Click Here for Engineering Thermodynamics full study material.

VALLIAMMAI ENGINEERING COLLEGE

DEPARTMENT OF MECHANICAL ENGINEERING
QUESTION BANK
ME 8391 - ENGINEERING THERMODYNAMICS

UNIT I

BASIC CONCEPT AND FIRST LAW

PART - A

1. What do you understand by pure substance?

2. Define thermodynamic system.
3. Name the different types of system.
4. Define thermodynamic equilibrium.
5. What do you mean by quasi-static process?
6. Define Path function.
7. Define point function.
8. Explain homogeneous and heterogeneous system.
9. What is a steady flow process?
10. Prove that for an isolated system, there is no change in internal energy.
11. Indicate the practical application of steady flow energy equation.
12. Explain Mechanical equilibrium.
13. Explain Chemical equilibrium.
14. Explain Thermal equilibrium.
15. Define Zeroth law of Thermodynamics.
16. What are the limitations of first law of thermodynamics?
17. What is perpetual motion machine of first kind?
18. Differentiate between Microscopic and Macroscopic?
19. Differentiate Quasi static and non Quasi static process?
20. Differentiate reversible process and irreversible process?

PART – B

1. a) A rigid tank containing 0.4m3 of air at 400 kPa and 30oC is connected by a valve
to a piston cylinder device with zero clearance. The mass of the piston is such that a
pressure of 200 kPa is required to raise the piston. The valve is opened slightly and
air is allowed to flow into the cylinder until the pressure of the tank drops to 200
kPa. During this process, heat is exchanged with the surrounding such that the
entire air remains at 30oC at all times. Determine the heat transfer for this process.

b) A reciprocating air compressor taken in 2m 3/min air at 0.11MPa, 293K which it

delivers at 1.5 Mpa, 384 K to an after cooler where the air where the air is cooled
at constant pressure to 298 K. the power absorbed by the compressor is 4.15 kW.

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

Determine the heat transfer in (i) the compressor (ii) the cooler. State your
assumptions.

2. In a turbo machine handling an incompressible fluid with a density of 1000kg/m 3

the conditions of the fluid at the rotor entry and exit are as given below:
1. Inlet Exit
Pressure 1.15 MPa 0.05MPa
Velocity 30 m/sec 15.5 m/sec
Height above datum 10 m 2m
If the volume flow rate of the fluid is 40 m3/s, estimate the net energy transfer from
the fluid as work.
3. Three grams of nitrogen gas at 6 atm and 160oC is expanded adiabatically to double
its initial volume and then compressed again at constant volume to its initial state.
Calculate the work done on the gas. Draw the p-V diagram for the process. Specific
heat ratio of nitrogen is 1.4.
4. Describe steady flow energy equation and
 deduce suitable expression for the expansion of gas in a ga turbine
with suitable assumptions.
 apply the equation to a nozzle and derive an equation for velocity at
exit.
 Derive the suitable expression for the ideal compressor and specify the
assumptions onder which such equation is aplicable.
5. a) Air expands isentropic process through a nozzle from 784 kPa and 220 oC to an
exit presssure of 98 kPa. Detrmine the exit velocity and the mass flow rate, if the exit
area is 0.0006m2.
b) In an air compressor, air flows steadily at the rate of 0.5 kg/sec. At entry to the
compressor, air has a pressure of 105 kPa and specific volume of 0.86 m3/kg and at
exit of the compressor those corresponding values are 705 kPa and 0.16 m3/kg.
neglect kinetic and potential energy change. The internal energy of air leaking the
compressor is 95 kJ/kg greater than that of air entering. The cooling water in
the compressor absorbs 60 kJ/sec. of heat from the air. Find power required to
drive the compressor.
6. Air contained in the cylinder and piston arrangement comprises the system. A cycle
is completed by four process 1-2, 2-3, 3-4 and 4-1. The energy transfers are listed
below. Complete the table and determine the network in kJ. Also check the validity
of the first law of thermodynamics.

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

Process Q (kJ) W (kJ) ΔU (kJ)

1-2 40 ? 25
2-3 20 -10 ?
3-4 -20 ? ?
4-1 0 +8 ?

7. Calculate the power developed and diameter of the inlet pipe, if a gas enters into the
gas turbine at 5 kg/sec, 50 m/s with an enthalpy of 0.9MJ/kg. the heat loss to the
surrounding is 0.025 MJ/kg. the heat loss to the surrounding is 0.025 MJ/kg. the
heat loss to the surrounding is 0.025 MJ/kg. assume 100 kPa and 300 K at the inlet.
8. a. Define the following terms:
 Thermodynamics
 Macroscopic approach
 Continuum
b. A gas of mass 1.5 kg undergoes a quasistatic expansion, which follows a
relationship P=a+bV, where ‘a’ and ‘b’ are constants. The initial and final
pressures are 1000 kPa and 200 kPa respectively and the corresponding volumes
are 0.2 m3 and 1.2 m3. The specific internal energy of the gas is given by the
relation U = (1.5PV – 85) kJ/kg, where P is in kPa and V is in m3. Calculate the
net heat transfer and the maximum internal energy of the gas attained during
expansion.
9. a) Define enthalpy. How is it related to internal energy?
b) A fluid is confined in a cylinder by a spring loaded, frictionless piston so that the
pressure in the fluid is a linear function of the volume (p = a + bV) where U is in kJ,
p is in kPa and V in cubic meter. If the fluid changes from an initial state of 170
kPa, 0.03 m3 to a final state of 400 kPa, 0.06 m3, with no work other than that done
on the piston, find the direction and magnitude of the work and heat transfer.
10. The electric heating system used in many houses consists of simple duct with
resistance wire. Air is heated as it flows over resistance wires. Consider a 15 kW
electric heating system. Air enters the heating section at 100 kPa and 17oC with a
volume flow rate of 150 m3/min. if heat is lost from the air in the duct to the
surroundings at a rate of 200 W, determine the exit temperature of air.

UNIT II

SECOND LAW AND AVAILABILITY ANALYSIS

PART - A

1. Define Clausius statement.

2. What is Perpetual motion machine of the second kind?
3. Define Kelvin Planck Statement.
4. Define Heat pump.
5. Define Heat engine.

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

6. What are the assumptions made on heat engine?

7. State Carnot theorem.
8. What is meant by reversible process?
9. What is meant by irreversible process?
10. Explain entropy?
11. Define availability.
12. Define available energy and unavailable energy.
13. Explain the term source and sink.
14. What do you understand by the entropy principle?
15. What are the important characteristics of entropy?
16. What is reversed Carnot heat engine? What are the limitations of carnot cycle?
17. Why Rankine cycle is modified?
18. Name the various vapour power cycle.
19. Define efficiency ration.
20. Define overall efficiency.

PART – B

1) Air is compressed by an adiabatic compressor from 100 kPa and 12 oC to a pressure

of 800 kPa at a steady rate of 0.2 kg/s. if the isentropic efficiency of the compressor
is 80 percent, determine the exit temperature of air and the required power input to
the compressor.
2) a) A 200 m3 rigid tank initially contains atmospheric air at 100 kPa and 300 K and is
to be used as storage vessel for compressed air at 1 MPa and 300 K. Compressed air
is to be supplied by a compressor that takes in atmospheric air at Po = 100 kPa and
To = 300 K. determine the minimum work required for this process.
b) The interior lighting of refrigerators is provided by incandescent lamps whose
switches are actuated by the opening of the refrigerator door. Consider a
refrigerator whose 40 W light bulp remains on continuously as a result of a
malfuntion of the switch. If the refrigerator has a co efficient performance of 1.3
and the cost of electricity is Rs. 8 per kWh, determine the increase in the energy
consumptionof the refrigerator and its cost per year if the switch is not fixed.
3) a. A carnot heat engine receives 650 kJ of heat from a source of unknown
temperature and rejects 250 kJ of it to a sink at 297 K. determine the temperature
of the source and the thermal efficiency of the heat engine.
b. A carnot heat engine receives heat from a reservoir at 1173 K at a rate of 800
kJ/min and reject the waste heat to the ambient air at 300 K. the entire work output
of the heat engine is used to drive a refrigerator that removes heat from the
refrigerated space at 268 K and transfers it to the same ambient air at 300 K.
determine the maximum rate of the heat removal from the refrigerated space and
the total rate of heat rejection to the ambient air.
4) a. what are the conditions for reversibility? Explain.
b. An heat exchanger circulates 5000 kg/hr of water to cool oil from 150 oC to 50oC.
The rate of flow of oil is 2.5 kJ/kg.K. the water enters the heat exchanger at 21 oC.
Determine the net change in entropy due to heat exchange process, and the amount

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

of work obtained if cooling of oil is done by using the heat to run a carnot engine
with sink temperature of 21oC.
5) a. deduce clausius inequality and interpret it.
b. An ideal gas of 0.12 m3 is allowed to expand isentropically from 300 kPa and
120oC to 100 kPa, 5 kJ of heat is then transferred to the gas at constant pressure.
Calculate the change in entropy for each process. Assume γ=1.4 and Cp=1.0035
kJ/kg.K. if these two processes are replaced by a reversible polytropic expansion,
find the index of expansion between original and final states. What will be the total
changes in entropy?
6) a) A heat engine operating between two reservoirs at 100 K and 300 K is used to
drive heat pump which extracts heat from the reservoir at 300 K at a rate twice that
at which engine rejects heat to it. If the efficiency of the engine is 40 % of the
maximum possible and the co efficient of performance of heat pump is 50 % of the
maximum possible, make calculations for the temperature of the reservoir to which
the heat pump rejects heat. Also work out the rate of heat rejection from the heat
pump if the rate of supply of heat to the engine is 50 kW.
b) Two kg of air at 500 kPa, 80oC expands adiabatically in a closed system until its
volume is doubled and its temperature becomes equal to that of the surroundings
which is at 100 kPa, 5oC for this process, determine
The maximum work
The change in availability and
The irreversibility
For air taken, Cv = 0.718 kJ/kg. K, u=Cv T where Cv is constant and Pv =
mRT where P is pressure in kPa, V volume in m3, ‘m’ mass in kg, R a
constant equal to 0.287 kJ/kg K and T temperature in K.
7) a. deduce the efficiency of carnot cycle in terms of temperature from its p-V
diagram.
b. Air is compressed from 100 kPa and 300 K to 5 bar isothermally and then it
receives heat at constant pressure. It is finally returns to its initial condition by a
constant volume path. Plot the cycle on p-V and T-s diagram and calculate the net
heat and work transfer.
8) a) Bring out the concept of entropy and importance of T-s diagram.
b) Five kg of water at 303 K is mixed with one kg of ice at 0 oC. The system is open to
atmosphere. Find the temperature of the mixture and the changr of entropy for
both ice and water. Assume Cp of water as 4.18 kJ/kg-K and latent heat of ice as
334.5 kJ/kg. comment on the result based on the principle of increase in entropy.
9) a) define the tem ‘Irreversible process’ and ‘Reversible process’. Give an example of
each.
b) In a Carnot cycle the maximum pressure and temperature are limited to 18 bar
and 410oC. The volume ratio of isentropic compression is 6 and isothermal
expansion is 1.5. assume the volume of the air at the beginning of isothermal
expansion as 0.18m3. show the cycle on p-V and T-s diagrams and determine
 the pressure and temperature at main points
 thermal efficiency of the cycle

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

10) a. State and prove Clausius inequality.

b. A metal block with m = 5 kg, c = 0.4 kJ/kg.K at 40oC is kept in a room at 20oC. It
is cooled in the following two ways:
 Using a Carnot engine (executing integral numbeer of cycles) with the
room itself as the cold reservoir;
 Naturally
In each case, calculate the changes in entropy of the block, of the air of the room
and of the universe. Assume that the metal block has constant specific heat.

UNIT III

PROPERTIES OF PURE SUBSTANCE AND STEAM POWER CYCLE

PART - A

1. Define specific steam consumption of an ideal Rankine cycle.

2. Name the different components in steam power plant working on Rankine cycle.
3. What are the effects of condenser pressure on the Rankine Cycle?
4. Mention the improvements made to increase the ideal efficiency of Rankine cycle.
5. Why reheat cycle is not used for low boiler pressure?
6. What are the disadvantages of reheating?
7. What are the advantages of reheat cycles?
8. Define latent heat of evaporation or Enthalpy of evaporation.
9. Explain the term super heated steam and super heating.
10. Explain heat of super heat or super heat enthalpy.
11. Explain the term critical point, critical temperature and critical pressure.
12. Define dryness fraction (or) What is the quality of steam?
13. Define enthalpy of steam.
14. How do you determine the state of steam?
15. Define triple point.
16. Define heat of vaporization.
17. Explain the terms, Degree of super heat, degree of sub-cooling.
18. What is the purpose of reheating?
19. Why are the temperature and pressure dependent properties in the saturated mixture
region?
20. what are the four processes that make up the simple ideal rankine cycle?

PART – B

1. a) A 0.5 m3 vessel contains 10 kg refrigerant 134a at -20oC. Determine the pressure,

the total internal energy and the volume occupied by the liquid phase.
b) A rigid tank with a volume of 2.5 m3 contains 15 kg of saturated liquid vapour
mixture of water at 75oC. Now the water is slowly heated. Determine the
temperature at which the liquid in the tank is completely vapourized. Also, show the
processes on T-v diagram with respect to saturation lines.

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

2. Consider a steam powerplant that operates on a reheat rankine cycle ans has a net
power output of 80MW. Steam enters the high pressure turbine at 10MPa and
500oC and the low pressure turbine at 1 MPa and 500 oC. Steam leaves the
condenser as a saturated liquid at a pressure of 10kPa. The isentropic efficiency of
the turbine is 80 percent, and that of the pump is 95 percent. Show the cycle on a T-s
diagram with respect to saturation lines, and determine
 The quality (or temperature, if superheated) of the steam at the
turbine exit,
 The thermal efficiency of the cycle, and
 The mass flow rate of the steam.
3. In a closed vessel the 100 kg of steam at 100 kPa, 0.5 dry is to be brought to a
pressure of 1000 kPa inside vessel. Determine the mass of dry saturated steam
admitted at 2000 kPa for raising pressure. Also determine the final quality.
4. A steam power plant running on Rankine cycle has steam entering HP turbine at 20
MPa, 500oC and leaving LP turbine at 90% dryness. Considering condenser
pressure of 0.005 MPa and reheating occuring up to the temperature of 500 oC
determine,
 The pressure at which steam leaves HP turbine
 The thermal efficiency.
 Work done
5. Consider a steam power plant operating on the ideal Rankine cycle. Steam enters
the turbine at 3 MPa and 623 K and is condensed in the condenser at a pressure of
10 kPa. Determine (i) the thermal efficiency of this power plant, (ii) the thermal
efficicency if steam is superheated to 873 K instead of 623 K, and (iii) the thermal
efficiency if the boiler pressure is raised to 15 MPa while the turbine inlet
temperature is maintained at 873 K.
6. Consider a steam power plant operating on the ideal reheat Rankine cycle. Steam
enters the high pressure turbine at 15 MPa and 873 K and is condensed in the
condenser at a pressure of 10 kPa. If the moisture content of the steam at the exit of
the low pressure turbine is not to exceed 10.4 percent, determine (i) the pressure at
which the steam should be reheated and (ii) the thermal efficiency of the cycle.
Assume the steam is reheated to the inlet temperature of the high pressure turbine.
7. a) Draw p-T diagram and label various phases and transitions. Explain the process
of isobaric heating above triple point pressure with the help of p-T diagram.
b) 2 kg of water at 200oC are contained in a 20m3 vessel. Determine the pressure,
enthalpy, mass and volume of vapour within the vessel.
8. a) Draw rankine cycle with one open type feed water heater. Assume the condition
of the steam before entering the turbine to be superheated. Sketch the cycle on T-s
diagram.
b) in an ideal reheat cycle, the steam enters the turbine at 30 bar and 500 oC after
expansion to 5 bar, the steam is reheated to 500oCand then expanded to the
condenser pressure of 0.1 bar. Determine the cycle thermal efficiency, mass flow
rate of steam. Take power output as 100 MW.

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

9. In a single heater regenerative cycle the steam enters the turbine at 30 bar, 400oC
and the exhaust pressure is 0.10 bar. The feed water heater is a direct-contact type
which operates at 5 bar. Find
 The efficiency and the steam rate of the cycle, and
 The increase in mean temperature of heat addition, efficiency and
steam rate as compared to the rankine cycle (with out re generation)
neglect pump work.
10. One kg of steam is contained in an elastic baloon of spherical shape which supports
an internal pressure proportional to its diameter. The initial condition of steam is
saturated vapour at 110oC heat is transferred to steam until pressure reaches 200
kPa. Determine:
 Final temperature
 Heat transferred. Take Cps = 2.25 kJ/kg.K

*****************************

UNIT IV

IDEAL AND REAL GASES AND THERMODYNAMIC RELATIONS

1. Define Ideal gas.

2. Define Real gas.
3. What is equation of state?
4. State Boyle’s law.
5. State Charle’s law.
6. Explain the construction and give the use of generalized compressibility chart.
7. What do you mean by reduced properties?
8. Explain law of corresponding states.
9. Explain Dalton’s law of partial pressure.
10. State Avogadro’s Law.
11. What is Joule-Thomson coefficient?
12. What is compressibility factor?
13. What is partial pressure?
14. Define Dalton’s law of partial pressure.
15. How does the Vander Waal’s equation differ from the ideal gas equation of state?
16. Using the definition of mass and mole fractions derive a relation between them?
17. What is significance of compressibility factor?
18. Write the maxwell equation and its significance?
19. Is water vapour is ideal gas? Why?
20. In atmospheric air (at 101325 Pa) contains 21% oxygen and 79% nitrogen (vol. %),
what is the partial pressure of oxygen?

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

PART – B

1) a) A rigid tank contains 2 k mol of N2 and 6 k mol of CO2 gases at 300 K and 15
MPa. Estimate the volume of the tank on the basis of
 The ideal gas equation of state
 Compresibility factors and Amagat’s law, and
 Compressibility factors and Dalton’s law.
b) An insulated rigid tank is divided into two compartments by a partition. One
compartment contains 7 kg of oxygen gas at 40oC and 100 kPa, and the other
compartment contains 4 kg of nitrogen gas at 20oC and 150 kPa. Now the partition
is removed, and the two gases are allowed to mix. Determine
 the mixture temperature
 the mixture pressure after equlilibrium has been established.
2) a) Using the ideal gas equation of state, verify
 the cyclic relation and
 the reciprocity relation at constant P.
b) Show that the internal energy of an ideal gas and an incompressible substance is
a function of temperature only, u = u (T).
c) Derive expression ( and ( in terms of P,v, and T only.
3) In 5 kg of mixture of gases at 1.013 bar and 300 K the various constituents gases are
as follows, 80% N2, 18% O2, 2% CO2. Determine the specific heat at constant
pressure, gas constant for the constituents and mixture and also molar mass of
mixture taking γ = 1.3 for CO2 universal gas constant = 8314 J/kg.K.
4) Derive the Clausius Clapeyron equation and Vander Waal’s equations.
5) a) Using the Claypeyron equation. Estimate the value of the enthalpy of
vapourization of refrigerant R-134a at 293 K, and compare it with the tabulated
value.
b) Show that Cp – Cv = R for an ideal gas.
6) a) Show that the Joule – Thomson co efficient of an ideal gas is zero.
b) Using the cyclic relation and the first Maxwell relation, derive other three
Maxwell relations.
7) a) Deduce the Maxwell relations
b) Explain joule thompson effect with the help of T-p diagram and derive the
expression for Joule Thompson co efficient. Show that the value of this co efficient
for an ideal gas is zero.
8) a) what are the differences between real and ideal gases?
b) write down the Vander Waal’s equation of state for real gases and how is it
obtained from ideal gas equation by incorporating real gas corrections?
c) A tank contains 0.2m3 of gas mixture composed of 4 kg of Nitrogen, 1 kg of
oxygen and 0.5 kg of carbon-di oxide. If the temperature is 20oC, determine the total
pressure, gas constant and molar mass of the mixture.

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

9) a) Entropy is a function of any two properties like P and V, P and T etc., for a pure
substance with the help of Maxwell’s Equation. Prove
 Tds = Cv.dT + T [ß/k].dv
 Tds = Cv.dT – V.ßdp.T
 Tds = [K Cv/ß].dp + [Cp/vß].dv.
b) Determine chage of Internal energy and change of entropy when the gas obeys
Vander Waal’s equation.
10) a) write down the Dalten’s law of partial pressure and explain its importance.
b) 0.45 kg of CO and 1 kg of air iscontained in a vessel of volume 0.4 m3 at 15oC.
Air has 23.3% of O2 and 76.7% of N2 by mass. Calculate the partial pressure of
each constituents and total pressure in the vessel. Molar masses of CO,O2 and N2
are 28, 32 and 28 kg/k mol.

UNIT V

GAS MIXTURES AND PSYCHROMETRY

PART – A

1. What is humidification and dehumidification?

2. Differentiate absolute humidity and relative humidity.
3. What is effective temperature?
4. Represent the following psychometric process using skeleton psychometric chart?
5. Define Relative humidity.
6. Define degree of saturation.
7. What is meant by dry bulb temperature (DBT)?
8. What is meant by wet bulb temperature (WBT)?
9. Define dew point depression.
10. What is meant by adiabatic saturation temperature (or) thermodynamic wet bulb
temperature?
11. Define sensible heat and latent heat.
12. What are the important psychometric process?
13. What is meant by adiabatic mixing?
14. What are the assumptions made in Vander Waal’s equation of state?
15. Define coefficient of volume expansion.
16. State Helmholtz function.
17. What are thermodynamic properties?
18. Define throttling process.
19. Define isothermal compressibility.
20. Define psychometric.

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

PART – B

[1] a) A 5m x 5m x 3m room contains air at 25oC and 100 kPa at a relative humidity of
75 percent. Determine
 The partial pressure of dry air,
 The specific humidity
 The enthalpy per unit mass of the dry air, and
 The masses of the dry air and water vapour in the room
b) the dry and the wet bulp temperatures of atmospheric air at 1 atm (101.325 kPa)
pressure are measured with a sling psychrometer and determined to be 25 oC and
15oC respectively. Determine
 the specific humidity
 the relative humidity
 the enthalpy per unit mass of the dry air, and
 the masses of the dry air and water vapour in the room.
[2] a) What is sensible heat? How is the sensible heat loss from a human body affected
by the
 skin temperature
 environment temperature, and
 air motion.
b) Saturated air leaving the cooling section of an air conditioning system at 14o C at
a rate of 50 m3/min is mixed adiabatically with the outside air at 32 oCand 60 percent
relative humidity, at a rate of 20 m3/min. assuming that the mixing processes occurs
at a pressure of 1 atm, determine the specific humidity, the relative humidity, the
dry bulb temperature, and the volume flow rate of the mixture.
[3] a) For the atmospheric air at room temperature of 30 oC and relative humidity of
60%. Determine partial pressure of air, humidity ratio,dew point temperature,
density and enthalpy of air.
b) Two streams of moist air, one having flow rate of 3 kg/s at 30 oC and 30% relative
humidity, other having flow rate of 2 kg/s at 35oC and 85% relative humiddity get
mixed adiabatically. Determine specific humidity and partial pressure of water
vapour after mixing. Take Cp; stream = 1.86 kJ/kg.K
[4] a) What is the lowest temperature that air can attain in an evaporative cooler if it
enters at 1 atm, 302 K, and 40 percent relative humidity?
b) consider a room tjat contains air at 1 atm, 308 K, and 40% relative humidity.
Using the psychrometric chart, determine: the specific humidity, the enthalpy, the
wet bulb temperature, the dew point temperature and the specific volume of the air.
[5] An air conditioning system is to take in outdoor air at 263 K and 30 percent relative
humidity at a steady rate of 45 m3/min and to condition it to 298 K and 60 percent
relative humidity. The outdoor air is first heated to 295 K in the heating section and
then humidified by the injection of hot steam in the humidifying section. Assuming the
entire process takes place at a pressure of 100 kPa, determine (i) the rate of heat supply
in the heating section and (ii) the mass flow rate of the steam required in the
humidifying section.

www.BrainKart.com
Click Here for Engineering Thermodynamics full study material.

[6] a) Draw the psychrometric chart and show any two psychrometric processes on it.
b) A sample of moist air at 1 atm and 25oC has a moisture content of 0.01% by
volume. Determine the humidity ratio, the partial pressure of water vapour, the degree
of saturation, the relative humidity and the dew point temperature.
[7] a) Describe the process of adiabatic mixing of two streams in terms of humidity and
/ or enthalpy.
b) The temperature of the windows ina house on a day in winter is 5oC. When the
temperature in the room is 23oC, and the barometric pressure is 74.88 cm Hg, what
would be the maximum relative humidity that could be maintained in the room without
condensation on the windows panes? Undr these conditions, find the partial pressure of
the water vapour and air, the specific humidity and the density of the mixture.
[8]a) The atmospheric air at 30oC DBT and 75% RH enters a cooling coil at the rate of
200 m3/min. the coil dew point temperature is 14oC and the by pass factor is 0.1
determine
 The temperature of air leaving the coil
 Capacity of the cooling coil in TR
 The amount of water vapour removed.
 Sensible heating factor for the process.
b) The volume flow rate of air is 800 m3/min of re circulated at 22oC DBT and 10oC
dew point temperature is to be mixed with 300 m3/min of fresh air is 30oC DBT and
50% RH. Determine the enthalpy, specific volume, humidity ratio and dew point
temperature of the mixture.
[9] a) Differentiate between
 Dry bulb temperature and wet bulb temperature
 Wet bulb depression and dew point depression
b) Air at 16oC and 25oC relative humidity passes through a heater and then through
a humidfier to reach final dry bulb temperature of 30 oC and 50% relative humidity.
Calculate the heat and moisture added to the air. What is the sensible heat factor.
[10] a) In an adiabatic mixing of two streams, derive the relationship among the ratio of
mass of streams, ratio of enthalpy change and ratio of specific humidity change.
b) Saturate air at 20oC at a rate of 1.167 m3/sec is mixed adiabatically with the
outside air at 30oC and 50% relative humidity at a rate of 0.5 m3/sec. assuming
adiabatic mixing condition of 1 atm, determine specific humidity, relative humidity,
dry bulb temperature and volume flow rate of the mixture.

www.BrainKart.com