Installation Guide

for Andersen® LuminAire™ Retractable Insect Screen Door

with SlideAway® Insect Screen System
Designed for 32” – 36” wide by 80” tall single hinged doors with suitable mounting surface.
For installation help please visit www.AndersenLuminAire.com/install
Please Do Not Return Product to Store!
PLEASE call the Storm Door Solution Center at 844-813-6664,
with any questions regarding installation, lost part replacement, or anything else related to your retractable
insect screen purchase. Replacement parts can also be found at: parts.andersenstormdoors.com
Read this entire guide before you begin your installation. If your abilities do not
match the requirements of this installation, contact an experienced contractor.

PARTS OVERVIEW
Your installation kit should contain the following parts.

1 Screen Housing (one with handle & orange clips)

2 Latch Housing (one without handle or clips)
4 4
3 Screen Tracks (top and bottom)
4 End Caps (attached to ends of housings) 3
6
5 Sill Adapter
6 Orange Installation Clips
7 Shipping Plastic Wrap

7
8 Not Shown
Screw Pack containing:
• 1 inch #8 screws (qty 6) 1 2
• 1/2 inch #8 self-tapping screws (qty 3)
• 1/8 inch Drill Bit
• #2 Phillips Bit

NOTE: The orange installation clips attached to the Screen
Housing provide product protection during shipping and
installation. DO NOT extend screen from housing or remove
installation clips until instructed.
6
3
NOTICE
To avoid product damage, be sure to place all parts of your retractable 4 4
insect screen on a soft non-abrasive surface such as carpet, drop cloth
placed on your lawn or cardboard.

Andersen SDD, PO Box 853

Emco Enterprises, Inc., is a wholly owned subsidiary of Andersen Corporation. Emco Enterprises, Inc.
Des Moines, IA 50306-0853
manufactures and supports the limited warranties for Andersen® and EMCO® doors. “Andersen”,
Rev 06-2018v1 Print in Color
“EMCO” and all other marks where denoted are trademarks of Andersen Corporation. ©2018
Andersen Corporation. All rights reserved.
p/n 900106
1
 SAFETY FIRST: Please read and follow all Cautions and Warnings in this guide.

WARNING WARNING
Follow manufacturers' instructions for hand and power Windows and doors can be heavy. Use safe lifting techniques and a reasonable number of people with enough
tools. Always wear safety glasses. Failure to do so could strength to lift, carry, and install window and door products. Heavier windows and doors will require mechanical
result in injury, product or property damage. assistance. Failure to do so could result in injury, product or property damage.

CAUTION WARNING
Metal components of the retractable insect screen may Metal fasteners and components could corrode when exposed to preservative-treated or fire-retardent treated
become hot when exposed to sunlight. lumber. Use approved fasteners and components to fasten window or door. Failure to do so could cause a failure
resulting in injury, product or property damage.
IMPORTANT Fastener must attach to a structural framing member with a 1" minimum fastener embedment. Failure to do so
The retractable insect screen is intended for reasonable could result in injury, product or property damage.
insect control and not the retention of objects, persons,
or pets within the interior. The retractable insect screen DO NOT remove screws that attached installation clips or gusset plates to window or door frames. Doing so could
will not stop a person from falling through the door. result in injury, product or property damage.

This is the Safety Alert Symbol used to alert you to

RECOMMENDED TOOLS For installs less potential injury hazards. Obey all safety messages that
than 31-7/8" wide follow this symbol to avoid possilbe injury or death.
1/8 Drill Bit
Drill #2 Phillips Bit (provided) Signal Word and Consequence
(provided)
Sealant COULD WARNING COULD CAUTION
Hacksaw
Metal Result in: Major Injury / Death Result in: Minor Injury
File
Safety Glasses NOTICE IMPORTANT
Scissors
COULD
Result in: Product or Property Procedure and Product
Damage Information
Screwdriver Tape Measure Work Gloves

! !
MEASURE - VERIFY MOUNTING SURFACE REQUIREMENTS AND MEASURE DOOR OPENING*

! !
Verify that the exterior brickmould, trim board or casing (exterior trim) is firmly attached to the
opening structure and is a material that is suitable to sufficiently fasten the retractable insect
screen to the door opening. The performance of the retractable insect screen could be effected
over time if it is not sufficiently fastened to the opening.
To install the retractable
5/8” insect screen door, you must verify that the opening width,
1/2” W1
3/4" MIN FLAT
SURFACE ON FACE

!
height and mounting surface are suitable size to properly install into the opening.
1. Measure the width at the top (W1), middle (W2), and bottom (W3) of the opening (see Figure 1).

!
Measure from the inside of the exterior trim. Utilizing
5/8” 1/2” the narrowest width, reference1/2”
chart below.
3/4" MIN
2. Measure the height at the center of the opening, from the bottom of the exterior trim at the top DEPTH
1/2” chart for height compliance.
of opening down to the sill at the bottom of opening. Reference 1/2”
Configuration Widths Opening Widths 1”
1 1/2”
(Adjustable Width - Use for Step 1b)
2”
(Configuration Ranges)
Opening Heights
Figure 2
36 Configuration
”2/1 34" – 36 3/8" 80" (80" – 80 7/8")
1/2” 1/2”
1/2”32 Configuration
1/2” 31 7/8" – 33 15/16" Also Available in W2 No Modification Required
See Appendix A (Pg. 6) Less than 31 7/8" 78" (78"–78 7/8") or 84" (84"– 84 7/8")
1 1/2” MOUNTING
3. Make sure that the
”2/exterior
1 trim meets the mounting surface requirements to accommodate SURFACE
the retractable insect screen assembly (see Figure 2). The assembly needs 3/4" flat surface on ”8/5
1”
exterior trim face and 3/4" minimum depth of mounting surface. 1” DOOR
1 1/2” 2” 2” H
”2/1 SILL
Figure 3a
CAUTION
”1 ”8/5
If the Door Sill doesn’t extend past the Mounting Surface or doesn’t See Appendix B
have sufficient support, product damage, injury or both may occur. W3
• If the Door Sill extends past your exterior trim Mounting”Surface
2 MOUNTING
1 1/2” and is supported, no modification is required (see Figure 3a). SURFACE
• If the Door Sill is extended without support or not extended (see Figure 3b), ”2/1 1 DOOR
Figure 1 SILL
you will need to add support blocking. See Appendix B (on page 6).
Figure 3b
* Andersen retractable insect screens are designed to be installed on the exterior of the home. However, the door can be installed on the interior
(i.e. for outswing door openings) as long as the opening meets the sizing and mounting surface requirements. For changing handle orientation, see page 7.

2 ”2/1 1
 1 1 KEY REFERENCES
ASSEMBLE 3 1 Screw Flanges

1 SCREEN
TRACKS &
HOUSINGS
4
A

3
2 D

3
2
3
2 Receiving Tabs

3 Letter Labels

Screen Housing Latch Housing Screen Track (A/B) Screen Track (C/D) 4 Fastener Clips

NOTICE
a ALL ITEMS DURING THE ASSEMBLY STEPS
SHOULD BE LAYING FLAT ON THE GROUND RECEIVING TAB
Receiving Tabs on the Endcaps must
(FITS INSIDE SCREEN TRACK)
slide inside the Screen Track. Product

32
CHANNEL damage may occur if Receiving Tab is
forced outside the screen track.

36
(FOR SCREEN TRACK)
A

C C D D ENDCAP A Visit AndersenLuminAire.com/install

to view a video of this step.
A SCREEN
TRACK A
INTERIOR
LABEL FASTENER CLIP
IN OPEN POSITION

SCREEN
TRACK A
INTERIOR
LABEL
A A
A A

36
A

36
RECEIVING TAB RECEIVING TAB SHOULD NOT
A A B B CHANNEL

32
(FOR SCREEN TRACK) (FITS INSIDE SCREEN TRACK) BE OUTSIDE SCREEN TRACK

CORRECT INCORRECT
a1 Unpack the housings and screen tracks onto a non-abrasive surface, with the side labeled Interior facing up. Leaving the screen in the retracted position,
arrange the components so the letters marked on the Screen Tracks and the letters marked on the Endcaps align (A to A, B to B, C to C and D to D).
a2 Confirm the Fastener Clips on endcaps A and C are in the open position. Starting at corner A, slide the Receiving Tab on Endcap A inside the Screen Track.
Ensure the Receiving Tab fits inside the Screen Track, and the Screen Track slides into the Channel. (see “correct” above).
(Visit AndersenLuminAire.com/Install to view a video of this step.)
a3 Repeat for corner C, then continue to corners B and D. They do not have Fastener Clips, which allows the door assembly to adjust to your door opening width.
a4 Use the “36 Configuration” for openings 34 - 36 3/8" wide or “32 Configuration” for openings less than 34" wide in step b.
(If the opening is narrower than 31 7/8" wide, See Appendix A on page 6.)

b 36 Configuration 32 Configuration
(use for opening widths between 34" to 36-3/8") (use for opening widths less than 34")

ENDCAP A ENDCAP A

SCREEN TRACK A OR B TUBING!

IN GK TA
TRAC
SCREEN
RECIDEEIVSLIDES INS SCREEN TRACK A
A A
AA AA
36

32
32

FASTENER CLIP 36" LINE FASTENER CLIP 32" LINE

b1 If the opening is between 34" and 36 3/8", adjust Screen Track A b1 If the opening is less than 34", adjust Screen Track A until 32" line
until 36" line aligns with edge of Endcap A. aligns with edge of Endcap A.
b2 Rotate the Fastener Clip up until it snaps into the closed position. b2 Rotate the Fastener Clip up until it snaps into the closed position.
b3 Repeat steps for side C. b3 Repeat steps for side C.
3
 5/8” 1/2”

5/8” 1/2”
1/2” 1” SMS Pan 5/8” 1/2”

Tools Recommended: SCREW PACK

PLACE AND 1/2”

2
1” 5/8” 1/2”
#8-1"
1 1/2” 2”

FASTEN 1/8" 1” SMS Pan Painted (Qty 6)

ASSEMBLY 1 1/2”
1 1/2” 2”
1”

INTO OPENING Scissors

1” Machine Pan Painted
1 1/2”

a 1-1/2”bMachineTRIM
Flathead

! !#10
SURFACE
DOOR
OPENING

DOOR OPENING DOOR OPENING

HANDLE HANDLE

OR

!
1-1/2” Machine Flathead
SCREEN HOUSING SCREEN HOUSING MOUNTING
5/8” 1/2”
2” SMS Pan Painted
SURFACE

SCREEN

#12 ASSEMBLY 1/2”

5/8” SCREW
1/2” ”2/1
SCREW FLANGE FLANGE

a1 With a Scissors, cut Plastic Wrap

5/8” SMS
b1 ThePan Painted
screen assembly will be narrower than your opening until fully
”2/1 1”
along inside edge of Screw Flange. expanded in the following steps.
1 1/2” 2”
a2 With the interior of the screen b2 Start by placing the Screen Assembly onto the exterior Trim Surface,
assembly facing the door opening, SCISSORS with the Screw Flanges extending into the Door
”2/1 Opening. Rest the
rotate the assembly so the Screen bottom of the screen assembly onto your sill or support blocking.
”1
Housing is on the opposite side b3 Slide the screen assembly in the door opening until the Latch Housing
of the Door Opening Handle. PLASTIC WRAP side Screw Flange is tight to the Mounting Surface.
1 1/2” ”2

”2/1 1

c MOUNTING d
SURFACE
EXPAND
”2/1 1
LATCH SCREEN SCREW
HOUSING HOUSING FLANGE
SCREW
FLANGE
MOUNTING
SURFACE
LATCH
HOUSING
#8 - 1" EXPAND
SCREW

c1 Verify the Latch Housing side Screw Flange is tight to Mounting Surface. d Expand screen assembly by sliding Screen Housing side until the
c2 With 1/8" bit provided, predrill through the three holes on the Latch Screw Flange is tight to the Mounting Surface.
Housing side Screw Flange into the Mounting Surface a maximum
depth of 3/4".
c3 With three of the #8 - 1" screws, fasten Latch Housing side of screen
assembly to the Mounting Surface. (Be careful not to over tighten)

4
2 PLACE AND FASTEN ASSEMBLY - Continued

e f
SCREEN SCREEN
HOUSING HOUSING

SCREW SCREW
LATCH
FLANGE FLANGE

#6 #8 - 1"
SCREW
3/4” Machine Pan Painted
MOUNTING MOUNTING
SURFACE SURFACE
1-1/4” SMS Pan

e From the interior of the screen assembly, hold the Screen Housing side
#8
f1 Verify the screen assembly is plum, level and square in the door opening

! !
Screw Flange against the Mounting Surface, extend the insect screen 1/2”
and theSMS
ScreenPan
Housing side Screw Flange is tight to Mounting Surface.
across the assembly and latch. Orange Installation Clips can come off f2 With 1/8" bit provided, predrill through the three holes on the Screen Housing
and be properly disposed of.
! ! side Screw Flange into the Mounting Surface a maximum depth of 3/4".
f3 1/2” SMS
With the three Pan Painted
remaining #8 - 1" screws, fasten Screen Housing
to the Mounting Surface. (Be careful not to over tighten)
5/8” 1/2”
5/8” 1/2”

5/8” 1/2” 1/2” SMS Flathead

1/2”

SCREW 1/2”
PACK
Tools Recommended:
5/8” 1/2”

3
PLACE AND
1”

#8 - 1/2"
1 1/2” 2”

FASTEN SILL 1/2” Self-Drill Pan

1/8" (Qty 3) 1”
1 1/2” 1 1/2” 2”
ADAPTER
#2 Phillips
1/2” Self-Drill Pan Painted
Sill Adapter 1 1/2”

3/4” Machine Flathead

a SCREEN
TRACK
ADAPTER
CHANNEL
SILL
ADAPTER
DOOR
SILL
b SILL
ADAPTER
DOOR
SILL

7/8” Machine Pan Painted

MAX 1/4"
1” SMS
DEPTH Pan
ADAPTER SILL SILL #8 - 1/2 "
CHANNEL ADAPTER ADAPTER SCREW
1” SMS Pan Painted

SILL DOOR 1” Machine Pan Painted

DOOR DOOR
ADAPTER SILL SILL SILL

Figure 1 Figure 2 1-1/2” Machine Flathead

a1 Thoroughly clean the Door Sill. b1 With 1/8" bit provided, predrill through the three holes on the Sill Adapter
a2 From the interior of screen assembly, position Sill Adapter with the into the Door Sill a maximum depth of 1/4".

#10
textured side up and screw holes in toward the interior of the home. b2 Lift Sill Adapter and apply sealant into predrilled holes until sealant
a3 Insert edge of the Sill Adapter into the Adapter Channel located on over-flows onto Door Sill surface.
the Screen Track (see Figure 1). b3 Rotate the Sill Adapter back down to the Door Sill and fasten using
a4 Rotate the Sill Adapter down to the Door Sill (see Figure 2). three #8 - ½" Self-Tapping Screws. Cleanup excess sealant.
1-1/2” Machine Flathead
a5 Center the Sill Adapter in the door opening.* * 30.5” sill adapter is designed to avoid the need for cutting during installation.
If a wider sill adapter is preferred, visit parts.andersenstormdoors.com

5
2” SMS Pan Painted
 APPENDIX - STEPS FOR NARROW OPENING AND SUPPORT BLOCKING FOR SILL (if required)

APPENDIX A Tools Recommended:

A
Work Gloves
Narrow Opening
Modification for
Hacksaw
Openings less
than 31 7/8" wide. Metal File
Screen Track (A/B) Screen Track (C/D) Sill Adapter Tape Measure

! !!
a EXAMPLE b HACKSAW CUT MARK SQUARE END
(FOR STEP a3 BELOW)

!
W1 SCREEN
If opening width W1 = 29 3/4," TRACK
W2 = 29 3/4," and W3 = 29 1/2."
Take narrowest width = 29 1/2"
and subtract from 32 inches.
W2
32 - 29 1/2 = 2 1/2 inches Figure 1
CALCULATED LENGTH
The Calculated Length of
5/8” 1/2”
material to cut off is 2 1/2
inches5/8”
in this example. HALF CALCULATED 1/2”
HALF CALCULATED
LENGTH LENGTH
For sill adapter (step b3), use 5/8” 1/2”
half the Calculated Length 1/2”
W3
by dividing it by 2.
1/2”
2 1/25/8”
÷ 2 = 1 1/4 inches 1/2” CUT MARK SILL ADAPTER CUT MARK 1”
2”
Figure 2
1 1/2”

a1 To modify screen assembly to work in a Narrow Opening, b1 Measure and mark from Square End of the Screen Track (side B) the Calculated Length.
the Screen Tracks and Sill Adapter need to be cut down.b2 With a Hacksaw make a clean square cut through the Screen Track 1” at the Cut Mark.
1 1/2”
a2 Measure door opening width at top (W1), middle (W2), and With 2”down all sharp edges. Repeat steps for the other Screen Track
a metal file, file
1 1/2”
bottom (W3) from the inside of the exterior trim. (side D) (see Figure 1).
a3 Calculate Length of material to be cut off by taking the b3 Measure and mark from each end of the Sill Adapter the Halved Calculated Length
narrowest width from above and subtracting it from 32 so equal amounts are removed from both sides (see Figure 2).
inches (see Example above). b4 With the Hacksaw make a clean square cut through the Sill Adapter on both ends at the
Cut Marks. With a metal file, file down all sharp edges. Return to Measure on Page 2.
1 1/2”

B APPENDIX B – Support Blocking for Door Sill

C APPENDIX C – Outswing Door Openings

a Andersen retractable insect screens are designed to be installed
on the exterior of the home. However, the door can be installed on
the interior (i.e. for outswing door openings) as long as the opening
meets the sizing and mounting surface requirements.
DOOR SILL Handle orientation can be reversed by unscrewing the Interior
EXTEND Handle and reassembling in the rotated reversed configuration.
3/4" MIN MOUNTING Take care to align the Latch Plate with the Handle Spindles when
SURFACE reassembling. For more details, see figure 3 on Page 7.

SUPPORT
BLOCKING

a1 Choose Support Blocking the width of the Door Sill with enough depth
to Extend 3/4" Minimum out from the exterior trim Mounting Surface.
a2 Center the Support Blocking under the sill and make sure it is level and
parallel to the sill. Confirm it Extends 3/4" Minimum from Mounting Surface.
a3 Properly secure Support Blocking below the Sill.
Return to Measure on Page 2.
6
 FREQUENTLY ASKED QUESTIONS – ANDERSEN® LUMINAIRE™ RETRACTABLE INSECT SCREEN

1. How do I open and close the insect screen? Unlatching Locking/Unlocking

Use the Handle to extend insect screen to the other side of door frame. It will
automatically latch when fully extended. Slide the Release Lever up or down RELEASE LOCK
to unlatch, the insect screen will automatically retract (see Figure 1). LEVER TAB

2. How do I lock and unlock the insect screen?

To lock the insect screen door, move the Lock Tab toward the screen assembly. INTERIOR INTERIOR
To unlock, move the Lock Tab away from the screen assembly (see Figure 2). HANDLE HANDLE

3. What should I do to maintain my retractable insect screen door? Figure 1 Figure 2

The screen tracks will need occasional vacuuming to remove dirt and debris.
This will help keep the tracks clean and free of debris that may affect operation. Reverse Handle

4. Can the handle be reversed so the locking tab is on the other side of the door? HANDLE HANDLE
SPINDLES SPINDLES
The handle can be removed and reversed by unscrewing the Interior Handle and
reassembling in the rotated reversed configuration. Take care to align the Latch Plate
with the Handle Spindles when reassembling (see Figure 3).
HANDLE
5. Can the fastener clips be opened if I closed them in the wrong SCREWS
LATCH
position during installation? PLATE
You can open the fastener clip by applying downward pressure
with a flat blade screwdriver until it releases open (see Figure 4). INTERIOR EXTERIOR
HANDLE HANDLE
6. Can replacement parts be purchased if something gets damaged on my door? Figure 3
Parts can be purchased by visiting parts.andersenstormdoors.com or calling Customer
Service at 844-813-6664. It is helpful to have your serial number when ordering parts. The Opening Fastener Clip
serial number is located near Endcap A on your screen housing.
FLAT BLADE SCREWDRIVER
7. The door is not latching consistently, is there an adjustment that can be made?
The Striker can be adjusted to assist with more consistent latching of the unit. Loosen the
Striker Screws and slide the Striker up or down accordingly, retighten screws (see Figure 5).
TUBING!
B CK TA
TRAG
IN SCREEN
RECIDEEIV
SLIDES INS

8. What should I do with the unit in cold weather? A

It is best for the unit to be stored in the retracted position during cold weather. We do not AA

32
recommend operating when temperatures are near or below freezing.

9. Why is the sill adapter narrower than the door opening? FASTENER CLIP IN CLOSED POSITION

The sill adapter provided is designed to avoid the need for cutting for most door opening Figure 4
widths. A wider sill adapter can be ordered at parts.andersenstormdoors.com or by calling
Customer Service at 844-813-6664. Striker Adjustment

10. Is there a video available that will show me how to install and operate the door?
You can find a video of how to install and operate the retractable insect screen door at
AndersenLuminAire.com/install

STRIKER STRIKER
SCREWS

Figure 5

For additional assistance visit ANDERSENLUMINAIRE.COM or Customer Service: 844-813-6664

7
LIMITED WARRANTY

ANDERSEN® LUMINAIRE™ RETRACTABLE SCREEN DOOR 5 YEAR LIMITED WARRANTY

LIMITED WARRANTY ON RETRACTABLE SCREEN DOOR COMPONENTS

Emco Enterprises LLC (Emco), an Andersen company, warrants the screen housing, latch housing, screen track, endcap and sill adapter
components of the Andersen® LuminAire™ retractable screen door to be free from defects in manufacturing, materials, paint adhesion, and
workmanship, under normal conditions, for five (5) years from the date of purchase or as long as the original consumer purchaser owns the
home in which the door was initially installed, whichever is shorter.

In the event a screen housing, latch housing, screen track, endcap or sill adapter fails as a result of a defect in manufacturing, materials or
workmanship within the limited warranty period specified above, and upon written proof of purchase, Emco, will at its option refund or
provide a replacement screen housing, latch housing, screen track, end cap or sill adapter without charge – installation is not included.
Such replacement is warranted for the remainder of the original limited warranty period. Please locate the door serial number and written
proof of purchase then contact Emco Consumer Support at 1-844-813-6664.

NO OTHER WARRANTIES OR REPRESENTATIONS

THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ALL WARRANTIES ARE LIMITED TO THE APPLICABLE
STATUTE OF LIMITATIONS, BUT IN NO CASE WILL EXTEND BEYOND THE LIMITED WARRANTY PERIODS SPECIFIED ABOVE. EMCO EXCLUDES
AND WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES, WHETHER ARISING OUT OF CONTRACT, TORT OR
OTHERWISE. THE REMEDY OF REPLACEMENT OF THE PRODUCT PROVIDED BY THIS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY WITH
RESPECT TO AND ANY AND ALL LOSS OR DAMAGE.

APPLICABLE LAW
This Limited Warranty is only applicable in the U.S.A. (i.e. the fifty states and the District of Columbia). This Limited Warranty gives you
specific legal rights, and you may have other rights which vary from state to state or province. Some states do not allow the exclusion
or limitation of incidental or consequential damages or limitation of the duration of an implied warranty, so the above limitations or
exclusions may not apply to you. If any specific term of this Limited Warranty is prohibited by any applicable law, it shall be null and void,
but the remainder of this Limited Warranty shall remain in full force and effect.

WHAT IS NOT COVERED BY THIS LIMITED WARRANTY

Damage caused by:
• Improper installation (including failure to follow installation instructions), modification, maintenance, or use
• Chemicals or airborne pollutants, such as salt or acid rain
• Acts of God, including wind damage
• Accidents
• Normal wear and tear
• Products not manufactured by Emco

Emco Enterprises LLC is a wholly owned subsidiary of Andersen Corporation. Emco manufactures and supports the limited warranties
covering Andersen® and EMCO® Storm and Screen Doors. “Andersen” “EMCO” and all other marks where denoted are trademarks of
Andersen Corporation. ©2017 Andersen Corporation. All rights reserved.
Reprinted and effective as of September 12, 2017.