North Maharashtra University, Jalgaon

S.Y.B.Sc. Electronics
Paper I (Semester - I)
ELE 231: Analog Circuits and Applications
Unit 1: Single Stage Amplifier: (07P, 06M)
Classification of Amplifier, Single stage Common Emitter Amplifier and its design, Tuned Amplifier,
Distortion and noise in amplifier.
Unit 2: Multistage Transistor Amplifiers: (14P, 12M)
Introduction, Block diagram of multistage transistor amplifier, Application of multistage
amplifier, Block Diagram of PA system, Explanation of terms - gain, frequency response,
decibel gain, Bandwidth. Two stage RC-coupled transistor amplifiers and their design, two stage
transformers coupled transistor amplifier, two stage Direct Coupled Amplifier.
Unit 3: Transistor Power Amplifier: (14P, 12M)
Difference between voltage and power amplifiers, Block diagram of a practical power amplifier,
Classification of power amplifier, Principle of push pull amplifier, Class B Push Pull Power
Amplifier operation, cross over distortion, conversion efficiency, heat sinks.
Unit 4: Feedback: (12P, 15M)
Concept of feedback, types of feedback, Topologies of feedback, Effect of negative feedback on
gain, non linear distortion, Band width, Noise, Input and output impedance, (derivations are not
expected). Emitter follower – operation, characteristics and applications.
Unit 5: Transistorized Oscillator (13P, 15M)
Tank Circuit, Bark Hausen criterion, Oscillator types, Phase Shift Oscillator, Hartley Oscillator,
Colpitts Oscillator, Crystal Oscillator, (working, advantages & disadvantages), RF oscillator.
Reference:
1. Principles of Electronics - V. K. Mehta
2. Electronic Principles - A. P. Malvino
3. Basic Electronics & Linear Circuits - N. N. Bhargava
4. Integrated Electronics- Millman Halkias
 North Maharashtra University, Jalgaon
S.Y.B.Sc. Electronics
Paper II (Semester - I)
ELE 232: Instrumentation
Unit 1: Analog and Digital Meters (15P, 18M)
PMMC- construction and working, DC ammeter (Construction and Design), Ayrton
multirange ammeter and numeric problems.
DC Voltmeter (Construction and Design), multirange voltmeter, sensitivity, loading
effect and numerical problems
Ohm-meter series type and its calibration
Idea of analog multimeter, DMM-Block diagram, working, I to V and R to V conversions
Unit 2: Basic test Instruments (14P, 15M)
a)Power Supply- Unregulated and regulated power supplies, Series Voltage regulator, Fixed
3 terminal voltage regulator, Load and Line regulation, Introduction to SMPS
b)Signal Generator- Block diagram and working of standard signal generator, application in
laboratory.
c)CRO- Block diagram of general purpose CRO and function of each block. Applications –
Voltage and frequency measurement
Unit 3: Transducers (14P, 12M)
Classification of Transducer – Active and Passive.
Electomechanical Transducer- Resistance pressure transducer
Thermoelectric Transducer- Thermocouple, RTD
Photoelectric Transducer: Photo-emissive –Photo Multiplier tube, Photoconductive –LDR,
Photovoltaic- Solar Cell, Opto-coupler
Electro-acoustic Transducer –Condenser, Microphone, P.M Loudspeaker
Unit 4: Data converters (10P, 09M)
Need of data converters, DAC-Binary weighted and Binary ladder
ADC-Counter type Dual slope integration type, Idea of DVM.
Unit 5: DFM (07P, 06M)
Working Principle, block diagram and working, Time –base generator, Frequency
measurement and Period measurement
Reference Books:
1. Electronics Instrumentation –H.S.Kalsi(TMH)
2. Electronics Instrument& Measurement Techniques-W. D.Cooper
3. Instrumentation Devices & Systems- Rangan, Mani, Sharma, TMH
4. A course in electrical and electronic measurements and instrumentation- Sawhney A.K.,
Dhanpat Rai & Company.
5. Electronic Instrumentation – R.V. Jalgao
6. Transducers and Display System – B. S. Sonde
 NORTH MAHARASHTRA UNIVERSITY, JALGAON.
S. Y. B. Sc. Electronics.
Paper – III ELE-203- Practical
ELE – 233 PRACTICAL COURSE - I
Group A (Any four)
1. Design, Build and test Single stage Common Emitter Amplifier.
2. Build and test RC-coupled transistor Amplifier.
3. Study of Directional Characteristics of Microphone.
4. Build and test Class B Push Pull Amplifier.
5. Build and test Emitter follower using Transistor.
6. Build and test Phase Shift oscillator for given frequency using Transistor.
7. Build and test Crystal Oscillator using Transistor.
Group B (Any four)
1. Design of DC ammeter.
2. Design of DC Voltmeter.
3. Regulated Power Supply using 78XX.
4. Design of Temperature to Frequency Convertors using OP-Amp/timer and Thermistor.
5. Optocopler using LED and LDR
6. DAC using R-2R Network
7. Study of Characteristics of photovoltaic Solar Cell .
ELE – 243 PRACTICAL COURSE - II
Group C (Any four)
1. Study of parameter of OP-amp (offset Null and output Impedance).
2. Build and test adder and subtractor using OP-Amp.
3. Design, Built and test V-I Convertor using OP-Amp (Grounded Load).
4. Design, Built and test Low Pass Active Filter using OP-Amp.
5. Design, Built and test Square and triangular Wave generator.
6. Study of Log Amplifier using diode and Op-Amp.
7. Design, Built and test Astable Multivibrator using IC 555.
Group D (Any four)
1. Write an Assembly Language Program to add and subtract two hexadecimal numbers
2. Write an Assembly Language Program to multiply 8-bit unsigned number by 8-bit
unsigned number.
3. Write Assembly Language Program to divide 16-bit unsigned number by 8-bit unsigned.
4. Write an Assembly Language program to convert the hex number into an ASCII
character.
5. Write a program in Assembly Language to find smallest and smallest number from a
series of number.
6. Write an Assembly Language program to convert BCD number into hexadecimal
number.
7. Write a program to calculate the sum series of number.
 North Maharashtra University, Jalgaon
S.Y.B.Sc. Electronics
Paper I (Semester - II)
ELE 241: LINEAR INTEGRATED CIRCUITS & APPLICATIONS
Unit 1: Differential Amplifier: (06P, 10M)
Introduction, CMRR, differential amplifier configurations (mention types with circuit
diagram only), Emitter coupled differential amplifier, differential amplifier with constant
current source.
Unit 2: Operational Amplifier - (14P, 12M)
Block diagram, Schematic symbol, Pin diagram (IC 741), Parameters: - Input impedance,
output impedance, input offset voltage, open loop voltage gain, input bias current, slew rate.
(Definitions only) Concept of offset Null arrangements Ideal characteristics of an Op-Amp,
practical characteristics of an Op-Amp, inverting amplifier, concept of virtual ground,
noninverting amplifier, voltage follower.
Unit 3: General applications of Op-Amp - (12P, 10M)
Op- Amp as Adder, Subtractor, Differentiator, integrator, Instrumentation amplifier with
three Op-Amps, voltage to current converter with floating load and grounded load, Log
amplifier using diode.
Unit 4: Active filters and Comparators - (14P, 13M)
Classification of filter, Active filters – Advantages, limitations and types, first order low pass
and high pass active filters (Derivation of gain and designing), Basic comparator, Schmitt
trigger, comparator characteristics, Sample and Hold Circuit, Basic peak detector, precision
half wave and full wave rectifier.
Unit 5: Waveform generators (14P, 15M)
Timer IC-555 and its application - Pin diagram, Functional block diagram, Concept of
multivibrator, Astable Multivibrator – Operation and its applications (Square wave generator,
Free running ramp generator), Monostable Multivibrator – Operation and its applications
(frequency divider, pulse stretcher), Bistable Multivibrator– Operation, Voltage controlled
Oscillator (VCO).
Reference Book –
1. Operational Amplifier - G. B. Clayton
2. Operational Amplifier and Linear Integrated Circuits - R. A. Gaikwad
3. Integrated Circuits - K. R. Botkar
 North Maharashtra University, Jalgaon
S.Y.B.Sc. Electronics
Paper II (Semester - II)
ELE 242: 8085 Microprocessor
Unit 1: Fundamentals of Microcomputer. (06P, 09 M)
Simple Microcomputer Architecture, Microcomputer operation, Address bus, Data bus,
control bus, High level language, Low level language, Assembler, Compiler.
Unit 2: Architecture of 8085 Microprocessor. (10P, 09 M)
The 8085 pin diagram and function of each pin, Microprocessor Communication and Bus
Timings, De-multiplexing the Bus AD7-AD0, Microprocessor Architecture and Function of
each block.
Unit 3: Instruction set of 8085 Microprocessor. (18P, 18M)
Study of addressing mode for 8085:-Implied Addressing, Register Addressing, Immediate
Addressing, Direct Addressing, Register Indirect Addressing , Instruction set:- Data transfer
Instructions, Arithmetic Instructions, Logical Instructions, Branching Instructions, Stack, I/O
and Machine Control Instructions.
Unit 4: Assembly Language Programming. (16P, 15M)
Assembly Language Format, Assembler Directives (ORG, EQU, DB, DW, DS, END)
Arithmetic Programs: - 8-bit addition, 8-bit subtraction, Decimal addition and subtraction
of two 8-bit numbers, 8-multiplication, one’s and two’s complement of 16-bit numbers, find
largest and smallest Number from a series of given number. Code Conversion Programs:-
Hex to ASCII conversion , BCD to binary conversion.
Unit 5: The 8255A Programmable Peripheral Interface. (10P, 09M)
Block diagram of the 8255A, Control word format, Input/ Output mode, BSR (Bit Set/Reset)
Mode.
References:
1. Fundamentals of Microprocessors and Microcomputers – Badri Ram, Dhanpat Rai and
Sons, Delhi.
2. 8085 Assembly Language Programming – L. A. Leaventhal.
3. Microprocessor Architecture Programming and Applications 8080 & 8085 – Ramesh
Gaonkar.
4. Advance Microprocessor and peripherals (Architecture, Programming and interfacing) –
A. K. Ray, K. M. Bhurchandi.