Scribd
Upload
257 views3 pages

Periodical Exam

This document provides information about tools and equipment used in information and communications technology (ICT). It includes a matching exercise that pairs tools with their names and functions. Multiple choice questions test knowledge of specific tools and their purposes. Statements about tool maintenance are identified as true or false. Decimal numbers are also provided to be converted to binary.

Uploaded by

REMAR EMPIMO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
257 views3 pages

Periodical Exam

This document provides information about tools and equipment used in information and communications technology (ICT). It includes a matching exercise that pairs tools with their names and functions. Multiple choice questions test knowledge of specific tools and their purposes. Statements about tool maintenance are identified as true or false. Decimal numbers are also provided to be converted to binary.

Uploaded by

REMAR EMPIMO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

FIRST GRADING IN ICT

I. Match column A to column B. Choose the letter of the correct answer.


A B
1. Torx screwdriver a.

2. Needle-nose plier b.

3. Flat head screwdriver c.

4. Anti-static wrist strap d

5. Tweezers e

6. Part retriever f.

7. Wire cutter g.

8. Anti-static mat h.

9. Flashlight i.

10. Multimeter j.

11. Cable ties k.

12. Compressed air l.

13. Lint-free cloth m.

14. Parts organizer n.

15. Loopback Adapter o.


II. Choose the letter of the correct answer.

1. Which tool is used to blow away dust and debris from different computer parts without touching the
components?
a. Anti-static mat c. Compressed air
b. Hex driver d. Wire cutter
2. Which tool is used to loosen or tighten slotted screws?
a. Part Retriever c. Cable ties
b. Lint-free Cloth d. Flat head screwdriver
3. Which tool is used to strip and cut wires?
a. Anti-static mat c. Philips head screwdriver
b. Hex driver d. Wire cutter
4. Which tool is used for hardware to stand on to prevent static electricity from building up?
a. Anti-static mat c. Philips head screwdriver
b. Hex driver d. Wire cutter
5. Which tool is used to loosen or tighten cross-head screws?
a. Anti-static mat c. Philips head screwdriver
b. Hex driver d. Wire cutter
6. Which tool is sometimes called a nut driver? It is used to tighten nuts in the same way that a screwdriver
tightens screws?
a. Anti-static mat c. Philips head screwdriver
b. Hex driver d. Wire cutter
7. Which tool is used to loosen or tighten screws that have a star-like depression on the top, a feature that is
mainly found on laptop?
a. Anti-static mat c. Philips head screwdriver
b. Torx screwdriver d. Wire cutter
8. Which tool is used to retrieve parts from location that are too small for your hand to fit?
a. Part Retriever c. Cable ties
b. Lint-free Cloth d. Flat head screwdriver
9. Which tool is used to clean different computer components without scratching or leaving debris?
a. Part Retriever c. Cable ties
b. Lint-free Cloth d. Flat head screwdriver
10. Which tool is used to bundle cables neatly inside and outside of a computer?
a. Part Retriever c. Cable ties
b. Lint-free Cloth d. Flat head screwdriver
11. Early drive controller interface that connects computers and hard disk drives which an interface that uses a 40pin
connector.
a. Optical drive b. Memory module c. IDE d. Registers
12. Soldered the memory chips on a special circuit board.
a. Memory module b. IDE c. Optical d. DDR
13. A removable storage device that connects to a USB port.
a. Floppy Drive b. Hard Drive c. Flash Drive d. Optical Drive
14. Technology that doubles the maximum bandwidth of SDRAM.
a. Memory module b. IDE c. DDR d. Optical

15. A storage device that uses lasers to read data on the optical media.
a. Optical Drive b. Hard Drive c. Flash Drive d. CD
16. A magnetic storage device that is installed inside the computer.
a. Hard Drive b. Flash Drive c. RAM d. ROM
17. A storage device that uses removable 3.5-inch disks.
a. Flash Drive b. Floppy Drive c. Hard Drive d. RAM
18. Temporary storage for data and programs that are being accessed by the CPU.
a. ROM b. RAM c. Drive d. CD
19. Memory cells built right into the CPU that contain specific data needed particularly the Arithmetic and Logic Unit.
a. Registers b. Memory module c. IDE d. Optical drive
20. Chips that are located on the motherboard.
a. ROM b. RAM c. Drive d. CD

III. Write T if the statement is true and F if the statement is false.


1. All tools and equipment must be properly maintained so that workers are not endangered.
2. Preventive maintenance is the systematic care and protection of tools, equipment and machines in order
to keep them in a safe, usable condition, limit downtime and extend productivity.
3. The degree of detail to include regarding tools and equipment maintenance will depend on the kinds of
tools/equipment used.
4. Damaged or defective equipment/tools should be tagged and removed from service.
5. The safe use of a tool depends on using the tool for the purpose for which it was designed and also for other
purposes where it can be used as substitute where tool is not available.
6. Most manufacturers can provide maintenance schedules for their equipment.
7. Properly stored tools and equipment will be easy to find when needed and are less likely to be lost.
8. Preparing for a task includes also the sequence of tasks to be done.
9. Use bins for storing small parts is a good practice on proper storage.
10. Productivity is increased because time is not lost looking for tools, parts and equipment is one of the
benefits of proper storage.

IV. Direction: Convert the decimal numbers shown below to binary. Perform checking to verify
answers. (3 pts each)

1. 21
2. 43

You might also like