Patil et al, International Journal of Advanced Engineering Research and Studies E-ISSN2249–8974

Research Paper
OPTIMIZATION OF MIG WELDING PARAMETERS FOR
IMPROVING STRENGTH OF WELDED JOINTS
S. R. Patil1, C. A. Waghmare2

Address for Correspondence

1
M-Tech. Student, 2 Professor, Mechanical Engineering Dept., Rajarambapu Institute of Technology, Sakharale,
Maharashtra, India.
ABSTRACT
This paper presents the influence of welding parameters like welding current, welding voltage, welding speed on ultimate
tensile strength (UTS) of AISI 1030 mild steel material during welding. A plan of experiments based on Taguchi technique
has been used. An Orthogonal array, signal to noise (S/N) ratio and analysis of variance (ANOVA) are employed to study
the welding characteristics of material & optimize the welding parameters. The result computed is in form of contribution
from each parameter, through which optimal parameters are identified for maximum tensile strength. From this study, it is
observed that welding current and welding speed are major parameters which influence on the tensile strength of welded
joint.
KEYWORDS: MIG welding, optimization, orthogonal array, S/N ratio ANOVA.
1. INTRODUCTION effect of each welding parameter on the weld bead
The problem that has faced the manufacturer is the geometry, and then sets out to determine the optimal
control of the process input parameters to obtain a process parameters using the Taguchi method to
good welded joint with the required weld quality. determine the parameters. S.C. Juang and Y.S. Tarng
Traditionally, it has been necessary to study the weld [12] studied the process parameter selection for
input parameters for welded product to obtain a optimizing the weld pool geometry in the tungsten
welded joint with the required quality. To do so, inert gas welding of stainless steel.
requires a time-consuming trial and error EXPERIMENTAL PROCEDURE
development method. Then welds are examined In the present study, in order to identify the process
whether they meet the requirement or not. Finally the parameters with the maximum ultimate tensile
weld parameters can be chosen to produce a welded strength in the GMAW for plan carbon steel, the
joint that closely meets the joint qualities. Also, what Taguchi method was used. Three three-level process
is not achieved or often considered is an optimized parameters, i.e. welding current, voltage and welding
welding parameters combination, since welds can speed were considered. Based on theoretical and
often be formed with very different parameters. In experimental viewpoints, the respective levels are set.
other words, there is often a more ideal welding input The levels of parameters are listed in Table 1. The
parameters combination, which can be used. experimental layout for the parameters, using the L9
In order to overcome this problem, various orthogonal array, is shown in Table 2.
optimization methods can be useful to define the Table 1 Levels of process variables
desired output variables through developing
mathematical models to specify the relationship
between the input parameters and output variables.
Design of experiment (DoE) techniques has been
applied to carry out such optimization. Taguchi
method have been adapted for many applications in
different areas. Table 2 Experimental layout using L9 orthogonal array
2. LITERATURE REVIEW
Sukhomay Pal, Santosh K. Malviya, Surjya K. Pal
and Arun K. Samantaray[1] studied ptimization of
quality characteristics parameters in a pulsed metal
inert gas welding process using grey-based Taguchi
method. K.Y. Benyounis and A.G. Olabi[2] The
optimization methods used in this study are
appropriate for modeling, control and optimizing the
different welding process. A. Kumar and S. In the welding experiments, a carbon steel wire
Sundarrajan[3] Taguchi method was applied to ER70S-6 with a 1.2-mm diameter was used. The
optimize the pulsed TIG welding process parameters work-pieces consisted of AISI 1030 carbon steel with
of AA 5456 Aluminum alloy welds for increasing the a thickness of 10-mm. The chemical composition
mechanical properties. P. Srinivasa Rao, O. P. Gupta, (wt.%) of both base metal and electrode wire are
S. S. N. Murty and A. B. Koteswara Rao[4] studied given in Table 3. The GMAW process was used for
the effect of process parameters and mathematical the welding of a single V-butt joint with a single pass
model for the prediction of bead geometry in pulsed on 100x50 mm plates. Argon (100%) gas was used as
GMA welding. Ching-Been Yang & Chyn-Shu Deng shielding gas at a constant flow rate of 17 L/min.
and Hsiu-Lu Chiang[6] proposes a progressive Table 3 Chemical composition (wt.%) of work material
Taguchi neural network model, which combines the and electrode wire used
Taguchi method with the artificial neural network to
construct a prediction model for a CO2 laser cutting
experiment. Her-Yueh Huang[8] They presents the

Int. J. Adv. Engg. Res. Studies / II/ IV/July-Sept., 2013/14-16

 Patil et al, International Journal of Advanced Engineering Research and Studies E-ISSN2249–8974

3.1 Taguchi’s design method characteristic, a greater S/N ratio relates to better
Taguchi Technique is used to plan the experiments. quality characteristics. Therefore, the optimal level of
The Taguchi method has become a influential tool for the process variables is the level with the greatest S/N
improving output during research and development, ratio. The S/N response table for ultimate tensile
so that better quality products can be produced strength is shown in Table No.5 as below.
quickly and at minimum cost. Dr. Taguchi of Nippon Table 5 S/N Response table for UTS
Telephones and Telegraph Company, Japan has
established a method based on "ORTHOGONAL
ARRAY" experiments which gives much reduced
"variance" for the experiment with "optimum
settings" of control variables. Thus the marriage of
Design of Experiments with optimization of control
Table 6 Results of analysis of variance for UTS
parameters to find best results is attained in the
Taguchi Method. "Orthogonal Arrays" (OA) gives a
set of well balanced (minimum) experiments and Dr.
Taguchi's Signal-to-Noise ratios (S/N), which are log
functions of desired output, serve as objective
functions in optimization, help in data analysis and
estimation of optimum results.
The signal-to-noise (S/N) ratio for each level was From table 5, the optimum levels are A3B3C3 which
based on the S/N ratio analysis. Based on the tensile is based on larger-the-better criterion. The ANOVA
strength of the weld joint (larger-the-better), a higher is a statistical tool used to determine the level of
S/N ratio produced a better quality. The standard S/N contribution of each process parameter to the overall
ratio formula for this type of response is: improvement of the tensile strength of the welded

⁄  10 log
. . .  joint. From the table 6, the welding speed has
Where, M.S.D. is the mean square deviation for the maximum contribution. This has been found to have
output characteristic. the most influence on tensile strength. Thus, a little

1 1
variation in the welding speed is expected to greatly
  10 log     affect the tensile strength of the weld. Hence, the
  more the welding speeds, higher the strength.

Where ‘i’ is the number of a trial; ‘Yij’ is the quality 4. CONCLUSIONS
of the ith trial and jth experiment; ‘n’ is the total In this research study, the mild steel failure problems
number of experiments. encountered by loads were successfully addressed by
3.2 Analysis of Variance (ANOVA) applying the Taguchi Method. A Taguchi orthogonal
The purpose of the analysis of variance (ANOVA) is array, the signal-to-noise (S/N) ratio and analysis of
to examine which design parameters significantly variance (AVOVA) were used for the optimization of
affect the quality characteristic. This is to welding parameters. The optimum levels obtained are
accomplished by separating the total variability of the A3B3C3. It is found that welding speed has major
S/N ratios, which is measured by the sum of the influence on tensile strength of welded joints.
squared deviations from the total mean S/N ratio, into REFERENCES
contributions by each of the parameters and the error. 1. Sukhomay Pal, Santosh K. Malviya, Surjya K. Pal &
Arun K. Samantaray, “Optimization of quality
First, the total sum of squared deviations SST from characteristics parameters in a pulsed metal inert gas
the total mean S/N ratio nm can be calculated as, welding process using grey-based Taguchi method,” Int
  
   
J Adv Manuf Technol (2009)44:1250–1260, DOI
10.1007/s00170-009-1931-0.
3. RESULTS AND DISCUSSION 2. K.Y. Benyounis and A.G. Olabi, “Optimization of
different welding processes using statistical and
In this research work effect of main input welding numerical approaches – A reference guide,” Advances
parameters on the tensile strength of welded joint in in Engineering Software 39 (2008) 483–496.
gas metal arc welding process were investigated. 3. A. Kumar and S. Sundarrajan, “Optimization of pulsed
Table 4 Experimental result for UTS and S/N ratio TIG welding process parameters on mechanical
properties of AA 5456 Aluminum alloy weldments,”
Materials and Design 30 (2009) 1288–1297.
4. P. Srinivasa Rao, O. P. Gupta, S. S. N. Murty and A. B.
Koteswara Rao, “Effect of process parameters and
mathematical model for the prediction of bead
geometry in pulsed GMA welding,” Int J Adv Manuf
Technol (2009) 45:496–505, DOI 10.1007/s00170-009-
1991-1.
5. Saurav Datta, Asish Bandyopadhyay and Pradip Kumar
Pal, “Modeling and optimization of features of bead
geometry including percentage dilution in submerged
arc welding using mixture of fresh flux and fused slag,”
Results show that among main input welding Int J Adv Manuf Technol (2008) 36:1080–1090, DOI
parameters the effect of the welding speed is 10.1007/s00170-006-0917-4.
6. Ching-Been Yang, Chyn-Shu Deng and Hsiu-Lu
significant. Increasing the welding speed and Chiang, “Combining the Taguchi method with artificial
decreasing the current increases the ultimate tensile neural network to construct a prediction model of a
strength of welded joint. In this research work it was CO2 laser cutting experiment,” Int J Adv Manuf
Technol (2012) 59:1103–1111, DOI 10.1007/s00170-
observed that the voltage did not contribute as such to 011-3557-2.
weld strength. Regardless of the set of the quality
Int. J. Adv. Engg. Res. Studies / II/ IV/July-Sept., 2013/14-16
 Patil et al, International Journal of Advanced Engineering Research and Studies E-ISSN2249–8974
7. Ni Xiansheng, Zhou Zhenggan, Wen Xiongwei and Li
Luming, “The use of Taguchi method to optimize the
laser welding of sealing neuro-stimulator,” Optics and
Lasers in Engineering, 49(2011)297–304.
8. Her-Yueh Huang, “Effects of activating flux on the
welded joint characteristics in gas metal arc welding,”
Materials and Design 31 (2010) 2488–2495.
9. Sandip Bhattacharya, Kamal Pal and Surjya K. Pal,
“Multi-sensor based prediction of metal deposition in
pulsed gas metal arc welding using various soft
computing models,” Applied Soft Computing 12 (2012)
498–505.
10. E.M. Anawa and A.G. Olabi, “Using Taguchi method
to optimize welding pool of dissimilar laser-welded
components,” Optics & Laser Technology
40(2008)379–388.
11. Catarina Vidal, Virginia Infante and Pedro Vilaca,
“Assessment of Improvement Techniques Effect on
Fatigue Behaviour of Friction Stir Welded Aerospace
Aluminium Alloys,” Procedia Engineering 2 (2010)
1605–1616.
12. S.C. Juang and Y.S. Tarng, “Process parameter
selection for optimizing the weld pool geometry in the
tungsten inert gas welding of stainless steel,” Journal of
Materials Processing Technology 122 (2002) 33–37.

Int. J. Adv. Engg. Res. Studies / II/ IV/July-Sept., 2013/14-16