Stress Strain Diagram

Stress-Strain Diagrams
Stress-Strain Curves for Ductile Materials

If a ductile bar of uniform cross-sectional area is subjected to gradually increasing
axial tensile force (generally is done in Universal Testing Machine) till failure of the
bar occurs, when the stress-strain curve plots the curve may be divided into following
parts:
Stress-Strain curve in ductile materials
Portion OA: This portion is absolutely straight, where the stress is proportional to
strain and the material obeys Hooke’s law (σ =E ϵ). The value of stress at point A is
called proportional limit.
Portion AB: In this portion, Hook’s law is not obeyed, although the material may still
be elastic. The point B indicates the elastic limit.
Portion BC: In this portion, the metal shows a strain even without increase in stress
and the strain is not fully return when load is removed.
Portion CD: Yielding start in this portion and there is a drop of stress at the point D
directly after yielding begins at C. The point D is termed as lower yield point and C is
called upper yield point.
Portion DE: After yielding has taken place at D, further straining takes place at this
portion by increasing the stress and the stress–strain curve continues to rise up to the
point E. Strain in this portion is about 100 times that of portion O-A. At the point E,
the bar begins to form a local neck. The point E is termed as ultimate tensile stress
point.
Portion EF: In this portion, the load is falling off from the maximum and fracture at
F takes place. The point F is termed as fracture or breaking point and the identical
stress is called breaking stress.
2-Stress Strain Curves for Brittle Materials
Materials which show very small elongation before they fracture are called brittle
materials. The shape of curve for high carbon steel, concrete and high strength light
alloys or any brittle materials is shown in fig. 3. For most brittle materials the
permanent elongation (i.e. increase in length) is less than 10%.
Principal mechanical properties

The characteristics of the materials which describe their behaviour under external
loads are known as Mechanical Properties.
Some mechanical properties are:
1 -Elasticity
Elasticity of a material is power of coming back to original position when the stress
or load is removed. The greatest stress that a material can withstand without
permanent distortion is called elastic limit.
2- Plasticity
The plasticity of a material is ability to undergo some permanent deformation
without failure. Plastic deformation will take place only after the elastic range has
been exceeded, beyond (point c). Plasticity is an important property and widely used
in several mechanical processes like forming, shaping, extruding and many other hot
and cold working processes. In general, plasticity increases with increasing
temperature.
Due to this property various metals can be transformed into different products of
required shape and size. This conversion into desired shape and size is effected either
by the application of pressure or heat or both.
3- Ductility
Ductility of a material their enables to draw out into thin wire with application the
load. Ductile material such as mild steel, wires of gold, silver, copper, aluminium, etc.
are drawn by extrusion or by pulling through a hole in a die due to the ductile
property. The ductility decreases with increase of temperature. The percent elongation
and the reduction in area in tension are often used as empirical measures of ductility.
4-Strength
It is the resistance offered by a material when subjected to external loading, so
stronger the material can be withstand with greater the load. Depending upon the type
of load applied the strength can be tensile, compressive, shear or torsional strength.
The maximum stress that any material will withstand before destruction is called its
ultimate strength (point E as shown in Fig. 1).
5- Brittleness
The brittleness of a material is the property of breaking without much permanent
distortion. There are many materials, which break or fail before much deformation
take place, such as glass, cast iron, etc. Therefore, a non-ductile material is said to be
a brittle material. A brittle material should not be considered as lacking in strength, it
is only shows the lack of elasticity. On stress-strain diagram, these materials don’t
have yield point and value of E is small.
6- Toughness
The toughness of a material is ability to withstand both plastic and elastic
deformations. It is a highly desirable quality for structural and machine parts to
withstand to shock and vibration. Manganese steel, mild steels are tough materials.
For Ex: If a load is suddenly applied to a piece of mild steel and then to a piece of
glass the mild steel will absorb much more energy before failure occurs. Thus, mild
steel is said to be much tougher than a glass.
7- Hardness
Hardness is closely related to strength. It is the ability of a material to resist
scratching, abrasion, penetration with apply external load.
8- Stiffness (Rigidity)
The resistance of a material to deflection is called stiffness or rigidity. Steel is stiffer
or more rigid than aluminium. Stiffness is measured by Young’s modulus E. The
higher value of the Young’s modulus this mean stiffer the material. E is the ratio of
stress over strain and is given by the slope of line O–A.
materials behaviour in stress strain curve

Stress Strain Diagram

Uploaded by

Copyright:

Available Formats

Stress Strain Diagram

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Stress Strain Diagram

Uploaded by

Copyright:

Available Formats

Stress-Strain Diagrams

Stress-Strain Curves for Ductile Materials

Stress-Strain curve in ductile materials

Principal mechanical properties

You might also like