If the system is simple & has limited parameters then it

is easy to analyze such systems using the methods

discussed earlier i.e. transfer function, if the system is

complicated and also have number of parameters then

it is very difficult to analyze it.

6/30/2016 Amit Nevase 98

Need of Block Diagram Algebra

 To overcome this problem block diagram

representation method is used.

 It is a simple way to represent any practically

complicated system. In this each component of the
system is represented by a separate block known as
functional block.

 These blocks are interconnected in a proper sequence.

6/30/2016 Amit Nevase 99

Block Diagram Fundamentals

 Block Diagram: It is shorthand, pictorial representation

of the cause and effect relationship between input and

output of a physical system.

Input Output
BLOCK

6/30/2016 Amit Nevase 100

Block Diagram Fundamentals

 Output: The value of the input is multiplied to the

value of block gain to get the output.

X(s) Y(s)
3s

Output Y(s)= 3s. X(s)

6/30/2016 Amit Nevase 101
Block Diagram Fundamentals

 Summing Point: Two or more signals can be added/

substracted at summing point.

y
+
x output
+
Output =x+y-z

-
z

6/30/2016 Amit Nevase 102

Block Diagram Fundamentals

 Take off Point: The output signal can be applied to two

or more points from a take off point.

Z Z

Take off point

6/30/2016 Z Amit Nevase 103
Block Diagram Fundamentals
 Forward Path: The direction of flow of signal is from input
to output
Forward Path

R(s) + G1 G2
C(s)

H1

Feedback Path
 Feedback Path: The direction of flow of signal is from
output to input
6/30/2016 Amit Nevase 104
 Block Diagram Reduction Techniques

Rule 1: For blocks in cascade

Gain of blocks connected in cascade gets
multiplied with each other.

R(s) C(s)
R(s) G1 R1(s) G2 C(s) G1G2

R1(s)=G1R(s)
C(s)= G1G2R(s)
C(s) =G2R1(s)
=G1G2R(s)

6/30/2016 Amit Nevase 105

R(s) G1 G2 G3 C(s)

Find Equivalent

R(s) G1G2G3 C(s)

6/30/2016 Amit Nevase 106

 R(s) G1 G2 G3 C(s)

R1(s)

Find Equivalent

R(s)
G1G2G3
C(s) R(s) G1G2 G3 C(s)

R1(s)
6/30/2016 Amit Nevase 107
 Block Diagram Reduction Techniques
Rule 2: For blocks in Parallel
Gain of blocks connected in parallel gets added
algebraically.
R1(s)
G1
+
R(s) R2(s) - C(s) R(s) G1-G2+G3 C(s)
G2
+
R3(s)
G3

C(s)= R1(s)-R2(s)+R3(s) C(s)= (G1-G2+G3) R(s)

= G1R(s)-G2R(s)+G3R(s)
C(s)=(G1-G2+G3) R(s)
6/30/2016 Amit Nevase 108
 Block Diagram Reduction Techniques

Rule 3: Eliminate Feedback Loop

R(s)
E(s) G C(s)
+- R(s) G C(s)
+
1  GH

B(s) H

C(s) G
 In General
R (s) 1  GH

6/30/2016 Amit Nevase 109

 From Shown Figure,

E (s)  R(s)  B(s)

and
R(s) C (s)  G.E (s)
E(s) C(s)
+- G  G[R(s)  B(s)]
 GR(s)  GB(s)
But
B(s) B(s)  H .C (s)
H
 C (s)  G.R(s)  G.H.C(s)

C (s)  G.H  GR(s)

 C (s){1  G.H}  G.R(s)

C ( s) G
For Negative Feedback  
R( s ) 1  GH
6/30/2016 Amit Nevase 110
 From Shown Figure,
E (s)  R(s)  B(s)
and
R(s) C (s)  G.E (s)
E(s) C(s)
+ G  G[R(s)  B(s)]
+
 GR(s)  GB(s)
But
B(s) B(s)  H .C (s)
H
 C (s)  G.R(s)  G.H.C(s)

C (s)  G.H  GR(s)

 C (s){1  G.H}  G.R(s)

C ( s) G
For Positive Feedback  
R( s) 1  GH
6/30/2016 Amit Nevase 111
 Block Diagram Reduction Techniques

Rule 4: Associative Law for Summing Points

The order of summing points can be changed if two or more
summing points are in series

R(s) + X + C(s) R(s) + X + C(s)

- -
B1 B2 B2 B1

X=R(s)-B1 X=R(s)-B2
C(s)=X-B2 C(s)=X-B1
C(s)=R(s)-B1-B2 C(s)=R(s)-B2-B1
6/30/2016 Amit Nevase 112
 Block Diagram Reduction Techniques

Rule 5: Shift summing point before block

R(s) + C(s) R(s) + C(s)

G G
+ +
X 1/G

C(s)=R(s)G+X
C(s)=G{R(s)+X/G}
=GR(s)+X

6/30/2016 Amit Nevase 113

 Block Diagram Reduction Techniques

Rule 6: Shift summing point after block

R(s) + C(s) R(s) + C(s)

G G
+ +

X G
X

C(s)=G{R(s)+X} C(s)=GR(s)+XG
=GR(s)+GX =GR(s)+XG
6/30/2016 Amit Nevase 114
 Block Diagram Reduction Techniques

Rule 7: Shift a take off point before block

R(s) C(s) R(s) C(s)

G G

G
X
X

C(s)=GR(s) C(s)=GR(s)
and and
X=C(s)=GR(s) X=GR(s)
6/30/2016 Amit Nevase 115
 Block Diagram Reduction Techniques

Rule 8: Shift a take off point after block

R(s) C(s) R(s) C(s)

G G

1/G
X

C(s)=GR(s)
C(s)=GR(s) and
and X=C(s).{1/G}
X=R(s) =GR(s).{1/G}
6/30/2016 Amit Nevase = R(s) 116
Block Diagram Reduction Techniques

 While solving block diagram for getting single block

equivalent, the said rules need to be applied. After

each simplification a decision needs to be taken. For

each decision we suggest preferences as

6/30/2016 Amit Nevase 117

Block Diagram Reduction Techniques

First Choice

First Preference: Rule 1 (For series)

Second Preference: Rule 2 (For parallel)

Third Preference: Rule 3 (For FB loop)

6/30/2016 Amit Nevase 118

Block Diagram Reduction Techniques

Second Choice
(Equal Preference)

Rule 4 Adjusting summing order

Rule 5/6 Shifting summing point before/after block

Rule7/8 Shifting take off point before/after block

6/30/2016 Amit Nevase 119

 Example 1

G4

+
R(s) + + G1 G2 G3 + C(s)
G6

- - +

H1 G5

H2

6/30/2016 Amit Nevase 120

Rule 1 cannot be used as there are no
immediate series blocks.

Hence Rule 2 can be applied to G4, G3, G5 in

parallel to get an equivalent of G3+G4+G5

6/30/2016 Amit Nevase 121

 Example 1 cont….

Apply Rule 2
Blocks in Parallel
G4

+
R(s) + + G1 G2 G3 + C(s)
G6

- - +

H1 G5

H2

6/30/2016 Amit Nevase 122

 Example 1 cont….

Apply Rule 1 Blocks in series

R(s) + + G1 G2 C(s)
G3+G4+G5 G6

- -

H1

H2

6/30/2016 Amit Nevase 123

 Example 1 cont….

Apply Rule 3 Elimination of feedback loop

R(s) + + G1 C(s)
G2(G3+G4+G5) G6

- -

H1

H2

6/30/2016 Amit Nevase 124

 Example 1 cont….

Apply Rule 1 Blocks in series

R(s) + G1 C(s)
G2(G3+G4+G5) G6

-
1  G1H1

H2

6/30/2016 Amit Nevase 125

 Example 1 cont….

Apply Rule 3 Elimination of feedback loop

R(s) + G1G 2(G 3  G 4  G 5) G6

C(s)

- 1  G1H1

H2

6/30/2016 Amit Nevase 126

Example 1 cont….

Apply Rule 1 Blocks in series

R(s)
G1G 2(G 3  G 4  G 5) G6
C(s)

1  G1H 1  G1G 2 H 2(G 3  G 4  G 5)

6/30/2016 Amit Nevase 127

Example 1 cont….

R(s) G1G 2G 6(G 3  G 4  G 5) C(s)

1  G1H 1  G1G 2 H 2(G 3  G 4  G 5)

6/30/2016 Amit Nevase 128

Example 1 cont….

C (s) G1G 2G 6(G 3  G 4  G 5)


R ( s ) 1  G1H 1  G1G 2 H 2(G 3  G 4  G 5)

6/30/2016 Amit Nevase 129

Example 2

G4

+
R(s) + + G1 G2 G3 + C(s)

+ -

H1

H2

6/30/2016 Amit Nevase 130

Example 2 cont….

G4
Apply Rule 1
Blocks in series

+
R(s) + + G1 G2 G3 + C(s)

+ -

H1

H2

6/30/2016 Amit Nevase 131

Example 2 cont….

G4
Apply Rule 2
Blocks in parallel

+
R(s) + + G1G2 G3 + C(s)

+ -

H1

H2

6/30/2016 Amit Nevase 132

Example 2 cont….

Apply Rule 3
Elimination of feedback loop

R(s) + + G1G2 G3+G4 C(s)

+ -

H1

H2

6/30/2016 Amit Nevase 133

Example 2 cont….

Apply Rule 2 Blocks in series

R(s) + G1G 2 G3+G4 C(s)

+ 1  G1G 2 H 1

H2

6/30/2016 Amit Nevase 134

Example 2 cont….

Apply Rule 3 Elimination of feedback loop

R(s) + G1G 2(G 3  G 4) C(s)

+ 1  G1G 2 H 1

H2

6/30/2016 Amit Nevase 135

 Example 2 cont….

R(s) C(s)
G1G 2(G 3  G 4)
1  G1G 2 H1  G1G 2G3H 2  G1G 2G 4 H 2

6/30/2016 Amit Nevase 136

Example 2 cont….

C (s) G1G 2(G 3  G 4)


R( s) 1  G1G 2 H 1  G1G 2G3H 2  G1G 2G 4 H 2

6/30/2016 Amit Nevase 137

Example 3

G5

+
R(s) + G1 + G2 G3 + G4 C(s)

- -

H1

H2

6/30/2016 Amit Nevase 138

Example 3 cont….
Apply Rule 3 Elimination of feedback loop
G5

+
R(s) + G1 + G2 G3 + G4 C(s)

- -

H1

H2

6/30/2016 Amit Nevase 139

Example 3 cont….
Apply Rule 1 Blocks in series
G5

+
R(s) + G1 G2 G3 + G4 C(s)
1  G 2H1
-

H2

6/30/2016 Amit Nevase 140

Example 3 cont….
Apply Rule 2 Blocks in parallel

G5

+
R(s) + G1G 2G 3 + G4 C(s)
1  G 2H1
-

H2

6/30/2016 Amit Nevase 141

Example 3 cont….

Apply Rule 1 Blocks in series

R(s) + G1G 2G3 C(s)

G5  G4
1  G 2H1
-

H2

6/30/2016 Amit Nevase 142

Example 3 cont….
Apply Rule 3 Elimination of feedback loop

R(s) + G1G 2G3 C(s)

G 4(G5  )
- 1  G 2 H1

H2

6/30/2016 Amit Nevase 143

Example 3 cont….

R(s) G 4G5  G 2G 4G5H1  G1G 2G3G 4 C(s)

1  G 2H1  G 4G5H 2  G 2G 4G5H1H 2  G1G 2G3G 4H 2

6/30/2016 Amit Nevase 144

Example 3 cont….

C ( s) G 4G5  G 2G 4G5H1  G1G 2G3G 4


R( s) 1  G 2 H1  G 4G5H 2  G 2G 4G5H1H 2  G1G 2G3G 4 H 2

6/30/2016 Amit Nevase 145

Example 4

R(s) + + - G1 + G2 C(s)

- -

H1 H2

6/30/2016 Amit Nevase 146

Example 4 cont….
Apply Rule 3 Elimination of feedback loop

-
R(s) + + G1 + G2 C(s)

- -

H1 H2

6/30/2016 Amit Nevase 147

Example 4 cont….

R(s) + + - G1 G2 C(s)
1  G 2H 2
-

H1

6/30/2016 Amit Nevase 148

 Now Rule 1, 2 or 3 cannot be used
directly.
There are possible ways of going ahead.
a. Use Rule 4 & interchange order of summing
so that Rule 3 can be used on G.H1 loop.
G2
b. Shift take off point after 1  G 2H 2 block reduce
by Rule 1, followed by Rule 3.

Which option we have to use????

6/30/2016 Amit Nevase 149

Example 4 cont….
Apply Rule 4 Exchange summing order

1 2
R(s) + + - G1 G2 C(s)
1  G 2H 2
-

H1

6/30/2016 Amit Nevase 150

Example 4 cont….
Apply Rule 3 Elimination feedback loop

2 - 1
R(s) + + G1 G2 C(s)
1  G 2H 2
-

H1

6/30/2016 Amit Nevase 151

Example 4 cont….
Apply Rule 1 Bocks in series

2 -
R(s) + G1 G2 C(s)
1  G1H1 1  G 2H 2

6/30/2016 Amit Nevase 152

Example 4 cont….

2 -
R(s) + G1G 2 C(s)
1  G1H1  G 2 H 2  G1G 2 H1H 2

Now which Rule will be applied

-------It is blocks in parallel OR
-------It is feed back loop

6/30/2016 Amit Nevase 153

 Example 4 cont….
Let us rearrange the block diagram to understand
Apply Rule 3 Elimination of feed back loop

2
R(s) + G1G 2 C(s)
1  G1H1  G 2 H 2  G1G 2 H1H 2
-

6/30/2016 Amit Nevase 154

Example 4 cont….

R(s) G1G 2 C(s)

1  G1H1  G 2 H 2  G1G 2 H1H 2  G1G 2

6/30/2016 Amit Nevase 155

Example 4 cont….

C (s) G1G 2

R( s) 1  G1H1  G 2 H 2  G1G 2 H1H 2  G1G 2

6/30/2016 Amit Nevase 156

 Note 1: According to Rule 4
 By corollary, one can split a summing point to
two summing point and sum in any order

B
B
+
R(s) + C(s) + +
G
R(s) + G C(s)
- -

H
H

6/30/2016 Amit Nevase 157

Example 5
Simplify, by splitting second
summing point as
H1
said in note 1

-
R(s) + + G1 G2 G3 C(s)

- -

H2

H3

6/30/2016 Amit Nevase 158

 Example 5 cont….
Apply rule 3
H1 Elimination of feedback loop

+ + + - G1 G2 G3 C(s)
R(s)
- -

H2

H3

6/30/2016 Amit Nevase 159

 Example 5 cont….

Apply rule 1 Blocks in series

+ + G1 G2 G3 C(s)
R(s)
- 1  G1H 1
-

H2

H3

6/30/2016 Amit Nevase 160

 Example 5 cont….
Apply rule 3 Elimination of feedback loop

+ + G1G 2 G3
1  G1H 1 C(s)
R(s) - -

H2

H3

6/30/2016 Amit Nevase 161

 Example 5 cont….

Apply rule 1 Blocks in series

+ G1G 2 G3
1  G1H 1  G1G 2 H 2 C(s)
R(s) -

H3

6/30/2016 Amit Nevase 162

 Example 5 cont….
Apply rule 3 Elimination of feedback loop

+ G1G 2G3
R(s) 1  G1H 1  G1G 2 H 2 C(s)
-

H3

6/30/2016 Amit Nevase 163

Example 5 cont….

R(s) G1G 2G3 C(s)

1  G1H1  G1G 2 H 2  G1G 2G3H 3

6/30/2016 Amit Nevase 164

Example 5 cont….

C ( s) G1G 2G3

R( s) 1  G1H 1  G1G 2 H 2  G1G 2G3H 3

6/30/2016 Amit Nevase 165

Example 6
Apply rule 8
Shift take off point beyond block
G5
G3

+
R(s) + G1 + G2 G3 G4 + C(s)

- -

H1

H2

6/30/2016 Amit Nevase 166

Example 6 cont….
Apply rule 1
Blocks in series
1/ G5
G3

+
R(s) + G1 + G2 G3 G4 + C(s)

- -

H1

H2

6/30/2016 Amit Nevase 167

Example 6 cont….
Apply rule 2
Blocks in parallel
G5/
G3

+
R(s) + G1 + G2G3 G4 + C(s)

- -

H1

H2

6/30/2016 Amit Nevase 168

Example 6 cont….
Apply rule 3
Feedback loop

G4+(G5/
R(s) + G1 + G2G3 G3) C(s)

- -

H1

H2

6/30/2016 Amit Nevase 169

Example 6 cont….
Apply rule 1
Blocks in series

G4+(G5/
R(s) + G1 G 2G3 G3) C(s)
1  G 2G3H1
-

H2

6/30/2016 Amit Nevase 170

Example 6 cont….

R(s) + G 2G3 G5 C(s)

(G1)( )(G 4  )
1  G 2G3H1 G3
-

H2

6/30/2016 Amit Nevase 171

Example 6 cont….

G 2G3 G5
 (G1)( )(G 4  )
1  G 2G3H1 G3

G 2G3 G 4G3  G5
 (G1)( )( )
1  G 2G3H1 G3

G1G 2(G 4 G 3  G 5)

1  G 2G3H 1
6/30/2016 Amit Nevase 172
Example 6 cont….

Apply rule 3 Feedback loop

R(s) + G1G 2(G 4G 3  G 5) C(s)

- 1  G 2G3H1

H2

6/30/2016 Amit Nevase 173

Example 6 cont….

C(s)
R(s) G1G 2(G 4 G 3  G 5)
1  G 2G3H 1  G1G 2 H 2(G 3G 4  G 5)

6/30/2016 Amit Nevase 174

Example 6 cont….

C (S) G1G 2(G 4 G 3  G 5)


R(S) 1  G 2G3H 1  G1G 2 H 2(G 3G 4  G 5)

6/30/2016 Amit Nevase 175

Example 7
Apply rule 8 Shift take off point after block G4

H2

-
R(s) + G1 + G2 + G3 G4

- - C(s)

H3

H1

6/30/2016 Amit Nevase 176

Example 7 cont….
Apply rule 1 Blocks in series

H2 1/G4

-
R(s) + G1 + G2 + G3 G4

- - C(s)

H3

H1

6/30/2016 Amit Nevase 177

Example 7 cont….

Apply rule 3 Feedback loop

H2/
G4

-
R(s) + G1 + G2 + G3G4

- - C(s)

H3

H1

6/30/2016 Amit Nevase 178

Example 7 cont….

Apply rule 1 Blocks in series

H2/
G4

-
R(s) + G1 + G2 G3G 4
1  G3G 4 H 3
- C(s)

H1

6/30/2016 Amit Nevase 179

Example 7 cont….
Apply rule 3 Feedback loop

H2/
G4
-
R(s) + G1 + G 2G 3G 4
1  G 3G 4 H 3
- C(s)

H1

6/30/2016 Amit Nevase 180

Example 7 cont….

Apply rule 1 Blocks in series

R(s) + G 2G3G 4 C(s)

G1
1  G3G 4 H 3  G 2G3H 2
-

H1

6/30/2016 Amit Nevase 181

Example 7 cont….
Apply rule 3 Feedback loop

R(s) + G1G 2G3G 4 C(s)

1  G3G 4 H 3  G 2G3H 2
-

H1

6/30/2016 Amit Nevase 182

Example 7 cont….

R(s) G1G 2G3G 4 C(s)

1  G3G 4 H 3  G 2G3H 2  G1G 2G3G 4 H 1

6/30/2016 Amit Nevase 183

Example 7 cont….

C (S) G1G 2G3G 4


R(S) 1  G3G 4 H 3  G 2G3H 2  G1G 2G3G 4 H 1

6/30/2016 Amit Nevase 184

Example 8
Simplify, by splitting 3rd summing point as given in Note 1
G3

3
1 2 +
R(s) + + G1 G2 + G4 C(s)

- - -

H2 H1

6/30/2016 Amit Nevase 185

Example 8 cont….
Apply Rule 3 Elimination of Feedback loop
G3

+ +
R(s) + + G1 G2 + G4 C(s)

- - -

H2 H1

6/30/2016 Amit Nevase 186

Example 8 cont….
Apply Rule 8 Shift take off point after block
G3

+
R(s) + + G1 G2 + G4 C(s)
1  G 4H1
- -

H2

6/30/2016 Amit Nevase 187

Example 8 cont….
Apply Rule 1
Blocks in series
G3/
G2

+
R(s) + + G1 G2 + G4 C(s)
1  G 4H1
- -

H2

6/30/2016 Amit Nevase 188

Example 8 cont….
Now which rule we have to use?

G3/
G2

+
R(s) + + G1G2 + G4 C(s)
1  G 4H1
- -

H2

6/30/2016 Amit Nevase 189

Example 8 cont….
Apply Rule 2
Blocks in parallel
G3/
G2

+
R(s) + + G1G2 1 + G4 C(s)
1  G 4H1
- -

H2

6/30/2016 Amit Nevase 190

Example 8 cont….
Apply Rule 1 Blocks in series

R(s) + + G1G2 G3 G4 C(s)

1
G2 1  G 4H1
- -

H2

6/30/2016 Amit Nevase 191

Example 8 cont….

Apply Rule 3 Elimination of Feedback Loop

R(s) + + G1G2 (G 3  G 2)G 4 C(s)

G 2(1  G 4 H 1)
- -

H2

6/30/2016 Amit Nevase 192

Example 8 cont….
Apply Rule 1 Blocks in series

R(s) + G1G 2 (G 3  G 2)G 4 C(s)

1  G1G 2 H 2 G 2(1  G 4 H 1)
-

6/30/2016 Amit Nevase 193

Example 8 cont….
Apply Rule 3 Elimination of Feedback loop

R(s) + G1G 4(G 3  G 2) C(s)

(1  G1G 2 H 2)(1  G 4 H 1)
-

6/30/2016 Amit Nevase 194

Example 8 cont….

R(s) G1G 4(G 3  G 2) C(s)

1  G 4H1  G1G 2 H 2  G1G 2G 4 H1H 2  G1G 4(G 2  G 3)

6/30/2016 Amit Nevase 195

Example 8 cont….

C (s) G1G 4(G 3  G 2)


R(s) 1  G 4 H1  G1G 2 H 2  G1G 2G 4 H1H 2  G1G 4(G 2  G 3)

6/30/2016 Amit Nevase 196

Example 9
Apply rule 2 Blocks in Parallel

G4

+
R(s) + G1 + G2 + G3 C(s)

- + - -

G5 H1
H2

H3

6/30/2016 Amit Nevase 197

Example 9 cont….
Apply rule 3 Elimination of Feedback Loop

R(s) + G1+G4+ + G2 + G3
G5
- - - C(s)

H1
H2

H3

6/30/2016 Amit Nevase 198

Example 9 cont….
Apply rule 1 Blocks in Series

R(s) + G1+G4+G5 G2 G3 C(s)

1  G 2H1 1  G 3H 2
-

H3

6/30/2016 Amit Nevase 199

Example 9 cont….
Apply rule 3 Elimination of Feedback loop

R(s) + G 2G3(G1  G 4  G 5) C(s)

-
(1  G 2 H 1)(1  G 3 H 2)

H3

6/30/2016 Amit Nevase 200

Example 9 cont….

R(s) G 2G3(G1  G 4  G 5) C(s)

1  G 2 H 1  G3H 2  G 2G3H 1H 2  G 2G3H 3(G1  G 4  G 5)

6/30/2016 Amit Nevase 201

Example 9 cont….

C (s) G 2G3(G1  G 4  G 5)

R(s) 1  G 2 H 1  G3H 2  G 2G3H 1H 2  G 2G3H 3(G1  G 4  G 5)

6/30/2016 Amit Nevase 202

Example 10
Apply rule 2 Blocks in Parallel

R(s) G1 + G2 G3 +
-
- - C(s)

+
H1 H3

+
6/30/2016 Amit Nevase 203
Example 10 cont….
Apply rule 3 Elimination of Feedback Loop

R(s) G1 + G2 1+G3
-
- C(s)

+
H1 H3

6/30/2016 Amit Nevase 204

Example 10 cont….
Apply rule 8 Shift take off point after block

R(s) G1 + G2 1+G3
- 1  G2
- C(s)

+
H1 H3

6/30/2016 Amit Nevase 205

Example 10 cont….
Apply rule 1 Blocks in series

R(s) G1 + G2 1+G3
- 1  G2
- C(s)

1
1  G3

+
H1 H3
+

6/30/2016 Amit Nevase 206

Example 10 cont….
Apply rule 2 Blocks in Parallel

R(s) G1 + G 2(1  G 3)
- 1  G2
- C(s)

1
1  G3
+
H1 H3

6/30/2016 Amit Nevase 207

Example 10 cont….
Apply rule 1 Blocks in Series

R(s) G1 + G 2(1  G 3)
- 1  G2
- C(s)

H1 1
H2
1  G3

6/30/2016 Amit Nevase 208

Example 10 cont….
Apply rule 3 Elimination of Feedback loop

R(s) G1 + G 2(1  G 3)
- 1  G2
- C(s)

H 1(H 2  H 2 G 3  1)
1  G3

6/30/2016 Amit Nevase 209

Example 10 cont….

Apply rule 1 Blocks in series

R(s) G1
G 2(1  G 3)
1  G 2  G 2 H 1(1  H 2  H 2 G 3)
C(s)

6/30/2016 Amit Nevase 210

Example 10 cont….

R(s) C(s)
G1G 2(1  G 3)
1  G 2  G 2 H 1(1  H 2  H 2 G 3)

6/30/2016 Amit Nevase 211

Example 10 cont….

C (s) G1G 2(1  G 3)


R(s) 1  G 2  G 2 H 1(1  H 2  H 2 G 3)

6/30/2016 Amit Nevase 212

References

 Control System Engineering

- J. J. Nagrath, M. Gopal

 Feedback Control System

- R. A. Barapate

 Modern Control
Engineering

- K. Ogata
6/30/2016 Amit Nevase 213
Online Tutorials

 http://www.electrical4u.com
/control-engineering-
historical-review-and-types-
of-control-engineering/

 http://www.academia.edu/6
729369/EC2255-
_Control_System_Notes_solv
ed_problems_
6/30/2016 Amit Nevase 214
 Thank You
Amit Nevase
6/30/2016 Amit Nevase 215