Manual For CPWD

SUB HEAD : 5.
REINFORCED CEMENT
CONCRETE
90
BASIC RATES (SH: 5.0 REINFORCED CEMENT CONCRETE)
Code Description Unit Rate
No.
0002 Hire charges of Concrete Mixer 0.25 to 0.40 cum with Hopper day 800.00
0004 Production cost of concrete by batch mix plant cum 350.00
0009 Pumping charges of concrete including Hire charges of pump,
piping work & accessories etc. cum 210.00
0011 Hire charges of Pump set of capacity 4000 litres/hour day 700.00
0012 Vibrator (Needle type 40 mm) day 370.00
0025 Hire and running charges of light crane day 3000.00
0026 Hire and running charges of bentonite pump day 3500.00
0029 Carriage of concrete by transit mixer km/cum 30.00
0052 Front end loader 1 cum bucket capacity (incl POL) hour 900.00
0066 Batching and Mixing Plant @ 75 cum per hour hour 2400.00
0070 Generator 100 KVA/125 KVA hour 250.00
0082 Excavation of Diaphragm wall by Mechanical Grab sqm 1300.00
0101 Bhisti day 617.00
0102 Blacksmith 1st class day 738.00
0103 Blacksmith 2nd class day 679.00
0112 Carpenter 2nd class day 679.00
0114 Beldar day 558.00
0115 Coolie day 558.00
0116 Fitter (grade 1) day 738.00
0123 Mason (brick layer) 1st class day 738.00
0124 Mason (brick layer) 2nd class day 679.00
0126 Mason (for ornamental stone work) 1st class day 738.00
0128 Mate day 617.00
0131 Painter day 679.00
0155 Mason (average) day 709.00
0236 Multi purpose fibre (high impact poly propelene reinforced)
cement board 6 mm thick sqm 210.00
0242 6mm thick multipurpose cement bonded wood particle board
conforming to IS : 14276 sqm 195.00
0293 Stone Aggregate (Single size) : 40 mm nominal size cum 1300.00
0302 Safeda ballies 125 mm diameter metre 40.00
0309 Paving bitumen of grade VG-10 of approved quality tonne 25614.00
0313 Blown type petroleum bitumen of penetration 85/25 of approved
quality tonne 34000.00
0314 Bitumen hot sealing compound : grade A kg 28.00
SUB HEAD -5.0 REINFORCED CEMENT CONCRETE 91

No.
0316 Bitumen solution primer of approved quality litre 45.00
0339 Flame retardant face insulating, Impregnated fibre board 12 mm
thick sqm 375.00
0349 Curing compound litre 38.00
0367 Portland Cement (OPC-43 Grade) tonne 4940.00
0370 Coal (steam) quintal 440.00
0596 Bright finished or black enameled mild steel butt hinges 75x47x
1.70 mm 10 Nos 56.00
0639 Bright finished or black enameled mild steel screws 25 mm 100 Nos 36.00
0768 Cement Concrete Jali 50 mm thick sqm 400.00
0967 Copper plate kg 527.00
0982 Coarse sand (zone III) cum 1350.00
0983 Fine sand (zone IV) cum 900.00
0992 Galvanised steel plain sheets quintal 5000.00
1004 Average rate of Mild steel round bars for reinforcement quintal 4500.00
1005 Twisted steel/ deformed TMT bars Fe-500D quintal 4600.00
1015 Mild steel expanded metal 20x60 mm strands 3.25 mm wide
1.60 mm thick sqm 280.00
1021 Hard drawn steel wire fabric 75 x 25 mm mesh of weight not
less than 7.75 kg/sqm sqm 430.00
1034 Bolts and nuts up to 300 mm in length quintal 4800.00
1197 Second class kail wood in scantling 10 cudm 260.00
1198 Second class kail wood in planks 10 cudm 260.00
1215 Welding by electric plant cm 2.00
1224 Hard drawn steel wire quintal 4800.00
1225 Mild steel flat strap fitting quintal 4120.00
1980 Fly ash cum 10.00
2200 Carriage of Steam coal tonne 120.00
2202 Carriage of Stone aggregate below 40 mm nominal size cum 103.77
2203 Carriage of Coarse sand cum 103.77
2204 Carriage of Timber cum 118.59
2205 Carriage of Steel tonne 92.24
2206 Carriage of Stone aggregate 40 mm nominal size and above cum 112.79
2209 Carriage of Cement tonne 92.24
2211 Carriage of Tar / Bitumen tonne 103.77
2261 Carriage of Fine sand (1 Part badarpur sand : 2 Parts Jamuna sand) cum 103.77
2262 Carriage of Flyash cum 103.77
SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 92

No.
2273 Carriage of A.C.sheet and accessories tonne 92.24

2302 Carriage of G.I. sheet and accessories tonne 92.24
2391 Strips-Aluminium fluted 3.15 mm thick and 150 mm wide metre 278.00
2392 Strips Aluminium fluted 3.15 mm thick and 200 mm wide metre 370.00
2393 1 mm thick Stainless Steel Cover plate grade 304 kg 275.00
2394 Coupler 16 mm dia each 30.00
2399 Complete Roof Joint of 100 mm metre 2800.00
2402 Epoxy adhesive kg 150.00
2403 Floor Joint of 100 mm metre 3100.00
2409 Wall Joint of 100 mm metre 2400.00
2447 Hollock ballies 125 mm diameter metre 35.00
7183 Bentonite of 35 kg per pile tonne 2960.00
7318 Plasticizer / super plasticizer kg 36.00
7319 Wall form panel 1250x500 mm each 860.00
7320 Tie bolt 12 mm dia 100 mm length each 38.00
7324 Spring coil 12 mm each 15.00
7325 Plastic cone 12 mm dia each 17.00
7326 Corner angle 45x45x5 mm 1.50 m long each 240.00
7327 100 mm channel shoulder 2.5 m long each 910.00
7328 Double clip (bridge clip) each 76.00

No.
7329 Single clip each 59.00

7330 M.S. tube 40 mm dia metre 215.00
7331 Wall form panel 1250x450 mm each 860.00
7332 Corner angle 45x45x5 mm 2.50 m long each 255.00
7333 Column clamp 450x1070 mm each 965.00
7334 Prop 2 m ( 2-3.5 m) each 635.00
7342 Adjustable span ESO+SI (2.35-3.40) each 1480.00
7343 Adjustable telescopic prop 3 m (2.02-3.75 m) each 955.00
7344 Beam clamp 300-380 mm (450-1070 mm) each set 355.00
7345 Prop 4 m each 910.00
7346 Double coupler each 46.00
8647 Stainless steel screws 30 mm x4 mm 100 Nos 32.00
8659 Water proof ply 12 mm thick sqm 517.00
8953 Micro Silica kg 32.00
8954 Stop end tubes for diaphragmwall 600 mm dia. sqm 4.50
8955 Driving end tubes for diaphragm wall 600 mm dia. sqm 72.00
9977 Carriage L.S. 2.00
9988 Carriage and sundries L.S. 2.00
9999 Sundries L.S. 2.00

5.0 REINFORCED CEMENT CONCRETE

No.
CAST IN SITU
5.1 Providing and laying in position specified grade of reinforced cement
concrete, excluding the cost of centering, shuttering, finishing and
reinforcement - All work up to plinth level :
5.1.2 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone
aggregate 20 mm nominal size) cum 7718.25
5.1.3 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone
5.2 Reinforced cement concrete work in walls (any thickness), including
attached pilasters, buttresses, plinth and string courses, fillets, columns,
pillars, piers, abutments, posts and struts etc. above plinth level up to
floor five level, excluding cost of centering, shuttering, finishing and
reinforcement :
5.2.2 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone
5.3 Reinforced cement concrete work in beams, suspended floors, roofs having
slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain
window sills, staircases and spiral stair cases above plinth level up to
floor five level, excluding the cost of centering,
shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse
sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). cum 9763.80
5.4 Providing and laying up to floor five level reinforced cement concrete in
kerbs, steps and the like excluding the cost of centering, shuttering,
finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse
5.5 Reinforced cement concrete work in arches, archribs, domes, vaults,
shells, folded plate and roofs having slope more than 15° up to floor five
level, excluding the cost of centering, shuttering, finishing and
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3
graded stone aggregate 20 mm nominal size). cum 10289.00
5.6 Reinforced cement concrete work in chimneys, shafts, up to floor five
level, excluding the cost of centering, shuttering, finishing and
reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3
5.7 Reinforced cement concrete work in well-steining, excluding the cost of
centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement
: 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal
size). cum 7270.30
5.8 Reinforced cement concrete work in vertical and horizontal fins individually
or forming box louvers, facias and eaves boards above plinth level up to
floor five level, excluding the cost of centering, shuttering, finishing and
reinforcement with 1:1½:3 (1 cement : 1½ coarse sand(zone-III) : 3
graded stone aggregate 20mm nominal size). cum 8550.25

No.
FORM WORK
5.9 Centering and shuttering including strutting, propping etc. and removal
of form for :
5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 284.85
5.9.2 Walls (any thickness) including attached pilasters, butteresses,
plinth and string courses etc. sqm 609.30
5.9.3 Suspended floors, roofs, landings, balconies and access
platform sqm 693.05
5.9.4 Shelves (Cast in situ) sqm 693.05
5.9.5 Lintels, beams, plinth beams, girders, bressumers and
cantilevers sqm 552.05
5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 733.70
5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 622.35
5.9.8 Spiral staircases (including landing) sqm 600.00
5.9.9 Arches, domes, vaults up to 6 m span sqm 1713.20
5.9.10 Extra for arches, domes, vaults exceeding 6 m span sqm 560.65
5.9.11 Chimneys and shafts sqm 609.30
5.9.12 Well steining sqm 246.40
5.9.13 Vertical and horizontal fins individually or forming box louvers
band, facias and eaves boards sqm 1023.55
5.9.14 Extra for shuttering in circular work (20% of respective centering
and shuttering items) sqm 20.00%
5.9.15 Small lintels not exceeding 1.5 m clear span, moulding as in
cornices, window sills, string courses, bands, copings, bed
plates, anchor blocks and the like sqm 284.85
5.9.16 Edges of slabs and breaks in floors and walls
5.9.16.1 Under 20 cm wide metre 173.25
5.9.16.2 Above 20 cm wide sqm 737.30
5.9.17 Cornices and mouldings sqm 740.25
5.9.18 Small surfaces such as cantilever ends, brackets and ends
of steps, caps and bases to pilasters and columns and the like sqm 773.70
5.9.19 Weather shade, Chajjas, corbels etc., including edges sqm 766.75
5.9.20 Suspended floors, roofs, landings, balconies and access
platform with water proof ply 12 mm thick sqm 779.30
5.9.21 Lintels, beams, plinth beams, girders, bressumers and
cantilevers with water proof ply 12 mm thick sqm 641.60
5.10 Providing and fixing tie bolt, spring coil and plastic cone in wall shuttering
complete as per the direction of Engineer-in-charge.
5.10.1 12 mm dia. & 100 mm length each set 140.80

No.

5.10.4 20 mm dia.& 225 mm length each set 179.60
5.11 Extra for additional height in centering, shuttering where ever required
with adequate bracing, propping etc., including cost of de-shuttering
and decentering at all levels, over a height of 3.5 m, for every additional
height of 1 metre or part thereof (Plan area to be measured).
5.11.1 Suspended floors, roofs, landing, beams and balconies
(Plan area to be measured) sqm 287.50
PRE-CAST RCC
5.12 Providing, hoisting and fixing above plinth level up to floor five level precast
reinforced cement concrete work in string courses, bands, copings,
bed plates, anchor blocks, plain window sills and the like, including the
cost of required centering, shuttering but , excluding cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3
5.13 Providing, hoisting and fixing up to floor five level precast reinforced cement
concrete in small lintels not exceeding 1.5m clear span up to floor five
level, including the cost of required centering, shuttering but , excluding
the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-
III) : 3 graded stone aggregate 20 mm nominal size). cum 12464.25
reinforced cement concrete in mouldings as in cornices, windows sills
etc, including setting in cement mortar 1:3 (1 cement : 3 coarse sand)
cost of required centering, shuttering but, excluding the cost of
reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3
reinforced cement concrete in lintels, beams and bressumers, including
setting in cement mortar 1:3 (1 cement : 3 coarse sand), cost of required
centering and shuttering but , excluding the cost of reinforcement, with
1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate
20 mm nominal size) cum 11351.35
reinforced cement concrete in shelves, including setting in cement mortar
1:3 (1cement : 3 coarse sand), cost of required centering, shuttering
and finishing with neat cement punning on exposed surfaces but ,
excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse
reinforced cement concrete in vertical & horizontal fins, individually or
forming box louvers, setting in cement mortar 1:2 (1 cement : 2 coarse
sand), including the cost of required centering, shuttering but , excluding
the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-
III) : 3 graded stone aggregate 20 mm nominal size). cum 9948.80

No.
5.18 Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse

sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced
with 1.6 mm dia mild steel wire, including centering and shuttering,
roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement:
3 fine sand) etc. complete, excluding plastering of the jambs, sills and
soffits.
5.18.1 50 mm thick sqm 1474.05
5.18.2 40 mm thick sqm 1329.75
5.18.3 25 mm thick sqm 1194.95
ENCASING ROLLED STEEL SECTION
5.19 Encasing rolled steel sections, in beams and columns, with cement
concrete 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone
aggregate 20 mm nominal size), including centering and shuttering
complete but , excluding cost of reinforcement. cum 13020.50
5.20 Encasing rolled steel section in grillages with cement concrete 1:1.5:3
(1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20
mm nominal size), including centering and shuttering but, excluding
cost of expanded metal and hangers. cum 8190.10
5.21 Extra for providing and fixing expanded metal mesh of size 20x60 mm
and strands 3.25 mm wide 1.6 mm thick weighing 3.64 kg per sqm for
encasing of rolled steel sections in beams, columns and grillages,
excluding cost of hangers. sqm 443.95
STEEL REINFORCEMENT
5.22 Steel reinforcement for R.C.C. work including straightening, cutting,
bending, placing in position and binding all complete upto plinth level.
5.22.1 Mild steel and Medium Tensile steel bars Kg 82.10
5.22.2 Hard drawn steel wire Kg 85.60
5.22.3 Cold twisted bars Kg 83.50
5.22.4 Hot rolled deformed bars Kg 83.50
5.22.5 Hard drawn steel wire fabric Kg 92.15
5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 83.50
5.22A Steel reinforcement for R.C.C. work including straightening, cutting,
bending, placing in position and binding all complete above plinth level.
5.22A.1 Mild steel and Medium Tensile steel bars Kg 82.10
5.22A.2 Hard drawn steel wire Kg 85.60
5.22A.3 Cold twisted bars Kg 83.50
5.22A.4 Hot rolled deformed bars Kg 83.50
5.22A.5 Hard drawn steel wire fabric Kg 92.15
5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 83.50

No.
5.22B Steel reinforcement for R.C.C. work ready to use "cut and bend"
rebars of approved make from factory/workshop to construction
site including placing in position and binding all complete upto
plinth level.
5.22B.1 Thermo-Mechanically Treated bars of grade Fe-500D or
more. Kg 77.65
5.22C Steel reinforcement for R.C.C. work ready to use "cut and bend"
rebars of approved make from factory/workshop to construction
site including placing in position and binding all complete above
plinth level.
5.22C.1 Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 77.65
MISCELLANEOUS
5.23 Smooth finishing of the exposed surface of R.C.C. work with 6 mm
thick cement mortar 1:3 (1 Cement : 3 fine sand). sqm 227.35
5.24 Extra for rendering smooth the top of suspended floors, landings and
staircases (treads and risers) with cement mortar 1:2 (1 cement : 2
coarse sand), including a floating coat of neat cement and protecting
the surface with a layer of 7.5 cm of earth laid over 15 mm of fine sand
in case of suspended floor and bricks laid in mud mortar in case of
landings and steps, including subsequent removal and cleaning of the
same. sqm 125.10
5.25 Providing and fixing in position copper plate as per design for expansion
joints. Kg 728.20
5.26 Providing and filling in position, blown bitumen in expansion joints. cum 61509.80
5.27 Providing and filling in position bitumen mix filler of proportion 80 kg. of
hot bitumen, 1 kg. of cement and 0.25 cubic metre of coarse sand for
expansion joints. cum 21054.50
5.28 Providing and fixing in position 12mm thick bitumen impregnated per cm
fiber board conforming to IS: 1838, including cost of primer, sealing depth per
compound Grade-A in expansion joints. 100m 557.65
5.29 Providing and fixing sheet covering over expansion joints with iron screws
as per design.
5.29.1 Non-asbestos fibre cement board 6 mm thick as per IS: 14862.
5.29.1.1 150mm wide metre 190.50
5.29.1.2 200mm wide metre 256.25
5.29.2 Aluminium fluted strips 3.15 mm thick.
5.29.2.1 150 mm wide metre 493.40
5.29.2.2 200 mm wide metre 654.95
5.29.3 Cement bonded wood particle board 6mm thick as per IS : 14276
5.29.3.1 150 mm wide metre 187.35
5.29.3.2 200 mm wide metre 252.00
5.30 Add for plaster drip course/ groove in plastered surface or moulding to
R.C.C. projections. metre 58.90
No.
5.31 Extra for laying reinforced cement concrete in or under water and/ or
liquid mud, including cost of pumping or bailing out water and removing
slush etc., complete. cum 794.65
Note For Item No. 5.31:- The quantity will be calculated by multiplying
the depth measured from the subsoil water level up to the centre of gravity
of the R.C.C. under subsoil water with the quantity of R.C.C. in cubic
metre executed under subsoil water. The depth of centre of gravity shall
be reckoned correct to 0.1 m. 0.05 m or more shall be taken as 0.1 m
and less than 0.05 m ignored. No extra payment shall be made for placing
reinforcement or centering & shuttering under sub - soil water conditions.
5.32 Extra for laying reinforced cement concrete in or under foul positions. cum 336.55
DESIGN MIX CONCRETE
5.33 Providing and laying in position machine batched and machine mixed
design mix M-25 grade cement concrete for reinforced cement concrete
work, using cement content as per approved design mix, including
pumping of concrete to site of laying but excluding the cost of centering,
shuttering, finishing and reinforcement, including admixtures in
recommended proportions as per IS: 9103 to accelerate, retard setting
of concrete, improve workability without impairing strength and durability
as per direction of Engineer-in-charge.
(Note :- Cement content considered in this item is @ 330 kg/cum. Excess/
less cement used as per design mix is payable/recoverable separately).
5.33.1 All works upto plinth level cum 7997.30
5.33.2 All works above plinth level upto floor V level cum 9400.85
5.34 Extra for providing richer mixes at all floor levels.
Note:- Excess/less cement over the specified cement content used is
payable /recoverable separately.
5.34.1 Providing M-30 grade concrete instead of M-25 grade BMC/
RMC. (Note:- Cement content considered in M-30 is @
340 kg/cum) cum 69.75
RMC. (Note : Cement content considered in M-35 is @
350 kg/ cum) cum 139.45
RMC.(Note : Cement content considered in M-40 is @
360 kg/ cum) cum 209.20
5.35 Add for using extra cement in the items of design mix over and above
the specified cement content therein. quintal 673.30
5.36 Providing and placing in position precast reinforced cement concrete
waffle units, square or rectangular, as per design and shape for floors
and roofs in 1:1½:3 (1 Cement : 1½ coarse sand (zone-III) : 3 graded
stone aggregate 10 mm nominal size), including flush or deep ruled
pointing at joints in Cement mortar 1:2 (1 Cement : 2 Fine sand), making
necessary holes of required sizes for carrying through service lines
etc., providing steel hooks for lifting etc, form work in precasting,
handling, hoisting, centering and erection complete for all floor levels
but, excluding the cost of reinforcement. cum 25483.10
No.
5.37 Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using cement content as per approved
design mix, manufactured in fully automatic batching plant and
transported to site of work in transit mixer for all leads, having continuous
agitated mixer, manufactured as per mix design of specified grade for
reinforced cement concrete work, including pumping of R.M.C. from
transit mixer to site of laying , excluding the cost of centering, shuttering
finishing and reinforcement, including cost of admixtures in recommended
proportions as per IS : 9103 to accelerate/ retard setting of concrete,
improve workability without impairing strength and durability as per
direction of the Engineer-in-charge.
(Note :- Cement content considered in this item is @ 330 kg/
cum.Excess/less cement used as per design mix is payable/recoverable
separately).
5.37.1 All works upto plinth level cum 8398.65
5.37.2 All works above plinth level upto floor V level cum 9802.20
5.38 Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four
floors or part thereof. cum 280.95
5.40 Providing and laying in position ready mixed M-25 grade concrete for
reinforced cement concrete work, using fly ash and cement content as
per approved design mix, and manufactured in fully automatic batching
plant and transported to site of work in transit mixer for all leads, having
continuous agitated mixer, manufactured as per mix design of specified
grade for reinforced cement concrete work, including pumping of R.M.C.
from transit mixer to site of laying, excluding the cost of centering,
shuttering, finishing and reinforcement, including cost of admixtures in
recommended proportions as per IS : 9103 to accelerate / retard setting
of concrete, improve workability without impairing strength and durability
as per direction of the Engineer - in - charge.
NOTE- (1) Cement content considered in this item is @ 330 kg/cum.
Excess/ less cement used as per design mix is payable/ recoverable
separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be
used as part replacement of OPC as per IS : 456. Uniform blending with
cement to be ensured in accordance with clauses 5.2 and 5.2.1 of
IS:456 -2000 in the items of BMC and RMC.
5.40.1 All works up to Plinth level. cum 8365.80
5.40.2 All works above plinth & up to floor V level. cum 9769.35
Note :- The above item shall be used judiciously where specified quality
of Fly Ash is available for mixing in concrete. Also, the guidelines issued
by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated
9th April 2009 shall be followed in such cases.
5.41 Supplying and applying pre tested and approved water based concrete
curing compound to concrete/ masonry surface, all as per manufacturer’s
specification and direction of Engineer-in-charge.
5.41.1 Non pigmented wet curing compound sqm 53.90

No.
5.42 Providing and fixing parallel threaded couplers conforming to IS code on

“Reinforcement Couplers for Mechanical Splices of Bars for Concrete
Reinforcement - Specification”, to reinforcement bars including threading,
enlargement at connection by forging, protecting the prepared
reinforcement bars and related operations as required to complete the
works per direction of Engineer- in-Charge.
5.42.1 Coupler for 16 mm diameter reinforcement bar each 97.80
5.43 Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm
thick as per design for expansion joints.
5.43.1 200 mm wide. metre 711.90
5.43.2 300 mm wide. metre 1006.25
5.44 Providing and fixing of expansion joint system related with floor location
as per drawings and direction of Engineer-In-Charge. The joints system
will be of extruded aluminum base members, self aligning / self centering
arrangement and support plates etc. as per ASTM B221-02. The system
shall be such that it provides floor to floor /floor to wall expansion control
system for various vertical localtion in load application areas that
accommodates multi directional seismic movement without stress to
it's components. System shall consist of metal profiles with a universal
aluminum base member designed to accommodate various project
conditions and finish floor treatments. The cover plate shall be designed
of width and thickness required to satisfy projects movement and loading
requirements and secured to base members by utilizing manufacturer’s
pre-engineered self- centering arrangement that freely rotates / moves
in all directions. The Self - centering arrangement shall exhibit circular
sphere ends that lock and slide inside the corresponding aluminum
extrusion cavity to allow freedom of movement and flexure in all directions
including vertical displacement. Provision of Moisture Barrier Membrane
in the Joint System to have watertight joint is mandatory requirement
all as per the manufactures design and as approved by Engineer -in-
Charge. (Material shall confirm to ASTM 6063).
5.44.1 Floor Joint of 100 mm gap metre 5594.85
5.45 Providing and fixing of expansion joint system related with wall joint (internal/
external) location as per drawings and direction of Engineer-In- Charge.
The joints shall be of extruded aluminum base members, self aligning /
centering arrangement and support plates as per ASTM B221- 02. The
material shall be such that it provides an Expansion Joints System
suitable for vertical wall to wall/ wall to corner application, both new and
existing construction in office Buildings & complexes with no slipping
down tendency amongst the components of the Joint System. The Joint
System shall utilize light weight aluminum profiles exhibiting minimal

No.
exposed aluminum surfaces mechanically snap locking the multicellular

to facilitate movement. (Material shall confirm to ASTM 6063).
5.45.1 Wall Joint of 100 mm gap metre 4658.30
5.46 Providing and fixing of expansion joint system of approved make and
manufactures for various roof locations as per approved drawings and
direction of Engineer-In-Charge. The joints shall be of extruded aluminum
base members with, self aligning and self centering arragement support
plates asper ASTM B221-02. The system shall be such that it provides
watertight roof to roof/roof to corner joint cover expansion control system
that is capable of accommodating multidirectional seismic movement
without stress to its components. System shall consist of metal profile
that incorporates a universal aluminum base member designed to
accommodate various project conditions and roof treatments. The cover
plate shall be designed of width and thickness required to satisfy
movement and loading requirements and secured to base members by
utilizing manufacturer’s pre-engineered self-centering arrangement that
freely rotates / moves in all directions. The Self centering arrangement
shall exhibit circular sphere ends that lock and slide inside the
corresponding aluminum extrusion cavity to allow freedom of movement
and flexure in all directions including vertical displacement. The Joint
System shall resists damage or deterioration from the impact of falling
ice, exposure to UV, airborne contaminants and occasional foot traffic
from maintenance personnel. Provision of Moisture Barrier Membrane
in the Joint System to have water tight joint is mandatory requirement.
(Material shall confirm to ASTM 6063.)
5.46.1 Roof Joint of 100 mm gap metre 5193.45
5.47 Providing and fixing in position factory made precast RCC M-40 fixing
with hold fast embedded in 1:3:6 concrete block for doors and windows
frames having excellent smooth finish as per IS: 6523 with reinforcement
of 3 Nos, 6 mm dia main bars tied with 3 mm M.S stirrups placed @
200 mm C/C and 6 numbers high strength polymer blocks of required
size for fixing hinges including providing 6 no specially designed M.S.
galvanised sleeves for accomodating 6 mm dia fully threaded bolts for
fixing hold fast on vertical members, providing suitable arrangement for
recieving sliding door bolts and tower bolt etc all complete, as per the
direction of Engineer in charge. The frame shall be measured in running
metre correct to two places of decimal.
5.47.1 Door frame 125 mmx 60 mm metre 666.85
5.47.2 Door frame 100 mmx 60 mm metre 617.90
5.47.3 Door frame 85 mmx60 mm metre 592.25
5.48 Providing and laying Reinforced cement concrete for construction of
piers, abutments, portal frames, pier caps and bearing pedestals and
seismic arresters over pier/ abutment caps at all locations with specified

No.
grade using Ordinary Portland Cement (conforming to strength

requirement of IS:8112) including the cost of steel centering and
shuttering etc. complete including testing of materials etc. for casting
pier & pier cap in one/two stage, necessary tools, plants, machinery
and all related operations as required to complete the work as per
drawings and Specifications with all leads, lifts and depths true to level
and position but excluding the cost of providing reinforcement.
(Reinforcement shall be measured and paid separately.)
Note:- Cement content considered in this item is 480 Kg./ Cum. Excess/
less cement used as per design mix is payable/ recoverable separately.
5.48.1 Reinforced Cement Concrete -M-50 cum 7425.00
5.48.2 Reinforced Cement Concrete -M-60 cum 8681.45
5.48.3 Extra for using M -50/ M-60 Grade Self-compacting Cement
Concrete cum 748.60
5.49 Constructing cast-in situ RCC diaphragm wall by providing and laying
machine batched, machine mixed, self compacting, ready mix reinforced
cement concrete, tramie controlled, of M 30 grade using minimum 400
kg. cement per cum of concrete including providing and mixing required
admixtures in recommended proportions as per IS : 9103, as approved
by the Engineer-in-charge, for achieving 150- 200mm slump, for
diaphragm wall having thickness as per approved structural design not
exceeding 600 mm, in pannels of required depth and lengths as per
approved drawing, including constructing necessary guide walls as
required and as specified including boring in all kinds of soils and rocks,
including working in or under water and / or liquid mud, in foul conditions
and pumping or bailing out of water and removing slush, including disposal
of earth/ rock / slush etc. for all leads and all lifts, including preparing,
providing and re-circulating bentonite slurry in the trench as and when
required for all depths, including agitating bentonite slurry during trenching
etc., providing and fixing stop ends or form tubes, upto the required
depth of diaphragm wall including extracting the same after casting,
including chipping off the bentonite adulterated concrete or unsound
concrete up to the cut off level for obtaining the sound concrete, dressing
undulations on the exposed face of diaphragm wall after excavation by
chipping / chiseling etc. including filling the depression/ cavities with
sound concrete etc. complete and as directed by the Engineer-in-charge,
including providing recess for bearing plates and fixing insert boxes for
inclined rock anchors etc. complete as per the specifications and
approved design and as directed by the Engineer-in-charge, but excluding
the cost of reinforcement and inserts. (rates include cost of all inputs of
labour, material and T & P, cost of handling, lifting & placing in position
the reinforcement cage in the trench, including the additional cost of
welding the reinforcement bars etc. involved in the work and all other
incidental expenditure for completing the work as directed by the
Engineer-in-charge), However, the actual area of the diaphragm wall,
correct to two places of decimal, from design bottom level to the design
cut off level (including portion anchored in the rock upto the design
bottom level) only shall be measured for payment.
“Excess/less cement used for design mix including the extra cement
required for under water concreting is payable / recoverable separately. cum 16618.70

SUB HEAD : 6.0
MASONRY WORK
105
BASIC RATES (SH: 6.0 MASONRY WORK)
No.
0037 Mobile crane day 7500.00
0100 Bandhani day 617.00
0155 Mason (average) day 709.00
0322 Bitumen felt :Type 3 grade 1 sqm 70.00
0357 Polymer modified adhesive mortar kg 15.00
1002 Mild steel round bar 12 mm dia and below quintal 4500.00
1008 Flats up to 10 mm in thickness quintal 4500.00
1235 Diesel litre 73.50
1984 Common burnt clay F.P.S. bricks tile class designation 10 1000 Nos 4500.00
1986 Common burnt clay modular bricks class designation 12.5 1000 Nos 5000.00
2201 Carriage of Bricks 1000 Nos 276.72
2207 Carriage of Brick tiles 1000 Nos 166.03
2208 Carriage of Lime cum 103.77
2602 Common burnt clay F.P.S. (non modular) bricks class designation 1000 Nos 4500.00
7008 F.P.S. (non modular) clay fly ash bricks class designation 7.5 1000 Nos 4800.00
SUB HEAD : 6.0 MASONRY WORK 106

No.
7736 Extruded burnt flyash clay sewer bricks conforming to I.S 4885 1000 Nos 5400.00
7737 Fly ash bricks conforming to I.S. 12894 1000 Nos 4300.00
7738 Calcium Silicate Bricks machine moulded conforming to I.S. 4139 1000 Nos 5400.00
7900 Modular common burnt clay bricks of class designation 7.5 1000 Nos 4000.00
7901 Machine moulded perforated common burnt clay FPS

(non modular) bricks of class designation 12.5 1000 Nos 4700.00
7902 Machine moulded common burnt clay modular perforated bricks

of class designation 12.5 1000 Nos 5200.00
7903 Machine moulded common burnt clay FPS (non modular) bricks
of class designation 12.5 1000 Nos 5000.00
7904 Machine moulded common burnt clay tile bricks of class

designation 12.5 1000 Nos 4900.00
8655 Autoclaved aerated cement (AAC) blocks cum 2600.00
8656 Gypsum panel 666 X 500 X 100 mm size sqm 480.00
8657 Bonding plaster for Gypsum panel kg 25.00

6.0 MASONRY WORK

No.
6.1 Brick work with common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 in foundation and plinth in:
6.1.1 Cement mortar 1:4 (1 cement : 4 coarse sand) cum 6376.25
6.2 Brick work with common burnt clay modular bricks of class designation
7.5 in foundation and plinth in:
6.2.2 Cement Mortar 1:6 (1 cement : 6 coarse sand). cum 5302.60
6.3 Brick work with common burnt clay machine moulded perforated bricks of
class designation 12.5 conforming to IS: 2222 in superstructure above plinth
level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) :
6.3.1 With F.P.S.(non modular) bricks cum 7722.65
6.3.2 With Modular bricks cum 7501.50
6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class
designation 7.5 in superstructure above plinth level up to floor V level in
all shapes and sizes in :
6.5 Extra for brick work / AAC block masonry / Tile brick masonry in
superstructure above floor V level, for each four floors or part thereof by
mechanical means. cum 236.65
6.6 Extra for forming cavity 5 cm to 11.5 cm wide in cavity walls with
necessary weep and vent holes including use of cores and cost of
providing and fixing bitumastic coated M .S. ties 300 mm long of 25x
3 mm section at not less than 3 ties per sqm as per approved design. sqm 176.25
6.7 Providing half brick masonry with common burnt clay F.P.S. (non modular)
bricks of class designation 7.5 in cement mortar 1:3 (1 Cement : 3
coarse sand) in superstructure for closing cavity 5 to 7.5 cm wide in
cavity wall complete with 10cm / 11.4 cm wide bitumen felt type 3
grade 1. metre 254.00
6.8 Brick work 7 cm thick with common burnt clay F.P.S. (non modular)
brick of class designation 7.5 in cement mortar 1:3 (1 cement : 3
coarse sand) in superstructure above plinth level and upto floor five
level. sqm 749.75
6.9 Brick work in plain arches in superstructure above plinth level and upto
floor five level including centering and shuttering complete for span up
to 6 metres with common burnt clay F.P.S. (non modular) bricks of
class designation 7.5 in cement mortar 1:3 (1 cement : 3 coarse sand). cum 12352.95
6.10 Brick work in gauged arches in superstructure above plinth level and
upto floor five level in cement mortar 1:3 (1 cement : 3 coarse sand)
including centering and shuttering complete, for span up to 6 meters
with common burnt clay F.P.S. (non modular) bricks of class designation 7.5. cum 15361.90

No.
6.11 Extra for additional cost of centering for arches exceeding 6m span
including all shuttering, bolting, wedging and removal (Area of the soffit
to be measured). sqm 560.65
HALF BRICK MASONRY
6.12 Half brick masonry with common burnt clay F.P.S. (non modular) bricks
of class designation 7.5 in foundations and plinth in :
6.12.1 Cement mortar 1:3 (1 cement : 3 coarse sand) sqm 798.25
6.12.2 cement mortar 1:4 (1 cement : 4 coarse sand) sqm 773.75
6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks
of class designation 7.5 in superstructure above plinth level up to floor
V level.
6.13.1 Cement mortar 1:3 (1 cement :3 coarse sand) sqm 956.60
6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) sqm 932.10
6.14 Extra for half brick masonry in superstructure, above floor V level for
every four floors or part thereof by mechanical means. sqm 20.95
6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at
every third course of half brick masonry. sqm 80.10
BRICK TILE WORK
6.16 Tile brick masonry with common burnt clay F.P.S. (non modular) tile
bricks of class designation 10 in foundation and plinth in:
6.17 Tile brick masonry with common burnt clay machine moulded tile bricks
of class designation 12.5 conforming to IS : 2690 (Part I) in foundation
and plinth in cement mortar 1:6 (1 cement : 6 coarse sand). cum 9716.75
bricks of class designation 10 in superstructure above plinth level up to
floor V level in cement mortar 1:6 (1 cement : 6 coarse sand). cum 10808.25
bricks of class designation 10 in plain arch work in superstructure
above plinth and upto floor five level in cement mortar 1:4 (1 cement : 4
coarse sand) including centering and shuttering complete. cum 15551.35
bricks of class designation 10 in gauged arch work in superstructure
above plinth and upto floor five level in cement mortar 1:4 (1 cement : 4
coarse sand) including centering and shuttering complete. cum 18567.55
6.22 Tile brick masonry work 5 cm thick with common burnt clay F.P.S.
(non modular) tile bricks of class designation 10 in cement mortar 1:3
(1 cement : 3 coarse sand) in superstructure above plinth and upto
floor five level. sqm 773.25
HONEY COMB WORK
6.23 Honey-comb brick work 10 / 11.4 cm thick with common burnt clay
bricks of class designation 7.5 in super structure above plinth level
upto floor V level with cement mortar 1:4 (1 cement : 4 coarse sand). sqm 594.15

No.
6.24 Extra for laying brick work in or under water and/ or liquid mud
including cost of pumping or bailing out water and removing slush etc. cum per
complete. metre depth 794.65
NOTE :- The quantity will be calculated by multiplying the depth
measured from sub - soil water level up to the centre of gravity of brick
work under sub - soil water with the quantity of brick work in cum.
executed under the sub - soil water. The depth of centre of gravity shall
be reckoned correct to 0.1 m, 0.05 m or more shall be taken as 0.1 m
and less than 0.05 m ignored.
6.25 Extra for laying brick work in or under foul position. cum 336.55
EXPOSED BRICK WALL
6.26 Brick work with common burnt clay selected F.P.S. (non modular) bricks
of class designation 7.5 in exposed brick work including making
horizontal and vertical grooves 10 mm wide 12 mm deep complete in
cement mortar 1:6 (1 cement : 6 coarse sand)
6.26.1 From ground level upto plinth level cum 6324.30
6.26.2 Above plinth level upto floor V level cum 7832.00
6.27 Brick work with common burnt clay modular bricks of class designation
7.5 in exposed brick work including making horizontal and vertical
grooves 10mm wide 12 mm deep complete in cement mortar 1:6 (1
cement : 6 coarse sand).
6.28 Brick work with common burnt clay machine moulded modular bricks
of class designation 12.5 in exposed brick work including making
horizontal and vertical grooves 10 mm wide 12 mm deep complete in
cement mortar 1:6 (1 cement : 6 coarse sand).
6.29 Brick work with common burnt clay machine moulded F.P.S. (non
modular) bricks of class designation 12.5 in exposed brick work including
making horizontal and vertical grooves 10 mm wide 12 mm deep
complete in cement mortar 1:6 (1 cement : 6 coarse sand).
6.30 Brick work with common burnt clay machine moulded perforated F.P.S.
(non modular) bricks of class designation 12.5 conforming IS : 2222 in
exposed brick work including making horizontal and vertical grooves
10mm wide 12 mm deep complete in cement mortar 1:6 (1 cement : 6
coarse sand).

No.
6.31 Brick work with common burnt clay machine moulded perforated modular
bricks of class designation 12.5 conforming to IS : 2222 in exposed
brick work including making horizontal and vertical grooves 10 mm wide
12mm deep complete in cement mortar 1:6 (1 cement : 6 coarse sand).
6.32 Brick work with clay flyash F.P.S. (non modular) brick of class
designation 7.5 in superstructure above plinth level up to floor five level
in :
6.34 Brick work with non modular fly ash bricks conforming to IS:12894,
class designation 10 average compressive strength in super structure
above plinth level up to floor V level in :
6.34.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) cum 7280.70
6.35 Brick work with modular calcium silicate bricks machine moulded
conforming to IS:4139, class designation 10 average compressive
strength in super structure above plinth level up to floor V level in :
6.35.2 Cement mortar 1:6 (1 cement : 6 Coarse sand) cum 7997.40
6.36 Brick work with modular extruded brunt fly ash clay sewer bricks
(Conforming to IS: 4885 ) in cement mortar 1:4 (1 cement : 4 coarse
sand) in foundation and plinth :
6.36.1 Cement Mortar 1:4 ( 1 cement : 4 coarse sand) cum 6407.35
6.37 Brick work with modular extruded brunt fly ash clay sewer bricks
(conforming to IS : 4885) in arches in foundation and plinth in cement
mortar 1:3 ( 1 cement : 3 fine sand). cum 11309.95
6.38 Providing and laying autoclaved aerated cement blocks masonry with
100 mm thick AAC blocks in super structure above plinth level up to
floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate
includes providing and placing in position 2 Nos 6 mm dia M.S. bars at
every third course of masonry work. cum 8227.35
6.40 Providing and laying Gypsum panel partitions 100 mm thick with water
proof Gypsum panels of size 666x500x100 mm, made of calcite
phosphor Gypsum fixed with tongue and groove, jointed with bonding
plaster as per manufacturer’s specifications in superstructure above
plinth level up to floor V level. Gypsum blocks will have a minimum
compressive strength of 9.3 kg/cm2 sqm 853.50
6.41 Extra for Gypsum panel Partitions in superstructure above floor V level
for every four floors or part thereof. sqm 129.15
6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common
burnt clay F.P.S. (non modular) bricks of class designation 7.5 including
grouting with cement mortar 1:4 (1 cement : 4 fine sand). metre 52.00

No.
6.45 Half brick masonry with non modular fly ash bricks of class designation
10, conformingio IS :12894, in super structure above plinth and upto
floor V level.
6.45.1 Cement mortar 1 : 3 (1 cement : 3 coarse sand) sqm 941.50
6.45.2 Cement mortar 1 : 4 (1 cement : 4 coarse sand) sqm 917.00
6.47 Providing and laying autoclaved aerated cement blocks masonry with
150mm/230mm/300 mm thick AAC blocks in super structure above
plinth level up to floor V level with RCC band at sill level and lintel level
with approved block laying polymer modified adhesive mortar all
complete as per direction of Engineer-in-Charge. (The payment of RCC
band and reinforcement shall be made for seperately). cum 6636.95

SUB HEAD : 7.0
STONE WORK
113
BASIC RATES (SH: 7.0 STONE WORK)
No.
0125 Mason (for plain stone work) 2nd class day 679.00
0139 Skilled Beldar (for floor rubbing etc.) day 617.00
0373 Cramp Gun metal 25x6x300 mm each 80.00
0873 Copper pins 6 mm dia 7.5 cm long each 10.00
1002 Mild steel round bar 12 mm dia and below quintal 4500.00
1007 Structural steel such as tees, angles channels and R.S. joists quintal 4600.00
1154 Through and bond stone 100 Nos 5000.00
1157 Stone for masonry work cum 1100.00
1160 Red sand stone block 10 cudm 79.00
1161 White sand stone block 10 cudm 205.00
1163 White sand stone slab 75 mm thick (un-dressed) sqm 900.00
1164 Red sand stone slab 40 mm thick (un-dressed) sqm 200.00
1165 White sand stone slab 40 mm thick (un-dressed) sqm 200.00
1166 Red sand stone slab 30 mm thick (un-dressed) sqm 200.00
1169 Kota stone slab 25mm thick (rough chiseled) sqm 301.00
1215 Welding by electric plant cm 2.00
SUB HEAD : 7.0 STONE WORK 114

No.
1237 Cutting marble or sand stone slab up to 50 mm thick by

mechanical device metre 10.00
2215 Carriage of Soling stone & masonry stone cum 122.08
2216 Carriage of Stone blocks white & red sand stone & kota stone
slab tonne 92.24
2750 8 mm thick granite stone tiles (mirror polished of all shades) sqm 700.00
4009 Mild steel tubes hot finished welded type kg 57.00
7339 Stainless steel cramp kg 290.00
7439 8mm thick (mirror polished tiles machine cut edge) Raj Nagar
white sqm 500.00
8683 Red sand stone gang saw cut 30 mm thick sqm 425.00
8684 White sand stone gang saw cut 30 mm thick sqm 560.00
8698 Stainless steel cramps(weight 260 grams) with nuts, bolts and
washer for dry stone cladding each 100.00

7.0 STONE WORK

No.
RANDOM RUBBLE MASONRY
7.1 Random rubble masonry with hard stone in foundation and plinth including
levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12
graded stone aggregate 20 mm nominal size) upto plinth level with :
7.2 Random rubble masonry with hard stone in superstructure above plinth
level and upto floor five level, including leveling up with cement concrete
1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm
nominal size) at window sills, ceiling level and the like.
7.4 Extra for random rubble masonry with hard stone in :
7.4.1 Square or rectangular pillars cum 728.50
7.4.2 Circular pillars cum 2025.50
7.5 Extra for random rubble masonry with hard stone curved on plan for a
mean radius not exceeding 6 m. cum 804.45
COURSED RUBBLE MASONRY
7.6 Coursed rubble masonry (first sort) with hard stone in foundation and
plinth with :
7.7 Coursed rubble masonry (second sort) with hard stone in foundation &
plinth with :
7.8 Coursed rubble masonry with hard stone (first or second sort) in
superstructure above plinth level and upto floor five level.
7.8.1 Masonry work (first sort), in cement mortar 1:6 (1 cement :
6 coarse sand) cum 8718.00
7.8.2 Masonry work (second sort), in cement mortar 1:6 (1 cement:
6 coarse sand) cum 8211.10
7.10 Extra for coursed rubble masonry with hard stone (first or second sort) in:
7.10.2 Circular pillars cum 2301.65
7.11 Extra for coursed rubble masonry with hard stone (first or second sort)
curved on plan for a mean radius not exceeding 6 m. cum 875.35
ASHLAR MASONRY
7.12 Stone work in plain ashlar in super structure upto floor five level in cement
mortar 1:6 (1 cement : 6 coarse sand) including pointing with cement
mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment
matching the stone shade :
7.12.1 One face dressed
7.12.1.1 Red sand stone cum 47132.00
7.12.1.2 White sand stone cum 69604.00
No.
7.12.2 Both face dressed

7.13 Stone work plain ashlar in arches in super structure upto floor V level in
cement mortar 1:3 (1 cement : 3 coarse sand) including centering,
shuttering and pointing with white cement mortar 1:2 (1 white cement :
2 stone dust) with an admixture of pigment matching the stone shade.
7.14 Stone work plain ashlar in domes , in super structure upto floor V level in
cement mortar 1:3 (1 cement : 3 coarse sand) including centering,
shuttering and pointing with white cement mortar 1:2 (1 white cement :
2 stone dust) with an admixture of pigment matching the stone shade.
7.15 Stone work ashlar punched (ordinary) in superstructure upto floor five
level in cement mortar 1:6 (1 white cement : 6 coarse sand) including
pointing with cement mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment matching the stone shade.
7.15.2 Both faced punched
7.16 Extra for stone work, random rubble / coursed rubble masonry / ashlar
masonry above floor V level for every four floors or part thereof. cum 1493.00
7.17 Extra for plain ashlar or ashlar punched in :
7.18 Extra for stone work; plain ashlar or ashlar punched curved on plan with
a mean radius not exceeding 6 m. cum 1670.00
7.19 Extra for additional cost of centering for arches exceeding 6m span
including all strutting, bolting, wedging etc. and removal (area of soffit
to be measured). sqm 560.65

No.
SUNK, MOULDED, CARVED ASHLAR MASONRY

7.20 Stone work ashlar sunk or moulded or sunk and moulded upto floor five
level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing
with white cement mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment matching the stone shade :
7.20.1 Red sand stone cum 67731.00
7.20.2 White sand stone cum 90203.00
7.21 Extra for stone work ashlar sunk or moulded or sunk and moulded or
carved in :
7.21.1 Triangular or Square or rectangular pillars cum 3131.00
7.21.2 Circular or polygonal pillars cum 8871.00
7.22 Extra for stone work ashlar sunk or moulded in cornices. per metre
per cm
girth
(60cm deep) 225.35
MISCELLANEOUS STONE WORK
7.23 Item Shifted to Sub Head 8 as item 8.14
7.24 Extra for stone work (veneer work) curved on plan with a mean radius
not exceeding 6 m. cum 2400.00
7.26 Providing and fixing stone dowels 10x5x2.50 cm cut to double wedge
shape as per design in cement mortar 1:2 (1 cement : 2 coarse sand),
including making the necessary chases. each 45.75
7.28 Providing and fixing sloping chajja of stone 40 mm thick and upto 80 cm
wide beyond the wall as measured along the slope in cement mortar
1:4 (1 cement : 4 coarse sand) with 12 mm diameter anchoring steel
bar, 45 cm long, fixed in each stone and supported on and including
with bricks cove in cement mortar 1:4 (1 cement : 4 coarse sand),
including pointing in cement mortar 1:2 (1 white cement : 2 stone dust)
with an admixture of pigment matching the stone shade :
7.28.1 Red sand stone :
7.28.1.1 With common burnt clay F.P.S.(non modular)
bricks of class designation 7.5 sqm 2081.20
7.28.2 White sand stone :
7.28.2.1 With common burnt clay F.P.S.(non modular)
bricks of class designation 7.5 sqm 2081.20
7.29 Providing and fixing horizontal chajja of stone 40 mm thick and upto 80
cm projection in cement mortar 1:4 (1 cement : 4 coarse sand), including
pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with
an admixture of pigment matching the stone shade :
7.29.1 Red sand stone sqm 1306.75
7.29.2 White sand stone sqm 1306.75

No.
7.30 30 mm red sand stone sun-shade (chisel-dressed) supported on red

sand stone brackets, fixed in walls with cement mortar 1:4 (1 cement :
4 coarse sand), including finishing complete. sqm 1556.40
7.31 Providing and fixing red sand stone brackets 55x22.5x45 cm sunk and
moulded including providing and fixing with 4 Nos gun metal cramp
25x6 mm 30 cm long each 5032.85
7.32 Stone work, plain in copings, cornices, string courses and plinth courses,
upto 75 mm thick in Cement mortar 1:6 (1 cement : 6 coarse sand),
including pointing with white cement mortar 1:2 (1 white cement : 2
stone dust) with an admixture of pigment matching the stone shade.
7.32.1 Red sand stone cum 66408.90
7.32.2 White sand stone cum 88880.00
7.33 Providing and fixing stone jali 40 mm thick throughout in cement mortar
1:3 (1 cement : 3 coarse sand), including pointing in white cement
mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment,
matching the stone shade, jali slab without any chamfers etc.
7.33.1 Red sand stone sqm 11230.40
7.33.2 White sand stone sqm 11230.40
7.34 Extra for laying stone work in or under water and/or liquid mud including cum
cost of pumping or bailing out water and removing slush etc. complete. per metre
depth 794.65
NOTE :- The quantity will be calculated by multiplying the depth
measured from sub-soil water level up to the centre of gravity of stone
work under sub - water with the quantity of stone work in cum executed
under the sub-soil water. The depth of centre of gravity shall be reckoned
correct to 0.1 m, 0.05 m or more shall be taken as 0.1 m and less than
0.05 m ignored.
7.35 Extra for laying stone work in or under foul position. cum 336.55
7.38 Stone tile work for wall lining upto 10 m height with special adhesive
over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand),
including pointing in white cement with an admixture of pigment to match
the stone shade.
7.38.1 8mm thick (mirror polished and machine cut edge)
7.38.1.1 Granite stone of any colour and shade sqm 2537.40
7.38.1.2 Raj Nagar plain white marble/ Udaipur green
marble/ Zebra black marble sqm 2263.10

SUB HEAD : 8.0
CLADDING WORK
120
BASIC RATES (SH: 8.0 CLADDING WORK)
No.
0013 Machine for rubbing of floors day 300.00

0019 Hand Grinder for mirror polish day 250.00
0128 Mate day 617.00
0139 Skilled Beldar (for floor rubbing etc.) day 617.00
0368 White Cement tonne 11200.00
0874 Black colour dark shade pigment kg 70.00
1239 18 mm thick Flamed finish granite stone slab sqm 1000.00
1240 18 mm thick Italian Marble stone slab, Perlato
(slab area up to 0.5 sqm). sqm 3209.00
2209 Carriage of Cement tonne 92.24
2216 Carriage of Stone blocks white & red sand stone & kota
stone slab tonne 92.24
2750 8 mm thick granite stone tiles (mirror polished of all shades) sqm 700.00
2751 8 mm thick marble tiles (polished) Raj Nagar sqm 400.00
4009 M.S. Tube Hot finished welded type Kg 57.00
7244 Table rubbed polished stone 18 mm thick (75x50cm) Agaria
Marble stone - 18 mm thick sqm 1620.00
7245 Table rubbed polished stone 18mm thick (75x50cm) Granite
stone-18 mm thick sqm 1620.00
7295 Granite of any colour, 18 mm thick (slab area upto 0.50 sqm) sqm 1600.00
7297 Granite of any colour, 18 mm thick (slab area above 0.50 sqm) sqm 1800.00
7338 Gun metal cramp kg 315.00
7339 Stainless steel cramp kg 290.00
7430 Wedge expansion hold fastener 1/4" or 6 mm each 11.00
SUB HEAD : 8.0 CLADDING WORK 121

No.
7452 Raj nagar plain white marble (table rubbed and polished) 18 mm
thick (slab area upto 0.50 sqm) sqm 575.00
7453 Raj nagar plain white marble (table rubbed and polished) 18 mm
thick (slab area more than 0.50 sqm) sqm 690.00

8.0 CLADDING WORK

No.
8.1 Marble work gang saw cut (polished and machine cut) of thickness 18
mm for wall lining (veneer work), backing filled with a grout of average 12
mm thick in cement mortar 1:3 (1 cement : 3 coarse sand), including
pointing with white cement mortar 1:2 (1 white cement : 2 marble dust)
with an admixture of pigment to match the marble shade (To be secured
to the backing by means of cramps, which shall be paid for separately)
8.1.1 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra
black marble.
8.1.1.1 Area of slab upto 0.50 sqm sqm 4439.40
8.1.1.2 Area of slab over 0.50 sqm sqm 4615.65
8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished,
premoulded and prepolished, machine cut for kitchen platforms, vanity
counters, window sills, facias and similar locations of required size,
approved shade, colour and texture laid over 20 mm thick base cement
mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement,
mixed with matching pigment, epoxy touch ups, including rubbing, curing,
moulding and polishing to edges to give high gloss finish etc. complete
at all levels.
8.2.1 Raj Nagar Plain white marble/ Udaipur green marble/ Zebra
black marble
8.2.2 Granite of any colour and shade
8.3 Providing edge moulding to 18 mm thick marble stone counters, Vanities
etc., including machine polishing to edge to give high gloss finish etc.
complete as per design approved by Engineer-in-Charge.
8.3.1 Marble work metre 220.35
8.3.2 Granite work metre 376.25
8.4 Extra for fixing marble /granite stone, over and above corresponding
basic item, in facia and drops of width upto 150 mm with epoxy resin
based adhesive, including cleaning etc. complete. metre 434.25
8.5 Extra for providing opening of required size & shape for wash basin/
kitchen sink in kitchen platform, vanity counter and similar location in
marble/ Granite/ stone work, including necessary holes for pillar taps
etc. including moulding, rubbing and polishing of cut edges etc. complete. each 734.55
8.6 Mirror polishing on marble work/Granite work/stone work where ever
required to give high gloss finish complete. sqm 368.00
8.7 Providing and fixing cramps of required size & shape in RCC/ CC / Brick
masonry backing with cement mortar 1:2 ( 1 cement :2 coarse sand),

No.
including drilling necessary hole in stones and embedding the cramp in

the hole (fastener to be paid separately).
8.7.1 Gunmetal cramps kg 627.85
8.7.2 Stainless steel cramps kg 612.60
8.8 Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick
masonry surface backing including drilling necessary holes and the
cost of bolt etc complete.
8.8.1 Wedge expansion type
8.8.1.1 Fastener with threaded dia 6 mm each 33.05
8.9 Stone tile (polished) work for wall lining over 12 mm thick bed of cement
mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm
including pointing in white cement complete.
8.9.1 8mm thick
8.9.1.1 Raj nagar plain white marble/ Udaipur green

marble/ Zebra black marble sqm 2515.40
8.9.1.2 Granite of any colour and shade sqm 2926.85
8.10 Providing and fixing stone slab with table rubbed, edges rounded and
polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal
partitions by cutting a chase of appropriate width with chase cutter and
embedding the stone in the chase with epoxy grout or with cement
concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6
mm nominal size) as per direction of Engineer-in-charge and finished
smooth.
8.10.1 White Agaria Marble Stone sqm 3216.90
8.10.2 Granite Stone of approved shade sqm 3216.90
8.11 Providing and fixing machine cut, mirror/ eggshell polished , Marble
stone work for wall lining (veneer work) including dado, skirting, risers of
steps etc., in required design and pattern wherever required, stones of
different finished surface texture, on 12 mm (average) thick cement
mortar 1:3 (1 cement : 3 coarse sand) laid and jointed with white cement
slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed
with pigment of matching shade, including rubbing, curing, polishing
etc. all complete as per Architectural drawings, and as directed by the
Engineer-in-Charge.
8.11.1 18 mm thick Italian Marble stone slab,Perlato, Rosso verona,
Fire Red or Dark Emperadore etc. sqm 8823.75

No.
8.14 Stone work (machine cut edges) for wall lining etc. (veneer work) upto
10 metre height, backing filled with a grout of average 12 mm thick
cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in
white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture
of pigment matching the stone shade : (To be secured to the backing
and the sides by means of cramps and pins which shall be paid for
separately) :
8.14.1 Red sand stone - exposed face fine dressed with rough
backing.
8.14.1.1 70 mm thick sqm 4460.95
8.14.1.2 60 mm thick sqm 4316.20
8.14.1.3 50 mm thick sqm 4171.80
8.14.1.4 40 mm thick sqm 4026.80
8.14.1.5 30 mm thick sqm 3882.00
8.14.2 Red sand stone - Exposed face machine cut and table
rubbed with rough backing.
8.14.2.1 70 mm thick sqm 6154.70
8.14.2.2 60 mm thick sqm 6010.00
8.14.2.3 50 mm thick sqm 5865.60
8.14.2.4 40 mm thick sqm 5720.60
8.14.2.5 30 mm thick sqm 5575.75
8.14.3 White sand stone - exposed face fine dressed with
rough backing .
8.14.3.1 70 mm thick sqm 6034.30
8.14.3.2 60 mm thick sqm 5664.85
8.14.3.3 50 mm thick sqm 5296.25
8.14.3.4 40 mm thick sqm 4925.00
8.14.3.5 30 mm thick sqm 4556.15
8.14.4 White sand stone - Exposed face machine cut and table
rubbed with rough backing.
8.14.4.1 70 mm thick sqm 7728.10
8.14.4.2 60 mm thick sqm 7358.65
8.14.4.3 50 mm thick sqm 6990.05
8.14.4.4 40 mm thick sqm 6618.80
8.14.4.5 30 mm thick sqm 6249.90
8.14.5 Gang saw cut stone
8.14.5.1 30mm thick White sand stone sqm 2549.75
8.14.5.2 30mm thick Red sand stone sqm 2360.10

No.
8.15 Providing and fixing stainless steel cramps of required size and shape
for anchoring stone wall lining to the backing or securing adjacent stones
in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand),
including making the necessary chases in stone and holes in walls
wherever required. kg 612.60
8.16 Providing and fixing copper pins 7.5 cm long 6 mm diameter for securing
adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2
coarse sand), including making the necessary chases. each 36.20
8.17 Wall lining butch work upto 10m height with Dholpur stone 40 mm thick
rough facing on the exposed surface with stone strips of minimum length
300 mm and required width, including embedding every tenth layer and
bottom most layer in masonry or concrete after making necessary chases
of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12
mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled
pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an
admixture of pigment to match the shade of stone complete as per
direction of Engineer-in-charge. sqm 2388.00
8.18 Stone work (machine cut edges Veneer work) for wall lining upto 10 m
height, backing filled with a grout of 12 mm thick cement mortar 1:3 (1
Cement : 3 coarse sand) and jointed with Cement mortar 1:2 (1 cement
: 2 stone dust), including rubbing and polishing complete. (To be secured
to the backing and the sides by means of cramps and pins which shall
be paid for separately).
8.18.1 Kota stone slabs exposed face dressed and rubbed.
8.18.1.1 25 mm thick sqm 2890.25
8.19 Extra for stone work for wall lining on exterior walls of height more than
10 m from ground level for every additional height of 3 m or part there of. sqm 129.65
STONE WORK DRY CLADDING
8.20 Providing and fixing dry cladding upto 10 metre heights with 30mm thick
gang saw cut stone with (machine cut edges) of uniform colour and
size upto 1mx1m, fixed to structural steel frame work and/ or with the
help of cramps, pins etc. and sealing the joints with approved weather
sealant as per Architectural drawing and direction of Engineer-in-charge.
(The steel frame work, stainless steel cramps and pins etc. shall be
paid for separately).
8.20.1 Red sand stone - 30mm thick gang saw cut stone sqm 2217.75
8.20.2 White sand stone - 30mm thick gang saw cut stone sqm 2407.40
8.21 Providing and fixing structural steel frame (for dry cladding with 30 mm
thick gang saw cut with machine cut edges sand stone) on walls at all
heights using M.S. square/ rectangular tube in the required pattern as
per architectural drawing, including cost of cutting, bending, welding
etc. The frame work shall be fixed to the wall with the help of M.S.
brackets/ lugs of angle iron/ flats etc. which shall be welded to the
frame and embedded in brick wall with cement concrete block 1:2:4 (1
cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size)
of size 300x230x300 mm, including cost of necessary centring and

No.
shuttering and with approved expansion hold fasteners on CC/RCC

surface, including drilling necessary holes. Approved cramps/ pins etc.
shall be welded to the frame work to support stone cladding, the steel
work will be given a priming coat of Zinc primer as approved by Engineer-
in-charge and painted with two or more coats of epoxy paint (Shop
drawings shall be submitted by the contractor to the Engineer-in-charge
for approval before execution). The frame work shall be fixed in true
horizontal & vertical lines/planes. (Only structural steel frame work shall
be measured for the purpose of payment, stainless steel cramps shall
be paid for separately and nothing extra shall be paid). kg 183.35
8.22 Providing and fixing adjustable stainless steel cramps of approved quality,
required shape and size, adjustable with stainless steel nuts, bolts and
washer (total weight not less than 260 gms), for dry stone cladding
fixed on frame work at suitable location, including making necessary
recesses in stone slab, drilling required holes etc complete as per
direction of the Engineer-in-charge. each 327.00
NOTE: Item no 8.14, 8.15, 8.16, 8.17, 8.18, 8.19, 8.20, 8.21 & 8.22
are brought from Sub Head 7 i.e. Stone Work, Item no 7.23, 7.25,
7.27, 7.36, 7.37, 7.39, 7.40, 7.41 & 7.42
8.23 Providing 50x50x50 mm 2nd class teak wood plugs including cutting
brick work and fixing in cement mortar 1:3 (1 cement : 3 fine sand) and
making good the walls etc. each 33.90
8.24 Providing and fixing expandable fasteners of specified size with necessary
plastic sleeves and galvanised M.S. screws including drilling holes in
masonry work /CC/ R.C.C. and making good etc. complete.
8.24.1 25 mm long each 18.95
8.24.2 32 mm long each 20.35
8.24.3 40 mm long each 24.35
8.24.4 50 mm long each 25.70
8.25 Providing and fixing 2nd class teak wood plain lining tongued and grooved,
including wooden plugs complete with necessary screws and priming
coat on unexposed surface.
8.25.1 40 mm thick sqm 6137.70
8.25.2 25 mm thick sqm 4057.75
8.25.3 20 mm thick sqm 3291.15
8.25.4 12 mm thick sqm 2181.80
8.26 Providing and fixing in wall lining flat pressed three layer (medium density)
particle board or graded wood Pre-laminated one side decorative
lamination and other side balancing lamination Grade I, Type II, IS :
12823 marked, including priming coat on unexposed arrangement and
screws etc. complete :
8.26.1 12 mm thick sqm 1269.60
8.26.2 18 mm thick sqm 1431.50
8.26.3 25 mm thick sqm 1799.45
No.
8.27 Providing and fixing specified wood frame work consisting of battens
50x25mm fixed with rawl plug and drilling necessary holes for rawl plug
etc. including priming coat complete.
8.27.1 Kiln seasoned and chemically treated hollock wood cum 165255.05
8.28 Providing and fixing plywood 4 mm thick, one side decorative veneer
conforming to IS: 1328 (type-1), for plain lining / cladding with necessary
screws, including priming coat on unexposed surface with :
8.28.1 Decorative veneer facings of approved manufacture sqm 1551.00
8.29 Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842,
plain lining with necessary screws, priming coat on unexposed surface
etc., complete. sqm 1502.85
8.30 Providing and fixing skirting with Pre-laminated (one side decorative and
other side balancing lamination) flat pressed 3 layer or graded particle
board (medium density) Grade I, Type II, IS :12823 marked, with necessary
fixing arrangements and screws, including drilling necessary holes for
rawl plugs etc. and priming coat on unexposed surface complete :
8.30.1 18 mm thick sqm 1891.50
8.30.2 25 mm thick sqm 2259.40
NOTE: Item No 8.23, 8.24, 8.25, 8.26, 8.27, 8.28, 8.29 & 8.30 are
brought from Sub Head 9 i.e. Wood & PVC Work, Item No. 9.32,
9.33, 9.34, 9.35, 9.36, 9.37, 9.38 & 9.39
8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to
IS: 15622 (thickness to be specified by the manufacturer), of approved
make, in all colours, shades except burgundy, bottle green, black of
any size as approved by Engineer-in-Charge, in skirting, risers of steps
and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3
coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm,
including pointing in white cement mixed with pigment of matching shade
complete. sqm 1030.30
NOTE: Item no 8.31 is brought from Sub Head 11 i.e. Flooring,
Item No 11.36
8.32 Designing, fabricating, testing, installing and fixing in position Curtain
Wall with Aluminium Composite Panel Cladding, with open grooves for
linear as well as curvilinear portions of the building , for all heights and
all levels etc. including:
(a) Structural analysis & design and preparation of shop drawings for
pressure equalisation or rain screen principle as required, proper drainage
of water to make it watertight including checking of all the structural
and functional design.
(b) Providing, fabricating and supplying and fixing panels of aluminium
composite panel cladding in pan shape in metalic colour of approved
shades made out of 4mm thick aluminium composite panel material
consisting of 3mm thick FR grade mineral core sandwiched between
two Aluminium sheets (each 0.5mm thick). The aluminium composite
panel cladding sheet shall be coil coated, with Kynar 500 based PVDF
/ Lumiflon based fluoropolymer resin coating of approved colour and

No.
shade on face # 1 and polymer (Service) coating on face # 2 as specified

using stainless steel screws, nuts, bolts, washers, cleats, weather
silicone sealant, backer rods etc.
(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip
Galvanised with serrations and serrated washers to arrest the wind load
movement, fasteners, SS 316 Pins and anchor bolts of approved make
in SS 316, Nylon separators to prevent bi-metallic contacts all complete
required to perform as per specification and drawing The item includes
cost of all material & labour component, the cost of all mock ups at
site, cost of all samples of the individual components for testing in an
approved laboratory, field tests on the assembled working curtain wall
with aluminium composite panel cladding, cleaning and protection of
the curtain wall with aluminium composite panel cladding till the handing
over of the building for occupation. Base frame work for ACP cladding is
payable under the relevant aluminium item.s The Contractor shall provide
curtain wall with aluminium composite panel cladding, having all the
performance characteristics all complete , as per the Architectural
drawings, as per item description, as specified, as per the approved
shop drawings and as directed by the Engineer-in-Charge. However, for
the purpose of payment, only the actual area on the external face of the
curtain wall with Aluminum Composite Panel Cladding (including width
of groove) shall be measured in sqm. up to two decimal places. sqm 4309.80
NOTE: Item No. 8.32 is brought from Sub Head 25 i.e. Structural
Glazing Aluminium Composite Panel, Item No. 25.7

SUB HEAD : 9.0
WOOD AND P.V.C. WORK
130
BASIC RATES (SH: 9.0 WOOD AND P.V.C. WORK)
No.
0111 Carpenter 1st class day 738.00
0119 Glazier day 679.00
0130 Mistry day 738.00
0131 Painter day 679.00
0156 Carpenter (average) day 709.00
0162 Labour for fabrication of uPVC extruded casement/ sliding windows
and doors including drilling holes, fixing of fittings & hardwares, hire
charges of drill machine and electricity charges etc. sqm 485.00
0163 Labour for installation of uPVC extruded casement/ sliding windows
and doors including scaffolding sqm 430.00
0237 Multi purpose fibre (high impact poly propelene reinforced) cement
board 8 mm thick sqm 220.00
0243 8 mm thick mulitipurpose cement bonded wood particle board
conforming to IS : 14276 sqm 215.00
0305 Bamboo 25 mm dia 2.5 metre long score 400.00
0341 Flat pressed 3 layer particle board (medium density) Grade 1,
12 mm thick sqm 288.00
0346 Extra for veneered particle board with Teak veneering on one side
and commercial veneering on other side sqm 230.00
0347 Extra for veneered particle board with Commercial veneering on
both sides sqm 155.00
0348 Extra for veneered particle board with Teak veneering on both sides sqm 500.00
0378 Brass butt hinges (light/ordinary type) : 125x70x4 mm 10 Nos 775.00
0379 Brass butt hinges (light/ordinary type) : 100x70x4 mm 10 Nos 625.00
0380 Brass butt hinges (light/ordinary type) : 75x40x2.5 mm 10 Nos 380.00
0381 Brass butt hinges (light/ordinary type) : 50x40x2.5 mm 10 Nos 155.00
0382 Brass butt hinges (heavy type) : 125x85x5.5 mm(0.70 kg) 10 Nos 1309.00
0383 Brass butt hinges (heavy type) : 100x85x5.5 mm(0.56 kg) 10 Nos 997.00
0384 Brass butt hinges (heavy type) :75x65x4.0 mm (weighing not
less than 0.20 kg) 10 Nos 838.00
SUB HEAD : 9.0 WOOD AND P.V.C. WORK 131

No.
0385 Brass parliamentary hinges 150x125x27x5 mm 10 Nos 2610.00

0388 Brass parliamentary hinges 75x100x20x3.2 mm 10 Nos 1870.00
0400 Brass tower bolt (barrel type) 250x10 mm each 257.00
0408 Brass handles 125 mm with plate 175x32 mm each 144.00
0411 Brass door latch 300x16x5 mmweighing not less than 0.380 kg each 185.00
0412 Brass door latch 250x16x5 mm weighing not less than 0.350 kg each 175.00
0413 Brass mortice latch and lock 100x65 mm with 6 levers and a pair
of brass lever handles each 400.00
0414 Brass mortice latch 100x65mm with a pair of brass lever handles each 310.00
0423 Brass casement window fastener each 45.00
0424 Brass casement stays (straight peg type) 300 mm weighing not
less than 0.33 kg each 126.00
0431 Brass hasps and staples (safety type) 150 mm 10 Nos 740.00
0438 Brass night latch each 610.00
0447 Brass cupboard knob or wardrobe knob 50 mm each 36.00
0449 Brass screws 50 mm 100 Nos 220.00
0552 75 mm SS fancy handle for Kitchen Cabinet 10 Nos 255.00
0555 Chromium plated Brass handles 125 mm with plate 175 x32 mm each 160.00
0556 Chromium plated Brass handles 100 mm with plate 150 x 32 mm each 140.00
0557 Chromium plated Brass handles 75mm with plate 125x32 mm each 125.00
0558 Chromium plated Brass mortice latch and lock 100x65 mm with
6 levers and a pair of brass lever handles each 470.00
0568 Chromium plated brass casement window fastener each 90.00

No.
0569 Chromium plated Brass casement stays (straight peg type)
300 mm weighing not less than 0.33 kg each 140.00
0583 Chromium plated Brass Night latch each 500.00
0584 Chromium plated Brass Wardrobe Knob 50 mm each 80.00
0585 Chromium plated Brass screws 50 mm 100 Nos 300.00
0590 Chromium plated Brass curtain rod 12 mm dia 1.25mm thick metre 185.00
0594 Bright finished or black enameled mild steel butt hinges
125x65x 2.12 mm 10 Nos 135.00
100x58x 1.90 mm 10 Nos 80.00
75x47x 1.70 mm 10 Nos 56.00
50x37x 1.50 mm 10 Nos 49.00
0608 Nickel plated bright finished mild steel piano hinges 1 mm thick
25 mm wide metre 39.00
0641 Bright finished or black enameled mild steel bolts and nuts
50x6 mm each 5.00
0642 Oxidised mild steel butt hinges 125x65x2.12 mm 10 Nos 130.00
0646 Oxidised mild steel parliamentary hinges 150x125x27x2.8 mm 10 Nos 334.00

No.

0650 Oxidised mild steel single acting spring hinges 150 mm each 138.00
0653 Oxidised mild steel double acting spring hinges 150 mm each 157.00
0656 Nickel plated mild steel piano hinges 1 mm thick 35 mm wide metre 44.00
0660 Oxidised mild steel sliding door bolt 300x16 mm each 93.00
0661 Oxidised mild steel sliding door bolt 250x16 mm each 84.00
0662 Oxidised mild steel door latch 300x20x6 mm each 49.00
0663 Oxidised mild steel door latch 250x20x6 mm each 39.00
0664 Oxidised mild steel tower bolt (barrel type) 250x10 mm each 43.00
0668 Oxidised mild steel handles 125 mm each 20.00
0679 Oxidised mild steel hasps and staples (safety type) 150 mm 10 Nos 128.00
0682 Oxidised mild steel screws 50 mm 100 Nos 76.00
0687 Anodised Aluminium butt hinges 125x75x4 mm 10 Nos 560.00
0690 Anodised Aluminium butt hinges 100x63x3.2 mm 10 Nos 270.00
0696 Anodised Aluminium sliding door bolt 300x16 mm each 147.00
0697 Anodised Aluminium sliding door bolt 250x16 mm each 128.00

No.
0698 Anodised Aluminium tower bolt (barrel type) 300x10 mm 10 Nos 580.00
0703 Anodised Aluminium handles 125 mm with plate 175 x 32 mm 10 Nos 324.00
0704 Anodised Aluminium handles 100 mm with plate 150 x 32 mm 10 Nos 275.00
0705 Anodised Aluminium handles 75mm with plate 125 x 32 mm 10 Nos 231.00
0706 Anodised Aluminium kicking plate 50 cm long 100x3.15 mm each 142.00
0713 Block board construction flush door with teak wood ply on both
faces 35 mm thick sqm 1800.00
0717 Block board construction flush door with commercial ply on both
0752 Block board construction flush door lipping 25 mm thick sqm of
door area 300.00
0753 Square vision panel in Block board construction flush door not sqm of
exceeding 0.10 sqm door area 130.00
0754 Circular vision panel in Block board construction flush door sqm of
door area 135.00
0755 Decorative type louvers in Block board construction flush door sqm of
door area 265.00
0757 Rebate cutting in block board construction flush door sqm of
door area 70.00
0759 Decorative plywood 4 mm sqm 320.00
0763 Glue kg 75.00
0834 Synthetic enamel paint in all shades except black or chocolate
shade litre 160.00
0869 Plaster of Paris kg 5.00
1003 Mild steel round bar above 12 mm dia quintal 4400.00
1008 Flats up to 10 mm in thickness quintal 4500.00
1015 Mild steel expanded metal 20x60 mm strands 3.25 mm wide
1.60 mm thick sqm 280.00

No.
1021 Hard drawn steel wire fabric 75 x 25 mm mesh of weight not

less than 7.75 kg/sqm sqm 430.00
1022 Galvanised steel bolts & nuts 6 mm dia and 25 mm long round
head with slots 10 Nos 38.00
1189 Second class teak wood in scantling 10 cudm 776.00
1190 Second class teak wood in planks 10 cudm 791.00
1199 Sal wood in scantling 10 cudm 600.00
1200 Kiln seasoned selected sheesham wood planks 10 cudm 650.00
1211 G.I. plain washer for seam bolts 100 Nos 32.00
1231 Extra for selected planks of second class teakwood 10 cudm 150.00
1238 Extra for selected planks of first class teakwood 10 cudm 150.00
2206 Carriage of Stone aggregate 40 mm nominal size and above cum 112.79
2207 Carriage of Brick tiles 1000 Nos 166.03
2406 Float glass panes of nominal thickness 4 mm (weight not less
than 10 kg/sqm) sqm 300.00
2407 Float glass panes of nominal thickness 5 mm (weight not less
than 12.50 kg/sqm) sqm 500.00
2412 Ply wood 5 ply with commercial ply on both faces 6 mm thick sqm 300.00
2413 12 mm commercial ply sqm 500.00
2414 18 mm thick block board with commercial ply veneering on
both side sqm 760.00
2449 Oxidised mild steel pull bolt lock (locking bolt) of size 85 mm x
42 mm with screws, bolts, nuts and washers complete each 60.00
2451 Brass cupboard lock 6 levers of approved quality, 40 mm size each 55.00
2455 Brass hanging type door stopper 150 mm each 75.00
2456 Hydraulic door closer bottle type M.S. body with necessary
accessories and screws complete each 673.00
2459 Anodised Aluminium hanging type door stopper each 19.00
2464 Anodised Aluminium pull bolt lock (locking bolt) of size 85 mm x
42 mm with screws, bolts, nuts and washers complete each 46.00
2465 Anodised Aluminium Casement stay 250 mm each 32.00
2466 Hollock wood in scantling 10 cudm 350.00
2468 Nickled Chromium Brass cupboard lock 40 mm size each 60.00
2480 Ply wood 5 ply with teak ply on both faces 9 mm thick sqm 850.00

No.
2481 Ply wood 5 ply with teak ply on one face and commercial ply
on another face 9 mm thick sqm 870.00
2483 Ply wood 7 ply with teak ply on one face and commercial ply
on another face 9 mm thick sqm 950.00
2484 Pre-laminated with decorative lamination on both side exterior
Grade-I MDF Board 12 mm thick confirming to IS:14587 sqm 460.00
2485 Pre-laminated with decorative lamination on both side exterior
Grade-I MDF Board 18 mm thick confirming to IS:14587 sqm 597.00
2486 Pre-laminated with decorative lamination one side and other
side balancing lamination exterior Grade-I MDF Board 25 mm
thick confirming to IS: 14587 sqm 860.00
thick confirming to IS:14587 sqm 430.00
thick confirming to IS:14587 sqm 565.00
2489 PVC edge bending tape 2.00 mm thick metre 20.00
2504 Kiln seasoning of timber cum 750.00
2505 Hollock wood in planks 10 cudm 390.00
2640 Glass panes of required thickness having 120 minutes of fire
resistance both intensity and radiation control (EW 120) and
minimum 20 minutes of insulation (EI 20) sqm 25000.00
2641 G.I U beading of 1.6 mm thick G.I sheet with ceramic tape. metre 245.00
2642 Ceramic tape 5 x20 mm size metre 410.00
3991 Galvanized iron (1.6 ± 0.2 mm) thick reinforcement for small series
casement window/door frame, sash, mullion & small series sliding
window frame metre 66.00
3992 Galvanized iron (1.6 ± 0.2 mm) thick reinforcement for big series
casement window/door frame, sash, mullion, big & small series
sliding window frame metre 71.00
casement door sash metre 97.00
sliding window / door sash metre 86.00
3995 G.I fasteners 100 x 8 mm each 14.00
4009 Mild steel tubes hot finished welded type kg 57.00
7001 Brass 100mm mortice latch and lock with 6 levers without pair
of handles each 210.00
7003 Pair of Anodised Aluminium lever handles for 100 mm mortice latch
and lock each 215.00
7009 12.5 mm thick tapered edge plain Gypsum plaster board confirming
to IS 2095 (Part- I) : 2011 sqm 155.00
7018 Joint tape roll roll 100.00
7019 Dash fastener / Chemical fastener each 14.00
7020 All drive screws (for gypsum board) 100 Nos 58.00

No.
7021 Primer (for gypsum board) litre 85.00

7023 Chromium plated brackets (curtain rods) each 7.00
7029 Galvanised wire mesh of average width of aperture 1.4 mm and
nominal dia of wire 0.63 mm sqm 250.00
7032 Frosted glass sheet of nominal thickness 4 mm (weighing not
less than 10 kg/sqm) sqm 460.00
7033 Nickel plated M.S. pipe 25 mm dia metre 76.00
7034 Nickel plated M.S. pipe 20 mm dia metre 72.00
7035 Nickel plated M.S. Brackets for curtain rod 20 mm each 7.00
7036 Nickel plated M.S - Brackets for curtain rod 25 mm each 8.00
7042 Mild steel conduit pipe (heavy type) ISI marked-20 mm dia metre 42.00
7043 Mild steel conduit pipe (heavy type) ISI marked-25 mm dia metre 54.00
7048 Rawl plug 50 mm (designation 10 nos) each 25.00
7049 Teak wood lipping of size 25x3 mm in pelmets metre 14.00
7055 Flat pressed 3 layer and graded particle board (medium density)
Grade 1 conforming to IS : 3087 - 18 mm thick sqm 480.00
7056 Aluminium tee channel (heavy duty) with rollers and stop end metre 100.00
7059 Aluminium hanging floor door stopper with twin rubber & stopper each 40.00
7060 Hydraulic door closer tubular type Aluminium section body each 560.00
7063 Oxidised M.S.casement stay (straight peg type) 300 mm not less
than 0.33 kg each 35.00
7064 Oxidised M.S.casement stay (straight peg type) 250 mm not less
7065 Oxidised M.S. casement stay (straight peg type) 200 mm not less
7137 Factory made 35 mm thick shutters with laminated veneer lumber
styles & rails as per TADS 15:1995 and panels of 12 mm thick
plain type-I, medium density flat pressed three layer, graded par-
ticle board (FPT-I) as per IS:3087 bonded with BWP type synthetic
resin adhesive, as per IS:848 sqm 1620.00
styles & rails as per TADS 15:1995 and panels of 12 mm thick
both sides prelaminated type-I, medium density flat pressed three
layer, graded particle board (FPT-I) as per IS:3087 bonded with
BWP type synthetic resin adhesive, as per IS:848 sqm 1720.00
styles & rails as per TADS 15:1995 and panels of 12 mm thick one
side prelaminated type-I, and other side balancing lamination, me-
dium density flat pressed three layer, graded particle board (FPT-I)
as per IS:3087 bonded with BWP type synthetic resin adhesive,
as per IS:848 sqm 1910.00

No.
styles & rails as per TADS 15:1995 and panels of sheet glass
using 10 kg/ sqm glass panes sqm 1620.00
styles & rails as per TADS 15:1995 and panels of galvanised wire
gauge with average width of aperture 1.4 mm in both directions
with wire of dia 0.63 mm sqm 1620.00
styles & rails as per TADS 15:1995 and panels of galvanised wire
gauge with average width of aperture 1.4 mm in both directions
with wire of dia 0.63 mm sqm 1430.00
7157 Laminated veneer lumber confirming to TADS 15:1995 manufac
tured in factory in frames of doors, windows 10 cudm 700.00
7184 Oxidised M.S. safety chain (weighing not less than 450 gms)
for door each 57.00
7269 25 mm thick particle board sqm 460.00
7271 Second class teak wood lipping 25 mm wide x 12 mm thick metre 29.00
7272 25 mm thick melamine faced prelaminated three layer particle
board sqm 900.00
7307 For flush door shutters Extra for providing teak veneering on
one side instead of commercial veneering sqm 330.00
7312 Expandable fastener with plastic sleeve and M.S. screws :
25 mm long each 10.00
7315 Expandable fastener with plastic sleeve and M.S. screws.
7349 12 mm M.S. 'U' beading metre 14.00
7366 Glass reinforced Gypsum (GRG) plaster board 12.5 mm thick
confirming to IS 2095 (Part- 3) : 1996 sqm 240.00
7367 Galvanised M.S. sheet 0.5 mm thick pressed channel section
of size 50x32 mm metre 57.00
7369 Galvanised M.S. sheet 0.50 mm thick pressed stud : 48x34x36 mm metre 71.00
7388 Dash hold fastener 12.5 mm dia, 50 mm long with 6 mm dia bolt each 11.00
7390 EPDM Gasket for uPVC window/door metre 19.00
7443 Aluminium single cleat of size 30x32x3 mm each 14.00
7444 Aluminium grip strip of size 50x12x2 mm each 11.00
7445 25 mm thick prelaminated flush door shutter both side decorative sqm 800.00
7449 Aluminium U beading kg 210.00
7451 Glass sheet (Pin headed) 4 mm thick sqm 305.00

No.
7468 Veneered particle board with commercial veneering on both sides
7477 Prelaminated particle board with one side decorative and other
side balancing lamination, flat pressed 3 layer & graded (medium
density) Grade i, Type II conforming to IS : 12823 (exterior grade)
density) Grade I, Type II conforming to IS : 12823 (exterior grade)
density) Grade I, Type II conforming to IS : 12823 (exterior grade)
7480 Prelaminated particle board with both sides decorative lamination,
flat pressed 3 layer & graded (medium density) Grade I, Type II
conforming to IS : 12823 (exterior grade) 12 mm thick sqm 575.00
7485 Oxidised M. S. hinges finished with nickel plating 50 mm
(Over all width) metre 40.00
7486 Oxidised M. S. hinges finished with nickel plating 65 mm
(Over all width) metre 52.00
7512 PTMT handle 125x34x24 mm each 24.00
7513 PTMT handle 150x34x24 mm each 24.00
7514 PTMT butt hinges 75x60x10 mm each 33.00
7515 PTMT butt hinges 100x75x10 mm each 43.00
7516 PTMT Tower bolt 152x42x18 mm each 48.00
7517 PTMT Tower bolt 202x42x18 mm each 67.00
7518 PTMT door catcher 72x42 mm each 24.00
7552 Coir veneered board 4 mm thick sqm 290.00
8001 24 mm thick Factory made shutters with style, rails and panels of
PVC extruded sections in white, grey or wooden finish sqm 1085.93
8002 30 mm thick Factory made shutters with style, rails and panels of
PVC extruded sections in white, grey or wooden finish sqm 1248.82
8003 Factory made PVC rigid foam panelled shutter i/c carriage sqm 1547.45
8004 Factory made PVC rigid foam panelled shutter as per IS : 4020
i/c carriage sqm 1547.45
8006 Factory made PVC rigid foam sheet 1 mm thick sqm 155.80
8010 48mmX40mmX1.5mm thick Factory made door frame of PVC
extruded sections in white, grey or wooden finish metre 125.79
8011 Factory made door frame PVC extruded sheet i/c carriage metre 251.58

No.
8014 Factory made door frame of size 50x47 mm with wall thickness
5 mm made of single piece extruded profile metre 298.74
8016 High Density expanded poly ethylene (EPE) Foam 1mm thick sqm 8.50
8017 Fire rated door frame made with 1.6 mm thick G.I sheet
(120 minutes fire rating) metre 1000.00
8018 Fire rated door shutter made with 1.6 mm thick G.I sheet (120
minutes fire rating) including hinges ( without glass panels) sqm 5000.00
8100 Powder coated M.S. butt hinges 100 mm X58 mmX1.9 mm 10 Nos 123.00
8101 SS ball bearing of size 100 x89x3mm each 450.00
8116 Zinc alloy (white powder coated) 3D Hinges for uPVC door each 451.00
8117 Zinc alloy (white powder coated) handles with zinc plated mild
steel multi point locking having transmission gear, cylinder with
keeps and one side key for uPVC casement door each set 2296.00
8118 Zinc alloy (white powder coated) handles along with zinc plated
mild steel multi point locking having transmission gear with keeps
for uPVC sliding window each set 1394.00
8119 Zinc alloy (white powder coated) handles with key along with zinc
plated mild steel multi point locking having transmission gear with
keeps for uPVC sliding door each set 1150.00
8121 uPVC extruded (small series) casement window frame size
47x50mm metre 258.30
8122 uPVC extruded (small series) casement window sash/window
mullion size 47x68 mm metre 282.90
8125 uPVC extruded glazing bead of appropriate dimension for small
series casement window Sash metre 98.40
8126 uPVC extruded (big series) casement window frame size 67x60 mm metre 319.80
8127 uPVC extruded (big series) casement door frame size 67x64 mm metre 360.80
8128 uPVC extruded (big series) casement window sash/window
mullion/door mullion size 67x80 mm metre 426.40
8129 uPVC extruded (big series) casement door sash size 67x110 mm metre 516.60
8130 uPVC extruded glazing bead of appropriate dimension for big
series casement window/door sash metre 123.00
8131 uPVC extruded glazing bead of appropriate dimension for small
series sliding window sash metre 60.00
8132 uPVC extruded glazing bead of appropriate dimension for big
series of sliding window/ door sash metre 85.00
8133 uPVC extruded (small series) 2 track sliding window frame
size 52x44 mm metre 285.00
8134 uPVC extruded (big series) 2 track sliding window/door frame
size 67x50mm metre 385.00
8135 uPVC extruded (small series) 3 track sliding window frame size
92x44 mm metre 380.00

No.
8136 uPVC extruded (big series) 3 track sliding window/door frame

size 116x45mm metre 530.00
8137 uPVC extruded (small series) 2 track sliding window sash/3
track sliding window sash size 32x60mm metre 265.00
8138 uPVC extruded (big series) 2 track sliding window sash size
8139 uPVC extruded (big series) 3 track sliding window sash size
8140 uPVC extruded interlock of appropriate dimension for small
series sliding window sash metre 80.00
8141 uPVC extruded interlock of appropriate dimension for big
series sliding window/ door sash metre 90.00
8142 uPVC extruded inline adaptor of appropriate dimension for big
series sliding window/door sash metre 90.00
8143 uPVC extruded 2 track sliding door sash/ 3 track sliding door
sash (big series) size 46x82mm metre 350.00
8210 Stainless steel screws 50 mm 100 Nos 270.00
8215 Stainless steel butt hinges 125x64x1.9 mm IS : 12817 marked 10 Nos 265.00
8219 Stainless steel butt hinges (heavy weight) 125x64x2.5 mm
IS :12817 marked 10 Nos 350.00
IS :12817 marked 10 Nos 255.00
IS :12817 marked 10 Nos 205.00
8222 M.S. heavy weight butt hinges 125x90x4.0 mm IS: 1341 marked. 10 Nos 210.00
8223 M.S. heavy weight butt hinges 100x75x3.5 mm IS: 1341 marked 10 Nos 160.00
8224 M.S. heavy weight butt hinges 75x60x3.1 mm IS: 1341 marked 10 Nos 95.00
8225 M.S. heavy weight butt hinges 50x40x2.5 mm IS : 1341 marked 10 Nos 80.00
8647 Stainless steel screws 30 x 4 mm 100 Nos 32.00
8678 1 mm thick 35 mm wide bright finished stainless steel piano hinges metre 42.00
8699 8 mm thick tapered edge calcium silicate board sqm 265.00
8700 10 mm thick calcium silicate board sqm 420.00
8703 Telescopic drawer channels 300 mm long set 230.00
8704 Stainless steel roller for sliding arrangement in racks/ cupboards/
cabinets shutter each 9.00

No.
8705 50 mmX42 mmX2 mm thick Factory made door frame of PVC

extruded sections in white, grey or wooden finish metre 160.00
8706 25 mm thick factory made PVC flush door shutter i/c carriage sqm 1700.00
8707 Factory made glass reinforced plastic door frame 90x45 mm i/c
carriage metre 467.00
8708 30 mm thick factory made glass fiber reinforced plastic panel door
shutter i/c carriage sqm 2326.00
8709 30 mm thick factory made solid PVC profile panelled door single
piece extruded profile decorative finish (wood grain printed on
both side) sqm 2100.00
8710 Factory made solid PVC door frame 60 x 30 mm i/c carriage metre 315.00
8711 20 mm factory made solid PVC panel door shutter i/c carriage sqm 2050.00
8712 30 mm thick factory made solid PVC profile panelled door single
piece extruded profile non decorative finish sqm 2000.00
8713 Fiber glass reinforced plastic chajja sqm 3000.00
8714 Magnetic catcher triple strip vertical type each 24.00
8715 Magnetic catcher double strip horizontal type each 18.00
8716 100 mm mortice lock with 6 levers for aluminium door each 375.00
8719 2nd class teak wood moulded beading or Taj beading/ornamental
bleading of size 18X5 mm metre 28.00
8720 Ceiling sections 0.55 mm thick having a knurled web of 51.55 mm
and two flanges of 26 mm each with lips of 10.55 mm metre 35.00
8721 Perimeter channel having one flange of 20 mm and another flange
of 30 mm with thickness of 0.55 mm and web of length 27 mm metre 22.00
8722 Nylon sleeves & wooden screws (40 mm) each 2.00
8723 Counter sunk ribbed head screw 25 mm 100 Nos 68.00
8724 12 mm thick marine plywood conforming to IS: 710 sqm 695.00
8725 12 mm thick fire retardant plywood conforming to IS: 5509 sqm 850.00
8726 1.5 mm thick decorative laminated sheet sqm 365.00
8727 1.0 mm thick decorative laminated sheet sqm 280.00
8730 30 mm thick factory made glass fiber reinforced plastic flush door
shutter i/c carriage sqm 2675.00
8734 P.V.C. Single piece extruded door frame of profile size 50 mm x
47mm with wall thickness of 5 mm metre 255.00
8735 35 mm thick factory made solid panel PVC door shutter of single
piece extruded profile non decorative finished (Matt finished) sqm 2150.00
8736 35 mm thick factory made solid panel PVC door shutter of single
piece extruded profile decorative finished (wood grain finished) sqm 2600.00
8737 Stainless steel wire guage (Grade-304) aperture 1.4 mm and
0.50mm dia wire sqm 400.00

No.
8738 Factory made door frame fire rated (60 minutes) made with 16
SWG G.I. Sheet of section 143 mm x 57 mm duly filled with
vermuculite based concrete mix metre 1050.00
8739 Fire rated door shuttere made with 16 SWG G.I. sheet (60 minutes)
without panel sqm 4500.00
8740 Fire seal Putty kg 295.00
8741 Clear fire resistant glass panes 6mm thick (60 minutes) sqm 21500.00
8742 G.I. U beading of 16 SWG G.I. sheet (zinc coating >120gm/ m²)
with ceramic tape of suitable thickness and fire resistant primer
coating metre 295.00
8743 Matrix Mineral Board metre 68.00
8744 Panic Bar / latch (Double point) each 5200.00
8745 65 mm x 55 mm x 2 mm thick Factory made door frame of PVC
extruded section in white, grey or wooden finish metre 355.00
8746 37 mm thick Factory made shutter with style,rails and panels of
PVC extruded section in white or grey finish i/c carriage sqm 2400.00
8747 75 mm x 53 mm x 2.0 mm thick Factory made door frame of PVC
extruded section in white, grey or wooden finish metre 400.00
8748 37 mm thick Factory made fusion welded shutter with style,
rails and panels of PVC extruded section in wooden finish sqm 2600.00
8749 Zinc alloy (white powder coated) touch lock with hook for wire
mesh shutter each 120.00
8750 Zinc alloy (white powder coated) casement handle for uPVC
window/door each 130.00
8751 Zinc alloy (white powder coated) touch lock withhook for uPVC
window/door each 105.00
8752 Zinc alloy body with single nylon roller (weight bearing capacity
to be 40 Kg) for uPVC sliding window each 56.00
8753 Stainless Steel (SS - 304) with adjustable double nylon roller
(weight bearing capacity to be 120 Kg) for uPVC sliding door/
window each 95.00
8754 Zinc alloy (white powder coated) cresent lock for uPVC sliding
door/window each 115.00
8755 Stainless steel friction hinge of size 200 mm x 19 x 1.9 mm for
uPVC windows each 205.00
8756 Stainless steel friction hinge of size 250 mm x 19 x 1.9 mm for
uPVC windows each 230.00
8757 Stainless steel friction hinges (SS-304 grade) size 300 x 19 x
1.9 mm for uPVC window each 245.00

No.
8760 Glass panes of required thickness having 60 minutes of fire resistance
both integrity and radiation control (EW 60) and minimum 20 minutes
of insulation (EI 20) sqm 22500.00
8772 Aluminium Track on bottom rail for uPVC window metre 30.00
8773 Wool pile/ weather pile strip for uPVC sliding window metre 20.00
8774 Aluminium Grill as per IS 1868 kg 260.00
8775 Steel Galvanised tubular reinforcement for uPVC door/ window metre 60.00
8776 Stainless steel dash fastener of 8 mm dia and 75 mm long bolt each 15.00
8777 GI Fastener 100x8 mm each 15.00
9988 Carriage and sundries L.S. 2.00

Manual For CPWD

Uploaded by

Copyright:

Available Formats

Manual For CPWD

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual For CPWD

Uploaded by

Copyright:

Available Formats

SUB HEAD : 5.

SUB HEAD -5.0 REINFORCED CEMENT CONCRETE 91

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 92

2273 Carriage of A.C.sheet and accessories tonne 92.24

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 93

7329 Single clip each 59.00

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 94

Code Description Unit Rate

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 95

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 96

5.10.3 20 mm dia. & 150 mm length each set 166.25

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 97

5.18 Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 98

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 101

5.42 Providing and fixing parallel threaded couplers conforming to IS code on

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 102

exposed aluminum surfaces mechanically snap locking the multicellular

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 103

grade using Ordinary Portland Cement (conforming to strength

SUB HEAD : 5.0 REINFORCED CEMENT CONCRETE 104

0037 Mobile crane day 7500.00

0100 Bandhani day 617.00

0101 Bhisti day 617.00

0112 Carpenter 2nd class day 679.00

0114 Beldar day 558.00

0115 Coolie day 558.00

0123 Mason (brick layer) 1st class day 738.00

0124 Mason (brick layer) 2nd class day 679.00

0155 Mason (average) day 709.00

0322 Bitumen felt :Type 3 grade 1 sqm 70.00

0357 Polymer modified adhesive mortar kg 15.00

1008 Flats up to 10 mm in thickness quintal 4500.00

1034 Bolts and nuts up to 300 mm in length quintal 4800.00

1197 Second class kail wood in scantling 10 cudm 260.00

1225 Mild steel flat strap fitting quintal 4120.00

1235 Diesel litre 73.50

2201 Carriage of Bricks 1000 Nos 276.72

2204 Carriage of Timber cum 118.59

2205 Carriage of Steel tonne 92.24

2207 Carriage of Brick tiles 1000 Nos 166.03

2208 Carriage of Lime cum 103.77

2302 Carriage of G.I. sheet and accessories tonne 92.24

SUB HEAD : 6.0 MASONRY WORK 106

7901 Machine moulded perforated common burnt clay FPS

7902 Machine moulded common burnt clay modular perforated bricks

7904 Machine moulded common burnt clay tile bricks of class

8655 Autoclaved aerated cement (AAC) blocks cum 2600.00

8656 Gypsum panel 666 X 500 X 100 mm size sqm 480.00

8657 Bonding plaster for Gypsum panel kg 25.00

9999 Sundries L.S. 2.00

SUB HEAD : 6.0 MASONRY WORK 107

Code Description Unit Rate

SUB HEAD : 6.0 MASONRY WORK 108

SUB HEAD : 6.0 MASONRY WORK 109

SUB HEAD : 6.0 MASONRY WORK 110

SUB HEAD : 6.0 MASONRY WORK 111

SUB HEAD : 6.0 MASONRY WORK 112