Table of Contents

Safety Precautions…………….……….…………..…………..2
About VAG401………….………..……………………………..4
1. Applications……………….……….……………………….…..4
2. Available Functions…………….…..…………….……………4
3. Supported Systems……………………………….…………..4
4. Professional function.………………………………………...4
5. Main features…………………………………….……………5
6. Appearance and Key Descriptions …………………………5
Operation Instructions……………….....……………………..6
1. Preparation for Testing…………….………….……………..6
2. Connect the VAG401….……………….…………………….7
3. Diagnosis system…………………..…..…………...…………8
3.1 READ ECU version…………………….…….….……......10
3.2 Read Fault codes.………..……………………..…….10
3.3 ERASE Fault…….…………………….……………….11
3.4 Read measuring data value……………………..……11
3.5 Output test.…………………………………..……….…12
3.6 Basic items setting……………………………..………13
3.7 Route adaptation…………….…….…………………..13
3.8 Coding……………………..….……………………….…13
3.9 Login the system……………………………………..14
3.10 Advanced ID ……………………...………….……….15
3.11 System being ready…………………………………..16
3.12 Professional function…………………………………16
4. Language select…………………………………………….. 18
5. Contrast value adaptation………………………………..….18
6. Lcd test…………………..………………………………...… 19
7. Key testing…………………………………………………….19
8. About…………………………………………………………..20
9. Location of Data Linking Connection……………………….21
VAG401 VW/AUDI/SEAT/SKODA

Safety Precautions
To avoid personal injury, instrument damage and/or damage to your
vehicle; do not use the VAG401 before reading this manual.

This manual describes common test procedures used by experienced

service technicians. Many test procedures require precautions to avoid
accidents that can result in personal injury, and/or damage to your vehicle
or test equipment. Always read your vehicle's service manual and follow its
safety precautions before and during any test or service procedure.
ALWAYS observe the following general safety precautions:

When an engine is running, it produces carbon monoxide, a toxic and
poisonous gas. To prevent serious injury or death from carbon
monoxide poisoning, operate the vehicle ONLY in a well-ventilated
area.

To protect your eyes from propelled objects as well as hot or caustic
liquids, always wear approved safety eye protection.

When an engine is running, many parts (such as the coolant fan,
pulleys, fan belt etc.) turn at high speed. To avoid serious injury,
always be aware of moving parts. Keep a safe distance from these
parts as well as other potentially moving objects.

Engine parts become very hot when the engine is running. To prevent
severe burns, avoid contact with hot engine parts.

Before starting an engine for testing or trouble-shooting, make sure
the parking brake is engaged. Put the transmission in park (for
automatic transmission) or neutral (for manual transmission). Block the
drive wheels with suitable blocks.

Connecting or disconnecting test equipment when the ignition is ON
can damage test equipment and the vehicle's electronic components.
Turn the ignition OFF before connecting the VAG501 to or
disconnecting the VAG401 from the vehicle’s Data Link Connector
(DLC).

To prevent damage to the on-board computer when taking vehicle
electrical measurements, always use a digital multimeter with at least
10meg Ohms of impedance.

Fuel and battery vapors are highly flammable. To prevent an explosion,

2 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

keep all sparks, heated items and open flames away from the battery
and fuel / fuel vapors. DO NOT SMOKE NEAR THE VEHICLE
DUR-ING TESTING.

Don't wear loose clothing or jewelry when working on an engine.
Loose clothing can become caught in the fan, pulleys, belts, etc.
Jewelry is highly conductive, and can cause a severe burn if it makes
contact between a power source and ground.

3 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

1
About VAG401
1. Applications
VAG401 is the higher version based on VAG5053 with powerful
function. It can work on VW, AUDI, SEAT and SKODA. With its smart
appearance and powerful function, it can be conveniently used and
can be run detachedly without PC.
2. Available Functions

Controller Info

Fault Codes

Clear Codes

Measure Blocks

Output Tests

Basic Settings

Adaptation

Coding

Security Access

Readiness

Advanced ID
3. Supported Systems
VAG401 can support the following systems:

Engine

Auto Trans

ABS Brakes

Auto HVAC

Cent. Elect.

Airbags

Steering wheel

Instruments
With other systems totally over tens here not listed one by one.
4. Professional function.

Oil Reset

Srs Reset

Throttle Adaption

Mileage Reset

EEPROM Access
4 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

5. Main features

Display: Backlit LCD,160*160 pixel display.

Favorable----about only 10% of that of professional tool.

Powerful function-----with all the function of VAG1551/1552.

Conveniently connection and simply operation.

Powered via diagnostic connector, no need of power exteriorly
charged.

Operating Temperature: -20℃ to 50℃ .

Storage Temperature: -50℃ to70℃ .
6. Appearance and Key Descriptions

The appearance of a VAG401 is as shown in the above figure.

1. LCD screen: 160*160
2. Enter key: confirm selection and enter
3. Esc key: go back to the previous screens
4. up/down arrows: moves the selection pointer and scrolls up or down
5. LEFT/RIGHT arrows: move cursor.
6. Diagnostic extension cable: OBDII -16PIN
5 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

Operation Instructions
1. Preparation for Testing
The VAG401 aids in monitoring electronic and emissions-related faults in
your vehicle and retrieving fault codes related to malfunctions in these
systems. Mechanical problems such as low oil level or damaged hoses,
wiring or electrical connectors can cause poor engine performance and
may also cause a “false” fault code. Fix any known mechanical problems
before performing any test. See your vehicle’s service manual or a
mechanic for more information.

Check the following areas before starting any test:

Check the engine oil, power steering fluid, transmission fluid (if
applicable), engine coolant and other fluids for proper levels. Top off
low fluid levels if needed.

Make sure the air filter is clean and in good condition. Make sure all
air filter ducts are properly connected. Check the air filter ducts for
holes, rips or cracks.

Make sure all engine belts are in good condition. Check for cracked,
torn, brittle, loose or missing belts.

Make sure mechanical linkages to engine sensors (throttle, gearshift
position, transmission, etc.) are secure and properly connected. See
your vehicle’s service manual for locations.

Check all rubber hoses (radiator) and steel hoses (vacuum/fuel) for
leaks, cracks, blockage or other damage. Make sure all hoses are
routed and connected properly.

Make sure all spark plugs are clean and in good condition. Check for
damaged, loose, disconnected or missing spark plug wires.

Make sure the battery terminals are clean and tight. Check for
corrosion or broken connections. Check for proper battery and
charging system voltages.

Check all electrical wiring and harnesses for proper connection. Make
sure wire insulation is in good condition, and there are no bare wires.

Make sure the engine is mechanically sound. If needed, perform a
compression check, engine vacuum check, timing check (if
applicable), etc.
6 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

2. Connect the VAG401

2.1 Turn the ignition on.
2.2 Locate the vehicle's 16-pin Data Link Connector (DLC).
2.3 Connect the VAG401 cable connector to the vehicle’s DLC. Turn on
the ignition, The VAG401 will auto start, the following screen will be
displayed.

2.4 Wait a moment, the screen will auto display the main menu:

[Diagnose]: diagnose

[Language]: language select

[Contrast]: Contrast adaptation

[Display Test]: Lcd test

[Keypad Test]:Keypad test

[Information]:show version

7 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

3. Diagnosis system
Select [Diagnosis system] and then press [enter] key. The screen will
display the system selection menu as follow:

Now we can select a version, then press [Enter]. The screen will display as
the following shows.

Systems that the VAG401 supports are listed as the following 7 ones. Each
system in the 7 kinds comes with similar operation method. Press
[Common], then press [Enter].The screen will show the systems most cars
shares. See the following.

8 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

Now we can select any one system, say, selecting [17-Instruments], then
press [Enter]. The screen will display as the following shows.

If it runs successfully, then the following will be displayed.

Press [Enter] button or [Esc] button.

9 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

If failed, then it displays the following.

3. 1 READ ECU version

Select [01.READ ECU version] and then press [Enter] key. The screen will
display the control unit information:

3.2 Read Fault Codes

Select [02-Fault Codes] and then press [Enter] key. The screen will show
the error code and you can press up or down key to check out each error
code as the following.

10 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

3.3 Erase fault codes

Select [05-Clear Codes] and then press [Enter] as the following.

You need to press [Enter] button for the second time to perform “code
erase”. Of course you can also press [Esc] button to give u. If code erasing
successfully, it will display as the following.

3.4 Read measuring data value

Select [08-Measure Blocks] and then press Enter as the following.

11 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

Press the left / right to choose the number of places, by up / down button to
select the input number and press [Enter] button to confirm. Figure shows
that:

3.5 Output test.

Select [03-Output Test] and then press [Enter]. If failed, it will display as the
following.

If succeeded, it will display as the following.

12 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

3.6 Basic items setting.

Select [04-Basic Settings] and then press [Enter]. The way of operating
likes that of point 3.4 regarding of measuring data value.

3.7 Route adaptation

Select [10-Adaptation] and then press [Enter]. The way of operating likes
that of point 3.4 regarding of measuring data value.

3.8 Coding
Select [07-Coding] and then press [Enter].It will display as the following.

13 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

Press Left or Right key to choose the number of places; by Up or Down key
to input number. Press [Enter] button to confirm.

After all information written, press [Enter]. If operation is successful, it will

display as the following.

3.9 Login the system

Choose [16-Security Access] and then press [Enter] button. It shows as the
following

Press left/right button to choose number of places. Press up/down button to

enter the passing code and then press [Enter].The following will be

14 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

displayed if you login successfully.

If failed, it shows as the following.

3.10 Advanced ID
Choose [1A-Advanced ID] and then press [Enter] button. It shows as the
following.

Press [Esc] to draw out.

15 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

3.11 System being ready

Press [15-Readiness] and then press [Enter], it shows as the following.

Press [Esc] to login out.

3.12 Professional function
Return to the main memu, choose [Diagnose] and then press [Enter]. Press
right arrow to go to the next page. Choose [Special Function]. Press [Enter].
It will show the following.

3.12.1 Choose [Oil Reset] and press [Enter]. it shows as the following:

If connect successfully, it displays the following one by one.

16 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

Press [Esc] to draw out.

3.12.2 Choose [Srs Reset] and [Enter], it shows as the following.

If connected successfully, it will read code before it returns to the original; if

it finds error code, it will display the following.

Then, press [Enter] and it will force the implementation of reset command
and will display as the following after success.

17 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

If you don’t want to force the implementation of reset command, please

press [Esc] to draw out. After finishing code erasing, you can reset airbag.
4. Language select
Choose [Language] at the main memu. Then press [Enter]. The screen will
display as the following.

5. Contrast value adaptation

Choose [Contrast] at the main memu. Then press [Enter]. The screen will
display as the following.

18 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

Simply press up/down arrow to set and then press [Enter] to

confirm.
6. Lcd test
Choose[Lcd Test] at the main memu, Press Enter],The screen will display
the following dynamic image.

When after testing, it will show “Test end!” as what the following shows.

7. Key testing
Choose [Keypad Test] at the main memu. Press [Enter]. The screen will
display the following interface.

19 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

Press any key then the screen will flash due to corresponding to your
cooperation. Double [Esc], you can withdraw from the testing.

8.About
Choose [About] and then press [Enter]. Then screen will display the version
of this tool.

20 www.Xtooltech.com
VAG401 VW/AUDI/SEAT/SKODA

9.Location of Data Linking Connection.

Refer to the picture of OBD-II 16pin as the following. For VW GOLF, it
locates in the right side of steering column; for Jetta, it locates in the left
side of the bottom of the dashboard which is at the driver’s ca; for Santana,
it locates the dust-proof gearbox which is in the front. For more details,
please refer to the vehicle repairing manual.

21 www.Xtooltech.com