0% found this document useful (0 votes)
105 views4 pages

An Open Electronic Marshalling Solution

1) Siemens recently introduced the first open industrial network-based electronic marshalling solution called the SIMATIC Compact Field Unit (CFU) and SIMATIC ET 200SP HA products. 2) These products use standard redundant PROFINET for communications, enabling integration with other PROFINET devices from different manufacturers. 3) Version 9.0 of the Simatic PCS 7 DCS incorporates electronic marshalling and supports "late binding" concepts, allowing parallel development and testing of hardware.

Uploaded by

manuelsantos2007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
105 views4 pages

An Open Electronic Marshalling Solution

1) Siemens recently introduced the first open industrial network-based electronic marshalling solution called the SIMATIC Compact Field Unit (CFU) and SIMATIC ET 200SP HA products. 2) These products use standard redundant PROFINET for communications, enabling integration with other PROFINET devices from different manufacturers. 3) Version 9.0 of the Simatic PCS 7 DCS incorporates electronic marshalling and supports "late binding" concepts, allowing parallel development and testing of hardware.

Uploaded by

manuelsantos2007
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

An Open Electronic Marshalling Solution? Finally!

- Siemens Delivers
September 19 - 2017

By Bill Lydon, Editor, Automation.com

For years we have extensively covered and supported the push for open network
automation solutions, and once again we are seeing some incredible innovation
as a result. Most recently, Siemens introduced the first open industrial network-
based electronic marshalling solution, during the 2017 Siemens Automation
Summit in June in Boca Raton, Florida. I was able to get a firsthand look at the
SIMATIC Compact Field Unit (CFU) and SIMATIC ET 200SP HA products during
the event and learned more about them from Stacey Jarlsberg, a Product
Manager for Siemens Industry. Given the number of vendors that have
introduced electronic marshalling products, the value of electronic marshalling is
clear. With Siemens’ entry into the world of open automation solutions, the value
of these solutions should become increasingly clear as well.

Opening Communications with Open Protocol


Most exciting about this new offering is that it’s the first electronic marshalling
product that uses a recognized open architecture industrial ethernet protocol for
communications. All the other DCS solutions available use closed protocols.
Jarlsberg explained that since the Siemens solution uses standard redundant
PROFINET, this enables other PROFINET devices to be easily used. Let’s take a
look at how this is accomplished with the new offerings:

SIMATIC Compact Field Unit (CFU)


The SIMATIC Compact Field Unit (CFU) communicates using standard
redundant PROFINET connection for the highest availability and can be
configured for electrical, optical, or mixed physical network-based on
requirements. The CFU supports full redundancy, including redundant
PROFINET connectivity and power supplies.

SIMATIC CFU Leverages Open Industrial Protocol – PROFINET and


PROFIBUS PA
The Compact Field Unit (CFU) supports direct PROFIBUS PA integration and
support of advanced PROFIBUS PA Features. The CFU can support both
PROFIBUS PA digital fieldbus devices and conventional digital signals in the
same I/O. Each 16-channel standard CFU I/O module can support up to 8
channels of PROFIBUS PA. The CFU also includes several enhancements for
PROFIBUS PA integration and functionality, such as automatic detection and
integration of devices. An auto-detect/auto-integrate feature is done using
standard PROFIBUS PA device profiles. These provide the system with all the
basic device information as well as the process value (PV).

SIMATIC ET 200SP HA
The SIMATIC ET 200SP HA is modularly designed in such a way as to use
minimum space in control panels. It features a tool-free connection using push-in
terminals and fixed wiring in order to cut the costs of engineering, assembly and
wiring. Its temperature range (from -40°C to +70°C) and Conformal Coating
makes the SIMATIC ET 200SP HA ideally suited for field use. The desired
advantages of this new technology include a Change in Run thanks to a
redundant layout, and a greater number of modules on the head station,
increased from 12 to 56. The 200SP features redundant PROFINET, hot
swapping modules - up to a maximum of 56 I/O modules per station - high
channel density of up to 32 channels on a module, integrated power bus,
seamless integration in SIMATIC PCS 7. The modules currently available
include: 16×AI / 8×AO, HART, 16×DI, and 16×DO.

Version 9.0 of the Simatic PCS 7 DCS


Any new devices need technical support, and that support for these devices is
part of Version 9.0 of the Simatic PCS 7 DCS. This version incorporates
Electronic Marshalling, along with I/O on demand, in order to simplify
engineering, installation, and commissioning of systems. Version 9.0 separates
I/O hardware from software to support the “late binding” concepts, recently
outlined as part of ExxonMobil’s “It Just Happens” initiative by Sandy
Vasser. The DCS itself can be developed in a virtual environment and paired
with the system hardware at the last possible moment, allowing for parallel
development of the system and installation and testing of the associated
hardware. Version 9.0 also provides tools that simplify field device
commissioning, including direct integration with PROFIBUS PA and a whole new
set of PROFIBUS PA features.
Supporting Standard GSD
The software supports standard GSD (General Station Description) files which
contain a description of the PROFIBUS DP/PA or PROFINET devices, as
opposed to other offerings which have closed, propriety architectures. GSD files
provide a way for an open configuration to automatically get the device
characteristics from any manufacturer that support PROFIBUS DP/PA or
PROFINET open standards. This benefits the entire industry, as open device
profiles can significantly reduce the time needed to commission field devices.
Further it can also allow for auto configuration of devices in parallel with process
automation system engineering, before the actual process automation system is
fully installed. This PROFINET support at the control network - rather than a
proprietary control network protocol that utilizes an Ethernet physical layer -
allows the integration of a wide range of PROFINET-compliant products and
components from multiple suppliers including include remote I/O, drives, network
components, and other devices.
The Siemens solution is designed to reduce cost, complexity, and customization
typically associated with conventional process I/O. The single-channel I/O is
assigned its type through software configuration, independent of any hardware or
wiring.

Saving Time with Automatic Addressing


In another time-saving effort for the new technology, the Ethernet-based field
distributor starts an initialization process in which devices are automatically
addressed. The Simatic CFU automatically carries out the addressing procedure
and the integration based on standard profiles, depending on the type of device
used (pressure or temperature transmitter, magnetic flowmeter, etc.). These
communication and device profiles are standard features of PROFIBUS PA, and
thus supported by a wide range of field device suppliers. The device is then
integrated in the control system and ready to operate. Siemens refers to this
process as “plug-and-produce,” terminology similar to that used in process
modularization approaches.
Siemens estimates that this will take significant time out of installation and can
make it easier to commission digital fieldbus devices than it would be to replace
conventional analog devices. Siemens believes that the device installation time
can drop, from 30 minutes or more for conventional devices, down to as low as
one minute for PROFIBUS PA devices.

Bill’s Thoughts & Observations


Having followed the progression of available open solutions, I believe that
Siemens electronic marshaling offering is headed in the right direction and
represents a leap forward for the open effort. By tradition, DCS system
architecture, segregation of functions and labor apparently required marshaling
cabinets. This never made a whole lot of sense to me. In my own building
automation and factory automation experience - from an engineering and
applications point of view - I never felt marshaling cabinets served a great deal of
purpose. PLC systems, for years, have used remote I/O using simple
interchangeable slice point modules. The introduction of electronic marshaling,
by DCS companies, has always made sense but it was always bothersome to me
that they were all based on closed proprietary networking protocols.
Siemens’ initial efforts in electronic marshaling, based on industry standard open
architecture protocols, is a refreshing step towards the open systems desired by
so many of today’s automation users.

You might also like