User's Manual: Model EJA510A and EJA530A Absolute Pressure and Gauge Pressure Transmitters (Style: S2)

User’s
Manual Model EJA510A and EJA530A

Absolute Pressure and
Gauge Pressure Transmitters
[Style: S2]
IM 01C21F01-01E
IM 01C21F01-01E
9th Edition
i
Model EJA510A and EJA530A

Absolute Pressure and Gauge Pressure Transmitters
[Style: S2]
IM 01C21F01-01E 9th Edition
Contents
1. Introduction................................................................................................ 1-1
 Regarding This Manual................................................................................................. 1-1
1.1 For Safe Use of Product ................................................................................... 1-2
1.2 Warranty.............................................................................................................. 1-3
1.3 ATEX Documentation........................................................................................ 1-4
2. Handling Cautions..................................................................................... 2-1
2.1 Model and Specifications Check...................................................................... 2-1
2.2 Unpacking........................................................................................................... 2-1
2.3 Storage................................................................................................................ 2-1
2.4 Selecting the Installation Location ................................................................. 2-1
2.5 Pressure Connection......................................................................................... 2-2
2.6 Waterproofing of Cable Conduit Connections............................................... 2-2
2.7 Restrictions on Use of Radio Transceiver...................................................... 2-2
2.8 Insulation Resistance and Dielectric Strength Test....................................... 2-2
2.9 Installation of Explosion Protected Type........................................................ 2-3
2.9.1 FM Approval........................................................................................ 2-3
2.9.2 CSA Certification................................................................................. 2-5
2.9.3 IECEx Certification.............................................................................. 2-7
2.9.4 ATEX Certification............................................................................... 2-8
2.10 EMC Conformity Standards............................................................................ 2-11
2.11 PED (Pressure Equipment Directive)............................................................ 2-11
2.12 Low Voltage Directive...................................................................................... 2-12
3. Component Names................................................................................... 3-1
4. Installation.................................................................................................. 4-1
4.1 Precautions ....................................................................................................... 4-1
4.2 Mounting ............................................................................................................ 4-1
4.3 Rotating Transmitter Section............................................................................ 4-2
4.4 Changing the Direction of Integral Indicator ................................................. 4-2
5. Installing Impulse Piping.......................................................................... 5-1
5.1 Impulse Piping Installation Precautions......................................................... 5-1
5.1.1 Connecting Impulse Piping to the Transmitter.................................... 5-1
5.1.2 Routing the Impulse Piping................................................................. 5-1
5.2 Impulse Piping Connection Examples............................................................ 5-2
9th Edition: July 2015 (KP) IM 01C21F01-01E

All Rights Reserved, Copyright © 1999, Yokogawa Electric Corporation
ii
6. Wiring.......................................................................................................... 6-1
6.1 Wiring Precautions............................................................................................ 6-1
6.2 Selecting the Wiring Materials.......................................................................... 6-1
6.3 Connections of External Wiring to Terminal Box........................................... 6-1
6.3.1 Power Supply Wiring Connection....................................................... 6-1
6.3.2 External Indicator Connection............................................................ 6-1
6.3.3 BRAIN TERMINAL BT200 Connection.............................................. 6-1
6.3.4 Check Meter Connection.................................................................... 6-2
6.4 Wiring.................................................................................................................. 6-2
6.4.1 Loop Configuration............................................................................. 6-2
6.4.2 Wiring Installation................................................................................ 6-2
6.5 Grounding........................................................................................................... 6-3
6.6 Power Supply Voltage and Load Resistance.................................................. 6-3
7. Operation.................................................................................................... 7-1
7.1 Preparation for Starting Operation.................................................................. 7-1
7.2 Zero Point Adjustment...................................................................................... 7-2
7.2.1 When you can obtain Low Range Value from actual measured
value of 0% (0 kPa, atmospheric pressure);....................................... 7-2
7.2.2 When you cannot obtain Low Range Value from actual measured
value of 0%;........................................................................................ 7-3
7.3 Starting Operation............................................................................................. 7-3
7.4 Shutting Down Operation................................................................................. 7-3
7.5 Setting the Range Using the Range-setting Switch....................................... 7-4
8. BRAIN TERMINAL BT200 Operation....................................................... 8-1
8.1 BT200 Operation Precautions.......................................................................... 8-1
8.1.1 Connecting the BT200........................................................................ 8-1
8.1.2 Conditions of Communication Line..................................................... 8-1
8.2 BT200 Operating Procedures........................................................................... 8-2
8.2.1 Key Layout and Screen Display.......................................................... 8-2
8.2.2 Operating Key Functions.................................................................... 8-2
8.2.3 Calling Up Menu Addresses Using the Operating Keys..................... 8-4
8.3 Setting Parameters Using the BT200............................................................... 8-5
8.3.1 Parameter Summary.......................................................................... 8-5
8.3.2 Parameter Usage and Selection......................................................... 8-8
8.3.3 Setting Parameters............................................................................. 8-9
(1) Tag No. Setup .................................................................................... 8-9
(2) Calibration Range Setup..................................................................... 8-9
(3) Damping Time Constant Setup . ...................................................... 8-10
(4) Output Signal Low Cut Mode Setup ................................................ 8-11
(5) Change Output Limits ...................................................................... 8-11
(6) Integral Indicator Scale Setup........................................................... 8-11
(7) Unit Setup for Displayed Temperature . ........................................... 8-13
IM 01C21F01-01E
iii
(8) Operation Mode Setup . ................................................................... 8-13
(9) Output Status Display/Setup when a CPU Failure .......................... 8-13
(10) Output Status Setup when a Hardware Error Occurs ..................... 8-13
(11) Range Change while Applying Actual Inputs ................................... 8-14
(12) Zero Point Adjustment ..................................................................... 8-14
(13) Span Adjustment............................................................................... 8-16
(14) Test Output Setup ............................................................................ 8-17
(15) User Memo Fields............................................................................. 8-17
8.4 Displaying Data Using the BT200................................................................... 8-17
8.4.1 Displaying Measured Data............................................................... 8-17
8.4.2 Display Transmitter Model and Specifications.................................. 8-17
8.5 Self-Diagnostics............................................................................................... 8-18
8.5.1 Checking for Problems..................................................................... 8-18
8.5.2 Errors and Countermeasures........................................................... 8-20
9. Maintenance............................................................................................... 9-1
9.1 Overview............................................................................................................. 9-1
9.2 Calibration Instruments Selection................................................................... 9-1
9.3 Calibration.......................................................................................................... 9-1
9.4 Disassembly and Reassembly......................................................................... 9-3
9.4.1 Replacing the Integral Indicator.......................................................... 9-3
9.4.2 Replacing the CPU Board Assembly.................................................. 9-4
9.4.3 Cleaning and Replacing the Capsule Assembly................................ 9-5
9.5 Troubleshooting................................................................................................. 9-6
9.5.1 Basic Troubleshooting........................................................................ 9-6
9.5.2 Troubleshooting Flow Charts.............................................................. 9-6
10. General Specifications........................................................................... 10-1
10.1 Standard Specifications.................................................................................. 10-1
10.2 Model and Suffix Codes.................................................................................. 10-3
10.3 Optional Specifications................................................................................... 10-4
10.4 Dimensions....................................................................................................... 10-6
Customer Maintenance Parts List
Model EJA510A and EJA530A
Absolute and Gauge Pressure Transmitter.................................... CMPL 01C21F01-01E
Revision Information
IM 01C21F01-01E
<1. Introduction> 1-1
1. Introduction
Thank you for purchasing the DPharp electronic
pressure transmitter. NOTE
The DPharp Pressure Transmitters are precisely For FOUNDATION FieldbusTM, PROFIBUS PA
calibrated at the factory before shipment. To ensure and HART protocol versions, please refer to
correct and efficient use of the instrument, please IM 01C22T02-01E, IM 01C22T03-00E and IM
read this manual thoroughly and fully understand 01C22T01-01E respectively, in addition to this
how to operate the instrument before operating it. manual.
• The following safety symbol marks are used in

 Regarding This Manual this manual:
• This manual should be passed on to the end
user.
• The contents of this manual are subject to WARNING
change without prior notice.
Indicates a potentially hazardous situation which,
• All rights reserved. No part of this manual may if not avoided, could result in death or serious
be reproduced in any form without Yokogawa’s injury.
written permission.
• Yokogawa makes no warranty of any kind with
regard to this manual, including, but not limited
to, implied warranty of merchantability and
CAUTION
fitness for a particular purpose. Indicates a potentially hazardous situation which,
• If any question arises or errors are found, or if if not avoided, may result in minor or moderate
any information is missing from this manual, injury. It may also be used to alert against unsafe
please inform the nearest Yokogawa sales practices.
office.
• The specifications covered by this manual are
IMPORTANT
limited to those for the standard type under the
specified model number break-down and do not Indicates that operating the hardware or software
cover custom-made instruments. in this manner may damage it or lead to system
• Please note that changes in the specifications, failure.
construction, or component parts of the
instrument may not immediately be reflected
in this manual at the time of change, provided NOTE
that postponement of revisions will not cause
Draws attention to information essential for
difficulty to the user from a functional or
understanding the operation and features.
performance standpoint.
• Yokogawa assumes no responsibilities for this
Direct current
product except as stated in the warranty.
• If the customer or any third party is harmed by
the use of this product, Yokogawa assumes
no responsibility for any such harm owing to
any defects in the product which were not
predictable, or for any indirect damages.
IM 01C21F01-01E
1.1 For Safe Use of Product (c) Operation
For the protection and safety of the operator • Wait 10 min. after power is turned off, before
and the instrument or the system including the opening the covers.
instrument, please be sure to follow the instructions
(d) Maintenance
on safety described in this manual when handling
this instrument. In case the instrument is handled in • Please do not carry out except being written
contradiction to these instructions, Yokogawa does to a maintenance descriptions. When these
not guarantee safety. Please give your attention to procedures are needed, please contact nearest
the followings. YOKOGAWA office.
• Care should be taken to prevent the build up of
(a) Installation
drift, dust or other material on the display glass
• The instrument must be installed by an expert and name plate. In case of its maintenance, soft
engineer or a skilled personnel. The procedures and dry cloth is used.
described about INSTALLATION are not
permitted for operators. (e) Explosion Protected Type Instrument
• In case of high process temperature, care • Users of explosion proof instruments should
should be taken not to burn yourself because refer first to section 2.9 (Installation of an
the surface of body and case reaches a high Explosion Protected Instrument) of this manual.
temperature. • The use of this instrument is restricted to those
• The instrument installed in the process is under who have received appropriate training in the
pressure. Never loosen the process connector device.
bolts to avoid the dangerous spouting of • Take care not to create sparks when accessing
process fluid. the instrument or peripheral devices in a
• During draining condensate from the hazardous location.
pressuredetector section, take appropriate care
to avoid contact with the skin, eyes or body, or (f) Modification
inhalation of vapors, if the accumulated process • Yokogawa will not be liable for malfunctions or
fluid may be toxic or otherwise harmful. damage resulting from any modification made
• When removing the instrument from hazardous to this instrument by the customer.
processes, avoid contact with the fluid and the
interior of the meter.
• All installation shall comply with local installation
requirement and local electrical code.
(b) Wiring
• The instrument must be installed by an expert
engineer or a skilled personnel. The procedures
described about WIRING are not permitted for
operators.
• Please confirm that voltages between the
power supply and the instrument before
connecting the power cables and that the
cables are not powered before connecting.
IM 01C21F01-01E
1.2 Warranty
• The warranty shall cover the period noted on
the quotation presented to the purchaser at the
time of purchase. Problems occurred during the
warranty period shall basically be repaired free
of charge.
• In case of problems, the customer should
contact the Yokogawa representative from
which the instrument was purchased, or the
nearest Yokogawa office.
• If a problem arises with this instrument,
please inform us of the nature of the problem
and the circumstances under which it
developed, including the model specification
and serial number. Any diagrams, data and
other information you can include in your
communication will also be helpful.
• Responsible party for repair cost for the
problems shall be determined by Yokogawa
based on our investigation.
• The Purchaser shall bear the responsibility for
repair costs, even during the warranty period, if
the malfunction is due to:
- Improper and/or inadequate maintenance by
the purchaser.
- Failure or damage due to improper handling,
use or storage which is out of design
conditions.
- Use of the product in question in a location
not conforming to the standards specified by
Yokogawa, or due to improper maintenance
of the installation location.
- Failure or damage due to modification or
repair by any party except Yokogawa or an
approved representative of Yokogawa.
- Malfunction or damage from improper
relocation of the product in question after
delivery.
- Reason of force majeure such as fires,
earthquakes, storms/floods, thunder/
lightening, or other natural disasters, or
disturbances, riots, warfare, or radioactive
contamination.
IM 01C21F01-01E
1.3 ATEX Documentation
This procedure is only applicable to the countries in European Union.
GB SK
CZ
DK
I LT
E LV
EST
NL
PL
SF
SLO
P
BG
RO
S
M
GR
IM 01C21F01-01E
<2. Handling Cautions> 2-1
2. Handling Cautions
This chapter describes important cautions 2.2 Unpacking
regarding how to handle the transmitter. Read
carefully before using the transmitter. When moving the transmitter to the installation site,
keep it in its original packaging. Then, unpack the
The EJA-A Series pressure transmitters are transmitter there to avoid damage on the way.
thoroughly tested at the factory before shipment.
When the transmitter is delivered, visually check
them to make sure that no damage occurred during 2.3 Storage
shipment. The following precautions must be observed when
Also check that all transmitter mounting hardware storing the instrument, especially for a long period.
shown in Figure 2.1 is included. If the transmitter (a) Select a storage area which meets the following
was ordered without the mounting bracket, the conditions:
transmitter mounting hardware is not included. After • It is not exposed to rain or water.
checking the transmitter, repack it in the way it was • It suffers minimum vibration and shock.
delivered until installation. • It has an ambient temperature and relative
Mounting bracket humidity within the following ranges.
U-bolt nut (S) (Flat type)
Plate Ambient temperature:
Adapter -40 to 85°C without integral indicator
-30 to 80°C with integral indicator
Relative humidity:
5% to 100% R.H. (at 40°C)
Preferred temperature and humidity:
approx. 25°C and 65% R.H.
(b) When storing the transmitter, repack it as nearly
U-bolt (L) as possible to the way it was packed when
delivered from the factory.
U-bolt (S)
(c) If storing a transmitter that has been used,
thoroughly clean the chambers inside the body,
U-bolt nut (L)
F0201.ai so that no measured fluid remains in it. Also
Figure 2.1 Transmitter Mounting Hardware make sure before storing that the transmitter
assemblies are securely mounted.
2.1 Model and Specifications 2.4 Selecting the Installation

Check Location
The model name and specifications are indicated The transmitter is designed to withstand severe
on the name plate attached to the case. If the environmental conditions. However, to ensure
reverse operating mode was ordered (reverse stable and accurate operation for years, observe
signal), ‘REVERSE’ will be inscribed in field *1. the following precautions when selecting an
installation location.
(a) Ambient Temperature
Avoid locations subject to wide temperature
variations or a significant temperature gradient.
: Refer to USER'S MANUAL If the location is exposed to radiant heat from
F0202.ai
plant equipments, provide adequate thermal
Figure 2.2 Name Plate
insulation and/or ventilation.
IM 01C21F01-01E
(b) Ambient Atmosphere 2.7 Restrictions on Use of Radio
Avoid installing the transmitter in a corrosive
atmosphere. If the transmitter must be installed
Transceiver
in a corrosive atmosphere, there must be
adequate ventilation as well as measures to
IMPORTANT
prevent intrusion or stagnation of rain water in Although the transmitter has been designed to
conduits. resist high frequency electrical noise, if a radio
(c) Shock and Vibration transceiver is used near the transmitter or its
Select an installation site suffering minimum external wiring, the transmitter may be affected
shock and vibration (although the transmitter is by high frequency noise pickup. To test for such
designed to be relatively resistant to shock and effects, bring the transceiver in use slowly from a
vibration). distance of several meters from the transmitter,
(d) Installation of Explosion-protected Transmitters and observe the measurement loop for noise
Explosion-protected transmitters can be effects. Thereafter, always use the transceiver
installed in hazardous areas according to the outside the area affected by noise.
types of gases for which they are certified.
See Subsection 2.9 “Installation of Explosion
Protected Type Transmitters.”
2.8 Insulation Resistance and
2.5 Pressure Connection Dielectric Strength Test
Since the transmitter has undergone insulation
WARNING resistance and dielectric strength tests at the
factory before shipment, normally these tests are
• Instrument installed in the process is not required. However, if required, observe the
under pressure. Never loosen the process following precautions in the test procedures.
connector bolts to avoid the dangerous
(a) Do not perform such tests more frequently than
spouting of process fluid.
is absolutely necessary. Even test voltages that
• During draining condensate from the
do not cause visible damage to the insulation
capsule assembly, take appropriate care to
may degrade the insulation and reduce safety
avoid contact with the skin, eyes or body,
margins.
or inhalation of vapors, if the accumulated
(b) Never apply a voltage exceeding 500 V DC
process fluid may be toxic or otherwise
(100 V DC with an internal lightning protector)
harmful.
for the insulation resistance test, nor a voltage
exceeding 500 V AC (100 V AC with an internal
The following precautions must be observed lightning protector) for the dielectric strength
in order to safely operate the transmitter under test.
pressure. (c) Before conducting these tests, disconnect
(a) Make sure that the process connection part is all signal lines from the transmitter terminals.
tightened firmly. Perform the tests in the following procedure:
(b) Make sure that there are no leaks in the impulse • Insulation Resistance Test
piping.
1) Short-circuit the + and – SUPPLY terminals in
(c) Never apply a pressure higher than the
the terminal box.
specified maximum working pressure.
2) Turn OFF the insulation tester. Then connect
the insulation tester plus (+) lead wire to the
2.6 Waterproofing of Cable shorted SUPPLY terminals and the minus (–)
Conduit Connections leadwire to the grounding terminal.
3) Turn ON the insulation tester power and
Apply a non-hardening sealant to the threads
measure the insulation resistance. The voltage
to waterproof the transmitter cable conduit
should be applied short as possible to verify
connections. (See Figure 6.7, 6.8 and 6.9.)
that the insulation resistance is at least 20 MΩ.
IM 01C21F01-01E
4) After completing the test and being very careful
not to touch exposed conductors disconnect the CAUTION
insulation tester and connect a 100 kΩ resistor
between the grounding terminal and the short- This instrument is tested and certified as
circuiting SUPPLY terminals. Leave this resistor intrinsically safe type or explosionproof
connected at least one second to discharge any type. Please note that the construction of
static potential. Do not touch the terminals while the instrument, installation, external wiring,
it is discharging. maintenance or repair is strictly restricted, and
non-observance or negligence of this restriction
• Dielectric Strength Test would result in dangerous condition.
1) Short-circuit the + and – SUPPLY terminals in
the terminal box.
2) Turn OFF the dielectric strength tester. Then WARNING
connect the tester between the shorted
SUPPLY terminals and the grounding terminal. To preserve the safety of explosionproof
Be sure to connect the grounding lead of the equipment requires great care during mounting,
dielectric strength tester to the ground terminal. wiring, and piping. Safety requirements also
3) Set the current limit on the dielectric strength place restrictions on maintenance and repair
tester to 10 mA, then turn ON the power and activities. Please read the following sections very
gradually increase the test voltage from ‘0’ to carefully.
the specified voltage.
4) When the specified voltage is reached, hold it
for one minute. 2.9.1 FM Approval
5) After completing this test, slowly decrease the
a. FM Intrinsically Safe Type
voltage to avoid any voltage surges.
Caution for FM intrinsically safe type. (Following
2.9 Installation of Explosion contents refer “DOC. No. IFM012-A12 P.1 and
2.”)
Protected Type
Note 1. Model EJA Series pressure transmitters
In this section, further requirements and differences with optional code /FS1 are applicable for
and for explosionproof type instrument are use in hazardous locations.
described. For explosionproof type instrument, • Applicable Standard: FM3600, FM3610,
the description in this chapter is prior to other FM3611, FM3810, ANSI/NEMA250
description in this users manual. • Intrinsically Safe for Class I, Division 1,
For the intrinsically safe equipment and Groups A, B, C & D. Class II, Division 1,
explosionproof equipment, in case the instrument Groups E, F & G and Class III, Division 1
is not restored to its original condition after any Hazardous Locations.
repair or modification undertaken by the customer, • Nonincendive for Class I, Division 2, Groups
intrinsically safe construction or explosionproof A, B, C & D. Class II, Division 2, Groups E,
construction is damaged and may cause dangerous F & G and Class III, Division 1 Hazardous
condition. Please contact Yokogawa for any repair Locations.
or modification required to the instrument. • Outdoor hazardous locations, NEMA 4X.
• Temperature Class: T4
NOTE • Ambient temperature: –40 to 60°C
Note 2. Entity Parameters
For FOUNDATION Fieldbus and PROFIBUS
• Intrinsically Safe Apparatus Parameters
PA explosion protected type, please refer to
[Groups A, B, C, D, E, F and G]
IM 01C22T02-01E and IM 01C22T03-00E
respectively. Vmax = 30 V Ci = 22.5 nF
Imax = 165 mA Li = 730 µH
Pmax = 0.9 W
IM 01C21F01-01E
* Associated Apparatus Parameters Note 4. Maintenance and Repair
(FM approved barriers) • The instrument modification or parts
Voc ≤ 30 V Ca > 22.5 nF replacement by other than authorized
Isc ≤ 165 mA La > 730 µH representative of Yokogawa Electric
Pmax ≤ 0.9W Corporation is prohibited and will void
Factory Mutual Intrinsically safe and
• Intrinsically Safe Apparatus Parameters
Nonincendive Approval.
[Groups C, D, E, F and G]
[Intrinsically Safe]
Vmax = 30 V Ci = 22.5 nF
Hazardous Location Nonhazardous Location
Imax = 225 mA Li = 730 µH
Class I, II, III, Division 1,
Pmax = 0.9 W Groups A, B, C, D, E, F, G General
* Associated Apparatus Parameters EJA Series Pressure Purpose
Transmitters Safety Barrier Equipment
(FM approved barriers) + + + +
Voc ≤ 30 V Ca > 22.5 nF – – – –
Supply
Isc ≤ 225 mA La > 730 µH
Pmax ≤ 0.9 W
• Entity Installation Requirements
[Nonincendive]
Vmax ≥ Voc or Vt, Imax ≥ Isc or It,
Pmax (IS Apparatus) ≥ Pmax (Barrier)
Class I, II, Division 2,
Ca ≥ Ci + Ccable, La ≥ Li + Lcable Groups A, B, C, D, E, F, G
Class III, Division 1. General
Note 3. Installation
EJA Series Pressure Purpose
• Barrier must be installed in an enclosure that Transmitters Equipment
meets the requirements of ANSI/ISA S82.01. + +
• Control equipment connected to barrier must Supply – –
not use or generate more than 250 V rms or Not Use
V dc. Safety Barrier
F0203.ai
• Installation should be in accordance with

ANSI/ISA RP12.6 “Installation of Intrinsically b. FM Explosionproof Type
Safe Systems for Hazardous (Classified) Caution for FM explosionproof type.
Locations” and the National Electric Code
(ANSI/NFPA 70). Note 1. Model EJA Series differential, gauge,
• The configuration of associated apparatus and absolute pressure transmitters with
must be FMRC Approved. optional code /FF1 are applicable for use in
• Dust-tight conduit seal must be used when hazardous locations.
installed in a Class II, III, Group E, F and G • Applicable Standard: FM3600, FM3615,
environments. FM3810, ANSI/NEMA250
• Associated apparatus manufacturer’s • Explosionproof for Class I, Division 1,
installation drawing must be followed when Groups B, C and D.
installing this apparatus. • Dust-ignitionproof for Class II/III, Division 1,
• The maximum power delivered from the Groups E, F and G.
barrier must not exceed 0.9 W. • Outdoor hazardous locations, NEMA 4X.
• Note a warning label worded • Temperature Class: T6
“SUBSTITUTION OF COMPONENTS MAY • Ambient Temperature: –40 to 60°C
IMPAIR INTRINSIC SAFETY,” and “INSTALL • Supply Voltage: 42 V dc max.
IN ACCORDANCE WITH DOC. No. IFM012- • Output signal: 4 to 20 mA
A12 P.1 and 2.”
IM 01C21F01-01E
Note 2. Wiring 2.9.2 CSA Certification
• All wiring shall comply with National Electrical
Code ANSI/NEPA70 and Local Electrical a. CSA Intrinsically Safe Type
Codes. Caution for CSA Intrinsically safe type.
• When installed in Division 1, “FACTORY (Following contents refer to “DOC No. ICS003-
SEALED, CONDUIT SEAL NOT A12 P.1-1 and P.1-2.”)
REQUIRED.”
Note 1. Model EJA Series differential, gauge,
Note 3. Operation and absolute pressure transmitters with
• Keep the “CAUTION” nameplate attached to optional code /CS1 are applicable for use
the transmitter. in hazardous locations
CAUTION: OPEN CIRCUIT BEFORE Certificate: 1053843
REMOVING COVER. SEAL ALL CONDUITS • Applicable Standard: C22.2 No.0, No.0.4,
WITHIN 18 INCHES. WHEN INSTALLED No.25, No.30, No.94, No.142, No.157,
IN DIV.1, “FACTORY SEALED, CONDUIT No.213
SEAL NOT REQUIRED.” INSTALL IN • Intrinsically Safe for Class I, Division 1,
ACCORDANCE WITH THE INSTRUCTION Groups A, B, C & D. Class II, Division 1,
MANUAL IM 1C22. Groups E, F & G and Class III, Division 1
• Take care not to generate mechanical Hazardous Locations.
sparking when accessing to the instrument • Nonincendive for Class I, Division 2, Groups
and peripheral devices in a hazardous A, B, C & D, Class II, Division 2, Groups F &
location. G, and Class III, Hazardous Locations. (not
Note 4. Maintenance and Repair use Safety Barrier)
• The instrument modification or parts • Encl. “Type 4X”
replacement by other than authorized • Temperature Class: T4
representative of Yokogawa Electric • Ambient temperature: –40* to 60°C
Corporation is prohibited and will void * –15°C when /HE is specified.
Factory Mutual Explosionproof Approval. • Process Temperature: 120°C max.
c. FM Intrinsically Safe Type/FM Note 2. Entity Parameters
Explosionproof Type • Intrinsically safe ratings are as follows:
Maximum Input Voltage (Vmax) = 30 V
Model EJA Series pressure transmitters with
Maximum Input Current (Imax) = 165 mA
optional code /FU1 can be selected the type
Maximum Input Power (Pmax) = 0.9 W
of protection (FM Intrinsically Safe or FM
Maximum Internal Capacitance (Ci) = 22.5nF
Explosionproof) for use in hazardous locations.
Maximum Internal Inductance (Li) = 730 µH
Note 1. For the installation of this transmitter, * Associated apparatus (CSA certified barriers)
once a particular type of protection is Maximum output voltage (Voc) ≤ 30 V
selected, any other type of protection Maximum output current (Isc) ≤ 165 mA
cannot be used. The installation must be in Maximum output power (Pmax) ≤ 0.9 W
accordance with the description about the
type of protection in this instruction manual.
• All wiring shall comply with Canadian
Note 2. In order to avoid confusion, unnecessary Electrical Code Part I and Local Electrical
marking is crossed out on the label other Codes.
than the selected type of protection when • The instrument modification or parts
the transmitter is installed. replacement by other than authorized
representative of Yokogawa Electric
Corporation and Yokogawa Corporation
of America is prohibited and will void
Canadian Standards Intrinsically safe and
nonincendive Certification.
IM 01C21F01-01E
[Intrinsically Safe] • When installed in Division 2, “SEALS NOT
Hazardous Location Nonhazardous Location REQUIRED.”
Class I, II, III, Division 1, Note 3. Operation
Groups A, B, C, D, E, F, G General • Keep the “CAUTION” label attached to the
Transmitters Safety Barrier Equipment
transmitter.
+ + + + CAUTION: OPEN CIRCUIT BEFORE
Supply – – – – REMOVING COVER.
OUVRIR LE CIRCUIT AVANT D´NLEVER
LE COUVERCLE.
• Take care not to generate mechanical
[Nonincendive] sparking when accessing to the instrument
Hazardous Location Nonhazardous Location and peripheral devices in a hazardous
Class I, II, Division 2, location.
Groups A, B, C, D, E, F, G
Class III, Division 1. General Note 4. Maintenance and Repair
• The instrument modification or parts
Transmitters Equipment
replacement by other than authorized
+ +
representative of Yokogawa Electric
Supply – –
Not Use Corporation and Yokogawa Corporation of
Safety Barrier America is prohibited and will void Canadian
F0204.ai
Standards Explosionproof Certification.
b. CSA Explosionproof Type Non-Hazardous Hazardous Locations Division 1
Locations
Caution for CSA explosionproof type.
Non-hazardous
Note 1. Model EJA Series differential, gauge, Location
Equipment 50 cm Max.
and absolute pressure transmitters with
optional code /CF1 are applicable for use
in hazardous locations:
42 V DC Max. Conduit
Certificate: 1089598 4 to 20 mA DC Sealing Fitting
• Applicable Standard: C22.2 No.0, No.0.4, Signal
EJA Series
No.25, No.30, No.94, No.142
• Explosionproof for Class I, Division 1, Non-Hazardous Hazardous Locations Division 2
Locations
Groups B, C and D.
Non-hazardous
• Dust-ignitionproof for Class II/III, Division 1, Location
Groups E, F and G. Equipment
• Encl “Type 4X”
• Temperature Class: T6, T5, and T4
• Process Temperature: 42 V DC Max.
4 to 20 mA DC Sealing Fitting
85°C (T6),100°C (T5), and 120°C (T4) Signal
• Ambient Temperature: –40* to 80°C EJA Series
F0205.ai
* –15°C when /HE is specified.
• Supply Voltage: 42 V dc max. c. CSA Intrinsically Safe Type/CSA
• Output Signal: 4 to 20 mA Explosionproof Type
Note 2. Wiring Model EJA Series pressure transmitters with
• All wiring shall comply with Canadian optional code /CU1 can be selected the type
Electrical Code Part I and Local Electrical of protection (CSA Intrinsically Safe or CSA
Codes. Explosionproof) for use in hazardous locations.
• In hazardous location, wiring shall be in
conduit as shown in the figure. Note 1. For the installation of this transmitter,
CAUTION: SEAL ALL CONDUITS WITHIN once a particular type of protection is
50 cm OF THE ENCLOSURE. selected, any other type of protection
UN SCELLEMENT DOIT ÊTRE INSTALLÉ À cannot be used. The installation must be in
MOINS DE 50 cm DU BîTIER. accordance with the description about the
type of protection in this instruction manual.
IM 01C21F01-01E
Note 2. In order to avoid confusion, unnecessary • Installation Requirements
marking is crossed out on the label other Uo ≤ Ui, Io ≤ Ii, Po ≤ Pi,
than the selected type of protection when Co ≥ Ci + Ccable, Lo ≥ Li + Lcable
the transmitter is installed. Uo, Io, Po, Co, and Lo are parameters of
barrier.
2.9.3 IECEx Certification
Model EJA Series differential, gauge, and absolute
• In any safety barreir used output current
pressure transmitters with optional code /SU2
must be limited by a resistor 'R' such that
can be selected the type of protection (IECEx
Io=Uo/R.
Intrinsically Safe/type n or flameproof) for use in
• The safety barrier must be IECEx certified.
hazardous locations.
• Input voltage of the safety barrier must be
Note 1. For the installation of this transmitter, less than 250 Vrms/Vdc.
once a particular type of protection is • The instrument modification or parts
selected, any other type of protection replacement by other than authorized
cannot be used. The installation must be in representative of Yokogawa Electric
accordance with the description about the Corporation and will void IECEx Intrinsically
type of protection in this instruction manual. safe and type n certification.
• The cable entry devices and blanking
Note 2. In order to avoid confusion, unnecessary elements for type n shall be of a certified type
marking is crossed out on the label other providing a level of ingress protection of at
than the selected type of protection when least IP54, suitable for the conditions of use
the transmitter is installed. and correctly installed.
a. IECEx Intrinsically Safe Type / type n • Electrical Connection:
The type of electrical connection is stamped
Caution for IECEx Intrinsically safe and type n. near the electrical connection port according
Note 1. Model EJA Series differential, gauge, to the following marking.
and absolute pressure transmitters with
Screw Size Marking
optional code /SU2 are applicable for use
ISO M20 × 1.5 female M
in hazardous locations.
• No. IECEx KEM 06.0007X ANSI 1/2 NPT female A
• Applicable Standard: IEC 60079-0:2004,
IEC 60079-11:1999, IEC 60079-15:2005,
IEC 60079-26:2004
• Type of Protection and Marking Code:
Ex ia IIC T4, Ex nL IIC T4 Location of the marking
• Ambient Temperature: –40 to 60°C
• Max. Process Temp.: 120°C F0206.ai
• Enclosure: IP67
Note 4. Operation
Note 2. Entity Parameters • WARNING:
• Intrinsically safe ratings are as follows: WHEN AMBIENT TEMPERATURE ≥ 55°C,
Maximum Input Voltage (Ui) = 30 V USE THE HEAT-RESISTING CABLES ≥
Maximum Input Current (Ii) = 165 mA 90°C.
Maximum Input Power (Pi) = 0.9 W
Maximum Internal Capacitance (Ci) = 22.5nF Note 5. Special Conditions for Safe Use
Maximum Internal Inductance (Li) = 730 µH • WARNING:
• Type “n” ratings are as follows: IN THE CASE WHERE THE ENCLOSURE
Maximum Input Voltage (Ui) = 30 V OF THE PRESSURE TRANSMITTER IS
Maximum Internal Capacitance (Ci) = 22.5nF MADE OF ALUMINUM, IF IT IS MOUNTED
Maximum Internal Inductance (Li) = 730 µH IN AN AREA WHERE THE USE OF ZONE
0 IS REQUIRED, IT MUST BE INSTALLED
SUCH, THAT, EVEN IN THE EVENT OF
RARE INCIDENTS, IGNITION SOURCES
DUE TO IMPACT AND FRICTION SPARKS
ARE EXCLUDED.
IM 01C21F01-01E
[Intrinsically Safe] Note 3. Operation
Hazardous Location Nonhazardous Location • WARNING:
Group I/IIC, Zone 0 AFTER DE-ENERGIZING, DELAY 10
General MINUTES BEFORE OPENING.
EJA Series Pressure IECEx certified Purpose • WARNING:
Transmitters Safety Barrier Equipment WHEN AMBIENT TEMPERATURE ≥ 70°C,
+ + + +
USE THE HEAT-RESISTING CABLES ≥
Supply – – – –
90°C.
sparking when accessing to the instrument
[type n] and peripheral devices in a hazardous
Hazardous Location Nonhazardous Location location.
Group IIC, Zone 2 Note 4. Maintenance and Repair
EJA Series Pressure IECEx Certified
Transmitters Equipment [nL] replacement by other than authorized
+ + representative of Yokogawa Electric
Supply – – Corporation is prohibited and will void IECEx
Not Use Certification.
Safety Barrier
F0207.ai 2.9.4 ATEX Certification
b. IECEx Flameproof Type (1) Technical Data
Caution for IECEx flameproof type.
a. ATEX Intrinsically Safe Type
and absolute pressure transmitters with Caution for ATEX Intrinsically safe type.
optional code /SU2 are applicable for use Note 1. Model EJA Series differential, gauge,
in hazardous locations: and absolute pressure transmitters with
• No. IECEx KEM 06.0005 optional code /KS2 for potentially explosive
• Applicable Standard: IEC60079-0:2004, atmospheres:
IEC60079-1:2003 • No. KEMA 02ATEX1030 X
• Type of Protection and Marking Code: • Applicable Standard: EN 50014:1997,
Ex d IIC T6...T4 EN 50020:1994, EN 50284:1999
• Enclosure: IP67 • Type of Protection and Marking code:
• Maximum Process Temperature: EEx ia IIC T4
120°C (T4), 100°C (T5), 85°C (T6) • Temperature Class: T4
• Ambient Temperature: –40 to 75°C (T4), • Enclosure: IP67
–40 to 80°C (T5), –40 to 75°C (T6) • Process Temperature: 120°C max.
• Supply Voltage: 42 V dc max. • Ambient Temperature: –40 to 60°C
• Output Signal: 4 to 20 mA dc
Note 2. Electrical Data
Note 2. Wiring • In type of explosion protection intrinsic
• In hazardous locations, the cable entry safety EEx ia IIC only for connection to a
devices shall be of a certified flameproof certified intrinsically safe circuit with following
type, suitable for the conditions of use and maximum values:
correctly installed. Ui = 30 V
• Unused apertures shall be closed with Ii = 165 mA
suitable flameproof certified blanking Pi = 0.9 W
elements. (The plug attached is certificated Effective internal capacitance; Ci = 22.5 nF
as the flame proof IP67 as a part of this Effective internal inductance; Li = 730 µH
apparatus.)
• In case of ANSI 1/2 NPT plug, ANSI
hexagonal wrench should be applied to
screw in.
IM 01C21F01-01E
Note 3. Installation Note 2. Electrical Data
• All wiring shall comply with local installation • Supply voltage: 42 V dc max.
requirements. (Refer to the installation • Output signal: 4 to 20 mA
diagram)
Note 4. Maintenance and Repair • All wiring shall comply with local installation
• The instrument modification or parts requirement.
replacement by other than authorized • The cable entry devices shall be of a certified
representative of Yokogawa Electric flameproof type, suitable for the conditions of
Corporation is prohibited and will void KEMA use.
Intrinsically safe Certification.
Note 4. Operation
Note 5. Special Conditions for Safe Use • Keep the “CAUTION” label to the transmitter.
• In the case where the enclosure of the CAUTION: AFTER DE-ENERGIZING,
Pressure Transmitter is made of aluminium, DELAY 10 MINUTES BEFORE OPENING.
if it is mounted in an area where the use of WHEN THE AMBIENT TEMP.≥70°C, USE
category 1 G apparatus is required, it must HEAT-RESISTING CABLES ≥ 90°C.
be installed such, that, even in the event of • Take care not to generate mechanical
rare incidents, ignition sources due to impact sparking when accessing to the instrument
and friction sparks are excluded. and peripheral devices in a hazardous
location.
[Installation Diagram]

Note 5. Maintenance and Repair
Transmitter
replacement by other than authorized
+ + representative of Yokogawa Electric
Supply Safety Barrier *1 Corporation is prohibited and will void KEMA
– – Flameproof Certification.
(2) Electrical Connection
The type of electrical connection is stamped
F0208.ai near the electrical connection port according to
*1: In any safety barriers used the output current must be the following marking.
limited by a resistor “R” such that Imaxout-Uz/R.
Screw Size Marking
b. ATEX Flameproof Type ISO M20 × 1.5 female M
Caution for ATEX flameproof type. ANSI 1/2 NPT female A

and absolute pressure transmitters
with optional code /KF21 for potentially
explosive atmospheres:
Location of the marking
• No. KEMA 02ATEX2148
• Applicable Standard: EN 60079-0:2006,
F0206.ai
EN 60079-1:2004
• Type of Protection and Marking Code:
Ex d IIC T6...T4
• Temperature Class: T6, T5, and T4
• Enclosure: IP67
• Maximum Process Temperature:
85°C (T6), 100°C (T5), and 120°C (T4)
• Ambient Temperature:
T4 and T6; –40* to 75°C, T5; –40* to 80°C
* –15°C when /HE is specified.
IM 01C21F01-01E
(3) Installation (6) Name Plate
 Name plate
WARNING
• All wiring shall comply with local installation
requirement and local electrical code.
• There is no need of the conduit seal for : Refer to USER'S MANUAL
both of Division 1 and Division 2 hazardous

locations because this product is sealed at  Tag plate for flameproof type
factory.
• In case of ANSI 1/2 NPT plug, ANSI
hexagonal wrench should be applied to
screw in.
 Tag plate for intrinsically safe type
(4) Operation
WARNING F0210.ai
MODEL: Specified model code.

• OPEN CIRCUIT BEFORE REMOVING
STYLE: Style code.
COVER. INSTALL IN ACCORDANCE WITH
SUFFIX: Specified suffix code.
THIS USER’S MANUAL
SUPPLY: Supply voltage.
OUTPUT: Output signal.
sparking when access to the instrument and
MWP: Maximum working pressure.
peripheral devices in hazardous locations.
CAL RNG: Specified calibration range.
DISP MODE: Specified display mode.
(5) Maintenance and Repair OUTPUT MODE: Specified output mode.
NO.: Serial number and year of production*1.
TOKYO 180-8750 JAPAN:
WARNING The manufacturer name and the address*2.
The instrument modification or parts replacement *1: The third figure from the last shows the last one figure
of the year of production. For example, the production
by other than authorized Representative of year of the product engraved in “NO.” column on the
Yokogawa Electric Corporation is prohibited and name plate as follows is 2001.
will void the certification. 12A819857 132
The year 2001

*2: “180-8750” is a zip code which represents the
following address.
2-9-32 Nakacho, Musashino-shi, Tokyo Japan
IM 01C21F01-01E
2.10 EMC Conformity Standards Model
PS*1
V(L)
PS-V
Category*2
(bar) (bar-L)
EN 61326-1 Class A, Table 2 (For use in industrial Article 3, paragraph 3
EJA110A 160 0.01 1.6
locations) (SEP)
Article 3, paragraph 3
EN 61326-2-3 EJA120A 0.5 0.01 0.005
(SEP)
EN 61326-2-5 (for Fieldbus) EJA130A 420 0.01 4.2
(SEP)
EJA130A
420 0.01 4.2 III
CAUTION With code /PE3
EJA310A 160 0.01 1.6
(SEP)
This instrument is a Class A product, and it is
designed for use in the industrial environment. EJA430A 160 0.01 1.6
(SEP)
Please use this instrument in the industrial Article 3, paragraph 3
EJA440A 500 0.01 50
environment only. (SEP)
EJA440A
500 0.01 50 III
With code /PE3
EJA510A 500 0.01 50
(SEP)
NOTE EJA510A With
500 0.01 50 III
code /PE3
YOKOGAWA recommends customer to apply Article 3, paragraph 3
the Metal Conduit Wiring or to use the twisted EJA530A 500 0.01 50
(SEP)
pair Shield Cable for signal wiring to conform the EJA530A
500 0.01 50 III
requirement of EMC Regulation, when customer With code /PE3
installs the EJA Series Transmitters to the plant. *1: PS is maximum allowable pressure for vessel itself.
*2: Referred to Table 1 covered by ANNEX II of EC Directive
on Pressure Equipment Directive 97/23/EC
(3) Operation
2.11 PED (Pressure Equipment
Directive) CAUTION
(1) General • The temperature and pressure of fluid should
• EJA series of pressure transmitters are be applied under the normal operating
categorized as pressure accessories under the condition.
vessel section of this directive 97/23/EC, which • The ambient temperature should be applied
corresponds to Article 3, Paragraph 3 of PED, under the normal operating condition.
denoted as Sound Engineering Practice (SEP).. • Please pay attention to prevent the
• EJA130A, EJA440A, EJA510A, and EJA530A excessive pressure like water hammer,
can be used above 200 bar and therefore etc. When water hammer is to be occurred,
considered as a part of a pressure retaining please take measures to prevent the
vessel where category lll, Module H applies. pressure from exceeding PS by setting the
These models with option code /PE3 conform safety valve, etc. at the system and the like.
to that category. • When external fire is to be occurred, please
take safety measures at the device or
(2) Technical Data
system not to influence the transmitters.
• Models without /PE3
Article 3, Paragraph 3 of PED, denoted as
Sound Engineering Practice (SEP) .
• Models with /PE3
Module: H
Type of Equipment: Pressure Accessory-Vessel
Type of Fluid: Liquid and Gas
Group of Fluid: 1 and 2
IM 01C21F01-01E
2.12 Low Voltage Directive
Applicable standard: EN 61010-1
(1) Pollution Degree 2

“Pollution degree” describes the degree to
which a soild, liquid, or gas which deteriorates
dielectric strength or surface resistivity
is adhering. “2” applies to normal indoor
atmosphere. Normally, only non-conductive
pollution occurs. Occasionally, however,
temporary conductivity caused by condenstaion
must be expected.
(2) Installation Category I
“Overvoltage category (Installation category)”
describes a number which defines a transient
overvoltage condition. It implies the regulattion
for impulse withstand voltage. “I” applies to
electrical equipment which is supplied from the
circuit when appropriate transient overvoltage
control means (interfaces) are provided.
(3) Altitude of installation site:
Max. 2,000 m above sea level
(4) Indoor/Outdoor use
IM 01C21F01-01E
<3. Component Names> 3-1
3. Component Names
External indicator Transmitter section
conduit connection (Note 1)
Terminal box cover
CPU assembly
Zero-adjustment screw
Integral
indicator (Note 1)
Mounting screw Pipe (Open to atmosphere)
(Note 3)
Setting pin (CN4) Capsule assembly
Range-setting
switch (Note 1)
(See Subsection 7.5)
Amplifier Cover
Setting Pin (CN4) Burn-Out Output at
Position (Note 2) Direction Burn-Out
H
110% or
HIGH higher
L
H
-5% or
LOW lower
L
F0301.ai
Note 1: See Subsection 10.2, “Model and Suffix Codes,” for details.
Note 2: Insert the pin (CN4) as shown in the figure above to set the burn-out direction. The pin is set to the H side for delivery (unless
option code /C1 is specified in the order).
The setting can be confirmed by calling up parameter D52 using the BRAIN TERMINAL. Refer to Subsection 8.3.3 (8).
Note 3: Applied to Model EJA530A with Measurement span code A, B, and C.
Figure 3.1 Component Names
Table 3.1 Display Symbol

Display Symbol Meaning of Display Symbol
The output signal being zero-adjusted is increasing.
The output signal being zero-adjusted is decreasing.
%, Pa, kPa, MPa, kgf/cm2, gf/cm2, mbar, bar, atm,
Select one of these sixteen available engineering units for the display.
mmHg, mmH2O, inH2O, inHg, ftH2O, psi, Torr
F0302.ai
IM 01C21F01-01E
<4. Installation> 4-1
4. Installation
4.1 Precautions Vertical pipe mounting
Before installing the transmitter, read the cautionary
notes in Section 2.4, “Selecting the Installation
Adapter
Location.” For additional information on the ambient
conditions allowed at the installation location, refer
U-bolt (S) Plate
to Subsection 10.1 “Standard Specifications.”
U-bolt nut (S)
IMPORTANT
• When welding piping during construction,
take care not to allow welding currents to U-bolt nut (L)
flow through the transmitter.
• Do not step on this instrument after Mounting bracket
installation. 50 mm(2-inch) pipe U-bolt (L)
Horizontal pipe mounting

4.2 Mounting
■ The impulse piping connection port of the Adapter
transmitter is covered with a plastic cap to
protect against dust. This cap must be removed U-bolt (S) Plate
before connecting the piping. (Be careful not
U-bolt nut (S)
to damage the threads when removing these
caps. Never insert a screw driver or other
tool between the cap and the port threads to
remove the cap.)
U-bolt nut (L)
■ The transmitter can be mounted on a nominal
50 mm (2-inch) pipe using the mounting bracket
Mounting bracket
supplied, as shown in Figure 4.1.
50 mm(2-inch) pipe U-bolt (L)
■ The user should prepare the mating gasket for
F0401.ai
the transmitters with Process connection code
Figure 4.1 Transmitter Mounting
8 and 9. See Figure 4.2.
Gasket
F0402.ai
Figure 4.2 Gasketing
IM 01C21F01-01E
<4. Installation> 4-2
IMPORTANT IMPORTANT
Tighten the hexagonal nut part of the capsule Do not rotate the transmitter section more than
assembly. See Figure 4.3. 180°.
Transmitter section
Rotate 90° or 180° segments
Capsule assembly
Conduit connection
Gasket
Pipe
Allen screw Capsule assembly

F0404.ai
Figure 4.4 Rotating Transmitter Section

F0403.ai
Figure 4.3 Tightening Transmitter

4.4 Changing the Direction of
Integral Indicator
4.3 Rotating Transmitter Section
The DPharp transmitter section can be rotated in
IMPORTANT
90° segments. Always turn OFF power, release pressure and
1) Remove the two Allen screws that fasten the remove a transmitter to non-hazardous area
transmitter section and capsule assembly, before disassembling and reassembling an
using the Allen wrench. Also, remove the pipe indicator.
for the model EJA530A with Measurement span
code A, B, and C, using the slotted screwdriver. An integral indicator can be installed in the following
2) Rotate the transmitter section slowly in 90° three directions. Follow the instructions in section
segments. 9.4 for removing and attaching the integral indicator.
3) Tighten the two Allen screws to a torque of 5
N·m, and replace the pipe if applied.
F0405.ai
Figure 4.5 Integral Indicator Direction
IM 01C21F01-01E
<5. Installing Impulse Piping> 5-1
5. Installing Impulse Piping

5.1 Impulse Piping Installation
NOTE
Precautions
• If the process fluid is a gas, the taps must be
5.1.1 Connecting Impulse Piping to the vertical or within 45° either side of vertical.
Transmitter • If the process fluid is a liquid, the taps must
be horizontal or below horizontal, but not
IMPORTANT more than 45° below horizontal.
• If the process fluid is steam or other
The transmitter can be installed in horizontal condensing vapor, the taps must be
impulse piping configuration, tilting the horizontal or above horizontal, but not more
transmitter's position up to 90°. When tilting, than 45° above horizontal.
observe that the zero-adjustment screw and the [Gas] [Liquid] [Steam]
pipe (for Model EJA530A with Measurement
45° 45°
span code A, B, and C) are positioned
Pressure 45° 45°
downwards, as shown in Figure 5.1. taps
45° 45°
Process
piping
F0502.ai
Figure 5.2 Process Pressure Tap Angle

(For Horizontal Piping)
Pipe Zero-adjustment screw

(Open to atmosphere) (2) Position of Process Pressure Taps and
F0501.ai
Transmitter
Figure 5.1 Horizontal Impulse Piping Connection
If condensate (or gas) accumulates in the impulse
piping, it should be removed periodically by
5.1.2 Routing the Impulse Piping
opening the drain (or vent) plugs. However, this will
(1) Process Pressure Tap Angles generate a transient disturbance in the pressure
measurement, and therefore it is necessary to
If condensate, gas, sediment or other extraneous position the taps and route the impulse piping so
material in the process piping gets into the impulse that any extraneous liquid or gas generated in the
piping, pressure measurement errors may result. To leadlines returns naturally to the process piping.
prevent such problems, the process pressure taps
must be angled as shown in Figure 5.2 according to • If the process fluid is a gas, then as a rule the
the kind of fluid being measured. transmitter must be located higher than the
process pressure taps.
• If the process fluid is a liquid or steam, then as a
rule the transmitter must be located lower than
the process pressure taps.
IM 01C21F01-01E
<5. Installing Impulse Piping> 5-2
(3) Impulse Piping Slope
Tap valve
The impulse piping must be routed with only an
upward or downward slope. Even for horizontal
routing, the impulse piping should have a slope of Union or flange
Stop valve
at least 1/10 to prevent condensate (or gases) from
accumulating in the pipes.
(4) Preventing Freezing

Tee
If there is any risk that the process fluid in the Stop valve
impulse piping or transmitter could freeze, use a Union or flange
steam jacket or heater to maintain the temperature Drain valve
of the fluid.
Drain plug
F0503.ai
NOTE Figure 5.3 Impulse Piping Connection Examples
After completing the connections, close the

valves on the process pressure taps (main
valves), the valves at the transmitter (stop
valves), and the impulse piping drain valves,
so that condensate, sediment, dust and other
extraneous material cannot enter the impulse
piping.
5.2 Impulse Piping Connection

Examples
Figure 5.3 shows examples of typical impulse
piping connections. Before connecting the
transmitter to the process, study the transmitter
installation location, the process piping layout,
and the characteristics of the process fluid
(corrosiveness, toxicity, flammability, etc.), in order
to make appropriate changes and additions to the
connection configurations.
Note the following points when referring to these
piping examples.
• If the impulse piping is long, bracing or supports
should be provided to prevent vibration.
• The impulse piping material used must
be compatible with the process pressure,
temperature, and other conditions.
• A variety of process pressure tap valves (main
valves) are available according to the type
of connection (flanged, screwed, welded),
construction (globe, gate, or ball valve),
temperature and pressure. Select the type of
valve most appropriate for the application.
IM 01C21F01-01E
<6. Wiring> 6-1
6. Wiring
6.1 Wiring Precautions 6.3 Connections of External
Wiring to Terminal Box
IMPORTANT
• Lay wiring as far as possible from electrical
6.3.1 Power Supply Wiring Connection
noise sources such as large capacity Connect the power supply wiring to the SUPPLY +
transformers, motors, and power supplies. and – terminals.
• Remove electrical connection dust cap
Transmitter terminal box
before wiring. +
• All threaded parts must be treated with Power supply
waterproofing sealant. (A non-hardening –
silicone group sealant is recommended.)

• To prevent noise pickup, do not pass signal F0601.ai
and power cables through the same ducts. Figure 6.1 Power Supply Wiring Connection
• Explosion-protected instruments must
be wired in accordance with specific 6.3.2 External Indicator Connection
requirements (and, in certain countries,
legal regulations) in order to preserve the Connect wiring for external indicators to the CHECK
effectiveness of their explosionprotected + and – terminals.
features. (Note) Use a external indicator whose internal resistance is 10Ω
or less.
• The terminal box cover is locked by an Allen
head bolt (a shrouding bolt) on CENELEC External indicator
Power supply
and IECEx flameproof type transmitters. +
When the shrouding bolt is driven clockwise
–
by an Allen wrench, it is going in and cover
lock is released, and then the cover can
be opened by hand. See Subsection 9.4
“Disassembly and Reassembly” for details. F0602.ai
Figure 6.2 External Indicator Connection
6.2 Selecting the Wiring 6.3.3 BRAIN TERMINAL BT200

Materials Connection
(a) Use stranded leadwires or cables which are Connect the BT200 to the SUPPLY + and
the same as or better than 600 V grade PVC – terminals (Use hooks). The communication line
insulated wire (JIS C3307) or equivalent. requires a reception resistor of 250 to 600Ω in
(b) Use shielded wires in areas that are susceptible series.
to electrical noise. Transmitter terminal box Power supply
(c) In areas with higher or lower ambient +
temperatures, use appropriate wires or cables. –
(d) In environment where oils, solvents, corrosive
Ignore the polarity
gases or liquids may be present, use wires or since the BT200 is
cables that are resistant to such substances. AC-coupled to the
BT200 terminal box.
(e) It is recommended that crimp-on solderless
F0603.ai
terminal lugs (for 4 mm screws) with insulating
Figure 6.3 BT200 Connection
sleeves be used for leadwire ends.
IM 01C21F01-01E
<6. Wiring> 6-2
6.3.4 Check Meter Connection (2) Intrinsically Safe Type
Connect the check meter to the CHECK + and For intrinsically safe type, a safety barrier must be
– terminals (use hooks). included in the loop.
• A 4 to 20 mA DC output signal from the CHECK Hazardous Location Nonhazardous Location
+ and – terminals.
(Note) Use a check meter whose internal resistance is 10Ω or Transmitter terminal box
less. Distributor
(Power supply unit)
Power supply
+ Receiver
instrument
– +
–
Check meter
Transmitter terminal box Safety barrier
F0604.ai F0606.ai
Figure 6.4 Check Meter Connection Figure 6.6 Connection between Transmitter and
Distributor
6.4 Wiring 6.4.2 Wiring Installation
6.4.1 Loop Configuration (1) General-use Type and Intrinsically Safe

Type
Since the DPharp uses a two-wire transmission
system, signal wiring is also used as power wiring. Make cable wiring using metallic conduit or
waterproof glands.
DC power is required for the transmitter loop. The
transmitter and distributor are connected as shown • Apply a non-hardening sealant to the terminal
below. box connection port and to the threads on the
flexible metal conduit for waterproofing.
For details of the power supply voltage and load
resistance, see Section 6.6; for communications Apply a non-hardening
line requirements, see Subsection 8.1.2. sealant to the threads for
waterproofing.
(1) General-use Type and Flameproof Type

Wiring metal
Hazardous Location Nonhazardous Location conduit
Tee
Distributor
(Power supply unit)
Drain plug
Receiver Flexible metal conduit

+ instrument
F0607.ai
–
F0605.ai
Figure 6.7 Typical Wiring Using Flexible Metal
Figure 6.5 Connection between Transmitter and Conduit
Distributor
IM 01C21F01-01E
<6. Wiring> 6-3
(2) Flameproof Type 6.5 Grounding
Wire cables through a flameproof packing adapter, Grounding is always required for the proper
or using a flameproof metal conduit. operation of transmitters. Follow the domestic
■ Wiring cable through flameproof packing adapter. electrical requirements as regulated in each
• Apply a nonhardening sealant to the terminal country. For a transmitter with built-in lightning
box connection port and to the threads on the protector, grounding should satisfy ground
flameproof packing adapter for waterproofing. resistance of 10Ω or less.
Ground terminals are located on the inside and
Apply a non-hardening
sealant to the threads for outside of the terminal box. Either of these terminals
waterproofing. may be used.
Wiring metal
conduit
Ground terminal
(Inside)
Tee
Drain plug
Flexible metal conduit
Flameproof packing adapter

F0608.ai Ground terminal
(Outside)
Figure 6.8 Typical Cable Wiring Using Flameproof
Packing Adapter
F0610.ai
■ Flameproof metal conduit wiring Figure 6.10 Ground Terminals

• A seal fitting must be installed near the terminal
box connection port for a sealed construction.
• Apply a non-hardening sealant to the threads of 6.6 Power Supply Voltage and
the terminal box connection port, flexible metal
conduit and seal fitting for waterproofing. Load Resistance
Non-hazardous area
When configuring the loop, make sure that the
Gas sealing device
external load resistance is within the range in the
Apply a non-hardening figure below.
sealant to the threads of (Note) In case of an intrinsically safe transmitter, external load
these fittings for resistance includes safety barrier resistance.
Hazardous area waterproofing
600
Flameproof
heavy-gauge External E–10.5
steel conduit load R= Communication
0.0236
resistance applicable range
R (Ω) BRAIN and HART
Tee
Flameproof flexible
Drain plug
metal conduit 250
Seal fitting
After wiring, impregnate the fitting
with a compound to seal tubing.
F0609.ai
Figure 6.9 Typical Wiring Using Flameproof Metal

Conduit 0 10.5 16.4 24.7 42
Power supply voltage E (V DC)
F0611.ai
Figure 6.11 Relationship between Power Supply

Voltage and External Load Resistance
IM 01C21F01-01E
<7. Operation> 7-1
7. Operation
7.1 Preparation for Starting  Confirming that Transmitter is Operating
Properly
Operation
This section describes the operation procedure for Using the BT200
measuring a pressure as shown in Figure 7.1.
• If the wiring system is faulty, ‘communication
error’ appears on the display.
NOTE • If the transmitter is faulty, ‘SELF CHECK
ERROR’ appears on the display.
Confirm that the process pressure tap valve,
drain valve, and stop valve are closed. PARAM
C60:SELF CHECK
ERROR
communication error
(a) Introduce a process fluid into the impulse piping
and then to the transmitter in the following
procedure: DATA DIAG PRNT ESC
1) Open the tap valve (main valve) to fill the Communication error Self-diagnostic error
(Faulty wiring) (Faulty transmitter)
impulse piping with process fluid. F0702.ai
2) Gradually open the stop valve to introduce

process fluid into the transmitter pressure- Using the integral indicator
detector section.
• If the wiring system is faulty, the display stays
3) Confirm that there is no pressure leak in
blank.
the impulse piping, transmitter, or other
• If the transmitter is faulty, an error code will
components.
appear on the display according to the nature of
(b) Turn ON power and connect the BT200.
the error.
(c) Using the BT200, confirm that the transmitter
is operating properly. Check parameter values
or change the setpoints as necessary. See
Chapter 8 for BT200 operation.
Union or flange
Self-diagnostic error on
Vent plug (Fill plug) the integral indicator
(Faulty transmitter)
F0703.ai
Tap valve
NOTE
Stop valve If any of the error indications above appears on
the display of the integral indicator or BT200,
refer to Subsection 8.5.2 for corrective action.
Tee
 Verify and Change Transmitter
Union or flange Parameter Setting and Values
Drain valve
The following parameters are the minimum settings
Drain plug required for operation. The transmitter has been
F0701.ai
shipped with these parameters. To confirm or
Figure 7.1 Liquid Flow Measurement (Gauge change the values, see Subsection 8.3.3.
Pressure Transmitters)
• Measuring range … See Subsection 8.3.3 (2)
• Operation mode … See Subsection 8.3.3 (7)
IM 01C21F01-01E
<7. Operation> 7-2
7.2 Zero Point Adjustment 7.2.1 When you can obtain Low Range
Value from actual measured value of
Adjust the zero point after operating preparation is
0% (0 kPa, atmospheric pressure);
completed.
For pressure measurement using gauge pressure
IMPORTANT transmitters, follow the step below before zero point
adjustment.
Do not turn off the power to the transmitter
1) Close the tap valve (main valve).
immediately after a zero adjustment. Powering
2) Loosen the fill plug so that the pressure applied
off within 30 seconds after a zero adjustment
to the transmitter is only the head of the seal
will return the adjustment back to the previous
liquid.
settings.
3) Adjust the zero point at this status.
4) After the adjustment, close the fill plug and then
The zero point adjustment can be made in either
gradually open the tap valve.
way: using the zero-adjustment screw of the
transmitter or the BT200 operation.
 Using the Transmitter Zero-adjustment
For output signal checking, display the parameter Screw
A10: OUTPUT (%) in the BT200.
Before adjusting a screw, check that the parameter
 BT200 J20: EXT ZERO ADJ displays ENABLE. See
PARAM Output signal (%)
Subsection 8.3.3 (11) for the setting procedure.
A10:OUTPUT(%)
display
0.0 %
A11:ENGR OUTPUT
Use a slotted screwdriver to turn the zero-
A20:AMP TEMP
adjustment screw. Turn the screw clockwise
to increase the output or counterclockwise to
DATA DIAG PRNT ESC decrease the output.
The zero point adjustment can be made with a
 Zero-adjustment Screw resolution of 0.01% of the setting range. Since
the degree of zero adjustments varies with the
screw turning speed, turn the screw slowly for fine
adjustment and quickly for coarse adjustment.
 Using the BT200

Zero point can be adjusted by simple key operation
F0704.ai of the BT200.
After reviewing this parameter you are prepared Select parameter J10: ZERO ADJ, and press the
to adjust the zero point. When making the zero ENTER key twice. The zero point will be adjusted
adjustment on a pressure transmitter, the process automatically to the output signal 0% (4 mA DC).
pressure value does not have to be set to the low Confirm that the setting value displayed for the
limit of the measurement range (0%). In such case, parameter is ‘0.0%’ before pressing the ENTER
adjust the transmitter output signal to the actual key. See Subsection 8.3.3 (11) for BT200 operating
measured value obtained from a high-accuracy procedures.
pressure measuring instrument. A display when parameter
SET
J10:ZERO ADJ
-0.0 % J10 is selected.
+ 000.0
Press key
twice for 0% output 4 mA DC.
CLR ESC
F0705.ai
IM 01C21F01-01E
<7. Operation> 7-3
7.2.2 When you cannot obtain Low Range 7.3 Starting Operation
Value from actual measured value of
After completing the zero point adjustment, follow
0%;
the procedure below to start operation.
Convert the actual measured value obtained by a
1) Confirm the operating status. If the output
digital manometer or a glass gauge into %.
signal exhibits wide fluctuations (hunting) due
[Example] to periodic variation in the process pressure,
use BT200 to dampen the transmitter output
The measuring range of 50 to 250 kPa; the actual signal. Confirm the hunting using a receiving
measured value of 130 kPa. instrument or the integral indicator, and set
130–50 the optimum damping time constant. See
Actual measured value= x 100=40.0% Subsection 8.3.3 (3), “Damping Time Constant
250–50
Setup.”
2) After confirming the operating status, perform
 Using the Transmitter Zero-Adjustment the following.
Screw
Turn the screw to match the output signal to the IMPORTANT
actual measured value in %.
• Remove the BT200 from the terminal box,
 Using the BT200 and confirm that none of the terminal screws
are loosened.
Select the parameter J10: ZERO ADJ. Change • Close the terminal box cover and the
the set point (%) displayed for the parameter to the amplifier cover. Screw each cover in tightly
actual measured value (%), and press the ENTER until it will not turn further.
key twice. See Subsection 8.3.3 (11) for operation • Two covers are required to be locked on
details. the CENELEC and IECEx Flameproof type
SET Display at J10 transmitters. An Allen head bolts (shrouding
J10:ZERO ADJ
-0.0 % bolts) are provided under edge of the
+ 000.0
each cover for locking. When a shrouding
bolts are driven counterclockwise by an
CLR ESC
Allen wrench, it is coming out and locks
up a cover. (See page 9-4) After locking,
the covers should be confirmed not to be
SET
J10:ZERO ADJ opened by hand.
-0.0 % Change setting to the actually
+ 040.0 • Tighten the zero-adjustment cover mounting
measured value (40.0%).
screw to fix the cover in position.
Press key twice
CLR ESC for 40% output 10.4 mA DC.
F0706.ai
7.4 Shutting Down Operation
Shut down the transmitter operation as follows.
1) Turn off the power.
2) Close the stop valve.
3) Close the tap valve.
NOTE
Whenever shutting down the transmitter for a
long period, remove any process fluid from the
transmitter pressure-detector section.
IM 01C21F01-01E
<7. Operation> 7-4
7.5 Setting the Range Using the IMPORTANT
Range-setting Switch
• Do not turn off the power to the transmitter
With actual pressure being applied to the immediately after completion of the change
transmitter, the range-setting switch (push-button) in the LRV and/or HRV setting(s). Note
located on the optional /E integral indicator plate that powering off within thirty seconds after
and the external zero-adjustment screw allow users setting will cause a return to the previous
to change (re-range) the low- and high-limit values settings.
for the measurement range (LRV and HRV) without • Changing LRV automatically changes HRV
using BT200. However, other changes in the to the following value.
display settings (scale range and engineering unit)
for the integral indicator requires BT200. HRV =
previous HRV + (new LRV – previous LRV)
Follow the procedure below to change the LRV and
HRV settings. • If the range-setting push-button and external
zero-adjustment screw are not touched
[Example] during a range-change operation, the
transmitter automatically switches back to
Rerange LRV to 0 and HRV to 3 MPa.
the normal operation mode.
1) Connect the transmitter and apparatus as
shown in Figure 9.1 and warm up for at least Integral indicator
five minutes.
2) Press the range-setting push-button. The Note : Use a thin bar which
has a blunt tip, e.g.,
integral indicator then displays “LSET.” a hexagonal wrench,
3) Apply a pressure of 0 kPa (atmospheric to press the range-
setting push-button
pressure) to the transmitter. (Note 1)
4) Turn the external zero-adjustment screw in the
desired direction. The integral indicator displays
Range-setting switch
the output signal in %. (Note 2) (Push-button)
5) Adjust the output signal to 0% (1 V DC) by F0707.ai
rotating the external zero-adjustment screw. Figure 7.2 Range-setting Switch

Doing so completes the LRV setting.
6) Press the range-setting push-button. The
integral indicator then displays “HSET.”
7) Apply a pressure of 3 MPa to the transmitter.
(Note 1)
8) Turn the external zero-adjustment screw in the
desired direction. The integral indicator displays
the output signal in %. (Note 2)
9) Adjust the output signal to 100% (5 V DC) by
rotating the external zero-adjustment screw.
Doing so completes the HRV setting.
10) Press the range-setting push-button. The
transmitter then switches back to the normal
operation mode with the measurement range of
0 to 3 MPa.
Note 1: Wait until the pressure inside the pressure-detector
section has stabilized before proceeding to the next step.
Note 2: If the pressure applied to the transmitter exceeds the
previous LRV (or HRV), the integral indicator may display
error number “Er.07” (In this case, the output signal
percent and “Er.07” are displayed alternately every two
seconds).
Although “Er.07” is displayed, you may proceed to the
next step. However, should any other error number be
displayed, take the appropriate measure in reference to
Subsection 8.5.2, “Errors and Countermeasures.”
IM 01C21F01-01E
<8. BRAIN TERMINAL BT200 Operation> 8-1
8. BRAIN TERMINAL BT200 Operation

The DPharp is equipped with BRAIN • Note for Connecting the BT200
communications capabilities, so that range
changes, Tag No. setup, monitoring of self- IMPORTANT
diagnostic results, and zero point adjustment can
be handled by remote control via BT200 BRAIN • Analog output may change temporally in
TERMINAL or CENTUM CS console. This section connecting with BRAIN terminal due to
describes procedures for setting parameters using an initial current flowed to it. To prevent
the BT200. For details concerning the BT200, see communication signal affecting the upper
IM 01C00A11-01E, “BT200 User’s Manual.” system, it is recommended to install a low-
pass filter (approximately 0.1s).
• Communication signal is superimposed on
8.1 BT200 Operation analog output signal. It is recommended
to set a low-pass filter (approximately
Precautions
0.1s) to the receiver in order to reduce the
8.1.1 Connecting the BT200 output effect from communication signal.
Before online-communication, confirm that
The transmitter and the BT200 can be connected communication signal does not give effect on
either to the BT200 connection hooks in the the upper system.
transmitter terminal box or to a relaying terminal
board.
8.1.2 Conditions of Communication Line
• Communication Line Requirements

Control room [Protocol specification] Yokogawa original
Relaying
terminals protocol
Terminal board
[Modulation] Burst modulation
0: 2400Hz
Distributor 1: Signal without carrier
[Baud rate] 1200bps
[Communication signal]
host to device: +/- 0.5V (load resistance 250Ω)
F0801.ai device to host: +/- 2mA
Figure 8.1 Connecting the BT200
Cable resistance Rc
Power
supply
cc
Load Cable DPharp

resistance R resistance Rc
● Loop resistance = R + 2Rc

= 250 to 600Ω
● Loop capacitance = 0.22 µF max. BT200
F0802.ai
Figure 8.2 Conditions of Communication Line
IM 01C21F01-01E
8.2 BT200 Operating Procedures 8.2.2 Operating Key Functions
8.2.1 Key Layout and Screen Display (1) Alphanumeric Keys and Shift Keys
Figure 8.3 shows the arrangement of the operating You can use the alphanumeric keys in conjunction
keys on the BT200 keypad, and Figure 8.4 shows with the shift keys to enter symbols, as well as
the BT200 screen component. alphanumeric keys.
LCD
(21 character × 8 lines) Alphanumeric keys
Shift keys F0805.ai
Function keys a. Entering Digits, Symbols, and Spaces

(0 to 9, ., 2, )
Movement keys
Simply press the alphanumeric keys.
ENTER key
Entry Key-in Sequence
Power ON/OFF key –4
0.3
Alphanumeric keys
1 –9
F0806.ai
b. Entering Letters (A through Z)

Shift keys
F0803.ai Press an alphanumeric key following a shift key to
Figure 8.3 BT200 Key Layout enter the letter shown on that side which the shift
key represents. You must press the shift key before
MENU SCREEN
Messages entering each letter.
MENU BATTERY
A:DISPLAY
B:SENSOR TYPE Left-side letter on the Right-side letter on
Menu choices alphanumeric key the alphanumeric key
Screen title
HOME SET ADJ ESC
PARAMETER SCREEN Entry Key-in Sequence

PARAM W
A10:OUTPUT Function
100.0 %
Parameters A11:ENGR. OUTPUT commands IC
1000 mmH20
A20:AMP TEMP
23 deg C J. B
DATA DI AG PRNT
F0807.ai
F0804.ai
Figure 8.4 BT200 Screen Component Use the function key [F2] to select between
CAPS
uppercase and lowercase (for letters only). The

case toggles between uppercase and lowercase
each time you press [F2] CAPS.
Entering uppercase Entering lowercase

CODE CAPS CLR ESC CODE caps CLR ESC

to lower case
Boy
(B) (o) (y)
F0808.ai
IM 01C21F01-01E
Use the function key [F1] CODE to enter symbols.
The following symbols will appear in sequence, one
at a time, at the cursor each time you press [F1]
CODE:
/ . − , + * ) ( ’ & % $ # ” !
To enter characters next to these symbols, press [>]
to move the cursor.
symbol command
l/m
(I) (/) (m)
F0809.ai
(2) Function Keys

The functions of the function keys depend on the
function commands on display.
MENU
A:DISPLAY
B:SENSOR TYPE
HOME SET ADJ ESC Function commands
Function keys
F0810.ai
Function Command List

Command Function
ADJ Displays the ADJ menu
CAPS/caps Selects uppercase or lowercase
CODE Selects symbols
CLR Erases input data or deletes all data
DATA Updates parameter data
DEL Deletes one character
DIAG Calls the self-check panel
ESC Returns to the most recent display
HOME Displays the menu panel
NO Quits setup and returns to the previous
display
OK Proceeds to the next panel
PARM Enters the parameter number setup mode
SET Displays the SET menu
SLOT Returns to the slot selection panel
UTIL Calls the utility panel
*COPY Prints out parameters on display
*FEED Paper feed
*LIST Lists all parameters in the menu
*PON/ Automatic printout mode on or off
POFF
*PRNT Changes to the print mode
*GO Starts printing
*STOP Cancels printing
* Available on BT200-P00 (with printer).
IM 01C21F01-01E
8.2.3 Calling Up Menu Addresses Using the Operating Keys
--WELCOME-- UTILITY The utility screen contains the

BRAIN TERMINAL 1.ID following items.
ID: BT200 2.SECURITY CODE
STARTUP 3.LANGUAGE SELECT 1. BT200 ID settings
SCREEN check connection 4.LCD CONTRAST 2. Security code settings
push ENTER key 5.PRINTER ADJUST
3. Switching language of messages
UTIL FEED esc (Japanese or English)
4. LCD contrast setting
5. Adjusting printout tone
(UTIL)
(BT200-P00 only)
PARAM
01:MODEL
EJA510A-DC
INITIAL 02:TAG NO. FUNC
DATA YOKOGAWA 1.MENU
SCREEN 03:SELF CHECK (ESC) 2.UPLOAD TO BT200
GOOD 3.DOWNLOAD TO INST
OK 4.PRINT ALL DATA
HOME SET ADJ ESC
(SET) (ADJ)
(HOME MENU SCREEN) (SET MENU SCREEN) (ADJ MENU SCREEN)
MENU MENU MENU
A.DISPLAY C.SETTING J.ADJUST
B.SENSOR TYPE D.AUX SET 1 K.TEST
MENU E.AUX SET 2 M.MEMO
SCREEN H:AUTO SET P:RECORD
HOME SET ADJ ESC HOME SET ADJ ESC HOME SET ADJ ESC
PARAM PARAM
A60:SELF CHECK C60:SELF CHECK
GOOD GOOD
PARAM PARAM PARAM

A21:CAPSULE TEMP C22:HIGH RANGE J60:SELF CHECK
PARA- 26.5 deg C 100 kPa GOOD
METER DATA DIAG PRNT ESC DATA DIAG PRNT ESC
SCREEN
PARAM PARAM PARAM
A10:OUTPUT(%) C10:TAG NO. J10:ZERO ADJ
50.0 % YOKOGAWA 0.0 %
DATA DIAG
A11:ENGR, PRNT
OUTPUT ESC DATA DIAG
C20:PRESS UNITPRNT ESC DATA DIAG
J11:ZERO DEV PRNT ESC
20.0 M kPa 22.2 %
A20:AMP TEMP C21:LOW RANGE J20:EXT. ZERO ADJ
24.5 deg C 0 kPa ENABLE
DATA DIAG PRNT ESC DATA DIAG PRNT ESC DATA DIAG PRNT ESC
SET See “BT200 Instruction Manual” for details

C10:TAG NO. concerning uploading and downloading parameters
SETUP YOKOGAWA
SCREEN YOKOGAWA and printouts (BT200-P00).
CODE CAPS CLR ESC

F0811.ai
IM 01C21F01-01E
8.3 Setting Parameters Using the BT200
8.3.1 Parameter Summary
Instruments to which applicable:
F: Differential pressure transmitters EJA110A, EJA120A, and EJA130A
P: Pressure transmitters EJA310A, EJA430A, EJA440A, EJA510A, and EJA530A
L: Liquid level transmitters EJA210A and EJA220A
Applica-
Rewrita- bility
No. Item Description Remarks Default Value
bility
F P L
01 MODEL Model+capsule type –   
02 TAG NO. Tag number – 16 alphanumerics   
03 SELF CHECK Self-diagnostic result – GOOD/ERROR   
A DISPLAY Measured data display – Menu name   
A10 OUTPUT (%) Output (in %) – –5 to 110%*3   
A11 ENGR. OUTPUT Output (in engineering units) – –19999 to 19999   
A20 AMP TEMP Amplifier temperature – Unit specified in D30   
A21 CAPSULE Capsule temperature – Unit specified in D30   
TEMP
A30 STATIC PRESS Static pressure – Unit specified in D31*1  – 
A40 INPUT Input (indicated as the value – –32000 to 32000   
after zeroing)
A60 SELF CHECK Self-diagnostic messages – GOOD/ERROR, CAP MODULE FAULT, AMP   
MODULE FAULT, OUT OF RANGE, OUT OF SP
RANGE*1, OVER TEMP (CAP), OVER TEMP (AMP),
OVER OUTPUT, OVER DISPLAY, ILLEGAL LRV,
ILLEGAL HRV, ILLEGAL SPAN, and ZERO ADJ OVER
B SENSOR TYPE Sensor type – Menu name   
B10 MODEL Model+span – 16 uppercase alphanumerics   
B11 STYLE NO. Style number –   
B20 LRL Lower range-limit – –32000 to 32000   
B21 URL Upper range-limit – –32000 to 32000   
B30 MIN SPAN Minimum span – –32000 to 32000   
B40 MAX STAT.P. Maximum static pressure*6 –  – 
B60 SELF CHECK Self-diagnostic messages – Same as A60   
C SETTING Setting data – Menu name   
C10 TAG. NO. Tag number  16 alphanumerics As specified when   
ordered.
C20 PRESS UNIT Measurement range units  Selected from mmH2O, As specified when   
mmAq, mmWG, mmHg, Torr, ordered.
Pa, hPa, kPa, MPa, mbar, bar,
gf/cm2, kgf/cm2, inH2O, inHg,
ftH2O, psi, or atm
C21 LOW RANGE Measurement range, lower  –32000 to 32000(but within As specified when   
range value measurement range) ordered.
C22 HIGH RANGE Measurement range, higher  –32000 to 32000(but within As specified when   
range value measurement range) ordered.
C30 AMP DAMPING Damping time constant  Selected from 0.2*2, 0.5, 1.0, 2.0 s   
2.0, 4.0, 8.0, 16.0, 32.0, or
64.0 sec.
C40 OUTPUT MODE Output mode and integral  Selected from OUT:LIN; DSP: As specified when  – –
indicator mode LIN, OUT:LIN; DSP:SQR, ordered.
OUT:SQR; DSP:SQR If not specified, OUT:
LIN; DSP: LIN.
C60 SELF CHECK Self-diagnostic messages – Same as A60   
IM 01C21F01-01E
Applica-
Rewrita- bility
bility
F P L
D AUX SET 1 Auxiliary setting data 1 – Menu name   
D10 LOW CUT Low cut  0.0 to 20.0% 10.0%   
D11 LOW CUT Low cut mode  LINEAR/ZERO LINEAR   
MODE
D15 OUT LIMIT(L) Lower output range-limit  –5.0 to 110.0% –5.0%*7   
D16 OUT LIMIT(H) Upper output range-limit  –5.0 to 110.0% 110.0%   
D20 DISP SELECT Display selection  NORMAL %/USER SET, As specified when   
USER & %/INP PRES, PRES ordered.
&%
D21 DISP UNIT Engineering unit for display  8 uppercase alphanumerics   
D22 DISP LRV Engineering range, lower  –19999 to 19999 As specified when   
range value ordered.
D23 DISP HRV Engineering range, higher  –19999 to 19999 As specified when   
range value ordered.
D30 TEMP UNIT Temperature setting units  deg C/deg F deg C   
D31 STAT. P. UNIT Static pressure setting units  Selected from mmH2O, As specified when  – 
mmAq, mmWG, mmHg, Torr, ordered. If not
Pa, hPa, kPa, MPa, mbar, bar, specified, MPa.
gf/cm2, kgf/cm2, inH2O, inHg,
ftH2O, psi, or atm
D40 REV OUTPUT Output reversal  NORMAL/REVERSE If not specified,   
NORMAL.
D45 H/L SWAP Impulse piping accessing  NORMAL/REVERSE*4 NORMAL  – –
direction
D52 BURN OUT CPU error – HIGH/LOW, –5 to 110%*3 HIGH   
D53 ERROR OUT Hardware error  HOLD/HIGH/LOW, HIGH   
–5 to 110%*3
D60 SELF CHECK Self-diagnostic messages – Same as A60   
E AUX SET 2 Auxiliary setting data 2 – Menu name   
E10 DFS MODE DFS mode  OFF/ON*5 ON   –
E14 TEMP SELECT Reference temperature  AMP. TEMP/CAP. TEMP*5 CAP. TEMP   –
sensor
E15 TEMP ZERO Zero shift conpensation  ±10.00*5 0.00   –
setup
E30 BI DIRE MODE Bidirectional mode  OFF/ON OFF  – –
E50 AUTO Auto-recover from sensor  OFF/ON ON   
RECOVER error
E60 SELF CHECK Self-diagnostic messages – Same as A60   
H AUTO SET Automatic setup – Menu name   
H10 AUTO LRV Automatic measurement  –32000 to 32000 Displays the same   
range lower range value data as C21.
setup
H11 AUTO HRV Automatic measurement  –32000 to 32000 Displays the same   
range higher range value data as C22.
setup
H60 SELF CHECK Self-diagnostic messages – Same as A60   
J ADJUST Adjustment data – Menu name   
J10 ZERO ADJ Automatic zero adjustment  –5 to 110.0%*3   
J11 ZERO DEV. Manual zero adjustment    
J15 SPAN ADJ Manual span adjustment  –10.00 to 10.00% 0.00%   
J20 EXT. ZERO ADJ External zero-adjustment  ENABLE/INHIBIT   
screw permission
J30 AOUTPUT 4mA 4mA adjustment  –10.00 to 10.00% 0.00%   
J31 OUTPUT 20mA 20mA adjustment  –10.00 to 10.00% 0.00%   
J60 ASELF CHECK Self-diagnostic messages – Same as A60   
K TEST Tests – Menu name   
K10 OUTPUT in % Test output % setting  –5 to 110.0%*3 Displays   
‘ACTIVE’ while executing
K60 SELF CHECK Self-diagnostic messages – Same as A60   
IM 01C21F01-01E
Applica-
Rewrita- bility
bility
F P L
M MEMO Memo – Menu name   
M10 MEMO 1 Memo  8 uppercase alphanumerics   
M60 SELF CHECK Self-diagnostic messages – Same as A60   
P RECORD History of the errors –   
P10 ERROR REC 1 Last error  Display the error   
P11 ERROR REC 2 One time before  Display the error   
P12 ERROR REC 3 Two time before  Display the error   
P13 ERROR REC 4 Three time before  Display the error   
P60 SELF CHECK Self-diagnostic messages – Same as A60   
*1: In case of Model EJA120A, static pressure cannot be measured. The display is always 0 MPa, but this is not a measured value.
*2: When Optional code /F1 is specified, substitute the value with 0.1.
*3: When Optional code /F1 is specified, substitute the value –5 with –2.5.
*4: Not applicable for Model EJA115.
*5: Applicable only for Model EJA118W, EJA118N, EJA118Y, EJA438W, and EJA438N.
*6: See MWP(max. working pressure) on the nameplate. B40 shows an approximate value of maximum pressure for the capsule.
*7: Unless otherwise specified by order. When optional code /F1 is specified, substitute the value –5 with –2.5.
IM 01C21F01-01E
8.3.2 Parameter Usage and Selection
IMPORTANT
Before describing the procedure for setting
parameters, we present the following table showing If the transmitter is turned off within 30 seconds
how the parameters are used and in what case. after parameters have been set, the set data
will not be stored and the terminal returns to
previous settings.
Table 8.1 Parameter Usage and Selection

Setup Item Description
Tag No. setup Sets the Tag No. (using 16 alphanumeric characters).
P. 8-9 Note: Up to 8 alphanumerics (upper case letters) can be used in the BT100.
Calibration range setup Sets the calibration range for 4 to 20 mA DC. Sets three data items: range unit, input
P. 8-9 value at 4 mA DC (LRV), and input value at 20 mA DC (HRV).
Note: LRV and HRV can be specified with range value specifications up to 5 digits (excluding any
decimal point) within the range of –32000 to 32000.
Damping time constant setup Adjusts the output response speed for 4 to 20 mA DC.
P. 8-10 Can be set in 9 increments from 0.2 to 64 s.
Output signal low cut mode Used mainly to stabilize output near 0% if output signal is the square root mode.
setup Two modes are available: forcing output to 0% for input below a specific value, or
P. 8-11 changing to proportional output for input below a specific value.
Change the output limits Change the range of normal output.
P. 8-11
Integral indicator scale range Sets the following 5 types of integral indicator scale ranges and units:
and unit setup % scale indicator, user set scale indicator, alternate indication of user set scale and
P. 8-11 % scale, input pressure display, alternate indication of input pressure and % scale
When using the user set scale, 4 types of data can be set:
user set scale setting, unit (BT200 only), display value at 4 mA DC (LRV), and
display value at 20 mA DC (HRV).
Note: LRV and HRV can be specified with range value specifications up to 5 digits
(excluding any decimal point) within the range of –19999 to 19999.
Unit setup for displayed Sets a unit for temperatures displayed on the BT200.
temperature
P. 8-13
Operation mode (normal/ Reverses the direction for 4 to 20 mA DC output relative to input.
reverse signal) setup Reverse mode is used for applications in which safety requires that output be driven
P. 8-13 toward 20 mA if input is lost.
Output status display/setup Displays the status of 4 to 20 mA DC output when a CPU failure. The parameter of the
when a CPU failure standard unit is fixed to the high limit value.
P. 8-13
Output status setup when a Sets the status of the 4 to 20 mA DC output when an abnormal status is detected
hardware error occurs with the capsule or the amplifier as the result of self-diagnosis. One of the following
P. 8-13 statuses; last held, high limit, and low limit values, can be selected.
Range change (while applying Range for 4 to 20 mA DC signal is set with actual input applied. Sets 20 mA DC output
actual inputs) precisely with respect to user’s reference instrument output. Note that DPharp is
P. 8-14 calibrated with high accuracy before shipment, so span should be set using the normal
range setup.
Zero point adjustment Adjusts zero point. This can be done either using the external zero-adjustment screw
P. 8-14 on the transmitteror using the BT200.
Span adjustment Adjust the characterization curve. All the transmitters are calibrated at factory and this
P. 8-16 adjustment is normally not necessary for most cases. Use for specific purposes.
Test output (fixed current output) Used for loop checks.
setup Output can be set freely from –5% to 110% in 1% steps.
P. 8-17
User memo fields Allows user to enter up to 5 items of any desired text in up to 8 uppercase alphanumeric
P. 8-17 characters per item.
IM 01C21F01-01E
8.3.3 Setting Parameters SET Set TAG NO. and press the
C10:TAG NO.
Set or change the parameters as necessary. After YOKOGAWA key.
FIC-1a _
completing these, do not fail to use the “DIAG” key
to confirm that “GOOD” is displayed for the self- CODE caps CLE ESC
diagnostic result at _60: SELF CHECK.

When you have made an entry mistake, return
the cursor using the key, then reenter.
(1) Tag No. Setup
(C10: TAG NO) SET This is the panel for confirming
C10:TAG NO.
YOKOGAWA set data. The set data items flash.
Use the procedure below to change the Tag No. Up FIC-1a
When all items have been
to 16 alphanumeric characters can be entered. PRINTER OFF
F2:PRINTER ON
FEED POFF NO
confirmed, press the
again. (To go back to the setting
• Example: Set a Tag No. to FIC-1a panel, press the (NO) key.
Press the key to turn on SET The DPharp TAG NO. was
the BT200. C10:TAG NO.
FIC-1a overwritten.
<When power is off>
Press the (OK) key to
FEED NO OK
return to the parameter panel.
--WELCOME-- Connect DPharp and BT200 Press the (NO) key to
BRAIN TERMINAL PARAM
ID: BT200 using a communication cable and C10:TAG NO.
FIC-1a
return to the setting panel.
check connection press the key. C20:PRESS UNIT
kPa
push ENTER key
C21:LOW RANGE
0 kPa
UTIL FEED
DATA DIAG PRNT ESC
PARAM Displays the name of connected
01:MODEL F0812-2.ai
EJA110A-DM DPharp model, TAG NO. and
02:TAG NO.
YOKOGAWA diagnostics information. Press the
03:SELF CHECK
GOOD (OK) key after confirmation. (2) Calibration Range Setup
OK
a. Setting Calibration Range Unit
MENU Press the (SET) key to
A:DISPLAY
B:SENSOR TYPE display the SET menu panel. (C20: PRESS UNIT)
The unit is set at the factory before shipment if
HOME SET ADJ ESC specified at the time of order. Follow the procedure
MENU Select C: SETTING and press the below to change the unit.
C:SETTING
D:AUX SET 1 key.
E:AUX SET 2
H:AUTO SET • Example: Change the unit from mmH2O to
HOME SET ADJ ESC
kPa.
MENU Select C10: TAG NO. and press SET Use the or
C10:TAG NO. C20:PRESS UNIT
YOKOGAWA the key. mmH20
key to select “kPa.”
C20:PRESS UNIT < mmWG >
kPa < mmHG >
C21:LOW RANGE < Torr > Press the key twice
0 kPa < kPa >
DATA DIAG PRNT ESC ESC to enter the setting.
SET Set the new TAG NO. (FIC-1a). SET
C10:TAG NO. C20:PRESS UNIT Press the (OK) key.
YOKOGAWA FOKOGAWA kPa
YOKOGAWA
FIKOGAWA
CODE CAPS CLR ESC FICOGAWA
FEED NO OK
FIC-GAWA
mmH2O
FIC-1AWA
mmAq
FIC-1aWA mmWG
mmHg
FIC-1a Torr
Pa
F0812-1.ai hPa
kPa
MPa
mbar
bar
gf/cm2
kgf/cm2
inH2O
inHg
ftH2O
psi
atm
F0813.ai
IM 01C21F01-01E
b. Setting Calibration Range Lower Range
Value and Higher Range Value • Example 2: With present settings of 0 to
(C21: LOW RANGE, C22: HIGH RANGE) 30 kPa, set the Higher range
value to10 kPa.
These range values are set as specified in the
order before the instrument is shipped. Follow the
SET
C22:HIGH RANGE
Set 10.
30 kPa Press the key twice
procedure below to change the range. + 10
to enter the setting.
• The measurement span is determined by DEL CLR ESC
the high and low range limit values. In this
SET Press the (OK) key.
instrument, changing the low range value also C22:HIGH RANGE
10 kPa
automatically changes the high range value,
keeping the span constant.
FEED NO OK
• Example 1: With present settings of 0 to PARAM

C20:PRESS UNIT
The low range value is not
30 kPa, set the lower range value kPa changed, so the span changes.
C21:LOW RANGE
0 kPa
to 0.5 kPa. C22:HIGH RANGE
10 kPa
DATA DIAG PRNT ESC
SET
C21:LOW RANGE
Set 0.5.
0 kPa Press the key twice to F0815.ai
+ 0.5
enter the setting.
(3) Damping Time Constant Setup
DEL CLR ESC
(C30: AMP DAMPING)
SET
Press the (OK) key.
C21:LOW RANGE
0.5 kPa When the instrument is shipped, the damping time
constant is set at 2.0 seconds. Follow the procedure
below to change the time constant.
FEED NO OK
SET
C20:PRESS UNIT
The higher range value is • Example: Change from 2.0 sec to 4.0 sec.
kPa
C21:LOW RANGE changed while the span remains
SET
0.5 kPa
constant. C30:AMP DAMPING Use the or
C22:HIGH RANGE
2.0 sec
30.5 kPa
DATA DIAG PRNT ESC < 2.0 sec > key to select 4.0 sec.
< 4.0 sec >
< 8.0 sec > Press the key twice
(Span = Higher range value – Lower range value ) < 16.0 sec >
ESC to enter the setting.
F0814.ai
SET
C30:AMP DAMPING Press the (OK) key.
• Note, however, that changing the higher range 4.0 sec
value does not cause the lower range value to

change. Thus, changing the higher range value FEED NO OK
also changes the span.
0.2sec
• Calibration range can be specified with range 0.5sec
value specifications up to 5 digits (excluding 1.0sec
2.0sec
any decimal point) for low or high range limits
within the range of −32000 to 32000. 4.0sec
8.0sec
16.0sec
32.0sec
64.0sec
F0816.ai
Note: The damping time constant set here is the damping time
constant for the amplifier assembly. The damping time
constant for the entire transmitter is the sum of the values
for the amplifier assembly and for the capsule assembly.
For the capsule assembly damping time constant (fixed),
see the “General Specifications” found at the end of this
manual. (See Chapter 10.)
IM 01C21F01-01E
(4) Output Signal Low Cut Mode Setup (5) Change Output Limits
(D10: LOW CUT, D11: LOW CUT MODE) (D15: OUT LIMIT(L), D16: OUT LIMIT(H))
Low cut mode can be used to stabilize the output The range of normal output is preset at factory from
signal near the zero point. The low cut point can be -5.0 to 110.0% unless otherwise specified, and the
set in a range from 0 to 20% of output. (Hysteresis output is limited with these upper and lower values.
of cut point: ±1%) This output range can be changed, for example, to
meet the requirements of NAMUR, etc. within the
 LOW CUT at 10%
settable range. Set the lower limit with D15: OUT
50 LIMIT(L) and upper limit with D16: OUT LIMIT(H).
Settable range: −5.0 to 110.0 (%)
Output(%)
Lower limit < Upper limit
10 (6) Integral Indicator Scale Setup

0 10 50 The following 5 displays are available for integral
Input(%)
F0817.ai indicators.
D20: DISP SELECT Description

• Example: Change the low cut setting range and Display and Related parameters
from 5% to 10%, and the low NORMAL % Indicates –5 to 110% range
cut mode from LINEAR to ZERO. depending on the Measurement
range (C21, C22).
SET Set “10.”
D10:LOW CUT A10:OUTPUT (%)
5.0 %
+ 10.0 Press the key twice to 45.6 %
enter the setting. USER SET Indicates values depending on the
CLR ESC
Engineering range (D22, D23).(Note 1)
Units set using Engineering unit
D10:LOW CUT (D21) are not indicated.
10.0 %
Next, the [D11: LOW CUT MODE]
A11:ENGR.OUTPUT
setting panel is displayed. 20.0 M
FEED NO OK
USER & % Indicates user set and % alternately
SET Use the or key in 3 second intervals.
D11:LOW CUT MODE
LINEAR
< LINEAR > to select ZERO. A10:OUTPUT (%)
< ZERO >
Press the key twice to 45.6 %
ESC A11:ENGR. OUTPUT
enter the setting.
20.0 M
SET
D11:LOW CUT MODE
Press the (OK) key.
ZERO
INP PRES Indicates input pressure.(Note 2)
Indication limits –19999 to 19999.
A40:INPUT
FEED NO OK
456 kPa
PARAM
D10:LOW CUT
PRES & % Indicates input pressure and %
10.0 % alternately in 3 second intervals.
D11:LOW CUT MODE
ZERO
D20:DISP SELECT A10:OUTPUT (%)
NORMAL %
DATA DIAG PRNT ESC 45.6 %
A40:INPUT
F0818.ai 456 kPa
F0819.ai
Note 1: Scale range can be specified with range limit

specifications up to 5 digits (excluding any decimal
point) for low or high range limits within the range of
–19999 to 19999.
The range with decimals is available to the third
decimal place.
Note 2: It indicates the value after zeroing.
IM 01C21F01-01E
See (a.) through (c.) for each setting procedure. a. Display Selection (D20: DISP SELECT)
Follow the instructions given to the below to change
% indication and User-set engineering
the range of integral indication scales.
input pressure unit display
indication When USER SET is selected, the user set values
of integral indication and A11: ENGR. OUTPUT
D20: DISP SELECT D20: DISP SELECT
NORMAL % USER SET
parameter are indicated.
INP PRES USER & %
PRES & % • Example: Set the integral indicator scale to
engineering units display.
Set for user-set
engineering unit display. SET Use the or key
D20:DISP SELECT
NORMAL %
<NORMAL %> to select “USER SET.”
<USER SET>
Transmitter is set D21: DISP UNIT <USER & %> Press the key twice to
<INP PRES>
ESC enter the setting.
for “% display” when Set a unit to be
shipped. displayed on the BT200. SET
D20:DISP SELECT Press the (OK) key.
USER SET
For % display, set this D22: DISP LRV

FEED NO OK
parameter only. Set a numeric value for
engineering unit for 4 mA
output (LRV).
The “%” disappears from the
integral indicator display.
F0821.ai
D23: DISP HRV
Set a numeric value for b. Setting User-set Engineering Unit
engineering unit for 20 mA (D21: DISP UNIT)
output (HRV).
F0820.ai This parameter allows entry of the engineering units
to be displayed on the BT200. When the instrument
is shipped, this is set as specified in the order.
Follow the procedure below to change this setting.
This parameter need not be set for % display.
• Example: Set an engineering unit M.

SET Set “M.”
D21:DISP UNIT
M_ Press the key twice to
enter the setting.
CODE CAPS CLR ESC

D21:DISP UNIT
M
FEED NO OK
F0822.ai
IM 01C21F01-01E
c. Lower and Higher Range Value Setup in (8) Operation Mode Setup
Engineering Unit (D40: REV OUTPUT)
(D22: DISP LRV, D23: DISP HRV)
This parameter allows the direction of the 4 to 20
These parameter items are used to set the lower mA output to be reversed with respect to input.
and higher range values for the engineering unit Follow the procedure below to make this change.
display.
• Example: Change 4 to 20 mA output to 20 to
When the instrument is shipped, these are set
4 mA output.
as specified in the order. Follow the procedure
below to change these settings. Note that these SET
D40:REV OUTPUT
Use the or key
NORMAL
parameters need not be set for % display. < NORMAL > to select REVERSE.
< REVERSE>
Press the key twice to
• Example: Set lower range value (LRV) to –50 ESC
enter the setting.
and higher range value (HRV) to 50.
F0825.ai
Setting LRV
SET
D22:DISP LRV
Set “–50.” (9) Output Status Display/Setup when a CPU
-
0M
50 Press the key twice to Failure
enter the setting. (D52: BURN OUT)
DEL CLR ESC
This parameter displays the status of 4 to 20 mA
Setting HRV DC output if a CPU failure occurs. In case of a
SET Set “50.” failure, communication is disabled.
D23:DISP HRV
100M
+ 50 Press the key twice to
Setting of HIGH or LOW is enabled. This is done
enter the setting.
DEL CLR ESC
with the pin (CN4) on the CPU assembly. See
Chapter 3 for details.
SET Press the (OK) key. Standard specifications
D23:DISP HRV
50M
The parameter is set to HIGH. If a failure, the
transmitter outputs the signal of 110% or higher.
FEED NO OK
The parameter D53: ERROR OUT is set to HIGH
PARAM from the factory.
D21:DISP UNT
M
D22:DISP
-
LRV
50M
Optional code/C1
D23:DISP HRV
DATA
50M
DIAG PRNT ESC The parameter is set to LOW. If a failure, output
which is −5% or lower is generated. The parameter
F0823.ai
D53: ERROR OUT is set to LOW from the factory.
(7) Unit Setup for Displayed Temperature
(D30: TEMP UNIT) • Example: Standard specifications
D52: BURN OUT pin (CN4) position: H
When the instrument is shipped, the temperature HIGH
units are set to degC. Follow the procedure below

to change this setting. Note that changing the • Example: Optional code/C1
unit here changes the unit for A20: AMP TEMP D52: BURN OUT pin (CN4) position: L
(amplifier temperature) and A21: CAPSULE TEMP LOW
(capsule temperature). F0826.ai
• Example: Change the unit for the temperature (10) Output Status Setup when a Hardware
display. Error Occurs
(D53: ERROR OUT)
SET
D30:TEMP UNIT
Use the or key
deg C
< deg C > to select “deg F.” This parameter allows the setting of the output
< deg F >
Press the key twice to status when a hardware error occurs. The following
ESC
enter the setting. three selections are available.
F0824.ai
IM 01C21F01-01E
(a) HOLD; Outputs the last value held before the Note that changing the higher range value does not
error occurred. cause the lower range value to change but does
(b) HIGH; Outputs an output of 110% when an change the span.
error has occurred.
(c) LOW; Outputs an output of −5% when an error • Example 2: When the higher range value is to
has occurred. be changed to 10 kPa with the
Note: A hardware error means CAP MODULE FAULT of Er.01 present setting of 0 to 30 kPa, take
or AMP MODULE FAULT of Er. 02 which are shown in
8.5.2 “Errors and Countermeasures.”) the following action with an input
pressure of 10 kPa applied.
• Example: Set the output status to LOW when SET Press the key twice.
H11:AUTO HRV
a hardware error occurs. +
30 kPa
30 The higher range value is
SET
D53:ERROR OUT Use the or key changed to 10 kPa.
HIGH ESC
< HIGH> to select “LOW.”
< LOW>
< HOLD>
Press the key twice to
SET
H11:AUTO HRV
Press the (OK) key.
ESC 10.000 kPa
enter the setting.
F0827.ai
FEED NO OK
(11) Range Change while Applying Actual PARAM

H10:AUTO LRV
The lower range value is not
Inputs 0 kPa
H11:AUTO HRV changed, so the span changes.
10.000 kPa
(H10: AUTO LRV, H11: AUTO HRV) H60:SELF CHECK Parameter C22 is changed at the
GOOD
DATA DIAG PRNT ESC
This feature allows the lower and higher range same time.
values to be set up automatically with the actual F0829.ai
input applied. If the lower and higher range values

are set, C21: LOW RANGE and C22: HIGH (12) Zero Point Adjustment
RANGE are changed at this same time. (J10: ZERO ADJ, J11: ZERO DEV, J20: EXT
ZERO ADJ)
Follow the procedure in the figure below.
The measurement span is determined by the higher The DPharp supports several adjustment methods.
and lower range values. Changing the lower range Select the method best suited for the conditions of
value results in the higher range value changing your application.
auto-matically, keeping the span constant. Note that output signal can be checked by
displaying parameter A10:OUTPUT (%) on the
• Example 1: When changing the lower range
BT200.
value to 0.5 kPa for the present
setting of 0 to 30 kPa, take the Adjustment
Description
following action with input pressure Method
Using the Set the present input to 0%.
of 0.5 kPa applied.
BT200 Adjust for 0% output at input level of
0%.
SET Press the key twice.
H10:AUTO LRV Adjust output to the reference value
0 kPa
+ 0 The lower range value is obtained using other means.
changed to 0.5 kPa.
If the input level cannot easily be
ESC
made 0% (because of tank level, etc.),
adjust output to the reference value
SET
H10:AUTO LRV
Press the (OK) key. obtained using other means, such as
0.5000 kPa a sight glass.
Using the Adjust zero point using the zero-
external adjustment screw on the transmitter.
FEED NO OK
zero- This permits zero adjustment without
PARAM The higher range value is adjustment using the BT200. Accurately adjust the
H10:AUTO LRV
0.5000 kPa screw output current to 4 mA DC or other target
H11:AUTO HRV changed keeping the span P.8-14 output value using an ammeter that
30.500 kPa
H60:SELF CHEC
GOOD
constant. accuratly reads output currents.
DATA DIAG PRNT ESC
Parameters C21 and C22 are
changed at the same time.
F0828.ai
IM 01C21F01-01E
(a) Follow the procedure below when setting the (b)-2 Follow the procedure below to use J11:
present output to 0% (4 mA). ZERO DEV.
A10:OUTPUT (%)
Present output is 41.0%.
A10:OUTPUT (%) Output is 0.5%. 41.0 %
0.5 % Output error = 40.0–41.0 = –1.0%.
SET
SET
J11:ZERO DEV.
Since “J11: ZERO DEV.” contains
J10:ZERO ADJ Press the key twice. 2.50 %
0.0 % 0 the previous correction, obtain the
+ 000.0
correction value by adding –1.0%
ESC
CLR ESC to it. 2.50% + (–1.0%) = 1.50%
SET
J10:ZERO ADJ Zero adjustment is completed. SET
J11:ZERO DEV.
Set the correction value, 1.50.
0.0 % 2.50 %
Press the (OK) key. 1.50 Press the key twice.
FEED NO OK ECS
A10:OUTPUT (%) Output is 0%. A10:OUTPUT (%) The output is changed to 40%.
0.0 % 40.0 %
F0832.ai
F0830.ai
When the zero point is adjusted, the displayed

(b) In tank level measurement, if the actual level
value of A40 is as follows.
cannot be brought to zero for zero adjustment,
then the output can be adjusted to correspond
[Example]
to the actual level obtained using another
measuring instrument such as a glass gauge. When the zero point is shifted by 20 kPa for the
actual pressure, the parameter of A40 indicates 50
[Example]
kPa.
Measurement range: 50 to 250 kPa, Actual value:
130 kPa.
70 kPa
Actual value
– Measurement range lower range value 50 kPa
Actual =
x 100
value(%) Measurement range higher range value
– Measurement range lower range value Zero
20 kPa adjustment
Zero adjustment
130–50 volume(J11)
= x 100 = 40.0% 0 kPa 0 kPa
250–50 Actual differential Input value
pressure/pressure of A40
F0833.ai
(b)-1 Follow the procedure below to use J10:
ZERO ADJ. (c) Zero Point Adjustment Using the External Zero
Adjustment Screw
A10:OUTPUT (%)
Present output is 41.0%. • Enabling/inhibiting of zero point adjustment
41.0 %
using the external zero-adjustment screw on
the transmitter (J20: EXT ZERO ADJ)
SET
J10:ZERO ADJ
Enter the present actual level,
0.0 %
+ 040.0 40%. Follow the procedure below to enable or inhibit zero
Press the key twice. point adjustment from the zero-adjustment screw
CLR ESC on the transmitter.
A10:OUTPUT (%) The output is changed to 40%. This is set to “ENABLE” when the instrument is
40.0 %
shipped.
F0831.ai
IM 01C21F01-01E
• Span adjustment value
• Example: Inhibiting zero adjustment by the
The span adjustment value is calculated as
external zero-adjustment screw
follows.
SET Use the or key P – A40 ×100
J20:EXIT ZERO ADJ Span adjustment value (%) = 1
ENABLE
< ENABLE > to select “INHIBIT.” P1
< INHIBIT>
Press the key twice to P1: Actual differential pressure/pressure value
ESC
enter the setting. A40: Input (indicated as the value after zeroing)
F0834.ai
Measurement pressure
• Zero point adjustment using external zero-
adjustment screw on the transmitter
A40
Turn the zero-adjustment screw on the outside of
the transmitter case using a slotted screwdriver.
Turn the screw to the right to increase the zero point Applied pressure
P1
or to the left to decrease the zero output; the zero 0
F0835.ai
adjusts in increments of 0.01% of the range setting.
Note that the amount of adjustment to the zero point • Example: For the range of 0 to 30 kPa.
changes according to the speed at which the screw A40: INPUT = 30.15 kPa
is turned. To make fine adjustments, turn the screw J15: SPAN ADJ = 0.15 %
slowly; to make coarse adjustments, turn the screw
Suppose that a standard pressure of 30 kPa is applied
quickly. and the value of the parameter of A40:INPUT is 30.15 kPa.
Note: When a zero point adjustment has been made, do not turn Firstly, obtain the slope error for the span as follows;
off the transmitter less than 30 seconds after adjustment.
P1 – A40
Span adjustment value (%) = ×100
(13) Span Adjustment P1
30.00 – 30.15
Each DPharp EJA series transmitter is factory = ×100 = −0.5 (%)
30.00
characterized according to the specification.
Mounting position effects or zero shifts caused by Add −0.5% to 0.15% of the current value to calculate the
static pressure are typically compensated by a zero accumulated span adjustment value.
adjustment. 0.15 + (−0.50) = –0.35
A span adjustment is a function to correct the slope

SET Set −0.35.
error from a zero point in characterizing 100% point J15:SPAN ADJ
0.15 %
(HRV). This function can be used when span drifts - 0.35 Press key twice.
may be caused or characterization to the specific
DEL CLR ESC
pressure standard is required.
Therefore, the zero point adjustment should always J15:SPAN ADJ
-0.35 %
be performed before the upper point adjustment in
order to maintain the pitch between zero and 100%
FEED NO OK
points within the calibration range.
You can manually perform the trimming procedure Note: Enter 0.00 to J15: SPAN ADJ to reset the
by using J15: SPAN ADJ. span adjustment to the initial value at the
shipment.
F0836.ai
IM 01C21F01-01E
(14) Test Output Setup 8.4 Displaying Data Using the
(K10: OUTPUT X%)
BT200
This feature can be used to output a fixed current
from 3.2 mA (−5%) to 21.6 mA (110%) for loop 8.4.1 Displaying Measured Data
checks.
The BT200 can be used to display measured data.
• Example: Output 12 mA (50%) fixed current. The measured data is updated automatically every
7 seconds. In addition, the display can be updated
SET
K10:OUTPUT X %
Set “50.0%.” to the present data value at any time by pressing
0.0 %
+ 050.0 Press the key twice to the [F1] (DATA) key. For parameters associated
output a fixed current at 50%. with the display of measured data, see Subsection
ESC
8.3.1, “Parameter Summary.”
SET “Active” is displayed while this is
K10:OUTPUT X %
50.0 % ACTIVE
being executed. • Example: Display output.
Press the (OK) key to cancel MENU
A:DISPLAY
FEED NO OK
the fixed current output. B:SENSOR TYPE
F0837.ai
HOME SET ADJ ESC
IMPORTANT PARAM
A10:OUTPUT (%)
Display “A10: OUTPUT (%).”
XX.X %
A11:ENGR.OUTPUT
1. Test output is held for approximately 10 YY.Y %
A20:AMP TEMP
minutes, and then released automatically ZZ deg C
DATA DIAG PRNT ESC
after the time has elapsed. Even if the Data is updated automatically
at 7-second intervals.
BT200 power supply is turned off or the PARAM
A10:OUTPUT (%)
communi
communication cable is disconnected during A11:ENGR.OUTPUT
test output, it is held for approximately 10 A20:AMP TEMP
minutes.
2. Press the [F4] (OK) key to release test output
F0839.ai
immediately.
8.4.2 Display Transmitter Model and
(15) User Memo Fields Specifications
(M: MEMO) The BT200 can be used to display the model and
This feature provides 5 user memo fields, each specifications of the transmitter.
holding up to 8 alphanumeric characters. Up to 5
items such as inspection date, inspector, and other • Example: View transmitter model name.
information can be saved in these fields. MENU Press .
A:DISPLAY
B:SENSOR TYPE
• Example: Save an inspection date of January
30, 1995.
HOME SET ADJ ESC
PARAM
M10:MEMO 1
Set “95.1.30” in the order of year,
M20:MEMO 2 month, and day.
M30:MEMO 3 Press the key twice to
PARAM
DATA DIAG PRNT ESC
enter the setting. B10:MODEL For the associated
SET
EJA510A-DC parameters, see
B11:STYLE NO.
M10:MEMO 1
S1.01 Subsection 8.3.1,
95.1.30_ B20:LRL Parameter Summary.
- 98.07 kPa
DATA DIAG PRNT ESC
ESC
F0840.ai
F0838.ai
IM 01C21F01-01E
8.5 Self-Diagnostics • Example 3: Checking the history of the errors
8.5.1 Checking for Problems MENU
J:ADJUST
Connect the BT200 to the
K:TEST
M:MEMO
transmitter, and call item “P.”
(1) Identifying Problems with BT200 P:RECORD
The following four areas can be checked. HOME SET ADJ ESC
PARAM
(a) Whether connections are good. P10:ERROR REC 1
ERROR
(b) Whether BT200 was properly operated. P11:ERROR REC 2
ERROR
(c) Whether settings were properly entered. P12:ERROR REC 3
GOOD
DATA DIAG PRNT ESC
(d) History of the errors.
See examples below. P10: “ERROR REC 1” displays the last error.
P11: “ERROR REC 2” displays the error one time before
• Example 1: Connection errors the last error occurred.
P12: “ERROR REC 3” displays the error two times before
--WELCOME-- Press the key.
BRAIN TERMINAL
ID: BT200
the last error occurred.
When the panel shown on the left P13: “ERROR REC 4” displays the error three times
check connection
push ENTER key appears, press the key. before the last error occurred.
UTIL FEED
The history of up to four errors can be stored. When the
Since communications will be 5th error has occurred, it is stored in “P10”. The error
communication error unsuccessful if there is a problem stored in “P13” will be deleted, and then, the error in “P12”
in the connection to the BT200, will be copied to “P13”. In this sequence, the history of the
ESC the display at the left will appear. most previously occurred error will be removed from
memory.
Recheck the connection.
“GOOD” will be displayed if there was no previous error.
Press the (OK) key.
F0841.ai
SET Select P10: ERROR REC1 and
P10:ERROR REC 1
<
ERROR
ERROR >
press the key to
< ILLEGAL LRV > display the error message.
< ILLEGAL HRV >
ESC
• Example 2: Setting entry errors
<(a) SETUP PANEL>
PARAM The initial data panel shows the
01:MODEL
EJA510A-DC For the details of the messages listed below, see Table
02:TAG NO. result of current transmitter
YOKOGAWA 8.5.1 Error Message Summary.
03:SELF CHECK diagnostics.
ERROR
OK CAP MODULE FAULT OVER TEMP (CAP) ILLEGAL LRV
AMP MODULE FAULT OVER TEMP (AMP) ILLEGAL HRV
PARAM
C20:PRESS UNIT
Press the (DIAG) key in the
kPa OUT OF RANGE OVER OUTPUT ILLEGAL SPAN
C21:LOW RANGE parameter panel to go to the
600 kPa OUT OF SP RANGE OVER DISPLAY ZERO ADJ OVER
C22:HIGH RANGE
600 kPa
diagnostics panel
DATA DIAG PRNT ESC
(C60: SELF CHECK). Note 1: Press the key twice in the setting panel
DIAG An error message is displayed (panel 1) to clear all error message (P10 to P13)
C60:SELF CHECK
ERROR information.
< ERROR > when an error occurs in the
< ILLEGAL LRV > Note 2: After two hours from when an error occurs, the
diagnostics panel.
error message of that error will be recorded.
FEED PRNT ESC
Therefore, if you switch off the transmitter within
F0842.ai two hours from when the error occurs, there is no
history of that error stored in the transmitter, and
this function is meaningless.
F0843.ai
IM 01C21F01-01E
(2) Checking with Integral Indicator
NOTE
If an error is detected in the self-diagnostic,
an error number is displayed on the integral
indicator. If there is more than one error, the error
number changes at two-second intervals. See
Table 8.2 regarding the error numbers.
F0844.ai
Figure 8.5 Identifying Problems Using the Integral

Indicator
IM 01C21F01-01E
8.5.2 Errors and Countermeasures
The table below shows a summary of error messages.
Table 8.2 Error Message Summary
Integral
Output Operation during
Indicator BT200 Display Cause Countermeasure
Error
Display
None GOOD
--- ERROR
Er.01 CAP MODULE FAULT Capsule problem.*1 Outputs the signal (Hold, Replace the capsule when
High, or Low) set with error keeps appearing even
parameter D53. after restart.*2
Er.02 AMP MODULE FAULT Amplifier problem. Outputs the signal (Hold, Replace amplifier.
High, or Low) set with
parameter D53.
Er.03 OUT OF RANGE Input is outside Outputs high range limit Check input.
measurement range value or low range limit
limit of capsule. value.
Er.04 OUT OF SP RANGE Static pressure exceeds Displays present output. Check line pressure (static
specified range.*3 pressure).
Er.05 OVER TEMP (CAP) Capsule temperature is Displays present output. Use heat insulation or make
outside range lagging to keep temperature
(–50 to 130°C). within range.
Er.06 OVER TEMP (AMP) Amplifier temperature is Displays present output. Use heat insulation or make
outside range lagging to keep temperature
(–50 to 95°C). within range.
Er.07 OVER OUTPUT Output is outside high or Outputs high or low range Check input and range
low range limit value. limit value. setting, and change them as
needed.
Er.08 OVER DISPLAY Displayed value is Displays high or low range Check input and display
outside high or low limit value. conditions and modify them
range limit value. as needed.
Er.09 ILLEGAL LRV LRV is outside setting Holds output immediately Check LRV and modify as
range. before error occurrence. needed.
Er.10 ILLEGAL HRV HRV is outside setting Holds output immediately Check HRV and modify as
Er.11 ILLEGAL SPAN SPAN is outside setting Holds output immediately Check SPAN and change as
Er.12 ZERO ADJ OVER Zero adjustment is too Displays present output. Readjust zero point
large.
*1: This error code appears at a capsule problem or when an illegal overpressure is applied to the pressure sensor.
*2: If the normal pressure is regained, the Er.01 will disappear according to the setting of the parameter of E50: AUTO RECOVER.
When the E50: AUTO RECOVER is set to ON(defalut setting), the Er.01 will disappear automatically. When the E50: AUTO
RECOVER is set to OFF, restart the transmitter to cancel Er.01. If no error code appears then, perform necessary adjustment such
as zero-adjustment to continue the operation. If the error code still exists, replace the capsule assembly.
*3: For Model EJA120A, static pressure cannot be measured. The display is always 0 MPa, but this is not a measured value.
IM 01C21F01-01E
<9. Maintenance> 9-1
9. Maintenance
9.1 Overview 9.2 Calibration Instruments
Selection
WARNING Table 9.1 shows the instruments required for
Since the accumulated process fluid may be calibration. Select instruments that will enable
toxic or otherwise harmful, take appropriate care the transmitter to be calibrated or adjusted to the
to avoid contact with the body, or inhalation of required accuracy. The calibration instruments
vapors even after dismounting the instrument should be handled carefully so as to maintain the
from the process line for maintenance. specified accuracy.
Maintenance of the transmitter is easy due to its 9.3 Calibration

modular construction. This chapter describes the
Use the procedure below to check instrument
procedures for calibration, adjustment, and the
operation and accuracy during periodic
disassembly and reassembly procedures required
maintenance or troubleshooting.
for component replacement.
1) Connect the instruments as shown in Figure 9.1
Since the transmitters are precision instruments,
and warm up the instruments for at least five
carefully and thoroughly read the following sections
minutes.
for proper handling during maintenance.
IMPORTANT
IMPORTANT
• To adjust the transmitter for highest
• As a rule, maintenance of this transmitter accuracy, make adjustments with the
should be implemented in a maintenance power supply voltage and load resistance
service shop where the necessary tools are including leadwire resistances set close to
provided. the conditions under which the transmitter is
• The CPU assembly contains sensitive parts installed.
that may be damaged by static electricity. • If the measurement range 0% point is
Exercise care so as not to directly touch 0 kPa or shifted in the positive direction
the electronic parts or circuit patterns on (suppressed zero), the reference pressure
the board, for example, by preventing static should be applied as shown in the figure.
electrification by using grounded wrist straps If the measurement range 0% point is shifted
when handling the assembly. Also take in the negative direction (elevated zero), the
precautions such as placing a removed reference pressure should be applied using
CPU assembly into a bag with an antistatic a vacuum pump.
coating. • Do not perform the calibration procedure
until the transmitter is at room temperature.
2) Apply reference pressures of 0%, 50%,

and 100% of the measurement range to the
transmitter. Calculate the errors (differences
between digital voltmeter readings and
reference pressures) as the pressure is
increased from 0% to 100% and is decreased
from 100% to 0%, and confirm that the errors
are within the required accuracy.
IM 01C21F01-01E
Table 9.1 Instruments Required for Calibration
Name Yokogawa-recommended Instrument Remarks
Power supply Model SDBT or SDBS distributor 4 to 20 mA DC signal
Load resistor Model 2792 standard resistor [250 Ω ±0.005%, 3 W]
Load adjustment resistor [100 Ω ±1%, 1 W]
Voltmeter Model 2501 A digital multimeter
Accuracy (10V DC range): ±(0.002% of rdg + 1 dgt)
Digital Model MT220 precision digital manometer Select a manometer having a
manometer 1) For 10 kPa class pressure range close to that of
Accuracy: ± (0.015% of rdg + 0.015% of F.S.) · · for 0 to 10 kPa the transmitter.
± (0.2% of rdg + 0.1% of F.S.) · · · · · · for −10 to 0 kPa
2) For 130 kPa class
Accuracy: ± 0.02% of rdg · · · · · · · · · · · · · · · · · · for 25 to 130 kPa
± 5 digits · · · · · · · · · · · · · · · · · · · · · · · for 0 to 25 kPa
Accuracy: ± (0.02% of rdg + 3 digits) · · · · · · · · · for 100 to 700 kPa
± 5 digits · · · · · · · · · · · · · · · · · · · · · · · for 0 to 100 kPa
Accuracy: ± (0.02% of rdg + 10 digits) · · · · · · · · for 0 to 3000 kPa
5) For 130 kPa abs class
Accuracy: ± (0.03% of rdg + 6 digits) · · · · · · · · · for 0 to 130 kPa abs
Pressure Model 7674 pneumatic pressure standard for 200 kPa {2 kgf/cm2}, Requires air pressure supply.
generator 25 kPa {2500 mmH2O}
Accuracy: ± 0.05% of F.S.
Dead weight gauge tester 25 kPa {2500 mmH2O} Select the one having a
Accuracy: ±0.03% of setting pressure range close to that of
the transmitter.
Pressure Model 6919 pressure regulator (pressure pump) Prepare the vacuum pump for
source Pressure range: 0 to 133 kPa {1000 mmHg} negative pressure ranges.
Note: The above table contains the instruments capable of performing calibration to the 0.2% level. Since special maintenance and
management procedures involving traceability of each instrument to higher-level standards are required for calibration to the 0.1%
level, there are difficulties in calibration to this level in the field. For calibration to the 0.1% level, contact Yokogawa representatives
from which the instrument was purchased or the nearest Yokogawa office.
If a pressure generator If a pressure source and

is used: a manometer are combined:
Load resistance, Power Load resistance, Power

250Ω supply 250Ω supply
E E
Load Rc R Load Rc R
adjustment adjustment
resistance, V resistance, V
100Ω Digital voltmeter 100Ω Digital voltmeter
Reference pressure Reference pressure
P Model 7674 pneumatic P
pressure standards
Model MT220
precision digital manometer
Supply pressure Pressure source

F0901.ai
Figure 9.1 Instrument Connections
IM 01C21F01-01E
9.4 Disassembly and 9.4.1 Replacing the Integral Indicator
Reassembly
CAUTION
CAUTION Cautions for Flameproof Type Transmitters
Users are prohibited by law from modifying the
Precautions for CENELEC and IECEx
construction of a flameproof type transmitter.
Flameproof Type Transmitters
This would invalidate the agency approval and
• Flameproof type transmitters must be, as
the transmitter’s use in such rated area.
a rule, removed to a non-hazardous area
Thus the user is prohibited from using a
for maintenance and be disassembled and
flameproof type transmitter with its integral
reassembled to the original state.
indicator removed, or from adding an integral
• On the flameproof type transmitters the two
indicator to a transmitter. If such modification is
covers are locked, each by an Allen head
absolutely required, contact Yokogawa.
bolt (shrouding bolt). When a shrouding bolt
is driven clockwise by an Allen wrench, it is
This subsection describes the procedure for
going in and cover lock is released, and then
replacing an integral indicator. (See Figure 9.4)
the cover can be opened by hand.
When a cover is closed it should be locked by a  Removing the Integral Indicator
shrouding bolt without fail. Tighten the shrouding
1) Remove the cover.
bolt to a torque of 0.7 N·m.
2) Supporting the integral indicator by hand,
loosen its two mounting screws.
This section describes procedures for disassembly
3) Dismount the LCD board assembly from the
and reassembly for maintenance and component
CPU assembly.
replacement.
When doing this, carefully pull the LCD board
Always turn OFF power and shut off and release assembly straight forward so as not to damage
pressures before disassembly. Use proper tools for the connector pins between it and the CPU
all operations. Table 9.2 shows the tools required. assembly.
Table 9.2 Tools for Disassembly and Reassembly  Attaching the Integral Indicator
Tool Quantity Remarks Integral indicator can be installed in the following
Phillips 1 JIS B4633, No. 2 three directions.
screwdriver
Slotted 1
screwdriver
Allen wrenches 2 JIS B4648
One each, nominal 3 and
5 mm Allen wrenches
Wrench 1 Width across flats, 17 mm
Torque wrench 1 F0903.ai
Adjustable 1 Figure 9.3 Installation Direction of Indicator
wrench
Socket wrench 1 Width across flats, 16 mm
1) Align both the LCD board assembly and CPU
Socket driver 1 Width across flats, 5.5 mm
assembly connectors and engage them.
Tweezers 1
2) Insert and tighten the two mounting screws.
3) Replace the cover.
Shrouding Bolt
Shrouding Bolt
F0902.ai
Figure 9.2 Shrouding Bolts
IM 01C21F01-01E
Output terminal cable  Mounting the CPU Assembly

1) Connect the flat cable (with black connector)
CPU assembly between the CPU assembly and the capsule.
Press Flat cable 2) Connect the output terminal cable (with brown
connector).
Boss
LCD board
assembly NOTE
Integral
indicator Make certain that the cables are free of pinching
between the case and the CPU assembly edge.
3) Align and engage the zero-adjustment screw

Bracket Zero-adjustment
(for zero-adjustment pin with the groove on the bracket on the CPU
screw pin
screw pin) assembly. Then insert the CPU board assembly
Cover straight onto the post in the amplifier case.
Mounting screw
4) Tighten the two bosses. If the transmitter is
F0904.ai
equipped with an integral indicator, refer to
Subsection 9.4.1 to mount the indicator.
Figure 9.4 Removing and Attaching LCD Board
Assembly and CPU Assembly
NOTE
9.4.2 Replacing the CPU Board Assembly Confirm that the zero-adjustment screw pin is
This subsection describes the procedure for placed properly in the groove on the bracket prior
replacing the CPU assembly. (See Figure 9.4) to tightening the two bosses. If it is not, the zero-
adjustment mechanism will be damaged.
 Removing the CPU Assembly
1) Remove the cover. If an integral indicator is 5) Replace the cover.
mounted, refer to Subsection 9.4.1 and remove
the indicator.
2) Turn the zero-adjustment screw to the position
(where the screw head slot is horizontal) as
shown in Figure 9.4.
3) Disconnect the output terminal cable (cable
with brown connector at the end). When doing
this, lightly press the side of the CPU assembly
connector and pull the cable connector to
disengage.
4) Use a socket driver (width across flats, 5.5mm)
to loosen the two bosses.
5) Carefully pull the CPU assembly straight
forward to remove it.
6) Disconnect the flat cable (cable with black
connector at the end) that connects the CPU
assembly and the capsule.
NOTE
Be careful not to apply excessive force to the
CPU assembly when removing it.
IM 01C21F01-01E
9.4.3 Cleaning and Replacing the Capsule 1) Remove the CPU assembly as shown in
Assembly Subsection 9.4.2.
2) Remove the two Allen screws and the pipe
This subsection describes the procedures for
(shown in Figure 9.5) for the model EJA530A
cleaning and replacing the capsule assembly. (See
with Measurement span code A, B, and C,
Figure 9.5.)
which connect the transmitter section and
capsule assembly.
CAUTION 3) Separate the transmitter section and capsule
assembly.
Cautions for Flameproof Type Transmitters 4) Clean the capsule assembly or replace with a
Users are prohibited by law from modifying the new one.
construction of a flameproof type transmitter. If
 Reassembling the Capsule Assembly
you wish to replace the capsule assembly with
one of a different measurement range, contact 1) Insert the capsule assembly to the transmitter
Yokogawa. section. For the model EJA530A with
The user is permitted, however, to replace a Measurement span code A, B, and C with the
capsule assembly with another of the same pipe (shown in Figure 9.5), insert the capsule
measurement range. When doing so, be sure to assembly in a way that the direction of the
observe the following. pipe screw thread matches to that of the zero-
• The replacement capsule assembly must adjustment screw of the transmitter section.
have the same part number as the one being 2) Tighten the two Allen screws to a torque of 5
replaced. N·m and the pipe with gasket if applied.
• The section connecting the transmitter and 3) Install the CPU assembly according to
capsule assembly is a critical element in Subsection 9.4.2.
preservation of flameproof performance, and 4) After completing reassembly, adjust the zero
must be checked to verify that it is free of point and check the parameters.
dents, scratches, and other defects. Transmitter section
• After completing maintenance, be sure to
securely tighten the Allen screws that fasten
the transmitter section and pressure-detector
section together.
Allen screw
Zero-adjustment
 Removing the Capsule Assembly screw
Allen screw
IMPORTANT
Gasket
Exercise care as follows when cleaning the
capsule assembly. Capsule name plate Pipe
• Handle the capsule assembly with care, and
be especially careful not to damage or distort
Pipe screw thread
the diaphragms that contact the process
Capsule assembly
fluid.
• Do not use a chlorinated or acidic solution for F0905.ai
cleaning. Figure 9.5 Removing and Mounting the Capsule

Assembly
• Rinse thoroughly with clean water and dry
thoroughly after cleaning.
IM 01C21F01-01E
9.5 Troubleshooting 9.5.2 Troubleshooting Flow Charts
If any abnormality appears in the measured values, Symptoms: • There is no output signal.
• Output signal does not change although
use the troubleshooting flow chart below to isolate process variable is known to be varying.
and remedy the problem. Since some problems • Output value is inconsistent with value
inferred for process variable.
have complex causes, these flow charts may not
identify all.
If you have difficulty isolating or correcting a Connect BRAIN TERMINAL and check self-diagnostics.
problem, contact Yokogawa service personnel.
9.5.1 Basic Troubleshooting

Does the self-diagnostic YES
First determine whether the process variable indicate problem location?
is actually abnormal or a problem exists in the

measurement system. NO Refer to error message summary in
Subsection 8.5.2 to take actions.
If the problem is in the measurement system,
isolate the problem and decide what corrective
action to take. Is power supply NO
polarity correct?
This transmitter is equipped with a self-diagnostic
function which will be useful in troubleshooting; see YES Refer to Section 6.3 to check/correct
Section 8.5 for information on using this function. polarity at each terminal from power
supply to the terminal box.
: Areas where self-diagnostic offers support

Are power
NO
supply voltage and load
Abnormalities appear in measurement. resistance correct?
YES Refer to Section 6.6 for rated voltage

and load resistance.
YES Is process variable
itself abnormal?
Are valves opened or NO

Inspect the NO closed correctly?
Measurement system problem
process system.
YES Fully close equalizing valve, and fully

open high pressure and low pressure
Isolate problem in
valves.
measurement system.
YES
Is there any pressure leak?
NO Fix pressure leaks, paying particular

YES Does problem exist in attention to connections for impulse
receiving instrument? piping,pressure-detector section, etc.
NO Is there
Inspect receiver. continuity through the NO
transmitter loop wiring?
Do the loop numbers
match?
Environmental conditions Transmitter itself
Find/correct broken conductor or
YES
wiring error.
Check/correct
Check transmitter.
environmental conditions. Contact Yokogawa service personnel.
Operating conditions F0907.ai
Check/correct operating
conditions.
F0906.ai
Figure 9.6 Basic Flow and Self-Diagnostics
IM 01C21F01-01E
Output travels beyond 0% or 100%. Large output error.
Connect BRAIN TERMINAL and check self-diagnostics. Connect BRAIN TERMINAL and check self-diagnostics.
Does the self- YES Does the self- YES

diagnostic indicate problem diagnostic indicate problem
location? location?
NO Refer to error message summary in NO Refer to error message summary in

Subsection 8.5.2 to take actions. Subsection 8.5.2 to take actions.

Is power supply NO
closed correctly?
polarity correct?
YES Fully close equalizing valve, and fully

YES Refer to Section 6.3 to check/correct open high pressure and low pressure
polarity at each terminal from power valves.
supply to the terminal box.
Is impulse piping NO
connected correctly?
closed correctly?
YES Refer to individual model user manuals

YES Fully close equalizing valve, and fully and connect piping as appropriate for
open high pressure and low pressure the measurement purpose.
valves.
Are power supply NO

YES voltage and load resistance
Is there any pressure leak?
correct?
NO YES Refer to Section 6.6 for rated voltage

Fix pressure leaks, paying particular and load resistance.
attention to connections for impulse
piping, pressure-detector section, etc.
Is transmitter
installed where there is YES
Is impulse piping NO
to high pressure and low marked variation in
pressure side correct? temperature?
Provide lagging and/or cooling, or allow

YES Refer to individual model user manuals NO adequate ventilation.
and connect piping as appropriate for
the measurement purpose.
Were appropriate NO
Is zero point NO instruments used for
adjusted correctly? calibration?
YES Refer to Section 9.2 when selecting

YES Adjust the zero point. instruments for calibration.
Contact Yokogawa service personnel. NO

Is output adjusted correctly?
F0908.ai
YES Adjust the output.
Contact Yokogawa service personnel.
F0909.ai
IM 01C21F01-01E
<10. General Specifications> 10-1
10. General Specifications

10.1 Standard Specifications Failure Alarm:
Output status at CPU failure and hardware
Refer to IM 01C22T02-01E for FOUNDATION error;
Fieldbus communication type and IM 01C22T03- Up-scale:
00E for PROFIBUS PA communication type marked 110%, 21.6 mA DC or more(standard)
with “◊”. Down-scale:
-5%, 3.2 mA DC or less
 Performance Specifications -2.5%, 3.6 mA DC or less(Optional code /F1)
Note: Applicable for Output signal code D and E
See General Specifications sheet, GS 01C21F01-
00E. Damping Time Constant (1st order):
The sum of the amplifier and capsule damping
 Functional Specifications
time constant must be used for the overall
time constant. Amp damping time constant is
Span & Range Limits adjustable from 0.2 to 64 seconds.
EJA510A and EJA530A: Capsule (Silicone Oil) A, B, C, and D
Measurement Time Constant (approx. sec) 0.2
psi bar kgf/cm2
Span MPa
(/D1) (/D3) (/D4)
and Range Ambient Temperature Limits:
10 to 200
Span 1.45 to 29 0.1 to 2 0.1 to 2 * Safety approval codes may affect limits.
kPa
A –40 to 85°C (–40 to 185°F)
0 to 200
Range 0 to 29 0 to 2 0 to 2 –30 to 80°C (–22 to 176°F) with LCD Display
kPa
14.5 to
Span 0.1 to 2 1 to 20 1 to 20 Process Temperature Limits:
B 290
Range 0 to 2 0 to 290 0 to 20 0 to 20 * Safety approval codes may affect limits.
72.5 to –40 to 120°C (–40 to 248°F)
Span 0.5 to 10 5 to 100 5 to 100
C 1450
Maximum Overpressure:
Range 0 to 10 0 to 1450 0 to 100 0 to 100
Capsule
720 to
Span 5 to 50 50 to 500 50 to 500 Capsule EJA510A EJA530A
D 7200
Range 0 to 50 0 to 7200 0 to 500 0 to 500 A 4 MPa abs{580 psia} 4 MPa {580 psig}
B 4 MPa abs{580 psia} 4 MPa {580 psig}
Values in absolute for EJA510A.
C 20 MPa abs{2900 psia} 20 MPa {2900 psig}
Zero Adjustment Limits: D 60 MPa abs{8500 psia} 60 MPa {8500 psig}
Zero can be fully elevated or suppressed,
within the Lower and Upper Range Limits of the Working Pressure Limits (Silicone Oil)
capsule. Maximum Pressure Limit:
External Zero Adjustment “◊”: Capsule
External zero is continuously adjustable with Capsule EJA510A EJA530A
0.01% incremental resolution of span. Span A 200 kPa abs{29 psia} 200 kPa {29 psig}
may be adjusted locally using the digital B 2 MPa abs{290 psia} 2 MPa {290 psig}
indicator with range switch. C 10 MPa abs{1450 psia} 10 MPa {1450 psig}
Output “◊”: D 50 MPa abs{7200 psia} 50 MPa {7200 psig}
Two wire 4 to 20 mA DC output with digital
communications, linear or square root Minimum Pressure Limit:
programmable. BRAIN or HART FSK protocol EJA510A: 0.013 kPa abs
are superimposed on the 4 to 20 mA signal. EJA530A: Lower limit of measurement range
IM 01C21F01-01E
 Installation Where:
L = length in meters or feet
Supply & Load Requirements “◊”: R = resistance in Ω (including barrier
* Safety approvals can affect electrical resistance)
requirements. C = cable capacitance in pF/m or pF/ft
See Section 6.6, ‘Power Supply Voltage and Cf = maximum shunt capacitance of
Load Resistance.’ receiving devices in pF/m or pF/ft
Supply Voltage “◊”:
 Physical Specifications
10.5 to 42 V DC for general use and flameproof
type Wetted Parts Materials:
10.5 to 32 V DC for lightning protector (Optional Diaphragm and Process connector;
code /A) See ‘Model and Suffix Codes’
10.5 to 30 V DC for intrinsically safe, Type n,
nonincendive, or non-sparking type Non-wetted Parts Materials:
Minimum voltage limited at 16.4 V DC for digital Housing;
communications, BRAIN and HART Low copper cast-aluminum alloy with
polyurethane paint (Munsell 0.6GY3.1/2.0)
EMC Conformity Standards: Degrees of Protection
EN 61326-1 Class A, Table 2 (For use in IP67, NEMA4X
industrial locations) Cover O-rings;
EN 61326-2-3 Buna-N, Fluoro-rubber (option)
EN 61326-2-5 (for Fieldbus) Data plate and tag;
Immunity influence during the test SUS304 or SUS316(optional)
Differential pressure/pressure: Output shift is Fill Fluid;
specified within ±1% of 1/10 Max span. Silicone or Fluorinated oil (optional)
Communication Requirements “◊”: Weight:
BRAIN 1.6 kg (3.5 lb) without integral indicator and
Communication Distance; mounting bracket.
Up to 2 km (1.25 miles) when using CEV Connections:
polyethylene-insulated PVC-sheathed See ‘Model and Suffix Codes.’
cables.
Communication distance varies depending < Settings When Shipped > “◊”
on type of cable used.
Tag Number As specified in order *1
Load Capacitance; Output Mode ‘Linear’
0.22 μF or less (see note) Display Mode ‘Linear’
Load Inductance; ‘Normal’ unless otherwise
Operation Mode
3.3 mH or less (see note) specified in order
Input Impedance of communicating device; Damping Time
‘2 sec.’
10 kΩ or more at 2.4 kHz. Constant
Note: For general-use and Flameproof type. For Calibration Range
As specified in order
Intrinsically safe type, please refer to ‘Optional Lower Range Value
Specifications.’ Calibration Range
As specified in order
Higher Range Value
HART
Selected from mmH2O, mmAq,
Communication Distance; mmWG, mmHg, Torr, Pa, hPa,
Up to 1.5 km (1 mile) when using multiple Calibration Range kPa, MPa, mbar, bar, gf/cm2,
twisted pair cables. Communication distance Units kgf/cm2, inH2O, inHg, ftH2O, psi
or atm.
varies depending on type of cable used.
(Only one unit can be specified)
Use the following formula to determine cable
*1: If Tag No. is no more than 16 alphanumeric characters
length for specific applications: (including - and ·), it will be written into the tag plate and
65 x 106 (Cf + 10,000) amplifier memory settings.
L= −
(R x C) C
IM 01C21F01-01E
10.2 Model and Suffix Codes
 Model EJA510A and EJA530A

Model Suffix Codes Description
EJA510A ........................... Absolute pressure transmitter
EJA530A ........................... Gauge pressure transmitter
Output -D . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (BRAIN protocol)
Signal -E . . . . . . . . . . . . . . . . . . . . . . . . . 4 to 20 mA DC with digital communication (HART protocol, see IM 01C22T01-01E)
-F . . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (FOUNDATION Fieldbus protocol, see IM 01C22T02-01E)
-G . . . . . . . . . . . . . . . . . . . . . . . . Digital communication (PROFIBUS PA protocol, see 01C22T03-00E)
Measurement A . . . . . . . . . . . . . . . . . . . . . . . 10 to 200 kPa {0.1 to 2 kgf/cm2}
span (capsule) B . . . . . . . . . . . . . . . . . . . . . . . 0.1 to 2 MPa {1 to 20 kgf/cm2}
C . . . . . . . . . . . . . . . . . . . . . . . 0.5 to 10 MPa {5 to 100 kgf/cm2}
D . . . . . . . . . . . . . . . . . . . . . . . 5 to 50 MPa {50 to 500 kgf/cm2}
Wetted parts [Process Connection] [Diaphragm]
material S . . . . . . . . . . . . . . . . . . . . SUS316L Hastelloy C-276
H . . . . . . . . . . . . . . . . . . . . Hastelloy C-276 Hastelloy C-276
Process connection 4 . . . . . . . . . . . . . . . . . 1/2 NPT female
7 . . . . . . . . . . . . . . . . . 1/2 NPT male
8 . . . . . . . . . . . . . . . . . G 1/2 DIN 16 288 male
9 . . . . . . . . . . . . . . . . . M20 × 1.5 DIN 16 288 male
— N . . . . . . . . . . . . . . . Always N
— -0 . . . . . . . . . . . . Always 0
Electrical connection 0 . . . . . . . . . . G1/2 female, one electrical connection
2 . . . . . . . . . . 1/2 NPT female, two electrical connections without blind plug
3 . . . . . . . . . . Pg 13.5 female, two electrical connections without blind plug
4 . . . . . . . . . . M20 female, two electrical connections without blind plug
5 . . . . . . . . . . G1/2 female, two electrical connections and a blind plug
7 . . . . . . . . . . 1/2 NPT female, two electrical connections and a blind plug
8 . . . . . . . . . . Pg 13.5 female, two electrical connections and a blind plug
9 . . . . . . . . . . M20 female, two electrical connections and a blind plug
A . . . . . . . . . . G1/2 female, two electrical connections and a SUS316 blind plug
C . . . . . . . . . . 1/2 NPT female, two electrical connections and a SUS316 blind plug
D . . . . . . . . . . M20 female, two electrical connections and a SUS316 blind plug
Integral indicator D . . . . . . . Digital indicator
E . . . . . . . Digital indicator with the range setting switch
N . . . . . . . (None)
Mounting bracket E . . . . SECC Carbon steel 2-inch pipe mounting
F . . . . SUS304 2-inch pipe mounting
L . . . . SUS316 2-inch pipe mounting
N . . . . (None)
Optional codes / Optional specification
IM 01C21F01-01E
10.3 Optional Specifications
For FOUNDATION Fieldbus explosion protected type, see IM 01C22T02-01E.
For PROFIBUS PA explosion protected type, see IM 01C22T03-00E.
Item Description Code
FM Explosionproof Approval *1
Explosionproof for Class I, Division 1, Groups B, C and D
Dust-ignitionproof for Class II/III, Division 1, Groups E, F and G
FF1
Hazardous (classified) locations, indoors and outdoors (NEMA 4X)
Temperature class: T6
Amb. Temp.: –40 to 60°C (–40 to 140°F)
FM Intrinsically safe Approval *1
Intrinsically Safe for Class I, Division 1, Groups A, B, C & D, Class II, Division 1,
Groups E, F & G and Class III, Division 1 Hazardous Locations.
Factory Mutual (FM)
Nonincendive for Class I, Division 2, Groups A, B, C & D, Class II, Division. 2,
Groups E, F & G, and Class III, Division 1 Hazardous Locations.
Enclosure: “NEMA 4X”, Temp. Class: T4, Amb. Temp.: –40 to 60°C (–40 to 140°F) FS1
Intrinsically Safe Apparatus Parameters
[Groups A, B, C, D, E, F and G]
Vmax=30 V, Imax=165 mA, Pmax=0.9 W, Ci=22.5 nF, Li=730 µH
[Groups C, D, E, F and G]
Combined FF1 and FS1 *1 FU1
ATEX Flameproof Approval *2
Certificate: KEMA 02ATEX2148
II 2G Exd IIC T4, T5, T6 KF21
Amb. Temp.: T5; –40 to 80°C (–40 to 176°F), T4 and T6; –40 to 75°C (–40 to 167°F)
ATEX Max. process Temp.: T4; 120°C (248°F), T5; 100°C (212°F), T6; 85°C (185°F)
ATEX Intrinsically safe Approval *2
Certificate: KEMA 02ATEX1030X
KS2
II 1G EEx ia IIC T4, Amb. Temp.: –40 to 60°C (–40 to 140°F)
Ui=30 V, Ii=165 mA, Pi=0.9 W, Ci=22.5 nF, Li=730 µH
CSA Explosionproof Approval *1
Certificate: 1089598
Explosionproof for Class I, Division 1, Groups B, C and D
Dustignitionproof for Class II/III, Division 1, Groups E, F and G
Division2 ‘SEALS NOT REQUIRED’ , Temp. Class: T4, T5, T6 Encl Type 4x
Max. Process Temp.: T4; 120°C (248°F), T5; 100°C (212°F), T6; 85°C (185°F) CF1
Amb. Temp.: –40 to 80°C (–40 to 176°F)
Process Sealing Certification
Dual seal certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required. Primary seal failure annunciation : at the zero-
adjustment screw
Canadian Standards
CSA Intrinsically safe Approval *1
Association (CSA)
Certificate: 1053843
Intrinsically Safe for Class I, Groups A, B, C and D Class II and III, Groups E, F and G
Nonincendive for Class I, Division 2, Groups A, B, C and D Class II, Division 2,
Groups F and G and Class III (not use Safety Barrier)
Encl Type 4x, Temp. Class: T4, Amb. Temp.: –40 to 60°C (–40 to 140°F) CS1
Process Sealing Certification
Dual seal certified by CSA to the requirement of ANSI/ISA 12.27.01
No additional sealing required. Primary seal failure annunciation : at the zero-
adjustment screw
Combined CF1 and CS1 *1 CU1
IM 01C21F01-01E
IECEx Intrinsically safe, type n and Flameproof Approval *3
Intrinsically safe and type n
Certificate: IECEx KEM 06.0007X
Ex ia IIC T4, Ex nL IIC T4 Enclosure: IP67
Amb. Temp.: –40 to 60°C (–40 to 140°F), Max. Process Temp.: 120°C (248°F)
Electrical Parameters:
[Ex ia] Ui=30 V, Ii=165 mA, Pi=0.9 W, Ci=22.5 nF, Li=730 µH
IECEx Scheme SU2
[Ex nL] Ui=30 V, Ci=22.5 nF, Li=730 µH
Flameproof
Certificate: IECEx KEM 06.0005
Ex d IIC T6...T4 Enclosure: IP67
Max.Process Temp.: T4;120°C (248°F), T5;100°C (212°F), T6; 85°C (185°F)
Amb.Temp.: –40 to 75°C (–40 to 167°F) for T4, –40 to 80°C (–40 to 176°F) for T5,
–40 to 75°C (–40 to 167°F) for T6
*1: Applicable for Electrical connection code 2 and 7 (1/2 NPT female).
*2: Applicable for Electrical connection code 2, 4, 7 and 9 (1/2 NPT and M20 female).
*3: Applicable for Electrical connection code 2, 4 and 7 (1/2 NPT and M20 female).

Amplifier cover only P
Color change
Painting Amplifier cover and terminal cover, Munsell 7.5 R4/14 PR
Coating change Epoxy resin-baked coating X1
Exterior parts on the amprifier housing (name plates, tag plate, zero-adjustment
316 SST exterior parts HC
screw, stopper screw) will become 316 or 316L SST.
Fluoro-rubber O-ring All O-rings of amplifier housing. Lower limit of ambient temperature : –15°C (5°F) HE
Transmitter power supply voltag: 10.5 to 32 V DC (10.5 to 30 V DC for intrinsically
safe type, 9 to 32 V DC for FOUNDATION Fieldbus and PROFIBUS PA communication
Lightning protector A
type.)
Allowable current: Max. 6000 A (1×40 µs), Repeating 1000 A (1×40 µs) 100 times
Degrease cleansing treatment K1
Oil-prohibited use Degrease cleansing treatment with fluorinated oil filled capsule.
K2
Operating temperature –20 to 80 °C
P calibration (psi unit ) D1
(See Table for Span and Range
Calibration units bar calibration (bar unit ) D3
Limits.)
M calibration (kgf/cm2 unit ) D4
Fast response *2 Update time: 0.125 sec or less, see GS for response time F1
Failure alarm
Output status at CPU failure and hardware error is –5%, 3.2 mA or less. C1
down-scale *1
Failure alarm down-scale: output status at CPU failure and
C2
NAMUR NE43 Output signal limits: hardware error is –5%, 3.2 mA or less.
compliant *1 3.8 mA to 20.5 mA Failure alarm up-scale: output status at CPU failure and
C3
hardware error is 110%, 21.6 mA or more.
Data configuration at
Description into “Descriptor” parameter of HART protocol CA
factory
Stainless steel amplifier Amplifier housing material: SCS14A stainless steel
E1
housing (equivalent to SUS316 cast stainless steel or ASTM CF-8M)
Stainless steel tag plate SUS 304 stainless steel tag plate wired onto transmitter N4
High Accuracy type High Accuracy (Applicable for Model EJA530A) HAC
PED 97/23/EC
European Pressure
CATEGORY: III, Module: H, Type of Equipment: Pressure Accessory - Vessel, PE3
Equipment Directive
Type of Fluid: Liquid and Gas, Group of Fluid: 1 and 2
Mill Certificate Process connector M15
Test Pressure: 200 kPa{2 kgf/cm2} T05
Pressure test/Leak test Test Pressure: 2 MPa{20 kgf/cm2} Nitrogen(N2) Gas T06
Certificate Test Pressure: 10 MPa{100 kgf/cm2} Retention time: 10 minutes T07
Test Pressure: 50 MPa{500 kgf/cm2} T08
*1: Applicable for Output signal code D and E. The hardware error indicates faulty amplifier or capsule. When combining with Optional
code F1, output status for down-scale is –2.5%, 3.6 mA DC or less.
*2: Applicable for Output signal code D and E. Write protection switch is attached for Output code E.
IM 01C21F01-01E
10.4 Dimensions
 Model EJA510A and EJA530A [Style: S2]
Unit: mm (approx. inch)

 With Process Connection code 7
96(3.77) 41(1.61) 110(4.33)
Conduit connection 12 45
(0.47) (1.77) Ground terminal
Shrouding bolt *2
(3.07)
Ø78
127(5.0)
111(4.37)
170(6.69)
LOCK ZERO LOCK
Zero adjustment
Adapter
124(4.88)
Pipe(Open to atmosphere)*1
44(1.73)
(1.85)
47
2-inch pipe Mounting bracket

91(3.58)
(O. D. 60.5 mm)
*1: Applied to Model EJA530A with Measurement span code A, B, and C.

*2: Applicable only for ATEX and IECEx Flameproof type.
 For Process Connection code 4

163(6.41)
 For Process Connection code 8 and 9

20(0.78)
176(6.92)
Ø6(0.23)
5(0.19)
F1001.ai
IM 01C21F01-01E
Customer Model EJA510A and EJA530A
Maintenance Absolute and Gauge
Parts List Pressure Transmitter
2 5
4
11
A 10
12
13 1
2 2
1
14
A
6
7-2
7-1 5
8 9
18
17
15 15
16
15
Process connection Process connection

code 4 code 8 and 9
Process connection
code 7
21
19
22
24
20 23
All Rights Reserved. Copyright © 1999, Yokogawa Electric Corporation

CMPL 01C21F01-01E
Subject to change without notice.
6th Edition: Oct. 2008 (YK)
2
Item Part No. Qty Description
1 Bellow 2 Cover
F9341RA Cast-aluminum alloy
F9341RJ SCS14A stainless steel
2 F9341JP 2 O-ring
3 Below 1 Case Assembly (Note 1)
F9341AA Cast-aluminum alloy for G1/2

F9341AC Cast-aluminum alloy for G1/2 (two electrical connections)
F9341AE Cast-aluminum alloy for 1/2 NPT (two electrical connections)
F9341AH Cast-aluminum alloy for M20 (two electrical connections)
F9341AJ Cast-aluminum alloy for Pg13.5 (two electrical connections)
F9341AR SCS14A stainless steel for 1/2 NPT (two electrical connections)
4 F9341KA 1 Name Plate
5 Bellow 4 Screw
F9900RG For cast-aluminum alloy case assembly
F9900RR For SCS14A stainless steel case assembly
6 F9341KL 1 Tag Plate

7-1 Below 1 CPU Assembly
F9342AB For BRAIN protocol version
F9342AL For HART protocol version
F9342AF For BRAIN protocol version (Optional code /F1)
F9342AM For HART protocol version with write protection switch (Optional code /F1)
7-2 F9342BF 1 For FOUNDATION Fieldbus protocol version
F9342BG For FOUNDATION Fieldbus protocol version with PID/LM function (Optional code /LC1)
8 F9900RP 2 Cap Screw
9 Y9612YU 2 Screw
10 Below 1 Plug
F9340NW For Pg13.5
F9340NX For M20
G9330DK For G1/2
G9612EB For 1/2 NPT
11 Bellow 1 Cover Assembly

F9341FM Cast-aluminum alloy
F9341FJ SCS14A stainless steel
12 Below 1 LCD Board Assembly
F9342BL Without range-setting switch For integral indicator
F9342BM With range-setting switch

13 F9342MK 2 Mounting Screw
14 F9300PB 2 Label
15 1 Capsule Assembly (See Table 1.)(Note 2)
16 F9300AJ 1 O-ring
17 Below 1 Pipe (for EJA530A with Measurement Span code A, B, and C)

F9385XK Polypropylene resin
F9385XM SUS316 Stainless Steel (Optional code /E1)
18 F9385XL 1 O-ring (for EJA530A with Measurement Span code A, B, and C)
19 F9385XZ 1 Plate, SUS304 Stainless Steel
20 Below 1 Bracket Assembly

F9385XV SECC carbon steel
F9385XT SECC carbon steel (for epoxy resin-baked coating)
F9385XU SUS304 stainless steel
21 D0117XL-A 1 U-bolt/Nut Assembly (L), SUS304 Stainless Steel
22 Below 1 Bracket
F9270AX SECC carbon steel
F9300TN SECC carbon steel (for epoxy resin-baked coating)
F9300TE SUS304 Stainless Steel
23 F9385XW 1 U-bolt/Nut Assembly (S), SUS304 Stainless Steel
24 F9385XY 1 Adapter, SUS304 Stainless Steel
(Note 1) Applicable for BRAIN and HART protocol versions (Output signal code D and E).
For FOUNDATION Fieldbus protocol version (Output signal code F), consult Yokogawa local office.
(Note 2) In case of Degrease cleansing treatment (Optional code /K1), consult Yokogawa local office.
Jan. 2008 CMPL 01C21F01-01E

3
Table 1. Capsule Assembly Part Number (Item 15)
Process Capsule EJA510A EJA530A
connection Code S(*1) S, /K2(*2) H(*1) H, /K2(*2) S(*1) S, /K2(*2) H(*1) H, /K2(*2)
A F9421AB F9421AP F9421NB F9421NP F9420AB F9420AP F9420NB F9420NP
1/2 NPT B F9421BB F9421BP F9421PB F9421PP F9420BB F9420BP F9420PB F9420PP
female C F9421CB F9421CP F9421QB F9421QP F9420CB F9420CP F9420QB F9420QP
D F9421DB F9421DP F9421RB F9421RP F9420DB F9420DP F9420RB F9420RP
A F9421AD F9421AR F9421ND F9421NR F9420AD F9420AR F9420ND F9420NR
1/2 NPT B F9421BD F9421BR F9421PD F9421PR F9420BD F9420BR F9420PD F9420PR
male C F9421CD F9421CR F9421QD F9421QR F9420CD F9420CR F9420QD F9420QR
D F9421DD F9421DR F9421RD F9421RR F9420DD F9420DR F9420RD F9420RR
A F9421AE F9421AS F9421NE F9421NS F9420AE F9420AS F9420NE F9420NS
G1/2 male B F9421BE F9421BS F9421PE F9421PS F9420BE F9420BS F9420PE F9420PS
(DIN) C F9421CE F9421CS F9421QE F9421QS F9420CE F9420CS F9420QE F9420QS
D F9421DE F9421DS F9421RE F9421RS F9420DE F9420DS F9420RE F9420RS
A F9421AF F9421AT F9421NF F9421NT F9420AF F9420AT F9420NF F9420NT
M20×1.5 B F9421BF F9421BT F9421PF F9421PT F9420BF F9420BT F9420PF F9420PT
male C F9421CF F9421CT F9421QF F9421QT F9420CF F9420CT F9420QF F9420QT
D F9421DF F9421DT F9421RF F9421RT F9420DF F9420DT F9420RF F9420RT
*1: Silicone oil filled capsule (Standard)
*2: Fluorinated oil filled capsule (for oil-prohibited use: optional code /K2)
Jan. 2008 CMPL 01C21F01-01E

Revision Information
 Title : Model EJA510A and EJA530A
Absolute Pressure and Gauge Pressure Transmitter
 Manual No. : IM 01C21F01-01E
Edition Date Page Revised Item

1st June 1999 — New publication
2nd June 2000 CONTENTS Page 3 Add REVISION RECORD.
2-8 2.9.4 b Add maximum process temperature of –40 to 75°C for KEMA
Flameproof type T6.
Change wating period when opening terminal cover after power
off from 1 min. to 10 min.
Add note for using heat-resisting cables.
8-4 8.3.1 Add footnote *2 for amp. damping time constant when Optional
code /F1 is specified.
8-5 Add footnote *3 for low side output status at failure alarm when
Optional code /F1 is specified.
10-4 10.3 Change explosion protected type Optional code from /1 to
/11.
Add maximum process temperature of –40 to 75°C for KEMA
Flameproof type T6.
10-5 Add Optional code /F1 and /N4.
CMPL CMPL 1C21F1-01E 1st → 2nd
Page 2 Change Part No. on Item 7, CPU Assembly.
F9342BP → F9342AB
F9342BQ → F9342AL
Add Part No. on Item 7, CPU Assembly.
F9342AF for BRAIN protocol, Optional code /F1
F9342AM for HART protocol, Optional code /F1
3rd Aug. 2001 — Style change from S1 to S2.
2-8 2.10 Change EMC Conformity number.
8-4, 8-5 8.3.1 Add footnote (*4) to B40, Maximum static pressure in Parameter
Summary.
10-1 10.1 Change Maximum Over pressure for Capsule code A from 400
kPa to 4 MPa.
10-4 10.3 Change explosion protected type Optional code from /11 to
/1.
10-6 10.4 Change dimensions.
CMPL CMPL 1C21F1-01E 2nd → 3rd
Change Part No. on Item 15, Capsule Assembly and followings.
Item 17; F9374MS → F9385XK, F9385XM
Item 18; F9374MU → F9385XL
Item 19; F9374NZ → F9385XZ
Item 20; F9374MX → F9385XV, F9374NX → F9385XT,
F9374MW → F9385XU
Item 23; F9374MY → F9385XW
Item 24; F9374NY → F9385XY
4th May 2002 1-2 1.1 Add “1.1 For Safety Using.”
2-7 2.9.4 Add descriptions based on ATEX directive.
10-4 10.3 Add Optional code K2.
10-5 Add Optional code C2 and C3.
5th Apr. 2003 2-8 2.9.4 Add Option code KU2.
2-10 2.11 Add PED (Pressure Equipment Directive).
10-3 10.2 Add Output Signal code F.
10-4 10.3 Add Option code KU2.
10-5 Add Option code HAC and PE3.
CMPL CMPL 01C21F01-01E 3rd → 4th
Add part No. on Item 7-2, CPU Assembly for fieldbus protocol.
IM 01C21F01-01E
Edition Date Page Revised Item
6th Apr. 2006 1-2 1.1 Add (e) Explosion Protected Type Instrument and (f) Modification
1-3 1.3 Add “1.3 ATEX Document”
2-6 2.9.3 Add “IECEx Certification” and delete “SAA Certification”
2-11 2.12 Add Low Voltage Directive
10-4, 10-5 10.3 Add Certificate numbers and Applicable standards
10-5 Add option code /SU2 and delete option code /SU1
10-6 Add option code /PR
7th Jan. 2008 1-1 Add direct current symbol.
1-4 Add 11 European languages for ATEX documentation.
2-3+ 2.9.1 Add applicable standard and certificate number for appovals.
2-10 2.10 Add EMC caution note.
4-2 4.4 Add section of changing the direction of integral indicator.
8-14 8.3.3(11) Add figure for A40.
9-4 9.4.1 Add figure of integral indicator direction.
10-1+ 10.1, 10.2 Add PROFIBUS PA communication type.
10-4,10-5 10.3 Delete applicable standard from the table.
CMPL CMPL 01C21F01-01E 4th → 5th
Delete logo from the tag plate.
8th Oct. 2008 2-9 2.9.4 Change explosion protection marking for type n from EEx to Ex.
2-10 2.10 Update EMC conformity standards.
8-4 and 8-5 8.3.1 Add new parameters.
8-6 8.3.2 Add items in table 8.3.1.
8-9 and later 8.3.3 Add (5)Change Output Limits and (13)Span Adjustment.
Re-number the items.
8-18 8.5.2 Modify descriptions and notes for Er.01.
9-1 9.3 Add a note for calibration.
9-5 9.4.3 Add a note for cleaning.
10-3 10.2 Add new suffix codes.
10-5, 10-6 10.3 Add sealing statement for CSA standards. Add /HC.
CMPL CMPL 01C21F01-01E 7th → 8th
Change Part No. of items 5 and 8.
9th July 2015 2-5, 2-6 2.9.2 Add temperature limitation for /HE.
2-9 to 2-10 2.9.4 b Change /KF2 to /KF21 and modify descriptions. Delete c.
Replace tag plate.
2-11 2.10 Add standards.
2-12 2.12 Add (3) and (4).
8-1 8.1.1 Add note. 8.1.2 Add descriptions.
10-2 10.1 Add information to “EMC Conformity Standards”.
10-4 to 10-5 10.3 Delete codes KU2 and KF2. Add KF21. Add Codes HE and CA.
IM 01C21F01-01E

User's Manual: Model EJA510A and EJA530A Absolute Pressure and Gauge Pressure Transmitters (Style: S2)

Uploaded by

Copyright:

Available Formats

User's Manual: Model EJA510A and EJA530A Absolute Pressure and Gauge Pressure Transmitters (Style: S2)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

User's Manual: Model EJA510A and EJA530A Absolute Pressure and Gauge Pressure Transmitters (Style: S2)

Uploaded by

Copyright:

Available Formats

User’s

Manual Model EJA510A and EJA530A

Model EJA510A and EJA530A

9th Edition: July 2015 (KP) IM 01C21F01-01E

• The following safety symbol marks are used in

2.1 Model and Specifications 2.4 Selecting the Installation

• Installation should be in accordance with

Hazardous Location Nonhazardous Location

Caution for ATEX flameproof type. ANSI 1/2 NPT female A

Note 1. Model EJA Series differential, gauge,

both of Division 1 and Division 2 hazardous

MODEL: Specified model code.

The year 2001

2-9-32 Nakacho, Musashino-shi, Tokyo Japan

(1) Pollution Degree 2

Terminal box cover

Setting pin (CN4) Capsule assembly

Figure 3.1 Component Names

Table 3.1 Display Symbol

Horizontal pipe mounting

Figure 4.2 Gasketing

Allen screw Capsule assembly

Figure 4.4 Rotating Transmitter Section

Figure 4.3 Tightening Transmitter

Figure 4.5 Integral Indicator Direction

5. Installing Impulse Piping

Figure 5.2 Process Pressure Tap Angle

Pipe Zero-adjustment screw

(4) Preventing Freezing

NOTE Figure 5.3 Impulse Piping Connection Examples

After completing the connections, close the

5.2 Impulse Piping Connection

silicone group sealant is recommended.)

Figure 6.2 External Indicator Connection

6.2 Selecting the Wiring 6.3.3 BRAIN TERMINAL BT200

6.4 Wiring 6.4.2 Wiring Installation

6.4.1 Loop Configuration (1) General-use Type and Intrinsically Safe

(1) General-use Type and Flameproof Type

Receiver Flexible metal conduit

Flameproof packing adapter

■ Flameproof metal conduit wiring Figure 6.10 Ground Terminals

Figure 6.9 Typical Wiring Using Flameproof Metal

Figure 6.11 Relationship between Power Supply

2) Gradually open the stop valve to introduce

 Using the BT200

CLR ESC for 40% output 10.4 mA DC.

rotating the external zero-adjustment screw. Figure 7.2 Range-setting Switch

8. BRAIN TERMINAL BT200 Operation

• Communication Line Requirements

Load Cable DPharp

● Loop resistance = R + 2Rc

Figure 8.2 Conditions of Communication Line

Shift keys F0805.ai

Function keys a. Entering Digits, Symbols, and Spaces

Power ON/OFF key –4

b. Entering Letters (A through Z)

HOME SET ADJ ESC

PARAMETER SCREEN Entry Key-in Sequence

uppercase and lowercase (for letters only). The