International Journal of Control and Automation

Vol. 6, No. 3, June, 2013

Implementation of Fuzzy Technique Based on LabVIEW for Control

Gas System Using USB 6009

1 3 4
Arvind Kumar Parwal , Gaurav Parwal2, Alok Sharma and Mohammad Arif Khan
1
Department of Electrical & Electronics, CEST, Fiji National University, Fiji
2
Dept of Computer Science, Amity School of Engineering & Technology, Amity
University, Jaipur, India
3
School of Engineering and Physics, University of South Pacific, Fiji
4
Electrical & Electronics Dept, Krishna Institute of Engineering & Technology,
Ghaziabad, India
1
[email protected], [email protected],
3
[email protected], [email protected]

Abstract
The quality of Natural Gas Piping Systems (NGPS) must be ensured against any
manufacturing defects. For this purpose, we develop a special testing machine (STM)
constructed at the lab to test (NGPS). The proposed (STM)[1] function is based on testing the
weak points at the pipe connections e.g. pipe bends, and intermediate connections. For more
than 1500 pieces of (NGPS), crack propagation simultaneously followed up and monitored on
the output screen at the critical positions of the pipelines connections. The control system
utilizes the LabVIEW™ tools for various signals acquisition and monitoring also for
designing the control system strategy.

Keywords: Natural Gas Piping Systems (NGPS), special testing machine (STM),
LabVIEW, hydraulic power cylinder (HPC)

1. Introduction
Piping systems are like arteries and veins for power plants, oil refineries, petroleum
pipelines, cities urbane plan watering and light gas systems and food industry. The natural gas
transportation, and distribution pipelines convey natural gas from the source and storage tank
to the utilization stations, e.g., power plants, various industrial regions. Pipe bends are
considered as the most critical components in piping systems. Furthermore, pipe bends are
usually built-in to reduce anchor reactions. Special testing machine (STM) [1] is a unique
testing machine which, used to implement all mechanical tests mainly for Natural Gas Piping
Systems (NGPS) also, for other types of flat and fracture specimens. STM can perform
several tests namely; tension, compression, bending, torsion, fatigue, and combined loading
(opening and closing mode) under internal pressure. The other unique feature is related to
testing speeds which are about three times compared with other testing machines. The
maximum testing speed and maximum span are, V = 6000 [mm/min], and S = 950 [mm]
respectively [10].

365
International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

2. System Design
STM consists of the following parts; (i) Mainframe which contains fixing accessories for
pipes, flat, and fracture specimens, (ii) Hydraulic power unit [2], (iii) Electrical power unit
[3], and (iv) Automation unit as shown in Figure1. The automation unit implements three
main tasks; the first task is to control the orientation of the hydraulic power cylinder (HPC)
[4-6] to change the mode of testing. For tension or compression mode the acting force must
be perpendicular to the specimen surface so that HPC should be oriented vertically as shown
in Figure 2.

Figure 1. Photo of Testing Machine for Natural Gas Piping Systems (NGPS)

The torsion test needs to rotate HPC around the X-axis (90o) to produce the torsion force
(FZ). In case of fatigue test, HPC is oriented to the required loading point after that the
fluctuated force acts on the specimen for several cycles. Orientation control involves three
electric motors for vertical motion along Y-axis, for horizontal motion along X-axis, and for
rotation around X-axis as shown in Figure 2.
The Second task is to control the hydraulic system. The hydraulic system consists of i)
Hydraulic service unit including pump, filter and hydraulic safety elements. ii) Hydraulic
power cylinder (HPC) which the testing force will be generate on the pipe.

366
 International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

Figure 2. Three Dimensions Model for Special Testing Machine (STM)

iii) Proportional hydraulic valve with embedded power amplifier to control the direction and
the speed of the HPC. Integration of different sensors types with up normal environmental
conditions requires robust data acquisition card. The DAQ is connected to the hydraulic valve
power amplifier through an analog channel. The hydraulic valve receives a signal with ± 10
volt to control the speed of HCP in both directions (positive and negative Y-axis direction).

2.1. Fuzzy Toolkit

The fuzzy toolkit is well suited for control applications on nonlinear or complex dynamics
systems such as hydraulic positioning systems.
The dynamic behavior of the hydraulic valve is highly nonlinear along the wide range of
speeds therefore; the fuzzy controller is utilized to control the hydraulic valve. Fuzzy
controllers generally have many advantages over other controller’s types. For example, it
does not require a complex mathematical model; also it behaves a good robustness against the
system disturbances from the hydraulic elements. National Instrument [7, 8] provides an
excellent tool to build the fuzzy controllers. The STM automation is based on the fuzzy
controller block witch included in the LabVIEW fuzzy logic toolkit. A fuzzy membership
function editor allows to quantitatively defining linguistic terms for input variables with
simple GUI interface. First the fuzzification process is entered by selecting the type of
membership function for inputs. The inputs are the position error and rate of the position
error. The output is the control voltage signal to control the hydraulic valve. Then a rule-base
editor is used to define the rules of the controller output based on the linguistic input terms.
The fuzzy logic toolkit is used to implement a rule-based feedback controller. Figure 3 shows
the block diagram for control loop and signal monitoring loop.

367
International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

2.2. Block Diagram

The fuzzy logic toolkit is used to implement a rule-based feedback controller. Figure 3
shows the block diagram for control loop and signal monitoring loop.

Figure 3. Block Diagram for Control Loop and Signal Monitoring Loop

The third task is to monitor the test signals; during the test many signals from sensors are
acquired and monitored as shown in Figure 4 and Figure 5. STM sensors are Precise linear
potentiometer (measuring range 600 mm with 0.01 mm resolution) to position the HPC
during the test, the potentiometer signal used to control the position of HPC.
Two linear Variable Differential Transformer (LVDT) sensor (Measuring range 100 mm
with 0.001 mm resolution) to measure the deflections of the straight pipe specimen at two
different loading points. High accuracy load cell with capacity up to one ton (up to 150 %
over nominal load) to monitor the applied force (N) from HPC on the pipe bend.
A novel sensor called “Clip Gauge” is designed especially for the machine to measure the
crack opening displacement (COD) during the tests with 0.001mm accuracy. Clip gauge
sensor is used only for fracture specimens, so that we customize a separate data acquisition
card (NI USB 6008) to monitor this special sensor.

3. LabVIEW
LABVIEW (Laboratory Virtual Instrumentation Engineering Workbench) is a
development environment [5] that utilizes a graphical programming language, called “G”,
developed by National Instruments. It is mainly used for data acquisition, instrument control
and industrial automation. The LABVIEW program contains tools for acquiring, analyzing,
storing and displaying data. Programs created in LABVIEW are called virtual instruments
(VIs). VIs are made up of block diagrams and front panels. Block diagrams are where the
code is developed and contain all the sub VIs (or subroutines) within the program. The front
panel acts like a user interface where the user can input and extract data from the VI.

368
 International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

3.1. NI USB 6009

The NI‐USB [7] shown in Figure 4, is a module used for data acquisition which can be
connected to PC via a USB. It has 8 analog inputs, two analog outputs and 12 digital I/O
connections. The module is compatible with programming software LABVIEW. All sensors
signals are a real time monitored and plotted such as a special plot for force-deflection curve
to characterize the behavior of pipe bend (Elbow) during the test. The natural gas pipes are
tested on the STM for characterization and simulation.

Figure 4. National Instruments USB 6009

Characterization involves implementing the standard tests with general loading conditions
to the pipes after the manufacturing processes. On the other hand simulation involves
implementing special tests with loading conditions that depends to where and how the pipe
will be loaded.
On the other hand simulation involves implementing special tests with loading conditions
that depends to where and how the pipe will be loaded.

3.1.1. Front Panel

Figure 5 shows the Front Panel of the control system.

369
International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

Figure 5. Front Panel for the Control System

3.1.2. Block Diagram

The block diagram Figure 6 (block diagram for the control system) shows the simulation in
LabVIEW, a product of National Instruments.
The block diagram has programmed in loop that is include with a status control known as
true and false. Here in this program we use continue if false status.
Vis has been selected from the VI palette for realization of data.

Figure 6. Block Diagram for the Control System

370
 International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

4. Results
Above System improves the mechanical testing capabilities and production quality of
Natural Gas Piping Systems (NGPS). Current testing rates are insufficient to ensure safety
conditions especially for (NGPS). Also, the automation systems for current testing machines
are indirectly customized for piping system inspection.

Front Panel for the Control System

Block Diagram for the Control System

371
International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

5. Conclusions
A novel design of a special testing machine (STM) introduces testing rates three times
compared with other testing machines. All tests are implemented in one machine with
multifunction monitoring and flexible automation system. The quality of Natural Gas Piping
Systems (NGPS) is ensured against any manufacturing defects. For this purpose, we tried to
develop a special testing machine (STM) constructed at the lab to test (NGPS). The proposed
(STM) function is based on testing the weak points at the pipe connections e.g. pipe bends,
and intermediate connections.

Acknowledgements
I, Arvind Parwal, would like to thank Authors for their valuable time. I would like to thank
Mr. Gaurav Parwal for his valuable time throughout the work and for providing a lean
guidance on National Instruments [8] products. I thank Dr. Alok Sharma & Dr Mohammad
Arif Khan for being dedicated Authors. I would like to thanks concerned Departments &
laboratory for providing us better & back end software solutions.

References
[1] Automated Test Equipment (ATE) Fixtures – Glue and Black Magic, Canadian Conference on Electrical and
Computer Engineering, (2006).
[2] System Control of Power Electronics Interfaced Distribution Generation Units, Power Electronics and Motion
Control Conference, IPEMC 2006, CES/IEEE 5th International, vol. 1, (2006).
[3] K. Amundson, J. Raade, N. Harding and H. Kazerooni, “Hybrid hydraulic-electric power unit for field and
service robots”, Intelligent Robots and Systems, (IROS 2005), 2005 IEEE/RSJ International Conference,
(2005).
[4] D. A. Gilmour, J. P. Hanna and G. Blank, “Dynamic resource allocation in an HPC environment”, Computer
Architecture, Proceedings, 31st Annual International Symposium, (2004).
[5] N. Naksinehaboon, N. Taerat, C. Leangsuksun, C. F. Chandler and S. L. Scott, “Benefits of Software
Rejuvenation on HPC Systems”, Parallel and Distributed Processing with Applications (ISPA), 2010
International Symposium.
[6] Design and implementation of fuzzy based controller for modern elevator group, Industrial Electronics and
Applications (ISIEA), 2011 IEEE Symposium.
[7] NI‐USB 6009 http://sine.ni.com/nips/cds/view/p/lang/en/nid/14604.
[8] National Instruments, LabVIEW User Manual, Texas: National Instruments, (2003).
[9] A. Abdelkrim, C. Ghorbel and M. Benrejeb, “LMI-based tracking control for Takagi-Sugeno fuzzy model”,
International Journal of Control and Automation, vol. 3, no. 1, (2010) March.
[10] D. H. Shin, S. T. Kwon, S. H. Park and M. G. Joo, “Fuzzy State Feedback Control for Way-Point Tracking of
Autonomous Underwater Vehicle”, International Journal of Control and Automation, vol. 6, no. 1, (2013)
February.
[11] C. Dhaya, and G. Zayaraz, “Fuzzy based Quantitative Evaluation of Architectures using Architectural
Knowledge”, International Journal of Advanced Science and Technology, vol. 49, (2012) December.

372
 International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

Authors

Arvind K Parwal, presently working as Lecturer I with Dept of

Electrical & Electronics in CEST, Fiji National University. He received
his Bachelor of Technology in Electronics & Instrumentation in 2005,
and received his Masters of Engineering in 2007 from Thapar
University, Patiala, India. His area of interest is Virtual
Instrumentation; LabVIEW based Modeling, Fuzzy & Neural
Networks, Renewable Energy, Control & Automation, and Signal
Processing.

Gaurav Parwal, received his Bachelor of Technology in 2011 from

Faculty of Engineering, Punjabi University Patiala, India. Currently he
is pursuing his Masters of Technology from ASET, Amity School of
Technology, Jaipur, India. His area of Interest is Graphics, Signal &
Image Processing & Artificial Intelligence, MATLAB Simulation &
Neuro & Fuzzy MATLAB tool kits are his Major area of Interest.

Dr. Alok Sharma is currently working as Senior Lecturer in

Electronics Engineering with University of South Pacific, Fiji. He is
having vast teaching & research experience. "Alok Sharma received
the BTech degree from the University of the South Pacific (USP),
Suva, Fiji, in 2000 and the MEng degree, with an academic excellence
award, and the PhD degree in the area of pattern recognition from
Griffith University, Brisbane, Australia, in 2001 and 2006,
respectively. He was with the University of Tokyo (2010-2012) as a
research fellow. He is also with the Signal Processing Laboratory,
Griffith University, and the University of the South Pacific. He
participated in various projects carried out in conjunction with
Motorola (Sydney), Auslog Pty., Ltd. (Brisbane), CRC Micro
Technology (Brisbane), the French Embassy (Suva) and JSPS (Japan).
His research interests include pattern recognition, computer security,
human cancer classification and protein fold recognition. He reviewed
several articles and is in the editorial board of several journals. He is a
member of IEEE."

Dr. Mohammad Arif Khan, presently working as Assistant

Professor with Electrical & Electronics Dept, Krishna Institute of
Engineering & Technology, Ghaziabad, India. He received his PhD,
MEng and BEng. degree from Aligarh Muslim University, Aligarh,
India. His areas of Interest are Power system & Drives, Signal
Conditioning, Dr Arif has published his book “Comparative analysis of
pulse width modulation schemes for five-phase voltage source
inverter”, ISBN 978-3-659-27121-2, Lambert Academic Publishing
(LAP), Germany, November 2012. He is Member of the editorial

373
International Journal of Control and Automation
Vol. 6, No. 3, June, 2013

committee of International Journal of Electronics Communications and

Electrical Engineering (IJECEE).
(https://sites.google.com/site/ijeceejournal/editorial) and Member of
the review committee for international Journal of Power Electronics &
Drives systems (IJPEDS). He has provided project guidance at Maters
and Bachelors level of Engineering.

374