iCAM7100 SERIES

HARDWARE GUIDE
A D V A N C E D M U LT I FA C T O R B I O M E T R I C I R I S R E A D E R

VERSION 1.3

iCAM7101
iCAM7111

DUAL FACE CONTACTLESS

4.3 LCD
IRIS CAMERA CARD READER

ISO/ANSI EASY
COMPLIANT INSTALLATION

Fully automatic dual iris capture

Simple non-intrusive, non-contact user interface
Integrated megapixel face camera with flash
ISO/ANSI compliant iris and face images
4.3” color touch screen LCD
Integrated contactless smart card reader [optional]
Surface mount plate included; Recess mounting kit [optional]

Packing List
What’s in the Box
iCAM7100 series
Hardware Guide
L wrench
iCAM7100 SERIES

Required Equipment (not included) HARDWARE GUIDE

A D V A N C E D M U LT I FA C T O R B I O M E T R I C I R I S R E A D E R

VERSION 1.2

Power Source
12-24 VDC +/- 10% / Minimum 24W (12VDC @ 2AMPS) DUAL
IRIS
FACE
CAMERA
4.3 LCD
iCAM7101

CONTACTLESS
CARD READER
iCAM7111

(Measured at iCAM unit) ISO/ANSI

COMPLIANT

Fully automatic dual iris capture

Simple non-intrusive, non-contact user interface
EASY
INSTALLATION

Integrated megapixel face camera with flash

Uninterruptable Power Supply (strongly recommended) ISO/ANSI compliant iris and face images
4.3” Color LCD touch screen available with iCAM7100 models
Integrated contactless smart card reader [optional]
Surface mount plate included; Recess mounting kit [optional]

Packing List

Network What’s in the Box

iCAM7100 series
Hardware Guide
L wrench

Required Equipment (not included)

iCAM7000 SERIES
HARDWARE GUIDE
ADVANCED IRIS RECOGNITION & FACE CAPTURE SYSTEM

VERSION 1.0

Power Source

Ethernet Wiring CAT5e Ethernet Cabling (or better)

12-24 VDC +/- 10% / Minimum 24W (12VDC @ 2AMPS) DUAL
IRIS
FACE
CAMERA
CONTACTLESS
CARD READER
EYE
SAFETY

(Measured at iCAM unit) ISO/ANSI

COMPLIANT
EASY
INSTALLATION

Fully automatic fast dual iris capture

Easy non-intrusive user interface
Wide graphical user interface with 4.3” LCD [optional]
TUV CE

Uninterruptable Power Supply (strongly recommended)

Intergrated high resolution face capture camera
ISO/ANSI compliant face images
Integrated contactless smart card reader [optional]
Seamless integration with conventional security systems
Easy installation with Gang box, Cradles, Recess mounting kit

Packing List

Network
What’s in the Box
iCAM7000 series
Hardware Guide
L wrench
iCAM7000 SERIES
HARDWARE
ADVANCED GUIDE
Required Equipment (not included) VERSION 1.0IRIS RECOGNITION & FACE CAPTURE SYSTEM
Power Source
DUAL
FACE EYE
CONTACTLESS

Ethernet Wiring CAT5e Ethernet Cabling (or better)

12-24 VDC +/- 10% / Minimum 24W (12VDC @ 2AMPS) CAMERA
IRIS4.3
LCD
CARD SAFETY
EASY
ISO/ANSI READER
TUV
INSTALLATION
COMPLIANT CE
(Measured at iCAM unit) Fully
Easy
Wide automatic
non-intrusive
graphical
Intergrated fast
highuser dual
user irisface
interface
resolution capture
interface
with 4.3” LCD
capture [optional]
camera
ISO/ANSI
Integrated
Seamless
Easy compliant
integration
installation withface
contactless withimages
smart
Gang card reader
conventional
box, Cradles, [optional]
security systems kit
Recess mounting
Uninterruptable Power Supply (strongly recommended)
Network
Ethernet Wiring CAT5e Ethernet Cabling (or better)
Ethernet Switch
Software iCAM7000 series Hardware Guide L wrench

Ethernet Switch
Required Software for desired system type
(IrisAccess EAC, iData SDK, etc.)

Software
iCAM7100 series Hardware Guide L wrench

Ethernet Switch
Required Software for desired system type
(IrisAccess EAC, iData SDK, etc.)

Software
Required Software for desired system type iCAM7100 series Hardware Guide L wrench
(IrisAccess EAC, iData SDK, etc.)
Hardware Information

Camera Unit Front View

Up / Down Tilt Buttons
Alignment Guide
Mirror
Face Camera Face Camera Flash

CCTV Camera (optional) Proximity Sensor

MIC / Screw Cap
USB Connector / Screw CAP

Function Buttons Function Buttons

Speaker 4.3” Color Touch Screen LCD

Smart Card Reader (optional)

Status LED Interface Panel

Bottom View

Cable Channel

Tripod Socket Knock-out

(1/4-20 (1/4 diameter, 20 threads per inch))

Rear View

Desktop Stand Hole

Surface Mounting Tamper Switch

Screw Hole

Gang Box Screw Hole

Installation Plate
2
Hardware Information

Inside

Installation Plate Screw

RTC Battery
Factory Default Button
Tamper
Switch
Wiring Legend
Guide

ON
Extra Fuse

OFF
Input / Output Fuse Power LED
Connections On/Off Switch
Power Connection
Ethernet Connection

Wiring Legend Guide Rear View

Extra Fuse

3
Installation Guidelines
1. Recommended Mounting Information
Bottom of 7.01” 2.52”
Mirror (178mm) (64mm)

61” 8.31”
(155cm) (211mm)
54.3”
(138cm)
NOTE
This is based
on the assumption
that users’ average
height is 5‘7”(170cm)
Floor

The recommended mounting height for the iCAM7100 series is 138cm (54.3inches) from the
floor to the bottom of the unit. This mounting height can be adjusted to accommodate the
height of the average user at the installed location.
High amounts of ambient light must be avoided. Intense light sources such as sunlight or
halogen lamps may reduce the image capture performance of the iCAM which may result in
an increased “failure to acquire” rate.
The iCAM was designed for indoor use only. This device is not weatherproof and must not be
exposed to precipitation or extreme temperatures. If it is required to use this product in an
outdoor or extreme environment, a 3rd Party enclosure may be used to protect the unit from
exposure to dust, moisture, and extreme temperatures. See www.irisid.com - Support &
Service for more information. Installation in a extreme environment without proper protection
may cause permanent damage and void your warranty.

2. General Wiring Requirements

The iCAM7100 series requires at least the following wires:
Ethernet network wiring to connect with the network switch for communication.
NOTE For systems consisting of only the iCAM and a computer, an Ethernet cross-over cable
may be used.
IMPORTANT: IT IS RECOMMENDED THAT THE IRISACCESS SYSTEM BE PLACED ON A PRIVATE NETWORK
SEPARATE FROM GENERAL CORPORATE OR PUBLIC ACCESS. SYSTEM PERFORMANCE AND STABILITY MAY BE
AFFECTED DEPENDING ON AMOUNT OF GENERAL NETWORK TRAFFIC.

Power Wiring: The minimum recommended wire gauge used for power is 16AWG (1.0mm 2 )
Power Requirements: 12-24VDC +/- 10% / Minimum 24W (12VDC @ 2AMPS)
NOTE Use of a stable power supply and proper guage wire is required. Wire length voltage
drop must be accounted for in order to maintain the correct power at the iCAM unit (with
iCAM connected). For example; with a 12VDC source and 16AWG (1.0mm 2 ) copper wire, the
maximum distance is 71.5 Feet (21 Meters). If a longer power wire distance is required, it is
recommended that a 24VDC power source be used. Voltages within the range of 12VDC and
24VDC are acceptable as long as 24W of power is supplied to each iCAM.
(e.g. 12VDC @ 2AMPS = 24Watts OR 24VDC @ 1AMP = 24Watts).
IMPORTANT: IT IS RECOMMENDED TO SUPPLY THE CORRECT AMOUNT OF POWER TO THIS UNIT. AN OVER OR
UNDER VOLTAGE APPLIED TO THIS PRODUCT MAY CAUSE PERMANENT DAMAGE AND VOID THE WARRANTY.

4
iCAM Installation
iCAM7100 Mounting & Stand Solutions
The iCAM7100 series unit can be fitted to a surface mount (available out-of-the-box), recess mount
(with optional recess mounting kit), or optional desktop stand.

Surface Mounting
The iCAM can be surface mounted with standard equipment provided with the contents of your unit.
Review the following procedure for instruction on how to surface mount your iCAM7100 series unit.

1 Open each cap at both sides of unit,

and loosen the captive screws (with included L wrench)
to release the interface panel.
(Left : MIC / Screw Cap.
Right : USB Connector / Screw Cap)

2 After opening the interface panel, loosen the screw.

Unscrew the installation plate screw to seperate from the installation plate.

3 Seperate the installation plate

by sliding the plate downward. Cover Rear

Installation Plate

5
 4 Place the installation plate on the desired wall and screw into wall.
Feed any needed wiring through the installation plate hole (i.e.: Power, Ethernet, etc).
Attach the installation plate to the wall surface using the appropriate fastener (recommended
#10 screws) and anchors for the wall material. Another option is to mount and fasten the
installation plate to a previously installed electrical gang box.

Surface Mount

Hole Marking

Installation Plate

OR

Gang Box Mount

Installation Plate

5 Slide the iCAM7100 series

into the installation plate
and fasten the installation
plate with a screw.

6
6 Remove protective film from RTC battery.

ON
OFF
ON
ON
OFF

OFF
Ethernet Power Supply
Cable Connector

Remove the coin Power on

battery protect film

ON
OFF
7 Before wiring unit, confirm the power
is in the off position. Route and connect
the Power and Ethernet wires to
iCAM7100 series.
NOTE If connecting any other wiring such as Wiegand, GPI/O to the iCAM, review the following
section “Wire Connection Details” before closing interface panel and fastening screws.

8 Turn on power source and switch the power switch of the iCAM7100 series
unit to the ON position.

9 After wiring the unit and switching

it to the ON position, close the interface panel
and fasten the screws.
(with screw caps placed back into closed position).

7
Wire Connection Details

A B C

D E F

A Relay Output

IMPORTANT: ONLY KNOWLEDGEABLE PROFESSIONAL INSTALLERS SHOULD BE USED TO INSTALL ALL

ELECTRONIC ENTRY/EXIT LOCKING DEVICES. DIRECT CONNECTION OF ELECTRONIC ENTRY/EXIT LOCKING
DEVICES SHOULDN’T BE MADE FROM THE RELAY OUTPUTS ON THE ICAM. IT IS THE RESPONSIBILITY OF THE
INSTALLER TO ASSURE THAT THE INSTALLATION IS PERFORMED IN ACCORDANCE WITH ALL COUNTRY/STATE/
LOCAL FIRE AND SAFETY REGULATIONS AND THAT ANY 3RD PARTY PRODUCTS USED WILL NOT CREATE A
HAZARD.

Two independent dry contact relays. The purpose and the duration of the relays are defined
by the controlling software. Typically, Relay_1 (NC_1, COM_1, NO_1) is triggered upon user
acceptance (access granted). The diagram shows Relay_1 connected to indicators which
changes from Red to Green for an accepted user. Relay_2 (NC_2, COM_2, NO_2) is typically
used to indicate iCAM tamper. In this diagram the relay is activated when the iCAM tamper
switch is triggered. The maximum electrical rating for the relay is 3A at 24VDC.
COM_1

COM_2
NO_1

NO_2
NC_1

NC_2

Relay Output
ALARM
LIGHT SYSTEM
POWER 24 HOUR
SUPPLY ZONE
RED GREEN

8
B Wiegand Input
8JFHBOE
JOQVU
JT
BWBJMBCMF
PO
UIF
J$".
GPS
DPOOFDUJPO
GSPN
SE
QBSUZ
QSPYJNJUZ
DBSE
SFBEFST

5IJT
DPOOFDUJPO
DBO
QSPWJEF
7%$
BOE
B
NBYJNVN
N"
DVSSFOU
UP
B
QSPYJNJUZ
DBSE
SFBEFS

DATA_0

DATA_1
12VDC

GND
Wiegand Intput
External
Prox Card 12VDC
Reader DATA_0
DATA_1
GROUND

C Wiegand Output
5IF
8JFHBOE
0VUQVU
GSPN
UIF
J$".
TFSJFT
DBNFSB
VOJU
DBO
CF
VTFE
XJUI
SE
QBSUZ

EFWJDFT
DBQBCMF
PG
SFDFJWJOH
8JFHBOE
EBUB
5IJT
8JFHBOE
PVUQVU
FNVMBUFT
B
UZQJDBM
"DDFTT

$POUSPM
$BSE
3FBEFS
$POGJHVSBUJPO
PG
UIJT
PVUQVU
JT
QSPWJEFE
UISPVHI
TPGUXBSF


4FF
UIF
BTTPDJBUFE
JNBHF
GPS
HFOFSBM
XJSJOH
PG
8JFHBOE
0VUQVU
UP
BO
"DDFTT
$POUSPM
1BOFM
8JFHBOE
4QFDJGJDBUJPOT


o
8JFHBOE
PVUQVU
VTFT

XJSF
JOUFSGBDF
%BUB
%BUB
BOE
(SPVOE


o
.BYJNVN
XJSF
MFOHUI
GSPN
J$".
UP
"DDFTT
$POUSPM
1BOFM
JT
GFFU
N

DATA_0

DATA_1

GND
NC

Wiegand Output Card Reader

Interface
GROUND ACCESS
DATA_1 CONTROL
DATA_0 PANEL

D External GPIO
(1*0
BOE

DBO
CF
VTFE
UP
DPOUSPM
UIF
UJMU
QPTJUJPO
PG
UIF
UJMU
VOJU
PG
BO
J$".

6TF
(1*0
BOE
(/%
GPS
VQ
UJMUJOH
6TF
(1*0
BOE
(/%
GPS
EPXO
UJMUJOH
GPIO Specifications:
o
'PS
PVUQVU
UIF
(1*0
DBO
QSPWJEF
7%$
!
N"
o
'PS
*OQVU
UIF
(1*0
JT
TFMFDUBCMF
CFUXFFO
BDUJWF
)JHI

BDUJWF
-PX
o
"TTJHONFOU
PG
(1*0
JT
IBOEMFE
UISPVHI
4PGUXBSF

GPIO3
Up
GROUND
External Tilt GPIO4
GROUND
Down

External GPIO
GPIO1

GND

GPIO2

GND

GPIO3

GND

GPIO4

GND

9
 E RS422 Output
RS422 serial communication port for connection with an access panel or to other computer
equipment. When configured, the Card ID associated with the user is output from the
RS422 output port upon a successful identification.

RXD_P
RXD_N To RS422 port
TXD_P of computer
TXD_N or access system

RS422
Output
RXD_P

RXD_N

TXD_P

TXD_N

F External Smart Card Interface RS232 Smart Card

Allows connection of internally (ex. HID OEM150) and externally installed smart card readers
which utilize serial (RS232) communications. This connection can provide 12VDC and a
maximum of 500mA current to a smart card reader.

External Smart Card Interface

RS232 Smart Card
External
Smart Card
12VDC

TXD

RXD

GND

Reader

10
 G External Speaker Out
Allows for connection of an external amplified speaker. This port provides mono (single
channel) audio of voice prompts and other unit sounds. Both the internal and external
speakers can operate concurrently.

Ground

Signal To amplified speaker

3.5mm

iCAM Configuration

iCAM7100 Series camera contains an internal configuration interface called iCAM Configuration.
This camera specific interface allows installers to perform configuration and setup options to the
iCAM series unit.

How to access the iCAM Configuration interface

From a PC with an internet browser connected to the network (that the iCAM7100 series unit
is connected to), type the IP address of the iCAM. For example, if the IP address of an iCAM is
192.168.5.100 (default IP), you would access the configuration web interface by typing
http://192.168.5.100 from an internet browser.

To login, the User ID required when prompted is iCAM7000. The Password is iris7000.
The system is case sensitive when entering in your login credentials.

Once you have connected to the iCAM Configuration Interface - settings, information, and
options become available to further configure your system. Additional documentation for
setup and configuration can be found at:

http://irisid.com/ss/documentation.htm

11
 How to Operate

12~14”
(31-35cm)

Tilt down -25 Degrees

Read distance 14inches away

Tilt up +35 Degrees

Read distance 14inches

The on-unit up/down tilt buttons can be used to adjust

the tilt angle; or an external mounted switch can be
wired to control up/down tilt via GPI.

o

J$".
BDUJWBUFT
XIFO
VTFS
BQQSPBDIFT
PS
XIFO
DBSE
JT
QSFTFOUFE o

0SBOHF




UVSOT
UP
HSFFO




XIFO
VTFS
JT
BU
DPSSFDU
EJTUBODF
o

1JDUVSF
DBQUVSF
SBOHF
JT
_
JODIFT
DN

BXBZ o

7JTVBM
JOEJDBUJPO
JT
BNQMJGJFE
XJUI
GSJFOEMZ
BVEJP
QSPNQUT
o

4FMG
PS
BVUPTFU
IFJHIU
BEKVTUNFOU o

3JHIU
BOE
MFGU
JSJEFT
BSF
BDRVJSFE
o

1MBDJOH
EPU
PWFS
UIF
CSJEHF
PG
OPTF
FBTJMZ
IFMQT
BMJHONFOU o

"
GBDF
QJDUVSF
DBO
BMTP
CF
DBQUVSFE

Green dot = In range Orange dot = Out of range

12
Restoring The Unit to Factory Default

Factory Default Button

5IF
'BDUPSZ
%FGBVMU
#VUUPO
DBO
CF
VTFE
UP
SFTUPSF
TFUUJOHT

PG
BO
J$".
TFSJFT
DBNFSB
UP
SFTUPSF
TFUUJOHT
UP

GBDUPSZ
EFGBVMU


5IJT
CVUUPO
JT
MPDBUFE
JOTJEF
PG
UIF
VOJU
CFMPX
UIF
35$

CBUUFSZ
TFF
JNBHF

BOE
DBO
CF
VTFE
JO
UXP
EJGGFSFOU
XBZT

1. IP ADDRESS DEFAULT - Resets the IP Address to Factory Default

NOTE Default IP Address = 192.168.5.100, Subnet Mask = 255.255.255.0.

o
)PME
UIF
GBDUPSZ
EFGBVMU
CVUUPO
EPXO
GPS
BU
MFBTU

TFDPOET
XIJMF
UIF
VOJU
JT
BMSFBEZ
QPXFSFEPO

UP
SFTFU
UIF
VOJU
*1
BEESFTT
JOGPSNBUJPO
CBDL
UP
UIF
EFGBVMU
TFUUJOHT

2. FACTORY DEFAULT - Resets All Settings to Factory Default

NOTE "OZ
JOGPSNBUJPO
VQMPBEFE
JOGPSNBUJPO
JODMVEJOH
GJSNXBSF
VQEBUFT

UP
UIF
VOJU
UIBU

NBZ
IBWF
CFFO
QFSGPSNFE
QSJPS
UP
UIJT
SFTFU
GVODUJPO
NBZ
CF
DMFBSFE

"MM
TFUUJOHT
XJMM
CF

GBDUPSZ
SFTUPSFE
UP
UIF
EFGBVMU
MFWFM

o
8IJMF
QPXFSJOH
PO
UIF
J$".
TFSJFT
VOJU
IPME
UIF
GBDUPSZ
EFGBVMU
CVUUPO
EPXO
GPS

BU
MFBTU

TFDPOET
UP
SFTUPSF
UIF
FOUJSF
VOJU
CBDL
UP
BMM
GBDUPSZ
EFGBVMU
TFUUJOHT

13
Fuse Replacement
The iCAM7100 series camera unit(s) contains a replaceable fuse which protects the unit(s)
from excessive current consumption. In the event that the iCAM7100 series unit(s) will not
power on, a fuse replacement may be necessary.

CAUTION: FUSE REPLACEMENT SHOULD BE PERFORMED WITHOUT POWER CONNECTED TO THE UNIT.

TIP The fuse can be tested by checking the continuity across both sides of fuse with
a multi-meter. If no continuity is measured, the fuse must be replaced.
NOTE An additional replacement fuse is included on the back of the Wiring Legend Guide.

How to Replace the Fuse

1 Remove the screws to release the Wiring Legend Guide.

2 Use tweezers, and replace the Fuse.

Fuse Specification
Manufacturer Littlefuse
Part No. 0451 004. MRL
Ampere Rating 4A

14
Memo

Serial Number:

Unit IP Address:

Installation Date:

Note:

15
General Information

The iCAM7100 series contains an optical system designed to operate with the integrated high-
speed multi-sensor iris imager array. The iCAM7100 series will automatically process and outputs
high quality ISO standards compliant iris images of a subject in less than one second.

Dimension (W x H x D) 7.01” x 8.31” x 2.52” (178mm x 211mm x 64mm)

Weight 3.5lbs (1.6kg)
Power Input / Consumtion 12-24VDC, 2.0 Amps @ 12VDC / 24W
Status LED Multi Color - Red, Green, Blue for status and alarm indication
Iris Operating Range Indicator Dual Color - Orange (out of range), Green (in range)
Voice Indication English standard, other available by download
Iris Capture Range 12”~14” (31cm ~ 35cm)
User Input Function keys six user definable
Touch Screen LCD 4.3” diagonal (480 x 272 pixels)
Pin Pad Pop-up on screen pin pad
Flash High output flash for face capture
Face Image Camera Face camera CMOS - 5MP
Relays x 2 Control for user defined operations
External Media Device Connectivity Secure user accessible USB port
Operating Temperature 32°F~113°F (0°C~45°C)
Storage Temperature -4°F~203°F (-20°C~95°C)
Humidity Up to 90% non-condensing
Iris & Face Camera Rotation Angle +35°/-25°
Communications Ethernet (LAN, WAN), RS422, RS232

Inputs / Outputs Proximity Card Reader (Wiegand In), Embedded Smart Card Reader (Optional),
Wiegand In, Wiegand Out, Dry Contact Relay x 2, Programmable GPIO x 4

Equipment Supplied with iCAM7100 Instruction Manual - Hardware Guide

IrisAccess EAC, iData SDK Refer to IrisAccess Control Software specifications

Technical Support

Additional information and technical assistance is available on the Iris ID Systems

support web site at www.irisid.com. Click on Support & Service then Technical Support.

formerly

Iris ID Systems, Inc.

7 Clarke Drive, Cranbury, NJ 08512, USA
Tel. 609-819-IRIS(4747) Fax. 609-819-4736
www.irisid.com
©2011 Iris ID, Inc. All rights reserved. Design and specification subject to change without notice. Printed in Korea