Alloys For Extrusion

Page 1 of 2
Home Design support Showcase News Events Profile Academy Sponsors Contact
Why Aluminium? Aluminium alloys – Alloys for extrusion

Aluminium Life Cycle
Aluminium for extrusion is mostly alloys with the following serial numbers:
Properties of aluminium 1000 series – Al
Material comparison
6000 series – Al + Mg + Si
7000 series – Al + Zn + Mg
Design Showcase
The 1000 series is non heat treatable. These alloys are often chosen in products where high thermal and electrical conductivity
Submit a project are desired. They have low strength.
Architecture
The 6000 and 7000 series are heat treatable. They are the most commonly used extrusion alloys and have a wide range of
Consumer Products applications.
Furniture
The 6000 series has good extrudability and can be solution heat treated at the extrusion temperature. Furthermore, these alloys
Technology have medium to high strength, are easy to weld and offer good resistance to corrosion, even in marine environments. The bulk of
Transport the extruded material for load bearing constructions is made from these qualities. They are used for load bearing constructions
both on land and at sea.
Design support
The 6060 alloy offers medium strength and is easy to extrude even for complicated cross-sections. This alloy is the most used
Extrusion Design Guide
extrusion alloy. It has good formability during bending in the T4 condition. Typical applications are extrusions for windows and
Die design doors, lighting, awnings, handrails and furniture. This material is highly suitable for anodising, both for decorative and protective
reasons.
Aluminium Alloys
Aluminium Extrusion The 6101 alloy offers virtually the same production possibilities as 6060. It is especially suitable for electrical applications where
fairly high strength is required.
Aluminium Surface
Treatment The 6063 alloy has slightly higher strength than 6060, but is also marginally more difficult to extrude, especially if the cross-
Fabrication section is complicated. Applications are for the most part the same as for 6060. This material is well suited for anodising, both
for decorative and protective purposes.
Corrosion Resistance
Joining aluminium The 6005A alloy has higher strength than 6063 but is slightly harder to extrude. It is suitable for anodising for protective
purposes but the quality of the surface makes decorative finishing more difficult.
The 6082 alloy has high strength and is suitable for extrusion of cross-sections that are not too complicated. Typical applications
Sponsors are load carrying structures in the ship, offshore, transport, and building industries such as platforms, bridges, stairs, scaffolds
Sapa Profiles UK Ltd and handrails. The material is suitable for anodising for protective purposes.
Design and extrusion of
aluminium profiles. The 7000 series has the highest strength of the most used construction alloys. They have good weldability and obtain lower
Click to visit website. reduction of strength in heat affected zones than the 6000 series. Their corrosion resistance and formability are, however, not as
good as those in the 6000 series. But by adding small amounts of Zr, Cr or Mn this can be improved. Typical applications are
automotive parts, aircraft containers, bicycle frames and high speed boats.
The 7108 alloy has high strength and good fatigue strength, but has a limited extrudability and formability. The alloy is
susceptible to stress corrosion in areas with high stresses. The resistance to stress corrosion is slightly increased with overageing.
Welding should only be carried out in areas where the loading is lower. Typical applications are structures for building and
transport applications where high strength is required. The material is suitable for anodising for protective purposes.
10/01/2013
Page 2 of 2
The magnesium and silicon contents of various 6000 alloys can overlap in certain cases (see diagram above). Alloys can
therefore be made up with the focus on optimal function adaptation and the ability to produce them. This process takes place
continuously and today there are a number of variants of the alloy types above that have been adapted to suit specific conditions.
Temperature – Mechanical Properties

Care should be taken when using aluminium at high temperatures. Mechanical properties could significantly be reduced at
temperatures above 100°C, especially if the material has been thermally hardened or cold worked.
In general the 6060, 6063, 6005A and 6082 alloys should not be used in structures at temperatures above 100°C. The tensile
strength decreases as the temperature increases while elongation on fracturing usually increase. It should be noted that the
characteristics are dependent of alloy, temperature and time. If the designer is unfamiliar with the exact temperature
characteristics for a given alloy, it can be assumed as a starting point that properties such as tension, shear and fatigue strength
vary in proportion to the tensile strength.
Low Temperature Properties

In contrast to steel, aluminium alloys do not become brittle at low temperatures. In fact aluminium alloys increase in strength
and ductility whilst impact strength remain unchanged. As the temperature decreases, below 0°C, the yield strength and tensile
strength of aluminium alloys increase.
Alloy Summary
Special material properties can be achieved with special thermal hardening.
With, for example, extended heating, ie thermal hardening longer than the optimal hardening time, lower strength is achieved
but in return the alloy becomes tougher and in certain cases has greater resistance to corrosion.
Condition:
F – Extruded and air cooled
O – Softened, annealed at 350-500°C, for 1-5 hours
T4 – Solution heat treated and naturally aged at 20°C, for 5-10 days
T6 – Solution heat treated, artificially aged
home design support showcase news events profile academy sponsors contact
Terms & Conditions | Copyright © Sapa Profiles UK Ltd. All rights reserved 2013
10/01/2013

Alloys For Extrusion

Uploaded by

Copyright:

Available Formats

Alloys For Extrusion

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Alloys For Extrusion

Uploaded by

Copyright:

Available Formats

Page 1 of 2

Why Aluminium? Aluminium alloys – Alloys for extrusion

Temperature – Mechanical Properties

Low Temperature Properties

You might also like