Datasheet

Ilitek
ILI2511

The information contained in this document has been carefully researched and is, to the best
of our knowledge, accurate. However, we assume no liability for any product failures or
damages, immediate or consequential, resulting from the use of the information provided
herein. Our products are not intended for use in systems in which failures of product could
result in personal injury. All trademarks mentioned herein are property of their respective
owners. All specifications are subject to change without notice.
 ILI2511

ILI2511
Single Chip Capacitive Touch Sensor
Controller

Preliminary
Specification

Version: V1.05
Date: 2016/11/28

ILI TECHNOLOGY CORP.

8F., No.1, Taiyuan 2nd St., Zhubei City, Hsinchu County 302, Taiwan (R.O.C.)
Tel.886-3-5600099; Fax.886-3-5600055
http://www.ilitek.com
 Capacitive Touch Sensor Controller
ILI2511

Revision History
Version Date Page Description
V1.01 2016/8/10 All Preliminary released

V1.02 2016/9/19 6,7,17,18 Modify the pin description & application circuit.

V1.03 2016/10/27 6,7 Modify the pin assignment & pin description.

V1.04 2016/11/3 2 Modify the page information of revision history.

V1.05 2016/11/28 4,17,18 Modify the feature and application circuit.

Page 2 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

Table of Content
REVISION HISTORY ......................................................................................................................................... 2

TABLE OF CONTENT ....................................................................................................................................... 3

1. DESCRIPTION ........................................................................................................................................... 4

2. FEATURES ................................................................................................................................................ 4

3. BLOCK DIAGRAM..................................................................................................................................... 5

4. PIN DEFINITION ........................................................................................................................................ 6

4.1 QFN-88 PIN ASSIGNMENT ......................................................................................................................................... 6

4.2 QFN-88 PIN DESCRIPTION ......................................................................................................................................... 7

5. ELECTRICAL CHARACTERISTICS ......................................................................................................... 9

5.1 ABSOLUTE MAXIMUM RATINGS ................................................................................................................................. 9

5.2 RECOMMENDED OPERATING CONDITIONS ............................................................................................................... 10
5.3 DC CHARACTERISTICS............................................................................................................................................. 11
5.4 I2C AC CHARACTERISTICS ...................................................................................................................................... 13

6. POWER SEQUENCE ............................................................................................................................... 14

6.1 POWER-ON SEQUENCE ............................................................................................................................................. 14

6.2 POWER-OFF TO POWER-ON SEQUENCE..................................................................................................................... 15

7. PACKAGE INFORMATION...................................................................................................................... 16

7.1 QFN-88 PACKAGE DIMENSION ................................................................................................................................ 16

8. TYPICAL APPLICATION CIRCUIT ......................................................................................................... 17

8.1 USB APPLICATION CIRCUIT ..................................................................................................................................... 17

8.2 I2C APPLICATION CIRCUIT ....................................................................................................................................... 18

Page 3 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

1. Description
The ILI2511 is a single chip capacitive touch sensor controller optimized for POS,
ATM and Industry Capacitive Touch Panel applications. It integrates high speed
Capacitance to Digital Converter (CDC), total 65 channels including high voltage
Driving and Sensing channels, high voltage Charge Pump Controller, high voltage
regulator and 32-bit high performance Micro-controller (MCU). In order to minimize
system design cost, ILI2511 also integrates a USB 5V to 3.3V Low Drop-out
Regulator and supports 1.8V/3.3V input power supply operation for I2C, SPI, UART,
GPIO. With compact QFN-88 package, its package size is 10mm*10mm*1mm and
pad pitch is 0.4mm. ILI2511 meets all Windows 8.1 and Windows 10 requirements
with best user touch experience and highest noise immunity performance.

2. Features

65 channels for capacitive touch panel

Flexible driving or sensing channel assignment

Max TX channel number is 42

Max RX channel number is 41

Programmable driving voltage for driving channels

High voltage charge pump controller with programmable high voltage regulator

High speed ADC converter

Support baseline calibration function

Support mutual-capacitance sensing

Support self-capacitance sensing

Integrated USB5V to 3.3V Low Drop-out Regulator

Support 1.8V and 3.3V Operation of VDDIO for I2C, SPI, UART, GPIO

Built-in noise processing function

Support IEC 61000-4-6 (CS test), Level 3: 10Vrms

Built-in 32-bit high performance Micro-controller (MCU)

Input voltage low level detection circuit

Input voltage power on reset circuit

Driving to Sensing mutual capacitance: 1pF to 4pF

Page 4 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

3. Block Diagram

LDO
HV Charge Pump
LVD

USB OSC
SPI XTAL Timer
I2C PLL 65-ch HV I/O
CDC
Memory
32-bit
CPU core Flash
SRAM
ROM

Figure 3-1: ILI2511 Block Diagram

Page 5 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

4. Pin Definition
4.1 QFN-88 Pin Assignment

Bottom View

UART_TX
VDDIO
TX[13]

TX[12]

TX[11]

TX[10]

RSTN
TX[9]

TX[8]
TX[7]

TX[6]

TX[5]

TX[4]

TX[3]

TX[2]

TX[1]

VGH

GND
VTX
SDA
SCK
INT
67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88
TX[14] 66 1 C2N

TX[15] 65 2 C2P
TX[16] 64 3 C1N

TX[17] 63 4 C1P

TX[18] 62 5 C0N

TX[19] 61 6 C0P

TX[20] 60 7 VDD3D

TX[21] 59 8 DM

TX[22] 58 9 DP

TX[23] 57 10 VDD5V
TX[24] 56 11 VDD16

RX[41] 55 12 XTAL_IO1

RX[40] 54 13 XTAL_IO2
RX[39] 53 14 VDD3A

RX[38] 52 15 RX[1]

RX[37] 51 16 RX[2]
RX[36] 50 17 RX[3]

RX[35] 49 18 RX[4]
RX[34] 48 19 RX[5]
RX[33] 47 20 RX[6]

RX[32] 46 21 RX[7]
RX[31] 45 22 RX[8]
44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23
RX[30]

RX[29]

RX[28]

RX[27]

RX[26]

RX[25]

RX[24]

RX[23]
RX[22]

RX[21]

RX[20]

RX[19]

RX[18]

RX[17]

RX[16]

RX[15]

RX[14]
RX[13]

RX[12]

RX[11]

RX[10]

RX[9]

Figure 4-1: ILI2511 QFN-88 Pin Assignment

Page 6 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

4.2 QFN-88 Pin Description

Table 4-1 Pin Type Define

Symbol Description
P Power pad
CLK Clock
I Input only
O Output only (Push-pull)
I/O input / output pad

Table 4-2 ILI2511 Pin Description

Name Type Description

5V or 3.3V input power supply, connect 1uF capacitor to system

VDD5V P
ground

3.3V regulator output or 3.3V input power supply, connect 1uF

VDD3D P
capacitor to system ground

3.3V regulator output or 3.3V input power supply, connect 1uF

VDD3A P
capacitor to system ground

1.8V/3.3V input power supply for I2C, SPI, UART, GPIO, connect 1uF
VDDIO P
capacitor to system ground

VDD16 P 1.6V regulator output, connect 1uF capacitor to system ground

VTX P HV regulator output, connect 1uF capacitor to system ground

VGH P Charge pump HV output, connect 1uF capacitor to system ground

GND P connect to system ground

C2N P Cathode of charge pump capacitor, connect 1uF capacitor to C2P

C2P P Anode of charge pump capacitor, connect 1uF capacitor to C2N

C1N P Cathode of charge pump capacitor, connect 1uF capacitor to C1P

C1P P Anode of charge pump capacitor, connect 1uF capacitor to C1N

C0N P Cathode of charge pump capacitor, connect 1uF capacitor to C0P

C0P P Anode of charge pump capacitor, connect 1uF capacitor to C1N

DM I/O USB interface

DP I/O USB interface

XTAL_IO1 I/O External crystal input, connect 12Mhz crystal for USB application

XTAL_IO2 I/O External crystal output, connect 12Mhz crystal for USB application

RSTN I/O External hardware reset input

Page 7 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

INT I/O Interrupt output

UART_TX I/O UART TXD output

I2C_SCL I/O I2C interface, clock input

I2C_SDA I/O I2C interface, data input

RX[1:23] I/O Typical touch panel sensing channels

Typical touch panel sensing channels can be configured to driving

RX[24:41] I/O
channels

TX[1:24] I/O Typical touch panel driving channels

Page 8 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

5. Electrical Characteristics
5.1 Absolute Maximum Ratings

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. These are for stress ratings. Functional operation of the device at these or any other conditions
beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute
maximum rating conditions for extended periods may remain possibility to affect device reliability.

Table 5-1: Absolute Maximum Ratings

Parameter Symbol Min Max Unit
USB 5V input power supply voltage VDD5V -0.3 6.0 V

VDD3A to GND VDD3A -0.3 3.6 V

VDD3D to GND VDD3D -0.3 3.6 V

VDDIO to GND VDDIO -0.3 3.6 V

VDD16 to GND VDD16 -0.3 1.65 V

VGH to GND VGH -0.3 32 V

VTX to GND VTX -0.3 32 V

ESD Susceptibility HBM (Human Body Mode)(Note 1) HBM 4000 V

ESD Susceptibility MM (Machine Mode) MM 400 V

Note 1: Devices are ESD sensitive. Handling precaution is recommended.

Page 9 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

5.2 Recommended Operating Conditions

Table 5-2: Recommended Operating Conditions

Parameter Symbol Min Max Unit
USB 5V input power supply voltage VDD5V 4.4 5.5 V

VDD3A to GND VDD3A 3.0 3.6 V

VDD3D to GND VDD3D 3.0 3.6 V

VDDIO to GND VDDIO 1.8 3.6 V

VGH to GND VGH -0.3 32 V

VTX to GND VTX -0.3 32 V

Operating Ambient Temperature Range TA -40 105 ºC

Operating Junction Temperature Range TJ -40 125 ºC

Storage Ambient Temperature Range TST -40 150 ºC

Note: The device is not guaranteed to function outside its operating conditions.

Page 10 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

5.3 DC Characteristics

Table 5-3: Input Power Supply

(VDD3A = VDD3D = 3.3V, Topr = 25ºC)
Item Symbol Min Typ. Max Unit Condition
USB 5V input power supply voltage VDD5V 4.4 5 5.5 V @ USB

Digital input power supply voltage* VDD3D 3.0 3.3 3.6 V

Analog input power supply voltage VDD3A 3.0 3.3 3.6 V

I/O input power supply voltage* VDDIO 1.8 3.6 V

*If VDDIO & VDD3D is not supplied power, there is risk of I/O pin with current leakage

Table 5-4: DC Characteristics

(VDD3A = VDD3D = 3.3V, Topr = 25ºC)
Item Symbol Min Typ. Max Unit Condition
Operation current Iop 100 mA Active Mode / 21.5”

Input Low Voltage VIL1 0 0.3VDDIO V

Input High Voltage VIH1 0.6VDDIO VDDIO+0.5 V

Hysteresis voltage VHY 0.2VDDIO V

Input Low Voltage, XT_In VIL2 0 0.6 V VDDIO=3.3V

Input High Voltage, XT_In VIH2 2.6 VDDIO+0.2 V VDDIO=3.3V

Negative going threshold,

VILS 0 0.2VDDIO V
/Reset

Positive going threshold,

VIHS 0.6VDDIO VDDIO+0.5 V
/Reset

VDDIO =3.3V,
Output High Voltage VOH 0.7VDDIO V
IOH=8mA

VDDIO =3.3V,
Output Low Voltage VOL 0.3VDDIO V
IOL=10mA

Page 11 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511
Table 5-5: USB DC Characteristics
Item Symbol Min Typ. Max Unit Condition
Input Low VIL 0.8 V

Input High (driven) VIH 2.0 V

Differential input sensitivity VDI 0.2 V (D+) – (D-)

Differential common-mode range VCM 0.8 2.5 V Includes VDI range

Single-ended receiver threshold VSE 0.8 2.0 V

Receiver hysteresis VRH 200 mV

Output low (driven) VOL 0 0.3 V

Output high (driven) VOH 2.8 3.6 V

Output signal cross voltage VCRS 1.3 2.0 V

Pull-up resistor RPU 1.425 1.575 kΩ

Pull-down resistor RPD 14.25 15.75 kΩ

Termination Voltage for upstream

VTRM 3.0 3.6 V
port pull up (RPU)

Table 5-6: Crystal Characteristics

Item Symbol Min Typ. Max Unit Condition
Input clock frequency fXIN 12 MHz External crystal

Page 12 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

5.4 I2C AC Characteristics

Table 5-7: I2C AC Characteristics

Standard-mode Fast-mode
Parameter Symbol Unit
Min Max Min Max
SCL clock frequency fSCL 0 100 0 400 kHz

Hold time START condition tHD;STA 4.0 - 0.6 - us

LOW period of the SCL clock tLow 4.7 - 1.3 - us

HIGH period of the SCL clock tHigh 4.0 - 0.6 - us

Set-up time for a repeated START

tSU:STA 4.7 - 0.6 - us
condition
Data hold time tHD;DAT 300 - 300 - ns

Data set-up time tSU;DAT 250 - 100 - ns

Rise time of both SDA and SCL

tr - 1000 20 300 ns
signals (30% to 70%)
Fall time of both SDA and SCL
tf - 300 20 300 ns
signals (70% to 30%)
Set-up time for STOP condition tSU;STO 4.0 - 0.6 - us

Bus free time between a STOP and

tBUF 4.7 - 1.3 - us
START condition
Capacitive load for each bus line Cb - 400 - 400 pF

Noise margin at the LOW level for

VnL 0.1VDD - 0.1VDD - V
each connected device
Noise margin at the HIGH level for
VnH 0.2VDD - 0.2VDD - V
each connected device

Page 13 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

6. Power Sequence
6.1 Power-on Sequence

USB Commands or
RSTN I2C Commands

VDD5V ~
0.9 * VDD5V
~

Time
T2 T3

VDDIO
0.9 * VDDIO
~

T1
Time

1. T1: the time difference between 0.9*VDD5V and 0.9*VDDIO. T1 must be ≥ 0 sec.

2. T2: the time difference between 0.9*VDDIO and RSTN. T2 must be ≥ 200 us.

3. T3: the time difference between RSTN and Commands.

T3 in case of USB must be ≥ 20 ms.

T3 in case of I2C must be ≥ 300 ms.

Page 14 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

6.2 Power-off to Power-on Sequence

VDD5V ~

0.5V
Time
Tg

Tg : the time difference between power-off and power-on. Tg must be > 10us.

Note. During the power off time, the VDD5V must be lower than 0.5V that make sure the touch controller
have been correctly reset.

Page 15 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

7. Package Information
7.1 QFN-88 Package Dimension

Top View Bottom View

Figure 7-1: Package Information of QFN-88

Page 16 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

8. Typical Application Circuit

8.1 USB Application Circuit

ILI2511
5Vdc C0P
VDD5V 1uF / 50V
1uF / 25V
X 7R
X 7R
C0N

VDD3A C1P
1uF / 25V 1uF / 50V
X7R X 7R

C1N
VDD3D
1uF / 25V C2P
X 7R 1uF / 50V
X 7R
C2N
VDD16
1uF / 25V
X 7R
VGH
1.8Vdc / 3.3Vdc 1uF / 50V
X 7R
VDDIO
1uF / 25V
X7R
VTX
1uF / 50V
10KΩ
X 7R

RSTN
1uF / 25V
X7R XTAL_IO1
12MHz

XTAL_IO2

TX[1:24]
TX[1:24]

RX[1:41]
RX[1:41]
UART to HOST
UART_TX
Controller

DM
USB to HOST
Controller DP

I2C_SCL
GND
I2C to HOST I2C_SDA
Controller
INT

Figure 8-1: ILI2511 USB Application Circuit

Page 17 of 18 Version: 1.05

 Capacitive Touch Sensor Controller
ILI2511

8.2 I2C Application Circuit

ILI2511
3.3Vdc C0P
VDD5V 1uF / 50V
1uF / 25V
X 7R
X7R
C0N

VDD3A C1P
1uF / 25V 1uF / 50V
X7R X7R
C1N
VDD3D
1uF / 25V C2P
X 7R 1uF / 50V
X7R
C2N
VDD16
1uF / 25V
X7R
VGH
1.8Vdc / 3.3Vdc 1uF / 50V
X 7R
VDDIO
1uF / 25V
X7R
VTX
10KΩ 1uF / 50V
X 7R

RSTN
1uF / 25V
X7R XTAL_IO1
12MHz

XTAL_IO2

TX[1:24]
TX[1:24]

RX[1:41]
RX[1:41]

UART to HOST UART_TX

Controller

I2C_SCL

I2C to HOST
I2C_SDA
Controller GND

INT

Figure 8-2: ILI2511 I2C Application Circuit

Page 18 of 18 Version: 1.05

Our company network supports you worldwide with offices in Germany, Great Britain, Turkey and the USA.
For more information please contact:

Distec GmbH FORTEC Elektronik AG

Augsburger Str. 2b Lechwiesenstr. 9
82110 Germering 86899 Landsberg am Lech
Germany Germany

Phone: +49 (0)89 / 89 43 63-0 Phone: +49 (0)8191 / 911 72-0

Fax: +49 (0)89 / 89 43 63-131 Fax: +49 (0)8191 / 217 70
E-Mail: [email protected] E-Mail: [email protected]
Internet: www.datadisplay-group.de Internet: www.fortecag.de

Display Technology Ltd. Apollo Display Technologies, Corp.

5 The Oaks Business Village 87 Raynor Avenue,
Revenge Road, Lordswood Unit 1Ronkonkoma,
Chatham, Kent, ME5 8LF NY 11779
United Kingdom United States of America
Phone: +44 (0)1634 / 67 27 55 Phone: +1 631 / 580-43 60
Fax: +44 (0)1634 / 67 27 54 Fax: +1 631 / 580-43 70
E-Mail: [email protected] E-Mail: [email protected]
Internet: www.datadisplay-group.com Internet: www.apollodisplays.com

Sales Partner:

DATA DISPLAY BİLİŞİM TEKNOLOJİLERİ

İÇ VE DIŞ TİCARET LİMİTED ŞİRKETİ
Barbaros Mh. Ak Zambak Sk. A Blok D:143
34376 Ataşehir / Istanbul
Turkey
Phone: +90 (0)216 / 688 04 68
Fax: +90 (0)216 / 688 04 69
E-Mail: [email protected]
Internet: www.data-display.com.tr