Asymmetric Ground Structured Circularly Polarized Antenna For ISM and WLAN Band Applications

Download as pdf or txt
Download as pdf or txt
You are on page 1of 9

Progress In Electromagnetics Research M, Vol.

76, 167–175, 2018

Asymmetric Ground Structured Circularly Polarized Antenna


for ISM and WLAN Band Applications

Badugu P. Nadh, Boddapati T. P. Madhav* , Munuswamy S. Kumar,


Manikonda V. Rao, and Tirunagari Anilkumar

Abstract—This article presents the design and analysis of a dual-band antenna with circular
polarization for ISM and WLAN band applications. The proposed antenna operates at two frequencies
ranging from 2.1–3.1 GHz and 4.4–7.7 GHz with resonating frequencies at 2.45 GHz industrial, scientific
and medical band (ISM) and 5.8 GHz wireless local area network band (WLAN). The antenna is fed by
coplanar waveguide feeding (CPW) with an asymmetric ground structure, and the radiating element
consists of 24 spokes in the design. The current antenna providing the impedance bandwidths of 38.4%
and 49% at two operating bands. The proposed antenna exhibiting circular polarisation with 3 dB axial
ratio bandwidth of 150 MHz at 2.33–2.48 GHz and 1600 MHz at 5.14–6.74 GHz. The designed antenna
is fabricated on an RT Duroid 5880 substrate with dimensions of 40 × 28 × 0.4 mm3 . The intension
behind the design of this antenna is to use it for wearable applications in conformal nature with low
specific absorption rate (SAR). The SAR values observed at two operating frequencies are 1.09 W/Kg
and 1.47 W/Kg on hand and 0.946 W/Kg and 1.12 W/Kg on head, respectively. The placement and
radiation characteristics analysis is done with Ansys Savant tool, and the subsequent measured results
provide good correlation with simulation results.

1. INTRODUCTION

ISM band based wearable antennas are getting their significance in medical industry to improve the
quality of communication service [1]. These antennas are used in many applications like telemedicine,
military, sports and in emerging new technologies [2]. To cover these applications, designed antennas
need to cover WBAN frequencies like 2.4 GHz (2.4–2.485) GHz and 5.8 GHz (5.725–5.875) GHz [3].
Owing to significant demand for these frequency bands, several efforts have been made to design dual-
band antennas with compact size, flexibility and good operating characteristics [4]. To place the antenna
on human body there are some limitations to be considered such as size, safety and low propagation
losses inside the conductive layers [5]. The antenna is placed on high dielectric constant layers like
skin which leads to frequency disturbance and back radiation influence by the human layers and causes
biological effects.
In the literature, various antennas have been designed to achieve good on-body communication [6].
A monopole antenna is designed with inverted L-shape for ISM applications covering (2.42–2.48 GHz)
and (5–6 GHz) [7]. The multiband antenna is designed to cover three ISM bands at 2.4–2.48 GHz, 5.15–
5.35 GHz and 5.7–5.8 GHz [8]. A dual-band monopole patch antenna is designed with CPW feeding
for on/off-body communication operating at medical (ISM) bands covering 2.45 GHz and 5.8 GHz
respectively. A fan-shaped antenna is designed with shorting stubs and crumpling nature in [9]. A
shorted patch antenna of parasitic elements with omnidirectional patterns at 2.45 GHz and 5.8 GHz
Received 14 September 2018, Accepted 21 November 2018, Scheduled 11 December 2018
* Corresponding author: Boddapati T. P. Madhav ([email protected]).
The authors are with the Antennas and Liquid Crystals Research Center, Department of Electronics and Communication Engineering,
Koneru Lakshmaiah Education Foundation, AP, India.
168 Nadh et al.

is presented in [10]. A circular monopole patch antenna with four symmetric slots is designed for
omnidirectional radiation pattern and operating in ISM band. A circularly polarised antenna with
asymmetric crossed bowtie dipoles is designed to cover medical band frequencies with axial ratio
bandwidths of 57% and 51% [11]. A circularly polarised antenna is designed with a Taconic RF-35
substrate which covers the GPS, WiMAX, WLAN, and radio altimeter applications [12]. A foldable thin
circular monopole antenna is designed with liquid crystalline polymer substrate for wearable applications
with different bending conditions [13]. A tai-chi-shaped antenna is designed with circular polarisation
for dual-band applications in [14]. A conformal antenna is designed on a paper substrate with graphene
as a radiating element instead of copper in [15]. Shin et al. [17] proposed a meander line monopole
antenna for PCS/IMT-2000/WLAN handsets with reduction in the SAR value. Ahmed et al. [18]
presented an eagle-shaped wearable MIMO antenna with reduction of mutual coupling to 36 dB by
placing EBG structure between antenna elements.
In this article, a circular ring-shaped antenna with 24 spokes is designed to attain dual-band
frequency. The designed antenna is fed by CPW feeding, and a novel asymmetric ground structure is
taken in this model. Dual operating bands for ISM and WLAN applications are aimed in this article
with circular polarisation. To test the antenna for wearable applications, different bending effects at
different bending angles are analyzed and presented in this work. A novel compact structured antenna of
dual-band operation at medical communication bands with circular polarization is an attractive feature
of this model. The designed model provides excellent impedance characteristics and peak realized gain
of 4.6 dBic.

2. ANTENNA DESIGN AND DIMENSIONS

The topology of the antenna is presented in Fig. 1. The prototyped antenna is designed on a semi-
flexible substrate of Rogers Duroid 5880 material with dielectric constant of 2.2 and loss tangent of
0.007. The overall dimension of the antenna is 40 × 28 × 0.4 mm3 . The constructed antenna consists
of a circular ring with CPW feeding as shown in iteration 1. In iteration 2, 8 spokes are added to the
circular ring and are separated by an angle of 45◦ each, with each spoke connected to the ring. In
iterations 3, eight spokes are replaced with 16 spokes, which are separated by an angle of 22.5◦ . In the
proposed model, 16 spokes are replaced with 24 spokes, and each spoke is separated by an angle of 15◦ .
In between the spokes, a circle with radius of 0.6 mm is taken to separate the spokes on the circular
ring. At the center of radiating patch, a circular slot is made with radius of 1 mm. In the ground

(a) (b) (c) (d)

Figure 1. (a) Circular antenna. (b) Ring antenna with 8 spokes. (c) Ring antenna with 16 spokes.
(d) Proposed antenna dimensions with 24 spokes.

Table 1. Parameters of circular ring antenna.

Parameter Ls Ws Lf Wf W1 L1 L2 Sl R1 R2 R3 θ d
Value (mm) 40 28 16 3 12 13 10 5.5 12 9.5 3.5 15 2.5
Progress In Electromagnetics Research M, Vol. 76, 2018 169

plane, an asymmetric structure is taken with lengths of ‘L1 ’ and ‘L2 ’ to attain circular polarisation.
Table 1 presents dimensions of the proposed antenna in mm. The circular ring structure is derived from
a circular patch whose radius ‘R1 ’ is calculated using the given formula [13].
F
R1 =     1/2 (1)
2h πF
1+ ln + 1.7726
πεr 2h

3. RESULTS AND DISCUSSIONS

The basic circular ring antenna producing resonating frequency at 2.1 GHz with frequency ranging
from 1.8 to 2.7 GHz, which covers GSM-1.8/1.9 GHz, Digital communication band (1.8 GHz), UMTS
(1.9 GHz) and Industrial scentific medical bands (2.45 GHz) and lower band WLAN applications. When
eight spokes and sixteen spokes are added to the circular ring structure, the antenna resonates at
2.45 GHz ranging from 2 to 2.8 GHz.
When 24 spokes are loaded to the antenna structure, it operates in the dual bands at resonating
frequencies of 2.45 GHz and 5.8 GHz, respectively. The first frequency band ranging from 2.1 to 3.1 GHz
with bandwidth of 1 GHz covering ISM band and second band ranging from 4.4 to 7.3 GHz with
bandwidth 2.9 GHz covering WLAN applications band. In Fig. 2(b) the peak gain of the antenna
and axial ratio are presented. The antenna shows maximum peak gain of 2.2 dBic at 2.45 GHz and
4.6 dBic at 5.8 GHz. The antenna provides circular polarisation with 3 dB axial ratio of 150 MHz and
1600 MHz at two resonating frequencies.

(a) (b)

Figure 2. Antenna performance characteristics. (a) Reflection coefficients of the antenna iterations.
(b) Peak gain and axial ratio of the proposed antenna.

A parametric study is carried out to analyze critical parameters that will tune the antenna
functionality. The parametric studies of reflection coefficient for different values of R2 , R3 , L1 and
Wf are presented in Fig. 3. In this analysis, one parameter is varied, and all other parameters are kept
constant. The inner circle radius is varied from 8.5 to 10 mm with step size of 0.5 mm and presented
in Fig. 3(a). For the lower values of R2 , the antenna shows single frequency band at 2.45 GHz. When
the value of R2 is varied from 8.5 to 9.5 mm, antenna resonates at dual bands of 2.45 GHz and 5.8 GHz,
respectively. Similarly, when circle radius R3 is varied from 2.5 to 4.5 mm, antenna operates in the dual
bands for R3 = 3.5 mm, and for other values it does not show any resonating frequency at 5.8 GHz.
Similarly the length of the ground (L1 ) is varied from 11 to 14 mm, and as the length of ground
increases, there is a variation in the second resonant band at 5.8 GHz. The designed antenna shows
circular polarization with an asymmetric ground structure. So, the ground structure is studied by
170 Nadh et al.

(a) (b)

(c) (d)

(e) (f)

Figure 3. Parametric analysis of (a) varying the second circle radius. (b) Varying the third circle
radius. (c) Length of ground. (d) Width of the feed. (e) Axial ratio variation for length of the ground
(L1 ). (f) Axial ratio variation for length of the ground (L2 ).

varying parameters L1 and L2. Figs. 6(e) and (f) show the parametric analyses of L1 and L2,
respectively. Parameter L1 is varied from 11 mm to 14 mm, and the observed maximum 3 dB axial
ratio bandwidth is observed at L1 = 13 mm. Similarly, the length of the second ground (L2) is varied
from 8 mm to 11 mm by fixing the L1 value to 13 mm, and the maximum 3 dB axial ratio bandwidth is
observed at L2 = 10 mm. In Fig. 3(d), width of the feed (Wf ) is varied from 2.6 to 3.2 mm, and for feed
Progress In Electromagnetics Research M, Vol. 76, 2018 171

width 2.6 mm the fundamental resonant frequency shifted to 2 GHz and second resonant frequency to
7.7 GHz. For the selected value of Wf = 3 mm, antenna resonates at required frequencies of 2.45 GHz
and 5.8 GHz.
The surface current distribution of the proposed antenna is presented at two different frequencies
of 2.45 GHz and 5.8 GHz in Fig. 4. The representation of current distribution is given at different time
instants of 0◦ , 90◦ , 180◦ and 270◦ , respectively. At 2.45 GHz, the orientation of current elements is in
anticlock wise direction which leads to right-hand circular polarisation (RHCP). Similarly at 5.8 GHz,
the same kind of current distribution is observed. Fig. 5 represents the antenna reflection coefficient and
axial ratio at different bending angles. The antenna performance is evaluated by bending antenna to
30◦ , 60◦ and 90◦ . In the simulation study, as the bending angle increases, the reflection coefficient value
at the second band of 5.8 GHz reaches minimum value, but at the lower frequency band of 2.45 GHz
there is not much variation.

.
0 0 0
0 90 180 2700
(a)

00 900 1800 2700


(b)

Figure 4. Surface current distribution at (a) 2.45 GHz, (b) 5.8 GHz.

(a) (b)

Figure 5. Proposed antenna. (a) Reflection coefficient. (b) Axial ratio.


172 Nadh et al.

4. ON-BODY PLACEMENT ANALYSIS

As the antenna is designed for wearable applications it should be placed on the human body, and its
functionality is analyzed. For doing the on-body analysis, the antenna is placed on the human body like
CAD homogeneous model available in CST is taken. Generally, human body consists of high dielectric
constant layers like skin, fat, muscle and bone which will influence the antenna performance.
In this case, voxel structure is too large, compared to antenna size which is shown in Fig. 6. To do
SAR analysis, a three-dimensional anatomical hand and head phantom model is taken. The simulation
of SAR is performed using finite-difference time domain (FDTD) method of computer simulation
technology microwave studio (CST) [14–16]. The SAR values are evaluated on 1 gm bological tissue.
An input power of 0.5 W was used in the simulation setup. The obtained SAR values of 1.09 w/kg and
0.946 W/Kg at 2.45 GHz and 1.47 w/kg and 1.12 W/Kg at 5.8 GHz can be observed on hand and head
from Fig. 6. The observed values satisfy FCC and ICNRIP standards for which the values should be
less than 1.6 w/kg averaged over 1 gm of tissue and 2 w/kg averaged over 10 gm of tissue.

(a) (b) (c)

(d) (f)

Figure 6. (a) Antenna mounted on wrist and head (b), (d) SAR value at 2.45 GHz (c), (f) SAR value
at 5.8 GHz.

The radiation field analysis is performed in Ansys savant simulation tool, which is based on shooting
and bouncing rays method. The field distributions are calculated at resonating frequencies like 2.45 GHz
and 5.8 GHz, and the far-field radiation patterns are presented using ANSYS Savant simulation tool
in XZ, Y Z, XY -planes as shown in Fig. 7. In XZ-plane and Y Z-plane, the radiation patterns
are dumbbell-shaped in free standing antenna at 2.45 GHz and 5.8 GHz. There is a slight variation
of patterns when antenna is placed on human body. In the elevation planes at 2.45 GHz maximum
distribution is observed at 60◦ –70◦ in Y Z-plane. In the azimuth plane, radiation patterns are nearly
omnidirectional in nature at two frequencies. At 5.8 GHz, the maximum radiation patterns are nearly
directional in which maximum distribution is observed along 60◦ in XZ-plane and 45◦ in Y Z-plane.
Fig. 8 presents simulated and measured reflection coefficients of the antenna. At the first resonating
frequency, the simulation results are exactly matched with measured results, and for the second
resonating frequency band, there is a slight mismatch between simulated and measured values. However,
Progress In Electromagnetics Research M, Vol. 76, 2018 173

XZ-Plane YZ-Plane XY-Plane 3D-Radiation pattern

Figure 7. Simulated far field patterns of proposed antenna at 2.45 GHz and 5.8 GHz.

Table 2. Comparison of proposed antenna with previous works.

Peak SAR
Frequency Impedance
Ref Size Gain Values Applications
Range (GHz) bandwidth (%)
(dBi) (W/Kg)
1.78–1.98 10.92 −30.5 5.77 GSM
[2] 90 × 124 × 1
2.38–2.505 5.08 −22.2 6.62 ISM
2.4–2.485 3.4 2.6 - ISM
[4] 30 × 45 × 3.2
5.725–5.875 2.5 3.6 - BANDS
0.38–0.47 12.4 3.09 5.42 MICS and
[5] 27 × 28 × 0.6
2.27–2.57 16.1 0.64 4.70 ISM
0.4–0.405 1.2 0.49 0.05 MICS and
[6] 40 × 40 × 4.2
2.35–2.57 8.9 2.3 1.13 ISM
1.54–1.62 5 1.41 0.2
2.67–2.87 7.2 3.56 0.607 GPS, WiMax
[14] 70 × 70 × 1.6
3.33–3.46 3.8 1.8 0.603 and WiFi
5.24–5.42 3.7 2.38 0.347
1.75-2.25 25 - 0.6 PCS/IMT-
[15] 60 × 23 × 1.6
2.3–2.6 12 - 1.33 2000/WLAN
2.16-2.75 23 2.275 1.514 WLAN and
[16] 30 × 50 × 1.5
7.14–9.91 33 3.151 1.82 RFID
Proposed 2.1–3.1 38 2.2 1.09
40 × 28 × 0.4 ISM/WLAN
antenna 4.4–7.7 54 4.6 1.47
174 Nadh et al.

(a) (b)

Figure 8. Performance characteristics of the antenna. (a) Reflection coefficient, (b) flexible nature.

Figure 9. Simulated and measured E-plane radiation patterns at 2.45 GHz and 5.8 GHz.

the bandwidth coverages of both frequency bands for simulation and measurement are quite similar.
The measured radiation patterns are compared with simulated ones in Fig. 9.
Table 2 is presented here for the comparison of the current antenna performance characteristics with
previous literature. Compared with previous works, a significant improvement in gain and reduction in
size can be observed. The SAR values also satisfy the FCC standards.

5. CONCLUSION

A dual-band antenna operating for ISM band and WLAN applications is designed in this work. The
antenna is a novel circular ring-shaped antenna with 24 spokes and semi-flexible nature, which is more
suitable for wearable applications. To analyse the performance in real time environment, the antenna is
placed virtually on human body and validates the performance characteristics. The designed antenna
providing a peak gain of 2.2 dBic at 2.45 GHz and 4.6 dBic at 5.8 GHz and providing dipole like radiation
and omnidirectional radiation in E and H-planes, respectively. The observed SAR values of 1.09 W/Kg
and 1.47 W/Kg on hand and 0.946 W/Kg and 1.12 W/Kg at 2.45 GHz and 5.8 GHz, respectively satisfy
the FCC standards. Measured results of the proposed antenna correlate with simulation ones, and the
current model can be implemented in wearable devices for the specified application bands to establish
good communication link.
Progress In Electromagnetics Research M, Vol. 76, 2018 175

REFERENCES

1. Zhu, D., Y.-X. Guo, M. Je, and D.-L. Kwong, “Design and in vitro test of a differentially fed dual-
band implantable antenna operating at MICS and ISM bands,” IEEE Transactions on Antennas
and Propagation, Vol. 62, No. 5, 2430–2439, 2014.
2. Velan, S. and E. F. Sundarsingh, “Dual-band EBG integrated monopole antenna deploying fractal
geometry for wearable applications,” IEEE Antennas and Wireless Propagation Letters, Vol. 14,
249–252, 2015.
3. Tak, J., S. Woo, J. Kwon, and J. Choi, “Dual-band dual-mode patch antenna for on-/off-body
WBAN communications,” IEEE Antennas and Wireless Propagation Letters, Vol. 15, 348–351,
2016.
4. Deepak, U., T. K. Roshna, C. M. Nijas, K. Vasudevan, and P. Mohanan, “A dual band SIR
coupled dipole antenna for 2.4/5.2/5.8 GHz applications,” IEEE Transactions on Antennas and
Propagation, Vol. 63, No. 4, 1514–1520, 2015.
5. Xu, L.-J., Z. Duan, and Y.-M. Tang, “A dual-band on-body repeater antenna for body sensor
network,” IEEE Antennas and Wireless Propagation Letters, Vol. 15, 1649–1652, 2016.
6. Kang, D.-G., J. Tak, and J. Choi, “Dual-band on-body antenna for in-on-on WBAN repeater
applications,” Microwave and Optical Technology Letters, Vol. 58, No. 2, 436–441, 2016.
7. Lu, L. and J. C. Coetzee, “A modified dual-band microstrip monopole antenna,” Microwave and
Optical Technology Letters, Vol. 48, No. 7, 1401–1403, 2006.
8. Yeung, S. H., K. F. Man, and W. S. Chan, “Optimised design of an ISM band antenna using a
jumping genes methodology,” IET Microwaves, Antennas & Propagation, Vol. 2, No. 3, 259–267,
2008.
9. Tak, J., D.-G. Kang, and J. Choi, “A compact dual-band monopolar patch antenna using TM01
and TM41 modes,” Microwave and Optical Technology Letters, Vol. 58, No. 7, 1699–1703, 2016.
10. Zhu, X.-Q., Y.-X. Guo, and W. Wu, “A novel dual-band antenna for wireless communication
applications,” IEEE Antennas and Wireless Propagation Letters, Vol. 15, 516–519, 2016.
11. Tran, H. H. and I. Park, “Wideband circularly polarized cavity-backed asymmetric crossed bowtie
dipole antenna,” IEEE Antennas and Wireless Propagation Letters, Vol. 15, 358–361, 2016.
12. Tu, T. L., H. H. Tran, and H. C. Park, “A simple penta-band circularly polarized cpw-fed monopole-
patch antenna covering six commercial application bands,” Microwave and Optical Technology
Letters, Vol. 60, No. 3, 773–778, 2018.
13. Zahran, S. R., M. A. Abdalla, and A. Gaafar, “Time domain analysis for foldable thin UWB
monopole antenna,” AEU-International Journal of Electronics and Communications, Vol. 83, 253–
262, 2018.
14. Saygin, H., V. Rafiei, and S. Karamzadeh, “A new compact dual band CP antenna design,”
Microwave and Optical Technology Letters, Vol. 60, No. 3, 594–600, 2018.
15. Sajal, S., B. D. Braaten, T. Tolstedt, S. Asif, and M. J. Schroeder, “Design of a conformal monopole
antenna on a paper substrate using the properties of graphene-based conductors,” Microwave and
Optical Technology Letters, Vol. 59, No. 6, 1279–1283, 2017.
16. Ahmed, M. I., M. F. Ahmed, and A. E. H. Shaalan, “SAR calculations of novel wearable fractal
antenna on metamaterial cell for search and rescue applications,” Progress In Electromagnetics
Research, Vol. 53, 99–110, 2017.
17. Shin, C. S., D. G. Choi, N. Kim, and J. I. Choi, “Internal monopole antenna design for multi-band
operation and SAR analysis,” PIERS Proceedings, 294–297, Hangzhou, Zhejiang, China, Aug. 22–
26, 2005.
18. Ahmed, M. I., E. A. Abdallah, and H. M. Elhennawy, “Novel wearable eagle shape microstrip
antenna array with mutual coupling reduction,” Progress In Electromagnetics Research B, Vol. 62,
87–103, 2015.

You might also like