Engineering interview questions,Mcqs,Objective Questions,Class

Notes,Seminor topics,Lab Viva Pdf free download. CIVIL | Mechanical | CSE |

EEE | ECE | IT | Chemical Online Quiz Tests for Freshers.

HOME Interview Questions MCQs *LAB VIVA CLASS NOTES SEMINAR TOPICS
ONLINE TEST GD TOPICS GATE CAT

Home » Circuits & Circuit Theory Questions » 300+ TOP A.C.

Fundamentals, Circuits & Circuit Theory Multiple Choice
Questions and Answers

300+ TOP A.C. Fundamentals,

Circuits & Circuit Theory
Multiple Choice Questions and
Answers
 Engineering
Questions
Engineering
5,665 likes

Like Page

Be the first of your friends t

A.C. Fundamentals, Circuits and Circuit Theory

Questions :-
1. A sine wave has a frequency of 50 Hz. Its angular
Hotels in El
frequency is _______ radian/second.
(a) 100 n
(b) 50 jt
(c) 25 JT
(d) 5 n
Ans: a

2. The reactance offered by a capacitor to alternating

current of frequency 50 Hz is 20 Q. If frequency is increased
to 100 Hz, reactance becomes_____ohms.
(a) 2.5
(b) 5
(c) 10
(d) 15
Ans: c

3. The period of a wave is

(a) the same as frequency
(6) time required to complete one cycle
(c) expressed in amperes
(d) none of the above
Ans: b
4. The form factor is the ratio of
(a) peak value to r.m.s. value
(6) r.m.s. value to average value
(c) average value to r.m.s. value
(d) none of the above
Ans: b

5. The period of a sine wave is _____ seconds.

Its frequency is
(a) 20 Hz
(b) 30 Hz
(c) 40 Hz
(d) 50 Hz
Ans: d

6. A heater is rated as 230 V, 10 kW, A.C. The value 230 V

refers to
(a) average voltage
(b) r.m.s. voltage
(c) peak voltage
(d) none of the above
Ans: b

7. If two sinusoids of the same frequency but of different

amplitudes and phase angles are subtracted, the resultant is
(a) a sinusoid of the same frequency
(b) a sinusoid of half the original frequency
(c) a sinusoid of double the frequency
(d) not a sinusoid
Ans: a

8. The peak value of a sine wave is 200 V. Its average value is

(a) 127.4 V
(b) 141.4 V
(c) 282.8 V
(d)200V
Ans: a
9. If two sine waves of the same frequency have a phase
difference of JT radians, then
(a) both will reach their minimum values at the same instant
(b) both will reach their maximum values at the same instant
(c) when one wave reaches its maxi¬mum value, the other will
reach its minimum value
(d) none of the above
Ans: c

10. The voltage of domestic supply is 220V. This figure

represents
(a) mean value
(b) r.m.s. value
(c) peak value
(d) average value
Ans: a

11. Two waves of the same frequency have opposite phase

when the phase angle between them is
(a) 360°
(b) 180°
(c) 90°
(d) 0°
Ans: b

12. The power consumed in a circuit element will be least

when the phase difference between the current and voltage
is
(a) 180″
(b) 90°
(c) 60°
(d) 0°
Ans: b

13. The r.m.s. value and mean value is the same in the case
of
(a) triangular wave
(6) sine wave
(c) square wave
(d) half wave rectified sine wave
Ans: c

14. For the same peak value which of the following wave will
‘have the highest r.m.s. value ?
(a) square wave
(b) half wave rectified sine wave
(c) triangular wave
(d) sine wave
Ans: a

15. For the same peak value, which of the following wave has
the least mean value ?
(a) half wave rectified sine wave
(b) triangular wave
(c) sine wave
(d) square wave
Ans: a

16. For a sine wave with peak value Imax the r.m.s. value is
(a) 0.5 Imax
(b) 0.707
(c) 0.9
(d) 1.414 Lmax
Ans: b

17. Form Factor is the ratio of

(a) average value/r.m.s. value
(b) average value/peak value
(e) r.m.s. value/average value
(d) r.m.s. value/peak value
Ans: c

18. Form factor for a sine wave is

(a) 1.414
(b) 0.707
(c) 1.11
(d) 0.637
Ans: c

19. For a sine wave with peak value Emax______8.30. the

average value is
(a) 0.636 Emax
(b) 0.707 Emax
(c) 0.434 EWc
(d) lAUEmax
Ans: a

20. For a frequency of 200 Hz, the time period will be

(a) 0.05 s
(b) 0.005 s
(c) 0.0005 s
(d) 0.5 s
Ans: b

21. The phase difference between voltage and current wave

through a circuit element is given as 30°. The essential condition
is that
(a) both waves must have same frequency
(b) both waves must have identical peak values
(c) both waves must have zero value at the same time
(d) none of the above
Ans: a

22. The r.m.s. value of a sinusoidal A.C. current is equal to its

value at an angle of______degrees.
(a) 90
(b) 60
(c) 45
(d) 30
Ans: c

23. Capacitive reactance is more when

(a) capacitance is less and frequency of supply is less
(b) capacitance is less and frequency of supply is more
(c) capacitance is more and frequency of supply is less
(d) capacitance is more and frequency of supply is more
Ans: a

24. In a series resonant circuit, the impedance of the circuit is

(a) minimum
(b) maximum
(c) zero
(d) none of the above
Ans: a

25. Power factor of an electrical circuit is equal to

(a) R/Z
(b) cosine of phase angle difference be-tween current and
voltage
(c) kW/kVA
(d) ratio of useful current to total cur¬rent Iw/I
(e) all above
Ans: e

26. The best place to install a capacitor is

(a) very near to inductive load
(b) across the terminals of the inductive load
(c) far away from the inductive load
(d) any where
Ans: b

27. Poor power factor

(a) reduces load handling capability of electrical system
(b) results in more power losses in the electrical system
(c) overloads alternators, transformers and distribution lines
(d) results in more voltage drop in the line
(e) results in all above
Ans: e

28. Capacitors for power factor correction are rated in

(a) kW
(b) kVA
(c) kV
(d) kVAR
Ans: d

29. In series resonant circuit, increasing inductance to its twice

value and reducing capacitance to its half value
(a) will change the maximum value of current at resonance
(6) will change the resonance frequency
(c) will change the impedance at resonance frequency
(d) will increase the selectivity of the circuit
Ans: d

30. Pure inductive circuit

(a) consumes some power on average
(b) does not take power at all from a line
(c) takes power from the line during some part of the cycle and
then returns back to it during other part of the cycle
(d) none of the above
Ans: c

31. Inductance affects the direct current flow

(a) only at the time of turning off
(b) only at the time of turning on
(c) at the time of turning on and off
(d) at all the time of operation
Ans: c

32. Inductance of a coil Varies

(a) directly as the cross-sectional area of magnetic core
(b) directly as square of number of turns
(c) directly as the permeability of the core
(d) inversely as the length of the iron path
(e) as (a) to (d)
Ans: e

33. All the rules and laws of D.C. circuit also apply to A.C. circuit
containing
(a) capacitance only
(b) inductance only
(c) resistance only
(d) all above
Ans: c

34. Time constant of an inductive circuit

(a) increases with increase of inductance and decrease of
resistance
(b) increases with the increase of inductance and the increase of
resistance
(c) increases with decrease of inductance and decrease of
resistance
(d) increases with decrease of inductance and increase of
resistance
Ans: a

35. Power factor of an inductive circuit is usually improved by

connecting capacitor to it in
(a) parallel
(b) series
(c) either (a) or (b)
(d) none of the above
Ans: a

36. In a highly capacitive circuit the

(a) apparent power is equal to the actual power
(b) reactive power is more than the apparent power
(c) reactive power is more than the actual power
(d) actual power is more than its reactive power
Ans: c

37. Power factor of the following circuit will be zero

(a) resistance
(b) inductance
(c) capacitance
(d) both (b) and (c)
Ans: d

38. Power factor of the following circuit will be unity

(a) inductance
(b) capacitance
(c) resistance
(d) both (a) and (b)
Ans: c

39. Power factor of the system is kept high

(a) to reduce line losses
(b) to maximise the utilization of the capacities of generators,
lines and transformers
(c) to reduce voltage regulation of the line
(d) due to all above reasons
Ans: d

40. The time constant of the capacitance circuit is defined as the

time during which voltage
(a) falls to 36.8% of its final steady value
(b) rises to 38.6% of its final steady value
(c) rises to 63.2% of its final steady value
(d) none of the above
Ans: c

41. In a loss-free R-L-C circuit the transient current is

(a) oscillating
(b) square wave
(c) sinusoidal
(d) non-oscillating
Ans: c

42. The r.m.s. value of alternating current is given by steady

(D.C.) current which when flowing through a given circuit for a
given time produces
(a) the more heat than produced by A.C. when flowing through
the same circuit
(b) the same heat as produced by A.C. when flowing through the
same circuit
(c) the less heat than produced by A.C. flowing through the same
circuit
(d) none of the above
Ans: b
43. The square waveform of current has following relation
between r.m.s. value and average value.
(a) r.m.s. value is equal to average value
(b) r.m.s. value of current is greater than average value
(c) r.m.s. value of current is less than average value
(d) none of the above
Ans: a

44. The double energy transient occur in the

(a) purely inductive circuit
(b) R-L circuit
(c) R-C circuit
(d) R-L-C circuit
Ans: d

45. The transient currents are associated with the

(a) changes in the stored energy in the inductors and capacitors
(b) impedance of the circuit
(c) applied voltage to the circuit
(d) resistance of the circuit
Ans: a

46. The power factor at resonance in R-L- C parallel circuit is

(a) zero
(b) 0.08 lagging
(c) 0.8 leading
(d) unity
Ans: d

47. In the case of an unsymmetrical alternating current the

average value must always be taken over
(a) unsymmetrical part of the wave form
(b) the quarter cycle
(c) the half cycle
(d) the whole cycle
Ans: d

48. In a pure resistive circuit

(a) current lags behind the voltage by 90°
(b) current leads the voltage by 90°
(c) current can lead or lag the voltage by 90°
(d) current is in phase with the voltage
Ans: d

49. In a pure inductive circuit

(a) the current is in phase with the voltage
(b) the current lags behind the voltage by 90°
(c) the current leads the voltage by 90°
(d) the current can lead or lag by 90°
Ans: b

50. In a circuit containing R, L and C, power loss can take place in

(a) C only
(b) L only
(c) R only
(d) all above
Ans: c

51. Inductance of coil

(a) is unaffected by the supply frequency
(b) decreases with the increase in supply frequency
(c) increases with the increase in supply frequency
(d) becomes zero with the increase in supply frequency
Ans: c

52. In any A.C. circuit always

(a) apparent power is more than actual power
(b) reactive power is more than apparent power
(c) actual power is more than reactive power
(d) reactive power is more than actual power
Ans: a

53. Which of the following circuit component opposes the change

in the circuit voltage ?
(a) Inductance
(b) Capacitance
(c) Conductance
(d) Resistance
Ans:

54. In a purely inductive circuit

(a) actual power is zero
(b) reactive power is zero
(c) apparent power is zero
(d) none of above is zero
Ans: a

55. Power factor of electric bulb is

(a) zero
(b) lagging
(c) leading
(d) unity
Ans: d

56. Pure inductive circuit takes power from the A.C. line when
(a) applied voltage decreases but current increases
(b) applied voltage increases but current decreases
(c) both applied voltage and current increase
(d) both applied voltage and current decrease
Ans: a

57. Time constant of a circuit is the time in seconds taken after

the application of voltage to each
(a) 25% of maximum value
(b) 50% of maximum value
(c) 63% of maximum value
(d) 90% of the maximum value
Ans: c

58. Time constant of an inductive circuit

(a) increases with increase of inductance and decrease of
resistance
(b) increases with the increase of inductance and the increase of
resistance
(c) increases with the decrease of inductance and decrease of
resistance
(d) increases with decrease of inductance and increase of
resistance
Ans: a

59. Time constant of a capacitive circuit

(a) increases with the decrease of capacitance and decrease of
resistance
(b) increases with the decrease of capacitance and increase of
resistance
(c) increases with the increase of capacitance and decrease of
resistance
(d) increase with increase of capacitance and increase of
resistance
Ans: d

60. Magnitude of current at resonance in R-L-C circuit

(a) depends upon the magnitude of R
(b) depends upon the magnitude of L
(c) depends upon the magnitude of C
(d) depends upon the magnitude of R, Land C
Ans: a

Circuit Theory Objective Questions Pdf ::

61. In a R-L-C circuit
(a) power is consumed in resistance and is equal to I R
(b) exchange of power takes place between inductor and supply
line
(c) exchange of power takes place between capacitor and supply
line
(d) exchange of power does not take place between resistance
and the supply line
(e) all above are correct
Ans: e

62. In R-L-C series resonant circuit magnitude of resonance

frequency can be changed by changing the value of
(a) R only
(b) L only
(c)C only
(d)LorC
(e) R,LorC
Ans: d

63. In a series L-C circuit at the resonant frequency the

(a) current is maximum
(b) current is minimum
(c) impedance is maximum
(d) voltage across C is minimum
Ans: a

64. The time constant of a series R-C circuit is given by

(a) R/C
(b) RC2
(c) RC
(d) R2C
Ans: c

65. If resistance is 20 Q. and inductance is 27 in a R-L series

circuit, then time constant of this circuit will be
(a) 0.001 s
(b) 0.1 s
(c) 10 s
(d) 100 s
Ans: b

66. Which of the following coil will have large resonant

frequency ?
(a) A coil with large resistance
(b) A coil with low resistance
(c) A coil with large distributed capacitance
(d) A coil with low distributed capacitance
Ans: c

67. If a sinusoidal wave has frequency of 50 Hz with 30 A r.m.s.

current which of the following equation represents this wave ?
(a) 42.42 sin 3141
(b) 60 sin 25 t
(c) 30 sin 50 t
(d) 84.84 sin 25 t
Ans: a

68. The safest value of current the human body can carry for
more than 3 second is
(a) 4 mA
(b) 9 mA
(c) 15 mA
(d) 25 mA
Ans: b

69. A pure inductance connected across 250 V, 50 Hz supply

consumes 100 W.
This consumption can be attributed to
(a) the big size of the inductor
(b) the reactance of the inductor
(c) the current flowing in the inductor
(d) the statement given is false
Ans: d

70. The input of an A.C. circuit having power factor of 0.8 lagging
is 40 kVA
The power drawn by the circuit is
(a) 12 kW
(b) 22 kW
(c) 32 kW
(d) 64 kW
Ans: c

71. The effective resistance of an iron-cored choke working on

ordinary supply frequency is more than its true resistance
because of
(a) iron loss in core
(b) skin effect
(c) increase in temperature
(d) capacitive effect between adjacent coil turns
Ans: a
72. In an AC. circuit, a low value of kVAR compared with kW
indicates
(a) low efficiency
(b) high power factor
(c) unity power factor
(d) maximum load current
Ans: b

73. In AC. circuits, laminated iron is invariably used in order to

(a) reduce eddy current loss
(b) increase heat radiation
(c) make assembly cheap and easier
(d) reduce circuit permeability
Ans: a

74. The ratio of active power to apparent power is known as

factor.
(a) demand
(b) load
(c) power
(d) form
Ans: c

75. All definitions of power factor of a series R-L-C circuit are

correct except
(a) ratio of net reactance and impedance
(b) ratio of kW and kVA
(c) ratio of J and Z
(d) ratio of W and VA
Ans: a

76. The apparent power drawn by an A.C. circuit is 10 kVA and

active power is 8 kW. The reactive power in the circuit is
(a) 4 kVAR
(b) 6 kVAR
(c) 8 kVAR
(d) 16 kVAR
Ans: b
77. What will be the phase angle between two alternating waves
of equal frequency, when one wave attains maximum value the
other is at zero value ?
(a) 0°
(b) 45°
(c) 90°
(d) 180°
Ans: c

78. The purpose of a parallel circuit resonance is to magnify

(a) current
(b) voltage
(c) power
(d) frequency
Ans: b

79. In an A.C. circuit power is dissipated in

(a) resistance only
(b) inductance only
(c) capacitance only
(d) none of the above
Ans: a

80. In a parallel R-C circuit, the current always______the applied

voltage
(a) lags
(b) leads
(c) remains in phase with
(d) none of the above
Ans: b

81. At very low frequencies a series R-C circuit behaves as almost

purely
(a) resistive
(b) inductive
(c) capacitive
(d) none of the above
Ans: c
82. Skin effect occurs when a conductor carries current at_____
frequencies.
(a) very low
(b) low
(c) medium
(d) high
Ans: d

83. At ______ frequencies the parallel R-L circuit behaves as

purely resistive.
(a) low
(b) very low
(c) high
(d) very high
Ans: d

84. In a sine wave the slope is constant

(a) between 0° and 90°
(b) between 90° and 180°
(c) between 180° and 270°
(d) no where
Ans: d

85. The power is measured in terms of decibles in case of

(a) electronic equipment
(b) transformers
(c) current transformers
(d) auto transformers
Ans: a

86. Capacitive susceptance is a measure of

(a) reactive power in a circuit
(b) the extent of neutralisation of reactive power in a circuit
(c) a purely capacitive circuit’s ability to pass current
(d) a purely capacitive circuit’s ability to resist the flow of
current
Ans: c
87. Which of the following statements pertains to resistors only ?
(a) can dissipate considerable amount of power
(6) can act as energy storage devices
(c) connecting them in parallel in¬creases the total value
(d) oppose sudden changes in voltage
Ans: a

88. Which of the following refers to a parallel circuit ?

(a) The current through each element is same
(b) The voltage across element is in proportion to it’s resistance
value
(c) The equivalent resistance is greater than any one of the
resistors
(d) The current through any one element is less than the source
current
Ans: d

89. Aphasoris
(a) a line which represents the magnitude and phase of an
alternating quantity
(b) a line representing the magnitude and direction of an
alternating quantity
(c) a coloured tag or band for distinction between different
phases of a 3-phase supply
(d) an instrument used for measuring phases of an unbalanced
3-phase load
Ans: a

89. A parallel AC. circuit in resonance will

(a) have a high voltage developed across each inductive and
capacitive section
(b) have a high impedance
(c) act like a resistor of low value
(d) have current in each section equal to the line current
Ans: b

90. Wire-wound resistors are unsuitable for use at high

frequencies because they
(a) create more electrical noise
(b) are likely to melt under excessive eddy current heat
(c) consume more power
(d) exhibit unwanted inductive and capacitive effects
Ans: d

91. The inductance of a coil can be increased by

(a) increasing core length
(b) decreasing the number of turns
(c) decreasing the diameter of the former
(d) choosing core material having high relative permeability
Ans: d

92. In a three-phase supply floating neutral is undesirable

because it way give rise to
(a) high voltage across the load
(b) low voltage across the load
(c) unequal line voltages across the load
Ans: c

93. Which of the following waves has the highest value of peak
factor ?
(a) Square wave
(b) Sine wave
(c) Half wave rectified sine wave
(d) Triangular wave
Ans: c

94. The frequency of domestic power supply in India is

(a) 200 Hz
(b) 100 Hz
(c) 60 Hz
(d) 50 Hz
Ans: d

95. The r.m.s. value of half wave rectified sine wave is 200 V. The
r.m.s. value of full wave rectified AC. will be
(a) 282.8 V
(b) 141.4 V
(c) 111 V
(d) 100 V
Ans: a

96. The r.m.s. value of pure cosine function is

(a) 0.5 of peak value
(b) 0.707 of peak value
(c) same as peak value
(d) zero
Ans: b

97. Ohm is unit of all of the following except

(a) inductive reactance
(b) capacitive reactance
(c) resistance
(d) capacitance
Ans: d

98. The series and parallel resonance on L-C circuit’ differs in

that
(a) series resistance needs a low-resistance source for sharp rise
in current
(b) series resonance needs a high-resistance source for sharp
increase in current
(c) parallel resonance needs a low-resistance source for a sharp
in¬crease in impedance
(d) parallel resonance needs a low-resistance source for a sharp
rise in line current
Ans: a

99. The phosphors for which of the following pair are 180° out of
phase for VL, VC and VR?
(a) Vc and VR
(b) VL and VR
(c) Vc and VL
(d) none of the above
Ans: c

100. The frequency of an alternating current is

(a) the speed with which the alternator runs
(b) the number of cycles generated in one minute
(c) the number of waves passing through a point in one second
(d) the number of electrons passing through a point in one
second
Ans: c

101. A pure capacitor connected across an A.C. voltage consumed

50 W. This is due to
(a) the capacitive reactance in ohms
(b) the current flowing in capacitor
(c) the size of the capacitor being quite big
(d) the statement is incorrect
Ans: d

102. The power factor of a D.C. circuit is always

(a) less than unity
(b) unity
(c) greater than unity
(d) zero
Ans: b

103. The product of apparent power and cosine of the phase

angle between circuit voltage and current is
(a) true power
(b) reactive power
(c) volt-amperes
(d) instantaneous power
Ans: a

104. The equation of 50 Hz current sine wave having r.m.s. value

of 60 A is
(a) 60 sin 25 t
(b) 60 sin 50 t
(c) 84.84 sin 3141
(d) 42.42 sin 314 t
Ans: c

105. An A.C. voltage is impressed across a pure resistance of 3.5

ohms in parallel with a pure inductance of impedance of 3.5
ohms,
(a) the current through the resistance is more
(b) the current through the resistance is less
(c) both resistance and inductance carry equal currents
(d) none of the above
Ans: c

106. In a pure inductive circuit if the supply frequency is

reduced to 1/2, the current will
(a) be reduced by half
(b) be doubled
(c) be four times as high
(d) be reduced to one fourth
Ans: b

118. In a pure capacitive circuit if the supply frequency is

reduced to 1/2, the current will
(a) be reduced by half
(b) be doubled
(c) be four times at high
(d) be reduced to one fourth
Ans: a

119. When an alternating current passes through an ohmic

resistance the electrical power converted into heat is
(a) apparent power
(b) true power
(c) reactive power
(d) none of the above
Ans: b

120. In each of the three coils of a three phase generator, an

alternating voltage having an r.m.s. value of 220 V is induced.
Which of the following values is indicated by the voltmeters ?
(a) 220 V
(b) 220V3V
(c) 220/V3 V
(d) none of the above
Ans: a
 Comics
Read Over INSTALL
100,000
Comics.

Posted on August 19, 2018 by engineer 10 Comments

400+ TOP ELECTRICAL...

400+ TOP
ELECTRONICS and
COMMUNICATION...

[EEE] ELECTRICAL
ENGINEERING
Multiple Choice...

300+ TOP
INDUSTRIAL DRIVES
Objective Questions...

50 TOP INTEGRATED
CIRCUITS Questions
and Answers pdf |...

50 TOP POWER
ELECTRONICS
Questions and...
 300+ TOP BLOCKCHAIN Interview
Questions and Answers →

10 THOUGHTS ON “300+ TOP A.C. FUNDAMENTALS, CIRCUITS &

CIRCUIT THEORY MULTIPLE CHOICE QUESTIONS AND ANSWERS”

SUNIL C BIRADAR
JANUARY 13, 2017 AT 6:54 AM

please send me all questions and ans to my mail id sir

[email protected]

REPLY

LALIT KUMAR
DECEMBER 31, 2016 AT 5:12 AM

Sir please send me all electrical pdf questions my

REPLY

Fairoz Ahamed
DECEMBER 3, 2016 AT 11:22 PM

Sir please send me all Electrical questions to my Email

address: [email protected]

REPLY

Noor Islamn
NOVEMBER 5, 2016 AT 5:25 PM

Awesome sir, kindly send me MCQ,s on me email id, i

will be very thankful to you for this kindness.

REPLY

Er Prakash Dahal
OCTOBER 25, 2016 AT 6:15 AM
sir send me the all electrical objective in pdf
format….at my mail…[email protected]

REPLY

lingeshwaran
OCTOBER 1, 2016 AT 7:48 AM

Dr, sir i want iti objative electrical pdf questions all

ple send sir ple help me mail id:
[email protected]

REPLY

meghraj meena
JUNE 21, 2016 AT 8:57 AM

Sir please PDF all electrical question send

REPLY

Brijendra Pandey
MAY 27, 2016 AT 1:00 PM

Sir please send me all electrical questions in PDF for-

mat @ [email protected]

REPLY

vipin nanhe
MARCH 25, 2016 AT 10:24 AM

Q.53 answer is B.capacitance

Q.78. Right answer is A. Current…..magnifies current

REPLY

Ruhi Garg
SEPTEMBER 8, 2016 AT 11:11 AM
 sir plz send me all electrical questions in
[email protected]

REPLY

LEAVE A REPLY

Your email address will not be published. Required fields are marked *

Comment

Name *

Email *

Website

Post Comment

Engineering interview questions-multiple choice questions-objective type questions-seminor

topics-lab viva questions and answers-online quiz test pdf free download for freshers gate cat
syllabus pdf 2019.

Terms & Conditions | Privacy Policy | Contact us | About us