Specification No. 1 United Kingdom Civil Aviation Authority: Issue: 6 Date: 12 March 2004
Specification No. 1 United Kingdom Civil Aviation Authority: Issue: 6 Date: 12 March 2004
Specification No. 1 United Kingdom Civil Aviation Authority: Issue: 6 Date: 12 March 2004
United Kingdom
Specification No. 1 Civil Aviation Authority
Issue: 6
Safety Belts
1 Introduction
1.1 Although this Specification was written originally for aeroplanes, a safety belt designed
to this Specification is also acceptable to the CAA for use in a Rotorcraft.
2 Applicability
2.1 Safety belts shall comply with this Specification or with such other Specifications as the
CAA may approve. Alternative Specifications, submitted for approval, shall provide at
least the same amount of protection. FAA TSO C.22(f) is considered to be an acceptable
specification provided that compliance with paragraphs 3.8, 4.2, 5.3, 5.4, 5.5 and 5.6 of
this Specification is also demonstrated.
2.2 FAA TSO-C22g or JTSO-C22g qualified safety belts are considered acceptable for
installation with no further consideration of the requirements of this Specification.
2.3 The installation of safety belts shall be done in accordance with the certification
requirements for the aircraft.
3 Form
3.1 The belts shall be individual to a single occupant and shall be suitable in every respect
for installation in an aeroplane for the purpose of restraining the wearer, without causing
significant injury, against the ultimate inertia forces prescribed.
3.2 The correct method of using the belt shall be rapid and obvious.
3.3 Parts made of metal or similar unyielding material, which come into contact with the
wearer, shall be well rounded where necessary.
NOTE: Consideration should be given to the fact that the wearer does not remain in the normal
sitting position during the application of the higher accelerations.
3.4 No part of a safety belt shall pass between the wearer’s legs or shall appreciably restrict
the movement of the wearer’s limbs.
3.5 The belt shall, when correctly adjusted to the wearer, remain in position irrespective of
variation of load.
3.6 Those parts of the belt which under the prescribed accelerations restrain, and are in
contact with the wearer, shall be not less than 50mm (2 in.) wide.
NOTE: However for belts not needing TSO approval an approved military belt 44mm (1.75 in)
minimum width which is otherwise acceptable will not be rejected by the CAA.
The latest version of this document is available in electronic format at www.caa.co.uk, where you may also register
for e-mail notification of amendments.
Printed copy is available from: TSO, PO Box 29, Norwich NR3 1GN www.tso.co.uk/bookshop
Telephone: 0870 600 5522 e-mail: book.orders@tso.co.uk Fax orders: 0870 600 5533
3.7 Those parts defined in paragraph 3.6 shall be such that the whole of the minimum width
specified is effective in transmitting load from the parts to the wearer.
3.8 When correctly installed, the belt, when worn, shall lie across the groins of the wearer.
The belt when so worn shall lie in a plane which is approximately at 45º to the plane of
the longitudinal and lateral axes of the aeroplane.
3.9 Throughout this Specification, a belt is regarded as being divisible into various members
(e.g. left strap, right strap, release mechanism, etc.) which are liable to be detached
from each other for purposes of storage or replacement. It is further envisaged that
more than one firm may be concerned in the manufacture of the completed belt; for
example, a release box may be made by a different firm from that responsible for the
webbing parts.
4 Strength
4.1 The certified strength of a belt is determined by the tests of paragraph 7.
NOTES: 1) The certified strength required of each member will depend upon the manner
in which the belt is installed in the aeroplane and upon the emergency alighting
accelerations appropriate to the particular aeroplane.
4.2 The strength of belts with self-aligning end fittings, fitted in a normal forward-facing
installation, however, may be designed for the loads prescribed in paragraph 4.3. The
loads of paragraph 4.3 may not be used and the installation shall be conservatively
represented in the tests as required by paragraph 7 if:
a) When restraining an occupant, the vertical projection of the angle between any
strap (at its attachment point) and the fore and aft axis of the aircraft exceeds 15°,
or, if the end fittings are not self-aligning,
or
b) The installation is not a forward facing seat installation.
4.3 For unit value of forward g the basis of certified strength required of a member is 670
N/g (150 lbf/g), this load shall be multiplied by the prescribed forward g for the aeroplane
type. Safety belt attachment fittings shall have an additional strength factor of 1.33.
NOTE: Instructions may be marked on the belt to facilitate its use. However, the action should
not be such as to demand instructions.
5.3 The wearer, shall be able to release the belt with either hand, regardless of aircraft
orientation in an otherwise survivable accident without undue difficulty.
5.4 The force required to effect release from the belt shall be assessed when, after the belt
has been subjected to a load as near as practical to the ultimate load (see para. 7.2.2), it
is under a residual load of 1112 N (250 lbf).
5.4.1 Where a conventional lever operated release mechanism is used (i.e. one which can be
grasped with all the fingers of one hand) the load to effect release under the conditions
defined in para. 5.4 shall not exceed 9O N (20 lbf).
NOTE: In addition to the requirements of 5.4.2 it is also recommended that the minimum
release load should not be less than 22.5 N (5 lbf).
5.4.2 To avoid inadvertent release there shall be a free movement of the lever and the belt
shall remain fastened until the lever attains an angle of not less than 70° or not more
than 95° to its position at rest. The lever shall be spring loaded to the position it normally
assumes when the belt is fastened.
NOTE: Release at a lever angle of less than 70º may be acceptable where the design is such
that it can be demonstrated that the lever is unlikely to be caught and moved by
clothing.
5.5 Where means of release other than by a conventional lever are employed the functional
characteristics and release loads of such means shall be agreed with the CAA.
5.6 Where the positive locking action of the buckle is dependent upon a spring element, no
single failure shall cause or permit the belt to release, unless an adequate fatigue life
has been established.
5.7 The means of fastening shall be such that the responsible crew member will be able to
see at a glance whether the belt is securely fastened or not.
5.8 Extension pieces shall be identified as to the type of belt with which they are to be used.
Extension pieces shall be designed and tested to the same standards as are established
for belts submitted in compliance with this Specification.
1. British Standards Specifications issued by the British Standards Institution and D.T.D. Specifications
obtainable from HMSO are approved. Other specifications will be approved by the CAA if, in its opinion,
materials accepted as complying with these Specifications have the essential properties assumed in the
technical investigation associated with the design approval.
6.3 Materials which may deteriorate in service or materials the properties of which may be
significantly affected by ambient conditions (e.g. leather) shall not be used.
6.4 Where such processes as soldering, brazing, welding and casting are used, suitable
factors and safeguards acceptable to the CAA shall be employed. Primary load carrying
castings shall comply with the requirements for critical castings.
6.5 The choice of materials and of protective treatments for those parts which cannot
readily be inspected shall be such as to minimise the risk of corrosion or deterioration.
6.6 Materials shall be flame resistant to the appropriate standard defined in the certification
basis of the aircraft.
7 Tests
7.1 General Each member shall be tested in a manner which is agreed by the CAA to
represent adequately the conditions of the installation. Accurate representation may be
necessary for cases where unusual geometry or eccentricity of loading could affect the
ultimate load or the functioning of the means of release. Tests shall be arranged so that
the friction effects in the test apparatus do not significantly relieve the stress in any
member under test. The load in a member shall be taken as the load applied to the end
nearest to the point of attachment to the airframe or seat.
7.2 Prototype Belts
7.2.1 Each member shall be tested to the ultimate load: the member will be accepted if each
part supports the load required of it without significant slipping of any adjusting
mechanisms it may include.
NOTE: If, at the point during this test when one half of the certified strength is reached, an
inspection is made of those members utilising webbing or similar material in a load-
bearing capacity, it may be possible to obtain some confirmation whether or not it will
be possible to carry out the production test of 7.3.2.1 without damage to otherwise
satisfactory series belts.
7.2.1.1 The load to be applied shall be that of paragraph 4.3 multiplied by a factor of 1.2. where
significantly new designs are being tested the CAA may require more than one speci-
men to be tested.
7.2.2 Compliance with the requirements of paragraph 5.4 shall be demonstrated by tests in
which the release mechanism is first loaded by means of the members normally
assembled to it, to as near as is practical to the ultimate load of the belt (in no case to
less than its certified strength). The load shall then be reduced to not less than that
prescribed in paragraph 5.4 and the release mechanism operated. The force required to
operate it shall be assessed and shall be such that it can be applied without difficulty by
a wearer of the belt. This test shall be made for each combination of loads liable to be
critical.
7.3 Series Belts
7.3.1 General Series belts shall be checked for consistency with that of the prototype by
means of the tests prescribed in paragraph 7.3.2.
NOTE: These tests may be modified, in consultation with the CAA, having regard to the
particular design and to the results of tests made in accordance with paragraph 7.2.
Where experience gained with the production of the particular design shows such test
to be unnecessary, the CAA may agree to waive the test requirements of paragraphs
7.3.2.1 and 7.3.2.2 provided that an adequate sample of each production batch is
tested in accordance with paragraph 7.3.2.3.
9 Marking
Each normally detachable member of a belt certified as complying with this
Specification shall be indelibly marked with:
• the manufacturer’s approved inspection mark;
• the part number and/or model number;
• the serial or batch number.