Scribd
Upload
113 views

Modbus Conversion

This document provides instructions for using a Microsoft Excel spreadsheet to interface with a Koyo PLC using Modbus protocol. It explains that only the numbers in red on the spreadsheet should be changed. It also notes that the Analysis Toolpak add-in must be enabled for the sheet to work correctly. The document includes tables that map the registers and coils of the Koyo PLC to their corresponding Modbus addresses.

Uploaded by

Ashraf Irfan
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
113 views

Modbus Conversion

This document provides instructions for using a Microsoft Excel spreadsheet to interface with a Koyo PLC using Modbus protocol. It explains that only the numbers in red on the spreadsheet should be changed. It also notes that the Analysis Toolpak add-in must be enabled for the sheet to work correctly. The document includes tables that map the registers and coils of the Koyo PLC to their corresponding Modbus addresses.

Uploaded by

Ashraf Irfan
Copyright
© © All Rights Reserved
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 7

Directions For use:

1. This spreadsheet was written using Microsoft Excel


97

2. Do not use preceding Y, X, C, etc... for PLC registers.


Just use the register/coil number
3. Only the RED numbers should be changed

4. For the sheet to work correctly, enable: Tools >> Add


Ins >> Analysis Toolpak (should be checked)
Coils
REMEMBER, NO EIGHTS OR
NINES!!! Koyo PLC Modbus
Global Outputs GY0 - GY3777 0 1 Coil 1 - 2048
Outputs - Y0 - Y1777 0 2049 Coil 2049 - 3072
Control Relay - C0 - C3777 0 3073 Coil 3073 - 5120
Stage - S0 - S1777 0 5121 Coil 5121 - 6144
Timer - T0 - T377 0 6145 Coil 6145 - 6400
Counter - CT0 - CT377 0 6401 Coil 6401 - 6656

Inputs
Global Inputs GX0 - GX3777 0 10001 Inputs 10001 - 12048
Inputs X0 - X1777 0 12049 Inputs 12049 - 13072
Special Register SP0 - SP777 0 13073 Inputs 13073 - 13584

Registers
Holding Input
PLC Registers Registers
V Memory 0 40001 30001 Holding Registers
Input Registers

Only the RED numbers should be changed.


Please refer to the "Function Code 4" sheet for information on RX and WX to the 30001 (In
Modbus Koyo PLC
1 0 Global Outputs - GY
2049 0 Outputs - Y
3073 0 Control Relay - C
5121 0 Stage - S
6145 0 Timer - T
6401 0 Counter - CT

10001 0 Global Inputs - GX


12049 0 Inputs - X
13073 0 Special Register - SP

Modbus V Memory
40001 0
30001 0

nd WX to the 30001 (Input Registers) with our PLCs.


Modbus
Modbus Modbus Coil Modbus
340 PLC Hex Decimal Decimal Decimal 340 PLC
Physical I/O 0 - 167 0 0 0 0 - 119 0 0
Control Relays 170 - 377 377 FF 255 120 - 255 120 170
Shift Register Bits 400 - 577 400 100 256 256 - 383 256 400
Timer/Counter Status 600 - 677 600 180 384 384 - 447 384 600
Physical IO 700 - 777 700 1C0 448 448 - 511 448 700
Control Relays 1000 - 1077 1077 23F 575 512 - 575 512 1000

User Registers 400 - 577 400 40 64 64 - 127 64 400


Timer/Counter Acc. 600 - 677 600 0 0 0 - 63 0 600
User Registers 700 - 777 700 80 128 128 - 191 128 700
NOTE: This is not necessary when using the MRX or MWX instructions. The MRX and MWX instructions allow you to
specify the function code you want to use.

NOTE: H2-ECOM100, H0-ECOM100, and H4-ECOM100 modules will also support Function 4 over ethernet. The
modules must have firmware versions equal to or greater than those listed below to support this. The feature is used by
requesting EVEN numbers of bytes for 40001+ addresses (function code 3) and ODD numbers of bytes for 30001+
addresses (function code 4).
H0-ECOM100 = 4.0.52
H2-ECOM100 = 4.0.999
H4-ECOM100 = 4.0.1049

You might also like