E PSS DS SB 1320 05.03.

2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch

01 Manufacturer's Name & Address : Makes List

02 Manufacturer's Type and Designation : --------------------Double Break----------------------

03 Standard to which equipment conforms : ----------------IS 9921 Part I to V----------------------

04 Rated Voltage KV : ---------------------------110 KV----------------------------

05 Maximum design voltage at which the Isolator can : --------------------------123 KV---------------------------

operate KV

06 Derating factor, if any, for specified test conditions : ----------------------------Unity------------------------------

07 Current rating (Main & Earth Switch)

a) Continuous current A : -------------------------800 Amps-----------------------

b) Dynamic Current KA : ----------------------------78.75 KA--------------------------

c) Three seconds short time current : -------------------31.5 KA for 3.0 Secs--------------

08 Safe duration of over load

a) 150% of rated current : ----------------------------5 Minutes-----------------------

b) 120% of rated current : ----------------------------15 Minutes-----------------------

09 Capacity to interrupt magnetizing current A : ------------------------------7 Amps----------------------

10 Capacity to interrupt line charging current A : ------------------------------6.3 Amps----------------------

11 Maximum Temperature

a) Of current carrying parts when carrying rated : ------------Max. temperatuure 950 C-----------------
continuous current Degree C. --------Temp. 450 C over ambient of 500 C-------

b) Ambient temperature (Maximum / Average for : --------------------------------500 C--------------------------

which (a) is applicable) Degree C

12 Number of Poles : ----------------------------Three--------------------------

E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch

13 Operation

a) Main Switch : --------------------Motor Operated------------------

b) Earth Switch : ---------------------Manual Operated------------------

E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch
14 Number of breaks per circuit per pole

a) Main Switch : ------------Three for Circuit two for Pole-------------

b) Earth Switch : -----------Three for Circuit one for pole--------------

15 Total length of break per pole (min. air distance across : ---------------------------1250 mm-------------------------
the isolating distance) mm.

16 Insulation level

a) Dry one Min. power frequency withstand voltage

i) Across isolating distance : KV rms : -------------------------265 KV rms-----------------------

ii) To earth & between poles : KV rms : -------------------------230 KV rms-----------------------

b) Wet one Min. power frequency withstand voltage

i) Across isolating distance : KV rms : -------------------------265 KV rms-----------------------

ii) To earth & between poles : KV rms : -------------------------230 KV rms-----------------------

c) 1.2/50 micro second impulse withstand voltage

i) Across isolating distance : KV peak : ------------------------630 KV Peak---------------------

ii) To earth & between poles : KV peak : ------------------------550 KV Peak---------------------

17 Earthing Switch

a) Rated current carrying capacity : Amps : -------No rated current but our earth switch
capable to withstood short time current only
18 Switch contacts

a) Type of contacts

i) Fixed contacts : -------------------------Reverseloop-----------------------

ii) Moving contacts : Turn and Twist Turn and twist

Banging type
b) Material

i) Fixed contacts : ---------Hard Drawn Electrolytic Cu. Flat ---------

E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch
ii) Moving contacts : -------- Hard Drawn Electrolytic Cu. Tube -------

c) Area of contacts : Sq.mm : 650 Sq.mm for Main Switch Female Contact
400 Sq.mm for Earth Switch Female Contact
643 Sq. mm for Main Switch Male Contact
463 Sq. mm for Earth Switch Male Contact

d) Whether contacts are silver plated : ---------------------Yes, silver plated--------------------

e) Thickness of silver coating : ---------------------10 to 15 microns--------------------

f) Contact pressure : -------------------- Midium Pressure ------------------

g) No. of operation isolator can make without : ---------------Morethan 1000 operations-------------

deterioration of contacts.
E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch
19 Contact support

i) Material and size of channel : -----------120 x 80 x 3 thick Alu. Extrution-----------

ii) Material and size of plate : ------6 mm thick MS Plate, hot dip galvanized------

20 Clearance:

a) Between live parts and ground : ----------------------------2800 mm-----------------------

b) Between poles : --2400 mm for a phase spacing of 2800 mm--

c) Between live parts and earth : --Equal to dry arcing distance of the insulator--

d) Between live parts when the switch is open

i) On the same pole : --------------------------1800 mm-----------------------

ii) Between adjacent pole : ---------------------------2800 mm-----------------------

21 Bearing

Rotating insulator stool and operating guide

a) i) Location : -----------Below rotating stack insulator------------

ii) Type : ------------------------Ball Bearing-----------------------

iii) Qty. of bearings : -------------2 Nos. / below rotating stack-----------

iv) Size provided : ------------------------- 40 mm dia ----------------------

v) Bearing No. : ---------------------------6208----------------------------

b) Material and size of housing : LM-6, Gravity Die cast sutable for 40 ID Bearing

c) No. of bushes, joints, location & size : -------6 Nos. Tandem pipe clamps 16 ID-------

d) Make of bearing (Reputed makes tenderer to specify): -----------------------SKF or equivalent------------------

22 Operating GI Pipe

i) Tandem Pipe:
E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch

a) Class of GI Pipe : ---------------"B" Class, 32 NB GI Pipe--------------

b) No. of Pipes : 1 Nos. 1 Nos.

c) Wall thickness of GI Pipe : 3.1 mm. 3.1 mm.

E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch
d) Dia of tandem GI Pipe : mm : 32 mm 32 mm

e) Size of Shackle and screw : 16 mm. 16 mm.

f) No. of Clamp and material and size : ------------3 Nos. MS Flat, 8 mm thick-------------

ii) Down Pipe:

a) Class of GI Pipe : ----------------"B" Class, 50 NB GI Pipe-------------

b) Wall thickness : 3.1 mm 3.1 mm

c) Dia of down Pipe : 50 mm Dia 50 mm Dia

iii) Type of joint:

a) Between rotating stool bearing & down pipe : Universal joint. Universal joint

b) Between down pipe & operating mechanism : ----------------------Vernier Flange--------------------

23 Type and Material of isolator terminals : ---------------Rigid Vertical, Aluminium--------------

24 Type and Material of terminal connectors, where : ---------------Confirmed--------------

applicable

25 Type of interlock : Mechanical interlock between Main Switch

and Earth switch

26 Type of switch base : ----------------------Rigid fabricated base--------------

27 Maximum torsional strength Kg.m : --------------------------4 KN M-------------------------

28 Maximum bending strength that will be subjected : ---------------------------4 KN---------------------------

on the post insulator on the opening and closing
of isolator.

29 Rated Mechanical terminal loads

i) Straight Load N Kg : ----------------------------500 N---------------------------

ii) Cross Load N Kg : ----------------------------170 N------------------------

30 Nuts and Bolts

E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch
a) Size, Material and Grade in live parts : M10 and less than M10 are of Stainelss Steel of
AISI 304 Grade.

b) Size, Material and Grade in other parts : ------M12 and above are HDG of grade 4.6-------

c) Whether hot dip galvanised : ------------------Yes, Hot dip galvanised-------------

d) Conforming to IS : ----------IS : 2629, IS : 2633 & IS : 5358----------

31 Insulator base plate

a) Material & size of elevator plate below fixed insulator: --------250x75x5 mm thick MS HDG Plate-----------

b) Material and size of stud and bolts : ----------------------Not Applicable----------------------

E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch
c) Material & size of rotating insulator base plate : -----------10 mm thick MS HDG Plate--------------

32 Phase spacing : ---------------------------2800 mm----------------------

33 Terminal Pad

a) Whether horizontal or vertical : ------------------------Horizontal-----------------------

b) Diameter (mm) : -----------120 x 80 x 3 mm Alu. Extrution-----------

c) Length : ------------------120 x 80 mm Al.--------------------

d) TPI, if threaded : ----------------------Not applicable---------------------

34 Clamp body

a) i) Alloy composition :
---------------Confirmed--------------
ii) Plating if any :

b) Bolts :

35 Indication mechanism for position of switch : ------------------Mechanical Indication-----------------

36 Motor details:

a) Rated voltage : 415 V, Ac supply

c) Type of Motor : Squirrel cage induction motor

d) Frequency : 50 HZ

e) Other details (Tenderers to specify) : 0.5 HP Squirrel cage induction motor

37 Operating time : -----------------------10 to 12 Secs--------------------

38 Torque required to operate the gang operated isolator : ----------------------------36 Kg m-------------------------

39 Control Cabinet:
E PSS DS SB 1320 05.03.2013

ISOLATORS/GROUNDING SWITCHES DATA SHEETS

Sl. No Description 110 KV AB SWITCHES

With Earth Switch Without Earth Switch
a) Materials :

b) Thickness :
---------------------------Not applicable------------------
c) Degree of protection :

d) Whether removable gland plate provided :

40 Switch Design:

a) Rotating/Tilting/Lifting Insulator : Rotating Rotating

b) Horizontal / Vertical Break : Vertical Horizontal

41 Operating mechanism - Reciprocating/Torsional : ------------------------Not applicable--------------------

42 Base:

a) Constructions feature : -----------------Fabricated with Steel-----------------

b) Size of steel section used (mm) : ---------------------125 x 65 x 5 mm--------------------

c) Overall size (mm) : ------------------125 x 255 x 2100 mm----------------

d) Total weight (Kg) : -------------------------70 Kgs approx-------------------

43 Actual dimensions of switch per phase : ------------------250 x 2100 x 4800 mm--------------

44 Weight of the Isolator/pole : -------180 kgs (approx.) without insulators--------

45 Total Weight of one Isolator : -----------540 kgs (approx.) without insulators---------