Scribd
Upload
4K views14 pages

AMOS Command Guide

The document provides commands for checking the status and functions of BTS, RRUs, cells, carriers, and other network elements in an OSS command line interface. Some key commands are to check the status of RRUs (st rru), cells (st cell), carriers (st car), and Ethernet ports (lst eth). It also lists commands for restarting sites and individual units within a site.

Uploaded by

Mohd Zalhariz Mahamad Zaihan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
4K views14 pages

AMOS Command Guide

The document provides commands for checking the status and functions of BTS, RRUs, cells, carriers, and other network elements in an OSS command line interface. Some key commands are to check the status of RRUs (st rru), cells (st cell), carriers (st car), and Ethernet ports (lst eth). It also lists commands for restarting sites and individual units within a site.

Uploaded by

Mohd Zalhariz Mahamad Zaihan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 14

Login to OSSRC

Right click => Open Terminal

Command Prompt> amos <Site id/name>

eg: BB1_B061F_B01524OD_MSJDSAUJANAU
> lt all

Username: celcomrbs

Node Password: Zeti8FNa_019

To check external alarm > alt

To check ret/Antenna > st ret


To check status of RRU > st rru

To check more detail on RRU > get <proxy id>

To check carrier > st car


To check RRU connection > st rilink

To list TRX > lst trx

To check status of cell and sector > lst gsm


To lock RRU/RET/CELL > bl xx xx xx <proxy>

To unlock RRU/RET/CELL >deb xx xx xx <proxy>

To check status of gsm sector/2G > pdiff gsm

Note: To check traffic channel for 2G, please use Command Handling, run RLCRP@RLSLP:CELL=Gxxxxx;
To check BTS frequency > lget bts arfcn

To check status of cell > st cell/fdd

To check status of eNodeB sector > st sector


To block RRU > bl <proxy>

To deblock RRU > deb <proxy>

To check traffic for LTE/4G >ue print -admitted

To verify connection between eNodeB and MME (S1-Control plane) > st mme
To check transport (TN_A – electrical TN_B – optical) > get ethernetport=

To check status of ethernet port > lst eth


To list out of all ip address > lpr router
To ping test > mcc router=TN_RAN ping –count 50 10.231.212.17

> mcc router=TN_RAN ping –count 50 packetsize --1500 <ip address>

> mcc router=TN_LTE ping –count 50 <ip address>

> mcc router=TN_RAN ping –count 50 <ip address>


BB2_B061F_B01524OD_MSJDSAUJANAU
Command Prompt> amos <site id/name>

> lt all

Username: celcomrbs

Node Password: Zeti8FNa_019


To check BTS/NODEB function > pr function

To check status of RRU > st rru

To check more detail on RRU > get<proxy id>


To check user traffic > get radio no

To check status of cell > st cell


To restart site/BB> pr replace

acc <proxy id> restartunit

To restart BB (fallback cv) > cvre <last id cv>

To verify hardware status > invh

To check software version > cvls

Shows all boards installed in the NodeB > cabx

2G G9 G18
BB1 4G L18 L26

3G U21 S1 S2 S3
BB2 U9 S1 S2 S3

3G U21 S3 S4 S5 S6 Puteh C4
BB3

You might also like