SCAN FOR INSTALLATION VIDEOS

TECHNICAL DATA
CABLE GLAND TYPE : TMC2X
INGRESS PROTECTION : IP66, NEMA 4X

INSTALLATION INSTRUCTIONS FOR

PROCESS CONTROL SYSTEM : ISO 9001
: ISO/IEC 80079-34:2011
EXPLOSIVE ATMOSPHERES CLASSIFICATION

CMP CABLE GLAND TYPE TMC2X

ATEX CERTIFICATION No : CML 18ATEX1336X
ATEX CERTIFICATION CODE : ^II 2G 1D, Ex db IIC Gb, Ex eb IIC Gb, Ex ta IIIC Da
IECEx CERTIFICATION No : IECEx CML 18.0193X
IECEx CERTIFICATION CODE : Ex db IIC Gb / Ex eb IIC Gb, Ex ta IIIC Da
cCSAus CERTIFICATION No : 2194053
cCSAus CERTIFICATION CODE : Class I Div 1 and 2 Groups A, B, C and D; Class II, Div 1 and 2, Groups E, F and G; Class III, Div 1 and 2; Enclosure Type 4X CMP TYPE TMC2X CABLE GLAND / GLAND FOR USE WITH INTERLOCKED & CORRUGATED
: Ex d IIC; Ex e II: Class I, Zone 1, AEx d IIC; AEx e II; AEx ta IIC
CONTINUOUSLY WELDED METAL CLAD (TYPE MC OR MC-HL) OR TECK ARMORED AND
INSTALLATION INSTRUCTIONS
Installation should only be performed by a competent person using the correct tools. Read all instructions before beginning installation. ARMORED & JACKETED CABLES IN ORDINARY, WET & HAZARDOUS LOCATIONS.
INSTALLATION GUIDANCE NOTES
1.
2.
In accordance with NEC requirements, glands with NPT and Metric entry threads are suitable for both Divisions and Zones.
In accordance with CEC requirements, glands with NPT threads are suitable for both Divisions and Zones. Glands with Metric threads are only suitable for Zones unless fitted with an approved Metric INCORPORATING EU DECLARATION OF CONFORMITY TO DIRECTIVE [2014/34/EU]
to NPT thread conversion adaptor.
3. For IEC and/or ATEX installations:
- All tapes/shields/foils must be removed and any twisted pairs/triples unwound to form individual conductors.
- Drain Wires: Pass sleeving/heat shrink tube over the drain, making sure it is positioned within the resin Tube/Resin Dam area. If required, shrink the tube by applying heat, then treat the drain
wire as a conductor.
4. For NEC Class 1 Div 1 and Zone 1 see article 501.15 of the NEC.
5. The interface between a cable entry device and its associated enclosure / cable entry will require additional sealing to achieve ingress protection (IP) ratings higher than IP54. The minimum protec-
tion level is IP54 for explosive gas atmospheres and IP6X for explosive dust atmospheres. Parallel threads (and tapered threads when using a non-threaded entry) require a CMP sealing washer or
integral O-ring face seal (where available) to maintain IP66, 67 and 68 (when applicable). It is the installer’s responsibility to ensure the IP rating is maintained at the interface.
6. Note: When fitted to a threaded entry, all tapered threads will automatically provide an ingress protection rating of IP68.
7. A CMP earth tag should be used when it is necessary to provide an earth bond connection. CMP earth tags have been independently tested to comply with Category B rating specified in IEC 62444
(there are no ratings stated in IEC 60079-0). Ratings are shown in the associated table. CMP earth tags slip over the cable gland or accessory entry thread from inside/outside the enclosure and must TMC2X - Corrugated & Interlocked Metal Clad
be secured with a locknut (if fitted internally). Armor (MC) or TECK90, Continuously Welded Metal
8. Metric entry threads comply with ISO 965-1 and ISO 965-3 with a 6g tolerance as required by IEC 60079-1:2014. The CMP standard metric thread pitch is 1.5mm for threads up to M75, and 2.0mm
from M90 and above. Special thread pitches between 0.7 – 2.0mm are available on all products on request. See certificate for details of other thread types. NPT threads are in accordance with ASME Clad Armor (MCHL), ACIC-HL, ACWU90-HL, RC90-HL,
B1.20.1-2013 gauging to Cl 3.2 for external threads. For details of other thread types refer to IECEx certificate. RA90-HL
9. Enclosures must be strong enough to support the cable and cable gland assembly. The enclosure surface finish must be smooth and flat to facilitate sealing with an O-ring or Entry Thread Sealing
Washer for the required IP rating.
10. Enclosure walls must be sufficiently strong enough to support the cable and cable gland assembly. Enclosure entries shall be perpendicular. Any draft angles from the casting/moulding process should
have a perpendicular flat spot machined to facilitate sealing with an O-ring or Entry Thread Sealing Washer.
11. CMP Products recommends that when using the cable gland with a through-hole, the hole must be circular, free of burrs and the diameter no larger than 0.7mm above the thread major diameter.
A suitable CMP Products locknut shall be used to secure the product. See CMP Products catalogue for locknut options
Cable Gland Selection Table
SPECIAL CONDITIONS FOR SAFE USE
1. The glands shall only be fitted to enclosures where temperatures, at the point of mounting, is below 85°C. Order Reference Cable Jacket Across Across
Entry Thread Cable Armor Diameter Approx
(NPT with RapidEx Resin) Minimum Diameter Flats Corners Nominal
2. The cable shall be effectively clamped as close as possible to the gland. Max Over Weight
3. When used for Ex e or Ex ta applications, the user shall provide a suitable interface seal between the gland and associated enclosure to maintain the level of ingress protection of the enclosure they Thread Assembly Shroud
Armor Stop Conductors Aluminum
NPT Length Armor Stop In Length
are fitted to. Aluminum Nickel Plated Brass Stainless Steel NPT Out Min Max Max Max (Ozs)
Option
4. The TMC2X cable glands comprise of a flameproof labyrinth joint having length and gap dimensions which are other than those specified in IEC 60079-1 and are not intended to be repaired. Min Max Min Max
TMC2X-050A075X TMC2X-050NB075X TMC2X-050SS075X 1/2” - 0.78 0.42 0.55 0.55 0.63 0.51
0.500 0.750 1.20 1.32 2.44 PVC06 2.29
TMC2X-075A075X TMC2X-075NB075X TMC2X-075SS075X - 3/4” 0.80 0.42 0.55 0.55 0.63 0.51
Short Circuit Ratings Symmetrical Fault Current TMC2X-075A099X TMC2X-075NB099X TMC2X-075SS099X 3/4” - 0.80 0.60 0.65 0.65 0.89 0.71
CMP Earth Tag Size 0.690 0.990 1.48 1.63 2.96 PVC09 3.00
(kA) for 1 second TMC2X-050A099X TMC2X-050NB099X TMC2X-050SS099X - 1/2” 0.78 0.60 0.78 0.78 0.89 0.51
20 3.06 TMC2X-100A118X TMC2X-100NB118X TMC2X-100SS118X 1” - 0.98 0.79 0.86 0.86 1.10 0.94
0.870 1.180 1.81 1.99 3.15 PVC11 5.11
25 4.06 TMC2X-075A118X TMC2X-075NB118X TMC2X-075SS118X - 3/4” 0.80 0.79 0.98 0.98 1.10 0.71
32 5.40 TMC2X-125A137X TMC2X-125NB137X TMC2X-125SS137X 1-1/4” - 1.00 0.94 1.08 1.08 1.28 1.20
1.020 1.370 2.05 2.26 3.55 PVC15 6.70
40 7.20 TMC2X-100A137X TMC2X-100NB137X TMC2X-100SS137X - 1” 0.98 0.94 1.18 1.18 1.28 0.94
50 10.40 TMC2X-150A162X TMC2X-150NB162X TMC2X-150SS162X 1-1/2” - 1.03 1.22 1.35 1.35 1.50 1.46
1.300 1.620 2.36 2.60 3.59 PVC18 8.82
63 10.40 TMC2X-125A162X TMC2X-125NB162X TMC2X-125SS162X - 1-1/4” 1.00 1.22 1.42 1.42 1.50 1.20
75 10.40 TMC2X-150A190X TMC2X-150NB190X TMC2X-150SS190X 1-1/2” - 1.03 - - 1.51 1.72 1.46
1.570 1.900 2.56 2.82 3.59 PVC37 9.45
TMC2X-125A190X TMC2X-125NB190X TMC2X-125SS190X - 1-1/4” 1.00 - - 1.51 1.72 1.20
TMC2X-200A200X TMC2X-200NB200X TMC2X-200SS200X 2” - 1.53 1.57 1.70 1.70 1.88 1.63
1.650 2.000 2.75 3.03 3.76 PVC21 11.06
TMC2X-150A200X TMC2X-150NB200X TMC2X-150SS200X - 1-1/2” 1.03 1.57 1.70 1.70 1.88 1.46
TMC2X-250A233X TMC2X-250NB233X TMC2X-250SS233X 2-1/2” - 1.63 - - 1.81 2.21 2.13 PVC28
TMC2X-200A233X TMC2X-200NB233X TMC2X-200SS233X - 2” 1.53 - - 1.81 2.21 1.910 2.330 1.90 2.95 3.25 3.97 12.77
PVC23
TMC2X-150A233X TMC2X-150NB233X TMC2X-150SS233X - 1-1/2” 1.03 - - 1.81 2.21 1.46
TMC2X-300A272X TMC2X-300NB272X TMC2X-300SS272X 3” - 1.63 2.14 2.46 2.17 2.61 2.55 PVC31
TMC2X-250A272X TMC2X-250NB272X TMC2X-250SS272X - 2-1/2” 1.63 2.14 2.46 2.46 2.61 2.270 2.720 2.13 3.54 3.89 4.10 24.69
PVC28
TMC2X-200A272X TMC2X-200NB272X TMC2X-200SS272X - 2” 1.53 2.14 2.46 2.46 2.61 1.90
TMC2X-350A325X TMC2X-350NB325X TMC2X-350SS325X 3-1/2” - 1.68 2.49 2.78 2.78 2.97 2.98
2.620 3.250 4.33 4.76 4.67 PVC32 42.68
TMC2X-300A325X TMC2X-300NB325X TMC2X-300SS325X - 3” 1.63 2.49 2.78 2.78 2.97 2.98
TMC2X-400A376X TMC2X-400NB376X TMC2X-400SS376X 4” - 1.73 2.95 3.45 3.45 3.54 3.38
CMP Products Limited on its sole responsibility declares that the equpement referred to herein conforms to the requirements of the ATEX Directive 2014/34/EU and the following standards: 3.160 3.760 4.84 5.32 4.95 LSF33 53.44
TMC2X-350A376X TMC2X-350NB376X TMC2X-350SS376X - 3-1/2” 1.68 2.95 3.45 3.45 3.54 3.38
TMC2X-400A425X TMC2X-400NB425X TMC2X-400SS425X 4” - 1.73 - - 3.56 3.94 3.700 4.250 3.38 5.23 5.75 5.16 LSF34 59.19
EN 60079-0:2018, EN 60079-1:2014, EN 60079-7:2015, EN 60079-31:2014, BS 6121:1989, EN 62444:2013
*Order Code Example: TMC2X-050A075 - “TMC2X” (Gland Type) - “050” (1/2” NPT Thread) - “A” (Material Aluminum) - “075” (Max Cable Diameter 0.75”)

Dimensions are displayed in inches unless otherwise stated

David Willcock - Certification Engineer (Authorised Person)

CMP Products Limited, Cramlington, NE23 1WH, UK FI401
15 April 2019
Certificate Revision Date
Glasshouse Street • St. Peters • Newcastle upon Tyne • NE6 1BS

2776
Tel: +44 191 265 7411 • Fax: +44 1670 715 646 IFS 15 05/19
E-Mail: [email protected] • Web: www.cmp-products.com ATEX / IECEx 8 04/19

www.cmp-products.com
INSTALLATION INSTRUCTIONS FOR CMP TMC2X 3. Electrical tape MUST be wrapped around the tips of the cable cores.
This is to ensure the cable cores are together and also to cover any sharp edges
that could potentially tear the Resin Dam during installation.
1. RapidEx Resin 4 5 6 7 8 9
2. Resin Tube
3. Entry Component
4. Sealant Tape or Inner Jacket
5. Resin Dam
6. End Stop
7. Grounding Spring
8. Jacket Seal
9. Outer Nut 4. Pass the cable through the gland until the armor makes contact with the end stop. If it is not possible for the insulated con-
1 2 3
ductors to pass through the end stop then it should be removed so that the armor can make contact with the integral end stop
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE BEGINNING THE INSTALLATION within the entry component. At this stage unscrew the Outer Nut and slide it back over the cable, enough to have access to the
Armor Spacer. If no access is gained repeat step 2 and trim the outer jacket up to “L” plus 10%. Assemble the gland.
1. Cable preparation — Without Inner Jacket
Strip back the jacket armor to suit the equipment geometry.
Hand tighten the Outer Nut to compress the
Outer Jacket
Grounding Spring to secure the armor. Do not over
Tape 2. tighten the Outer Nut. Remove electrical tape from
Cable Fillers Cut Tape to Length cable core tips. Separate the cable cores slightly to
Length = groove in hexagon to front of Outer Nut allow resin to flow between them. When insulating
Cable Cores
grounding conductors are present, spread the
3. strands slightly to allow the resin to form a full seal.
After the tape has been applied, cut
---
---

the cable fillers to the edge of the tape. Refer to ‘RapidEx’ assembly instructions to fill
Using the measure guide, wrap electrical tape around the the gland resin tube with the required amount
fillers and cores of the cables to the required length Note: For instrumentation cables utilizing shielded cable, individual/ of RapidEx.
overall drain wires, see Installation Guidance Notes overleaf.
1.

1. Cable preparation — With Inner Jacket 5. Once the resin has cured, loosen the Outer Nut to ensure that the Grounding Spring is not gripping the cable. Slide the Outer
Strip back the jacket armor to suit the equipment geometry. Nut back over the cable, enough to loosen the Armor Spacer from the Entry Component. Screw the Entry Component into the
Cut Inner Jacket to Length enclosure. Retighten the Armor Spacer when the entry component is fully tightened into the enclosure.
Length = groove in hexagon to front of Outer Nut

Using the measure guide, cut the cable inner jacket

(and any cable fillers) to the required length. If inner
---
---

jacket is too large for the Resin Dam, cut off and
replace with electrical tape.

2. Using the armor measure guide, expose the armor further by stripping back the cable jacket
Cut Outer Jacket to Length 6. Finally, holding the cable central in the gland, tighten the Outer Nut to compress the Grounding Spring to secure the armor
Length = Groove in hexagon to rear of Outer Nut and the seal to engage the cable jacket. Do not over tighten the Outer Nut. The Entry Component and Outer Nut do not have to
close face to face.

NOTE: When the outer jacket is at its

maximum, cut distance may have to be
---
---

increased by up to 10%.

www.cmp-products.com www.cmp-products.com