CR200/CR200X Series

Dataloggers
Revision: 6/11

C o p y r i g h t © 2 0 0 0 - 2 0 1 1
C a m p b e l l S c i e n t i f i c , I n c .
Warranty and Assistance
PRODUCTS MANUFACTURED BY CAMPBELL SCIENTIFIC, INC. are
warranted by Campbell Scientific, Inc. (“Campbell”) to be free from defects in
materials and workmanship under normal use and service for twelve (12) months
from date of shipment unless otherwise specified on the corresponding Campbell
invoice. Batteries, fine-wire thermocouples, desiccant, and other consumables have
no warranty. Campbell's obligation under this warranty is limited to repairing or
replacing (at Campbell's option) defective products, which shall be the sole and
exclusive remedy under this warranty. The customer shall assume all costs of
removing, reinstalling, and shipping defective products to Campbell. Campbell will
return such products by surface carrier prepaid within the continental United States
of America. To all other locations, Campbell will return such products best way CIP
(Port of Entry) INCOTERM® 2010, prepaid. This warranty shall not apply to any
Campbell products which have been subjected to modification, misuse, neglect,
improper service, accidents of nature, or shipping damage. This warranty is in lieu
of all other warranties, expressed or implied. The warranty for installation services
performed by Campbell such as programming to customer specifications, electrical
connections to products manufactured by Campbell, and product specific training, is
part of Campbell’s product warranty. CAMPBELL EXPRESSLY DISCLAIMS
AND EXCLUDES ANY IMPLIED WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. Campbell is not liable for any
special, indirect, incidental, and/or consequential damages.

Products may not be returned without prior authorization. The following contact
information is for US and International customers residing in countries served by
Campbell Scientific, Inc. directly. Affiliate companies handle repairs for customers
within their territories. Please visit www.campbellsci.com to determine which
Campbell Scientific company serves your country.

To obtain a Returned Materials Authorization (RMA), contact Campbell Scientific,

Inc., phone (435) 753-2342. After an applications engineer determines the nature of
the problem, an RMA number will be issued. Please write this number clearly on
the outside of the shipping container. Campbell Scientific's shipping address is:

CAMPBELL SCIENTIFIC, INC.

RMA#_____
815 West 1800 North
Logan, Utah 84321-1784

For all returns, the customer must fill out a “Declaration of Hazardous Material and
Decontamination” form and comply with the requirements specified in it. The form
is available from our website at www.campbellsci.com/repair. A completed
form must be either emailed to [email protected] or faxed to 435-750-
9579. Campbell Scientific will not process any returns until we receive this form. If
the form is not received within three days of product receipt or is incomplete, the
product will be returned to the customer at the customer’s expense. Campbell
Scientific reserves the right to refuse service on products that were exposed to
contaminants that may cause health or safety concerns for our employees.
Table of Contents
Section 1. Introduction ............................................... 1
1.1 CR200(X) series Datalogger Models ..................................................................... 1

Section 2. Quickstart Tutorial .................................... 3

2.1 Primer - CR200(X) Data Acquisition..................................................................... 3
2.1.1 Components of a Data Acquisition System .............................................. 3
2.1.2 CR200(X) Mounting................................................................................. 4
2.1.3 Wiring Panel ............................................................................................. 4
2.1.4 Battery Backup ......................................................................................... 5
2.1.5 Power Supply............................................................................................ 5
2.1.6 Antenna..................................................................................................... 5
2.1.7 Analog Sensors ......................................................................................... 6
2.1.8 Bridge Sensors .......................................................................................... 6
2.1.9 Pulse Sensors ............................................................................................ 7
2.1.10 Digital I/O Ports........................................................................................ 8
2.1.11 RS-232 Sensors......................................................................................... 9
2.2 Hands-on Exercise - Measuring Temperature...................................................... 10
2.2.1 Hardware Setup....................................................................................... 11
2.2.2 Configuration .......................................................................................... 11
2.2.3 PC200W Software Setup ........................................................................ 11

Section 3. Overview .................................................. 23

3.1 CR200(X) Overview ............................................................................................ 23
3.1.1 Programmed Instructions Are Evaluated Sequentially ........................... 24
3.1.2 Sensor Support........................................................................................ 25
3.1.3 Input / Output Interface: The Wiring Panel ............................................ 25
3.1.4 Power Requirements ............................................................................... 29
3.1.5 Programming: Firmware and User Programs ......................................... 29
3.1.6 Memory and Data Storage ...................................................................... 30
3.1.7 Communications Overview .................................................................... 31
3.1.8 Maintenance Overview ........................................................................... 32
3.2 PC Support Software............................................................................................ 34
3.3 Specifications....................................................................................................... 35

Section 4. Sensor Support ....................................... 37

4.1 Powering Sensors................................................................................................. 37
4.1.1 Switched Precision.................................................................................. 37
4.1.2 Continuous Unregulated (Nominal 12 Volt)........................................... 37
4.1.3 Switched Unregulated (Nominal 12 Volt) .............................................. 38
4.2 Voltage Measurement .......................................................................................... 38
4.2.1 Measurement Sequence .......................................................................... 38
4.2.2 Measurement Accuracy .......................................................................... 38
4.2.3 Voltage Range......................................................................................... 40
4.2.4 Integration............................................................................................... 40
4.2.5 Self-Calibration....................................................................................... 41
4.3 Bridge Resistance Measurements ........................................................................ 41
4.3.1 Measurements Requiring AC Excitation ................................................ 42

i
Table of Contents

4.4 Pulse Count Measurement....................................................................................42

4.4.1 Pulse input Channels ...............................................................................43
4.4.2 Pulse Input on Digital I/O Channels C1–C2 ...........................................45
4.5 Period Averaging Measurements .........................................................................45
4.6 SDI-12 Recording ................................................................................................46
4.7 Cabling Effects on Measurements........................................................................46
4.7.1 Analog Sensor Cables .............................................................................46
4.7.2 Pulse Sensors...........................................................................................46
4.7.3 Serial Sensors..........................................................................................47

Section 5. Measurement and Control Peripherals..49

5.1 Control Output .....................................................................................................49
5.1.1 Binary Control.........................................................................................49
5.2 Other Peripherals..................................................................................................51
5.2.1 TIMs........................................................................................................51

Section 6. CR200(X) Power Supply ..........................53

6.1 Power Requirement ..............................................................................................53
6.2 Calculating Power Consumption..........................................................................53
6.3 Power Supplies.....................................................................................................53
6.3.1 Battery Connection..................................................................................53

Section 7. Grounding ................................................55

7.1 ESD Protection.....................................................................................................55
7.1.1 Lightning Protection................................................................................56
7.2 Single-Ended Measurement Reference ................................................................57

Section 8. CR200(X) Configuration ..........................59

8.1 DevConfig ............................................................................................................59
8.2 Sending the Operating System .............................................................................60
8.2.1 Sending OS with DevConfig...................................................................60
8.3 Settings.................................................................................................................62
8.3.1 Settings via DevConfig ...........................................................................62
8.3.2 Settings via CRBASIC............................................................................66
8.3.3 Settings via Terminal Emulator...............................................................66
8.3.4 Durable Settings ......................................................................................67

Section 9. Programming ...........................................69

9.1 Inserting Comments into Program........................................................................69
9.2 Sending Programs ................................................................................................69
9.3 Writing Programs .................................................................................................69
9.3.1 Short Cut Editor and Program Generator ................................................70
9.3.2 CRBASIC Editor.....................................................................................70
9.4 Numerical Formats...............................................................................................71
9.5 Structure ...............................................................................................................72
9.6 Declarations I - Single-line Declarations .............................................................73
9.6.1 Variables .................................................................................................73
9.6.2 Constants.................................................................................................76
9.6.3 Alias and Unit Declarations ....................................................................77

ii
 Table of Contents

9.7 Declarations II - Declared Sequences .................................................................. 77

9.7.1 Data Tables ............................................................................................. 77
9.7.2 Subroutines ............................................................................................. 83
9.8 Program Execution Timing .................................................................................. 83
9.9 Instructions........................................................................................................... 84
9.9.1 Measurement and Data Storage Processing ............................................ 84
9.9.2 Parameter Types ..................................................................................... 85
9.9.3 Names in Parameters .............................................................................. 85
9.9.4 Expressions in Parameters ...................................................................... 86
9.9.5 Arrays of Multipliers and Offsets ........................................................... 86
9.10 Expressions ........................................................................................................ 87
9.10.1 Floating Point Arithmetic ....................................................................... 87
9.10.2 Mathematical Operations ........................................................................ 87
9.10.3 Logical Expressions................................................................................ 88
9.11 Program Access to Data Tables.......................................................................... 90

Section 10. CRBASIC Programming Instructions .... 93

10.1 Program Declarations........................................................................................... 93
10.1.1 Variable Declarations & Modifiers......................................................... 93
10.1.2 Constant Declarations ............................................................................. 93
10.2 Data Table Declarations ..................................................................................... 94
10.2.1 Data Table Modifiers .............................................................................. 94
10.2.2 Data Storage Output Processing ............................................................. 94
10.3 Single Execution at Compile.............................................................................. 95
10.4 Program Control Instructions ............................................................................. 96
10.4.1 Common Controls................................................................................... 96
10.5 Measurement Instructions .................................................................................. 98
10.5.1 Diagnostics ............................................................................................. 98
10.5.2 Voltage.................................................................................................... 98
10.5.3 Pulse........................................................................................................ 98
10.5.4 Digital I/O............................................................................................... 99
10.5.5 SDI-12..................................................................................................... 99
10.6 Processing and Math Instructions..................................................................... 100
10.6.1 Mathematical Operators........................................................................ 100
10.6.2 Logical Operators ................................................................................. 100
10.6.3 Trigonometric Functions....................................................................... 101
10.6.4 Arithmetic Functions ............................................................................ 102
10.6.5 Spatial Processing ................................................................................. 103
10.6.6 Other Functions..................................................................................... 104
10.7 Clock Functions................................................................................................ 104
10.8 Serial Input / Output......................................................................................... 105
10.9 Peer-to-Peer PakBus Communications............................................................. 105
10.10 Data Table Access and Management............................................................. 106
10.11 SCADA ......................................................................................................... 107
10.12 Satellite Systems Programming..................................................................... 108
10.12.1 GOES.................................................................................................... 108

Section 11. Programming Resource Library........... 109

11.1 Remote Sensor Interface .................................................................................... 109
11.2 Radio Power Minimization ................................................................................ 110
11.3 Multiple Switch Closure Measurements ............................................................ 112
11.4 SDI-12 Sensor Support ...................................................................................... 112
11.4.1 SDI-12 Command Basics...................................................................... 112
11.4.2 SDI-12 Communications ...................................................................... 116

iii
Table of Contents

11.4.3 SDI-12 Power Considerations...............................................................118

11.5 Wind Vector .....................................................................................................120
11.5.1 OutputOpt Parameters...........................................................................120
11.5.2 Wind Vector Processing........................................................................120
11.6 TrigVar and DisableVar - Controlling Data Output and Output Processing ....125
11.7 Multiple Data Intervals in Data Tables.............................................................126

Section 12. Memory and Data Storage ....................129

12.1 Data Storage .....................................................................................................129
12.1.1 Data Table Storage................................................................................129
12.2 Memory Conservation ......................................................................................130
12.3 Memory Reset ..................................................................................................130
12.3.1 Full Memory Reset................................................................................130
12.3.2 Program Send Reset ..............................................................................130
12.3.3 Manual Data Table Reset ......................................................................130

Section 13. Telecommunications and Data

Retrieval..................................................................131
13.1 Hardware and Carrier Signal ............................................................................131
13.2 Protocols ...........................................................................................................132
13.3 Initiating Telecommunications .........................................................................132
13.4 Data Retrieval...................................................................................................132
13.4.1 Via Telecommunications ......................................................................132
13.4.2 Data Format on Computer.....................................................................132

Section 14. PakBus Overview ..................................133

14.1 PakBus Addresses ............................................................................................133
14.2 Nodes: Leaf Nodes and Routers .......................................................................133
14.3 Router and Leaf Node Configuration ...............................................................134
14.4 Linking Nodes: Neighbor Discovery................................................................134
14.4.1 Hello-message (two-way exchange) .....................................................135
14.4.2 Beacon (one-way broadcast) .................................................................135
14.4.3 Hello-request (one-way broadcast) .......................................................135
14.4.4 Neighbor Lists.......................................................................................135
14.4.5 Adjusting Links.....................................................................................135
14.4.6 Maintaining Links .................................................................................136
14.5 Troubleshooting................................................................................................136
14.5.1 Link Integrity ........................................................................................136
14.5.2 Ping .......................................................................................................137
14.5.3 Traffic Flow ..........................................................................................138
14.6 LoggerNet Device Map Configuration .............................................................138

Section 15. Alternate Telecoms Resource Library ...139

15.1 Modbus.............................................................................................................139
15.1.1 Overview...............................................................................................139
15.1.2 Terminology..........................................................................................139
15.1.3 Programming for Modbus .....................................................................140
15.1.4 Troubleshooting ....................................................................................142

iv
 Table of Contents

Section 16. Support Software .................................. 143

16.1 Short Cut .......................................................................................................... 143
16.2 PC200W ........................................................................................................... 143
16.3 Visual Weather................................................................................................. 143
16.4 PC400............................................................................................................... 144
16.5 RTDAQ ............................................................................................................ 144
16.6 LoggerNet Suite ............................................................................................... 144
16.7 PDA Software .................................................................................................. 145
16.8 Network Planner............................................................................................... 145

Section 17. Care and Maintenance .......................... 147

17.1 Temperature Range .......................................................................................... 147
17.2 Moisture Protection .......................................................................................... 147
17.3 Enclosures ........................................................................................................ 147
17.4 Replacing the Internal Battery.......................................................................... 148

Section 18. Troubleshooting .................................... 151

18.1 Programming.................................................................................................... 151
18.1.2 NAN and ±INF ..................................................................................... 153
18.2 Communications............................................................................................. 154
18.2.1 RS-232 .................................................................................................. 154
18.2.2 Communicating with Multiple PC Programs........................................ 154
18.3 Power Supply ................................................................................................... 155
18.3.1 Overview............................................................................................... 155
18.3.2 Troubleshooting at a Glance ................................................................. 155
18.3.3 Diagnosis and Fix Procedures............................................................... 156

Appendices

Appendix A. Glossary ................................................... 1

A.1 Terms ..................................................................................................................... 1
A.2 Concepts............................................................................................................... 13
A.2.1 Accuracy, Precision, and Resolution ...................................................... 13

Appendix B. Status Table and Settings .................... 15

Appendix C. Serial Port Pin Outs............................... 21

C.1 RS-232 Communications Port ............................................................................. 21
C.1.1 Pin-Out.................................................................................................... 21

Appendix D. ASCII / ANSI Table................................. 23

Appendix E. Antenna Usage and Compliance.......... 27

E.1 Use of Antenna with CR200(X)........................................................................... 27
E.2 Part 15 FCC Compliance Warning ...................................................................... 27
E.2.1 Use of Approved Antennas..................................................................... 28

v
Table of Contents

Appendix F. Sensors and Peripherals.......................29

F.1 Sensors .................................................................................................................29
F.2 Dataloggers ..........................................................................................................29
F.3 Power Supplies.....................................................................................................30
F.3.1 Batteries ..................................................................................................30
F.3.2 Primary Sources ......................................................................................30
F.4 Enclosures ............................................................................................................31
F.5 Relay Drivers .......................................................................................................31
F.6 Serial Cables, Adaptors and Switches ..................................................................31
F.7 Signal Conditioners ..............................................................................................32
F.7.1 Current Shunt Modules ...........................................................................32
F.8 Telecommunications Hardware............................................................................32
F.8.1 Network Links.........................................................................................32
F.8.2 Router and Leaf Node Hardware ............................................................33
F.8.3 Ap. Telecommunications Options...........................................................33
F.8.4 Network Links.........................................................................................33
F.9 Voltage Transient Suppressors .............................................................................34

Index ..............................................................................35

List of Figures
Figure 1: Data Acquisition System Components...........................................................3
Figure 2: CR200(X) Wiring Panel.................................................................................5
Figure 3: Analog Sensor Wired to Single-Ended Channel #1 .......................................6
Figure 4: Half Bridge Wiring -- Wind Vane Potentiometer ..........................................7
Figure 5: Pulse Input Types...........................................................................................7
Figure 6: Pulse Input Wiring -- Anememeter Switch ....................................................8
Figure 7: Control and Monitoring with Digital I/O .......................................................9
Figure 8: Location of RS-232 Port ..............................................................................10
Figure 9: Use of RS-232 when Reading RS-232 Devices ...........................................10
Figure 10: Power and RS-232 Connections.................................................................11
Figure 11: PC200W Main Window.............................................................................13
Figure 12: Short Cut Temperature Sensor Folder........................................................14
Figure 13: Short Cut Thermocoupler Wiring ..............................................................15
Figure 14: Short Cut Wiring Diagram.........................................................................15
Figure 15: Short Cut Outputs Tab ...............................................................................16
Figure 16: Short Cut Output Table Definition.............................................................17
Figure 17: Short Cut Compile Confirmation ...............................................................17
Figure 18: PC200W Connect Button...........................................................................18
Figure 19: PC200W Monitor Data Tab .......................................................................19
Figure 20: PC200W Monitor Data Tab .......................................................................19
Figure 21: PC200W Collect Data Tab.........................................................................20
Figure 22: PC200W View Data Utility .......................................................................20
Figure 23: PC200W View Data Table.........................................................................21
Figure 24: PC200W View Data Graph........................................................................21
Figure 25: Features of a Data Acquisition System ......................................................24
Figure 26: CR200(X) Wiring Panel.............................................................................31
Figure 27: Voltage Measurement Accuracy (0° to 40° C)...........................................40
Figure 28: Voltage Excitation Bridge Circuit..............................................................41
Figure 29: Switch Closure Pulse Sensor......................................................................42
Figure 30: Pulse Input Types.......................................................................................44
Figure 31: Amplitude Reduction of Pulse-Count Waveform (before and after
1 ms time constant filter)......................................................................................44

vi
 Table of Contents

Figure 32: Current Limiting Resistor in a Tipping Bucket Rain Gage Circuit............ 46
Figure 33: Control Port Current Sourcing................................................................... 50
Figure 34: Relay Driver Circuit with Relay ................................................................ 51
Figure 35: Power Switching without Relay ................................................................ 51
Figure 36: Lightning Protection Scheme..................................................................... 57
Figure 37: DevConfig Utility ...................................................................................... 60
Figure 38: DevConfig OS Download Window ........................................................... 61
Figure 39: Dialog Box Confirming OS Download...................................................... 61
Figure 40: DevConfig Settings Editor......................................................................... 62
Figure 41: Summary of CR200(X) Configuration ...................................................... 63
Figure 42: DevConfig Deployment Tab...................................................................... 64
Figure 43: DevConfig Logger Control Tab................................................................. 65
Figure 44: Entering SDI-12 Transparent Mode......................................................... 117
Figure 45: Input Sample Vectors .............................................................................. 121
Figure 46: Mean Wind Vector .................................................................................. 123
Figure 47: Standard Deviation of Direction .............................................................. 124
Figure 48: Data from TrigVar Program .................................................................... 126
Figure 49: PakBus Network Addressing. .................................................................. 134
Figure 50: Flat Map................................................................................................... 138
Figure 51: Tree Map.................................................................................................. 138
Figure 52: Enclosure ................................................................................................. 148
Figure 53: Accuracy, Precision, and Resolution .................................................. Ap. 13

List of Tables
Table 1. CR200 series Dataloggers with Built-In Radio .............................................. 2
Table 2. PC200W EZSetup Wizard Example Selections. .......................................... 12
Table 3. Internal Lithium Battery Specifications ....................................................... 34
Table 4. Current Sourcing Limits............................................................................... 38
Table 5. Formats for Entering Numbers in CRBASIC............................................... 71
Table 6. CRBASIC Program Structure ...................................................................... 72
Table 7. Predefined Constants and Reserved Words.................................................. 77
Table 8. TOA5 Environment Line ............................................................................. 78
Table 9. Typical Data Table....................................................................................... 79
Table 10. Rules for Names......................................................................................... 85
Table 11. Logical Expression Examples .................................................................... 89
Table 12. Abbreviations of Names of Data Processes................................................ 90
Table 13. Derived Trigonometric Functions ............................................................ 101
Table 14. Standard SDI-12 Command & Response Set........................................... 113
Table 15. Example Power Usage Profile for a Network of SDI-12 Probes.............. 119
Table 16. OutputOpt Options ................................................................................... 120
Table 17. CR200(X) Telecommunications Options ................................................. 131
Table 18. PakBus Link Performance Gage .............................................................. 137
Table 19. Modbus to Campbell Scientific Equivalents ............................................ 139
Table 20. CRBASIC Ports, Flags, Variables and Modbus Registers ....................... 141
Table 21. LoggerNet Products that Include the LoggerNet Server .......................... 144
Table 22. LoggerNet Clients .................................................................................... 145
Table 23. Internal Lithium Battery Specifications ................................................... 149
Table 24. Program Download Errors ....................................................................... 152
Table 25. Math Expressions and CRBASIC Results................................................ 154
Table 26. Status Table Fields and Descriptions .................................................. Ap. 16
Table 27. CR200(X) Settings .............................................................................. Ap. 18
Table 28. CR200(X) RS-232 Pin-Out ................................................................. Ap. 21
Table 29. Sensors available from Campbell Scientific........................................ Ap. 29
Table 30. Dataloggers available from Campbell Scientific................................. Ap. 30
Table 31. Batteries available from Campbell Scientific...................................... Ap. 30

vii
Table of Contents

Table 32. Primary Power Sources available from Campbell Scientific...............Ap. 30

Table 33. Enclosure available from Campbell Scientific ....................................Ap. 31
Table 34. Relay Driver available from Campbell Scientific................................Ap. 31
Table 35. Serial Cables, Adaptors and Switches available from Campbell
Scientific .......................................................................................................Ap. 31
Table 36. Current Shunt Modules available from Campbell Scientific...............Ap. 32
Table 37. Telecommunications Hardware available from Campbell Scientific ..Ap. 32
Table 38. Antennas for Spread Spectrum Radios available from Campbell
Scientific .......................................................................................................Ap. 32
Table 39. PakBus Leaf Node and Router Device Configuration.........................Ap. 33
Table 40. CR200(X) Telecommunications Options ............................................Ap. 33
Table 41. Network Links available from Campbell Scientific ............................Ap. 33
Table 42. Voltage Transient Suppressors available from Campbell Scientific ...Ap. 34

List of CRBasic Examples

CRBASIC EXAMPLE 1. Inserting Comments..........................................................69
CRBASIC EXAMPLE 2. Load binary information into a single variable .................71
CRBASIC EXAMPLE 3. Proper Program Structure .................................................73
CRBASIC EXAMPLE 4. Using a variable array in calculations ...............................75
CRBASIC EXAMPLE 5. Flag Declaration and Use..................................................76
CRBASIC EXAMPLE 6. Using the Const Declaration .............................................76
CRBASIC EXAMPLE 7. Alias and Unit Declaration ...............................................77
CRBASIC EXAMPLE 8. Definition and Use of a Data Table ..................................80
CRBASIC EXAMPLE 9. Use of the Disable Variable ..............................................82
CRBASIC EXAMPLE 10. Use of a Subroutine ........................................................83
CRBASIC EXAMPLE 11. BeginProg / Scan / NextScan / EndProg Syntax.............84
CRBASIC EXAMPLE 12. Measurement Instruction Syntax ....................................84
CRBASIC EXAMPLE 13. Use of Expressions in Parameters...................................86
CRBASIC EXAMPLE 14. Use of Arrays as Multipliers and Offsets........................86
CRBASIC EXAMPLE 15. Use of Variable Arrays to Conserve Code Space ...........88
CRBASIC EXAMPLE 16. Example Wireless Sensor Program For CR200(X) ......109
CRBASIC EXAMPLE 17. CRBASIC EXAMPLE. Radio Power Minimization
Program Examples .............................................................................................111
CRBASIC EXAMPLE 18. CRBASIC EXAMPLE. Two Rain Gages on a
CR200(X)...........................................................................................................112
CRBASIC EXAMPLE 19. Using TrigVar to Trigger Data Storage ........................126
CRBASIC EXAMPLE 20. CRBASIC EXAMPLE. Programming for two data
intervals in one data table...................................................................................127
CRBASIC EXAMPLE 21. Using NAN in Expressions...........................................153

viii
Section 1. Introduction
Whether in extreme cold in Antarctica, scorching heat in Death Valley, salt
spray from the Pacific, micro-gravity in space, or the harsh environment of your
office, Campbell Scientific dataloggers support research and operations all over
the world. Our customers work a broad spectrum of applications, from those
more complex than any of us imagined, to those simpler than any of us thought
practical. The limits of the CR200(X) are defined by our customers. Our intent
with the CR200(X) manual is to guide you to the tools you need to explore the
limits of your application.

You can take advantage of the CR200(X)'s powerful analog and digital
measurement features by spending a few minutes working through the
Quickstart Tutorial (p. 3) and the Overview (p. 23). For more demanding
applications, the remainder of the manual and other Campbell Scientific
publications are available. If you are programming with CRBASIC, you will
need the extensive Help available with the CRBASIC Editor software.

This manual is organized to take you progressively deeper into the complexity
of CR200(X) functions. You may not find it necessary to progress beyond the
Quickstart Tutorial (p. 3) or Overview (p. 23) sections. Quickstart Tutorial (p.
3) gives a cursory view of CR200(X) data acquisition and walks you through a
first attempt at data acquisition. Overview (p. 23) reviews salient topics, which
are covered in-depth in subsequent sections and appendices.

More in-depth study requires other Campbell Scientific publications, most of

which are available on-line at www.campbellsci.com. Generally, if a particular
feature of the CR200(X) requires a peripheral hardware device, more
information is available in the manual written for that device. Manuals for
Campbell Scientific products are available at www.campbellsci.com.

If you are unable to find the information you need, please contact us at 435-753-
2342 and speak with an applications engineer. Or you can email us at
[email protected].

1.1 CR200(X) series Datalogger Models

Models CR200X and CR200 Dataloggers do not have a built-in spread spectrum
radio.

The CR206X, CR211X, and CR216X combine the CR200X datalogger with a
spread spectrum radio for telemetering data. The different model numbers are
for different spread spectrum frequency ranges:

1
Section 1. Introduction

Table 1. CR200 series Dataloggers with Built-In Radio

Model Frequency Where Used

CR206X 915 MHz U.S./Canada

CR206 (retired)
CR205 (retired)

CR211X 922 MHz Australia/Israel

CR211 (retired)
CR210 (retired)

CR216X 2.4 GHz Worldwide

CR216 (retired)
CR215 (retired)

The CR295X and CR295 (retired) GOES Dataloggers include an additional

9-pin serial port that allow communications with a TX320, the retired TX312, or
the retired SAT HDR GOES satellite transmitter. While the CR295 required a
special operating system, the CR295X does not.

Note: Throughout this manual CR200(X) will be used to refer to all of the
different models of datalogger in the CR200-series and CR200X-series. In the
cases where information applies only to a specific model or series of datalogger,
that will be clearly specified.

The CR200(X)-series dataloggers have the following enhanced features as

compared to the CR200-series dataloggers:

1. 128 Public variables can be used (CR200-series had 48).

2. 8 Data Tables can be declared (CR200-series had 4).

3. Compiled CRBasic program can be two times larger than for CR200-
series.

4. All CR200(X)-series CRBasic instructions are supported in a single

operating system. See CRBasic and CRBasic Help for a list of
available instructions. No new instructions have been added. If new
instructions are added in the future, they will apply only to the
CR200(X)-series dataloggers.

2
Section 2. Quickstart Tutorial
Quickstart tutorial gives a cursory look at CR200(X) data acquisition.

2.1 Primer - CR200(X) Data Acquisition

Data acquisition with the CR200(X) is the result of a step wise procedure
involving the use of electronic sensor technology, the CR200(X), a
telecommunications link, and PC datalogger support software.

2.1.1 Components of a Data Acquisition System

A typical data acquisition system is conceptualized in FIGURE. Data
Acquisition System Components (p. 3). A CR200(X) is only one part of a data
acquisition system. To acquire good data, suitable sensors and a reliable data
retrieval method are required. A failure in any part of the system can lead to
"bad" data or no data.

2.1.1.1 How Programmed Instructions Are Evaluated

The CR200(X) evaluates programmed instructions sequentially.

Figure 1: Data Acquisition System Components

2.1.1.2 Sensors
Suitable sensors accurately and precisely transduce environmental change into
measurable electrical properties by outputting a voltage, changing resistance,
outputting pulses, or changing states.

Read More! APPENDIX. Accuracy, Precision, and Resolution (Appendix p.

13)

3
Section 2. Quickstart Tutorial

2.1.1.3 Datalogger
CR200(X)s can measure most sensors with an electrical response. CR200(X)s
measure electrical signals and convert the measurement to engineering units,
perform calculations and reduce data to statistical values. Every measurement
does not need to be stored. The CR200(X) will store data in memory awaiting
transfer to the PC via external storage devices or telecommunications.

2.1.1.4 Data Retrieval

The main objective of a data acquisition system is to provide data files on a PC.

Data are copied, not moved, from the CR200(X) to the PC. Multiple users may
have access to the same CR200(X) without compromising data or coordinating
data collection activities.

A RS-232 port is integrated with the CR200(X) wiring panel to facilitate data
collection.

On-site serial communications are preferred if the datalogger is near the PC, and
the PC can dedicate a serial (COM) port for the datalogger or use a USB-to-
serial converter. On-site methods such as direct serial connection or infrared
link are also used when the user visits a remote site with a laptop or PDA.

In contrast, telecommunications provide remote access and the ability to

discover problems early with minimum data loss. Typically a base station radio
that is compatible with the radio internal to the CR200(X) will be the preferred
method of telecommunication. A variety of devices, such as telephone modems,
satellite transceivers, and TCP/IP network modems may be interfaced with the
base station for the most demanding applications.

2.1.2 CR200(X) Mounting

The CR200(X) module integrates electronics within a compact housing, making
it economical, small, and very rugged.

2.1.3 Wiring Panel

As shown in FIGURE. CR200(X) Wiring Panel p. 5, the CR200(X) provides
terminals for connecting sensors, power and communications devices. Internal
surge protection is incorporated with the input channels.

The CR200(X) uses spring-loaded terminal blocks for connecting sensors and
peripherals. This provides quick, vibration resistant connections. To attach
wires, insert a small flat blade screwdriver into the slot and push back. Insert
the wire and then bring the screwdriver forward.

Caution! Opening a terminal by prying the end may cause damage,

particularly at low temperatures.

4
 Section 2. Quickstart Tutorial

Figure 2: CR200(X) Wiring Panel

2.1.4 Battery Backup

A lithium battery backs up the CR200(X) clock, program, and memory if it
loses power.

2.1.5 Power Supply

The CR200(X) is powered by a nominal 12 volt DC source. Acceptable power
range is 7 to 16 VDC.

The CR200(X) does not have an internal power supply but does have
connections for an external battery and a built-in charging regulator for charging
a 12 V lead-acid battery from an external power source. Charging power can
come from a 16-22 VDC input such as a solar panel.

2.1.6 Antenna
For CR200(X) models with a built-in radio, an FCC authorized antenna is a
required component. An SMA male connector is provided on the CR200(X)
wiring panel for antenna connection. Antennas are either 900 MHz or 2.4 GHz
depending on the type of radio installed.

Read More! Appendix: Antenna p. 32

5
Section 2. Quickstart Tutorial

2.1.7 Analog Sensors

Analog sensors output continuous voltages that vary with the phenomena
measured.

Analog sensors connect to analog terminals. Analog terminals are configured as

single-ended, wherein sensor outputs are measured with respect to ground
(FIGURE. Analog Sensor Wired to Single-Ended Channel #1 (p. 6)). The
CR200(X) cannot perform differential voltage measurements.

Figure 3: Analog Sensor Wired to Single-Ended Channel #1

2.1.8 Bridge Sensors

Bridge sensors change resistance with respect to environmental change.
Resistance is determined by measuring the difference between the excitation
voltage supplied to the bridge and the voltage detected by the CR200(X)
returning from the bridge.

2.1.8.1 Voltage Excitation

The CR200(X) supplies a precise excitation voltage via excitation terminals.
Return voltage is measured on single ended analog terminals. Because the
CR200(X) cannot make the differential voltage readings used with full bridge
and some half bridge circuits, only basic half bridge measurements can be made.
A wiring example is illustrated in FIGURE. Half Bridge Wiring Wind Vane
Potentiometer p. 7.

6
 Section 2. Quickstart Tutorial

Figure 4: Half Bridge Wiring -- Wind Vane Potentiometer

2.1.9 Pulse Sensors

The CR200(X) can measure switch closures, low-level AC signals (waveform
breaks zero volts), or voltage pulses. Compatible signal types are illustrated in
FIGURE. Pulse Input Types (p. 7). A pulse input wiring example is shown in
FIGURE. Pulse Input Wiring -- Anemometer Switch (p. 8).

Note Period averaging sensors are connected to analog channels.

Figure 5: Pulse Input Types

7
Section 2. Quickstart Tutorial

Figure 6: Pulse Input Wiring -- Anemometer Switch

2.1.10 Digital I/O Ports

The CR200(X) has 2 digital I/O ports selectable, under program control, as
binary inputs or control outputs. These are multi-function ports including:
device driven interrupts, switch closure pulse counting, high frequency pulse
counting, and SDI-12 communications. FIGURE. Control and Monitoring with
Digital I/O (p. 9), illustrates a simple application wherein a port is used to
control a device while a second port monitors the state of the device.

8
 Section 2. Quickstart Tutorial

Figure 7: Control and Monitoring with Digital I/O

2.1.11 RS-232 Sensors

The CR200(X) has an RS-232 input as shown in FIGURE. Location of RS-232
Port p. 10. As indicated in FIGURE. Use of RS-232 when Reading RS-232
Devices, p. 10 RS-232 sensors can be connected to the RS-232 port. The port
can be set up with various baud rates, parity options, stop bit options, and so
forth as defined in CRBASIC Help.

Note: For the CR200, SerialInput () is a special instruction, which is available

only in the special S operating system.

9
Section 2. Quickstart Tutorial

Figure 8: Location of RS-232 Port

Figure 9: Use of RS-232 when Reading RS-232 Devices

2.2 Hands-on Exercise - Measuring Temperature

This tutorial is designed to illustrate the function of the CR200(X). During the
exercise, the following items will be described.

• Attaching a temperature probe to analog differential terminals

• Creating a program for the CR200(X)

• Making a simple temperature measurement

• Sending data from the CR200(X) to a PC

• Viewing the data from the CR200(X)

10
 Section 2. Quickstart Tutorial

2.2.1 Hardware Setup

With Reference to FIGURE. Power and RS-232 Connections (p. 11).

1. Connect external power (7 – 16VDC) to the CR200 by inserting the

positive lead into the "Battery +".

2. Insert the negative lead into the "Battery-".

3. Connect the RS-232 cable (PN 10873, provided) between the RS-232
port on the CR200(X) and the RS-232 port on the PC. For computers
that have only a USB port, a USB Serial Adaptor (PN 17394 or
equivalent) is required.

Figure 10: Power and RS-232 Connections

2.2.2 Configuration
For this exercise, factory default settings will work. To change the PakBus
address or radio settings from their factory defaults, or if you are not sure what
settings are currently stored on the CR200(X), use Device Configuration Utility
or DevConfig software.

Read More! See DevConfig p. 59

2.2.3 PC200W Software Setup

1. Install the PC200W software onto a PC. Follow the on-screen prompts
during the installation process for the Program Folder and Destination
Location.

2. Open the PC200W software (FIGURE. PC200W Main Window (p.

13)). When the software is first run, the EZSetup Wizard will be run
automatically in a new window. This will configure the software to
communicate with the CR200(X). TABLE. PC200W EZSetup Wizard

11
Section 2. Quickstart Tutorial

Example Selections (p. 12) indicates what information needs to be

entered on each screen. Click on Next at the bottom of the screen to
advance to the next screen.

Table 2. PC200W EZSetup Wizard Example Selections.

Start the wizard to follow table entries

Screen Name Information Needed

Introduction Provides and introduction to the EZSetup Wizard along with
instructions on how to navigate through the wizard.

Datalogger Type and Name Select the CR200(X) from the scroll window.
Accept the default name of "CR200(X)."

COM Port Selection Select the correct COM port for RS-232 connection.
Typically, this will be COM1. Other COM numbers are
possible, especially when using a USB to serial cable.
Leave the COM Port Communication Delay at "00 seconds."
Note: When using a USB to serial cable, the COM number
may change if the cable is moved to a different USB port.
This will prevent data transfer between the software and
CR200(X). Should this occur, simply move the USB cable
back to the original port. If this is not possible, it will be
necessary to close the PC200W software and open it a
second time to refresh the available COM ports. Click on
"Edit Datalogger Setup" and change the COM port to the
new port number.

Datalogger Settings Used to configure how the CR200(X) communicates through

the COM port.
For this tutorial, accept the default settings.

Communication Setup Provides a summary of the settings made in previous

Summary screens.

Communications Test A communications test between the CR200(X) and PC can

be performed in this screen.
For this tutorial, the test is not required. Press Finish to exit
the Wizard.

After exiting the wizard, the main PC200W window becomes visible. The
window has several tabs available. By Default, the Clock/Program tab is visible.
This tab displays information on the currently selected datalogger along with
clock and program functions. The Monitor Data or Collect Data tabs may be
selected at any time.

A number of icons are available across the top of the window. These access
additional functions available to the user.

12
 Section 2. Quickstart Tutorial

Figure 11: PC200W Main Window

2.2.3.1 Programming With Short Cut

2.2.3.1.1 Short Cut Programming Objectives

This portion of the tutorial will use Short Cut to create a program that measures
air temperature (°C) with a 109 Temperature Probe, and rainfall (mm) with a
TE525WS rain gage. The CR200(X) will take samples every ten seconds and
store averages of these values at one minute intervals.

Even if the 109 Temperature Probe and TE525WS Rain Gage sensors are not
available, the programming example can still be followed. Without a 109 probe
connected the measurement result will be NAN; without a TE525WS connected
the measurement result will be 0. A rain gage can be simulated by straightening
a segment of each of two paper clips and inserting the straightened segment of
one paper clip into P_SW and the adjacent ground channel. To simulate a rain
gage tip, squeeze the paper clips together until they touch and then allow them
to spring apart.

2.2.3.1.2 Procedure (Short Cut Steps 1–6)

1. Click on the Short Cut icon in the upper-right corner of the PC200W
window. The icon resembles a clock face.

13
Section 2. Quickstart Tutorial

2. A new window will appear showing the option to create a new program
or open an existing program. Select New Program.

3. A drop-down list will appear showing different dataloggers. Select the

CR200(X) and click OK.

4. The program will now ask for the scan interval. Set the interval to 10
seconds and click OK.

5. A second prompt will ask for a choice of "Sensor Support." Select

"Campbell Scientific, Inc."

6. Under Available Sensors, expand the "Sensors" folder by clicking on

the "+" symbol. This shows several sub-folders. Expand the
"Temperature" folder to view the available sensors.

Figure 12: Short Cut Temperature Sensor Folder

2.2.3.1.3 Procedure (Short Cut Steps 7–9)

1. Double-click the 109 Temperature Probe sensor to add it to the

Selected category. Alternatively, highlight the Wiring Panel
Temperature sensor by clicking on it once, and then click on the arrow
between Available Sensors and Selected to add it to the Selected
sensors.

2. Click OK on the next screen to accept T109_C for the measurement

label, the DegC for the units.

3. Double click on the Meteorological application group. Double click

on Precipitation, and double click on the TE525 / TE525WS sensor to
add it to the selected sensors table. Click OK to accept Rain_mm for
the measurement label, and mm for the units.

14
 Section 2. Quickstart Tutorial

Figure 13: Short Cut Thermocoupler Wiring

2.2.3.1.4 Procedure (Short Cut Step 10)

1. Click on the Wiring Diagram link to view the sensor wiring diagram.
Attach the 109 Temperature Probe and TE525 Rain Gauge to the
CR200(X) as shown in the diagram. Click on Outputs to advance to the
next step.

Figure 14: Short Cut Wiring Diagram

2.2.3.1.5 Procedure (Short Cut Step 11)

1. The Outputs window displays a list of selected sensors on the left, and
data storage Tables on the right.

15
Section 2. Quickstart Tutorial

Figure 15: Short Cut Outputs Tab

2.2.3.1.6 Procedure (Short Cut Steps 12 –18)

1. By default, there are two Tables initially available. Both Tables have a
Store Every field along with a drop-down box to select the time units.
These are used to set the time interval when data is stored.

2. Only one Table is needed for this tutorial, so Table 2 can be removed.
Select Table 2 by clicking on its tab, and then click on Delete Table.

3. Change the Table Name to OneMin, and then change the interval to 1
minute (Store Every 1 Minutes).

4. Adding a measurement to the table is done by selecting the

measurement under Selected Sensors, and then clicking on one of the
processing buttons in the center of the window.

5. Click the Default sensor (battery voltage) and click the Minimum
button. Click the 109 temperature sensor and click the Average button.
Click the TE525 rain gauge sensor and click the Total button.

6. Click the Default sensor (battery voltage) and double click the
Minimum button. Click the 109 temperature sensor and double click
the Average button. Click the TE525 rain gauge sensor and double
click the Total button.

7. Click the Default sensor (battery voltage) and double click the
Minimum button. Do not store the time of minimum. Click the 109
temperature sensor and double click the Average button. Click the
TE525 rain gauge sensor and double click the Total button..

16
 Section 2. Quickstart Tutorial

Figure 16: Short Cut Output Table Definition

2.2.3.1.7 Procedure (Short Cut Step 19)

1. Click on Finish to compile the program. Give the program the name
"QuickStart." A prompt will ask if you want to send the program to the
datalogger. For this exercise choose No. A summary screen will
appear showing the compiler results. Any errors during compiling will
also be displayed.

Figure 17: Short Cut Compile Confirmation

2.2.3.1.8 Procedure (Short Cut Step 20)

1. Close this window by clicking on the "X" in the upper right corner.

17
Section 2. Quickstart Tutorial

2.2.3.2 Programming the CR200(X) and Collecting Data

2.2.3.2.1 Procedure (PC200W Step 1)

1. From the PC200W Clock/Program tab, click on the Connect button to

establish communications with the CR200(X). When communications
have been established, the text on the button will change to Disconnect.

Figure 18: PC200W Connect Button

2.2.3.2.2 Procedure (PC200W Steps 2–4)

1. Click the Set Clock button to synchronize the datalogger's clock with
the computer's clock.

2. Click on the Send Program button. A window will appear warning that
data on the datalogger will be erased. Answer "yes" to the prompt.
Another window will open. Browse to the C:\CampbellSci\SCWin
folder, select the QuickStart.CR2 file, and then click the Open button.
A status bar will appear while the program is sent to the CR200(X)
followed by a confirmation that the transfer was successful. Click OK
to close this window.

3. After sending a program to the CR200(X), a good practice is to

monitor the measurements to ensure they are reasonable. Select the
Monitor Data tab. The window now displays data found in the Public
Table coming from the CR200(X). To view the OneMin table, select an
empty cell in the display area, and then click on the Add button.

18
 Section 2. Quickstart Tutorial

Figure 19: PC200W Monitor Data Tab

2.2.3.2.3 Procedure (PC200W Step 5)

1. In the Add Selection window, click on the OneMin table, and then
click Paste. The OneMin table is now displayed in the main display.

Figure 20: PC200W Monitor Data Tab

2.2.3.2.4 Procedure (PC200W Step 6)

1. Click on the Collect Data tab. From this window, data is chosen to be
collected as well as the location where the collected data will be stored.

19
Section 2. Quickstart Tutorial

Figure 21: PC200W Collect Data Tab

2.2.3.2.5 Procedure (PC200W Steps 7–9)

1. Click the OneMin box so a check mark appears in the box. Under the
"What to Collect" heading, select "New data from datalogger." This
selects which data will be collected.

2. Click on the Collect button. A progress bar will appear as the data is
collected, followed by the message, "Collection Complete." Click OK
to continue.

3. To view the data, click on the View icon at the top of the window. This
opens a new window.

Figure 22: PC200W View Data Utility

20
 Section 2. Quickstart Tutorial

2.2.3.2.6 Procedure (PC200W Step 10)

1. Click on the Open File icon to open a file for viewing. Select the
"CR200Series_OneMin.dat" file and click on Open. The collected data is
now shown.

Figure 23: PC200W View Data Table

2.2.3.2.7 Procedure (PC200W Step 11)

1. Select any data column by clicking on it. To display the data in graphical
form, click on one of the Show Graph buttons. A graph with one Y-axis or
two Y-axes will be generated.

Figure 24: PC200W View Data Graph

2.2.3.2.8 Procedure (PC200W Step 12)

1. Close the Graph and View windows, and then close the PC200W program.

21
Section 2. Quickstart Tutorial

22
Section 3. Overview
3.1 CR200(X) Overview
The CR200(X) Datalogger is a precision instrument designed for low-power
measurement applications. CPU, analog inputs, digital outputs, and memory are
controlled by the operating system in conjunction with the user program. The
user program is written in CRBASIC, a programming language that includes
data processing and analysis routines and a standard BASIC instruction set.
Campbell Scientific's datalogger support software facilitates program
generation, editing, data retrieval, and real-time data monitoring (see Support
Software (p. 143)).

FIGURE. Features of a Data Acquisition System (p. 24) illustrates a common

CR200(X)-based data acquisition system.

The CR200(X) is a multimeter with memory and timekeeping. It is one part of

a data acquisition system. To acquire quality data, suitable sensors and reliable
telecommunications devices are also required.

Sensors transduce phenomena into measurable electrical forms, outputting

voltage, current, resistance, pulses, or state changes. The CR200(X), sometimes
with the assistance of various peripheral devices, can measure most electronic
sensors. Contact a Campbell Scientific applications engineer if you have
questions about a sensor's compatibility with a CR200(X) datalogger.

The CR200(X) measures analog voltage and pulse signals, representing the
magnitudes numerically. Numeric values are scaled to the unit of measure such
as millivolts and pulses, or in user specified engineering units such as wind
direction and wind speed. Measurements can be processed through calculations
or statistical operations and stored in memory awaiting transfer to a PC via
external storage or telecommunications.

23
Section 3. Overview

Figure 25: Features of a Data Acquisition System

3.1.1 Programmed Instructions Are Evaluated Sequentially

The CR200(X) evaluates programmed instructions sequentially.

24
 Section 3. Overview

3.1.2 Sensor Support

Read More! See Sensor Support (p. 37)

The following sensor types are supported by the CR200(X) datalogger. Refer to
Sensors (Appendix p. 29) for information on sensors available from Campbell
Scientific.

• Analog voltage

• Analog current (with a shunt resistor)

• Resistive bridges

• Pulse output

• Period output

• Frequency output

• SDI-12 sensors

A library of sensor manuals and application notes are available at

www.campbellsci.com to assist in measuring many sensor types. Consult with a
Campbell Scientific applications engineer for assistance in measuring unfamiliar
sensors.

3.1.3 Input / Output Interface: The Wiring Panel

The wiring panel of the CR200(X) is the interface to all CR200(X) functions.
Most CR200(X) functions are best introduced by reviewing features of the
CR200(X) wiring panel. FIGURE. CR200(X) Wiring Panel (p. 5) illustrates the
wiring panel and some CR200(X) functions accessed through it.

Read More! Read Measurement and Control Peripherals (p. 49) for more
information.

3.1.3.1 Measurement Inputs

Measurements require a physical connection with a sensor at an input channel
and CRBASIC programming to instruct the CR200(X) how to make, process,
and store the measurement. The CR200(X) wiring panel has the following input
channels:

Analog Voltage: 5 channels (SE 1–5).

• Input voltage range: 0 mV to 2500 mV.

• Measurement resolution: 0.6 mV

25
Section 3. Overview

Period Average: 4 channels (SE 1–4)

• Maximum input voltage: 4000 mV.

• Maximum frequency: 150 kHz

• Voltage threshold: counts cycles on transition from < 900 mV to >

2100 mV.

Note Both pulse count and period average measurements are used to measure
frequency output sensors. Yet pulse count and period average measurement
methods are different. Pulse count measurements use dedicated hardware --
pulse count accumulators, which are always monitoring the input signal, even
when the CR200(X) is between program scans. In contrast, period average
measurement instructions only monitor the input signal during a program scan.
Consequently, pulse count scans can usually be much less frequent than period
average scans. Pulse counters may be more susceptible to low frequency noise
because they are always "listening", whereas period averaging may filter the
noise by reason of being "asleep" most of the time. Pulse count measurements
are not appropriate for sensors that are powered off between scans, whereas
period average measurements work well since they can be placed in the scan to
execute only when the sensor is powered and transmitting a correct signal.

Period average measurements utilize a high-frequency digital clock to measure

time differences between signal transitions, whereas pulse count measurements
simply accumulate the number of counts. As a result, period average
measurements offer much better frequency resolution per measurement interval,
as compared to pulse count measurements. The frequency resolution of pulse
count measurements can be improved by extending the measurement interval by
increasing the scan interval and by averaging.

Pulse: 2 channels (P_SW, P_LL) configurable for counts or frequency of the

following signal types:

• High level square waves (P_SW)

• Switch closures (P_SW)

• Low-level A/C sine waves (P_LL)

Digital I/O: 2 channels (C1 - C2) configurable for SDI-12 communication,

state, frequency, and pulses. 5 analog channels (SE1–SE5) configurable for
input/output.

• C1 - C2: state, frequency, pulse.

• C1: SDI-12 input/output, state, frequency, pulse.

• SE 1–5: input/output, state.

26
 Section 3. Overview

3.1.3.2 Voltage Outputs

Read More! See Control Output (p. 49).

• Switched Analog Output (Excitation): two channels (VX1/VX2) for

precise voltage excitation ranging from +2500 mV or +5000 mV. These
channels are regularly used with resistive bridge measurements. Each
channel will source up to 25 mA.

• Digital I/O: 2 channels (C1 - C2) configurable for on / off and pulse output
duration.

• Switched 12 Volts (SW Battery): (switch on / off ) primary voltage under

program control for control of external devices requiring 12V DC, such as
humidity sensors. SW Battery can source up to 900 mA. See TABLE.
Current Sourcing Limits p. 38.

• CR200(X) used as a PLC (programmable logic controller): Utilizing

peripheral relays and analog output devices, the CR200(X) can manage
binary and variable control devices through the following output channels:

• Digital I/O: 2 channels (C1/C2) configurable for pulse output duration.

• Switched 12 Volts (SW Battery): (switches on/off) primary voltage

under program control for control of external devices requiring 12V
DC, such as humidity sensors. SW Battery can source up to 900 mA.
See TABLE. Current Sourcing Limits p. 38.

3.1.3.3 Grounding Terminals

Read More! See Grounding (p. 55).

Proper grounding will lend stability and protection to a data acquisition system.
It is the easiest and least expensive insurance against data loss-and the most
neglected. The following terminals are provided for connection of sensor and
datalogger grounding:

• Signal Grounds: 6 ground terminals ( ) used as reference for single-ended

analog inputs, pulse inputs, excitation returns, and as a ground for sensor
shield wires. Signal returns for pulse inputs should use terminals located
next to pulse inputs.

• Power Grounds: 6 terminals (G) used as returns for 5V, SW Battery, 12V,
and C1-C2 outputs. Use of G grounds for these outputs minimizes
potentially large current flow through the analog voltage measurement
section of the wiring panel, which can cause single-ended voltage
measurement errors.

• Ground Lug: 1 terminal ( ), the large ground lug is used to connect a

heavy gage wire to earth ground. A good earth connection is necessary to
secure the ground potential of the datalogger and shunt transients away
from electronics. Minimum 14 AWG wire is recommended.

27
Section 3. Overview

3.1.3.4 Power Terminals

Read More! See CR200(X) Power Supply (p. 53).

Power In

• Power Supply: External battery is connected to Battery+ and Battery-

terminals. Review power requirements and power supply options in
CR200(X) Power Supply (Appendix p. 30) before connecting power.

• Input voltages in excess of 18 V may damage the CR200 and/or power

supply. Power to charge a 12 V lead-acid battery (16-22 VDC) must be
connected to the Charge+ and Charge- terminals NOT to Battery+ and
Battery-.

Power Out

• Peripheral 12 V Power Source: 1 terminal (SWBattery) and the associated

ground (G) supply power to sensors and peripheral devices requiring
nominal 12 VDC. Sensors and peripheral devices may also share a
connection to the Battery+ and Battery- terminals which is the same as
connecting them directly to the battery. This supply may drop as low as 7
VDC before datalogger operation stops. Precautions should be taken to
minimize the occurrence of invalid data from underpowered sensors.

3.1.3.5 Communications Ports

Read More! See Telecommunications and Data Retrieval (p. 131) and PakBus
Overview (p. 133).

The CR200(X) is equipped with an RS-232 communications port. This port

allows the CR200(X) to communicate with other computing devices, such as a
PC, or with other Campbell Scientific dataloggers.

Note RS-232 communications normally operate well up to a transmission cable

capacitance of 2500 picofarads, or approximately 50 feet of commonly available
serial cable.

• 9-pin RS-232: Non-isolated port for communicating with a PC through the

supplied serial cable, serial sensors, or through 3rd party serial
telecommunications devices. Acts as a DTE device with a null-modem
cable.

Read More! See APPENDIX. Serial Port Pin Outs (Appendix p. 21).

Some versions of the CR200(X) include an optional spread spectrum radio for
wireless communication with other devices equipped with a spread spectrum
radio.

28
 Section 3. Overview

3.1.4 Power Requirements

Read More! See CR200(X) Power Supply (p. 53).

The CR200(X) operates from a DC power supply with voltage ranging from 7 to
16 V, and is internally protected against accidental polarity reversal. The
CR200(X) has modest input power requirements, typically an average current
drain of less than 3 mA. Models with built-in radios may have a higher average
current drain, depending on the radio’s power mode and amount of time the
radio is in use. Be sure to include the current usage of the radio and any
powered sensors when calculating power supply requirements.

In low power applications, the CR200(X) can operate for several months on
non-rechargeable batteries. Power systems for longer-term remote applications
typically consist of a charging source, a charge controller, and a rechargeable
battery. When AC line power is available, an AC/DC wall adapter and a
rechargeable battery can be used to construct a UPS (uninterruptible power
supply) in conjunction with the CR200(X)'s built-in voltage regulator/charge
controller. Contact a Campbell Scientific applications engineer for assistance in
acquiring the items necessary to construct a UPS.

Applications requiring higher current requirements, such as satellite or cellular

phone communications, should be evaluated by means of a power budget with a
knowledge of the factors required by a robust power system. Contact a
Campbell Scientific applications engineer if assistance is required in evaluating
power supply requirements.

Common power devices are:

• Batteries

• Alkaline D-cell - 1.5 V/cell

• Rechargeable Lead-Acid battery

• Charge Sources

• Solar Panels

• Wind Generators

• AC/DC wall adapters

Refer to APPENDIX. Power Supplies (Appendix p. 30) for specific model

numbers of approved power supplies.

3.1.5 Programming: Firmware and User Programs

The CR200(X) is a programmable instrument, adaptable to demanding
measurement and telecommunications requirements.

29
Section 3. Overview

3.1.5.1 Firmware: OS and Settings

Read More! See CR200(X) Configuration (p. 59).

Firmware consists of the operating system (OS) and durable configuration

settings. OS and settings remain intact when power is cycled.

Note The CR200(X) is shipped factory ready with all settings and firmware
necessary to communicate with a PC via RS-232 and to accept and execute user
application programs. OS upgrades are occasionally made available at
www.campbellsci.com.

For more complex applications, some settings may need adjustment.

Adjustments are accomplished with DevConfig Software (DevConfig (p. 59)) or
through datalogger support software (see Support Software (p. 143)).

OS files are sent to the CR200(X) with DevConfig or through the program Send
button in datalogger support software. When the OS is sent via DevConfig, most
settings are cleared, whereas, when sent via datalogger support software, most
settings are retained.

3.1.5.2 User Programming

Read More! See Programming (p. 69) and CRBASIC Programming

Instructions (p. 93) and CRBASIC help for more programming assistance.

A CRBASIC program directs the CR200(X) how and when sensors are to be
measured, calculations made, and data stored. A program is created on a PC and
sent to the CR200(X). Two Campbell Scientific software applications, Short Cut
and CRBASIC Editor, create CR200(X) programs.

• Short Cut creates a datalogger program and wiring diagram in four easy
steps. It supports most sensors sold by Campbell Scientific and is
recommended for creating simple programs to measure sensors and store
data.

• Programs generated by Short Cut are easily imported into CRBASIC Editor
for additional editing. For complex applications, experienced programmers
often create essential measurement and data storage code with Short Cut,
then edit the code with CRBASIC Editor. Note that once a Short Cut
generated program has been edited with CRBASIC Editor, it can no longer
be modified with Short Cut.

3.1.6 Memory and Data Storage

Read More! See Memory and Data Storage (p. 129).

The CR200(X) has 2K SRAM for communication buffers, calculations, and

variables, and 60K Flash EEPROM for the operating system and user program.
The CR200 originally had a 128K Serial Flash EEPROM for data storage.
Campbell Scientific has increased the data storage memory from 128 kbytes to

30
 Section 3. Overview

512 kbytes in newer CR200s and in all CR200(X)s. CR200s with the increased
memory have "512K" on their label.

Figure 26: CR200(X) Wiring Panel

3.1.7 Communications Overview

Read More! See Telecommunications and Data Retrieval (p. 131).

The CR200(X) communicates with external devices to receive programs, send

data, or act in concert with a network. The primary communication protocol is
PakBus. Modbus is also supported. Refer to APPENDIX. Telecommunications
Hardware (Appendix p. 32) for information on available communications
devices.

3.1.7.1 PakBus

Read More! See PakBus Overview (p. 133).

The CR200(X) communicates with Campbell Scientific support software,

telecommunication peripherals, and other dataloggers via PakBus, a proprietary
network communications protocol. PakBus is a protocol similar in concept to IP
(Internet protocol). By using signatured data packets, PakBus increases the
number of communications and networking options available to the CR200(X).
Communication can occur via RS-232 or RF.

31
Section 3. Overview

Advantages of PakBus:

• Simultaneous communication between the CR200(X) and other devices.

• Peer-to-peer communication-no PC required.

• Other PakBus dataloggers can be used as "sensors" to consolidate all data

into one CR200(X).

• Routing - the CR200(X) cannot act as a router, passing on messages

intended for another logger, but other dataloggers can. PakBus supports
automatic route detection and selection.

• Datalogger to datalogger communications-special CRBASIC instructions

simplify transferring data between dataloggers for distributed decision
making or control.

• In a PakBus network, each datalogger is set to a unique address before

being installed in the network. Default PakBus address is 1. To
communicate with the CR200(X), the datalogger support software (see
Telecommunications and Data Retrieval (p. 131)) must know the
CR200(X)'s PakBus address. The PakBus address is changed using the
DevConfig software, CR200(X) status table, or PakBus Graph software.

3.1.7.2 Modbus

Read More! See Modbus (p. 139).

The CR200(X) supports Modbus Master and Modbus Slave communication for
inclusion in Modbus SCADA networks.

3.1.8 Maintenance Overview

Read More! See Care and Maintenance.

With reasonable care, the CR200(X) should give many years of reliable service.

3.1.8.1 Protection from Water

The CR200(X) and most of its peripherals must be protected from moisture.
Moisture in the electronics will seriously damage, and probably render un-
repairable, the CR200(X). Water can come from flooding or sprinkler irrigation,
but most often comes as condensation. In most cases, protecting from water is as
easy as placing the CR200(X) in a weather tight enclosure with desiccant and
elevating the enclosure above the ground. The CR200(X) is shipped with
desiccant to reduce humidity. Desiccant should be changed periodically. Do not
completely seal the enclosure if lead acid batteries are present; hydrogen gas
generated by the batteries may build up to an explosive concentration. Refer to
APPENDIX. Enclosures (Appendix p. 31) for information on available weather
tight enclosures.

32
 Section 3. Overview

3.1.8.2 Protection from Voltage Transients

Read More! See Grounding (p. 55).

The CR200(X) must be grounded to minimize the risk of damage by voltage

transients associated with power surges and lightning induced transients. Earth
grounding is required to form a complete circuit for voltage clamping devices
internal to the CR200(X). Refer to APPENDIX. Voltage Transient Suppressors
(Appendix p. 34) for information on available surge protection devices.

3.1.8.3 Calibration

Read More! See Self-Calibration p. 41.

The CR200(X) uses an internal voltage reference to routinely calibrate itself. To

maintain electrical specifications, Campbell Scientific recommends factory
recalibration every two years. For calibration services, contact Campbell
Scientific to obtain a Return Materials Authorization (RMA) prior to shipping.

3.1.8.4 Replacing the Internal Battery

Caution Fire, explosion, and severe burn hazard! Misuse or improper
installation of the lithium battery can cause severe injury. Do not
recharge, disassemble, heat above 100°C (212°F), solder directly to the
cell, incinerate, or expose contents to water. Dispose of spent lithium
batteries properly.

The CR200(X) contains a lithium battery that operates the clock and SRAM
when the CR200(X) is not powered. The CR200(X) does not draw power from
the lithium battery while it is powered by an external source. In a CR200(X)
stored at room temperature, the lithium battery should last approximately 5
years (less at temperature extremes). Where the CR200(X) is powered most or
all of the time the lithium cell should last much longer.

The internal lithium battery must be replaced periodically. Factory replacement

is recommended. Contact Campbell Scientific to obtain an RMA prior to
shipping the CR200(X).

If the lithium cell is removed or allowed to discharge below the safe level, the
CR200(X) will still operate correctly while powered. Without the lithium
battery, the clock will reset and data is lost when power is removed.

A replacement lithium battery can be purchased from Campbell (part number

15598). TABLE. CR200(X) Lithium Battery Specifications p. 33 lists the
specifications of the battery. However, Campbell Scientific recommends that the
battery be replaced at the factory.

33
Section 3. Overview

Table 3. Internal Lithium Battery Specifications

Manufacturer Renata
Model CR2016 (3.6V)
Capacity 80 mAh
Self-discharge rate 1%/year @ 23°C
Operating temperature range -40°C to +85°C

3.2 PC Support Software

Read More! See Support Software (p. 143).

Several datalogger support software products for Windows are available.

Software for datalogger setup and simple applications, PC200W and Short Cut,
are available at no cost at www.campbellsci.com. For more complex
programming, telecommunications, networking, and reporting features, full-
featured products are available from Campbell Scientific.

• PC200W Starter Software is available at no charge at

www.campbellsci.com. It supports a transparent RS-232 connection
between PC and CR200(X), and includes Short Cut for creating CR200(X)
programs. Tools for setting the datalogger clock, sending programs,
monitoring sensors, and on-site viewing and collection of data are also
included.

• PC400 supports a variety of telecommunication options, manual data

collection, and data monitoring displays. Short Cut and CRBASIC Editor
are included for creating programs. PC400 does not support complex
communication options, such as phone-to-RF, PakBus® routing, or
scheduled data collection.

• LoggerNet supports combined telecommunication options, customized data

monitoring displays, and scheduled data collection. It includes Short Cut
and CRBASIC Editor for creating programs. It also includes tools for
configuring, trouble-shooting, and managing datalogger networks.
LoggerNet Admin and LoggerNet Remote are also available for more
demanding applications.

34
 Section 3. Overview

3.3 Specifications

35
Section 3. Overview

36
Section 4. Sensor Support
Several features give the CR200(X) the flexibility to measure many sensor
types. Contact a Campbell Scientific applications engineer if assistance is
required to assess sensor compatibility.

4.1 Powering Sensors

Read More! See CR200(X) Power Supply (p. 53).

The CR200(X) is a convenient router of power for sensors and peripherals

requiring a 2.5, 5 or 12 VDC source. It has one program-controlled switched 12
Volt terminal (SW Battery), and two switched voltage excitation terminals
(VX1, VX2). These terminals limit current internally for protection against
accidental short circuits. Sensors can be powered continuously by connecting to
the Battery + terminal, which is the same as connecting sensors directly to the
external battery.

Voltage on the Battery + and SW Battery terminals will changed with the DC
supply used to power the CR200(X). The switched voltage excitation terminals
are typically used to supply a brief excitation for a bridge measurement with the
ExDelSE () instruction, but can also be programmed to provide a continuous 2.5
V or 5 V using the Excite () instruction, which is enough to power many
sensors. Switched Unregulated (Nominal 12 Volt) (p. 38) shows the current
limits of SW Battery. Greatly reduced output voltages associated with SW
Battery, VX1, and VX2 due to current limit may occur if the current limits
given in the table in TABLE. Current Sourcing Limits p. 38 are exceeded.

4.1.1 Switched Precision

Voltage (0, 2500, 5000 mV)

Two switched analog output (excitation) terminals, VX1 and VX2, operate
under program control. Check the accuracy specification of these channels in
Specifications (p. 35) to understand their limitations. Specifications are only
applicable for loads not exceeding ±25 mA for 2.5 V excitation, or 10 mA for 5
V excitation. CRBASIC instructions that control excitation channels include:

• ExDelSE ()

• ExciteV ()

4.1.2 Continuous Unregulated (Nominal 12 Volt)

Voltage on the Battery + terminal will change with the CR200(X) external
battery voltage.

37
Section 4. Sensor Support

4.1.3 Switched Unregulated (Nominal 12 Volt)

Voltage on the SW Battery terminal will change with CR200(X) supply voltage.
The CRBASIC instruction SWBatt () controls the SW Battery terminal.

Table 4. Current Sourcing Limits

Terminal Limit
VX1, VX2 25 mA @ 2.5V
10 mA @ 5V

SW Battery < 900 mA @ 20°C

< 729 mA @ 40°C
< 630 mA @ 50°C
< 567 mA @ 60°C
< 400 mA @ 85°C

4.2 Voltage Measurement

4.2.1 Measurement Sequence
The first step in a voltage measurement is a calibration to measure the ground
offset. The calibration is performed once for each voltage measurement. The
CR200(X) measures analog voltages with a sample and hold analog to digital
(A/D) conversion. The A/D conversion is made with a 12-bit successive
approximation technique which resolves the signal voltage to one part in 4096
of the full scale 2.5 V range, which is 0.6 millivolts.

To reduce noise, 10 measurements are rapidly made and averaged to form the
result returned. The measurements that go into the average each take about 26
microseconds.

4.2.2 Measurement Accuracy

CR200(X) analog measurement error is calculated as
Error = Gain Error (%) + Offset Error

Gain error is expressed as ±% and is a function of input voltage and CR200(X)

temperature. It is minimized by factory calibration and increases with
component temperature and aging. Between -40°C and +50°C, gain error is
typically ±0.25% of the reading with a 1.2 millivolt offset. Worst case over that
same temperature range is ±1% of the reading with a 2.4 millivolt offset.

FIGURE. Voltage Measurement Accuracy (-40° to +50°C) p. 40 illustrates that

as magnitude of input voltage decreases, measurement error decreases.

38
 Section 4. Sensor Support

Note The accuracy specification includes only the CR200(X)’s contribution to

measurement error. It does not include the error of sensors.

For example, assume the following (see Specifications (p. 35)):

• Input Voltage: +2000 mV

• Programmed Measurement Instruction: VoltSE ()

• CR200(X) Temperature: Between -40°C and +50°C

Accuracy of the measurement is calculated as follows:

Error = Gain Error + Offset Error,

where
Gain Error = ± (2000 * 0.0025)

= ±5 mV

and
Offset Error = 1.2mV

Therefore,
Error = Gain Error + Offset Error

= ±5 mV + 1.2 mV.

= ±6.2 mV

A worst case accuracy in these conditions is

Error = ±(2000 mV * 0.01 + 2.4 mV) = ±22.4 mV

In contrast, the error for a 500 mV input under the same constraints is ±2.45 mV
typical and ±7.4 mV worst case.

39
Section 4. Sensor Support

Figure 27: Voltage Measurement Accuracy (0° to 40° C)

4.2.3 Voltage Range

The CR200(X) has one analog voltage range of 0 to 2.5 volts. The resolution
for a single A/D conversion is 0.6 millivolts.

4.2.4 Integration
Integration is used to reduce the noise included in a measurement. The
CR200(X) uses a form of digital integration. It makes 10 A/D conversions and
averages them for the result returned. The A/D conversions are made every 26
microseconds.

Averaging will also reduce signal noise from the sensor such as when water
level measured with a pressure transducer is changing because of pressure
fluctuations caused by wind.

Averaging also has an effect on the resolution. The resolution seen in the
numerical result is the resolution of a single A/D conversion (0.6 mV) divided
by the number of A/D conversions (10).

40
 Section 4. Sensor Support

4.2.5 Self-Calibration
A calibration measurement to measure the ground offset is made at the
beginning of each measurement instruction that includes a voltage
measurement. This calibration takes about 400 microseconds. Only one
calibration measurement is made per instruction regardless of the number of
reps.

The battery voltage is checked every 8 seconds to ensure it is within the

allowable range.

4.3 Bridge Resistance Measurements

Many sensors detect phenomena by way of change in a resistive circuit.
Thermistors, strain gages, and position potentiometers are examples. Resistance
measurements are special case voltage measurements. By supplying a precise,
known voltage to a resistive circuit, then measuring the returning voltage,
resistance can be calculated.

Two bridge measurement instructions are included in the CR200(X), ExDelSE

() and Therm109 (). ExDelSE () is used with sensors that have a simple half
bridge circuit. Therm109 () is used with Campbell Scientific’s 109-L thermistor
probe. Sensors with bridge circuits that require a differential voltage
measurement, such as full bridge or 3-wire half bridge, cannot be measured with
the CR200(X).

FIGURE. Half Bridge Circuit Used with ExDelSE (p. 41) shows the circuit that
is typically measured with ExDelSE (). In the diagram. Rs is normally the
sensor and Rf is normally a precision fixed (static) resistor. Vx is the excitation
voltage (either 2500 or 5000 mV) and V1 is the voltage (mV) measured by the
analog input channel.

Calculating the resistance of a sensor that is one of the legs of a resistive bridge
requires additional processing following the bridge measurement instruction.
FIGURE. Half Bridge Circuit Used with ExDelSE (p. 41) lists the schematics of
a typical half bridge configuration and the calculations necessary to compute the
resistance of any single resistor, provided the value of the other resistor in the
bridge circuit is known.

Figure 28: Voltage Excitation Bridge Circuit

41
Section 4. Sensor Support

4.3.1 Measurements Requiring AC Excitation

Some resistive sensors require AC Excitation. These include electrolytic tilt
sensors, soil moisture blocks, water conductivity sensors, and wetness sensing
grids. The use of DC excitation in these sensors can result in polarization, which
will cause erroneous measurement, shift calibration, or lead to rapid sensor
decay.

Other sensors, e.g., LVDTs (Linear Variable Differential Transformer), require

and AC excitation because they rely on inductive coupling to provide a signal.
DC excitation will provide no output.

CR200(X) bridge measurements cannot reverse excitation polarity to provide

AC excitation and avoid ion polarization. Sensors requiring AC excitation
should not be used with the CR200(X).

Other Campbell Scientific dataloggers (e.g. CR800 series, CR1000, CR3000)

are compatible with sensors that require AC excitation.

4.4 Pulse Count Measurement

FIGURE. Switch Closure Pulse Sensor p. 42 is a generalized schematic showing
connection of a pulse sensor to the CR200(X). The CR200(X) features two
dedicated pulse input channels, P_SW and P_LL, and two digital I/O channels,
C1and C2, for measuring pulse output sensors. Activated by the PulseCount ()
instruction, dedicated 16-bit counters on P_SW, P_LL, C1 and C2 are used to
accumulate all counts over the user specified scan interval. The value which is
output for each scan is the difference in the last known counter value and the
new counter value. Since the last count is maintained for each scan, even if the
counter rolls over between scans the correct count will be recorded. If the time
between scans is such that the counter exceeds 65,536 pulses during a scan, then
the counter will roll over twice resulting is an erroneous measurement.
PulseCount () instruction parameters specify the pulse input type, channel used,
and pulse output option.

Note: The PulseCount instruction must be executed once before the pulse or
control port is ready for input. This may be of particular concern for programs
with long scan intervals. For example, the PulseCount () instruction will not
yield a valid output until the turn of the second hour if the PulseCount ()
instruction is used within a program with a scan interval of 1 hour.

Figure 29: Switch Closure Pulse Sensor

42
 Section 4. Sensor Support

Note: The PulseCount () instruction should not be used in a conditional

statement or subroutine. To ensure all pulses are detected, it must be executed
each scan.

Execution of PulseCount () within a scan involves determining the accumulated

counts in each dedicated 16-bit counter since execution of the last PulseCount
(). PulseCount () parameter (POption) determines if the output is in counts
(POption = 0) or frequency (POption = 1). Counts are the preferred output
option for measuring number of tips from a tipping bucket rain gage, or the
number of times a door opens. Many pulse sensors, such as anemometers and
flow meters, are calibrated in terms of frequency (Hz or counts / second), and
are usually measured with the frequency option.

Resolution of the pulse counters is one count. Resolution of frequency is

(1/scan interval). For example, the frequency resolution of PulseCount()
returning a result every 1 second is 1 Hz. The resultant measurement will
bounce around by the resolution. For example, if you are scanning a 2.5 Hz
input once a second, in some intervals there will be 2 counts and in some 3. If
the pulse measurement is averaged, the correct value will be the result.

Accuracy is limited by a small scan interval error of ±(3 ppm of scan interval +
10 µs) plus the measurement resolution error of ± 1 Hz. The sum is essentially ±
1 Hz. Extending a 1 second measurement interval to 10 seconds, either by
increasing the scan interval or by averaging, improves the resulting frequency
resolution from 1 Hz to 0.1 Hz. Averaging can be accomplished by the Average
() instruction or by computing a running or spatial average through
programming.

4.4.1 Pulse input Channels

Read More! Review pulse counter specifications p. 35. Review pulse counter
programming in CRBASIC Help for the PulseCount () instruction.

43
Section 4. Sensor Support

FIGURE. Pulse Input Types (p. 7) illustrates pulse input types measured by the
CR200(X). Dedicated pulse input channel P_SW can be configured to read
high- frequency pulses or switch closure, while P_LL can be configured to read
a low-level AC signal. With a 100 kOhm pull-up resistor added to the wiring
panel P_LL, C1, or C2 can measure pulse input signals (See Pulse Input (P_SW
p. 44).

Figure 30: Pulse Input Types

4.4.1.1 Pulse Input (P_SW)

Internal hardware routes high-frequency pulse to an inverting CMOS input
buffer with input hysteresis. The CMOS input buffer is guaranteed to be an
output zero level with its input ≥ 2.7 V, and guaranteed to be an output one with
its input ≤ 0.9 V. An RC input filter with approximately a 1 µs time constant
precedes the inverting CMOS input buffer, resulting in an amplitude reduction
of high frequency signals between the P_SW terminal block and the inverting
CMOS input buffer as illustrated in FIGURE. Amplitude reduction of pulse-
count waveform. For a 0 to 5 Volt square wave applied to P_SW, the maximum
frequency that can be counted in pulse input mode is approximately 1 kHz.

Figure 31: Amplitude Reduction of Pulse-Count Waveform (before and

after 1 ms time constant filter)

44
 Section 4. Sensor Support

When a pulse channel is configured for pulse input mode, an internal 100 kΩ
pull-up resistor to +5 Volt on the P_SW input is automatically employed. This
pull-up resistor accommodates open-collector (open-drain) output devices for
high-frequency input. An external 100 kΩ pull-up resistor connecting Battery+
to P_LL, C1, or C2 must be added to perform pulse counting on any of those
channels (See Multiple Switch Closure Measurements p. 112).

The maximum input voltage on P_SW is 4 volts. For C1 and C2 the maximum
input voltage is 6.5 volts.

4.4.1.2 Low-Level AC (P_LL)

Rotating magnetic pickup sensors commonly generate AC output voltages
ranging from millivolts at low rotational speeds to several volts at high
rotational speeds. Channel P_LL contains internal signal conditioning hardware
for measuring low-level AC output sensors. P_LL measure signals ranging
from 20 mV RMS (±28 mV peak) to 14 V RMS (±20 V peak). Internal AC
coupling is incorporated in the low-level AC hardware to eliminate DC offset
voltages of up to ±0.5 V.

4.4.2 Pulse Input on Digital I/O Channels C1–C2

Read More! Review digital I/O channel specifications in Specifications p. 35.
Review pulse counter programming in CRBASIC Help for the PulseCount ()
instruction.

Digital I/O channels C1 – C2 can be configured to measure pulse input signals.

Pulse input signals require external 100 kΩ pull-up resistors to be connected
between Battery+ and the control ports. Maximum input voltage level is 6.5 V.
If pulse inputs greater than +6.5 V need to be measured, external signal
conditioning must employed. Contact Campbell Scientific for further
information.

Low-level AC signals cannot be measured directly on channels C1 – C2.

4.5 Period Averaging Measurements

The CR200(X) can measure the period of a signal on any single-ended analog
input channel (SE 1 - 5). The specified number of cycles are timed with a
resolution of 70 ns, making the resolution of the period measurement 70 ns
divided by the number of cycles chosen.

Cycles are counted as the input voltage transitions from less than 0.9 volts to
more than 2.1 volts. The maximum input voltage must be less than 4 volts. The
maximum frequency that can be detected is 150 kHz.

45
Section 4. Sensor Support

4.6 SDI-12 Recording

Read More! SDI-12 Sensor Support p. 112 and Serial Input / Output p. 105.

SDI-12 is a communications protocol developed to transmit digital data from

smart sensors to data acquisition units. It is a simple protocol, requiring only a
single communication wire. Typically, the data acquisition unit also supplies
power (12V and ground) to the SDI-12 sensor. The CR200(X) is equipped with
1 SDI-12 channel and an SDI12Recorder () CRBASIC instruction.

4.7 Cabling Effects on Measurements

Sensor cabling can have significant effects on sensor response and accuracy.
This is usually only a concern with sensors acquired from manufacturers other
than Campbell Scientific. Campbell Scientific sensors are engineered for
optimal performance with factory installed cables.

4.7.1 Analog Sensor Cables

Cable length in analog sensors is most likely to affect the signal settling time.
For more information, see Signal Settling Time.

4.7.2 Pulse Sensors

Because of the long interval between switch closures in tipping bucket rain
gages, appreciable capacitance can build up between wires in long cables. A
built up charge can cause arcing when the switch closes, shortening switch life.
As shown in FIGURE. Current Limiting Resistor in a Rain Gage Circuit (p. 46),
a 100 ohm resistor is connected in series at the switch to prevents arcing. This
resistor is installed on all rain gages currently sold by Campbell Scientific.

Figure 32: Current Limiting Resistor in a Tipping Bucket Rain Gage

Circuit

46
 Section 4. Sensor Support

4.7.3 Serial Sensors

4.7.3.1 SDI-12 Sensors
The SDI-12 standard allows cable lengths of up to 200 feet. Campbell Scientific
does not recommend SDI-12 sensor lead lengths greater than 200 feet; however,
longer lead lengths can sometimes be accommodated by increasing the wire
gage and/or powering the sensor with a second 12 vdc power supply placed near
the sensor.

47
Section 4. Sensor Support

48
Section 5. Measurement and Control
Peripherals
Peripheral devices expand the CR200(X) input / output capacity. Classes of
peripherals are discussed below according to use.

Read More! For complete information on available measurement and control

peripherals, go to APPENDIX. Sensors and Peripherals (Appendix p. 29),
www.campbellsci.com, or contact a Campbell Scientific applications engineer.

5.1 Control Output

Controlling power to an external device is a common function of the CR200(X).
On-board control terminals are available for binary (on / off) control.

Many devices are conveniently controlled with the SW Battery (Switched 12

Volt) terminal on the CR200(X). Applications requiring more control channels
or greater power sourcing capacity may be satisfied by using control ports C1 –
C2 in conjunction with single-channel switching relays.

5.1.1 Binary Control

5.1.1.1 Digital I/O Ports
Each of 2 digital I/O ports (C1 - C2) can be configured as an output port and set
low (0 V) or high (5 V) using the PortSet () or WriteIO () instructions. A digital
I/O port is normally used to operate an external relay driver circuit because the
port itself has limited drive capacity. Drive capacity is determined by the 5V
supply and a 330 ohm output resistance. It is expressed as:
Vo = 4.9V - (330 ohms) * Io

Where Vo is the drive limit, and Io is the current required by the external
device. FIGURE. Control Port Current Sourcing (p. 50) plots the relationship.

49
Section 5. Measurement and Control Peripherals

Figure 33: Control Port Current Sourcing

5.1.1.2 Switched 12 V Control

The SW Battery port can be set low (0 V) or high (12 V) using the SWBatt ()
instruction. The port is often used to control low power devices such as sensors
that require 12 V during measurement. Current sourcing must be limited to 900
mA or less at 20°C. See TABLE. Current Sourcing Limits (p. 38).

A 12V switching circuit, driven by a digital I/O port, is also available from
Campbell Scientific.

Note The SW Battery supply is unregulated and can supply up to 900 mA at

20°C. See TABLE. Current Sourcing Limits (p. 38). A resettable polymeric
fuse protects against over-current. Reset is accomplished by removing the load
or turning off the SW Battery for several seconds.

5.1.1.3 Relays and Relay Drivers

Compatible, inexpensive and reliable single-channel relay drivers for a wide
range of loads are available from various electronic vendors such as Crydom,
Newark, Mouser, etc.

5.1.1.4 Component Built Relays

FIGURE. Relay Driver Circuit with Relay (p. 51) shows a typical relay driver
circuit in conjunction with a coil driven relay which may be used to switch
external power to some device. In this example, when the control port is set
high, 12 V from the datalogger passes through the relay coil, closing the relay
which completes the power circuit and turns on the fan.

50
 Section 5. Measurement and Control Peripherals

In other applications it may be desirable to simply switch power to a device

without going through a relay. FIGURE. Power Switching without Relay (p. 51)
illustrates a circuit for switching external power to a device without using a
relay. If the peripheral to be powered draws in excess of 75 mA at room
temperature (limit of the 2N2907A medium power transistor), the use of a relay
is required.

Figure 34: Relay Driver Circuit with Relay

Figure 35: Power Switching without Relay

5.2 Other Peripherals

5.2.1 TIMs
Terminal Input Modules (TIMs) are devices that provide simple measurement
support circuits in a convenient package. TIMs include voltage dividers for
cutting the output voltage of sensors to voltage levels compatible with the
CR200(X), modules for completion of resistive bridges, and shunt modules for
measurement of analog current sensors. Refer to APPENDIX. Signal
Conditioners (Appendix p. 32) for information concerning available TIM
modules.

51
Section 5. Measurement and Control Peripherals

52
Section 6. CR200(X) Power Supply
Reliable power is the foundation of a reliable data acquisition system. When
designing a power supply, consideration should be made regarding worst-case
power requirements and environmental extremes.

Contact Campbell Scientific if assistance in selecting a power supply is needed,

particularly with applications in extreme environments.

6.1 Power Requirement

The CR200(X) operates from a DC power supply with voltage ranging from 7 to
16 V. It is internally protected against accidental polarity reversal. Input
voltages in excess of 18 V may damage the CR200(X) and/or power supply.

Caution The Battery + and Battery - terminals on the wiring panel are
not regulated by the CR200(X); they obtain the same power directly the
POWER IN terminal. When using the CR200(X) wiring panel to source
power to other 12 V devices, be sure the power supply regulates the
voltage within a the range specified by the manufacturer of the
connected device.

6.2 Calculating Power Consumption

Read More! Power Requirements (p. 29).

System operating time for batteries can be determined by dividing the battery
capacity (ampere-hours) by the average system current drain (amperes). The
CR200(X) typically has an average current drain of less than 3 mA. The duty
cycle of the radio will add to the current drain. Be sure to include the current
used by any powered sensors when calculating power supply requirements.

6.3 Power Supplies

APPENDIX. Power Supplies p. 30 lists external power supplies available from
Campbell Scientific, including alkaline and solar options. Complete power
supply information is available in manual or brochure form at
www.campbellsci.com.

6.3.1 Battery Connection

Any clean, 7 to 16 VDC supply may be connected to the Battery + and Battery -
connector terminals on the front panel. When connecting external power to the
CR200(X), insert the positive lead into the Battery + terminal. Insert the ground
lead into the Battery - terminal.

53
Section 6. CR200(X) Power Supply

Auxiliary photovoltaic power sources may be used to maintain charge on lead

acid batteries. Unregulated solar panels may be connected to Charge + and
Charge – channels on the datalogger wiring panel.

When selecting a solar panel, a rule-of-thumb is that on a stormy overcast day

the panel should provide enough charge to meet the system current drain
(assume 10% of average annual global radiation, kW/m2). Specific site
information, if available, could strongly influence the solar panel selection. For
example, local effects such as mountain shadows, fog from valley inversion,
snow, ice, leaves, birds, etc. shading the panel should be considered.

If help is needed in determining system power requirements, contact Campbell

Scientific's Marketing Department.

54
Section 7. Grounding
Grounding the CR200(X) and its peripheral devices and sensors is critical in all
applications. Proper grounding will ensure the maximum ESD (electrostatic
discharge) protection and higher measurement accuracy.

7.1 ESD Protection

ESD (electrostatic discharge) can originate from several sources, the most
common, and most destructive, being primary and secondary lightning strikes.
Primary lightning strikes hit the datalogger or sensors directly. Secondary
strikes induce a voltage in power lines or sensor wires.

The primary devices for protection against ESD are gas-discharge tubes (GDT).
All critical inputs and outputs on the CR200(X) are protected with GDTs or
transient voltage suppression diodes. GDTs fire at 150 V to allow current to be
diverted to the earth ground lug. To be effective, the earth ground lug must be
properly connected to earth (chassis) ground. The power ground and signal
grounds have independent paths to the ground lug.

The 9-pin serial port is another path for transients. Communications paths such a
telephone or short-haul modem lines should be provided spark gap protection at
installation. Spark gap protection is often an option with these products, so it
should always be requested when ordering. Spark gaps for these devices must be
connected to either the earth ground lug, the enclosure ground, or to the earth
(chassis) ground.

A good earth (chassis) ground will minimize damage to the datalogger and
sensors by providing a low resistance path around the system to a point of low
potential. Campbell Scientific recommends that all dataloggers be earth
(chassis) grounded. All components of the system (dataloggers, sensors,
external power supplies, mounts, housings, etc.) should be referenced to one
common earth (chassis) ground.

In the field, at a minimum, a proper earth ground will consist of a 6 to 8 foot

copper sheathed grounding rod driven into the earth and connected to the
CR200(X) Ground Lug with a 12 AWG wire. In low conductive substrates, such
as sand, very dry soil, ice, or rock, a single ground rod will probably not provide
an adequate earth ground. For these situations, consult the literature on lightning
protection or contact a qualified lightning protection consultant.

In vehicle applications, the earth ground lug should be firmly attached to the
vehicle chassis with 12 AWG wire or larger.

In laboratory applications, locating a stable earth ground is challenging, but still

necessary. In older buildings, new AC receptacles on older AC wiring may
indicate that a safety ground exists when in fact the socket is not grounded. If a
safety ground does exist, it is good practice to verify that it carries no current. If
the integrity of the AC power ground is in doubt, also ground the system
through the buildings, plumbing or another connection to earth ground.

55
Section 7. Grounding

7.1.1 Lightning Protection

The most common and destructive ESDs are primary and secondary lightning
strikes. Primary lightning strikes hit instrumentation directly. Secondary strikes
induce voltage in power lines or wires connected to instrumentation. While
elaborate, expensive and nearly infallible lightning protection systems are
available, Campbell Scientific has for many years employed a simple and
inexpensive design that protects most systems in most circumstances. It is,
however, not infallible.

Note Lightning strikes may damage or destroy the CR200(X) and associated
sensors and power supplies.

In addition to protections discussed in ESD Protection (p. 55), use of a simple

lightning rod and low-resistance path to earth ground is adequate protection in
many installations. A lightning rod serves two purposes. Primarily, it serves as a
preferred strike point. Secondarily, it dissipates charge, reducing the chance of a
lightning strike. FIGURE. Lightning Protection Scheme (p. 57) shows a simple
lightning protection scheme utilizing a lightning rod, metal mast, heavy gage
ground wire, and ground rod to direct damaging current away from the
CR200(X).

56
 Section 7. Grounding

Figure 36: Lightning Protection Scheme

7.2 Single-Ended Measurement Reference

Low-level single-ended voltage measurements are sensitive to ground potential
fluctuations. Although the CR200(X) is not sensitive enough for low-level
measurements and ground potential fluctuations are not usually a problem, the
grounding scheme in the CR200(X) has been designed to eliminate ground
potential fluctuations due to changing return currents from SW Battery,
excitation channels, and the control ports. This is accomplished by utilizing
separate signal and shield grounds ( ) and power grounds (G). To take
advantage of this design, observe the following grounding rule:

Note Always connect a device's ground next to the active terminal associated
with that ground. Several ground wires can be connected to
the same ground terminal.

57
Section 7. Grounding

Examples:

• Connect grounds associated with SW Battery, VX1 (EX1), VX2 (EX2), C1,
and C2 to G terminals.

• Connect the low side of single-ended sensors to the nearest ( ) terminal on

the analog input terminal blocks.

• Connect shield wires to the nearest ( ) terminal on the analog input

terminal blocks.

58
Section 8. CR200(X) Configuration
The CR200(X) may require changes to factory default settings depending on the
application. Most settings concern telecommunications between the CR200(X)
and a network or PC.

Note The CR200(X) is shipped factory ready with all settings and firmware
necessary to communicate with a PC via RS-232 and to accept and execute user
application programs.

Prior to running DevConfig, connect a serial cable from the computer COM port
to the RS-232 on the datalogger as shown in Figure. Power and RS-232
Connections p. 11.

8.1 DevConfig
DevConfig (Device Configuration Utility) is the preferred tool for configuring
the CR200(X). It is made available as part of LoggerNet, PC400, and at
www.campbellsci.com.

Features of DevConfig include:

• Communicates with devices via direct RS-232 only.

• Sends operating systems to supported device types.

• Sets datalogger clocks and sends program files to dataloggers.

• Identifies operating system types and versions.

• Provides a reporting facility wherein a summary of the current

configuration of a device can be shown, printed or saved to a file. The file
can be used to restore settings, or set settings in like devices.

• Provides a terminal emulator useful in configuring devices not directly

supported by DevConfig's graphical user interface.

• Shows Help as prompts and explanations. Help for the appropriate settings
for a particular device can also be found in the user's manual for that
device.

• Updates from Campbell Scientific's web site.

As shown in FIGURE. DevConfig CR200(X) Utility (p. 60), the DevConfig

window is divided into two main sections: the device selection panel on the left
side and tabs on the right side. After choosing a device on the left, choose from
the list of the serial ports (COM1, COM2, etc.) installed on the PC. A selection
of baud rates is offered only if the device supports more than one baud rate. The
page for each device presents instructions to set up the device to communicate
with DevConfig. Different device types offer one or more tabs on the right.

59
Section 8. CR200(X) Configuration

Figure 37: DevConfig Utility

8.2 Sending the Operating System

The CR200(X) is shipped with the operating system pre-loaded. However, OS
updates are made available at www.campbellsci.com and can be sent to the
CR200(X).

Since sending an OS to the CR200(X) resets memory, data loss will certainly
occur. Depending on several factors, the CR200(X) may also become
incapacitated for a time. Consider the following before updating the OS.

1. Is sending the OS necessary to correct a critical problem? -- If not,

consider waiting until a scheduled maintenance visit to the site.

2. Is the site conveniently accessible such that a site visit can be

undertaken to correct a problem of reset settings without excessive
expense?

If the OS must be sent, and the site is difficult or expensive to access, try the OS
download procedure on an identically programmed, more conveniently located
datalogger.

8.2.1 Sending OS with DevConfig

FIGURE. DevConfig OS Download Window (p. 61) and FIGURE. Dialog Box
Confirming OS Download (p. 61) show DevConfig windows displayed during
the OS download process.

Caution Sending an operating system with DevConfig will erase all

existing data and reset all settings to factory defaults.

60
 Section 8. CR200(X) Configuration

Figure 38: DevConfig OS Download Window

Text in the Send OS tab lists instructions for sending an operating system to the
CR200(X).

When the Start button is clicked, DevConfig offers a file open dialog box that
prompts for the operating system file (*.obj file). When the CR200(X) is
powered-up, DevConfig starts to send the operating system.

When the operating system has been sent, a confirming message dialog box.

Figure 39: Dialog Box Confirming OS Download

61
Section 8. CR200(X) Configuration

The information in the dialog helps to corroborate the signature of the operating
system sent.

8.3 Settings
8.3.1 Settings via DevConfig
The CR200(X) has a number of properties, referred to as "settings", some of
which are specific to the PakBus® communications protocol.

Read More! PakBus® is discussed in PakBus® Overview (p. 133) and the
PakBus® Networking Guide available at www.campbellsci.com.

DevConfig | Settings Editor tab provides access to most PakBus® settings,

however, the DevConfig | Deployment tab makes configuring most of these
settings easier.

Figure 40: DevConfig Settings Editor

As shown in FIGURE. DevConfig Settings Editor (p. 62), the top of the Settings
Editor is a grid that allows the user to view and edit the settings for the device.
The grid is divided into two columns with the setting name appearing in the left
hand column and the setting value appearing in the right hand column. Change
the currently selected cell with the mouse or by using up-arrow and down-arrow
keys as well as the Page-Up and Page-Down keys. When clicking in the setting
names column, the value cell associated with that name will automatically be
made active. Edit a setting by selecting the value, pressing the F2 key or by

62
 Section 8. CR200(X) Configuration

double clicking on a value cell with the mouse. The grid will not allow read-
only settings to be edited.

The bottom of the Settings Editor displays help for the setting that has focus on
the top of the screen.

Once a setting is changed, click Apply or Cancel. These buttons will only
become enabled after a setting has been changed. If the device accepts the
settings, a configuration summary dialogue is shown (FIGURE. Summary of
CR200(X) Configuration p. 63) that gives the user a chance to save and print the
settings for the device.

Figure 41: Summary of CR200(X) Configuration

Clicking the Factory Defaults button on the Settings Editor will send a
command to the device to revert to its factory default settings. The reverted
values will not take effect until the final changes have been applied. This button
will remain disabled if the device does not support the DevConfig protocol
messages.

Clicking Save on the summary screen will save the configuration to an XML
file. This file can be used to load a saved configuration back into a device by
clicking Read File and Apply.

63
Section 8. CR200(X) Configuration

8.3.1.1 Deployment Tab

Figure 42: DevConfig Deployment Tab

As shown in FIGURE. DevConfig Deployment Tab p. 64, the Deployment tab

allows the user to configure the datalogger prior to deploying it. Deployment
tab settings can also be accessed through the Setting Editor tab and the Status
table.

The CR200(X) default PakBus address is 1. Unless the CR200(X) is used in a

network, there may be no need to change the PakBus address or any other
default setting.

To change the PakBus address, use the up and down arrows next to the PakBus
Address field or key in the desired number (e.g., 5) and click the Apply button.

The Spread Spectrum radios in the CR200(X) series, and in the RF401, have
address, frequency, and power settings. These addresses are not PakBus
addresses but an address the radio encodes in its message. For radios in a
PakBus network to talk to each other the address and frequency settings must be
the same in ALL radios.

To change radio settings, use the up and down arrows or drop-down menus next
to the field of interest and click the Apply button when finished.

• Hop Sequence specifies the hopping sequence that will be used for the
built-in radio. Spread Spectrum radios have a band of frequencies that they
use. The radios “hop” from one frequency to another within this band,
allowing multiple sets of radios to communicate at the same time without
interfering with each other. This value should be set to match the Hop

64
 Section 8. CR200(X) Configuration

Sequence value of the RF400 series base station used to communicate with
the CR200(X) so they can contact each other.
• Network specifies the radio network address of the built-in radio which is
combined with the radio address and sent as part of a packet header with
each message. This value should be set to match the network address of the
RF400 series base station used to communicate with the CR200(X).
• Address specifies the address of the built-in radio which is combined with
the network value and sent as part of a packet header with each message.
This value should be set to match the address of the RF400 series base
station used to communicate with the CR200(X).
• Power Mode specifies the power wait state that will be set in the built-in
radio and how much power the CR200(X) radio consumes from its power
supply. This value should be consistent with the RF400 series base station
used to communicate with the CR200(X).
• RF Protocol identifies the radio protocol that will be used for the
CR200(X). For networks that include older CR205 and RF400 operating
systems this will be Transparent. If no devices with older operating
systems are present in the network PakBus Aware should be used.
• Help is displayed at the bottom of the Deployment tab. When finished,
Apply the settings to the datalogger. The Summary window will appear.
Save or Print the settings to archive or to use as a template for another
datalogger.
• Cancel causes the datalogger to ignore the changes. Read File provides the
opportunity to load settings saved previously from this or another similar
datalogger. Changes loaded from a file will not be written to the datalogger
until Apply is clicked.

8.3.1.2 Logger Control Tab

Figure 43: DevConfig Logger Control Tab

65
Section 8. CR200(X) Configuration

• Clocks in the PC and CR200(X) are checked every second and the
difference displayed. The System Clock Setting allows entering what
offset, if any, to use with respect to standard time (Local Daylight Time or
UTC, Greenwich mean time). The value selected for this control is
remembered between sessions. Clicking the Set Clock button will
synchronize the station clock to the current computer system time.

• Current Program displays the current program known to be running in the

datalogger. This value is empty if there is no current program.

• The Last Compiled field displays the time when the currently running
program was last compiled by the datalogger. As with the Current Program
field, this value is read from the datalogger if it is available.

• Last Compile Results shows the compile results string as reported by the
datalogger.

• The Send Program button presents an open file dialog from which to select
a program file to be sent to the datalogger. The field above the button is
updated as the send operation progresses. When the program has been sent
the Current Program, Last Compiled, and Last Compile Results fields are
filled in.

8.3.2 Settings via CRBASIC

Some variables in the status table can be requested or set during program
execution using the CRBASIC SetStatus () command. Entries can be requested
or set by setting a Public or Dim variable equivalent to the status table entry, as
can be done with variables in any data table. For example, to set a variable, x,
equal to a status table entry, the syntax is,
x = Status.StatusTableEntry

Careful programming is required when changing settings via CRBASIC to

ensure users are not inadvertently blocked from communicating with the
CR200(X), the remedy for which may be a site visit.

8.3.3 Settings via Terminal Emulator

The CR200(X) has a simple terminal interface that can be accessed with a PC
running a terminal emulator such as those available in PC200, PC400, or
LoggerNet.

Terminal mode is entered while the PC is in telecommunications with the

datalogger through a terminal emulator program. It is easily accessed through
Campbell Scientific datalogger support software, but is accessible with terminal
emulator programs such as Windows Hyperterminal. Datalogger keyboards and
displays cannot be used.

The terminal emulator is accessed by navigating to the Datalogger menu in

PC200W, the Datalogger menu in the Connect screen of LoggerNet, or the
Tools menu in PC400. A serial cable must be connected between the
computer/terminal and the CR200(X) in order to establish communications.

66
 Section 8. CR200(X) Configuration

The CR200(X) will time out and exit the terminal mode if it does not receive a
command within 12 seconds.

Enter a command by pressing the command followed by the carriage return.

The commands are:

Commands Action (what returns)

A Trap Code 16 Information
"OK" = memory ok
"2005-7-14 13:56:6=16" = memory failure, 16 denotes trap code 16,
date/time is when it occurred.

NOTE: When a trap code 16 happens, the datalogger suspends running

the program and the red LED flashes twice every scan interval. A trap
code of 16 means that the datalogger’s memory needs to be replaced.
1 Get clock
2 Set clock (after setting clock, exits terminal mode)
3 Status codes
4 Status table
5 Public table (real time values)
6 Most recent record from user defined table 1
7 Most recent record from user defined table 2
8 Most recent record from user defined table 3
9 Most recent record from user defined table 4
SDI12 Goes into the SDI-12 terminal mode and remains there

8.3.4 Durable Settings

Many CR200(X) settings can be changed remotely over a telecommunications
link either directly or as part of the CRBASIC program. This convenience
comes with the risk of inadvertently changing settings and disabling
communications. Such an instance will likely require an on-site visit to correct
the problem. For example, digital cell modems are often controlled by a
switched 12 Volt (SW Battery) channel. SW Battery is normally off, so, if the
program controlling SW Battery is disabled, such as by replacing it with a
program that neglects SW Battery control, the cell modem is switched off and
the remote CR200(X) drops out of telecommunications.

67
Section 8. CR200(X) Configuration

68
Section 9. Programming
9.1 Inserting Comments into Program
Comments are non-functioning text placed within the body of a program to
document or clarify program algorithms.

As shown in CRBASIC EXAMPLE. Inserting Comments (p. 69), comments are

inserted into a program by preceding the comment with a single quote (').
Comments can be entered either as independent lines or following CR200(X)
code. When the CR200(X) compiler sees a single quote ('), it ignores the rest of
the line.

CRBASIC EXAMPLE 1. Inserting Comments

'Declaration of variables starts here.
Public Start(6) 'Declare the start time array

9.2 Sending Programs

The CR200(X) requires a program be sent to its memory to direct measurement,
processing, and data storage operations. Programs are sent with LoggerNet /
PC400 / RTDAQ / PC200W datalogger support software.

Programs can also be sent from Device Configuration Utility (DevConfig). A

good practice is to always retrieve data from the CR200(X) before sending a
program, otherwise, data may be lost.

The CR200(X) does not have an on-board compiler to create the binary (.BIN)
program file required by the datalogger. Instead, the datalogger support
software creates a binary file using the appropriate compiler. The compiler is
chosen to match the version of operating system found in the CR200(X) and a
BIN file with the same filename as the selected CR2 file is created and sent to
the datalogger.

It is important that the compiler used match the operating system version in the
datalogger. If a different compiler is used, the program send will fail.
Compilers are typically stored at C:\Campbellsci\Lib\CR200(X)Compilers.

The most current CR200(X) operating system along with compiler and CRBasic
Editor support files may be obtained at www.campbellsci.com/downloads.

9.3 Writing Programs

Programs are created with either Short Cut or CRBASIC Editor. Short Cut is
available at no charge at www.campbellsci.com. CRBASIC Editor is a program

69
Section 9. Programming

in the LoggerNet / PC400 datalogger support software suites. Programs can be

up to 19.6 KBytes in size although typical programs are smaller.

9.3.1 Short Cut Editor and Program Generator

Short Cut is easy-to-use menu-driven software that presents the user with lists of
predefined measurement, processing, and control algorithms from which to
choose. The user makes choices and Short Cut writes the CRBASIC code
required to perform the tasks. Short Cut creates a wiring diagram to simplify
connection of sensors and external devices. Quickstart Tutorial (p. 3) works
through a measurement example using Short Cut.

For many complex applications, Short Cut is still a good place to start. When as
much information as possible is entered, Short Cut will create a program
template from which to work, already formatted with most of the proper
structure, measurement routines, and variables. The program can then be edited
further using CRBASIC Program Editor.

9.3.2 CRBASIC Editor

CR200(X) application programs are written in a variation of BASIC (Beginner's
All-purpose Symbolic Instruction Code) computer language, CRBASIC
(Campbell Recorder BASIC). CRBASIC Editor is a text editor that facilitates
creation and modification of the ASCII text file that constitutes the CR200(X)
application program. CRBASIC Editor is available as part of LoggerNet /
PC400 / RTDAQ datalogger support software packages.

Fundamental elements of CRBASIC include:

• Variables - named packets of CR200(X) memory into which are stored

values that normally vary during program execution. Values are typically
the result of measurements and processing. Variables are given an
alphanumeric name and can be dimensioned into arrays of related data.

• Constants - discrete packets of CR200(X) memory into which are stored

specific values that do not vary during program executions. Constants are
given alphanumeric names and assigned values at the beginning
declarations of a CRBASIC program.

Note Keywords and predefined constants are reserved for internal CR200(X)
use. If a user programmed variable happens to be a keyword or predefined
constant, a runtime or compile error will occur. To correct the error, simply
change the variable name by adding or deleting one or more letters, numbers, or
the underscore (_) from the variable name, then recompile and resend the
program. CRBASIC Help provides a list of keywords and pre-defined constants.

• Common instructions - Instructions and operators used in most BASIC

languages, including program control statements, and logic and
mathematical operators.

• Special instructions - Instructions unique to CRBASIC, including

measurement instructions that access measurement channels, and

70
 Section 9. Programming

processing instructions that compress many common calculations used in

CR200(X) dataloggers.

These four elements must be properly placed within the program structure.

9.4 Numerical Formats

Four numerical formats are supported by CRBASIC. Most common is the use of
base 10 numbers. Scientific notation, binary, and hexadecimal formats may also
be used, as shown in TABLE. Formats for Entering Numbers in CRBASIC (p.
71). Only standard base 10 notation is supported by Campbell Scientific
hardware and software displays.

Table 5. Formats for Entering Numbers in CRBASIC

Format Example Base 10 Equivalent Value
Standard 6.832 6.832
-8
Scientific notation 5.67E-8 5.67X10
Binary &B1101 11
Hexadecimal &HFF 255

Binary format is useful when loading the status (1 = high, 0 = low) of multiple
flags or ports into a single variable, e.g., storing the binary number
&B11100000 preserves the status of flags 8 through 1. In this case, flags 1 - 5
are low, 6 - 8 are high. CRBASIC EXAMPLE. Load Binary Information into a
Variable (p. 71) shows an algorithm that loads binary status of flags into a
LONG integer variable.

CRBASIC EXAMPLE 2. Load binary information into a single variable

Public FlagInt
Public Flag(8)
Public I

DataTable (FlagOut,True,1000)
Sample (1,FlagInt)
EndTable
BeginProg
Scan (1,Sec)
FlagInt = 0
For I = 1 To 8
Flag (I) = IIF (Flag(I)= 0,0,-1)
If Flag(I) = true then
FlagInt = FlagInt + 2 ^ (I - 1)
EndIf
Next I
CallTable FlagOut
NextScan
EndProg

71
Section 9. Programming

9.5 Structure
TABLE. CRBASIC Program Structure (p. 72) delineates CRBASIC program
structure:

Table 6. CRBASIC Program Structure

Declarations Define datalogger memory usage. Declare constants,
variables, aliases, units, and data tables.
Declare constants List fixed constants

Declare Public variables List / dimension variables viewable during program

execution
Dimension variables List / dimension variables not viewable during program
execution.
Define Aliases Assign aliases to variables.

Define Units Assign engineering units to variable (optional). Units

are strictly for documentation. The CR200(X) makes no
use of Units nor checks Unit accuracy.

Define data tables. Define stored data tables

Process/store trigger Set triggers when data should be stored. Triggers may
be a fixed interval, a condition, or both.

Table size Set the size of a data table

Processing of Data List data to be stored in the data table, e.g. samples,
averages, maxima, minima, etc.
Processes or calculations repeated during program
execution can be packaged in a subroutine and called
when needed rather than repeating the code each time.

Begin Program Begin Program defines the beginning of statements

defining datalogger actions.

Set scan interval The scan sets the interval for a series of measurements
Measurements Enter measurements to make
Processing Enter any additional processing

Call Data Table(s) Declared data tables must be called to process and
store data
Initiate controls Check measurements and initiate controls if necessary

NextScan Loop back to Set Scan and wait for the next scan

End Program End Program defines the ending of statements defining

datalogger actions.

CRBASIC EXAMPLE. Proper Program Structure (p. 73) demonstrates the

proper structure of a CRBASIC program.

72
 Section 9. Programming

CRBASIC EXAMPLE 3. Proper Program Structure

9.6 Declarations I - Single-line Declarations

Public variables, Dim variables, Constants, Units, Aliases, Data Tables and
Subroutines are declared at the beginning of a CRBASIC program. TABLE.
Rules for Names (p. 85) lists declaration names and allowed lengths

9.6.1 Variables
A variable is a packet of memory, given an alphanumeric name, through which
pass measurements and processing results during program execution. Variables
are declared either as Public or Dim at the discretion of the programmer. Public
variables can be viewed through software numeric monitors. Dim variables
cannot. Up to 128 public variables can be declared in a CR200(X) program and
up to 48 public variables declared in a CR200 program.

73
Section 9. Programming

Variable names can be up to 16 characters in length, but most variables should

be no more than 12 characters long. This allows for the 4 additional characters
that are added as a suffix to the variable name when it is output to a data table.

Variable names cannot start with a number or contain spaces or quote marks (“),
but can contain numbers and underscores (_). Several variables can be declared
on a single line, separated by commas:
Public RefTemp, AirTemp2, Batt_Volt

9.6.1.1 Arrays
When a variable is declared, several variables of the same root name can also be
declared. This is done by placing a suffix of "(x)" on the alphanumeric name,
which creates an array of x number of variables that differ only by the
incrementing number in the suffix. For example, rather than declaring four
similar variables as follows,
Public TempC1

Public TempC2

Public TempC3

Public TempC4

simply declare a variable array as shown below:

Public TempC(4),

This creates in memory the four variables TempC(1), TempC(2), TempC(3),

and TempC(4).

A variable array is useful in program operations that affect many variables in the
same way. CRBASIC EXAMPLE. Using a Variable Array in Calculations (p.
74) shows program code using a variable array to reduce the amount of code
required to convert four temperatures from Celsius degrees to Fahrenheit
degrees.

In this example a For/Next structure with a changing variable is used to specify

which elements of the array will have the logical operation applied to them. The
CRBASIC For/Next function will only operate on array elements that are clearly
specified and ignore the rest. If an array element is not specifically referenced,
e.g., TempC(), CRBASIC references only the first element of the array,
TempC(1).

74
 Section 9. Programming

CRBASIC EXAMPLE 4. Using a variable array in calculations

Public TempC(4)
Public TempF(4)
Dim T

BeginProg
Scan (1,Sec,0,0)
Therm109 (TempC(),4,1,Ex1,1.0,0)
For T = 1 To 4
TempF(T) = TempC(T) * 1.8 + 32
Next
NextScan
EndProg

9.6.1.2 Dimensions
The CR200(X) cannot use multi-dimensioned arrays.

9.6.1.3 Data Types

Variables, calculations, and stored data use IEEE4 4-byte floating point, a
binary format, with least significant bit first. Time is stored as integer seconds
since midnight, the start of 1990, which is also a 4-byte number.

CR200(X) IEEE4 Data

Word Size Range Resolution
4 bytes 24 bits (about 7 digits)
±1.8 x 10-38 to
±1.7 x 1038

9.6.1.4 Flags
Flags are a useful program control tool. While any variable can be used as a
flag, variables named "Flag" works best because datalogger support software
automatically adds variables call "Flag" to the Ports and Flags window. Because
the CR200(X) does not support the Boolean data type, the IIF function may be
used to distinguish between zero and non-zero values, effectively creating a
Boolean value. The value of -1(all bits on) is defined as true and the value of
zero (all bits off) is defined as false. CRBASIC EXAMPLE. Flag Declaration
and Use (p. 76) shows an example using a flag to initiate measurements.

75
Section 9. Programming

CRBASIC EXAMPLE 5. Flag Declaration and Use

Public batt_volt
Public Flag

BeginProg
Scan (1,Sec)
Flag = IIF (Flag=0,0,-1)
If Flag = true Then
Battery (batt_volt)
EndIf
NextScan
EndProg

9.6.2 Constants
CRBASIC EXAMPLE. Using the Const Declaration (p. 76) shows use of the
constant declaration. A constant can be declared at the beginning of a program
to assign an alphanumeric name to be used in place of a value so the program
can refer to the name rather than the value itself. Using a constant in place of a
value can make the program easier to read and modify, and more secure against
unintended changes.

Note Using all uppercase for constant names may make them easier to
recognize.

CRBASIC EXAMPLE 6. Using the Const Declaration

Public PTempC, PTempF
Const CtoF_Mult = 1.8
Const CtoF_Offset = 32

BeginProg
Scan (1,Sec,0,0)
Therm109 (PTempC,1,1,Ex1,1.0,0)
PTempF = PTempC * CtoF_Mult + CtoF_Offset
NextScan
EndProg

9.6.2.1 Predefined Constants

Several words are reserved for use by CRBASIC. These words cannot be used
as variable or table names in a program. Predefined constants include some
instruction names, as well as valid alphanumeric names for instruction
parameters. In general, instruction names should not be used as variable,
constant, or table names in a datalogger program, even if they are not
specifically listed as a predefined constant. If a predefined constant, such as
"Sub" is used as a variable in a program, an error similar to the following may
be, but is not always, displayed at CRBASIC pre-compile.
Compile Failed!
line 8: Sub is already is use as a predefined CONST.

76
 Section 9. Programming

TABLE. Predefined Constants and Reserved Words (p. 77) lists predefined
constants.

Table 7. Predefined Constants and Reserved Words

Case Day DO FOR
FALSE Hr If Msec
min mv2500 mv5000 PROG
SCAN Select SUB Sec
TABLE TRUE Usec Until
EX1 EX2 While

9.6.3 Alias and Unit Declarations

A variable can be assigned a second name, or alias, by which it can be called
throughout the program. Aliasing is particularly useful when using arrays.
Arrays are powerful features in complex programs, but place the same
appellation on a number of variables. The use of an alias allows the power of the
array to be used with the clarity of unique names.

Each variable can be assigned units to clarify the meaning. Units are not used
elsewhere in programming, but rather add meaning to resultant data table
headers.

CRBASIC EXAMPLE 7. Alias and Unit Declaration

Public TempC(2)

Alias TempC(1)=AirTempC
Alias TempC(2)=SoilTempC

Units TempC()=Deg_C

BeginProg
Scan (1,Sec)
Therm109 (TempC(),2,1,Ex1,1.0,0)
NextScan
EndProg

9.7 Declarations II - Declared Sequences

9.7.1 Data Tables
Data are stored in tables as directed by the CRBASIC program. A data table is
created by a series of CRBASIC instructions entered after variable declarations
but before the BeginProg instruction. These instructions include:

77
Section 9. Programming

DataTable ()
Output Trigger Condition(s)
Output Processing Instructions
EndTable

A data table is essentially a file that resides in CR200(X) memory. The file is
written to each time data are directed to that file. The trigger that initiates data
storage is tripped either by the CR200(X)'s clock, or by an event, such as a high
temperature. Up to 8 data tables can be created by the program for a CR200(X)
(4 data tables for a CR200). The data tables may store individual measurements,
individual calculated values, or summary data such as averages, maxima, or
minima to data tables.

Each data table is associated with overhead information that becomes part of the
ASCII file header (first few lines of the file) when data are downloaded to a PC.
Overhead information includes:

• table format

• datalogger type and operating system version,

• name of the CRBASIC program running in the datalogger

• name of the data table (limited to 16 characters)

• alphanumeric field names to attach at the head of data columns

This information is referred to as "table definitions."

TABLE. Typical Data Table (p. 79) shows a data file as it appears after the
associated data table has been downloaded from a CR200(X) programmed with
the code in CRBASIC EXAMPLE. Definition and Use of a Data Table (p. 79).
The data file consists of five or more lines. Each line consists of one or more
fields. The first four lines constitute the file header. Subsequent lines contain
data.

The first header line is the Environment Line. It consists of eight fields, listed in
TABLE. TOA5 Environment Line (p. 78).

Table 8. TOA5 Environment Line

Field Description Changed via
1 file type (always TOA5) No Change

2 station name DevConfig or Program

3 datalogger model No Change

4 datalogger serial number No Change

5 datalogger OS version Send New OS

6 datalogger program name Send New Program

7 datalogger program signature Send / Change Program

8 table name Change Program

78
 Section 9. Programming

The second header line reports field names. This line consists of a set of
comma-delimited strings that identify the name of individual fields as given in
the datalogger program. If the field is an element of an array, the name will be
followed by a comma separated list of subscripts within parentheses that
identifies the array index. For example, a variable named values that is declared
as an array of four elements in the datalogger program will be represented by
four field names: values(1), values(2), values(3), and values(4). Scalar variables
will not have array subscripts. There will be one value on this line for each
scalar value that is defined by the table. Default fieldnames are a combination
of the variable names (or alias) from which data are derived and a three letter
suffix. The suffix is an abbreviation of the data process that output the data to
storage. For example, “Avg” is the abbreviation for average. If the default
fieldnames are not acceptable to the programmer, FieldNames () instruction can
be used to customized fieldnames.

The third header line identifies engineering units for that field of data. These
units are declared in the “Define Units” section of the CRBASIC program, as
shown in CRBASIC EXAMPLE. Definition and Use of a Data Table (p. 79).
Units are strictly for documentation.

Subsequent lines are observed data and associated record keeping. The first
field being a timestamp, the second the record (data line) number.

Read More! See TABLE. Abbreviations of Names of Data Processes (p. 90) for
a list of default field names.

Table 9. Typical Data Table

TOA5 CR200(X) CR2xx No_SN CR200(X).Std.01 Data.CR2 4098 OneMin

TIMESTAMP RECORD BattV_Min T109_C_Avg Rain_mm_Tot

TS RN Volts Deg C Mm

Min Avg Tot

12/30/2010
12:59:00 PM 0 12.52359 -7.390147 0
12/30/2010
1:00:00 PM 1 12.56724 -6.412211 0
12/30/2010
1:01:00 PM 2 12.52695 -6.267832 0
12/30/2010
1:02:00 PM 3 12.56472 -6.298645 0

79
Section 9. Programming

CRBASIC EXAMPLE 8. Definition and Use of a Data Table

'Declare Variables
Public Batt_Volt
Public T109_C(2)

'Define Units
Units Batt_Volt=Volts
Units T109_C(2)=Deg C

'Define Data Tables

DataTable (OneMin,True,-1)
DataInterval (0,1,Min)
Average (1,Batt_Volt,False)
Average (2,T109_C(1),False)
EndTable

DataTable (Table1,True,-1)
DataInterval (0,1440,Min)
Minimum (1,Batt_Volt,False,False)
EndTable

'Main Program
BeginProg
Scan (5,Sec)

'Default Datalogger Battery Voltage measurement Batt_Volt:

Battery (Batt_Volt)

'109-L Thermistor measurements Temp_C:

Therm109(T109_C(),2,1,Ex1,1,0)

'Call Data Tables and Store Data

CallTable (OneMin)
CallTable (Table1)

NextScan
EndProg

As shown in CRBASIC EXAMPLE. Definition and Use of a Data Table (p. 79),
data table declaration begins with the DataTable () instruction and ends with the
EndTable () instruction. Between DataTable () and EndTable () are instructions
that define what data to store and under what conditions data are stored. A data
table must be called by the CRBASIC program for data storage processing to
occur. Typically, data tables are called by the CallTable () instruction once each
Scan.

9.7.1.1 DataTable () and EndTable () Instructions

The DataTable instruction has three parameters: a user-specified alphanumeric
name for the table (e.g., "OneMin"), a trigger condition (e.g., "True"), and the
size to make the table in RAM (e.g., auto allocated).

• Name-The table name can be any combination of numbers and letters up to

16 characters in length. The first character must be a letter.

80
 Section 9. Programming

• TrigVar-Controls whether or not data records are written to storage. Data

records are written to storage if TrigVar is true and if other conditions, such
as DataInterval (), are met. Default setting is -1 (True). TrigVar may be a
variable, expression, or constant. TrigVar does not control intermediate
processing. Intermediate processing is controlled by the disable variable,
DisableVar, which is a parameter in all output processing instructions (see
Output Processing Instructions (p. 81)).

Read More! TrigVar and DisableVar - Controlling Data Output and Output
Processing (p. 125) discusses the use of TrigVar and DisableVar in special
applications.

• Size-Table size is the number of records to store in a table before new data
begins overwriting old data. If "10" is entered, 10 records are stored in the
table -- the eleventh record will overwrite the first record. If "-1" is entered,
memory for the table is automatically allocated at the time the program
compiles. Auto allocation is preferred in most applications since the
CR200(X) sizes all tables such that they fill (and begin overwriting the
oldest data) at about the same time. Approximately 2K bytes of extra data
table space is allocated to minimize the possibility of new data over writing
the oldest data in ring memory when support software collects the oldest
data at the same time new data are written. These extra records are not
reported in the Status Table and are not reported to the support software and
so are not collected.

CRBASIC EXAMPLE. Definition and Use of a Data Table (p. 79) creates a data
table named "OneMin", stores data once a minute as defined by DataInterval (),
and retains the most recent records in SRAM, up to the automatically allocated
memory limit. DataRecordSize entries in the status table report allocated
memory in terms of number of records the tables hold.

9.7.1.2 DataInterval () Instruction

DataInterval () instructs the CR200(X) to write data records at the specified
interval. The interval is independent of the Scan () / NextScan interval;
however, it must be a multiple of the Scan () / NextScan interval. The data
interval must be at least one minute.

DataInterval does not override the trigger condition in the DataTable instruction.
If the trigger is not set always true by entering a constant, it is a condition that
must be met in addition to the time interval before data will be stored.

9.7.1.3 Output Processing Instructions

Data storage processing ("output processing") instructions determine what data
are stored in the data table. When a data table is called in the CRBASIC
program, data storage processing instructions process variables holding current
inputs or calculations. If trigger conditions are true, e.g. the required interval has
expired, processed values are stored ("output") in the data table. In CRBASIC
EXAMPLE. Definition and Use of a Data Table (p. 79), three averages are
stored.

81
Section 9. Programming

Consider the Average () instruction as an example of output processing

instructions. Average () stores the average of a variable over the data storage
output interval. Its parameters are:

• Reps-number of elements in the variable array for which to calculate

averages. Reps is set to 1 to average Batt_Volt, and set to 2 to average 2
thermistor temperatures, both of which reside in the variable array
"T109_C".

• Source-variable array to average. Variable arrays Batt_Volt (an array of 1)

and T109_C() (an array of 2) are used.

• DisableVar-controls whether or not a measurement or value is included in

an output processing function. A measurement or value will not be included
if the disable variable is true (≠ 0). For example, in the case of an Average
() output processing instruction, if, on a particular pass through the data
table, the Average () disable variable true, the value resident in the variable
to be averaged with not be included in the average. Program CRBASIC
EXAMPLE. Use of the Disable Variable has "False" entered for the disable
variable, so all readings are included in the averages; the average of
variable "Oscillator" does not include samples occurring when Flag 1 is
high, producing an average of 2, whereas, when Flag 1 is low (all samples
used), an average of 1.5 is calculated.

Read More! TrigVar and DisableVar - Controlling Data

Output and Output Processing (p. 125) discusses the
use of TrigVar and DisableVar in special applications.

CRBASIC EXAMPLE 9. Use of the Disable Variable

'Declare Variables and Units
Public Oscillator
Public Flag
Public DisableVar

'Define Data Tables

DataTable (OscAvgData,True,-1)
DataInterval (0,1,Min)
Average (1,Oscillator,DisableVar)
EndTable

'Main Program
BeginProg
Scan (1,Sec)

'Reset and Increment Counter

If Oscillator = 2 Then Oscillator = 0
Oscillator = Oscillator + 1

'Process and Control

If Oscillator = 1

82
 Section 9. Programming

If Flag = True Then

DisableVar = True
End If
Else
DisableVar = False
EndIf

'Call Data Tables and Store Data

CallTable (OscAvgData)

NextScan
EndProg

Read More! For a complete list of output processing instructions, see Data
Storage Output Processing (p. 94).

9.7.2 Subroutines
Subroutines allow a section of code to be called by multiple processes in the
main body of a program. Subroutines are defined before the main program body
of a program. Program CRBASIC EXAMPLE. Use of a Subroutine p. 83 shows
the use of a subroutine to repeatedly perform a calculation.

CRBASIC EXAMPLE 10. Use of a Subroutine

'Declare Variables and Units
Public Temp(4), I, Temp_F(4)

'Subroutine to convert temperature in degrees C to degrees F

Sub ConvertCtoF
For I = 1 to 4
Temp_F = Temp(I)*1.8 + 32
Next I
EndSub

'Main Program
BeginProg
Scan (1,Sec)
Therm109 (Temp(),4,1,Ex1,1.0,0)
'convert Temperatures to F using Subroutine:
Call ConvertCtoF
NextScan
EndProg

9.8 Program Execution Timing

CR200(X) programs are built within a Scan () / NextScan structure, with only
variable and data table declarations outside the Scan () / NextScan structure. In
these programs, Scan () / NextScan creates an infinite loop, each periodic pass
through the loop being synchronized to the CR200(X) clock. Scan () parameters
allow modification of the period. As shown in CRBASIC EXAMPLE. BeginProg
/ Scan / NextScan / EndProg Syntax (p. 84) , aside from declarations, the
CRBASIC program may be relatively short.

83
Section 9. Programming

Scan () determines how frequently instructions in the program are executed.

Scan has two parameters:

• Interval is the interval between scans.

• Units is the time unit for the interval. Interval is 1sec <= Interval <= 1 day.

CRBASIC EXAMPLE 11. BeginProg / Scan / NextScan / EndProg Syntax

BeginProg
Scan (1,Sec)
Therm109 (TempC(),2,1,Ex1,1.0,0)
CallTable Temp
NextScan
EndProg

9.9 Instructions
In addition to BASIC syntax, additional instructions are included in CRBASIC
to facilitate measurements and store data. CRBASIC Programming Instructions
(p. 93) contains a comprehensive list of these instructions.

9.9.1 Measurement and Data Storage Processing

CRBASIC instructions have been created for making measurements and storing
data. Measurement instructions set up CR200(X) hardware to make
measurements and store results in variables. Data storage instructions process
measurements into averages, maxima, minima, standard deviation, FFT, etc.

Each instruction is a keyword followed by a series of informational parameters

needed to complete the procedure. For example, the instruction for measuring
CR200(X) panel temperature is:
ExciteV (ExChan,ExmV)

"ExciteV" is the keyword. Two parameters follow: ExChan, the excitation

channel number to which the voltage should be applied; and ExmV, is the
excitation, in millivolts, to apply to the sensor. The syntax for applying 5000
millivolts to a sensor through excitation channel number 1 is shown in
CRBASIC EXAMPLE. Measurement Instruction Syntax (p. 84).

CRBASIC EXAMPLE 12. Measurement Instruction Syntax

ExciteV (ExChan,ExmV))

84
 Section 9. Programming

9.9.2 Parameter Types

Many instructions have parameters that allow different types of inputs. Common
input type prompts are listed below. Allowed input types are specifically
identified in the description of each instruction in CRBASIC Editor Help.

• Constant, or Expression that evaluates as a constant

• Variable

• Variable or Array

• Constant, Variable, or Expression

• Constant, Variable, Array, or Expression

• Name

• Name or list of Names

• Variable, or Expression

• Variable, Array, or Expression

9.9.3 Names in Parameters

TABLE. Rules for Names (p. 85) lists the maximum length and allowed
characters for the names for Variables, Arrays, Constants, etc. The CRBASIC
Editor pre-compiler will identify names that are too long or improperly
formatted.

Table 10. Rules for Names

Maximum Length
(number of characters)
Name for Allowed characters
Variable or Array 16 Letters A-Z, upper or lower case,
underscore "_", and numbers 0-9.
Constant 16 The name must start with a letter.
CRBASIC is not case sensitive
Units 10

Alias 16
Station Name 16

Data Table Name 16

Field name 16
Field Name 58
Description

85
Section 9. Programming

9.9.4 Expressions in Parameters

Read More! See Expressions (p. 87) for more information on expressions.

Many parameters allow the entry of expressions. If an expression is a

comparison, it will return -1 if the comparison is true and 0 if it is false (Logical
Expressions (p. 88)). CRBASIC EXAMPLE. Use of Expressions in Parameters
(p. 86) shows an example of the use of expressions in parameters in the
DataTable instruction, where the trigger condition is entered as an expression.
Suppose the variable TC is a thermistor temperature:

CRBASIC EXAMPLE 13. Use of Expressions in Parameters

'DataTable (Name, TrigVar, Size)
DataTable (Temp, TC > 100, 5000)

When the trigger is "TC > 100", a TC temperature > 100 will set the trigger to
true and data is stored.

9.9.5 Arrays of Multipliers and Offsets

A single measurement instruction can measure a series of sensors and apply
individual calibration factors to each sensor as shown in CRBASIC EXAMPLE.
Use of Arrays as Multipliers and Offsets (p. 86). Storing calibration factors in
variable arrays, and placing the array variables in the multiplier and offset
parameters of the measurement instruction, makes this possible. The
measurement instruction uses repetitions to implement this feature by stepping
through the multiplier and offset arrays as it steps through the measurement
input channels. If the multiplier and offset are not arrays, the same multiplier
and offset are used for each repetition.

CRBASIC EXAMPLE 14. Use of Arrays as Multipliers and Offsets

Public Pressure(3), Mult(3), Offset(3)

DataTable (AvgPress,1,-1)
DataInterval (0,60,Min)
Average (3,Pressure(),IEEE4,0)
EndTable

BeginProg
'Calibration Factors:
Mult(1)=0.123 : Offset(1)=0.23
Mult(2)=0.115 : Offset(2)=0.234
Mult(3)=0.114 : Offset(3)=0.224

Scan (1,Sec)
'VoltSe instruction using array of multipliers and offsets:
VoltSe (Pressure(),3,1,Mult(),Offset())
CallTable AvgPress
NextScan
EndProg

86
 Section 9. Programming

Read More! More information is available in CRBASIC Editor Help topic

"Multipliers and Offsets with Repetitions".

9.10 Expressions
An expression is a series of words, operators, or numbers that produce a value
or result. Expressions are evaluated expression from left to right, with deference
to precedence rules.

Two types of expressions, mathematical and programming, are used in

CRBASIC. A useful property of expressions in CRBASIC is that they are
equivalent to and often interchangeable with their results.

Consider the expressions:

x = (z * 1.8) + 32 (a mathematical expression)

If x = 23 then y = 5 (programming expression)

The variable x can be omitted and the expressions combined and written as:
If (z * 1.8 + 32 = 23) then y = 5

Replacing the result with the expression should be done judiciously and with the
realization that doing so may make program code more difficult to decipher.

9.10.1 Floating Point Arithmetic

Variables and calculations are performed internally in single precision IEEE4 4-
byte floating point, a binary format.

Floating point arithmetic is common in many electronic computational systems,

but it has pitfalls high-level programmers should be aware of. Several sources
discuss floating point arithmetic thoroughly. One readily available source is the
topic "Floating Point" at Wikipedia.org. In summary, CR200(X) programmers
should consider at least the following:

• Floating point numbers do not perfectly mimic real numbers.

• Floating point arithmetic does not perfectly mimic true arithmetic.

• Avoid use of equality in conditional statements. Use >= and <= instead. For
example, use "If X => Y, then do" rather than using, "If X = Y, then do".

9.10.2 Mathematical Operations

Mathematical operations are written out much as they are algebraically. For
example, to convert Celsius temperature to Fahrenheit, the syntax is:
TempF = TempC * 1.8 + 32

87
Section 9. Programming

CRBASIC EXAMPLE. Use of Variable Arrays to conserve Code p. 88 shows

example code to convert five temperatures in a variable array from C to F:

CRBASIC EXAMPLE 15. Use of Variable Arrays to Conserve Code Space

For I = 1 to 5
TempC(I) = TempC(I) * 1.8 + 32
Next I

9.10.3 Logical Expressions

Measurements can indicate absence or presence of an event. For example, an
RH measurement of 100% indicates a condensation event such as fog, rain, or
dew. The CR200(X) can render events into binary form for further processing,
i.e., events can either be TRUE, indicating the condition occurred or is
occurring, or FALSE, indicating the condition has not yet occurred or is over.

Several words are commonly interchanged with True / False such as High /
Low, On / Off, Yes / No, Set / Reset, Trigger / Do Not
Trigger. The CR200(X) understands only True / False or -1 /
0, however. The CR200(X) represents "true" with "-1"
because AND / OR operators are the same for logical
statements and binary bitwise comparisons.

In the binary number system internal to the CR200(X), "-1" is expressed with
all bits equal to 1 (11111111). "0" has all bits equal to 0
(00000000). When -1 is ANDed with any other number, the
result is the other number. This ensures that if the other
number is non-zero (true), the result is non-zero.

Using TRUE or FALSE conditions with logic operators such as AND and OR,
logical expressions can be encoded into a CR200(X) to perform three general
logic functions, facilitating conditional processing and control applications.

1. Evaluate an expression, then take one path or action if the expression is

true (= -1), and / or another path or action if the expression is false (=
0).

2. Evaluate multiple expressions linked with AND or OR.

3. Evaluate multiple and / or links.

88
 Section 9. Programming

The following commands and logical operators are used to construct logical
expressions. CRBASIC EXAMPLE. Logical Expression Examples p. 89
demonstrate some logical expressions.

• IF

• AND

• OR

• NOT

• XOR

• IIF

Table 11. Logical Expression Examples

If X >= 5 then Y = 0
Sets the variable Y to 0 if the expression "X >= 5" is true, i.e. if X is greater than or equal to 5. The CR200(X) evaluates
the expression (X >= 5) and registers in system memory a -1 if the expression is true, or a 0 if the expression is false.
If X >= 5 OR Z = 2 then Y = 0
Sets Y = 0 if either X >= 5 or Z = 2 is true.
If X >= 5 AND Z = 2 then Y = 0
Sets Y = 0 only if both X >= 5 and Z = 2 are true.
If 6 then Y = 0.
"If 6" is true since "6" (a non-zero number) is returned, so Y is set to 0 every time the statement is executed.
If 0 then Y = 0.
"If 0" is false since "0" is returned, so Y will never be set to 0 by this statement.
Z = (X > Y).
Z will equal -1 if X > Y, or Z will equal 0 if X <= Y.
The NOT operator simply complements every bit in the word. A Boolean can only be 0 or have all of its bits set to 1.
Complementing a Boolean will turn TRUE (all bits set) to FALSE (all bits complemented to 0). Since the CR200(X)
cannot declare a variable to be a Boolean data type, IIF is used to force the logical results to either 0 or -1.
Example Program

'(a AND b) = (26 AND 26) = (&b11010 AND &b11010) =

'&b11010. NOT (&b11010) yields &b00101.

'This is non-zero, so when converted to a

'BOOLEAN, it becomes TRUE.
Public a
Public b
Public is_true
Public not_is_true
Public not_a_and_b
BeginProg
a = 26
b = a
Scan (1,Sec)
is_true = IIF(a AND b = 0,0,-1) 'This evaluates to TRUE.
not_is_true = IIF(NOT (is_true) = 0,0,-1) 'This evaluates to FALSE.
not_a_and_b = IIF(NOT (a AND b) = 0,0,-1) 'This evaluates to TRUE!
NextScan
EndProg

89
Section 9. Programming

9.11 Program Access to Data Tables

CRBASIC has syntax provisions facilitating access to data in tables or
information relating to a table. The syntax is entered directly into the CRBASIC
program through a variable name. The general form is:

"TableName.FieldName_Prc (Fieldname Index, Records Back)".

Where:

• TableName: name of the data table

• FieldName: name of the variable from which the processed value is derived

• Prc: Abbreviation of the name of the data process used. See TABLE.
Abbreviations of Names of Data Processes p. 90 for a complete list of these
abbreviations-not needed for values from Status or Public tables.

• Fieldname Index: Array element number (optional)

• Records Back: How far back into the table to go to get the value (optional)

Table 12. Abbreviations of Names of Data

Processes
Abbreviation Process Name
Tot Totalize
Avg Average
Max Maximum
Min Minimum

Std Standard Deviation

Sample

WVc WindVector

ETsz ET
RSo Solar Radiation (from ET)
TMx Time of Max

TMn Time of Min

For instance, to access the number of watchdog errors, use the

"Status.WatchDogCnt," where "Status" is the table name, and "WatchDogCnt"
is the field name.

90
 Section 9. Programming

Five special variable names are used to access information about a table:

• FieldName

• Output

• Record

• TableSize

• TimeStamp

Consult CRBASIC Editor Help Index topic "DataTable access" for complete
information.

91
Section 9. Programming

92
Section 10. CRBASIC Programming
Instructions
Read More! Parameter listings, application information, and code examples are
available in CRBASIC Editor Help. CRBASIC Editor is part of LoggerNet /
PC400 / RTDAQ.

Select instructions are explained more fully, some with example code, in
Programming Resource Library (p. 109). Example code is throughout the
CR200(X) manual. Refer to the table of contents Example index.

10.1 Program Declarations

10.1.1 Variable Declarations & Modifiers
Alias
Assigns a second name to a variable.
Syntax
Alias [variable] = [alias name]

Dim
Declares and dimensions private variables. Dimensions are optional.
Syntax
Dim [variable name (x,y,z)]

Public
Declares and dimensions public variables. Dimensions are optional.
Syntax
Public [variable name (x,y,z)]

Units
Assigns a unit name to a field associated with a variable.
Syntax
Units [variable] = [unit name]

10.1.2 Constant Declarations

Const
Declares symbolic constants for use in place of numeric entries.
Syntax
Const [constant name] = [value or expression]

93
Section 10. CRBASIC Programming Instructions

10.2 Data Table Declarations

DataTable … EndTable
Mark the beginning and end of a data table.
Syntax
DataTable (Name, TrigVar, Size)
[data table modifiers]
[on-line storage destinations]
[output processing instructions]
EndTable

10.2.1 Data Table Modifiers

DataInterval
Sets the time interval for an output table.
Syntax
DataInterval (TintoInt, Interval, Units,)

10.2.2 Data Storage Output Processing

FieldNames
Immediately follows an output processing instruction to change default field
names.
Syntax
FieldNames ("Fieldname1 : Description1, Fieldname2
: Description2…")

10.2.2.1 Single-Source
Average
Stores the average value over the output interval for the source variable or each
element of the array specified.
Syntax
Average (Reps, Source, DisableVar)

Maximum
Stores the maximum value over the output interval.
Syntax
Maximum (Reps, Source, DisableVar, Time)

Minimum
Stores the minimum value over the output interval.
Syntax
Minimum (Reps, Source, DisableVar, Time)

Sample
Stores the current value at the time of output.
Syntax
Sample (Reps, Source)

94
 Section 10. CRBASIC Programming Instructions

StdDev
Calculates the standard deviation over the output interval.
Syntax
StdDev (Reps, Source, DisableVar)

Totalize
Sums the total over the output interval.
Syntax
Totalize (Reps, Source, DisableVar)

10.2.2.2 Multiple-Source
ETo
Stores evapotranspiration (ETo) and other meteorological data. Most suitable
for output intervals of less than 24 hours.
Syntax
ETo (Temp, RH, u2, Rs, Longitude, Latitude,
Altitude, DisableVar)

EToDaily
Stores evapotranspiration (ETo) and other meteorological data. Most suitable
for output intervals 24 hours or more.
Syntax
EToDaily (Temp, RH, u2, Rs, Longitude, Latitude,
Altitude, DisableVar)

WindVector
Processes wind speed and direction from either polar or orthogonal sensors. To
save processing time, only calculations resulting in the requested data are
performed.
Syntax
WindVector (Repetitions, Speed/East,
Direction/North, DisableVar, SensorType,
WVOutputOpt)

Read More! See Wind Vector (p. 120).

10.3 Single Execution at Compile

Sub, ExitSub, EndSub
Declares the name, variables, and code that form a Subroutine. Argument list is
optional. ExitSub is optional.
Syntax
Sub subname (argument list)

[statement block]

ExitSub

[statement block]

EndSub

95
Section 10. CRBASIC Programming Instructions

10.4 Program Control Instructions

10.4.1 Common Controls
BeginProg … EndProg
Mark the beginning and end of a program.
Syntax
BeginProg
Program Code
EndProg

Call
Transfers program control from the main program to a subroutine.
Syntax
Call subname

CallTable
Calls a data table, typically for output processing.
Syntax
CallTable [TableName]

Delay
Delays the program.
Syntax
Delay (Delay, Units)

Do … While ... Until ... ExitDo ... Loop

Repeats a block of statements while a condition is true or until a condition
becomes true.
Syntax
Do [{While | Until} condition]
[statementblock]
[ExitDo]
[statementblock]
Loop
-or-
Do
[statementblock]
[ExitDo]
[statementblock]
Loop [{While | Until} condition]
For ... To ... Step ... ExitFor ... Next
Repeats a group of instructions a specified number of times.
Syntax
For counter = start To end [ Step increment ]
[statementblock]
[ExitFor]
[statementblock]
Next [counter [, counter][, ...]]

96
 Section 10. CRBASIC Programming Instructions

If ... Then ... Else … ElseIf ... EndIf

Allows conditional execution, based on the evaluation of an expression. Else is
optional. ElseIf is optional (EndSelect and EndIf call the same function).
Syntax
If [condition] Then [thenstatements] Else [elsestatements]
-or-

If [condition 1] Then
[then statements]
ElseIf [condition 2] Then
[elseif then statements]
Else
[else statements]
EndIf

InterruptSequence
Specifies code to run when an interrupt condition occurs.
Syntax
InterruptSequence

LoggerIdentify
Sets an identification string in the datalogger that will be returned when another
string is sent to the datalogger.
Syntax
LoggernetIdentify (RequestString",ReturnString")

Scan … NextScan
Establishes the program scan rate. ExitScan and ContinueScan are optional.
Syntax
Scan (Interval, Units)
...
Next Scan
...
ContinueScan
...
Next Scan

ScanLEDOff
Turns off the LED on the datalogger's front case that indicates a program scan is
occurring.

Select Case … Case … Case Is … Case Else … EndSelect

Executes one of several statement blocks depending on the value of an
expression. CaseElse is optional. (EndSelect and EndIf call the same CR200(X)
function).
Syntax
Select Case testexpression
Case [expression 1]
[statement block 1]
Case [expression 2]
[statement block 2]
Case Is [expression fragment]
Case Else
[statement block 3]
EndSelect

97
Section 10. CRBASIC Programming Instructions

While…Wend
Execute a series of statements in a loop as long as a given condition is true.
Syntax
While Condition
[StatementBlock]
Wend

10.5 Measurement Instructions

10.5.1 Diagnostics
Battery
Measures input voltage.
Syntax
Battery (Dest)

10.5.2 Voltage
VoltSe
Measures the voltage at a single-ended input with respect to ground.
Syntax
VoltSe (Dest, Reps, SEChan, Mult, Offset)

Read More! See Bridge Resistance Measurements (p. 41).

ExDelSE
Applies an excitation voltage, delays for a specified period of time, and makes a
single-ended voltage measurement. Allowable excitation voltages are +2500mV
and +5000mV.
Syntax
ExDelSE (Dest, Reps, SEChan, ExChan, ExmV, Delay,
Mult, Offset)

Therm109
Measures a Campbell Scientific 109 thermistor
Syntax
Therm109 (Dest, Reps, SEChan, Vx/ExChan,
SettlingTime, Integ, Mult, Offset)

10.5.3 Pulse
Read More! See Pulse Count Measurement (p. 42).

Note Pull-up resistors are required when using digital I/O (control) ports for
pulse input (Pulse Input on Digital I/O Channels C1 - C2 (p. 45)).

98
 Section 10. CRBASIC Programming Instructions

PulseCount
Measures number or frequency of voltages pulses on a pulse channel.
Syntax
PulseCount (Dest, PChan, PConfig, POption, Mult,
Offset)

10.5.4 Digital I/O

AnalogPortGet
Configures an analog port as a digital input and stores the status of the input in a
variable.
Syntax
AnalogPortGet (Dest, Port)

AnalogPortSet
Configures an analog port as a digital output and sets the port either high or low.
Syntax
AnalogPortSet (Port, State)

PeriodAvg
Measures the period of a signal on any single-ended voltage input channel.
Syntax
PeriodAvg (Dest, SEChan, PAOption, Cycles,
Timeout, Port, Mult, Offset)

PortGet
Reads the status of a control port.
Syntax
PortGet (Dest, Port)

PortSet
Sets the specified port high or low.
Syntax
PortSet (Port, State)

10.5.5 SDI-12
Read More! See SDI-12 Sensor Support (p. 112).

SDI12Recorder
The SDI12Recorder instruction is used to retrieve the results from an SDI-12
sensor.
Syntax
SDI12Recorder (Dest, Outstring, Multiplier,
Offset)

SDI12SensorSetup
Sets up the datalogger to act as an SDI12 sensor. Used together with
SDI12SensorResponse.

99
Section 10. CRBASIC Programming Instructions

SDI12SensorResponse
Holds the source of the data to send to the SDI12 recorder.
Syntax
SDI12SensorSetup (Repetitions, SDIPort, SDIAddress,
ResponseTime)
SDI12SensorResponse (SDI12Source)

10.6 Processing and Math Instructions

10.6.1 Mathematical Operators
^ Raise to Power.

* Multiply

/ Divide

+ Add

- Subtract

= Equals

<> Not Equal

> Greater Than

< Less Than

>= Greater Than or Equal

<= Less Than or Equal

10.6.2 Logical Operators

AND
Used to perform a logical conjunction on two expressions.
Syntax
result = expr1 AND expr2

IIF
Evaluates a variable or expression and returns one of two results based on the
outcome of that evaluation.
Syntax
Result = IIF (Expression, TrueValue, FalseValue)

NOT
Performs a logical negation on an expression.
Syntax
result = NOT expression

100
 Section 10. CRBASIC Programming Instructions

OR
Used to perform a logical disjunction on two expressions.
Syntax
result = expr1 OR expr2

XOR
Performs a logical exclusion on two expressions.
Syntax
result = expr1 XOR expr2

10.6.3 Trigonometric Functions

10.6.3.1 Derived Functions
TABLE. Derived Trigonometric Functions (p. 101) is a list of trigonometric
functions that can be derived from functions intrinsic to CRBASIC.

Table 13. Derived Trigonometric Functions

Function CRBASIC Equivalent
Secant Sec = 1 / Cos(X)
Cosecant Cosec = 1 / Sin(X)
Cotangent Cotan = 1 / Tan(X)
Inverse Secant Arcsec = Atn(X / Sqr(X * X - 1)) + Sgn(Sgn(X) - 1) * 1.5708
Inverse Cosecant Arccosec = Atn(X / Sqr(X * X - 1)) + (Sgn(X) - 1) * 1.5708

Inverse Cotangent Arccotan = Atn(X) + 1.5708

Hyperbolic Secant HSec = 2 / (Exp(X) + Exp(-X))
Hyperbolic Cosecant HCosec = 2 / (Exp(X) - Exp(-X))
Hyperbolic Cotangent HCotan = (Exp(X) + Exp(-X)) / (Exp(X) - Exp(-X))
Inverse Hyperbolic Sine HArcsin = Log(X + Sqr(X * X + 1))
Inverse Hyperbolic Cosine HArccos = Log(X + Sqr(X * X - 1))
Inverse Hyperbolic Tangent HArctan = Log((1 + X) / (1 - X)) / 2
Inverse Hyperbolic Secant HArcsec = Log((Sqr(-X * X + 1) + 1) / X)
Inverse Hyperbolic Cosecant HArccosec = Log((Sgn(X) * Sqr(X * X + 1) + 1) / X)
Inverse Hyperbolic Cotangent HArccotan = Log((X + 1) / (X - 1)) / 2

10.6.3.2 Intrinsic Functions

ACOS
Returns the arc cosine of a number.
Syntax
x = ACOS(source)

101
Section 10. CRBASIC Programming Instructions

ASIN
The ASIN function returns the arc sin of a number.
Syntax
x = ASIN(source)

ATN
Returns the arctangent of a number.
Syntax
x = ATN(source)

ATN2
Returns the arctangent of y / x.
Syntax
x = ATN(y , x)

COS
Returns the cosine of an angle specified in radians.
Syntax
x = COS(source)

SIN
Returns the sine of an angle.
Syntax
x = SIN(source)

TAN
Returns the tangent of an angle.
Syntax
x = TAN(source)

10.6.4 Arithmetic Functions

ABS
Returns the absolute value of a number.
Syntax
x = ABS(source)

EXP
Returns e (the base of natural logarithms) raised to a power
Syntax
x = EXP(source)

FRAC
Returns the fractional part of a number.
Syntax
x = FRAC(source)

INT or FIX
Return the integer portion of a number.
Syntax
x = INT(source)
x = Fix(source)

102
 Section 10. CRBASIC Programming Instructions

LOG
Returns the natural logarithm of a number. Ln and Log perform the same
function.
Syntax
x = LOG(source)
x = LN(source)

Note LOGN = LOG(X) / LOG(N)

LOG10
The LOG10 function returns the base 10 logarithm of a number.
Syntax
x = LOG10 (number)

MOD
Divides two numbers and returns only the remainder.
Syntax
result = operand1 MOD operand2

RectPolar
Converts from rectangular to polar coordinates.
Syntax
RectPolar (Dest, Source)

SGN
Finds the sign value of a number.
Syntax
x = SGN(source)

Sqr
Returns the square root of a number.
Syntax
x = SQR(number)

10.6.5 Spatial Processing

AvgSpa
Computes the spatial average of the values in the source array.
Syntax
AvgSpa (Dest, Swath, Source)

CovSpa
Computes the spatial covariance of sets of data.
Syntax
CovSpa (Dest, NumOfCov, SizeOfSets, CoreArray,
DatArray)

MaxSpa
Finds the maximum value in an array.
Syntax
MaxSpa (Dest, Swath, Source)

103
Section 10. CRBASIC Programming Instructions

MinSpa
Finds the minimum value in an array.
Syntax
MinSpa (Dest, Swath, Source)

RMSSpa
Computes the RMS (root mean square) value of an array.
Syntax
RMSSpa (Dest, Swath, Source)

StdDevSpa
Used to find the standard deviation of an array.
Syntax
StdDevSpa (Dest, Swath, Source)

10.6.6 Other Functions

Randomize
Initializes the random-number generator.
Syntax
Randomize (source)

RND
Generates a random number.
Syntax
RND (source)

10.7 Clock Functions

ClockSet
Sets the datalogger clock from the values in an array
Syntax
ClockSet (Source)

IfTime
Returns a number indicating True (-1) or False (0) based on the datalogger's
real-time clock.
Syntax
If (IfTime (TintoInt, Interval, Units)) Then
-or-
Variable = IfTime (TintoInt, Interval, Units)
RealTime
Parses year, month, day, hour, minute, second, micro-second, day of week,
and/or day of year from the datalogger clock.
Syntax
RealTime (Dest)

Ticker250ms
Stores the running total of a 250ms system timer.
Syntax
Ticker250ms (Destination)

104
 Section 10. CRBASIC Programming Instructions

10.8 Serial Input / Output

Print
Sends the values from program variables or other characters out through a
communications port.
Syntax
Print (PrintPort, PrintBaud, PrintParams)

SerialInput
Reads a serial sensor connected to the CR200(X)'s RS232 port.
Syntax
SerialInput (Dest, Max_Values, Termination_Char,
FilterString)

10.9 Peer-to-Peer PakBus Communications

Read More! See PakBus Overview (p. 133) for more information. Also see
Campbell Scientific PakBus® Networking Guide available at
www.campbellsci.com.

Peer-to-peer PakBus® instructions enable the datalogger to communicate with

other PakBus® devices. Instructions specify a COM port and a PakBus®
address. If the route to the device is not yet known, a direct route through the
specified COM port is first tried.

The PakBus® Address is a variable that can be used in CRBASIC like any other
variable.

The ComPort specifies the communications port that will be used to

communicate with the host device. Enter one of the following commands:

• RF

• RS232

In general, PakBus® instructions write a result code to a variable indicating

success or failure. Success sets the result code to 0. Otherwise, the result code
increments. If communication succeeds but an error is detected, a negative result
code is set. See CRBASIC Editor Help for an explanation of error codes.

The Timeout parameter in these instructions is in units of 0.01 seconds. If 0 is

used, then the default timeout defined by the time of the best route is used. Use
PakBusGraph "Hop Metrics" to calculate this time.

These communication instructions wait for a response or timeout before the

program moves on to the next instruction.

105
Section 10. CRBASIC Programming Instructions

GetValue
Retrieves values from a variable in a data table of a PakBus datalogger.
Syntax
GetVariables (ResultCode, ComPort, NeighborAddr,
PakBusAddr, Security, TimeOut, "TableName",
"FieldName", Variable, Swath)

ReadSendGetInfo
Returns the interval and offset for the SendGetData instruction.
Syntax
ReadSendGetInfo (Dest, Port)

SendData
Sends the most recent record from a data table to a remote PakBus device.
Syntax
SendData (ComPort, NeighborAddr, PakBusAddr,
DataTable)

Note: For the CR200 series, this instruction is supported

only in a special 'S' operating system, version 5.10 and
greater (V06S).

SendGetData
Sends an array of values from a remote CR200(X) to a host datalogger and/or
retrieves an array of data from the host datalogger.
Syntax
SendGetData(ResponseDest, Control, Measurement,
Port, HostAddr, RepeatAddr, Security)

SetValue
Sends values from one or more variables to a remote datalogger's Public table.
Syntax
SetValue (ResponseDest, Source, Swath, RemoteVar,
Port, RemoteAddr, RepeatAddr, Security)

TimeUntilTransmit
The TimeUntilTransmit instruction returns the time remaining, in seconds,
before communication with the host datalogger.
Syntax
TimeUntilTransmit (port)

10.10 Data Table Access and Management

Commands to access and manage data stored in data tables, including Public
and Status tables.
SetStatus
Changes the value for a setting in the datalogger Status table.
Syntax
SetStatus ("FieldName", Value)

106
 Section 10. CRBASIC Programming Instructions

TableName.FieldName
Accesses a specific field from a record in a table
Syntax
TableName.FieldName (FieldNameIndex, RecordsBack)

TableName.Output
Determine if data was written to a specific DataTable the last time the
DataTable was called.
Syntax
TableName.Output (1,1)

TableName.Record
Determines the record number of a specific DataTable record.
Syntax
TableName.Record (1,n)

TableName.TableSize
Returns the number of records allocated for a data table
Syntax
TableName.TableSize (1,1)

TableName.TimeStamp
Returns the time into an interval or a timestamp for a record in a specific
DataTable.
Syntax
TableName.TimeStamp (m,n)

10.11 SCADA
Read More! See Modbus (p. 139).

Note: These instructions are supported only in a special operating system

version 'M' for CR200 series dataloggers. That operating system must be loaded
on the datalogger and the program compiled with the matching compiler to use
ModBusMaster and ModBusSlave. No special operating system is required for
CR200(X) series dataloggers.

ModBusMaster
Sets up a datalogger as a ModBus master to send or retrieve data from a
ModBus slave.
Syntax
ModBusMaster (ResultCode, ComPort, BaudRate,
ModBusAddr, Function, Variable, Start, Length,
Tries, TimeOut)

ModBusSlave
Sets up a datalogger as a ModBus slave device.
Syntax
ModBusSlave (ComPort, BaudRate, ModBusAddr,
ModBusVariable, BooleanVariable, ByteOrder,
Offset)

107
Section 10. CRBASIC Programming Instructions

10.12 Satellite Systems Programming

Instructions for GOES. Refer to satellite transmitter manuals available at
www.campbellsci.com.

10.12.1 GOES
The CR295 and CR295X dataloggers support communication through Campbell
Scientific’s TX312 or HDR GOES satellite transmitters. The CR295(X) has an
extra 9-pin serial port. The CR295 requires a special operating system and does
not support radio telemetry or calculation of evapotranspiration and is not CE
compliant. The CR295X has the same operating system and expanded
capabilities as other CR200(X) series dataloggers.

CRBASIC instructions used by the CR295(X) are:

GOESData
Sends data to a CSI GOES satellite data transmitter.
Syntax
GOESData (Dest, Table, TableOption, BufferControl,
DataFormat)

GOESGPS
Stores GPS data from the satellite into two variable arrays.
Syntax
GOESGPS (GoesArray1(6), GoesArray2(7))

GOESSetup
Programs the GOES transmitter for communication with the satellite.
Syntax
GOESSetup (ResultCode, PlatformID, MsgWindow,
STChannel, STBaud, RChannel, RBaud, STInterval,
STOffset, RInterval)

GOESStatus
Requests status and diagnostic information from a CSI GOES satellite
transmitter.
Syntax
GOESStatus (Dest, StatusCommand)

108
Section 11. Programming Resource
Library
11.1 Remote Sensor Interface
The CR200(X) is frequently used as a remote sensor interface for a “Host”
datalogger. Typically, the host datalogger and the sensor(s) (CR200(X)) will
have programs that will enable the sensors to operate with the minimum
quiescent current drain (110 µa). These programs synchronize the CR200(X)
sensors so that they are reporting back the data in designated time slots.

For applications demanding more frequent communication, the get/set variable

instructions in the host datalogger can be used with CR200(X) sensors that are
configured for higher current drain (250 µa for 8 second response; 20 ma for 1
second response).

In the lowest power, synchronized mode, the CR200(X) always initiates

communication. Except when it wakes up to send data, its radio is off, drawing
no power. The host datalogger’s radio will be in a fully on position during the
period of expected sensor communication, ready to receive and respond
instantly.

CRBASIC EXAMPLE 16. Example Wireless Sensor Program For CR200(X)

Const MT = 20 'Measurement Time (secs) SDI-12 in this Case takes 20 seconds
Const Port = 1 '1 = Radio, 2 = RS-232 To send out data
Const RouterAddr = 1 'the PakBus address of a router, in this Case the same as Host
Const HostAddr = 1 'the PakBus address of the Host datalogger
Const NumVals = 8 '8 Measurements
Const Security = 0 'use non zero If Host datalogger has Security set
Const NumControl = 4

Public Measurements(NumVals) 'sensor values To send

Public Control(NumControl) 'Control values returned from Host

BeginProg
Scan(1, sec)
If TimeUntilTransmit(Port)=MT Then 'If it Is time To measure start Measurement
'applicable Measurements that take MT seconds inserted here
EndIf
NextScan
EndProg

TimeUntilTransmit(port) is a function that returns the number of seconds before

it is time to communicate. It will use information retrieved from the datalogger
to determine the time remaining before its communication time slot.

SendGetData will output an array of measurements to the Host datalogger and

retrieve a time slot, a clock setting, and optionally an array of data from the Host

109
Section 11. Programming Resource Library

Either the output array or the input array or both can be specified as 0 meaning
no data flow in the corresponding direction.

The HostAddr parameter is the PakBus Address of the master of the network,
the destination of the sensor’s data. The RouterAddr is the PakBus Address of a
router if the distance is too far to reach the Host directly. Typically a router will
not be present so this address with be identical to the HostAddr. If it is 0, then
the system will automatically find a neighbor it can route through.

All communication with the host datalogger (CR800, CR1000 or CR3000) takes
place through the SendGetData() instruction. When SendGetData() is included
in the CR200 CRBASIC program, the CR200 calls the host approximately every
60 seconds with a random time into interval setting to establish the first
connection. At first connection, the CR200 sends a variable array to the host,
retrieves a variable array from the host, and retrieves a call time slot and a clock
synchronization setting. Thereafter, the CR200 calls at the appointed time slot.

11.2 Radio Power Minimization

Power settings on the CR200(X) radio are used to optimize the current drain of
the system. The radio can be set to be always on, power up once a second or
every 8 seconds, or be turned on by the CR200(X) program. When the status
table field RF_ForceOn is set true under program control, the radio is on only as
long as necessary for data transmission and receiving. This provides the lowest
power usage by the radio.

RF_ForceOn can be controlled with table access syntax

(SetStatus(Rf_ForceOn,1) for example) or it is controlled by the instruction
SendGetData() as shown in the following example p. 111.

A CR1000 datalogger with PakBus address 2 and a RF401 radio is configured

as the “master”. It sends a Network() command every 5 minutes to synchronize
the radio transmission. A CR206X datalogger with PakBus address 3 measures
its sensors every 15 minutes and runs a countdown using TimeUntilTransmit().
When the countdown reaches zero, the CR206X powers its radio and transmits
data to the CR1000 as well as receiving the CR1000 battery voltage.

The radio address and hop sequence of the CR206X must match the same
settings in the RF401.

110
 Section 11. Programming Resource Library

CRBASIC EXAMPLE 17. CRBASIC EXAMPLE. Radio Power Minimization Program

Examples
‘Pin Enabled Radio Program Example Program for CR1000
'Pakbus Address = 2

Public Rx(6), Tx, Result

Alias Rx(1)=VWC_1: Alias Rx(2)=VWC_2 ‘Alias used to give meaningful names to
Alias Rx(3)=VWC_3: Alias Rx(4)=VWC_4 ‘data received from remote datalogger
Alias Rx(5)=Tsoil_C: Alias Rx(6)=Batt_206_V
Alias Tx=Batt_CR1K_V

DataTable (Test,1,-1)
DataInterval (0,60,Min,10)
Average (6,Rx(),FP2,False)
Minimum (1,Batt_CR1K_V,FP2,False,False)
EndTable

BeginProg
Scan (15,Sec,0,0)
Battery (Batt_CR1K_V)
CallTable Test
NextScan

'Send Network command every 5 minutes

SlowSequence
Scan (5,Min,0,0)
Network (Result,1,3,15,60,0,6,Rx(),1,Tx)
NextScan
EndProg

------------------------------------------------------------------------------------------

'Pin Enabled Radio Example for CR206X

'Pakbus address 3
Public Time, TxData(6)
Public Period_uS(4), Response, Rx
Alias TxData(1)=VWC_1: Alias TxData(2)=VWC_2: Alias TxData(3)=VWC_3
Alias TxData(4)=VWC_4: Alias TxData(5)=T109_C: Alias TxData(6)=Batt_Volt
Alias Rx = CR1K_Batt_Volt

Dim LoopCnt
Units Batt_Volt=Volts
Units Period_uS()=uSec
Units T109_C=Deg C

DataTable(VWC_pin,True,-1)
DataInterval(0,60,Min)
Average(5,TxData(),False)
Minimum (1,Batt_Volt,False,0)
EndTable

BeginProg
SetStatus (RfPwrMode,RFpinEn) 'Configure CR200(X) power mode to pin enabled
Scan(1,sec)
If IfTime (0,15,Min) Then 'Take readings every 15 minutes
Battery(Batt_Volt)
Therm109(T109_C,1,5,1,1.0,0.0)
SWBatt (1 ) 'Power CS625 sensors up
PeriodAvg(Period_uS(1),1,0,100,10,1,1,0)
PeriodAvg(Period_uS(2),2,0,100,10,1,1,0)
PeriodAvg(Period_uS(3),3,0,100,10,2,1,0)
PeriodAvg(Period_uS(4),4,0,100,10,2,1,0)
SWBatt (0) 'Power CS625 sensors down
For LoopCnt = 1 To 4 'convert raw values to volumetric water content
TxData(LoopCnt)=-0.0663-0.0063*Period_uS(LoopCnt)+0.0007*Period_uS(
Next LoopCnt
EndIf

Time = TimeUntilTransmit(1) 'copy countdown time to public variable

If Time = 0 Then 'when countdown reaches zero power radio and transmit
SendGetData (Response,Rx,TxData(),1,2,2,00000)
EndIf
CallTable(VWC_Pin)
NextScan
EndProg

111
Section 11. Programming Resource Library

11.3 Multiple Switch Closure Measurements

Pulse channel P_SW detects switch closures but P_LL does not. In order to
detect more than one switch closure device, a 100kOhm pull-up resistor must be
connected between Battery+ and P_LL, C1, or C2. With the pull-up resistor in
place P_LL or the control port can detect a switch closure. In the following
example p. 112, note that the PulseCount instruction for P_SW uses
configuration option 2 (Switch Closure), while P_LL must use option 0 (Pulse
Input).

CRBASIC EXAMPLE 18. CRBASIC EXAMPLE. Two Rain Gages on a CR200(X)

'Rain(1) is wired to P_SW and Ground
'Rain(2) is wired to P_LL and Ground with a
'100,000 ohm resistor connecting P_LL to Battery+

Public Rain(2)

Units Rain()=mm

DataTable(Hourly,True,-1)
DataInterval(0,60,Min)
Totalize(2,Rain(),False)
EndTable

BeginProg
Scan(10,Sec)
PulseCount(Rain(1),P_SW,2,0,0.254,0)
PulseCount(Rain(2),P_LL,0,0,0.254,0)
CallTable(Hourly)
NextScan
EndProg

11.4 SDI-12 Sensor Support

11.4.1 SDI-12 Command Basics
Commands have three components:
Sensor address (a) – a single character, and is the first character of the
command. Sensors are usually assigned a default address of zero by the
manufacturer. Wildcard address (?) is used in Address Query command.
Some manufacturers may allow it to be used in other commands.

Command body (e.g., M1) – an upper case letter (the “command”) followed
by alphanumeric qualifiers.

Command termination (!) – an exclamation mark.

An active sensor responds to each command. Responses have several standard

forms and terminate with <CR><LF> (carriage return – line feed).

112
 Section 11. Programming Resource Library

SDI-12 commands and responses are defined by the SDI-12 Support Group
(www.sdi-12.org) and are summarized in TABLE. Standard SDI-12 Command
& Response Set (p. 113). Sensor manufacturers determine which commands to
support. The most common commands are detailed below.

Table 14. Standard SDI-12 Command & Response Set

Name Command1 Response2
Break Continuous None
spacing for at least
12 milliseconds
Acknowledge Active a! a<CR><LF>
Send Identification aI! allccccccccmmmmmmvvvxxx...xx<CR><LF>
Change Address aAb! b<CR><LF> (support for this command is required only
if the sensor supports software changeable addresses)
Address Query ?! a<CR><LF>
3
Start Measurement aM! atttn<CR><LF>

Start Measurement and Request aMC! atttn<CR><LF>

3
CRC
Send Data aD0! a<values><CR><LF> or a<values><CRC><CR><LF>
. a<values><CR><LF> or a<values><CRC><CR><LF>
. a<values><CR><LF> or a<values><CRC><CR><LF>
. a<values><CR><LF> or a<values><CRC><CR><LF>
aD9! a<values><CR><LF> or a<values><CRC><CR><LF>
3
Additional Measurements aM1! atttn<CR><LF>
. atttn<CR><LF>
. atttn<CR><LF>
. atttn<CR><LF>
aM9! atttn<CR><LF>
Additional Measurements and aMC1! ... aMC9! atttn<CR><LF>
3
Request CRC
3
Start Verification aV! atttn<CR><LF>

Start Concurrent Measurement aC! atttnn<CR><LF>

Additional Concurrent
Measurements aC1! atttnn<CR><LF>
. atttnn<CR><LF>
. atttnn<CR><LF>
. atttnn<CR><LF>
aC9! atttnn<CR><LF>
Additional Concurrent
Measurements and Request CRC aCC1! ... aCC9! atttnn<CR><LF>
Continuous Measurements aR0! ... aR9! a<values><CR><LF> (formatted like the D commands)
Continuous Measurements and aRC0! ... aRC9! a<values><CRC><CR><LF> (formatted like the D
Request CRC commands)
1
If the terminator '!' is not present, the command will not be issued. The CRBASIC SDI12Recorder () instruction, however, will
still pick up data resulting from a previously issued "C!" command.
2
Complete response string can be obtained when using the SDIRecorder () instruction by declaring the Destination variable as
String.
3
This command may result in a service request.

113
Section 11. Programming Resource Library

11.4.1.1 Addressing
A single probe should be connected to an SDI-12 input when using these
commands.

11.4.1.1.1 Address Query Command (?!)

Command ?! requests the address of the connected sensor. The sensor replies to
the query with the address, a.

11.4.1.1.2 Change Address Command (aAb!)

Sensor address is changed with command aAb!, where a is the current address
and b is the new address. For example, to change an address from 0 to 2, the
command is 0A2! The sensor responds with the new address b, or in this
example 2.

11.4.1.1.3 Send Identification Command (aI!)

Sensor identifiers are requested by issuing command aI!. The reply is defined
by the sensor manufacturer, but usually includes the sensor address, SDI-12
version, manufacturer's name, and sensor model information. Serial number or
other sensor specific information may also be included.

An example of a response from the aI! command is:

013NRSYSINC1000001.2101 <CR><LF>

where:

• Address = 0

• SDI-12 version =1.3

• Manufacturer = NRSYSINC

• Sensor model = 100000

• Sensor version = 1.2

• Serial number = 101

11.4.1.2 Start Measurement Commands (aM! & aC!)

A measurement is initiated with M! or C! commands. The response to each
command has the form atttnn, where

• a = sensor address

• ttt = time, in seconds, until measurement data are available

• nn = the number of values to be returned when one or more subsequent D!

commands are issued.

114
 Section 11. Programming Resource Library

11.4.1.2.1 Start Measurement Command (aMv!)

Qualifier v is a variable between 1 and 9. If supported by the sensor

manufacturer, v requests variant data. Variants may include:

• alternate units (e.g. °C or °F)

• additional values (e.g., level and temperature)

• diagnostic of the sensor’s internal battery

Example:
Command: 5M!

Response: 500410 (atttnn, indicates address 5, data ready in 4 seconds, will

report 10 values).

Example:
Command: 5M7!

Response: 500201 (atttnn indicates address 5, data ready in 2 seconds, will

report 1 value). v = 7 instructs the sensor to return the voltage of its internal
battery.

11.4.1.2.2 Start Concurrent Measurement Command (aC!)

Concurrent measurement allows the CR200(X) to request a measurement,

continue program execution, and pick up the requested data on the next pass
through the program. The datalogger scan rate should be set such that the
resulting skew between time of measurement and time of data collection does
not compromise data integrity.

Note This command is new to Version 1.2 or higher of the SDI-12

Specification. Older sensors, older loggers, or new sensors that do not meet
v1.2 specifications will likely not support this command

11.4.1.2.3 Aborting a Measurement Command

A measurement command (M! or C!) is aborted when any other valid command
is sent to the sensor.

11.4.1.3 Send Data Commands (aDv! & aRv!)

11.4.1.3.1 Send Data Command (aDv!)

This command requests data from the sensor. It is normally issued

automatically by the datalogger after measurement commands aMv! or aCv!. In
transparent mode, the user asserts this command to obtain data. If the expected
number of data values are not returned in response to a aD0! command, the data

115
Section 11. Programming Resource Library

logger issues aD1!, aD2!, etc., until all data are received. The limiting
constraint is that the total number of characters that can be returned to a aDv!
command is 35 characters (75 characters for aCv!). If the number of characters
exceed the limit, the remainder of the response are obtained with subsequent
aDv! commands wherein v increments with each iteration.

11.4.1.3.2 Continuous Measurements Command (aRv!)

Sensors designed to continuously monitor the measured phenomena, such as a

shaft encoder, do not require a measurement command (e.g., aMv!). They are
read directly with the aRv! command. If a sensor cannot perform continuous
measurements, then it responds to aRv! with the sensor address.

11.4.2 SDI-12 Communications

The CR200(X) supports SDI-12 communication through two modes –
transparent mode and programmed mode.

• Transparent mode facilitates sensor set-up and troubleshooting. It allows

commands to be manually issued and the full sensor response viewed.
Transparent mode does not log data.

• Programmed mode automates much of the SDI-12 protocol and provides

for data recording.

Multiple SDI-12 sensors can be connected to an SDI-12 input: . If multiple

sensors are wired to a single channel, each sensor must have a unique address.
SDI-12 standard v 1.3 sensors accept addresses 0 - 9, a - z, and A - Z.

If program mode communications is not successful, NAN will be loaded into the
first variable specified in SDI12Recorder () instruction. See Section NAN and
±INF (p. 153) for more information.

11.4.2.1 SDI-12 Transparent Mode

System operators can manually interrogate and enter settings in probes using
transparent mode. Transparent mode is useful in troubleshooting SDI-12
systems because it allows direct communication with probes.

Transparent mode may need to wait for commands issued by the programmed
mode to finish before sending responses. While in transparent mode, datalogger
programs may not execute. Datalogger security may need to be unlocked before
transparent mode can be activated.

Transparent mode is entered while the PC is in telecommunications with the

datalogger through a terminal emulator program. It is easily accessed through
Campbell Scientific datalogger support software, but may also be accessible
with terminal emulator programs such as Windows Hyperterminal. Keyboard
displays cannot be used.

To enter the SDI-12 transparent mode, enter the support software terminal
emulator. Click the “Open Terminal” button. A green “Active” indicator

116
 Section 11. Programming Resource Library

appears on the screen as shown in FIGURE. Entering SDI-12 Transparent Mode

(p. 117). Press <Enter> until the CR200(X) responds with the prompt
“CR200(X)>”. Type “SDI12” at the prompt (without the quotes) and press
<Enter>. An “Entering SDI12 Terminal” response indicates that SDI-12
Transparent Mode is active and ready to transmit SDI-12 commands and display
responses.

Figure 44: Entering SDI-12 Transparent Mode

11.4.2.2 SDI-12 Programmed Mode

Routine SDI-12 measurements require that issuance of commands and
interpretation of sensor responses be automated. Commands entered into the
SDIRecorder () instruction differ slightly in function from commands entered in
transparent mode. In transparent mode, for example, the operator manually
enters aM! and aD0! to initiate a measurement and get data, with the operator
providing the proper time delay between the request for the measurement and
the request for the data. In programmed mode, the CR200(X) provides
command and timing services within a single line of code. For example, when
the SDI12Recorder() instruction is programmed with the M! command (note
that SDI-12 address is a separate parameter), the CR200(X) issues the aM! AND
aD0! commands with proper elapsed time between the two. The CR200(X)
automatically issues retries as well as other services designed to make the SDI-
12 measurement work as trouble free as possible. TABLE. SDI-12Recorder ()
Commands p. 118 summarizes CR200(X) actions triggered by some
SDI12Recorder commands.

117
Section 11. Programming Resource Library

SDIRecorder () Instruction
SDICommand Entry Actions Internal to CR200(X) and
Sensor

Mv! CR200(X): Issues aMv! command

Sensor: Responds with atttnn
CR200(X): Waits until ttt1 seconds.
Issues aDv! command(s)

Sensor: Responds with data.

Cv! CR200(X): Issues aCv! command

Sensor: Responds with atttnn
CR200(X): If ttt=0 then issues aDv!
command(s)

Sensor: Responds with data.

CR200(X): else, if ttt>0 then moves to
next CRBASIC program instruction.

CR200(X): At next time SDIRecorder()

is executed, if elapsed time < ttt, moves
to next CRBASIC instruction,.

CR200(X): else, issues aDv!

command(s)

Sensor: Responds with data.

CR200(X): Issues aCv! command (to
request data for next scan).

Cv (note: no ! termination) CR200(X): Tests to see if ttt expired.

If ttt not expired, loads "1e9" into first
variable then moves to next CRBASIC
instruction. If ttt expired, issues aDv!
command(s).

Sensor: Responds to aDv! command(s)

with data, if any. If no data, loads NAN
into variable.

CR200(X): moves to next CRBASIC

instruction (does not re-issue aCv!
command).
1
Note that ttt is local only to the SDIRecorder() instruction.

11.4.3 SDI-12 Power Considerations

When a command is sent by the datalogger to an SDI-12 probe, all probes on
the same SDI-12 port will wake up. Only the probe addressed by the datalogger

118
 Section 11. Programming Resource Library

will respond, however, all other probes will remain active until the timeout
period expires.

Example:

Probe: Water Content

Power Usage:

• Quiescent: 0.25 mA

• Measurement: 120 mA

• Measurement Time: 15 s

• Active: 66 mA

• Timeout: 15 s

Probes 1, 2, 3, and 4 are connected to SDI-12 / Control Port 1.

The time line in TABLE. Example Power Usage Profile for a Network of SDI-12
Probes (p. 119) shows a 35 second power usage profile example.

Table 15. Example Power Usage Profile for a Network of SDI-12 Probes

All Time
Probes Out Total
Sec Command Awake Expires 1 mA 2 mA 3mA 4mA mA
1 1M! Yes 120 66 66 66 318
2 120 66 66 66 318
• • • • • •
• • • • • •
• • • • • •
14 120 66 66 66 318
15 Yes 120 66 66 66 318
16 1D0! Yes 66 66 66 66 264
17 66 66 66 66 264
• • • • • •
• • • • • •
• • • • • •
29 66 66 66 66 264
30 Yes 66 66 66 66 264
31 0.25 0.25 0.25 0.25 1
• • • • • •
• • • • • •
• • • • • •
35 0.25 0.25 0.25 0.25 1

119
Section 11. Programming Resource Library

For most applications, total power usage of 318 mA for 15 seconds is not
excessive, but if 16 probes were wired to the same SDI-12 port, the resulting
power draw would be excessive. Spreading sensors over several SDI-12
terminals will help reduce power consumption.

11.5 Wind Vector

11.5.1 OutputOpt Parameters
In the CR200(X) WindVector () instruction, the OutputOpt parameter is used to
define the values which are stored. All output options result in an array of
values, the elements of which have "_WVc(n)" as a suffix, where n is the
element number. The array uses the name of the Speed/East variable as its base.
TABLE. OutputOpt Options (p. 120) lists and describes OutputOpt options.

Table 16. OutputOpt Options

Option Description (WVc() is the Output Array)
WVc(1): Mean horizontal wind speed (S)
0
WVc(2): Unit vector mean wind direction (Θ1)
WVc(3): Standard deviation of wind direction σ(Θ1). Standard deviation is calculated using the Yamartino
algorithm. This option complies with EPA guidelines for use with straight-line Gaussian dispersion models
to model plume transport.
1 WVc(1): Mean horizontal wind speed (S)
WVc(2): Unit vector mean wind direction (Θ1)
2 WVc(1):Resultant Mean horizontal wind speed (Ū)
WVc(2): Resultant mean wind direction (Θu)
WVc(3): Standard deviation of wind direction σ(Θu). This standard deviation is calculated using Campbell
Scientific's wind speed weighted algorithm. Use of the resultant mean horizontal wind direction is not
recommended for straight-line Gaussian dispersion models, but may be used to model transport direction in
a variable-trajectory model.

11.5.2 Wind Vector Processing

WindVector () processes wind speed and direction measurements to calculate
mean speed, mean vector magnitude, and mean vector direction over a data
storage interval. Measurements from polar (wind speed and direction) or
orthogonal (fixed East and North propellers) sensors are accommodated. Vector
direction and standard deviation of vector direction can be calculated weighted
or unweighted for wind speed.

When a wind speed measurement is zero, WindVector () uses the measurement

to process scalar or resultant vector wind speed and standard deviation, but not
the computation of wind direction.

120
 Section 11. Programming Resource Library

Note Cup anemometers typically have a mechanical offset which is added to

each measurement. A numeric offset is usually encoded in the CRBASIC
program to compensate for the mechanical offset. When this is done, a
measurement will equal the offset only when wind speed is zero; consequently,
additional code is often included to zero the measurement when it equals the
offset so that WindVector () can reject measurements when wind speed is zero.

11.5.2.1 Measured Raw Data

• Si: horizontal wind speed

• Θi: horizontal wind direction

• Uei: east-west component of wind

• Uni: north-south component of wind

• N: number of samples

11.5.2.2 Calculations

11.5.2.2.1 Input Sample Vectors

Figure 45: Input Sample Vectors

In FIGURE. Input Sample Vectors (p. 121) the short, head-to-tail vectors are the
input sample vectors described by si and Θi, the sample speed and direction, or
by Uei and Uni, the east and north components of the sample vector. At the end
of data storage interval T, the sum of the sample vectors is described by a vector
of magnitude U and direction Θu. If the input sample interval is t, the number of
samples in data storage interval T is N = T / t. The mean vector magnitude is Ū
= U / N.

121
Section 11. Programming Resource Library

Scalar mean horizontal wind speed, S:

where in the case of orthogonal sensors:

Unit vector mean wind direction,

where

or, in the case of orthogonal sensors

where

Standard deviation of wind direction (Yamartino algorithm)

where,

and Ux and Uy are as defined above.

122
 Section 11. Programming Resource Library

11.5.2.2.2 Mean Wind Vector

Resultant mean horizontal wind speed, Ū:

Figure 46: Mean Wind Vector

where for polar sensors:

or, in the case of orthogonal sensors:

Resultant mean wind direction, Θu:

Standard deviation of wind direction, σ (Θu), using Campbell Scientific

algorithm:

The algorithm for σ (Θu) is developed by noting (FIGURE. Standard Deviation

of Direction (p. 124)) that

123
Section 11. Programming Resource Library

where

Figure 47: Standard Deviation of Direction

The Taylor Series for the Cosine function, truncated after 2 terms is:

For deviations less than 40 degrees, the error in this approximation is less than
1%. At deviations of 60 degrees, the error is 10%.

The speed sample can be expressed as the deviation about the mean speed,

Equating the two expressions for Cos (θ') and using the previous equation for si;

Solving for (Θi')2, one obtains;

Summing (Θi')2 over N samples and dividing by N yields the variance of Θu.
Note that the sum of the last term equals 0.

The term,

is 0 if the deviations in speed are not correlated with the deviation in direction.
This assumption has been verified in tests on wind data by CSI; the Air

124
 Section 11. Programming Resource Library

Resources Laboratory, NOAA, Idaho Falls, ID; and MERDI, Butte, MT. In
these tests, the maximum differences in

and

have never been greater than a few degrees.

The final form is arrived at by converting from radians to degrees (57.296

degrees/radian).

11.6 TrigVar and DisableVar - Controlling Data

Output and Output Processing
TrigVar is the third parameter in the DataTable () instruction. It controls
whether or not a data record is written to final storage. TrigVar control is subject
to other conditional instructions such as the DataInterval () instruction.

DisableVar is the last parameter in most output processing instructions, such as

Average (), Maximum (), Minimum (), etc. It controls whether or not a
particular measurement or value is included in the affected output processing
function.

Note Together, TrigVar and DataInterval () grant functionality similar to Flag 0

in earlier generation CSI mixed-array dataloggers, such as the CR10X.
DisableVar grants functionality similar to Flag 9.

For individual measurements to affect summary data, output processing

instructions such as Average () must be executed whenever the DataTable is
called from the program - normally once each Scan. For example, for an average
to be calculated for the hour, each measurement must be added to a total over
the hour. This accumulation of data are not affected by TrigVar. TrigVar only
controls the moment when the final calculation is performed and the processed
data (the average) is written to the data table. For this summary moment to
occur, TrigVar and all other conditions (i.e. DataInterval) must be true. To
restate, when TrigVar is false, output processing instructions (e.g. Average ())
perform intermediate processing but not their final processing, and a new record
will not be created.

Note In many applications, output records are solely interval based and TrigVar
is set to TRUE (-1) always. In these applications DataInterval () is the sole
specifier of the output trigger condition.

125
Section 11. Programming Resource Library

CRBASIC EXAMPLE. Using TrigVar to Trigger Data Storage (p. 126) lists
CRBASIC code that uses TrigVar () rather than DataInterval () to trigger data
storage. FIGURE. Data from TrigVar Program (p. 126) shows data produced by
the example code.

CRBASIC EXAMPLE 19. Using TrigVar to Trigger Data Storage

In this example, the variable "counter" is incremented by 1 each scan. The data table is c
includes the Sample (), Average (), and Totalize () instructions. TrigVar is true when
Data are stored when TrigVar is true. Data stored are the sample, average, and total o
which is equal to 0, 1, 2, 3, or 4 when the data table is called.
Public counter

DataTable (Test,counter=2 or counter=3,100)

Sample (1,counter,FP2)
Average (1,counter,FP2,False)
Totalize (1,counter,FP2,False)
EndTable
BeginProg
Scan (1,Sec,0,0)
counter = counter+1
If counter = 5 Then
counter = 0
EndIf
CallTable Test
NextScan
EndProg

Figure 48: Data from TrigVar Program

11.7 Multiple Data Intervals in Data Tables

The trigger variable may be used to set conditions where data is written to a data
table on more than one time interval. CRBASIC EXAMPLE. Programming for
Two Data Intervals in One Data Table p. 127 shows how this is done. Rather
than using the DataInterval instruction, output times are specified by inserting If

126
 Section 11. Programming Resource Library

Time instructions in the TrigVar parameter of the DataTable declaration. Since

DataInterval is not used, the table size cannot be autoallocated and table size
should be carefully considered before being set to a specific number of records.

CRBASIC EXAMPLE 20. CRBASIC EXAMPLE. Programming for two data intervals in
one data table
'CRBASIC program to write to a single table with two different time
'intervals.

'Declare Public Variables

Public T109_C(2), Counter, deltaT
Public int_fast, int_slow
'Data Tables
'Table output on two intervals depending on condition.
'note the parenthesis around the TriggerVariable AND statements

DataTable (TwoInt,(int_fast AND IfTime(0,5,Sec)) OR (int_slow AND IfTime (0,15,sec)),1000)

Sample (2,T109_C())
Maximum (1,counter(1),False,False)
Minimum (1,counter(1),False,False)
Maximum (1,deltaT,False,False)
Minimum (1,deltaT,False,False)
Average (1,deltaT,false)
EndTable

'Main Program
BeginProg
Scan (1,Sec)
counter(1) = counter(1) + 1
'Thermistor measurement
Therm109 (T109_C(),2,1,Ex1,1.0,0)
'calculate the difference in thermistor temperatures
deltaT = T109_C(1)-T109_C(2)

'when the difference in temperatures is >=3 turn LED on

'and trigger the data table's faster interval
If deltaT >= 3 Then
PortSet (1,1)
int_fast = -1
int_slow = 0

Else
PortSet (C1,0)
int_fast = 0
int_slow = -1
EndIf

'Call Output Tables

CallTable TwoInt
NextScan
EndProg

127
Section 11. Programming Resource Library

128
Section 12. Memory and Data Storage
12.1 Data Storage
The CR200(X) can be programmed to store each measurement or, more
commonly, to store processed values such as averages, maxima, minima, etc.
Data are stored periodically or conditionally in data tables as directed by the
CRBASIC program (CRBASIC EXAMPLE. Proper Program Structure p. 73).
The DataTable () instruction allows the user to set the size of the data table. The
maximum number of tables that can be created by the program is 4 for CR200
series dataloggers and 8 for CR200(X) series dataloggers.

12.1.1 Data Table Storage

Data tables are stored in Serial Flash EEPROM. Data remain in memory when
the CR200(X) is powered down. Data are erased when a different program is
loaded and run. The Serial Flash EEPROM is good for more than 100,000 write
cycles.

Caution! If an EEPROM memory failure is detected, the datalogger

suspends running the program and red LED flashes twice every scan
interval. “Trap Code” in the Status Table will be set to 16. The
datalogger must be returned to CSI to replace the Serial Flash
EEPROM.

The CR200(X) stores the final storage data in the Serial Flash EEPROM. The
Serial Flash EEPROM also is the storage area for a file called the Table
Definition File (TDF). When a CRBASIC program is downloaded to the
CR200(X), the TDF is extracted from the compiled version of the CRBASIC
program and stored in the Serial Flash EEPROM. Any remaining memory can
be used for the final storage allocation. In the CR200, there are 128k bytes or
512k bytes of Serial Flash EEPROM (dataloggers with a 512 kbyte EEPROM
will have 512K on their label). Up to 5.12k bytes of that memory can be used
for the TDF (if the TDF is greater than the maximum, the compile will fail). If
the data table allocation or size of all or any of the tables use too much memory,
there will NOT be a compile error. The CR200(X) will force the allocation to
work by adding all the sizes for each table, checking if the sum is greater than
the Serial Flash EEPROM and dropping the allocation for each table by 90
percent. This is repeated until the sums of the allocations are below the Serial
Flash EEPROM size.

129
Section 12. Memory and Data Storage

12.2 Memory Conservation

One or more of the following memory saving techniques can be used on the rare
occasions when a program reaches memory limits:

• Declare variables as DIM instead of Public. DIM variables do not require

buffer memory for data retrieval.

• Reduce arrays to the minimum size needed. Each variable, whether or not
part of an array, requires about the same amount of memory.
Approximately 70 variables will fill available memory.

• Use variable arrays with aliases instead of individual variables with unique
names. Aliases consume less memory than unique variable names.

12.3 Memory Reset

Three features are available for complete or selective reset of CR200(X)
memory.

12.3.1 Full Memory Reset

Full memory reset occurs when an operating system is sent to the CR200(X)
using DevConfig. A full memory reset does the following:

• Clears and Formats CPU: drive (all program files erased)

• Clears SRAM data tables

• Clears Status Table Elements

• Restores settings to default

• Initializes system variables

• Clears communications memory

12.3.2 Program Send Reset

All SRAM and CRD: data are erased when user programs are uploaded. This
will occur even when a program with identical data tables is sent to the
CR200(X).

12.3.3 Manual Data Table Reset

Data table memory is reset using the ResetTables field of the Status table.
Change the value from 0 to 8888 to reset all data tables.

130
Section 13. Telecommunications and
Data Retrieval
Telecommunications, in the context of CR200(X) operation, is the movement of
information between the CR200(X) and another computing device, usually a
PC. The information can be programs, data, files, or control commands.

Telecommunications systems require three principal components: hardware,

carrier signal, and protocol. For example, a common way to communicate with
the CR200(X) is with PC200W software by way of a PC COM port. In this
example, hardware are the PC COM port, the CR200(X) RS-232 port, and a
serial cable. The carrier signal is RS-232, and the protocol is PakBus®. Of these
three, a user most often must come to terms with only the hardware, since the
carrier signal and protocol are transparent in most applications.

Systems usually require a single type of hardware and carrier signal. Some
applications, however, require hybrid systems, which utilize two or more
hardware and signal carriers.

Contact a Campbell Scientific applications engineer for assistance in

configuring any telecommunications system.

Synopses of software to support the various telecommunications devices and

protocols are found in Section Support Software (p. 143).

13.1 Hardware and Carrier Signal

Campbell Scientific supplies or recommends a wide range of
telecommunications hardware. TABLE. CR200(X) Telecommunications Options
(p. 131) lists telecommunications destination, device, path, and carrier options
which imply certain types of hardware for use with the CR200(X) datalogger.
Information in TABLE. CR200(X) Telecommunications Options (p. 131) is
conceptual. For specific model numbers and specifications, see APPENDIX.
Telecommunications Hardware (Appendix p. 32), contact a Campbell Scientific
applications engineer, or go to www.campbellsci.com.

Table 17. CR200(X) Telecommunications Options

Destination
Device / Portal Communications Path Carrier Signal
PC / COM or USB Direct Connect RS-232
PDA / COM Port Direct Connect RS-232
PC / COM Port Digital Cellular 800 MHz RF
PC / COM Port Multidrop RS485
PC / Network Card Ethernet / PPP IP
PC / COM Port Spread Spectrum RF 900 MHz RF
Satellite System Satellite Transceiver RF
Digital Display Direct Connect RS-232

131
Section 13. Telecommunications and Data Retrieval

NOTE: The CR200(X) operates at a baud rate of 9600 baud. Attempting to

connect at a higher baud rate will result in communications errors.

13.2 Protocols
The primary telecommunication protocol for the CR200(X) is PakBus (PakBus
Overview (p. 133)). ModBus is also supported on board (Alternate Telecoms
Resource Library (p. 139)).

13.3 Initiating Telecommunications

Telecommunications sessions are initiated by a PC running Campbell Scientific
datalogger support software (Support Software p. 143). Once
telecommunication is established, the PC issues commands to send programs,
set clocks, collect data, etc. Because data retrieval is managed by the PC, several
PCs can have access to a CR200(X) without disrupting the continuity of data.

13.4 Data Retrieval

Data tables are transferred to PC files through a telecommunications link
(Telecommunications and Data Retrieval (p. 131)).

13.4.1 Via Telecommunications

Data are usually transferred through a telecommunications link to an ASCII file
on the supporting PC using Campbell Scientific datalogger support software
(Support Software (p. 143)). See also the manual and Help for the software
package being used.

13.4.2 Data Format on Computer

CR200(X) data stored on a PC via support software is formatted as either ASCII
or Binary depending on the file type selected in the support software. Consult
the software manual for details on the various available data file formats.

132
Section 14. PakBus Overview
Read More! This section is provided as a primer to PakBus® communications.
Complete information is available in Campbell Scientific's "PakBus Networking
Guide", available at www.campbellsci.com.

The CR200(X) communicates with computers or other Campbell Scientific

dataloggers via PakBus®. PakBus® is a proprietary telecommunications protocol
similar in concept to IP (Internet protocol). PakBus® allows compatible
Campbell Scientific dataloggers and telecommunications peripherals to
seamlessly link to a PakBus® network.

14.1 PakBus Addresses

CR200(X)s are assigned PakBus® address 1 as a factory default. Networks with
more than a few stations should be organized with an addressing scheme that
guarantees unique addresses for all nodes. One approach, demonstrated in
FIGURE. PakBus Network Addressing (p. 134), is to assign single-digit
addresses to the first tier of nodes, multiples of tens to the second tier, multiples
of 100s to the third, etc. Note that each node on a branch starts with the same
digit. Devices, such as PCs, with addresses greater than 4000 are given special
administrative access to the network

PakBus addresses are set using DevConfig, PakBusGraph, or the CR200(X)

status table. DevConfig (Device Configuration Utility) is the primary settings
editor for Campbell Scientific equipment. It requires a hardwire RS-232
connection to a PC and allows backup of settings on the PC hard drive.
PakBusGraph is used over a telecommunications link to change settings, but has
no provision for backup.

Caution Care should be taken when changing PakBus® addresses with

PakBusGraph or in the status table. If an address is changed to an unknown
value, a field visit with a laptop and DevConfig may be required to discover the
unknown address.

14.2 Nodes: Leaf Nodes and Routers

• A PakBus® network consists of 2 to 4093 linked nodes.

• One or more leaf nodes and routers can exist in a network.

• Leaf nodes are measurement devices at the end of a branch of the PakBus®
web.

• Leaf nodes can be linked to any router.

• A leaf node cannot route packets but can originate or receive them.

133
Section 14. PakBus Overview

• Routers are measurement or telecommunications devices that route packets

to other linked routers or leaf nodes.

• Routers can be branch routers. Branch routers only know as neighbors

central routers, routers in route to central routers, and routers one level
outward in the network.

• Routers can be central routers. Central routers know the entire network. A
PC running LoggerNet is typically a central router.

• Routers can be router-capable dataloggers or communications devices.

The CR200(X) is always a leaf node. It cannot be configured as a router. The

network shown in FIGURE. PakBus Network Addressing (p. 134) contains 6
routers and 8 leaf nodes.

Figure 49: PakBus Network Addressing.

LoggerNet is configured by default as a router and can route datalogger to

datalogger communications.

14.3 Router and Leaf Node Configuration

Consult APPENDIX. Router and Leaf Node Hardware (Appendix p. 33) for a
table of available PakBus® leaf node and router devices.

14.4 Linking Nodes: Neighbor Discovery

To form a network, nodes must establish links with neighbors (adjacent nodes).
Links are established through a process called discovery. Discovery occurs when
nodes exchange hellos. A hello exchange occurs during a hello-message
between two nodes.

134
 Section 14. PakBus Overview

14.4.1 Hello-message (two-way exchange)

A hello-message is an interchange between two nodes that negotiates a neighbor
link. A hello-message is sent out in response to one or both of either a beacon or
a hello-request.

14.4.2 Beacon (one-way broadcast)

A beacon is a broadcast sent by a node at a specified interval telling all nodes
within hearing that a hello-message can be sent. If a node wishes to establish
itself as a neighbor to the beaconing node, it will then send a hello-message to
the beaconing node. Nodes already established as neighbors will not respond to
a beacon.

14.4.3 Hello-request (one-way broadcast)

All nodes hearing a hello-request broadcast (existing and potential neighbors)
will issue a hello-message to negotiate or re-negotiate a neighbor relationship
with the broadcasting node.

14.4.4 Neighbor Lists

PakBus® devices in a network can be configured with a neighbor list. The
router or master sends out a hello-message to each node in the list whose verify
interval has expired at a random interval*. If a node responds, a hello-message
is exchanged and the node becomes a neighbor.

*A random number of seconds between INTERVAL and (2 * INTERVAL),

where INTERVAL is the Verify Interval setting if non-zero, or 30 seconds if the
Verify Interval setting is zero.

Neighbor filters dictate which nodes are neighbors and force packets to take
routes specified by the network administrator. LoggerNet (a PakBus® node)
derives its neighbor filter from link information in the Setup device map.

14.4.5 Adjusting Links

PakBusGraph, a client of LoggerNet, is particularly useful when testing and
adjusting PakBus® routes.

Paths established by way of beaconing may be redundant and vary in reliability.

Redundant paths can provide backup links in the event the primary path fails.
Redundant and unreliable paths can be eliminated by activating neighbor filters
in the various nodes and by disabling some beacons.

135
Section 14. PakBus Overview

14.4.6 Maintaining Links

Links are maintained by means of the CVI (communications verification
interval). The CVI can be specified in each node with DevConfig. The following
rules 1 apply:

• If Verify Interval = 0, then CVI = 2.5 x beacon interval*

• If Verify Interval = 60, then CVI = 60 seconds*

• If Beacon Interval = 0 and Verify Interval = 0, then CVI = 300 seconds*

• If a router or master does not hear from a neighbor for one CVI, it begins
again to send a Hello message to that node at the random interval.

Users should base verification intervals on the timing of normal

communications such as scheduled LoggerNet collections or datalogger to
dataloggers communications. The idea is to not allow the verification interval to
expire before normal communications. If the verification interval expires the
devices will initiate hello exchanges in an attempt to regain neighbor status,
increasing traffic in the network.

Note: During the hello-message, a CVI must be negotiated between two

neighbors. The negotiated CVI is the lesser of the first nodes CVI and 6/5ths of
the neighbors CVI.

14.5 Troubleshooting
Various tools and methods have been developed to assist in troubleshooting
PakBus® networks.

14.5.1 Link Integrity

With beaconing or neighbor filter discovery, links are established and verified
using relatively small data packets (Hello messages). When links are used for
regular telecommunications, however, longer messages are used. Consequently,
a link may be reliable enough for discovery but unreliable with larger packets.
This condition is most common in radio networks, particularly when max packet
size is >200.

PakBus® communications over marginal links can often be improved by

reducing the size of the PakBus® packets. Best results are obtained when the
maximum packet sizes in both nodes are reduced.

1
During the hello-message, a CVI must be negotiated between two neighbors.
The negotiated CVI is the lesser of the first nodes CVI and 6/5ths of the
neighbors CVI.

136
 Section 14. PakBus Overview

14.5.1.1 Automatic Packet Size Adjustment

The BMP5 file receive transaction allows the BMP5 client (LoggerNet) to
specify the size of the next fragment of the file that the CR200(X) sends.

Note The file receive transaction is used to get table definitions from the
datalogger.

Because LoggerNet must specify a size for the next fragment of the file, it uses
whatever size restrictions that apply to the link.

Hence, the size of the responses to the file receive commands that the CR200(X)
sends is governed by the maxPacketSize setting for the datalogger as well as
that of any of its parents in LoggerNet's network map. Note that this calculation
also takes into account the error rate for devices in the link.

BMP5 data collection transaction does not provide any way for the client to
specify a cap on the size of the response message. This is the main reason why
the "Max Packet Size" setting exists in the CR200(X). The CR200(X) can look
at this setting at the point where it is forming a response message and cut short
the amount of data that it would normally send if the setting limits the message
size.

14.5.2 Ping
Link integrity can be verified with the following procedure by using
PakBusGraph | Ping Node. Nodes can be pinged with packets of 50, 100, 200 or
500 bytes.

Note Do not use packet sizes greater than 90 when pinging with 100 mW radio
modems and radio enabled dataloggers (APPENDIX. Telecommunications
Hardware (Appendix p. 32)).

Pinging with ten repetitions of each packet size will characterize the link. Before
pinging, all other network traffic (scheduled data collections, clock checks, etc.)
should be temporarily disabled. Begin by pinging the first layer of links
(neighbors) from the PC, then proceed to nodes that are more than one hop
away. TABLE. PakBus Link Performance Gage (p. 137) provides a link
performance gage.

Table 18. PakBus Link Performance Gage

500 byte
Ping Sent Successes Link Status
10 10 excellent
10 9 good
10 7-8 adequate
10 <7 marginal

137
Section 14. PakBus Overview

14.5.3 Traffic Flow

Keep beacon intervals as long as possible with higher traffic (large numbers of
nodes and / or frequent data collection). Long beacon intervals minimize
collisions with other packets and resulting retries. The minimum recommended
beacon interval is 60 seconds. If communications traffic is high, consider setting
beacon intervals of several minutes. If data throughput needs are great,
maximize data bandwidth by creating some branch routers, and / or by
eliminating beacons altogether and setting up neighbor filters.

14.6 LoggerNet Device Map Configuration

As shown in FIGURE. Flat Map (p. 138) and FIGURE. Tree Map (p. 138), the
essential element of a PakBus® network device map in LoggerNet is the
PakBusPort. After adding the root port (COM, IP, etc), add a PakBusPort and
the dataloggers.

Figure 50: Flat Map

Figure 51: Tree Map

Use the 'tree' configuration when communications requires routers. The shape of
the map serves to disallow a direct LoggerNet connection to CR1000_2 and
CR200Series, and implies constrained routes that will probably be established
by user-installed neighbor filters in the routers. This assumes that LoggerNet
beacons are turned off. Otherwise, with a default address of 4094, LoggerNet
beacons will penetrate the neighbor filter of any in-range node.

138
Section 15. Alternate Telecoms
Resource Library
15.1 Modbus
15.1.1 Overview
Modbus is a widely used SCADA communication protocol that facilitates
exchange of information and data between computers / HMI software,
instruments (RTUs) and Modbus compatible sensors. The CR200(X)
communicates via Modbus over RF and RS-232.

Modbus systems consist of a master (PC), RTU / PLC slaves, field instruments
(sensors), and the communications network hardware. The communications
port, baud rate, data bits, stop bits, and parity are set in the Modbus driver of the
master and / or the slaves. The Modbus standard has two communications
modes, RTU and ASCII. However, CR200(X)s communicate in RTU mode
exclusively.

Field instruments can be queried by the CR200(X). Because Modbus has a set
command structure, programming the CR200(X) to get data from field
instruments is much simpler than from serial sensors. Because Modbus uses a
common bus and addresses each node, field instruments are effectively
multiplexed to a CR200(X) without additional hardware.

A CR200(X) goes into sleep mode after 40 seconds of communications

inactivity. Once asleep, two packets are required before the CR200(X) will
respond. The first packet awakens the CR200(X); the second packet is received
as data.

15.1.2 Terminology
TABLE. Modbus to Campbell Scientific Equivalents (p. 139) lists terminology
equivalents to aid in understanding how CR200(X)s fit into a SCADA system.

Table 19. Modbus to Campbell Scientific Equivalents

Modbus Domain Data Form Campbell Scientific Domain
Coils Single Bit Ports, Flags, Boolean Variables
Digital Registers 16-bit Word Floating Point Variables
Input Registers 16-bit Word Floating Point Variables
Holding Registers 16-bit Word Floating Point Variables
RTU / PLC CR200(X)
Master Usually a computer
Slave Usually a CR200(X)
Field Instrument Sensor

139
Section 15. Alternate Telecoms Resource Library

15.1.2.1 Glossary of Terms

Coils (00001 to 09999)
Originally, "coils" referred to relay coils. In CR200(X)s, coils are
exclusively ports, flags, or a Boolean variable array. Ports are inferred if
parameter 5 of the ModbusSlave instruction is set to 0. Coils are assigned to
Modbus registers 00001 to 09999.

Digital Registers 10001-19999

Hold values resulting from a digital measurement. Digital registers in the
Modbus domain are read only. In the CSI domain, the leading digit in
Modbus registers is ignored, and so are assigned together to a single Dim or
Public variable array (read / write).

Input Registers 30001 - 39999

Hold values resulting from an analog measurement. Input registers in the
Modbus domain are read only. In the CSI domain, the leading digit in
Modbus registers is ignored, and so are assigned together to a single Dim or
Public variable array (read / write).

Holding Registers 40001 - 49999

Hold values resulting from a programming action. Holding registers in the
Modbus domain are read / write. In the CSI domain, the leading digit in
Modbus registers is ignored, and so are assigned together to a single Dim or
Public variable array (read / write).

RTU / PLC
Remote Telemetry Units (RTUs) and Programmable Logic Controllers
(PLCs) were at one time used in exclusive applications. As technology
increases, however, the distinction between RTUs and PLCs becomes more
blurred. A CR200(X) fits both RTU and PLC definitions.

15.1.3 Programming for Modbus

15.1.3.1 Declarations
TABLE. CRBASIC Ports, Flags, Variables and Modbus Registers (p. 141)
shows the linkage between CR200(X) ports, flags and Boolean variables and
Modbus registers. Modbus does not distinguish between CR200(X) ports, flags,
or Boolean variables. By declaring only ports, or flags, or Boolean variables, the
declared feature is addressed by default. A typical CRBASIC program for a
Modbus application will declare variables and ports, or variables and flags, or
variables and Boolean variables.

140
 Section 15. Alternate Telecoms Resource Library

Table 20. CRBASIC Ports, Flags, Variables and Modbus Registers

Example CRBASIC Equivalent Example
CR200(X) Feature Declaration Modbus Register
Control Port (Port) Public Port(8) 00001 to 00009
Flag Public Flag(17) 00001 to 00018
Boolean Variable Public ArrayB(56) as Boolean 00001 to 00057
Variable Public ArrayV(20)* 40001 to 40041* or
30001 to 30041*
*Because of byte number differences, each CR200(X) domain variable translates to two Modbus domain input / holding
registers.

15.1.3.2 CRBASIC Instructions - Modbus

Complete descriptions and options of commands are available in CRBASIC
Editor Help.
ModbusMaster ()
Sets up a CR200(X) as a Modbus master to send or retrieve data from a Modbus
slave.
Syntax
ModbusMaster (ResultCode, ComPort, BaudRate,
ModbusAddr, Function, Variable, Start, Length,
Tries, TimeOut)

ModbusSlave ()
Sets up a CR200(X) as a Modbus slave device.
Syntax
ModbusSlave (ComPort, BaudRate, ModbusAddr,
DataVariable, BooleanVariable)

15.1.3.3 Addressing (ModbusAddr)

Modbus devices have a unique address in each network. Addresses range from 1
to 247. Address 0 is reserved for universal broadcasts. When using the NL100,
use the same number as the Modbus and PakBus® address.

15.1.3.4 Supported Function Codes (Function)

Modbus protocol has many function codes. CR200(X) commands support the
following.

• 01 Read Coil Status

• 02 Read Input Status

• 03 Read Holding Registers

• 04 Read Input Registers

141
Section 15. Alternate Telecoms Resource Library

• 05 Force Single Coil

• 15 Force Multiple Coils

• 16 Force Multiple Registers

15.1.3.5 Reading Inverse Format Registers

Some Modbus devices require reverse byte order words (CDAB vs. ABCD).
This can be true for either floating point, or integer formats. While other
CRBasic dataloggers, such as the CR1000, can use the MoveBytes() instruction
to output reverse byte order words, the CR200(X) does not have that capability.
If reverse byte order words are required, either the master has to make an
adjustment, which is sometimes possible, or the CR200(X) needs to replaced
with a datalogger that supports the MoveBytes() instruction.

15.1.4 Troubleshooting
Test Modbus functions on the CR200(X) with third party Modbus software.
Further information is available at the following links:

• www.simplyModbus.ca/FAQ.htm (http://www.simplymodbus.ca/faq.htm)

• www.Modbus.org/tech.php (http://www.modbus.org/tech.php)

• www.lammertbies.nl/comm/info/modbus.html
(http://www.lammertbies.nl/comm/info/modbus.html)

142
Section 16. Support Software
PC / Windows® compatible software products are available from Campbell
Scientific to facilitate CR200(X) programming, maintenance, data retrieval, and
data presentation. Short Cut, PC200W, and Visual Weather are designed for
novice integrators, but have features useful in advanced applications. PC400 and
LoggerNet provide increasing levels of power required for advanced integration,
programming and networking applications. Support software for PDA and
Linux applications are also available.

A recent addition to the support software line-up is the Campbell Scientific

Network Planner, which assists in the configuration of networks.

16.1 Short Cut

Short Cut utilizes an intuitive user interface to create CR200(X) program code
for common measurement applications. It presents lists from which sensors,
engineering units, and data output formats are selected. It supports by name
most sensors sold by Campbell Scientific. It features "generic" measurement
routines, enabling it to support many sensors from other manufacturers.
Programs created by Short Cut are automatically well documented and produce
examples of CRBASIC programming that can be used as source or reference
code for more complex programs edited with CRBASIC Editor.

Short Cut is included with PC200W, Visual Weather, PC400, RTDAQ, and
LoggerNet and is available at no charge from the Campbell Scientific web site.

16.2 PC200W
PC200W utilizes an intuitive user interface to support direct serial
communication to the CR200(X) via COM / RS-232 ports. It sends programs,
collects data, and facilitates monitoring of digital measurement and process
values. PC200W is available at no charge from the Campbell Scientific web
site.

16.3 Visual Weather

Visual Weather supports weather stations. It is recommended in applications
wherein the user requires minimal control over programming and the pre-
configured display and reporting features. Visual Weather is highly integrated
and easy to use.

143
Section 16. Support Software

16.4 PC400
PC400 is a mid-level software suite. It includes CRBASIC Editor, point-to-point
communications over several communications protocols, simple real-time
digital and graphical monitors, and report generation. It does not support
scheduled collection or multi-mode communication networks.

16.5 RTDAQ
RTDAQ is targeted for industrial and other high-speed data acquisition
applications.

16.6 LoggerNet Suite

The LoggerNet suite utilizes a client-server architecture that facilitates a wide
range of applications and enables tailoring software acquisition to specific
requirements. TABLE. LoggerNet Products that Include the LoggerNet Server
(p. 144) lists features of LoggerNet products that include the LoggerNet server.
TABLE. LoggerNet Clients (p. 145) lists features of LoggerNet products that
require the LoggerNet server as an additional purchase.

Table 21. LoggerNet Products that Include the LoggerNet Server

LoggerNet Datalogger management, programming, data collection, scheduled data
collection, network monitoring and troubleshooting, graphical data displays,
automated tasks, data viewing and post-processing.
LoggerNet Admin All LoggerNet features plus network security, manages the server from a
remote PC, runs LoggerNet as a service, exports data to third party
applications, launches multiple instances of the same client, e.g., two or
more functioning Connect windows.
LoggerNet Remote Allows management of an existing LoggerNet datalogger network from a
remote location, without investing in another complete copy of LoggerNet
Admin.
LoggerNet-SDK Allows software developers to create custom client applications that
communicate through a LoggerNet server with any datalogger supported by
LoggerNet. Requires LoggerNet.
LoggerNet Server - SDK Allows software developers to create custom client applications that
communicate through a LoggerNet server with any datalogger supported by
LoggerNet. Includes the complete LoggerNet Server DLL, which can be
distributed with the custom client applications.
LoggerNet Linux Includes LoggerNet Server for use in a Linux environments and LoggerNet
Remote for managing the server from a Windows environment.

144
 Section 16. Support Software

Table 22. LoggerNet Clients

These LoggerNet clients require, but are not sold with, the
LoggerNet Server.
Baler Handles data for third-party application feeds.
RTMCRT RTMC viewer only.
RTMC Web Server Converts RTMC graphics to HTML.
RTMC Pro Enhanced version of RTMC.
LoggerNetData Displays / Processes real-time and historical data.
CSI OPC Server Feeds data into third-party OPC applications.

16.7 PDA Software

PConnect Software supports PDAs with Palm Operating Systems. PConnectCE
supports Windows Mobile and Pocket PC PDAs. Both support direct RS-232
connection to the CR200(X) for sending programs, collecting data, and digital
real-time monitoring.

16.8 Network Planner

Network Planner is a "drag and drop" application used in designing PakBus
datalogger networks. The user interacts with Network Planner through a
drawing canvas upon which are placed PCs and dataloggers nodes. Links
representing various telecommunications options are drawn between nodes.
Activities to take place between the nodes are specified. Network Planner
automatically specifies settings for individual devices and creates XML files for
download to each device through DevConfig.

145
Section 16. Support Software

146
Section 17. Care and Maintenance
Temperature and humidity can affect the performance of the CR200(X). The
internal lithium battery must be replaced periodically. Factory replacement is
recommended. Contact Campbell Scientific to obtain an RMA prior to shipping
the CR200(X).

17.1 Temperature Range

The CR200(X) is designed to operate reliably from -40ºC to +50°C in non-
condensing environments.

17.2 Moisture Protection

When humidity tolerances are exceeded and condensation occurs, damage to IC
chips, microprocessor failure, and/or measurement inaccuracies due to
condensation on the various PC board runners may result. Effective humidity
control is the responsibility of the user.

Adequate desiccant should be placed in the instrumentation enclosure to prevent

corrosion on the CR200(X) wiring panel. The desiccant needs to be replaced or
dried out frequently enough to control the humidity.

17.3 Enclosures
Campbell Scientific offers environmental enclosures for housing a CR200(X)
and peripherals. These enclosures are classified as NEMA 4X (watertight, dust-
tight, corrosion-resistant, indoor and outdoor use). Refer to APPENDIX.
Enclosures (Appendix p. 31) for information concerning available enclosures.

147
Section 17. Care and Maintenance

Figure 52: Enclosure

17.4 Replacing the Internal Battery

Caution Fire, explosion, and severe burn hazard! Misuse or improper
installation of the lithium battery can cause severe injury. Do not
recharge, disassemble, heat above 100°C (212°F), solder directly to the
cell, incinerate, or expose contents to water. Dispose of spent lithium
batteries properly.

The CR200(X) contains a lithium battery that operates the clock and SRAM
when the CR200(X) is not powered. The CR200(X) does not draw power from
the lithium battery while it is powered by an external source. In a CR200(X)
stored at room temperature, the lithium battery should last approximately 5
years (less at temperature extremes). Where the CR200(X) is powered most or
all of the time the lithium cell should last much longer.

The internal lithium battery must be replaced periodically. Factory replacement

is recommended. Contact Campbell Scientific to obtain an RMA prior to
shipping the CR200(X).

If the lithium cell is removed or allowed to discharge below the safe level, the
CR200(X) will still operate correctly while powered. Without the lithium
battery, the clock will reset and data is lost when power is removed.

148
 Section 17. Care and Maintenance

A replacement lithium battery can be purchased from Campbell (part number

15598). TABLE. CR200(X) Lithium Battery Specifications p. 33 lists the
specifications of the battery. However, Campbell Scientific recommends that the
battery be replaced at the factory.

Table 23. Internal Lithium Battery Specifications

Manufacturer Renata
Model CR2016 (3.6V)
Capacity 80 mAh
Self-discharge rate 1%/year @ 23°C
Operating temperature range -40°C to +85°C

149
Section 17. Care and Maintenance

150
Section 18. Troubleshooting
Note If any component needs to be returned to the factory for repair or
recalibration, remember that an RMA number is required. Contact a Campbell
Scientific applications engineer to receive the RMA number.

18.1 Programming
A properly deployed CR200(X) measures sensors accurately and stores all data
as instructed by its program. Experienced users analyze data soon after
deployment to ensure the CR200(X) is measuring and storing data as intended.
Most measurement and data storage problems are a result of one or more
instances of improper program code or "bugs."

18.1.1.1 Status Table as Debug Resource

Consult the CR200(X) Status Table when developing a program or when a
problem with a program is suspected.

Read More! See APPENDIX. Status Table and Settings p. 15 for a complete list
of Status Table registers and hints on using the Status Table.

18.1.1.2 SkippedScan
Skipped scans are caused by long programs with short scan intervals or when
other operations occupy the processor at a scan's start time. Occasional skipped
scans may be acceptable but should be avoided. Skipped scans may compromise
frequency measurements made with pulse channels. The error occurs because
counts from a scan and subsequent skipped scans are regarded by the CR200(X)
as having occurred during a single scan. The measured frequency can be much
higher than actual. Be careful that scans that store data are not skipped. If any
scan skips repeatedly, optimization of the datalogger program or reduction of
online processing may be necessary.

18.1.1.3 VarOutOfBounds
Indicates the number of variables that are out of bounds, meaning the
dimensioned array is not large enough to store the variable. When this value is
non-zero, edit the program and increase the array size.

18.1.1.4 WatchdogErrors
Non-zero indicates the CR200(X) has crashed, which can be caused by power or
transient voltage problems, or an operating system or hardware problem.
Watchdog errors may cause telecommunications disruptions, which can make
diagnosis and remediation difficult. Sometimes a TrapCode will accompany a
WatchDogCnt.

151
Section 18. Troubleshooting

18.1.1.5 TrapCode
Normally this value is zero. If set to a value of 16, TrapCode indicates an
EEPROM memory failure. When this occurs the datalogger stops running its
program and the red LED flashes twice per scan interval. The datalogger must
be returned to CSI to replace the Serial Flash EEPROM. Contact a Campbell
Scientific applications engineer to receive an RMA number.

18.1.1.6 Compile and Download Errors

When a user program is compiled , it is checked for errors. Errors caught by the
compiler are termed “Compile Errors.” Because CR200(X) programs are
compiled externally by the datalogger support software, most programming
errors are found before the program reaches the CR200(X). A program wherein
no compile errors are found may still have errors only detectable after the
program reaches the CR200(X). These errors are “Download Errors.” TABLE.
Program Download Errors p. 152 lists possible error messages and conditions.

Table 24. Program Download Errors

Download Error / Condition Error Meaning Notes
"No Prog Running" Flash memory holding the program
has been erased.
"Wrong OS Ver" Program was compiled in the Compiler executable file
CRBASIC Editor with an incorrect (C:\Campbellsci\Lib\ CR200Compilers
(usually older) compiler executable \cr2compvxxxx.exe) must match the
that does not match the operating
CR200(X) operating system
system resident in the CR200(X).
(cr2osvxxxx.a43), where xxxx is the
operating system version number.
Compiler executable version is shown on
the first line of the compile results in
CRBASIC Editor.

This error typically occurs only when forcing

a .BIN file to be sent to the
CR200(X). By default, datalogger support
software "sends" the .CR2 file,
automatically matching OS and compiler.

Current compilers can be obtained at

www.campbellsci.com.
"Wrong Prog" Program down load started then was Attempt to re-send program.
either aborted or not completed
because of a communication error,
etc.
"Prog Corrupt" Program is corrupt or damaged. When power is cycled, program is re-loaded
from FLASH. If program stored in FLASH
becomes corrupt, this error may occur.
"Flash Erased" Flash area has been erased When power is cycled, program is re-loaded
from FLASH. If FLASH has been erased
because of a system problem, this error
may occur.
No error detected but program The CR200(X) may not have Check program memory requirements for
does not run. adequate memory. data tables and variables.
No error detected, program runs Often due to a short Scan() time. Increase the scan rate or remove lower
but malfunctions. priority instructions.

152
 Section 18. Troubleshooting

18.1.2 NAN and ±INF

NAN (not-a-number) and ±INF (infinite) are data words indicating an
exceptional occurrence in CR200(X) function or processing. NAN is a constant
that can be used in expressions such as in CRBASIC EXAMPLE. Using NAN in
Expressions (p. 153) NAN can also be used in the disable variable (DisableVar)
in output processing (data storage) instructions, as indicated in CRBASIC
EXAMPLE. Using NAN in Expressions p. 153.

CRBASIC EXAMPLE 21. Using NAN in Expressions

If WindDir = NAN Then
WDFlag = True
Else
WDFlag=False
EndIf

18.1.2.1 Measurements and NAN

A NAN indicates an invalid measurement.

18.1.2.1.1 Voltage Measurements

The CR200(X) measures voltage inputs ranging from 0 to 2500 mV. Input
signals that exceed this ranges result in an over range indicated by a NAN for
the measured result. A voltage input not connected to a sensor is floating and
the resulting measured voltage often remains near the voltage of the previous
measurement. Floating measurements tend to wander in time, and could
temporarily impersonate a valid measurement.

18.1.2.1.2 SDI-12 Measurements

SDI-12 Measurements

NAN is loaded into the first SDI12Recorder () variable under these conditions:

• When busy with terminal commands.

• When the command is an invalid command.

• When the sensor aborts with CR LF and there is no data.

18.1.2.2 Floating Point Math, NAN, and ±INF

TABLE. Math Expressions and CRBASIC Results (p. 154) lists math
expressions, their CRBASIC form, and IEEE floating point math result for the
CR200(X).

153
Section 18. Troubleshooting

Table 25. Math Expressions and CRBASIC Results

Expression CRBASIC Expression Result
0/0 0/0 NAN

∞-∞ (1 / 0) - (1 / 0) NAN
∞
(-1) -1 ^ (1 / 0) NAN

0 * -∞ 0 * (-1 * (1 / 0)) NAN

±∞ / ±∞ (1 / 0) / (1 / 0) NAN
∞
1 1 ^ (1 / 0) NAN

0*∞ 0 * (1 / 0) NAN

x/0 1/0 NAN

x / -0 1 / -0 NAN

-x / 0 -1 / 0 NAN
-x / -0 -1 / -0 NAN
0
∞ (1 / 0) ^ 0 1
∞
0 0 ^ (1 / 0) 0
0
0 0^0 1

18.2 Communications
18.2.1 RS-232
Baud rate mis-match between the CR200(X) and datalogger support software is
often the root of communication problems through the RS-232 port. Software
settings should be set to a baud rate of 9600.

18.2.2 Communicating with Multiple PC Programs

A common practice is to monitor the performance of a CR200(X) using
Devconfig or LoggerNet while the CR200(X) has an open connection to another
copy of LoggerNet. For example, the main connection can be via RF while the
performance monitoring is done via RS-232 port. This is a useful feature of the
CR200(X). A problem often arises, however, in that the CR200(X) gets
confused when attempting this via two different ports, from two different
instances of the same PakBus® address, i.e. if LoggerNet and Devconfig have
the same address.

Note LoggerNet defaults to PakBus® address 4094. Devconfig is fixed at

PakBus® address 4094.

The solution is to change the PakBus® address in LoggerNet | Setup | Options |

LoggerNet Pakbus Settings). If feasible, use PC200W or PC400 instead of
Devconfig as each has a different default PakBus® address from LoggerNet.

154
 Section 18. Troubleshooting

18.3 Power Supply

18.3.1 Overview
Power supply systems may include batteries, charger/regulators, and charging
sources such as solar panels or transformers. All of these components may need
to be checked if the power supply is not functioning properly.

Diagnosis and Fix Procedures (p. 156) includes the following flowcharts:

• Battery Voltage Test

• Charging Circuit Test (when using an unregulated solar panel)

• Charging Circuit Test (when using a transformer)

• Adjusting Charging Circuit

If all of the power supply components are working properly and the system has
peripheral(s) with high current drain(s) such as satellite transmitter, verify that
the system's power supply provides enough power. For more information, refer
to our Power Supply product literature or Application Note.

18.3.2 Troubleshooting at a Glance

Symptoms:
Possible symptoms include the CR200(X) program not executing;
WatchDogCnt in the Status table displaying a non-zero number.

Affected Equipment:
Batteries, charger/regulators, solar panels, transformers

Likely Cause:
Batteries may need to be replaced or recharged; charger/regulators may
need to be fixed or recalibrated; solar panels or transformers may need to be
fixed or replaced.

Required Equipment:
Voltmeter; 5 kohm resistor and 50 ohm 1 W resistor for the charging circuit
tests and to adjust the charging circuit voltage

155
Section 18. Troubleshooting

18.3.3 Diagnosis and Fix Procedures

18.3.3.1 Battery Voltage Test

156
 Section 18. Troubleshooting

18.3.3.2 Charging Circuit Test - Solar Panel

157
Section 18. Troubleshooting

18.3.3.3 Charging Circuit Test - Transformer

158
 Section 18. Troubleshooting

18.3.3.4 Adjusting Charging Circuit Voltage

159
Section 18. Troubleshooting

160
Appendix A. Glossary
A.1 Terms
AC
See VAC (Appendix p. 12).

A/D
Analog-to-digital conversion. The process that translates analog voltage
levels to digital values.

accuracy
A measure of the correctness of a measurement. See also Accuracy,
Precision, and Resolution (Appendix p. 13).

Amperes (Amps)
Base unit for electric current. Used to quantify the capacity of a power
source or the requirements of a power consuming device.

analog
Data presented as continuously variable electrical signals.

ASCII / ANSI
Abbreviation for American Standard Code for Information Interchange /
American National Standards Institute. An encoding scheme in which
numbers from 0-127 (ASCII) or 0-255 (ANSI) are used to represent pre-
defined alphanumeric characters. Each number is usually stored and
transmitted as 8 binary digits (8 bits), resulting in 1 byte of storage per
character of text.

asynchronous
The transmission of data between a transmitting and a receiving device
occurs as a series of zeros and ones. For the data to be "read" correctly, the
receiving device must begin reading at the proper point in the series. In
asynchronous communication, this coordination is accomplished by having
each character surrounded by one or more start and stop bits which
designate the beginning and ending points of the information (see
Synchronous (Appendix p. 11)).

baud rate
The speed of transmission of information across a serial interface,
expressed in units of bits per second. For example, 9600 baud refers to bits
being transmitted (or received) from one piece of equipment to another at a
rate of 9600 bits per second. Thus, a 7 bit ASCII character plus parity bit
plus 1 stop bit (total 9 bits) would be transmitted in 9/9600 sec. = .94 ms or
about 1000 characters/sec. When communicating via a serial interface, the

1
Appendix A. Glossary

baud rate settings of two pieces of equipment must match each other. The
baud rate for CR200(X) communication should be set to 9600.

Beacon
A signal broadcasted to other devices in a PakBus® network to identify
"neighbor" devices. A beacon in a PakBus® network ensures that all
devices in the network are aware of other devices that are viable. If
configured to do so, a clock set command may be transmitted with the
beacon. This function can be used to synchronize the clocks of devices
within the PakBus® network. See also PakBus (Appendix p. 7) and
Neighbor Device (Appendix p. 6).

binary
Describes data represented by a series of zeros and ones. Also describes the
state of a switch, either being on or off.

code
A CRBASIC program, or a portion of a program.

compile
The software process of converting a human readable program to binary
machine code. CR200(X) programs are compiled by the CRBASIC Editor.

constant
A packet of CR200(X) memory given an alpha-numeric name and assigned
a fixed number.

control I/O
Terminals C1 - C2 or processes utilizing these terminals.

CVI
Communications Verification Interval. The interval at which a PakBus®
device verifies the accessibility of neighbors in its neighbor list. If a
neighbor does not communicate for a period of time equal to 2.5 x the CVI,
the device will send up to 4 Hellos. If no response is received, the neighbor
is removed from the neighbor list.

CPU
Central processing unit. The brains of the CR200(X).

cr
Carriage Return

2
 Appendix A. Glossary

datalogger support software

Includes PC200W, PC400, RTDAQ, LoggerNet

data point
A data value which is sent to Final Storage as the result of an output
processing (data storage) instruction. Strings of data points output at the
same time make up a record in a data table.

DC
See VDC.

DCE
Data communications equipment. While the term has much wider meaning,
in the limited context of practical use with the CR200(X), it denotes the pin
configuration, gender and function of an RS-232 port. The RS-232 port on
the CR200(X) and on many 3rd party telecommunications devices, such as a
digital cellular modems, are DCE. Interfacing a DCE device to a DCE
device requires a null-modem cable.

desiccant
A material that absorbs water vapor to dry the surrounding air.

DevConfig
Device Configuration Utility, available with LN, PC400, or from the CSI
website.

differential
A sensor or measurement terminal wherein the analog voltage signal is
carried on two leads. The phenomenon measured is proportional to the
difference in voltage between the two leads.

digital
Numerically presented data.

Dim
A CRBASIC command for declaring and dimensioning variables. Variables
declared with DIM remain hidden during datalogger operation.

DTE
While the term has much wider meaning, in the limited context of practical
use with the CR200(X), it denotes the pin configuration, gender and
function of an RS-232 port. The RS-232 port on the CR200(X) and on
many 3rd party telecommunications devices, such as a digital cellular
modems, are DCE. Attachment of a null-modem cable to a DCE device
effectively converts it to a DTE device.

3
Appendix A. Glossary

Earth Ground
use of a grounding rod or another suitable device to tie a system or device
to the earth. Earth ground is a sink for electrical transients and possibly
damaging potentials, such as those produced by a nearby lightning strike.
Earth ground is the preferred reference potential for analog voltage
measurements. Note that most objects have a "an electrical potential" and
the potential at different places on the earth - even a few meters away - may
be different.

engineering units
Units that explicitly describe phenomena, as opposed to the CR200(X)
measurement units of millivolts or counts.

ESD
Electrostatic discharge

ESS
Environmental Sensor Station

excitation
Application of a precise voltage, usually to a resistive bridge circuit.

execution time
Time required to execute an instruction or group of instructions. If the
execution time of a Program Table exceeds the table's Execution Interval,
the Program Table is executed less frequently than programmed.

expression
A series of words, operators, or numbers that produce a value or result.

final storage
That portion of memory allocated for storing data tables with output arrays.
Final storage is a ring memory, with new data overwriting the oldest data.

garbage
The refuse of the data communication world. When data are sent or
received incorrectly (there are numerous reasons why this happens) a string
of invalid, meaningless characters (garbage) results. Two common causes
are: 1) a baud rate mismatch and 2) synchronous data being sent to an
asynchronous device and vice versa.

ground
Being or related to an electrical potential of 0 Volts.

4
 Appendix A. Glossary

Hello Exchange
The process of verifying a node as a neighbor.

Hertz
Abbreviated Hz. Unit of frequency described as cycles or pulses per second.

IEEE4
4 byte floating point data type.

INF
Infinite or undefined. A data word indicating the result of a function is
infinite or undefined.

input/output instructions
Used to initiate measurements and store the results in Input Storage or to set
or read Control/Logic Ports.

integer
A number written without a fractional or decimal component. 15 and 7956
are integers. 1.5 and 79.56 are not integers.

intermediate storage
That portion of memory allocated for the storage of results of intermediate
calculations necessary for operations such as averages or standard
deviations. Intermediate storage is not accessible to the user.

lf
line feed

loop counter
Increments by 1 with each pass through a loop.

manually initiated
Initiated by the user, as opposed to occurring under program control.

milli
The SI prefix denoting 1/1000s of a base SI unit.

Modbus
Communication protocol published by Modicon in 1979 for use in
programmable logic controllers (PLCs).

5
Appendix A. Glossary

modem/terminal
Any device which:

• has the ability to raise the CR200(X) ring line and put the CR200(X) in
the Telecommunications Command State

• has an asynchronous serial communication port which can be

configured to communicate with the CR200(X).

multi-meter
An inexpensive and readily available device useful in troubleshooting data
acquisition system faults.

mV
The SI abbreviation for milliVolts.

NAN
Not a number. A data word indicating a measurement or processing error.
Voltage over range, SDI-12 sensor error, and undefined mathematical
results can produce NAN.

Neighbor Device
Devices in a PakBus® network that can communicate directly with an
individual device without being routed through an intermediate device. See
PakBus (Appendix p. 7).

NIST
National Institute of Standards and Technology

Node
Part of the description of a datalogger network when using LoggerNet.
Each node represents a device that the communications server will dial
through or communicate with individually. Nodes are organized as a
hierarchy with all nodes accessed by the same device (parent node) entered
as child nodes. A node can be both a parent and a child.

Null-modem
A device, usually a multi-conductor cable, which converts an RS-232 port
from DCE to DTE or from DTE to DCE.

Ohm
The unit of resistance. Symbol is the Greek letter Omega (Ω). 1.0 Ω equals
the ratio of 1.0 Volt divided by 1.0 Amp.

6
 Appendix A. Glossary

Ohms Law
Describes the relationship of current and resistance to voltage. Voltage
equals the product of current and resistance (V = I*R).

on-line data transfer

Routine transfer of data to a peripheral left on-site. Transfer is controlled by
the program entered in the datalogger.

output
A loosely applied term. Denotes a) the information carrier generated by an
electronic sensor, b) the transfer of data from variable storage to final
storage, or c) the transfer of power from the CR200(X) or a peripheral to
another device.

output array
A string of data points output to Final Storage. Output occurs when the data
interval and data trigger are true. The data points which complete the Array
are the result of the Output Processing Instructions which are executed
while the Output Flag is set.

output interval
The time interval between initiations of a particular data table record.

output processing instructions

Process data values and generate Output Arrays. Examples of Output
Processing Instructions include Totalize, Maximum, Minimum, Average,
etc. The data sources for these Instructions are values in Input Storage. The
results of intermediate calculations are stored in Intermediate Storage. The
ultimate destination of data generated by Output Processing Instructions is
usually Final Storage but may be Input Storage for further processing. The
transfer of processed summaries to Final Storage takes place when the
Output Flag has been set by a Program Control Instruction.

PakBus
A proprietary telecommunications protocol similar in concept to internet
protocol (IP). It has been developed by Campbell Scientific to facilitate
communications between Campbell Scientific instrumentation.

parameter
Used in conjunction with CR200(X) program Instructions, parameters are
numbers or codes which are entered to specify exactly what a given
instruction is to do. Once the instruction number has been entered in a
Program Table, the CR200(X) will prompt for the parameters by displaying
the parameter number in the ID Field of the display.

7
Appendix A. Glossary

period average
A measurement technique utilizing a high-frequency digital clock to
measure time differences between signal transitions. Sensors commonly
measured with period average include vibrating wire transducers and water
content reflectometers.

peripheral
Any device designed for use with, and requiring, the CR200(X) (or another
CSI datalogger) to operate.

precision
A measure of the repeatability of a measurement. See also Accuracy,
Precision, and Resolution (Appendix p. 13).

print device
Any device capable of receiving output over pin 6 (the PE line) in a
receive-only mode. Printers, "dumb" terminals, and computers in a terminal
mode fall in this category.

print peripheral
See Print Device (Appendix p. 8).

processing instructions
These instructions allow the user to further process input data values and
return the result to Input Storage where it can be accessed for output
processing. Arithmetic and transcendental functions are included in these
Instructions.

program control instructions

Used to modify the sequence of execution of Instructions contained in
Program Tables; also used to set or clear flags.

Public
A CRBASIC command for declaring and dimensioning variables. Variables
declared with PUBLIC can be monitored during datalogger operation.

pulse
An electrical signal characterized by a sudden increase in voltage followed
by a short plateau and a sudden voltage decrease.

regulator
A device for conditioning an electrical power source. CSI regulators
typically condition AC or DC voltages greater than 16 V to about 14 VDC.

8
 Appendix A. Glossary

resistance
A feature of an electronic circuit that impedes or redirects the flow of
electrons through the circuit.

resistor
A device that provides a known quantity of resistance.

resolution
A measure of the fineness of a measurement. See also Accuracy, Precision,
and Resolution (Appendix p. 13).

ring line (Pin 3)

Line pulled high by an external device to "awaken" the CR200(X).

Ring Memory
A memory configuration for data tables allowing the oldest data to be
overwritten. This is the default setting for data tables.

RMA Number
Return Materials Authorization number. Obtain an RMA number from a
Campbell Scientific applications engineer PRIOR to sending any equipment
for repair.

RMS
Root mean square or quadratic mean. A measure of the magnitude of wave
or other varying quantities around zero.

RS-232
Recommended Standard 232. A loose standard defining how two
computing devices can communicate with each other. The implementation
of RS-232 in CSI dataloggers to PC communications is quite rigid, but
transparent to most users. Implementation of RS-232 in CSI datalogger to
RS-232 smart sensor communications is quite flexible.

sample rate
The rate at which measurements are made. The measurement sample rate is
primarily of interest when considering the effect of time skew (i.e., how
close in time are a series of measurements). The maximum sample rates are
the rates at which measurements are made when initiated by a single
instruction with multiple repetitions.

scan (execution interval)

The time interval between initiating each execution of a given Scan
interval. If the Execution Interval is evenly divisible into 24 hours (86,400
seconds), the Execution Interval is synchronized with 24 hour time, so that

9
Appendix A. Glossary

the table is executed at midnight and every execution interval thereafter.

The table is executed for the first time at the first occurrence of the
Execution Interval after compilation. If the Execution Interval does not
divide evenly into 24 hours, execution will start on the first even second
after compilation.

SDI-12
Serial/Digital Data Interface at 1200 bps. Communication protocol for
transferring data between data recorders and sensors.

SDM
Synchronous Device for Measurement. A processor based peripheral device
or sensor that communicates with the CR200(X) via hardwire over short
distance using a proprietary CSI protocol. The CR200(X) datalogger is not
compatible with SDM devices.

Send
Denotes the program send button in LoggerNet / PC400 / RTDAQ /
PC200W datalogger support software.

serial
A loose term denoting output or a device that outputs an electronic series of
alphanumeric characters.

SI Système Internationale
The International System of Units.

signature
A number which is a function of the data and the sequence of data in
memory. It is derived using an algorithm which assures a 99.998%
probability that if either the data or its sequence changes, the signature
changes.

single-ended
Denotes a sensor or measurement terminal where in the analog voltage
signal is carried on a single lead, which is measured with respect to ground.

skipped scans
Occurs when the CR200(X) program is too long for the scan interval.
Skipped scans can cause errors in pulse measurements.

SP
Space

10
 Appendix A. Glossary

state
Whether a device is on or off.

string
A datum consisting of alpha-numeric characters. CR200(X) dataloggers do
not support the STRING variable type.

support software
Includes PC200W, PC400, RTDAQ, LoggerNet.

synchronous
The transmission of data between a transmitting and receiving device
occurs as a series of zeros and ones. For the data to be "read" correctly, the
receiving device must begin reading at the proper point in the series. In
synchronous communication, this coordination is accomplished by
synchronizing the transmitting and receiving devices to a common clock
signal (see Asynchronous (Appendix p. 1)).

throughput
The throughput rate is the rate at which a measurement can be made, scaled
to engineering units, and the reading stored in a data table. The CR200(X)
has the ability to scan sensors at a rate exceeding the throughput rate. The
primary factor affecting throughput rate is the amount of processing
specified by the user. In a CR200(X) all processing called for by an
instruction must be completed before moving on the next instruction.

TLL
Transistor - Transistor Logic. A serial protocol using 0V and 5V as logic
signal levels.

toggle
To reverse the current power state.

UPS
Uninterruptible power supply. A UPS can be constructed for most
datalogger applications using AC line power, an AC/AC or AC/DC wall
adapter, a charge controller, and a rechargeable battery.

User Program
The CRBASIC program written by the CR200(X) user in CRBASIC Editor
or Short Cut.

variable
A packet of CR200(X) memory given an alpha-numeric name, which holds
a potentially changing number or string.

11
Appendix A. Glossary

VAC
Volts Alternating Current. Mains or grid power is high-level VAC, usually
110 VAC or 220 VAC at a fixed frequency of 50 Hz or 60 Hz. High-level
VAC is used as a primary power source for Campbell Scientific power
supplies. Do not connect high-level VAC directly to the CR200(X). The
CR200(X) measures varying frequencies of low-level VAC in the range of
±20 VAC.

VDC
Volts Direct Current. The CR200(X) operates with a nominal 12 VDC
power supply. It can supply nominal 12 VDC and variable excitation in the
5 VDC and 2.5 VDC range. It measures analog voltage in the 0 – 2.5 VDC
range and pulse voltage in the ±20 VDC range.

volt meter
An inexpensive and readily available device useful in troubleshooting data
acquisition system faults.

Volts
SI unit for electrical potential.

watch dog timer

An error checking system that examines the processor state, software
timers, and program related counters when the datalogger is running its
program. If the processor has bombed or is neglecting standard system
updates or if the counters are outside the limits, the watchdog timer resets
the processor and program execution. Voltage surges and transients can
cause the watchdog timer to reset the processor and program execution.
When the watchdog timer resets the processor and program execution, an
error count is incremented in the watchdogtimer entry of the status table. A
low number (1 to 10) of watchdog timer resets is of concern, but normally
indicates the user should just monitor the situation. A large number (>10) of
error accumulating over a short period of time should cause increasing
alarm since it indicates a hardware or software problem may exist. When
large numbers of watchdog timer resets occur, consult with a Campbell
Scientific applications engineer. See WatchdogErrors p. 151 for more
information.

weather tight
Describes an instrumentation enclosure impenetrable by common
environmental conditions. During extraordinary weather events, however,
seals on the enclosure may be breached.

XML
Extensible Markup Language.

12
 Appendix A. Glossary

A.2 Concepts
A.2.1 Accuracy, Precision, and Resolution
Three terms often confused are accuracy, precision, and resolution. Accuracy is
a measure of the correctness of a single measurement, or the group of
measurements in the aggregate. Precision is a measure of the repeatability of a
group of measurements. Resolution is a measure of the fineness of a
measurement. Together, the three define how well a data acquisition system
performs. To understand how the three relate to each other, consider "target
practice" as an analogy. FIGURE. Accuracy, Precision, and Resolution (p. 13)
shows four targets. The bull's eye on each target represents the absolute correct
measurement. Each shot represents an attempt to make the measurement. The
diameter of the projectile represents resolution.

Figure 53: Accuracy, Precision, and Resolution

The objective of a data acquisition system should be high accuracy, high

precision, and to produce data with resolution as high as appropriate for a given
application.

13
Appendix A. Glossary

14
Appendix B. Status Table and Settings
The CR200(X) status table contains system operating status information
accessible via PC software DevConfig, LoggerNet, PC400, RTDAQ, or
PC200W. TABLE. Common Uses of the Status Table (Appendix p. 15) lists
some of the more common uses of status table information. TABLE. Status
Table Fields and Descriptions (Appendix p. 16) is a comprehensive list of status
table variables with brief descriptions.

Status Table information is easily viewed by going to LoggerNet / PC400 /

RTDAQ / PC200W | Datalogger | Station Status. However, be aware that
information presented in Station Status is not automatically updated. Click the
refresh button each time an update is desired. Alternatively, use the Numeric
displays of the connect screen to show critical values and have these update
automatically, or use Devconfig, which polls the status table at regular intervals
without use of a refresh button. Note that a lot of comms and other activity is
needed to generate the Status Table, so if the CR200(X) is very tight on time,
just getting the Status Table itself repeatedly could push timing over the edge
and cause skipped scans.

Through the continued development of the operating system, the status table has
become quite large. A separate settings table has been introduced to slow the
growth of the status table. To maintain backward compatibility, settings first
included in the status table have been retained, but are also included in the
settings editor.

Feature or Status Field(s)

Suspect Constituent to Consult
Reset Data Tables ResetTables (Enter 8888)
Operating System OSVersion
OSDate
OSSignature
WatchdogCnt
CRBASIC Program ProgName
ProgSig
VarOutOfBounds
SkipScan
EEPROM Error TrapCode
Power Supply Battery
WatchdogCnt
PakBus PakBusAddress
Radio RFInstalled
RfNeAddress
RfHopSeq
RfPwrMode
Rf_ForceOn
Rf_Protocol
RfSignalLevel

15
Appendix B. Status Table and Settings

Table 26. Status Table Fields and Descriptions

Status Table Normal User can

Fieldname Description Variable Type Default Range change? Info Type
^32
RecNum Increments for successive _ 0 to 2 _ _
status table data records
TimeStamp Time the record was Time _ _ _
generated

ProgName Name of current (running) String _ _ _ Status

program.

OSVersion Version of the Operating String _ _ _ Status

System

OSDate Date OS was released. String _ _ _ Status

ProgName Name of current (running) String _ _ _ Status
program.

ProgSig Signature of the current Integer _ _ _ Status

running program file
including comments. Does
not change with operating
system changes.

CalOffset Calibration table of single Integer array of 18 _ close to 0 _ Calib

ended offset values. Each
integration / range
combination has a single
ended offset associated
with it. These numbers are
updated by the
background slow
sequence if needed in the
program.
1
PakBusAddress CR200(X) PakBus String 1 1 to 3999 Yes Config PB
address.

RfInstalled Indicates the model of RF Integer _ _ _ Status

radio installed
RfNetAddr Address of the RF network Integer 0 0 to 63 Yes ConfigPB
RfAddress Address of the RF radio Integer 0 0 to 1023 Yes ConfigPB

RfHopSeq RF hopping sequence for Integer 0 0 to 6 Yes ConfigPB

the RF network

RfPwrMode Powermode of the RF String _ _ _ ConfigPB

radio

Rf_ForceOn Any non-zero number will Integer 0 Yes ConfigPB

override the current power
mode and set it on.

Rf_Protocol Protocol to use in the RF Integer 1 1 or 2 Yes ConfigPB

network

RfSignalLevel RF signal level _ _ Status

16
 Appendix B. Status Table and Settings

Table 26. Status Table Fields and Descriptions

RfRXPakBusCnt Status

VarOutOfBounds Number of times an array Integer 0 0 Can Reset = Error

was accessed out of 0
2
bounds

SkipScan Number of skipped scans Integer 0 _ Can Reset = Error

that have occurred 0
because the datalogger
was not finished with the
previous scan

TrapCode Indicates a problem with Integer 0 0 or 16 _ Error

datalogger memory

WatchDogCnt Number of Watchdog Integer 0 0 Can Reset = Error

errors that have occurred 0
while running this
3
program

ResetTables Resets all the data tables Integer 0 _0 Can Reset = Status
in the datalogger when 8888
changed to 8888

BattVoltage Current value of the Float _ 7-16 Volts _ Measure

battery voltage.
Measurement is made in
the background
calibration.

ProgSignature Signature of the current Integer _ _ _ Status

running program file
including comments. Does
not change with operating
system changes.

1. Pak Bus Addresses 1 to 4094 are valid. Addresses >= 4000 are
generally used for a PC by PC200W, RTDAQ, PC400, or LoggerNet.

2. Watchdog errors are automatically reset upon compiling a new

program.

3. The Variable Out-of-Bounds error occurs when a program tries to write

to an array variable outside of its declared size. A programming error
causes this, so it should not be ignored. When the datalogger detects
that a write outside of an array is being attempted it does not perform
the write and increments the VOOB in the status table. The compiler
and pre-compiler can only catch things like reps too large for an array
etc. If an array is used in a loop or expression the pre-compiler does not
(in most cases cannot) check to see if an array is accessed out of
bounds (i.e. accessing an array with a variable index such as arr(index)
= arr(index-1), where index is a variable).

17
Appendix B. Status Table and Settings

Table 27. CR200(X) Settings

Settings are accessed through Campbell Scientific's Device Configuration Utility (DevConfig) for direct serial
connection, or through PakBusGraph for most telecommunications options.

Setting Description Default Entry

Max Packet Size Specified the maximum size packet in bytes that should ever be 100
sent to the device.
PakBus Address This setting specifies the PakBus® address for this device. The 1
value for this setting must be chosen such that the address of
the device is unique in the scope of the datalogger network.
Duplication of PakBus® addresses in two or more devices can
lead to failures and unpredictable behavior in the PakBus®
network. The following values are the default addresses of
various types of software and devices and should probably be
avoided:
Device PB Address
LoggerNet 4094
PC400 4093
PC200 4092
Visual Weather 4091
RTDAQ 4090
DevConfig 4089
NL100 678
All other devices 1
Radio Installed Specifies the model number of the MaxStream radio if it is
recognized by the datalogger. It will have a value of zero if
there is no radio recognized by the datalogger.
RF Network Address Specifies the radio network address of the built-in radio. This 0
setting should be set to match the network address for the
RF400 base used to communicate with the datalogger.
RF Address Specifies the address of the built-in radio. This value should 0
generally be set to match the same as the address of the
RF400 base used to communicated with the datalogger unless
that base is used to communicate with non-PakBus®
dataloggers (such as a CR10X).
RF Hop Sequence Specifies the hopping sequence that will be used for the built-in 0
radio. This value should be set to match the value of the same
setting for the RF400 base station used to communicate with
this datalogger
Ignore RF Power Mode If set to true (non-zero value), the RF power mode setting will 0
be ignored and the radio will be powered on all of the time.
RF Power Mode This setting specifies the power wait state that will be set in the 50
built-in radio. This setting must be set so that the standby mode
of the radio is consistent with any other CR200(X) or
RF400/RF410/Rf415 with which this station must communicate.

The power modes supported include the following:

No Radio
Indicates that there is no radio hardware recognized by the
datalogger. The datalogger will not accept this value as an
input, but will report it if there is no radio hardware detected.

Always On
Indicates that the radio receiver circuit should always be ready
to receive data.

18
 Appendix B. Status Table and Settings

Table 27. CR200(X) Settings

Settings are accessed through Campbell Scientific's Device Configuration Utility (DevConfig) for direct serial
connection, or through PakBusGraph for most telecommunications options.

Setting Description Default Entry

1 Sec
Indicates that the radio receiver is to use the one second duty
cycle.

8 Sec
Indicates that the radio receiver is to use the eight second duty
cycle.

1 Sec with Long Header

Indicates that the radio receiver will use the one second duty
cycle and that the radio will transmit a one second long header
before sending data if the time since last transmission is over
one second.

8 Sec with Long Header

Indicates that the radio receiver will use the eight second duty
cycle and that the radio will transmit an eight second long
header if the time since the last transmission is greater than
eight seconds.

Pin Enabled
Indicates that the radio receiver is to be turned on only when
the RF_ForceOn status table variable is enabled.
Company Identifies the manufacturer CSI
PakCtrl Command Codes Identifies the list of PakBus PakCtrl Interface command codes 2 7 8 9 12
that the logger will accept.
BMP5 Command Codes Identifies the list of PakBus BMP5 Interface command codes 9 23 24 26 27 28 29
that the datalogger will accept. 30
Model Number Identifies the model number assigned to this datalogger CR2xx
RF Protocol Identifies the radio protocol that will be used for the CR2xx. In Transparent
order to be compatible with other CR2xx and RF400 type
devices, the default value of transparent must be used. The
following values are supported:

Transparent
This mode is compatible with older CR205 and RF400
operating systems.

PakBus Aware
This mode can be used in networks involving
RF401/RF411/RF416 hardware or other, newer CR20x,
CR211/CR216 devices and makes use of the retry capability
inherent in the MaxStream radios. This mode is not compatible
with the older radios.

19
Appendix B. Status Table and Settings

20
Appendix C. Serial Port Pin Outs
C.1 RS-232 Communications Port
C.1.1 Pin-Out
Pin configuration for the CR200(X) RS-232 9-pin port is listed in TABLE.
CR200(X) RS-232 Pin-Out p. 21.

The CR200(X) RS-232 port is a DCE (Data Communication Equipment) device.

A limited version of the RS-232 port is supported with no hardware flow
control. The most common use of the Datalogger's RS-232 port is a connection
to a computer DTE device. A standard DB9-to-DB9 cable can connect the
computer DTE device to the Datalogger DCE device.

The CR200(X) RS-232 port is not electrically isolated. Connection to an AC

powered computer may cause ground loops leading to measurement problems.

Maximum input = ±25 V

Maximum Output = ±13 V

Typical Output = ±5.4 V

The following table describes the Datalogger's RS-232 pin function with
standard DCE naming notation.

Table 28. CR200(X) RS-232 Pin-Out

PIN: Pin number
O: Signal Out of the CR200(X) to a RS-232 device
I: Signal Into the CR200(X) from a RS-232 device
PIN DCE Function Logger Function I/O Description
1 N/A Not Connected

2 TX TXD O Asynchronous data Transmit

3 RX RXD I Asynchronous data Receive

4 N/A Not Connected

5 GND GND Ground

6 DSR DTR O Data Terminal Ready

7 N/A Not Connected

8 CTS RTS O Request to send

9 N/A Not Connected

21
Appendix C. Serial Port Pin Outs

22
Appendix D. ASCII / ANSI Table
American Standard Code for Information Interchange (ASCII) / American
National Standards Institute (ANSI)

Decimal and Hexadecimal Codes and Characters Used with CR200(X) Tools

Keyboard Hyper- Keyboard Hyper-

Display LoggerNet Terminal Display LoggerNet Terminal
Dec Hex Char Char Char Dec Hex Char Char Char
0 0 NULL NULL 128 80 € Ç

1 1 ☺ 129 81 ü

2 2 ☻ 130 82 ‚ é

3 3 ♥ 131 83 ƒ â

4 4 ♦ 132 84 „ ä

5 5 ♣ 133 85 … à

6 6 ♠ 134 86 † å

7 7 • 135 87 ‡ ç

8 8 ◘ 136 88 ˆ ê

9 9 ht 137 89 ‰ ë

10 a lf lf 138 8a Š è

11 b vt 139 8b ‹ ï

12 c ff 140 8c Œ î

13 d cr cr 141 8d ì

14 e ♫ 142 8e Ž Ä

15 f ☼ 143 8f Å

16 10 ► 144 90 É

17 11 ◄ 145 91 ' æ

18 12 ↕ 146 92 ' Æ

19 13 ‼ 147 93 " ô

20 14 ¶ 148 94 " ö

21 15 § 149 95 • ò

22 16 ▬ 150 96 - û

23 17 ↨ 151 97 - ù

24 18 ↑ 152 98 ˜ ÿ

25 19 ↓ 153 99 ™ Ö

26 1a → 154 9a š Ü

27 1b 155 9b › ¢

23
Appendix D. ASCII / ANSI Table

Keyboard Hyper- Keyboard Hyper-

Display LoggerNet Terminal Display LoggerNet Terminal
Dec Hex Char Char Char Dec Hex Char Char Char
28 1c ∟ 156 9c œ £

29 1d ↔ 157 9d ¥

30 1e ▲ 158 9e ž Pt

31 1f ▼ 159 9f Ÿ ƒ

32 20 SP SP 160 a0 á

33 21 ! ! ! 161 a1 ¡ í

34 22 " " " 162 a2 ¢ ó

35 23 # # # 163 a3 £ ú

36 24 $ $ $ 164 a4 ¤ ñ

37 25 % % % 165 a5 ¥ Ñ

38 26 & & & 166 a6 ¦ ª

39 27 ' ' ' 167 a7 § º

40 28 ( ( ( 168 a8 ¨ ¿

41 29 ) ) ) 169 a9 © ⌐

42 2a * * * 170 aa ª ¬

43 2b + + + 171 ab « ½

44 2c , , , 172 ac ¬ ¼

45 2d - - - 173 ad ¡

46 2e . . . 174 ae ® «

47 2f / / / 175 af ¯ »

48 30 0 0 0 176 b0 ° ░

49 31 1 1 1 177 b1 ± ▒

50 32 2 2 2 178 b2 ² ▓

51 33 3 3 3 179 b3 ³ │

52 34 4 4 4 180 b4 ´ ┤

53 35 5 5 5 181 b5 µ ╡

54 36 6 6 6 182 b6 ¶ ╢

55 37 7 7 7 183 b7 · ╖

56 38 8 8 8 184 b8 ¸ ╕

57 39 9 9 9 185 b9 ¹ ╣

58 3a : : : 186 ba º ║

59 3b ; ; ; 187 bb » ╗

60 3c < < < 188 bc ¼ ╝

61 3d = = = 189 bd ½ ╜

62 3e > > > 190 be ¾ ╛

24
 Appendix D. ASCII / ANSI Table

Keyboard Hyper- Keyboard Hyper-

Display LoggerNet Terminal Display LoggerNet Terminal
Dec Hex Char Char Char Dec Hex Char Char Char
63 3f ? ? ? 191 bf ¿ ┐

64 40 @ @ @ 192 c0 À └

65 41 A A A 193 c1 Á ┴

66 42 B B B 194 c2 Â ┬

67 43 C C C 195 c3 Ã ├

68 44 D D D 196 c4 Ä ─

69 45 E E E 197 c5 Å ┼

70 46 F F F 198 c6 Æ ╞

71 47 G G G 199 c7 Ç ╟

72 48 H H H 200 c8 È ╚

73 49 I I I 201 c9 É ╔

74 4a J J J 202 ca Ê ╩

75 4b K K K 203 cb Ë ╦

76 4c L L L 204 cc Ì ╠

77 4d M M M 205 cd Í ═

78 4e N N N 206 ce Î ╬

79 4f O O O 207 cf Ï ╧

80 50 P P P 208 d0 Ð ╨

81 51 Q Q Q 209 d1 Ñ ╤

82 52 R R R 210 d2 Ò ╥

83 53 S S S 211 d3 Ó ╙

84 54 T T T 212 d4 Ô ╘

85 55 U U U 213 d5 Õ ╒

86 56 V V V 214 d6 Ö ╓

87 57 W W W 215 d7 × ╫

88 58 X X X 216 d8 Ø ╪

89 59 Y Y Y 217 d9 Ù ┘

90 5a Z Z Z 218 da Ú ┌

91 5b [ [ [ 219 db Û █

92 5c \ \ \ 220 dc Ü ▄

93 5d ] ] ] 221 dd Ý ▌

94 5e ^ ^ ^ 222 de Þ ▐

95 5f _ _ _ 223 df ß ▀

96 60 ` ` ` 224 e0 à α

97 61 a a a 225 e1 á ß

25
Appendix D. ASCII / ANSI Table

Keyboard Hyper- Keyboard Hyper-

Display LoggerNet Terminal Display LoggerNet Terminal
Dec Hex Char Char Char Dec Hex Char Char Char
98 62 b b b 226 e2 â Γ

99 63 c c c 227 e3 ã π

100 64 d d d 228 e4 ä Σ

101 65 e e e 229 e5 å σ

102 66 f f f 230 e6 æ µ

103 67 g g g 231 e7 ç τ

104 68 h h h 232 e8 è Φ

105 69 i i i 233 e9 é Θ

106 6a j j j 234 ea ê Ω

107 6b k k k 235 eb ë δ

108 6c l l l 236 ec ì ∞

109 6d m m m 237 ed í φ

110 6e n n n 238 ee î ε

111 6f o o o 239 ef ï ∩

112 70 p p p 240 f0 ð ≡

113 71 q q q 241 f1 ñ ±

114 72 r r r 242 f2 ò ≥

115 73 s s s 243 f3 ó ≤

116 74 t t t 244 f4 ô ⌠

117 75 u u u 245 f5 õ ⌡

118 76 v v v 246 f6 ö ÷

119 77 w w w 247 f7 ÷ ≈

120 78 x x x 248 f8 ø °

121 79 y y y 249 f9 ù ·

122 7a z z z 250 fa ú ·

123 7b { { { 251 fb û √

124 7c | | | 252 fc ü ⁿ

125 7d } } } 253 fd ý ²

126 7e ~ ~ ~ 254 fe þ ■

127 7f ⌂ 255 ff ÿ

26
Appendix E. Antenna Usage and
Compliance
E.1 Use of Antenna with CR200(X)
An FCC authorized antenna is required for use with CR200(X) models that have
a built-in radio. Several models are available from Campbell Scientific.

These antennas have been tested at an authorized FCC open-field test site and
are certified to be in compliance with FCC emissions limits. All antennas or
antenna cables have an SMA female connector for connection to the CR200(X).
The use of an unauthorized antenna could cause transmitted field strengths in
excess of FCC rules, interfere with licensed services, and result in FCC
sanctions against user.

E.2 Part 15 FCC Compliance Warning

Changes or modifications to the CR200(X) series radio systems not expressly
approved by Campbell Scientific, Inc. could void the user’s authority to operate
this product.

Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

27
Appendix E. Antenna Usage and Compliance

E.2.1 Use of Approved Antennas

FCC OET Bulletin No. 63 (October 1993)

Changing the antenna on a transmitter can significantly increase, or decrease,

the strength of the signal that is ultimately transmitted. Except for cable
locating equipment, the standards in Part 15 are not based solely on output
power but also take into account the antenna characteristics. Thus, a low power
transmitter that complies with the technical standards in Part 15 with a particular
antenna attached can exceed the Part 15 standards if a different antenna is
attached. Should this happen it could pose a serious interference problem to
authorized radio communications such as emergency, broadcast, and air-traffic
control communications.

Caution: In order to comply with the FCC RF exposure requirements, the

CR200(X) series may be used only with approved antennas
that have been tested with the on-board radio and a
minimum separation distance of 20 cm must be maintained
from the antenna to any nearby persons.

28
Appendix F. Sensors and Peripherals
Campbell Scientific sensors, power supplies, and peripherals expand the
measurement and control capability of the CR200(X). Consult product literature
at www.campbellsci.com or a Campbell Scientific applications engineer to
determine what peripherals are most suited to particular applications. Listings
below are not exhaustive and are current as of the manual publication date.

F.1 Sensors
Most electronic sensors will interface with the CR200(X). The following
sensors are available from Campbell Scientific and are easily integrated into
CR200(X) systems. Please contact Campbell Scientific for specific model
numbers.

Table 29. Sensors available from Campbell Scientific

Air Temperature Precipitation
Relative Humidity Road Weather
Barometric Pressure Soil Heat Flux
Conductivity Soil Temperature
Dissolved Oxygen Soil Volumetric Water Content
Distance Soil Water Potential
Duff Moisture Solar Radiation
Electrical Current Strain
Electric Field Surface Temperature
Fuel Moisture and Temperature Turbidity
Geographic Position Water Level

Heat, Vapor, and CO2 Flux Water Quality

Leaf Wetness Water Temperature

ORP / pH Wind Speed / Wind Direction

F.2 Dataloggers
Other Campbell Scientific datalogging devices can be used in networks with the
CR200(X). Data and control signals can pass from device to device with the
CR200(X) functioning as a leaf node in PakBus® networks.

29
Appendix F. Sensors and Peripherals

Table 30. Dataloggers available from Campbell Scientific

Model Description
CR200(X) Series Datalogger
CR800 Series Measurement and Control Datalogger
CR1000 Measurement and Control System
®
CR3000 Micrologger

F.3 Power Supplies

Several power accessories are available from Campbell Scientific to power the
CR200(X).

F.3.1 Batteries
Table 31. Batteries available from Campbell Scientific
Model / Part Number Description
16869 CR200(X) 12 Volt 0.8 Ahr Sealed Rechargeable Battery
with Connector
BPALK D-Cell 12 Volt Alkaline Battery Pack
BP12 12 Amp-Hour Sealed Rechargeable Battery (requires
regulator & primary source). Includes mounting bracket for
CSI enclosures.

BP24 24 Amp-Hour Sealed Rechargeable Battery (requires

regulator & primary source). Includes mounting bracket for
CSI enclosures.

F.3.2 Primary Sources

Table 32. Primary Power Sources available from Campbell Scientific
Model Description
9591 18 Vac 1.2 Amp Wall Plug Charger (accepts 110 Vac
mains power, requires regulator)

14014 18 Vdc Wall Plug Charger (accepts 90-264 Vac mains

power, requires regulator)

SP5 5-Watt Solar Panel (requires regulator)

SP10 10-Watt Solar Panel (requires regulator)

SP20 20-Watt Solar Panel (requires regulator)

SP5-L 5-Watt Solar Panel (requires regulator)

SP10R 10-Watt Solar Panel (includes regulator)
SP20R 20-Watt Solar Panel (includes regulator)
SP65 65-Watt Solar Panel (includes regulator)

30
 Appendix F. Sensors and Peripherals

F.4 Enclosures
Table 33. Enclosure available from Campbell Scientific
Model Description

ENC200 6.7" x 5.5" x 3.9" Weather Tight Enclosure

ENC10/12 10 inch x 12 inch Weather Tight Enclosure

ENC12/14 12 inch x 14 inch Weather Tight Enclosure

ENC14/16 14 inch x 16 inch Weather Tight Enclosure

ENC16/18 16 inch x 18 inch Weather Tight Enclosure

F.5 Relay Drivers

Relay drivers enable the CR200(X) to control large voltages.

Table 34. Relay Driver available from Campbell Scientific

Model Description
SW12V Single Switched 12V Control Circuit

F.6 Serial Cables, Adaptors and Switches

Table 35. Serial Cables, Adaptors and Switches available from Campbell
Scientific
Model Description
17394 RS-232 to USB Cable (not optically isolated)
COMCBL2-L Weatherproof Cable, 9-pin Male to 9-pin Female
10873 RS-232, 9-pin Female to 9-Pin Male, 6 ft

7026 RS-232 Cable, 9-pin Female to 25-pin Male, 6 ft

14413 RS-232 Cable, 9-pin Male to 25-pin Female

10871 RS-232 Adapter, 9-pin Male to 25-pin Female

15751 RS-232 Adapter, 9-pin Female to 25-pin Male

13657 Null Modem Cable DB9 Female-to-Female, 6 ft

18663 Null Modem Cable, 9-pin Male to 9-pin Male, 1 ft

SDS122 Two-way Serial Data Switch

17218 RJ45 to RS-232 Adapter

31
Appendix F. Sensors and Peripherals

F.7 Signal Conditioners

Signal conditioners modify or complete the output of a device to be compatible
with the CR200(X).

F.7.1 Current Shunt Modules

Table 36. Current Shunt Modules available from Campbell Scientific
Model Description
7977 100 ohm Shunt Resistor Assembly

F.8 Telecommunications Hardware

Table 37. Telecommunications Hardware available from Campbell Scientific
Model Description
RF401 100 mW spread spectrum radio modem

CR206(X) 100 mW spread spectrum radio enabled datalogger

CR211(X) 100 mW spread spectrum radio enabled datalogger
CR216(X) 100 mW spread spectrum radio enabled datalogger

F.8.1 Network Links

Table 38. Antennas for Spread Spectrum Radios available from Campbell
Scientific
Model Description
14310 900MHz 0dBd Omni 1/4 Wave Whip Antenna

14204 900MHz 0dBd Omni 1/2 Wave Whip Antenna

14221 900MHz 3dBd Omni Antenna

15970 900MHz 1dBd Dipole Antenna

14205 900MHz 6dBd Yagi Antenna

14201 900MHz 9dBd Yagi Antenna

16005 2.4GHz 0dBd Omni 1/2 Wave Whip Antenna

16755 2.4GHz 13 dBd Yagi Enclosed Antenna
17480 900MHz or 2.4GHz 1dBd Dipole Antenna

COAXRPSMA-L Antenna Cable LMR195 w/Reverse Polarity SMA & Type

N Male Connector
COAXNTN-L Antenna Cable RG8 w/2 Type N Male Connectors

32
 Appendix F. Sensors and Peripherals

F.8.2 Router and Leaf Node Hardware

Table 39. PakBus Leaf Node and Router Device Configuration

Network PakBus PakBus PakBus
Device Description Leaf Node Router Aware Transparent

CR200(X) Datalogger •

CR800 Datalogger • •

CR1000 Datalogger • •

CR3000 Datalogger • •

CR5000 Datalogger • •

LoggerNet Software •

NL100 Network Link • •

MD485 Multidrop • •

RF401 Radio • • •

F.8.3 Ap. Telecommunications Options

Table 40. CR200(X) Telecommunications Options

Destination Communications CSI
Device / Portal Path Carrier Model #
PC / COM or USB Direct Connect RS232 10873 or 17394
PDA / COM Port Direct Connect RS232 PCONNECT
PC / COM Port Digital Cellular 800 MHz RF RavenXXX
PC / COM Port Multidrop RS485 MD485

PC / Network Card Ethernet / PPP IP2 NL100

900 MHz &
PC / COM Port Spread Spectrum RF 2.4 GHz RF RF4XX
Satellite System Satellite Transceiver RF DCP200
Digital Display Direct Connect RS232 CD295

F.8.4 Network Links

Table 41. Network Links available from Campbell Scientific
Model Description
NL100 Does not use CR200(X) IP stack

RavenXXX PPP/IP key must be enabled

33
Appendix F. Sensors and Peripherals

F.9 Voltage Transient Suppressors

Table 42. Voltage Transient Suppressors available from Campbell Scientific
Model Description
14462 Surge Suppressor Kit for RF401 Radio & CR206(X)
Datalogger
19553 Surge Suppressor Kit for RF450 Radio
16982 Surge Suppressor Kit for RF416 Radio & CR216(X)
Datalogger
16981 Surge Suppressor Kit for GOES transmitters

SVP48 General Purpose Multi-line Surge Protector

34
Index
A Code • 2
Coil • 140
Abbreviations • 90 Collecting Data • 18
ac • 1 COM Port Connection • 11
ac Excitation • 6 Commands - SDI-12 • 118
ac Sine Wave • 7 Comment • 69
Accuracy • 3, 1, 13 Communication • 11, 18, 31, 131, 154
Address • 16 Communications Ports • 28
Address -- Modbus • 141 Compile Results • 16
Address -- SDI-12 • 112 Configuration • 59
Ampers (Amps) • 1 Connection • 4, 11, 25
Analog • 6, 25, 1 Conserving Code Space • 88
Analog Input Range • 35, 40 Constant • 73, 76, 2
Analog Measurement • 153 Constant -- Predefined • 76
Analog Sensor • 46 Constant Declaration • 93
Analog Sensors • 6, 35 Control • 50, 96
AND Operator • 88 Control Instructions • 8
ANSI • 1, 23 Control Output Expansion • 49
Arithmetic • 87 Control Peripheral • 49
Arithmetic Functions • 102 Control Port • 8
Array • 75, 86, 88, 7 cr • 2
Asynchronous Comunication • 8, 1 CR10X • 105
CR23X • 105
B CR510 • 105
CRBASIC Editor • 70
Background Calibration • 41
CRBASIC Program • 11, 18
Backup Battery • 33
CRBASIC Programming • 69
Battery Backup • 33
Baud • 11, 59, 105, 154
Baud Rate • 105, 108, 1 D
Beacon • 135, 2 Data Acquisition System -- Components • 3
Beginner Software • 11 Data Acquisition System -- Data Retrieval • 4
Binary • 2 Data Acquisition System -- Datalogger • 4
Binary Control • 49 Data Acquisition System -- Sensor • 3, 37
Binary Format • 71 Data Collection • 4, 18
Boolean • 75 Data Format • 132
Bridge • 6, 7, 41 Data Monitoring • 11, 18
Bridge Measurement • 7 Data Point • 3
Budget • 53, 118, 119 Data Retrieval • 131, 132
Data Storage • 30, 81, 94
C Data Storage -- Trigger • 126
Data Table • 11, 77, 80, 90, 94
Cable Length • 46
Data Table Access • 106
Calibration • 33
Data Table Management • 106
Care • 32, 147
Data Table Modifier • 94
Ccontrol I/O • 37, 2
Data Table Name • 73
CE Compliance • 37
Data Type • 75
Charging Circuit • 158, 159, 1
Data Types, NAN, and ±INF • 153
Circuit • 51
Datalogger • 4
Clients • 145
Datalogger Support Software • 34, 3
Clock Accuracy • 37
DC • 3
Clock Function • 104
DC Excitation • 37
Clock Synchronization • 11
DCE • 28, 3, 6

35
Index

Debugging • 151 G
Declaration • 73, 77, 93
Declaration -- Data Table • 94 Gain • 38, 86
Declaration -- Modbus • 140 Garbage • 4
Desiccant • 32, 3 Gas-Discharge Tubes • 55
DevConfig • 59, 3 Generator • 13, 70
Device Configuration • 59 Glossary • 1
Device Map • 138 GOES • 108
Diagnosis -- Power Supply • 156 Ground • 27, 33, 55, 56, 4
Diagnostics • 98
Differential • 3 H
Digital • 3
Half Bridge • 41
Digital I/O • 8, 25, 37, 45, 49, 99
Half Duplex • 5
Dimension • 75
Hello Exchange • 5
Disable Variable • 81, 82, 125, 153
Hello Request • 135
DisableVar • 125, 153
Hello-Message • 135
Documentation • 69
Hertz • 5
DTE • 28, 3, 6
Hexadecimal • 71
Durable Settings • 67
High-Frequency • 44
Humidity • 32
E
Earth Ground • 27, 55, 4 I
Editor • 13
I/O Port • 49
Editor -- Short Cut • 70
ID • 62
Enclosures • 147
IEEE4 • 75, 5
Engineering Units • 4
Infinite • 153
Error • 153
Initiate Telecommunications • 109, 132
Error -- Analog Measurement • 38, 57
Input Channel • 6
Errors • 151
Input Range • 37, 40
ESD • 27, 4, 12
Input/Output Instructions • 5
ESD Protection • 55, 56
Installation • 4
Evapotranspiration • 95
InstrucIntions • 96
Example • 10
Instruction • 84
Example Program • 10, 13
Instruction Times • 98
Excitation • 4
Instructions -- ABS • 102
Execution • 83
Instructions -- ACOS • 101
Execution Interval • 83
Instructions -- Alias • 72, 73, 77, 85, 93
Execution Time • 4
Instructions -- AND • 100
Expression • 86, 87, 4
Instructions -- ASIN • 101
Expression -- Logical • 88
Instructions -- ATN • 101
External Power Supply • 28
Instructions -- ATN2 • 101
Instructions -- Average • 94
F Instructions -- Avgspa • 103
Fill and Stop Memory • 129 Instructions -- Battery • 155, 156
Final Storage • 4 Instructions -- BeginProg ... EndProg • 96
Firmware • 29 Instructions -- Call • 96
Flag • 75, 76, 141 Instructions -- CallTable • 96
Floating Point Arithmetic • 87 Instructions -- ClockSet • 104
Format -- Numerical • 71 Instructions -- Const • 93
Forward • 1 Instructions -- COS • 101
Frequency • 42 Instructions -- CovSpa • 103
Function Codes -- Modbus • 141 Instructions -- DataInterval • 81, 94
Instructions -- DataTable ... EndTable • 94
Instructions -- Delay • 96
Instructions -- Dim • 93, 3

36
 Index

Instructions -- Do ... Loop • 96 Integration • 40

Instructions -- EXP • 102 Intermediate Storage • 5
Instructions -- FieldNames • 94 Interrupt • 8
Instructions -- FIX • 102 Interval • 7
Instructions -- For ... Next • 96 Introduction • 1
Instructions -- FRAC • 102 Inverse Format Registers -- modbus • 142
Instructions -- GetValue • 105
Instructions -- GOESData • 108 L
Instructions -- GOESGPS • 108
Instructions -- GOESSetup • 108 Lead Length • 46
Instructions -- GOESStatus • 108 Leaf Node • 133, 134
Instructions -- IfTime • 104 Lightning • 55, 56, 4
Instructions -- IIF • 100 Lightning Protection • 56
Instructions -- INT • 102 Lightning Rod • 56
Instructions -- LOG • 102 Link Performance • 137
Instructions -- LOG10 • 102 LoggerNet • 144, 145
Instructions -- Maximum • 94 Logical Expression • 88
Instructions -- MaxSpa • 103 Logical Operators • 100
Instructions -- Minimum • 94 Loop Counter • 5
Instructions -- MinSpa • 103 Low-Level ac • 45
Instructions -- MOD • 102
Instructions -- ModBusMaster • 107 M
Instructions -- ModBusSlave • 107
Maintenance • 32, 147
Instructions -- NOT • 100
Manual Organization • 1
Instructions -- OR • 100
Manually Initiated • 5
Instructions -- PeriodAvg • 99
Math • 87, 100, 153
Instructions -- PortGet • 99
Mathematical Operation • 87
Instructions -- PortSet • 99
Measurement -- Accuracy • 46, 55, 1, 13
Instructions -- Public • 93, 8
Measurement -- Instruction • 84, 98
Instructions -- PulseCount • 98
Measurement -- Peripheral • 49
Instructions -- Randomize • 104
Memory • 88, 129
Instructions -- ReadSendGetInfo • 105
Memory Conservation • 88, 130
Instructions -- RealTime • 104
Memory Reset • 130
Instructions -- RectPolar • 102
Milli • 5
Instructions -- RMSSpa • 103
Modbus • 107, 139, 141, 5
Instructions -- RND • 104
Moisture • 32
Instructions -- Sample • 94
Monitoring Data • 11, 18
Instructions -- Scan ... NextScan • 96
Mounting • 4
Instructions -- Select Case ... Case ... Case Is ... Case
Multi-Meter • 6
Else ... EndSelect • 96
mV • 6
Instructions -- SendData • 105
Instructions -- SerialInput • 105
Instructions -- SetStatus • 106 N
Instructions -- SetValue • 105 NAN • 153, 6
Instructions -- SGN • 102 Neighbor Device • 6
Instructions -- SIN • 101 Network • 134
Instructions -- StdDev • 94 Network Planner • 145
Instructions -- StdDevSpa • 103 NIST • 6
Instructions -- TAN • 101 Node • 6
Instructions -- Totalize • 94 Nodes • 133
Instructions -- Units • 93 Noise • 40
Instructions -- While ... Wend • 96 Nominal Power • 29
Instructions -- WindVector • 95 Not-A-Number • 153
Instructions -- XOR • 100 Null-Modem • 3, 6
Instructions Sqr • 102 Numerical Format • 71
Integer • 5

37
Index

O Program • 13, 93
Program -- Alias • 77, 93
Offset • 86 Program -- Array • 103
Ohm • 6 Program -- Constant • 76
Ohms Law • 7 Program -- Data Storage Processing instruction •
On-Line Data Transfer • 7 81
Operating System • 60 Program -- Data Table • 77
Operator • 100 Program -- Data Type • 75, 77
OS • 60 Program -- DataInterval () • 81
OS Date • 16 Program -- Declaration • 77
OS Version • 16 Program -- Dimension • 93
Output • 7 Program -- Documenting • 69
Output Array • 7 Program -- Execution • 83
Overview • 23 Program -- Expression • 86, 153
Overview -- Modbus • 139 Program -- Floating Poing Arithmetic • 75, 87,
Overview -- Power Supply • 53 153
Program -- Instruction • 84
P Program -- Mathematical Operation • 87
Program -- Measurement Instruction • 98
PakBus • 105, 133, 7, 33
Program -- Modbus • 139
PakBus Information • 31, 7
Program -- Multiplier • 86
PakBus Overview • 133
Program -- Offset • 86, 120
Parameter • 7
Program -- Output Processing • 81, 94
Parameter Type • 85
Program -- Parameter Type • 85
PC Program • 13, 69
Program -- Resource Library • 109
PC Support Software • 34, 143
Program -- Scan • 72, 83
PC200W • 11, 143
Program -- Structure • 72
PC400 • 144
Program -- Subroutine • 83
PDA Support • 145
Program -- Task Priority • 83
Peer-To-Peer • 105
Program -- Timing • 83
Period Average • 8
Program -- Unit • 93
Peripheral • 8, 29
Program -- Variable • 93, 11
Peripherals • 29
Program DataTable () • 77
Pin Out • 21
Program Editor • 69
Ping • 137
Programming • 13, 69, 143
PLC • 139, 140, 5
Protection • 27, 32, 147
Polar Sensor • 123
Protocols Supported • 132
Polarity Reversal • 53
Pulse • 7, 8
Port • 8
Pulse Count • 42
Power • 155, 12, 30
Pulse Input • 7
Power Consumption • 53
Pulse Input Channels • 42
Powering Sensor • 37
Pulse Measurement • 42
Precision • 37, 8, 13
Pulse Sensor • 43
Predefined Constant • 76
Primer • 3
Print Device • 8 Q
Print Peripheral • 8 Quickstart Tutorial • 3
Priority • 83
Processing • 100
Processing -- Output • 94
R
Processing -- Spatial • 103 Range Limit • 37
Processing -- Wind Vector • 120 Record Number • 106
Processing Instructions • 8 Recorder • 99, 117, 118
Processing Instructions -- Output • 81 Regulator • 155, 8
Relay • 50, 31
Relay Driver • 31

38
 Index

Relays • 50, 31 Setting • 12, 30

Reliable Power • 53 Setting -- CRBASIC • 66
Requirement -- Power • 53 Setting -- Durable • 67
Reset • 60 Setting -- Terminal Emulator • 66
Resistance • 3, 6, 7, 9 Setting- PakBus • 18, 33
Resistive Bridge • 6, 41 Settings Editor • 133
Resistor • 9 Short Cut • 13, 69
Resolution • 9, 13 SI -- Systeme Internationale • 10
Resolution -- Concept • 13 Signal Conditioner • 32
Resolution -- Data Type • 75 Signatured Packet • 31
Resolution -- Definition • 9 Sine Wave • 7
Retrieving Data • 131, 132 Single-Ended • 45, 57
Ring Memory • 4, 9 Skipped Scan • 151
RMS • 9 Software • 11, 34, 143, 11
Router • 31, 33 Software -- Beginner • 143
RS-232 • 154, 9 Solar Panel • 158, 30
RS-232 Pin Out • 21 Spark Gap • 55
RS-232 Port • 9, 21 Spatial Processing • 103
RTDAQ • 144, 3 Specifications • 37
RTU • 140 Square Wave • 44
Runtime Signature • 10 SRAM • 30
Standard Deviation • 90, 94, 103
S Starter Software • 34, 143
State • 11
Sample Rate • 9 Status • 106
Satellite • 108 status table • 15
SCADA • 107 Storage • 129
Scan • 9 Strain • 41
Scan (Execution Interval) • 9 Structure -- Program • 72
Scan Interval • 72, 9 Subroutine • 83
Scientific Notation • 71 Supply • 155
SDI-12 • 112, 10 Support Software • 143, 3
SDI-12 Measurement • 153 Surge Protection • 34
SDI-12 Recording • 46 SW Battery • 28
SDI-12 Sensor • 47, 112 SW-12 • 50
Self-Calibration • 33, 41 Synchronous • 11
Send • 10 System Clock • 66
Sensor • 3, 29 Systeme Internationale • 10
pulse • 7, 42, 8
Sensor -- Analog • 6
T
Sensor -- Bridge • 6
Sensor -- Frequency • 8, 43 Table • 72, 77
Sensor -- Period Average • 8 Table -- Data Header • 77
Sensor -- Resistive Bridge • 41 Telecommunication • 131
Sensor -- Serial • 28, 47 Temperature Range • 37, 147
Sensor -- Sine Wave • 25 Terminal Emulator • 59, 66
Sensor -- Square Wave • 25, 43 Terminal Emulator Settings • 66
Sensor -- Voltage • 3, 6, 153 Terminal Input Module • 51
Sensor Support • 37, 112 Thermistor • 41, 98
Sequence • 38 Timestamp • 79
Serial • 10 TIMs • 51
Serial I/O • 105 TLL • 11
Serial Input • 105 Tutorial • 3
Serial Sensor • 47 Tutorial Exercise • 10

39
Index

U Voltage Measurement • 27, 38

Volts • 12
UPS • 11
User Program • 30
UTC Offset • 66
W
Watchdog Error • 151, 16
V Watchdog Timer • 12
Weather Tight • 12
Vac • 12 Wind Vector • 120
Variable • 70, 73 Wind Vector Processing • 120
Variable Array • 74 Wiring • 15
Variable Declaration • 73 Wiring Panel • 4
Variable Modifier • 76 Writing Program • 13, 69
Variable Out of Bounds • 151
Vdc • 12
Vector • 120
X
Verify Interval • 135, 136 XOR • 88, 100
Viewing Data • 20
Visual Weather • 143 Z
Volt Meter • 12
Zero • 88

40
 Campbell Scientific Companies

Campbell Scientific, Inc. (CSI)

815 West 1800 North
Logan, Utah 84321
UNITED STATES
www.campbellsci.com • [email protected]

Campbell Scientific Africa Pty. Ltd. (CSAf)

PO Box 2450
Somerset West 7129
SOUTH AFRICA
www.csafrica.co.za • [email protected]

Campbell Scientific Australia Pty. Ltd. (CSA)

PO Box 444
Thuringowa Central
QLD 4812 AUSTRALIA
www.campbellsci.com.au • [email protected]

Campbell Scientific do Brazil Ltda. (CSB)

Rua Luisa Crapsi Orsi, 15 Butantã
CEP: 005543-000 São Paulo SP BRAZIL
www.campbellsci.com.br • [email protected]

Campbell Scientific Canada Corp. (CSC)

11564 - 149th Street NW
Edmonton, Alberta T5M 1W7
CANADA
www.campbellsci.ca • [email protected]

Campbell Scientific Centro Caribe S.A. (CSCC)

300 N Cementerio, Edificio Breller
Santo Domingo, Heredia 40305
COSTA RICA
www.campbellsci.cc • [email protected]

Campbell Scientific Ltd. (CSL)

Campbell Park
80 Hathern Road
Shepshed, Loughborough LE12 9GX
UNITED KINGDOM
www.campbellsci.co.uk • [email protected]

Campbell Scientific Ltd. (France)

3 Avenue de la Division Leclerc
92160 ANTONY
FRANCE
www.campbellsci.fr • [email protected]

Campbell Scientific Spain, S. L.

Avda. Pompeu Fabra 7-9, local 1
08024 Barcelona
SPAIN
www.campbellsci.es • [email protected]

Please visit www.campbellsci.com to obtain contact information for your local US or International representative.