Gagemaker Products

102 Automotive Oil & Gas Renewable Energies

 GAGEMAKER
PRODUCTS

Aerospace Mechanical Engineering 103

 Gagemaker Products
MRP-1000 MRP-202
Pitch Diameter and Ovality Gages
MRP Pitch Diameter and Ovality Gages
This MRP series of pitch diameter gages detects variations in pitch diameter by the use of a gage shoe
that rests on the crest of the threads. Variation in diameter is detected by the indicator readout. These
gages must be set to nominal size with one of a variety of setting options offered. All of these gages
are API approved for use on tubing and casing.

Model Description Range

MRP-202 Internal Small Pitch Diameter Thread Gage Internal 1” - 2½”
MRP-1000 External/Internal Pitch Diameter Gage 1½” - 4½”
MRP-1001
MRP-1001 External Pitch Diameter Gage External 1½” - 4½”
Internal Seal Diameter Gage. Contacts on a 45° angle.
MRP-1012-TST MRP-1000-45 Internal 1” - 4½”
Arms: ⅜” upper arms, ⅜” lower arms
Internal Seal Diameter Gage. Contacts on a 45° angle.
MRP-1007 Internal 1½” - 4½”
MRP-1012-TSS Arms: .740" upper, ½” lower
with contact points Internal Seal Diameter Gage. Contacts on a 45° angle.
MRP-1008 Internal 1⅜” - 4½”
Arms: .740" upper, .740” lower
Internal Seal Diameter Gage. Contacts on a 45° angle.
MRP-1009 Internal 1⅜” - 4½”
Arms: .740" upper, .500” lower
Internal/External Pitch Diameter Gage for Two Step Seal. Upper
Internal 2⅜” - 4½”
MRP-1012-TSS and lower arms are .740” diameter. Upper arm has standard travel
External 1¾” - 4½”
of .150”. Shipped with T105 pts.
Internal/External Pitch Diameter Gage, Two Step Thread, w/ Internal 2⅜” - 4½”
MRP-1012-TST 1.030” Horseshoe standoff for front and rear measurements. Arms
MRP-2001
have .740” diameter. Upper arm has extended travel of .350” External 1¾” - 4½”
Internal 1½” - 4½”
MRP-1500 Internal/External Pitch Diameter Gage, Solid Body
External 2⅞” - 4½”
MRP-2001 External Pitch Diameter Gage, 4½” reach
MRP-2001-S External Pitch Diameter Gage, 4½” reach, Straight Blocks
External 2⅜” - 20”
MRP-2001-7 External Pitch Diameter Gage, 7” reach
MRP-2001-10 External Pitch Diameter Gage, 10” reach
MRP-2002 MRP-2002 Internal Pitch Diameter Gage, 4¼” reach
Internal 2⅜” - 20”
MRP-2002-S Internal Pitch Diameter Gage, 4¼” reach, Straight Blocks
MRP-2002-7 Internal Pitch Diameter Gage, 7” reach
Internal 3½” - 20”
MRP-2002-10 Internal Pitch Diameter Gage, 10” reach
MRP-2003 Internal/External Pitch Diameter Gage, 4¼” reach
2⅜” - 20”
MRP-2511 MRP-2003-S Internal/External Pitch Diameter Gage, 4¼” reach, Straight Blocks
MRP-2003-7 Internal/External Pitch Diameter Gage, 7” reach Internal 3½” - 20”
MRP-2003-10 Internal/External Pitch Diameter Gage, 10” reach External 2⅜” - 20”
MRP-2511 External Pitch Diameter Gage, 4” reach
MRP-2512 External 4½” - 9⅝”
MRP-2511-7 External Pitch Diameter Gage, 7” reach
MRP-2521 External Pitch Diameter Gage, 4” reach External 4½” - 13⅜”
MRP-2512 Internal Pitch Diameter Gage, 3⅜” reach
Internal 4½” - 9⅝”
MRP-2512-7 Internal Pitch Diameter Gage, 7” reach
MRP-2522 Internal Pitch Diameter Gage, 3⅜” reach Internal 4½” - 13⅜”
MRP-2513 Internal/External PD Gage, 3⅜” reach 4½” - 9⅝”
MRP-2523 Internal/External PD Gage, 3⅜” reach 4½” - 13⅜”
1
-300 MRP-3001 External Pitch Diameter Gage, 3⅜” reach External 8⅝” - 24”
MRP
MRP-3002 Internal Pitch Diameter Gage, 3⅜” reach Internal 8⅝” - 24”
MRP-3003 Internal/External Pitch Diameter Gage, 3⅜” reach 8⅝” - 24”
MRP-3002 MRP-3004 Internal/External Pitch Diameter Gage, 3⅜” reach 20” - 36”
MRP-3501 External Pitch Diameter Gage, w/ 6¼” reach External 8⅝” - 24”
MRP-3502 Internal Pitch Diameter Gage, w/ 6¼” reach Internal 8⅝” - 24”
MRP-3503 Internal/External PD Gage, w/ 6¼” reach 8⅝” - 24”

104 www.gagemaker.com • [email protected]

MRP-1000, MRP-2000, & MRP-3000 Replacement Parts MRP-20BL
MRP-10BL
These are some of the most commonly requested replacement parts for the MRP gages. Additional
parts may be available.

Model Description
MRP-10BL MRP-1000 Block Set
MRP-10UA MRP-1000 Upper Arm
MRP-10LA MRP-1000 Lower Arm
MR
MRP-10WP MRP-1000 Wear Pad Set

X
PE
P-
20

0W
MRP-10SP MRP-1000 Spring Plunger WP

-3
-7

RP
MRP-20BL MRP-2000 Block Set

M
P
W
MRP-20CL MRP-2000 Series Arm Clamp - 20
RP
MRP-20LB-1 MRP-2000 Lower Block w/ 1” hole M

MRP-21UA MRP-2001 Upper Arm MRP-10WP

0UA
MRP-21LA MRP-2001 Lower Arm P-1
MR
MRP-21UA-7 MRP-2001 7” Upper Arm 0LA
P-1
MRP-21LA-7 MRP-2001 7” Lower Arm MR

MRP-21UA-10 MRP-2001 10” Upper Arm

2UA
MRP-21LA-10 MRP-2001 10” Lower Arm P-2
MR
MRP-.625I Int. Thread Shoe, ⅝” long, .125 Pivot Dimension
MRP-.625E Ext. Thread Shoe, ⅝” long, .250 Pivot Dimension 2LA
P-2
MRP-20mm Int./Ext. Thread Shoe, 20 mm long, .250 Pivot Dimension MR

MRP-20SP MRP-2000 Spring Plunger A

1U
MRP-22UA MRP-2002 Upper Arm P-2
MR
MRP-22LA MRP-2002 Lower Arm
MRP-22UA-7 MRP-2002 7” Upper Arm 1LA
P-2
MRP-22LA-7 MRP-2002 7” Lower Arm MR
-7
MRP-22UA-10 MRP-2002 10” Upper Arm UA
P -22
MRP-22LA-10 MRP-2002 10” Lower Arm MR

MRP-20WP MRP-2000 Wear Pad Set

-7
MRP-20WPEX MRP-2000 Extended Wear Pad Set LA
P -22
MRP-20WP-7 MRP-2000 Wear Pad Set, 7” reach MR MRP-20KB
MRP-20WP-10 MRP-2000 Wear Pad Set, 10” reach
MRP-10KB-L
MRP-RAIL-12 MRP-2000 12” Cross Rail MRP-10KB-S
MRP-RAIL-18 MRP-2000 18” Cross Rail
MRP-RAIL-24 MRP-2000 24” Cross Rail
MRP-10KB-S MRP-1000 Knob-Short
MRP-10KB-L MRP-1000 Knob-Long MRP-.625I MRP-.625E

MRP-20KB MRP-2000 Knob MRP Rails

MRP-.750 Ext. Thread Shoe, ¾” long, .250 Pivot Dimension
MRP-.875 Int./Ext. Thread Shoe, ⅞” long, .250 Pivot Dimension
MRP-1.00 Int./Ext. Thread Shoe, 1” long, .250 Pivot Dimension MRP-.875 MRP-1.00
MRP-30WP MRP-3000 Wear Pad Set
MRP-30WPEX MRP-3000 Extended Wear Pad Set
MRP-30RS-18 MRP-3000 Rail Set, 18” Max
MRP-30RS-24 MRP-3000 Rail Set, 24” Max
MRP-GSS MRP Gage Setting Stand MRP-GSS

Phone: 713-472-7360 • Fax: 713-472-7241 105

 Gagemaker Products

Pin Rod Standard

MRP Gage Setting Standards
in Case
Rod Style Setting Standards for MRP-1000, 1500, 2000, 2500, 3000, & 3500
Rod style setting standards are designed to preset select MRP Series models for accurate inspection
of API threaded connections. Each set of standards consists of two precision ground rods that are
ground to lengths in accordance with API Specification 5B. The rod sets are securely attached together
and labeled with the connection size and serial number. The rods set the location of the thread shoe
and the distance between shoes for accurate inspection of threaded connections.

Thread Connection Size Pin Model Box Model

Type
2⅜” EUE MRP-238EUE-P MRP-238EUE-B
2⅞” EUE MRP-278EUE-P MRP-278EUE-B
Pin Rod EUE 3½” EUE MRP-312EUE-P MRP-312EUE-B
Standard “A”
4” EUE MRP-4EUE-P MRP-4EUE-B
4½” EUE MRP-412EUE-P MRP-412EUE-B

Thread Connection Size Pin Model Box Model

Type
2⅜” NUE MRP-238NUE-P MRP-238NUE-B
2⅞” NUE MRP-278NUE-P MRP-278NUE-B
NUE 3½” NUE MRP-312NUE-P MRP-312NUE-B
4” NUE MRP-4NUE-P MRP-4NUE-B
4½” NUE MRP-412NUE-P MRP-412NUE-B

Thread Connection Size Pin Model Box Model

Type
Pin Rod Standard “B” 4½” Buttress MRP-412B-P MRP-412B-B
5” Buttress MRP-5B-P MRP-5B-B
5½” Buttress MRP-512B-P MRP-512B-B
6⅝” Buttress MRP-658B-P MRP-658B-B
7” Buttress MRP-7B-P MRP-7B-B
7⅝” Buttress MRP-758B-P MRP-758B-B
8⅝” Buttress MRP-858B-P MRP-858B-B
Buttress
9⅝” Buttress MRP-958B-P MRP-958B-B
10¾” Buttress MRP-1034B-P MRP-1034B-B
11¾” Buttress MRP-1134B-P MRP-1134B-B
13⅜” Buttress MRP-1338B-P MRP-1338B-B
16” Buttress MRP-16B-P MRP-16B-B
18⅝” Buttress MRP-1858B-P MRP-1858B-B
20” Buttress MRP-20B-P MRP-20B-B

Line Pipe standards are available. All Special Orders, Non-Standard API or Premium Connection
Setting Standards are extra. Please contact for more information.

106 www.gagemaker.com • [email protected]

Rod Style Setting Standards for MRP-1000, 1500, 2000, 2500, 3000, & 3500 Box Rod Standard
(Cont.) in Case

Thread Connection Size Pin Model Box Model

Type
4½” 8R LTC MRP-412L-P MRP-412L-B
5” 8R LTC MRP-5L-P MRP-5L-B
5½” 8R LTC MRP-512L-P MRP-512L-B
6⅝” 8R LTC MRP-658L-P MRP-658L-B
LTC 7” 8R LTC MRP-7L-P MRP-7L-B
7⅝” 8R LTC MRP-758L-P MRP-758L-B
8⅝” 8R LTC MRP-858L-P MRP-858L-B Box Rod
Standard “A”
9⅝” 8R LTC MRP-958L-P MRP-958L-B>P110 or MRP-958L-B<P110
20” 8R LTC MRP-20L-P MRP-20L-B>JK55 or MRP-20L-B<JK55

Thread Connection Size Pin Model Box Model

Type
4½” - 9.50# 8R STC MRP-412S-9-P MRP-412S-9-B
4½” - Other 8R STC MRP-412S-O-P MRP-412S-O-B
5” - 11.50# 8R STC MRP-5S-11-P MRP-5S-11-B
5” - Other 8R STC MRP-5S-O-P MRP-5S-O-B
5½” 8R STC MRP-512S-P MRP-512S-B
6⅝” 8R STC MRP-658S-P MRP-658S-B
7” - 17.00# 8R STC MRP-7S-17-P MRP-7S-17-B
7” - Other 8R STC MRP-7S-O-P MRP-7S-O-B
7⅝” 8R STC MRP-758S-P MRP-758S-B
STC 8⅝” - 24.00# 8R STC MRP-858S-24-P MRP-858S-24-B
8⅝” - Other 8R STC MRP-858S-O-P MRP-858S-O-B
9⅝” 8R STC MRP-958S-P MRP-958S-B>P110 or MRP-958S-B<P110
10¾” - 32.75# 8R STC MRP-1034S-32-P MRP-1034S-32-B
10¾” - Other 8R STC MRP-1034S-O-P MRP-1034S-O-B>P110 or MRP-1034S-O-B<P110 Box Rod
Standard “B”
11¾” 8R STC MRP-1134S-P MRP-1134S-B>P110 or MRP-1134S-B<P110
13⅜” 8R STC MRP-1338S-P MRP-1338S-B>P110 or MRP-1338S-B<P110
16” 8R STC MRP-16S-P MRP-16S-B
18⅝” 8R STC MRP-1858S-P MRP-1858S-B
20” 8R STC MRP-20S-P MRP-20S-B>JK55 or MRP-20S-B<JK55

Line Pipe standards are available. All Special Orders, Non-Standard API or Premium Connection
Setting Standards are extra. Please contact for more information.

Phone: 713-472-7360 • Fax: 713-472-7241 107

 Gagemaker Products

Frame Style Setting Standards for MRP-1000, 1500, 2000, 2500, 3000, &
3500 Series*
These frame style setting standards are designed to preset multiple models of the MRP Series
gages for accurate inspection of API threaded connections. These standards consist of a rigid,
non-adjustable steel block precision machined to proper size to tolerances of ±.0003”. Round style
standards, smaller than 2⅜", are available as specials (contact us directly for more information).
When ordering, please specify the gage to be used.

Thread
Connection Size Pin Model Box Model
MRP Series Type
Frame Style Standards 2⅜” NUE FSTD-238N-P2 FSTD-238N-B2
2⅞” NUE FSTD-278N-P2 FSTD-278N-B2
NUE
3½” NUE FSTD-312N-P2 FSTD-312N-B2
4½” NUE FSTD-412N-P2 FSTD-412N-B2

Thread
Connection Size Pin Model Box Model
Type
2⅜” EUE FSTD-238E-P2 FSTD-238E-B2
2⅞” EUE FSTD-278E-P2 FSTD-278E-B2
EUE
3½” EUE FSTD-312E-P2 FSTD-312E-B2
4½” EUE FSTD-412E-P2 FSTD-412E-B2

Thread
Connection Size Pin Model Box Model
Type
MRP Series External 4½” Buttress FSTD-412B-P2 FSTD-412B-B2
Frame Style Standard 5” Buttress FSTD-5B-P2 FSTD-5B-B2
5½” Buttress FSTD-512B-P2 FSTD-512B-B2
6⅝” Buttress FSTD-658B-P2 FSTD-658B-B2
7” Buttress FSTD-7B-P2 FSTD-7B-B2
7⅝” Buttress FSTD-758B-P2 FSTD-758B-B2
8⅝” Buttress FSTD-858B-P2 FSTD-858B -B2
Buttress
9⅝” Buttress FSTD-958B-P2 FSTD-958B-B2
10¾” Buttress FSTD-1034B-P2 FSTD-1034B-B2
11¾” Buttress FSTD-1134B -P2 FSTD-1134B-B2
13⅜” Buttress FSTD-1338B-P2 FSTD-1338B-B2
16” Buttress FSTD-16B-P2 FSTD-16B-B2
18⅝” Buttress FSTD-1858B-P2 FSTD-1858B-B2
20” Buttress FSTD-20B-P2 FSTD-20B-B2
MRP Series Internal
Frame Style Standard Thread
Connection Size Pin Model Box Model
Type
4½” 8R LTC FSTD-412L-P2 FSTD-412L-B2
5” 8R LTC FSTD-5L-P2 FSTD-5L-B2
5½” 8R LTC FSTD-512L-P2 FSTD-512L-B2
6⅝” 8R LTC FSTD-658L-P2 FSTD-658L-B2
LTC 7” 8R LTC FSTD-7L-P2 FSTD-7L-B2
7⅝” 8R LTC FSTD-758L-P2 FSTD-758L-B2
8⅝” 8R LTC FSTD-858L-P2 FSTD-858L-B2
9⅝” 8R LTC FSTD-958L-P2 FSTD-958L-B2>P110 or FSTD-958L-B2<P110
20” 8R LTC FSTD-20L-P2 FSTD-20L-B2>JK55 or FSTD-20L-B2<JK55
*Standards for Tubing and Casing Connections for MRP-5000 gages are available. Special Orders, Non
Standard API, Round or Premium Connection Setting Standards are available.

108 www.gagemaker.com • [email protected]

Frame Style Setting Standards for MRP-1000, 1500, 2000, 2500, 3000, &
3500 Series* (Cont.)

Thread
Connection Size Pin Model Box Model
Type
4½” - 9.50# 8R STC FSTD-412S-9-P2 FSTD-412S-9-B2
4½” - Other 8R STC FSTD-412S-O-P2 FSTD-412S-O-B2
5” - 11.50# 8R STC FSTD-5S-11-P2 FSTD-5S-O-B2
5” - Other 8R STC FSTD-5S-O-P2 FSTD-5S-O-B2 SSTD-P-LTC
5½” 8R STC FSTD-512S-P2 FSTD-512S-B2
6⅝” 8R STC FSTD-658S-P2 FSTD-658S-B2
7” - 17.00# 8R STC FSTD-7S-17-P2 FSTD-7S-17-B2
7” - Other 8R STC FSTD-7S-O-P2 FSTD-7S-O-B2
7⅝” 8R STC FSTD-758S-P2 FSTD-758S-B2
STC 8⅝”- 24.00# 8R STC FSTD-858S-24-P2 FSTD-858S-24-B2
8⅝” - Other 8R STC FSTD-858S-O-P2 FSTD-858S-O-B2
9⅝” 8R STC FSTD-958S-P2 FSTD-958S-B2>P110 or FSTD-958S-B2<P110
10¾”- 32.75# 8R STC FSTD-1034S-32-P2 FSTD-1034S-32-B2
10¾”- Other 8R STC FSTD-1034S-O-P2 FSTD-1034S-O-B2>P110 or FSTD-1034S-O-B2<P110
11¾” 8R STC FSTD-1134S-P2 FSTD-1134S -B2>P110 or FSTD-1134S-B2<P110
13⅜” 8R STC FSTD-1338S-P2 FSTD-1338S-B2>P110 or FSTD-1338S-B2<P110
16” 8R STC FSTD-16S-P2 FSTD-16S-B2
18⅝” 8R STC FSTD-1858S-P2 FSTD-1858S-B2
20” 8R STC FSTD-20S-P2 FSTD-20S-B2>JK55 or FSTD-20S-B2<JK55 MRP-2000 on pin step
standard
*Standards for Tubing and Casing Connections for MRP-5000 gages are available. Special Orders, Non
Standard API, Round or Premium Connection Setting Standards are available.

Step Style Setting Standards for MRP-1000, 1500, 2000, & 2500 Series
The step style setting standards are designed to preset several models of the MRP Series gages for
accurate inspection of API threaded connections. These standards consist of a rigid, non-adjustable
steel block precision machined to proper size to tolerances of ±.0003”.

Thread Type Connection Sizes Pin Model Box Model

EUE 2⅜” - 4½” SSTD-P-EUE SSTD-B-EUE
NUE 2⅜” - 4½” SSTD-P-NUE SSTD-B-NUE
Line Pipe 2 ½- 10” SSTD-P-LP SSTD-B-LP
LTC 4½” - 9⅝” SSTD-P-LTC SSTD-B-LTC
4½” - 6⅝” SSTD-P-STC1 SSTD-B-STC1
STC 7” - 8⅝” SSTD-P-STC2 SSTD-B-STC2
10¾” - 13⅜” SSTD-P-STC3 SSTD-B-STC3
4½” - 7⅝” SSTD-P-BTC1 SSTD-B-BTC1
Buttress
8⅝” - 13⅜” SSTD-P-BTC2 SSTD-B-BTC2 Pin and Box
Step Standards

Phone: 713-472-7360 • Fax: 713-472-7241 109

 Gagemaker Products

Tapered Thread Functional Size

MRP-5000 Functional Roll Gages for Tapered Threads
MRP-5001
The MRP-5000 series of thread pitch diameter gages use hardened and ground thread rolls to inspect
functional size of tapered threaded connections. The MRP-5000 gages are adjustable within a size
range and have interchangeable thread rolls for inspection of all API thread forms. The gages must
be preset to size using one of a variety of setting methods available. Refer to the setting options that
follow. Please specify preferred taper arms when ordering. Thread rolls and standards are sold
separately.

Model Description Resolution Range

MRP-501* External Sizes by Taper, Single Taper* .0001” 1” - 2¼”
MRP-502* Internal Sizes by Taper, Single Taper* .0001” 1” - 2¼”
MRP-5001 Internal/External Tubing and Casing Connections .0005” 2⅜” - 5½”
MRP-5002 Internal/External Tubing and Casing Connections .0005” 2⅜” - 13⅜”
MRP-5003 Internal/External Tubing and Casing Connections .0005” 13⅜” - 20”
MRP-5004 Internal/External Tubing and Casing Connections .0005” 2⅜” - 9⅝”
*Please specify taper when ordering. Built to one specific taper. One taper per gage. Set of thread rolls included.

MRP-5000 Replacement Parts

MRP-5001
Side View Model Description*
MRP5-10 Positioning Springs (Set of 2)
MRP5-11 Retainer Washers (Set of 2)
MRP5-12 Lock Screws (Set of 2)
MRP5-75T ¾” TPF Taper Arms (Set of 2)
MRP5-10T 1” TPF Taper Arms (Set of 2)
*Taper arm price does not include thread rolls.
To determine the thread rolls required, refer to thread roll chart below.

MRP-5000 MRP-5000 Thread Rolls

Series
Taper Arm The product thread form determines the thread roll set that will be used. Thread roll sets consist of
two rolls supplied in a labeled storage tube.

Model Description
TR-8R All API 8 Round Tubing
TR-10R All API 10 Round Tubing
MRP-502
TR-8LP 8V API Line Pipe
TR-11LP 11½ TPI V API Line Pipe
TR-B10I API Buttress Casing, Internal, 16” - 20”
TR-B10E API Buttress Casing, External, 16” - 20”
TR-B75 API Buttress Casing, 4½” - 13⅜”
TR-BL Blank thread roll set

110 www.gagemaker.com • [email protected]

Frame Style Setting Standards
MRP-5000 Series Setting Standards for Tubing and Casing Connections*
These frame style setting standards are designed to preset MRP-5000 Series gages for accurate
inspection of API threaded connections. These standards consist of a rigid, non-adjustable steel block
precision machined to proper size to tolerances of ±.0003”.

Thread
Connection Size Pin Model Box Model
Type
2⅜” NUE FSTD-238N-P5 FSTD-238N-B5
2⅞” NUE FSTD-278N-P5 FSTD-278N-B5
NUE Setting an MRP-5001 with
3½” NUE FSTD-312N-P5 FSTD-312N-B5 Frame Style Standards
4½” NUE FSTD-412N-P5 FSTD-412N-B5
2⅜” EUE FSTD-238E-P5 FSTD-238E-B5
2⅞” EUE FSTD-278E-P5 FSTD-278E-B5
EUE
3½” EUE FSTD-312E-P5 FSTD-312E-B5
4½” EUE FSTD-412E-P5 FSTD-412E-B5
4½” Buttress FSTD-412B-P5 FSTD-412B-B5
5” Buttress FSTD-5B-P5 FSTD-5B-B5
5½” Buttress FSTD-512B-P5 FSTD-512B-B5
6⅝” Buttress FSTD-658B-P5 FSTD-658B-B5
7” Buttress FSTD-7B-P5 FSTD-7B-B5
7⅝” Buttress FSTD-758B-P5 FSTD-758B-B5
8⅝” Buttress FSTD-858B-P5 FSTD-858B -B5
Buttress
9⅝” Buttress FSTD-958B-P5 FSTD-958B-B5
10¾” Buttress FSTD-1034B-P5 FSTD-1034B-B5
11¾” Buttress FSTD-1134B -P5 FSTD-1134B-B5
13⅜” Buttress FSTD-1338B-P5 FSTD-1338B-B5
16” Buttress FSTD-16B-P5 FSTD-16B-B5 MRP-5000 Frame Style Box Standard
18⅝” Buttress FSTD-1858B-P5 FSTD-1858B-B5
20” Buttress FSTD-20B-P5 FSTD-20B-B5
4½” 8R LTC FSTD-412L-P5 FSTD-412L-B5
5” 8R LTC FSTD-5L-P5 FSTD-5L-B5
5½” 8R LTC FSTD-512L-P5 FSTD-512L-B5
6⅝” 8R LTC FSTD-658L-P5 FSTD-658L-B5
LTC 7” 8R LTC FSTD-7L-P5 FSTD-7L-B5
7⅝” 8R LTC FSTD-758L-P5 FSTD-758L-B5
8⅝” 8R LTC FSTD-858L-P5 FSTD-858L-B5
9⅝” 8R LTC FSTD-958L-P5 FSTD-958L-B5>P110 or FSTD-958L-B5<P110
20” 8R LTC FSTD-20L-P5 FSTD-20L-B5>JK55 or FSTD-20L-B5<JK55
4½” - 9.50# 8R STC FSTD-412S-9-P5 FSTD-412S-9-B5
4½” - Other 8R STC FSTD-412S-O-P5 FSTD-412S-O-B5
5” - 11.50# 8R STC FSTD-5S-11-P5 FSTD-5S-O-B5
5” - Other 8R STC FSTD-5S-O-P5 FSTD-5S-O-B5
5½” 8R STC FSTD-512S-P5 FSTD-512S-B5
6⅝” 8R STC FSTD-658S-P5 FSTD-658S-B5
MRP-5000 Frame Style Pin Standard
7” - 17.00# 8R STC FSTD-7S-17-P5 FSTD-7S-17-B5
7” - Other 8R STC FSTD-7S-O-P5 FSTD-7S-O-B5
7⅝” 8R STC FSTD-758S-P5 FSTD-758S-B5
STC 8⅝”- 24.00# 8R STC FSTD-858S-24-P5 FSTD-858S-24-B5
8⅝” - Other 8R STC FSTD-858S-O-P5 FSTD-858S-O-B5
9⅝” 8R STC FSTD-958S-P5 FSTD-958S-B5>P110 or FSTD-958S-B5<P110
10¾”- 32.75# 8R STC FSTD-1034S-32-P5 FSTD-1034S-32-B5
10¾”- Other 8R STC FSTD-1034S-O-P5 FSTD-1034S-O-B5>P110 or FSTD-1034S-O-B5<P110
11¾” 8R STC FSTD-1134S-P5 FSTD-1134S -B5>P110 or FSTD-1134S-B5<P110
13⅜” 8R STC FSTD-1338S-P5 FSTD-1338S-B5>P110 or FSTD-1338S-B5<P110
16” 8R STC FSTD-16S-P5 FSTD-16S-B5
18⅝” 8R STC FSTD-1858S-P5 FSTD-1858S-B5
20” 8R STC FSTD-20S-P5 FSTD-20S-B5>JK55 or FSTD-20S-B5<JK55
*Rotary Shouldered Connection pin and custom standards are available. Please contact Gagemaker for
more information.

Phone: 713-472-7360 • Fax: 713-472-7241 111

 Gagemaker Products

Pitch Diameter
Pitch Diameter is one of the most important inspections for nearly any thread. In the past, pitch diameter
was ignored as long as the ring or plug gage threaded. Now, using Gagemaker gages, you have more
control over threading connections of marginal quality. The process of locating and measuring the pitch
LPB-4-2-50
diameter takes less than a minute. This minute of inspection quickly decides the difference between
good and bad.

Rotary Shouldered Connection Pitch Diameter Location Profiles

Pitch diameter location templates locate the point on the connection where the pitch diameter is
measured. When applied properly to the connection, the template’s special layout mark indicates the
proper thread to measure the pitch diameter. A simple mark with a felt tip marking pen allows the
LPB-3.5-2-H9 operator or inspector to accurately position the gage and read a diameter. Please specify the threads
per inch (TPI), taper per foot (TPF), and thread form when ordering.
Box Profiles
Model Description
LPB-3-1.25-SLH9 Box Location Profile template for 3 TPI, 1.25 TPF, 90-V-0.084 thread form
LPB-3.5-2-H9 Box Location Profile template for 3.5 TPI, 2 TPF, 90-V-0.050 thread form
LPB-3.5-3-H9 Box Location Profile template for 3.5 TPI, 3 TPF, 90-V-0.050 thread form
LPB-4-1.5-76 Box Location Profile template for 4 TPI, 1.50 TPF, V-0.076 thread form
LPP-3.5-2-H9
LPB-4-2-38 Box Location Profile template for 4 TPI, 2 TPF, V-0.038R thread form
LPB-4-2-50 Box Location Profile template for 4 TPI, 2 TPF, V-0.050 thread form
LPB-4-3-38 Box Location Profile template for 4 TPI, 3 TPF, V-0.038 thread form
LPB-4-3-50 Box Location Profile template for 4 TPI, 3 TPF, V-0.050 thread form
LPB-4-3.375-A094 Box Location Profile template for 4 TPI, 3.375 TPF, A-0.094 thread form
LPB-5-3-40 Box Location Profile template for 5 TPI, 3 TPF, V-0.040 thread form
LPB-6-1.0-55 Box Location Profile template for 6 TPI, 1.0 TPF, V-0.055 thread form
LPP-6-1.5-55
LPB-6-1.5-55 Box Location Profile template for 6 TPI, 1.50 TPF, V-0.055 thread form
LPB-6-2-32 Box Location Profile template for 6 TPI, 2 TPF, V-0.032 thread form

Pin Profiles
Model Description
LPP-3-1.25-SLH9 Pin Location Profile template for 3 TPI, 1.25 TPF, 90-V-0.084 thread form
LPP-3.5-2-H9 Pin Location Profile template for 3.5 TPI, 2 TPF, 90-V-0.050 thread form
LPP-3.5-3-H9 Pin Location Profile template for 3.5 TPI, 3 TPF, 90-V-0.050 thread form
LPP-4-1.5-76 Pin Location Profile template for 4 TPI, 1.50 TPF, V-0.076 thread form
LPP-4-2-38 Pin Location Profile template for 4 TPI, 2 TPF, V-0.038R thread form
LPP-4-2-50 Pin Location Profile template for 4 TPI, 2 TPF, V-0.050 thread form
LPP on a Pin with blue line marking LPP-4-3-38 Pin Location Profile template for 4 TPI, 3 TPF, V-0.038 thread form
proper thread
LPP-4-3-50 Pin Location Profile template for 4 TPI, 3 TPF, V-0.050 thread form
LPP-4-3.375-A094 Pin Location Profile template for 4 TPI, 3.375 TPF, A-0.094 thread form
LPP-5-3-40 Pin Location Profile template for 5 TPI, 3 TPF, V-0.040 thread form
LPP-6-1.0-55 Pin Location Profile template for 6 TPI, 1.0 TPF, V-0.055 thread form
LPP-6-1.5-55 Pin Location Profile template for 6 TPI, 1.50 TPF, -0.055 thread form
LPP-6-2-32 Pin Location Profile template for 6 TPI, 2 TPF, V-0.032 thread form

LPB on a Box cutout

112 www.gagemaker.com • [email protected]

RSC Box Pitch Diameter Gages
Gagemaker’s internal diameter and groove gages measure variation in internal bore diameters. Pitch
diameter gages are shipped with two 0.144” diameter contact points (T144) as standard. Setting
dimensions for the pitch diameter gages are provided by the TDWIN Taper software. Software is
sold separately (see page 129). Refer to page 124 for the proper contact point for your particular
connection.

Model Description Range

IT-5104-RSC Internal Diameter/Groove Gage, 4” (101.6 mm) Depth 1½” - 10” (38.1 mm - 254 mm) Dia.
IT-5104-04 Replacement Lower Arm 4¼” (107.9 mm) Length
IT-5104-RSC
RSC Pin Pitch Diameter Gages
The ball pitch diameter gages gages indicate the pitch diameter size of the product’s external thread.
The gages are adjustable within a size range and use interchangeable contact points to measure
different pitch threads. Gages are shipped with two 0.144” diameter contact points (T144) as
standard. Reference page 124 for other connection specific contact points.

Model Description Range

PD-8001-RSC External Ball Pitch Diameter Gage 0” - 6” (0 mm - 152.4 mm)
PD-8002-RSC External Ball Pitch Diameter Gage 6” - 12” (152.4 mm - 304.8 mm)

Rod Style Setting Standards

Rod style setting standards are used to set many JSS gages. Specify size or specific connection
when ordering. Ex.: RS-3.5-DS-B, RS-NC77-B, RS-2.375-REG-B.

Model Description
RS-__-DS-B Rod Standard for Double Streamline (3.5" - 5.5"), Box PD-8001-RSC
RS-__-DS-P Rod Standard for Double Streamline (3.5" - 5.5"), Pin
RS-__-EF-B Rod Standard for External Flush (2.375" - 4.5"), Box
RS-__-EF-P Rod Standard for External Flush (2.375" - 4.5"), Pin
RS-__-FH-B Rod Standard for Full Hole (2.875" - 6.625"), Box
RS-__-FH-P Rod Standard for Full Hole (2.875" - 6.625"), Pin
RS-__-H9-B Rod Standard for H-90 (3.5" - 8.625"), Box
RS-__-H9-P Rod Standard for H-90 (3.5" - 8.625"), Pin
RS-__-IF-B Rod Standard for Internal Flush (2.375" - 6.625"), Box
RS-__-IF-P Rod Standard for Internal Flush (2.375" - 6.625"), Pin
RS-NC__-B Rod Standard for API Numbered Connections (#10 - #77), Box
RS-NC__-P Rod Standard for API Numbered Connections (#10 - #77), Pin
RS-___-OH-B Rod Standard for Open Hole (2.375" - 4.5"), Box
RS-___-OH-P Rod Standard for Open Hole (2.375" - 4.5"), Pin
RS-__-PAC-B Rod Standard for PAC (2.375" - 3.5"), Box
RS-__-PAC-P Rod Standard for PAC (2.375" - 3.5"), Pin
RS-__-SH-B Rod Standard for Slim Hole (2.375" - 4.5"), Box
RS-__-SH-P Rod Standard for Slim Hole (2.375" - 4.5"), Pin
RS-__-SLH9-B Rod Standard for Slimline H-90 (2.375" - 3.5"), Box
RS-__-SLH9-P Rod Standard for Slimline H-90 (2.375" - 3.5"), Pin
RS-__-REG-B Rod Standard for Regular (1.0" - 8.625"), Box
RS-__-REG-P Rod Standard for Regular (1.0" - 8.625"), Pin
RS-__-XH-B Rod Standard for Xtra Hole (2.875" - 5.0"), Box
RS-__-XH-P Rod Standard for Xtra Hole (2.875" - 5.0"), Pin
RS-__-WO-B Rod Standard for Wide Open (2.375" - 4.5"), Pin
RS-__-WO-P Rod Standard for Wide Open (2.375" - 4.5"), Pin Setting PD-8001-RSC with Rod Standard

Phone: 713-472-7360 • Fax: 713-472-7241 113

 Gagemaker Products

Straight Thread External Pitch Diameter Gages (0” to 72” Diameters)

The ball pitch diameter gages or “GO/NO GO” gages indicate the pitch diameter size of the product’s
external thread. The gages are adjustable within a size range and use interchangeable contact points
to measure different pitch threads. Setting dimensions for the pitch diameter gages are provided by
the TDWIN software. Software (see page 128) and contact points (see pages 124-125) are sold
PD-8001
separately. Indicators have a ½” travel and .0005” resolution, and higher resolutions are available.
Models PD-8004 through PD-8016 include a custom wood case.

Model Description Range

PD-8000 External Ball Pitch Diameter Gage 0” - 2⅜” (0 mm - 60.3 mm)
PD-8001 External Ball Pitch Diameter Gage 0” - 6” (0 mm - 152.4 mm)
PD-8002 External Ball Pitch Diameter Gage 6” - 12” (152.4 mm - 304.8 mm)
PD-8004 External Ball Pitch Diameter Gage 12” - 16” (304.8 mm - 406.4 mm)
PD-8006 External Ball Pitch Diameter Gage 16” - 20” (406.4 mm - 508 mm)
PD-8008 External Ball Pitch Diameter Gage 20” - 24” (508 mm - 609.6 mm)
PD-8010 External Ball Pitch Diameter Gage 24” - 28” (609.6 mm 711.2 mm)
PD-8012 External Ball Pitch Diameter Gage 28” - 36” (711.2 mm - 914.4 mm)
PD-8013 External Ball Pitch Diameter Gage 36” - 44” (914.4 mm - 1117.6 mm)
PD-8014 External Ball Pitch Diameter Gage 44” - 52” (1117.6 mm - 1320.8 mm)
PD-8015 External Ball Pitch Diameter Gage 52” - 60” (1320.8 mm - 1524.0 mm)
PD-8016 External Ball Pitch Diameter Gage 60” - 72” (1524.0 mm - 1828.8 mm)

Straight Thread Internal Pitch Diameter Gages (1½” to 27” Diameters)

The ball pitch diameter gages or “GO/NO GO” gages indicate the pitch diameter size of the product’s
internal threads. The gages are adjustable within a size range and use interchangeable contact
PD-6000
points to measure different pitch threads. Setting dimensions for the pitch diameter gages are
provided by the TDWIN software (sold separately, see page 128). Higher resolution indicators are
available. All of the PD-6000 series are sold without contact points. See pages 124-125 for contact
points.

Model Description Travel Resolution Range

PD-6000 Internal Pitch Diameter Gage (“V” & Acme) ½" .0005" 1½” - 9”
PD-6000-07 Replacement Arm Set 4½” length
PD-6001 Internal Pitch Diameter Gage ½" .0005" 6” - 24”

PD-6001 Replacement Parts (Extensions have #10-32 threads)

Model Description Length
PD-6001-PD4M Cap
4-2-617 Indicator Base - Mitutoyo Indicator Only
PD-6001-CBA Cap and Base Assembly
PD-6001-PD3 Adjustment Cap Lock Nut
PD-6001-PD2 Adjustment Cap
PD-6001-PD1 Contact Point Adapter
PD-6001-PDA Extension Rod .430”
PD-6001-PDB Extension Rod .860”
PD-6001-PDC Extension Rod 1.290”
PD-6001-PDD Extension Rod 1.720”
PD-6001-PDE Extension Rod 3.440”
PD-6001-PDF Extension Rod 5.590”
PD-6001 and Extension Rods PD-6001-PDG Extension Rod 7.740”
PD-6001-PDH Extension Rod 10.320”
PD-6001-12E PD-6001 Internal Pitch Diameter Extension Rod 12”
PD-6001-24E PD-6001 Internal Pitch Diameter Extension Rod 24”
PD-6001-36E PD-6001 Internal Pitch Diameter Extension Rod 36”

114 www.gagemaker.com • [email protected]

Thread Taper
External Taper Gages
Gagemaker’s external taper gages inspect variation in connection taper. External taper gages are
shipped with .072” diameter contact points as standard. Refer to page 124 for the proper contact point
for your particular connection. All indicators are .001” resolution, but higher resolution indicators are
available for some models.
ET-7001
Model Description Range Model Description Range
ET-7001 External Taper, ½” travel 0” - 6” ET-7005 External Taper, 1” travel 0” - 16”
ET-7002 External Taper, ½” travel 0” - 10” ET-7006 External Taper, ½” travel 16” - 24”
ET-7003 External Taper, 1” travel 0” - 10” ET-7007 External Taper, 1” travel 16” - 24”
ET-7004 External Taper, ½” travel 0” - 16”

Internal Taper Gages

Gagemaker’s internal taper gages measure variation in connection taper. Taper gages are shipped
with our standard set of .072” diameter contact points (T072), unless specified otherwise. Refer to
the contact point page 124 for the proper contact points for your particular connections. IT-6001
includes one set of extension rods up to 13⅜”. Higher resolution indicators are available.

Model Description Range Travel Resolution

IT-6000 Internal Taper Gage 4¼” Depth, 1½” - 9” Diameter 1” .001”
IT-6001 Internal Taper Gage Any Depth, 5” - 13⅜" API Sizes ½” .001”
IT-6001-VM Internal Taper Gage Any Depth, 3½” Diameter ¼” .001”

IT-6000 Replacement Parts

Model Description Length
IT-6000-07 Replacement Arm Set 4¼”
IT-6000
IT-6001 Replacement Parts (Extensions have #10-40 threads)
Model Description Length Model Description Length
Cap- Mitutoyo Extension rod,
IT-6001-01M - IT-6001-13 4.643”
Indicator 9⅝” Connection
Extension rod,
IT-6001-04 Point Adapter .062” IT-6001-14 5.768”
10¾” Connection
Extension rod, Extension rod,
IT-6001-06 .200” IT-6001-15 6.768”
5” Connection 11¾” Connection
Extension rod, Extension rod,
IT-6001-07 .523” IT-6001-16 8.393”
5½” Connection 13⅜” Connection
Extension rod, Extension rod,
IT-6001-09 1.643” IT-6001-17 11.018"
6⅝” Connection 16” Connection
Extension rod, Extension rod,
IT-6001-10 2.023” IT-6001-18 13.643"
7” Connection 18⅝” Connection
Extension rod, Extension rod,
IT-6001-11 2.643” IT-6001-19 15.018"
7⅝” Connection 20" Connection
Extension rod,
IT-6001-12 3.643”
8⅝” Connection
IT-6001 and
Extension Rods
IT-6001-VM Replacement Parts
Model Description Minimum Bore
IT-6001-01-VM Short Cap 3.4275"

Phone: 713-472-7360 • Fax: 713-472-7241 115

 Gagemaker Products

Functional Size
RG-7001 External Functional Size Thread Inspection Gages ( ⅝” to 24” Diameters)
These functional thread inspection, or “GO/NO GO” gages, measure external thread diameters. The
gages are adjustable within a size range and use interchangeable thread rolls to measure different pitch
threads. Setting dimensions for the functional pitch diameter gages are provided by the TDWIN Thread
Disk software. The software (see page 129) and thread rolls (see page 117) are sold separately.
Indicators have a ½”travel and .0005” resolution, and higher resolutions are available.

Model Description Range

RG-7000 External Thread Roll Gage ⅝” - 4” (15.9 mm - 101.6 mm)
RG-7001 External Thread Roll Gage 4” - 8” (101.6 mm - 203.2 mm)
RG-7002 External Thread Roll Gage 8” - 12” (203.2 mm - 304.8 mm)
RG-7003 External Thread Roll Gage 12” - 16” (304.8 mm - 406.4 mm)
RG-7004 External Thread Roll Gage 16” - 20” (406.4 mm - 508 mm)
RG-7005 External Thread Roll Gage 20” - 24” (508 mm - 609.6 mm)
RG-LAA Lower Adjustment Arm

Internal Functional SIze Thread Inspection Gages (1½” to 24” Diameters)

Gagemaker also manufactures functional thread inspection gages that inspect internal threads. The
gages are adjustable within a size range and use interchangeable thread rolls to measure different
PG-6000 Series
pitch threads. Indicators have a ½”travel and .0005” resolution, and higher resolutions are available.
Thread roll sets not included. See page 117 for thread rolls.

Model Description Range

PG-6000 Internal Thread Roll Gage, 2½” reach 1½” - 9” (38 mm - 228.6 mm)
PG-6001 Internal Thread Roll Gage, 2½” reach 9” - 16” (228.6 mm - 406.4 mm)
PG-6002 Internal Thread Roll Gage, 2½” reach 16” - 24” (406.4 mm - 609.6 mm)
PG-6003 Internal Thread Roll Gage, 2½” reach 24" - 32" (609.6 mm - 812.8 mm)
PG-6000-SA Replacement Arm Set 2½” reach
PG-6000-XA Extended Reach Arm Set 4½” reach
PG-6000-17 Locking T-nut for Arms

Deep Bore Internal Functional Size

The DPG-6000 gage inspects diameters of internal threads using thread rolls. This functional diameter
gage inspects the effects of all thread element variations and reports any deviations. All thread rolls
are sold separately. See page 117 for thread rolls.

Model Description Range

Deep bore thread roll gage assembly for 4 pitch and
DPG-6000 3” - 4.300” dia., 6” Reach
finer threads only.
DPG-6R Handle Extension Assemblies 6” Reach
DPG-8R Handle Extension Assemblies 8” Reach
DPG-12R Handle Extension Assemblies 12” Reach
DPG-6000 DPG-18R Handle Extension Assemblies 18” Reach
DPG-24R Handle Extension Assemblies 24” Reach
DPG-1 Diameter Extension Arms 3” to 4.300” dia.
DPG-2 Diameter Extension Arms 4.300” to 5.100” dia.
DPG-3 Diameter Extension Arms 5.100” to 5.900” dia.
DPG-4 Diameter Extension Arms 5.900” to 6.700” dia.
DPG-5 Diameter Extension Arms 6.700” to 7.500” dia.
DPG-6 Diameter Extension Arms 7.500” to 8.300” dia.
DPG-7 Diameter Extension Arms 8.300” to 9.100” dia.

116 www.gagemaker.com • [email protected]

Thread Rolls
Gagemaker thread rolls are sold in matched sets of two rolls. Specify the pitch of the thread when
ordering.

UN Series Thread Rolls

“TRV” thread rolls inspect the functional fit of machine threaded parts with 60° “V” thread forms. These thread rolls are designed
specifically for internal or external applications.
Internal Thread Diameters (1½” & Larger) External Thread Diameters (1½” & Larger)
Model Description Model Description
TRVI-4P 4 pitch internal 60° “V” TRVE-4P 4 pitch external 60° “V”
TRVI-5P 5 pitch internal 60° “V” TRVE-5P 5 pitch external 60° “V”
TRVI-6P 6 pitch internal 60° “V” TRVE-6P 6 pitch external 60° “V”
TRVI-8P 8 pitch internal 60° “V” TRVE-8P 8 pitch external 60° “V”
TRVI-10P 10 pitch internal 60° “V” TRVE-10P 10 pitch external 60° “V”
TRVI-12P 12 pitch internal 60° “V” TRVE-12P 12 pitch external 60° “V”
TRVI-14P 14 pitch internal 60° “V” TRVE-14P 14 pitch external 60° “V”
TRVI-16P 16 pitch internal 60° “V” TRVE-16P 16 pitch external 60° “V”
TRVI-18P 18 pitch internal 60° “V” TRVE-18P 18 pitch external 60° “V”
TRVI-20P 20 pitch internal 60° “V” TRVE-20P 20 pitch external 60° “V”

Acme and Stub Acme Thread Rolls

“TRA” and “TRSA” thread rolls inspect the functional fit of parts with 29° Acme and Stub Acme thread forms.
Acme Thread Diameters (1½” & Larger) Stub Acme Thread Diameters (1½” & Larger)
Model Description Model Description
TRA-2P 2 pitch 29° Acme TRSA-2P 2 pitch 29° Stub Acme
TRA-3P 3 pitch 29° Acme TRSA-3P 3 pitch 29° Stub Acme
TRA-4P 4 pitch 29° Acme TRSA-4P 4 pitch 29° Stub Acme
TRA-5P 5 pitch 29° Acme TRSA-5P 5 pitch 29° Stub Acme
TRA-6P 6 pitch 29° Acme TRSA-6P 6 pitch 29° Stub Acme
TRA-8P 8 pitch 29° Acme TRSA-8P 8 pitch 29° Stub Acme
TRA-10P 10 pitch 29° Acme TRSA-10P 10 pitch 29° Stub Acme
TRA-12P 12 pitch 29°Acme TRSA-12P 12 pitch 29° Stub Acme
TRA-14P 14 pitch 29° Acme TRSA-14P 14 pitch 29° Stub Acme
TRA-16P 16 pitch 29° Acme TRSA-16P 16 pitch 29° Stub Acme
TRA-18P 18 pitch 29° Acme TRSA-18P 18 pitch 29° Stub Acme

ISO Metric Series Thread Rolls

“TRM” thread rolls inspect the functional fit of machine threaded parts with ISO Metric 60° “V” thread forms.
Internal Thread Diameters (38.1mm & Larger) External Thread Diameters (38.1mm & Larger)
Model Description Model Description
TRMI-4P 4 mm pitch internal 60° “V” TRME-4P 4 mm pitch external 60° "V”
TRMI-3.5P 3.5 mm pitch internal 60° “V” TRME-3.5P 3.5 mm pitch external 60° “V”
TRMI-3P 3 mm pitch internal 60° “V” TRME-3P 3 mm pitch external 60° “V”
TRMI-2.5P 2.5 mm pitch internal 60° “V” TRME-2.5P 2.5 mm pitch external 60° “V”
TRMI-2P 2 mm pitch internal 60° “V” TRME-2P 2 mm pitch external 60° “V”
TRMI-1.75P 1.75 mm pitch internal 60° "V” TRME-1.75P 1.75 mm pitch external 60° “V”
TRMI-1.5P 1.5 mm pitch internal 60° “V” TRME-1.5P 1.5 mm pitch external 60° “V”
TRME-1P 1 mm pitch external 60° “V”

National 7° X 45° Buttress Series Thread Rolls

“TRB” thread rolls inspect the functional fit of machine threaded parts with 7° X 45° Buttress thread forms.
Thread Diameter (1½” & Larger) Assorted
Thread Rolls
Model Description Model Description
TRB745-2P 2 pitch 7° X 45° Buttress TRB745-8P 8 pitch 7°X 45° Buttress
TRB745-3P 3 pitch 7° X 45° Buttress TRB745-10P 10 pitch 7°X 45° Buttress
TRB745-3.5P 3.5 pitch 7° X 45° Buttress TRB745-12P 12 pitch 7° X 45° Buttress
TRB745-4P 4 pitch 7° X 45° Buttress TRB745-16P 16 pitch 7° X 45° Buttress
TRB745-6P 6 pitch 7° X 45° Buttress

Trapezoidal Thread Rolls

"TRT" thread rolls inspect the functional fit of machine thread parts with trapezoidal thread forms.
Thread Diameter (38.1 mm & Larger)
Model Description Model Description Model Description
TRT-2P 2 mm pitch Trapezoidal TRT-5P 5 mm pitch Trapezoidal TRT-9P 9 mm pitch Trapezoidal
TRT-3P 3 mm pitch Trapezoidal TRT-6P 6 mm pitch Trapezoidal TRT-10P 10 mm pitch Trapezoidal
TRT-4P 4 mm pitch Trapezoidal TRT-8P 8 mm pitch Trapezoidal TRT-12P 12 mm pitch Trapezoidal
Specials- All other thread forms- Available Prices Available Upon Request

Phone: 713-472-7360 • Fax: 713-472-7241 117

 Gagemaker Products

Small Diameters
Small Internal Diameter Thread Inspection Gages
SPG-6000 with
thread rolls
⅝” (.625) to 1½” (1.500) Diameters
The SPG-6000 line of thread inspection gages measures internal thread diameters smaller than
1.500”. The SPG-6000 can be equipped with either thread rolls or contact points. Contact points are
used to measure pitch diameter, while thread rolls are used in measuring functional size. Contact
points, contact point arms, software, and thread rolls sold separately.

Model Description Range

⅝” - 1½”
SPG-6000 Internal Pitch Diameter Gage, 1” reach
(15.9 mm - 38.1 mm)

Small Internal Diameter UN Series Thread Rolls

“SRV” thread rolls inspect the interanl functional size of machine threaded parts with 60° “V” thread
forms. These thread rolls are designed specifically for internal applications. Rolls are sold in matched
sets (2 rolls). Rolls sold separately from gages and software. Please specify the pitch of thread
when ordering.

Internal Thread Diameters

(.750” to 1.500”)
Model Pitch Model PItch
SRVI-6P 6 pitch internal 60° “V” SRVI-14P 14 pitch internal 60° “V”
SRVI-7P 7 pitch internal 60° “V” SRVI-16P 16 pitch internal 60° “V”
SRVI-8P 8 pitch internal 60° “V” SRVI-18P 18 pitch internal 60° “V”
SRVI-9P 9 pitch internal 60° “V” SRVI-20P 20 pitch internal 60° “V”
SRVI-10P 10 pitch internal 60° “V” SRVI-24P 24 pitch internal 60° “V”
SRVI-11P 11 pitch internal 60° “V” SRVI-28P 28 pitch internal 60° “V”
SRVI-12P 12 pitch internal 60° “V” SRVI-32P 32 pitch internal 60° “V”
SRVI-13P 13 pitch internal 60° “V”

Small Internal Diameter ISO Metric Thread Rolls

“SRM” thread rolls inspect the internal functional size of machine threaded parts with 60° “V” thread
forms. These thread rolls are designed specifically for internal applications. Rolls are sold in matched
sets (2 rolls). Rolls sold separately from gages and software. Please specify the pitch of thread
when ordering.

Internal Thread Diameters

(.750” to 1.500”)
Model Pitch
SRMI-4P 4 mm
SRMI-35P 3.5 mm
SPG Thread Rolls SRMI-3P 3 mm
SRMI-25P 2.5 mm
SRMI-2P 2 mm
SRMI-175P 1.75 mm
SRMI-15P 1.5 mm
SRMI-1P 1 mm

118 www.gagemaker.com • [email protected]

Small Diameter Contact Point Arms
“SPA” contact point arms hold “SP” straight shank contact points on the SPG-6000 for small internal
pitch diameter measurements. Sold separately from gage as a set of 2. Contact points are not SPG-6000 with
included, see chart below. Custom sizes are available, contact customer service for more information. contact points

Model Description Reach Min. Bore

SPA-265 Contact point arms, .265” Diameter 1” Long .700”
SPA-375 Contact point arms, .375” Diameter 1.25” Long .950”
SPA-437 Contact point arms, .437” Diameter 1.50” Long 1.100”

Small Diameter Contact Points

Gagemaker’s SP straight shank contact points are manufactured with carbide balls. Standard contact
diameters are held to tolerances of + .0002”. “SP” contact points fit “SPA” contact point arms only.
Contact point sizes are matched closely to thread inspection wire sizes. These contact point sizes
are used in the TDWIN software program (sold separately). Contact points sold individually and
separately. Contact point arms are not included.

UN, UNJ, and UNR Series Contact Points

Model Thread Pitch Model Thread Pitch

SP-105 5 pitch SP-050 11.5 - 12 pitch
SP-096 6 - 7 pitch SP-041 13 - 16 pitch
SP-072 8 - 9 pitch SP-032 18 - 20 pitch
SP-057 10 pitch

Acme, Stub Acme, and Stub Acme Mod-1 & -2 Contact Points

Model Thread Pitch Model Thread Pitch

SP-105T 5 pitch SP-050T 10 pitch
SP-090T 6 pitch SP-041T 12 - 14 pitch
SP-062T 8 pitch SP-032T 16 pitch

Metric and MJ Series Contact Points

Model Thread Pitch Model Thread Pitch

SP-105 4.5 - 4.75 mm SP-057 2.5 mm
SP-096 4 - 4.25 mm SP-041 1.5 - 2 mm
SP-072 3 - 3.5 mm SP-032 1 - 1.25 mm SPA Contact Point Arms

Small Diameter Contact Point Arms for Threaded Contact Points

“STPA” contact point arms hold threaded contact points on the SPG-6000 for small internal pitch SPA Contact Points
diameter measurements. Sold as a set of 2. Gage, software, and contact points are not included. For
contact points, see pages 124-125. Custom sizes are available, contact customer service for more
information.

Model Description Reach Min. Bore

STPA-375 Threaded contact point arms, .375” Diameter 1.25” Long 1.032”
STPA-437 Threaded contact point arms, .437” Diameter 1.50” Long 1.152”
STPA Contact Point Arms

Phone: 713-472-7360 • Fax: 713-472-7241 119

 Gagemaker Products

Thread Lead
Lead Gages
The lead gage inspects t thread leads using contact points that seat in the threads of a part. Thread lead
is the distance between threads, measured on a plane parallel to the centerline of the threaded part. The
pitch of the thread determines the diameter of the contact points required for taking measurements. API
Specification 7-2 requires thread lead inspection.

The LG-5001 and the LG-5002 use a two-point system to inspect thread lead for straight and tapered
threads. The LG-5001 inspects external threads, while the LG-5002 inspects both external and internal
threads. The two point system allows for a sweeping action to obtain the measurement.

The LG-5003 uses the three-point system to inspect internal and external thread lead. Two fixed contact
points at the rear of the gage and one moveable contact point at the front of the gage provide complete
stability when taking thread lead measurements. This unique design does not require sweeping to obtain
measurements.

Contact points can be easily changed to allow the gage to be used on a variety of thread forms.

Before inspecting parts, the lead gage must be preset to a nominal predetermined dimension using
LG-5002
a lead gage setting standard. Lead standards are available for both straight and tapered threads. Our
setting standards are manufactured according to ANSI and API specifications, respectively.

Please see pages 124-125 for contact points. See page 121 for standards.

Features

• Uses a three-point system for greater stability when inspecting parts (LG-5003).
• Uses interchangeable contact points to allow inspection on a variety of thread forms.
• Requires presetting using Gagemaker’s lead gage setting standards.

Model Description Minimum Bore Range

LG-5003 LG-5001 External Lead Gage 2-point 1.200 ½” - 2” Thread Length

External Lead Gage 2-point, .0001"

LG-5001-1 1.200 ½” - 2” Thread Length
grad. indicator

LG-5002 Lead Gage 2-point 1.200 ½” - 4” Thread Length

Lead Gage 2-point, .0001" grad.

LG-5002-1 1.200 ½” - 4” Thread Length
indicator
Lead Gage 3-point
LG-5003 1.340 ½” - 4” Thread Length
Contact point spacing .500"

Lead Gage 3-point, .0001" grad.

LG-5003-L LG-5003-1 1.340 ½” - 4” Thread Length
indicator, Contact point spacing .500"

Lead Gage 3-point, Contact point

LG-5003-J 1.340 ½” - 4” Thread Length
spacing .193"
Lead Gage 3-point, .0001" grad.,
LG-5003-1J 1.340 ½” - 4” Thread Length
Contact point spacing .193"
LG-5003-L Special Load-to-Load lead gage 1.500 ½” - 4” Thread Length
LG-5003-S Special Stab-to-Stab lead gage 1.500 ½” - 4” Thread Length

120 www.gagemaker.com • [email protected]

Lead Gage Setting Standards
Gagemaker’s precision lead gage setting standards are manufactured in accordance with ANSI
Specifications, API Specification 5B, and API Specification 7-2. Lead gage standards are used to set
the gage prior to inspection.

Model Connection Type/Description TPF* TPI*

LS-1005
API 8-Round Casing, Tubing & Drill Pipe,
LS-1001 ¾” 8 & 10
All 10-Round Tubing
LS-1002 Straight Threads, 6 - 18 Pitch, 4” Length Straight 8 & 10
LS-1003 11½” “V” API Line Pipe ¾” 11½
LS-1004 Straight threads, Line pipe Straight 11½
LS-1005 API Buttress Casing, Internal/External 4½” - 13⅜” ¾” 5
LS-1006 API Buttress Casing, Internal/External 16” - Larger 1” 5

6⅝” API Reg

4”, 5½”, & 6⅝” API Full Hole
LS-5001
2⅞”, 3½” - 5” Hughes Xtra Hole
LS-1007 2” 4
2⅜”, 2⅞” - 4½” Hughes Slim Hole
2⅜” - 5½” API INT Flush
API Numbered Connections #23-#50

5½”, 7⅝” - 8⅝” API Reg

LS-1008 3” 4
API Numbered Connections #56 - #77
2⅜” - 4½” API Reg
LS-1009 3” 5
3½”, 4½” API Full Hole
API Numbered Connections #10, #12, #13, #16
M.T. (Macaroni Tubing) LS-5002
LS-1010 1½” 4
2⅜” - 3½” PAC
2⅜” - 4” American Open Hole
LS-1011 3½” - 6⅝” Hughes H-90 2” 3½
LS-1012 7”- 8⅝” Hughes H-90 3” 3½
LS-1013 2⅜” - 3½” Slim Line H-90 1¼” 3
LS-5001 Straight Threads, 1-5 pitch, 4” length
LS-5002 Straight Threads, 6-18 pitch, 4” length
*TPF = Taper Per Foot, TPI = Threads Per Inch

Lead is measured in one inch intervals. As shown below, the cumulative

lead interval is the total measured distance from the first to the last thread.

LG-5002 in Last and First Position Cumulative

Phone: 713-472-7360 • Fax: 713-472-7241 121

 Gagemaker Products

Thread Height
External Thread Height Gages
Gagemaker manufactures many models of external thread height gages. Specify the type of thread
TH-3001V when ordering. Contact point listed in description (e.g. T072) is included, but may specify other.
See page 123 for standards and contact points.

Model Description Connection Travel Min. Bore

TH-3002B* External Thread Height, 0-25-0, T072 ¾” TPF Buttress .094" 2.930"
External Thread Height, 0-25-0, Step
TH-3003B* 1” TPF Buttress .094" 2.930"
Base, T072
TH-3002BB External Thread Height Base Only ¾” TPF Buttress
TH-3003BB External Thread Height Base Only 1” TPF Buttress
TH-3001R External Thread Height, 0-100, T501 8-Round .162" 3.400"
TH-3002R* External Thread Height, 0-50-0, T501 8-Round .162" 3.400"
TH-3002RB External Thread Height Base Only 8-Round
External Thread Height, 0-25-0, Rotary Shouldered
TH-3000-RSC* .196" 3.230"
T072** Connection/Tool Joint
TH-3001S External Thread Height, 0-100, T072 8-Round .196" 3.230"
TH-3001R
Line Pipe, UN/UNJ/
UNR, Acme, Stub
Acme, Stub Acme
TH-3001V External Thread Height, 0-100, T500C Modified I and II, .196" 3.230"
Metric M & MJ, 7º X
45º Buttress, General
Purpose Pipe Threads
TH-3002V* External Thread Height, 0-50-0, T500C Line Pipe/Tool Joint .196" 3.230"
TH-3002VB External Thread Height Base Only Line Pipe/Tool Joint
*Gage requires a standard for setting before inspection.
**Also ships with either T034 or T044 depending on the connection, please specify when ordering.

Internal Thread Height Gages

Gagemaker also manufactures several models of internal thread height gages. Please specify the
type of thread when ordering. Contact point listed in description (e.g. T072) is included, but may
specify other. See page 123 for standards and contact points.

Model Description Connection Travel Min. Bore

Internal Thread Height, 0-25-0,
TH-3004* Line Pipe .105" 1.575"
T500C
Internal Thread Height, 0-25-0,
TH-3006* 8-Round .105" 1.595"
TH-3002B T502/T503
Internal Thread Height, 0-25-0,
TH-3008* 8-Round .094" 1.575"
T502/T503
Internal Thread Height, 0-25-0,
TH-3009* ¾” TPF Buttress .250" 1.750"
T072
Internal Thread Height, 0-25-0, Rotary Shouldered
TH-3009-RSC* .250" 1.750"
1” Base, T072** Connections
Line Pipe, UN/UNJ/UNR,
Acme, Stub Acme, Stub Acme
Internal Thread Height, 0-100,
TH-3010 Modified I and II, Metric M & .250" 1.750"
1” Base Length (TPD), T500
MJ, 7º X 45º Buttress, General
Purpose Pipe Threads
TH-3012* Internal Thread Height, 0-25-0 ¾” - 2” NPT, AMT .090" .750"
*Gage requires a standard for setting before inspection.
**Also ships with either T034 or T044 depending on the connection, please specify when ordering.

122 www.gagemaker.com • [email protected]

Thread Height Gage Standards
Gagemaker manufactures precision setting standards for presetting thread height gages. Please TH-3008
specify the type of thread when ordering. Custom or special standards are available, contact customer
service for more information.

Model Description
1014 8 & 10 Round Threads

1014S 8 & 10 Round Threads (crest to Pitchline “Shave”)

1015 8 & 11½ Pitch “V” Threads TH-3009

1017 13⅜” & Smaller Buttress, ¾” TPF

1018 16” & Larger Buttress, 1”TPF

10322-RS V-0.032, 2 TPF Rotary Shouldered Connections, 6 TPI to be used with T034 pt.

10382-RS V-0.038, 2 TPF Rotary Shouldered Connections, 4 TPI to be used with T072 pt. TH-3010

10383-RS V-0.038, 3 TPF Rotary Shouldered Connections, 4 TPI to be used with T072 pt.

10403-RS V-0.040, 3 TPF Rotary Shouldered Connections, 5 TPI to be used with T034 pt.

10502-RS V-0.050, 2 TPF Rotary Shouldered Connections, 4 TPI to be used with T044 pt.

10503-RS V-0.050, 3 TPF Rotary Shouldered Connections, 4 TPI to be used with T044 pt.

10551.5-RS V-0.055, 1.5 TPF Rotary Shouldered Connections, 6 TPI to be used with T072 pt.
TH-3004
10761.5-RS V-0.076, 1.5 TPF Rotary Shouldered Connections, 4 TPI to be used with T044 pt.

10H90-2 2” TPF H-90 Connection (90-V-0.050), 3.5 TPI to be used with T072 pt.

10H90-3 3” TPF H-90 Connection (90-V-0.050), 3.5 TPI to be used with T072 pt.

SL-H90 1¼" TPF, 3 TPI, 90-V-0.084 to be used with T072 pt.

Thread Height Gage Contact Points TH-3006

Model Description

T072 0.072” Contact Point for Buttress Threads, RSC Thread Forms V-0.038R & V-0.055

T044 0.044” Contact Point Rotary Shouldered Connection V-0.050 and V-0.076 thread forms

T034 0.034” Contact Point Rotary Shouldered Connection V-0.032 and V-0.040 thread forms TH-3012

T500C 50° Cone Contact Point, “V” Threads for TH-3001V, TH-3002V, & and TH-3004 Gages

T500C-USS Modified 50° Cone Contact Point, USS Improved Buttress

T501 50° Cone Contact Point, Self-Centering for TH-3001R and TH-3002R Gages

T502 Self-Centering Sleeve for T501 & T503 Contact Points

T503 50° Cone Contact Point, “V” Threads for TH-3006

E-Line .063” R Extreme Line Contact Point

Thread Height Standards

Phone: 713-472-7360 • Fax: 713-472-7241 123

 Gagemaker Products

Straight Shank Contact Points

Contact Points
API Contact Points for Lead and Taper Gages
Gagemaker’s standard contact points are manufactured with carbide balls. Both threaded and straight
(non-threaded) shanks are available. All Gagemaker’s inspection gages use threaded shank contact
points. Threaded shanks are #4-48 UNF. Metric threads are available upon request. Most gages
require two contact points.
Straight Threaded Point Threads
Connection Type
Shank Model Shank Model Diameter Per Inch
S235 T235 0.235” 3 Hughes Slim Line H-90
S200 T200 0.200” 3½ All Hughes H-90
S144 T144 0.144” 4 API Rotary Shouldered Connections
T501 and T502
Assembly
S128 T128 0.128” 4½ API Rotary Shouldered Connections
S115 T115 0.115” 5 API Rotary Shouldered Connections
S105T T105T 0.105” 5½ Truncated for Extreme Line
S096 T096 0.096” 6 API Rotary Shouldered Connections
S090 T090 0.090” 5 Buttress Casing – Taper
S072 T072 0.072” 8 API Tubing and Casing
S062 T062 0.062” 5 Buttress Casing – Lead
S057 T057 0.057” 10 API Tubing and Line Pipe
S050 T050 0.050” 11½ API Line Pipe
- T044 0.044” 4 RSC Thread Depth Only
T503 S041 T041 0.041” 14 API Line Pipe
T501
- T034 0.034” 5 RSC Thread Depth Only
T502 S032 T032 0.032” 18 API Line Pipe
S021 T021 0.021” 27 API Line Pipe

Special Application Contact Points

PA-45 Gagemaker continually develops new application contacts and indicator accessories. The following
with items are in stock for immediate delivery. These contact points have #4-48 UNF threaded shank.
contact point
RC-375
All contact points are carbide. Special and metric diameters are available, please call for quotation.
(sold
Straight Shanks are available for T060, T098, and T156.
separately)
Model Ball Dia. Model Ball Dia. Model Ball Dia. Model Ball Dia.
T028 .028" T100 .100” T176 .176" T375 .375”
T500C E-Line Blade TPD T043 .043" T116 .116 T188 .188” T430 .430"
T045 .045" T118 .118” T219 .219” T4375 .4375"
T059 .059" T125 .125” T250 .250” T475 .475"
T060 .060" T1335 .1335" T266 .266” T500 .500”
T068 .068" T150 .150" T295 .295" T531 .531”
T071 .071" T155 .155" T300 .300" T625 .625
T086 .086” T156 .156" T325 .325" T750 .750"
T087 .087” T157 .157" T344 .344”
T500C-USS
P500 T092 .092" T160 .160" T350 .350"
T098 .098" T165 .165” T360 .360"

General Purpose Points and Accessories

Point Extensions Model Description
(Left to Right- T500C 50° Cone Contact Point, “V” Threads for TH-3001V, TH-3002V,TH-3004 Gages
PE-.300, PE-.500 T500C-USS Modified 50° Cone Contact Point, USS Improved Buttress
PE-.750, PE-1.00)
T501 50° Cone Contact Point, Self-Centering for TH-3001R, TH-3002R Gages
T502 Self-Centering Sleeve for T501 & T503 Contact Points
T503 50° Cone Contact Point, “V” Threads for TH-3006
E-Line .063” R Extreme Line Contact Point for TH-3003E Gage
TPD .020” R Contact Point for PD-3003 & PD-3004 Gages
PE-___ Point Extensions available in .300”, .500”, .750” & 1.00” (Ex. PE-300)
PA-45 45° Point Adapter, contact point not included
RC-375 .375” Diameter Roller Contact
P-500 TH-3001R Gage, Flat Face Contact
Blade-25 .008" thickness, .170" Diameter, .250" Depth Blade Point
Blade-50 .008" thickness, .170" Diameter, .500" Depth Blade Point

124 www.gagemaker.com • [email protected]

Contact Points(Continued)
UN Series (60° “V”) Threads
These contacts points are used to inspect the pitch diameter of machined parts with 60° “V” thread
forms. Two are required for most gages.

Model Thread Pitch Model Thread Pitch Model Thread Pitch Truncated Contact Point
T562 1 T115 5 T050 11½ & 12
T288 2 T105 5½ T041 14 & 16
T188 3 & 3½ T096 6 T032 18
T144 4 T072 8
Threaded Shank Contact Points
T128 4½ T057 10

Acme or Stub Acme Threads

T041
These truncated contact points are used to inspect the pitch diameter of machined parts with 29°
Acme and Stub Acme thread forms. Two are required for most gages.

Model Thread Pitch Model Thread Pitch Model Thread Pitch

T531T 1 T144T 3½ T050T 10
T344T 1½ T128T 4 T041T 12 & 14
T062
T266T 2 T105T 5 T032T 16
T219T 2½ T090T 6&7
T188T 3 T062T 8

7° x 45° Buttress Series Contact Points

T072
These contact points are used to inspect the pitch diameter of machined parts with 7° x 45° Buttress
thread forms. Two are required for most gages.

Model Thread Pitch Model Thread Pitch Model Thread Pitch

T562 1 T188 3 T072 8
T105
T437 1¼ T156 3½ T057 10
T375 1½ T144 4 T050 12
T281 2 T115 5 T032 16 & 18
T219 2½ T096 6

Trapezoidal Thread Contact Points

T115
These contact points are used to inspect the millimeter pitch diameter of machined parts with
Trapezoidal thread forms. Two are required for most gages.

Model mm Pitch Model mm Pitch

T144 7 T062 3
T125 6 T050 2½ T125
T096 5 T041 2
T082 4 T032 1½
T072 3½

ISO Metric Series Contact Points

These contact points are used to inspect the pitch diameter of machined parts with ISO Metric 60° T250
“V” thread forms. Two are required for most gages.

Model mm Pitch Model mm Pitch

T096 4 T057 2½
T072 3 & 3½ T041 1½, 1¾, & 2

Phone: 713-472-7360 • Fax: 713-472-7241 125

 Gagemaker Products

Thread Form
Straight Thread Form Profile Gages
Gagemaker manufactures precision straight thread profile gages for quick identification of a thread
form. Specify thread pitch to be inspected when ordering. Special form profiles are available.

Model Description Order Example

TP-UNVI-__P Internal UN series thread gage TP-UNVI-2P,
TP-UNVE-__P External UN series thread gage TP-UNVE-4P,
TP-GPA-__P Internal/external general purpose Acme thread profile gage TP-SA-8P, etc.
TP-SA-__P Internal/external Stub Acme thread profile gage
TP-SAM1-__P Modified 1 Stub Acme thread profile gage
TP-SAM2-__P Modified 2 Stub Acme thread profile gage
TP-MI-__P Internal ISO Metric series thread profile gage
TP-ME-__P External ISO Metric series thread profile gage
TP-745-__P Internal/External 7° X 45° Buttress thread profiile gage
Tapered Thread Form Profile Gages
Gagemaker manufactures precision tapered thread profile gages for the quick identification thread
form identification. When ordering, specify the connection to be inspected. Special profiles will be
quoted upon request.

Model Connection Type TPI, TPF, Thread Form

TP-RTC-8R API 8-Round Casing, Tubing & Drill Pipe 8 TPI, ¾” TPF, 8 Round
TP-RTC-10R API 10-Round Tubing 10 TPI, ¾” TPF, 10 Round
TP-8V 8V API Line Pipe 8 TPI, ¾” TPF, 8 V Thread
TP-11-1/2V 11½ V API Line Pipe 11½TPI, ¾” TPF, 11½ V Thread
TP-5BTC75-INT API Buttress Casing, Internal, 4½” - 13⅜” 5 TPI, ¾” TPF
Assorted Straight Thread Profiles
TP-5BTC75-EXT API Buttress Casing, External, 4½” - 13⅜” 5 TPI, ¾” TPF
TP-5BTC1-INT API Buttress Casing, Internal, 16” - 20” 5 TPI, 1” TPF
TP-5BTC1-EXT API Buttress Casing, External, 16” - 20” 5 TPI, 1” TPF
TP-3-1.25-84 2⅜” - 3½” Hughes Slimline H-90 3 TPI, 1.25” TPF, 90-V-0.084
TP-3.5-2-50 3½”- 6⅝” Hughes H-90 3.5 TPI, 2” TPF, 90-V-0.050
TP-3.5-3-50 7” - 8⅝” Hughes H-90 3.5 TPI, 3” TPF, 90-V-0.050
2⅜” - 3½” P.A.C. Connections
TP-4-1.5-76 4 TPI, 1.5” TPF, V-0.076
2⅜” - 4½” American Open Hole
6⅝” API Regular
TP-4-2-50 4 TPI, 2” TPF, V-0.050
5½” & 6⅝” API Full Hole
4” API Full Hole, 2⅞” - 5” Hughes Xtra Hole,
2⅜” - 4½” Hughes Slim Hole,
TP-4-2-38 4 TPI, 2” TPF, V-0.038R
2⅜” - 6⅝” Internal Flush
API Numbered Connections #23 - #50
TP-4-3-38 API Numbered Connections #56 - #77 4 TPI, 3” TPF, V-0.038R
TP-4-3-50 5½”, 7⅝”, & 8⅝” API Regular 4 TPI, 3” TPF, V-0.050
2⅜” - 4½” API Regular
TP-5-3-40 5 TPI, 3” TPF, V-0.040
2⅞”, 3½”, 4½” API Full Hole
API Numbered Connections #10, #12, #13, #16
Assorted Tapered Thread Profiles TP-6-1.5-55 6 TPI, 1.5” TPF, V-0.055
M.T. (Macaroni Tubing)
TP-6-2-32 2⅜" - 2⅞” Hughes External Flush 6 TPI, 2” TPF, V-0.032
TP-9060LS 90° & 60° Threads, Tool Grinding & Setting Gage Tool Grinding & Setting Gage
TP-NPT-8 NPT Threads 8 TPI, ¾” TPF
TP-NPT-11-1/2 NPT Threads 11.5 TPI, ¾” TPF
TP-NPT-14 NPT Threads 14 TPI, ¾” TPF
Specials Available Upon Request

126 www.gagemaker.com • [email protected]

Thread Form Profile Overlays
Overlay Charts for profiles are available. For more information, please contact customer service.

Special Overlay are also available. For Special Overlays, please specify the following:
1. Screen Size
2. Magnification 20X/50X
3. Product Form or Profile Template

Buttress Runout
Buttress Runout Gage BR-2001

Buttress runout gages ensure proper thread pullout on runout type threads. Thread runout is the
measurement of the abruptness with which the buttress thread is terminated at the triangle end of
the thread. A rapid pull-out of the cutting tool results in steep slope at the end of the thread. This
causes high stress at the contact point when the coupling is made-up. Buttress runout gages have
standard 1” and 2” point spacing. Inlcudes one contact point (TBR) and shoes.

Model Description Range

BR-2001 Buttress Runout Gage All Sizes
BR-2001-USS Buttress Runout Gage for USS Improved Buttress All Sizes
BRB-2001 Buttress Runout Base Only All Sizes
TI-RSC-60
BRS-2001 Replacement Shoes (2)

Insert Identification
Insert Identifiers
Gagemaker’s thread insert indentifiers easily determine which threading insert the machinist is using.
When an optical comparator is unavailable, the insert indentifier will show which thread form is on
the insert.

Model Taper Per Foot/Pitch Thread Forms

Rotary Shouldered Connections- V-0.032,
TI-RSC-60 1.5", 2", & 3" V-0.038R, V-0.040, V-0.050, V-0.055, V-0.065, &
V-0.076

Rotary Shouldered Connections- A-0.094,

TI-RSC-90 1.25", 2", 3", & 3.373"
90-V-0.050, & 90-V-0.084
3P, 3.5P, 4P, 5P, 6P, 8P, 10P, 12P,
TI-ACME-INT Internal Acme
14P, & 16P
3P, 3.5P, 4P, 5P, 6P, 8P, 10P, 12P,
TI-SACME-INT Internal Stub Acme
14P, & 16P

Tubing and Casing - 8 Round, 10 Round, & ¾” and

TI-T&C ¾” and 1”
1” Internal and External Buttress

Phone: 713-472-7360 • Fax: 713-472-7241 127

 Gagemaker Products

Software
Thread Disk Software
Straight Thread Dimensions TDWIN
The Thread Disk engineering software calculates critical dimensions for threads based on ANSI tables
and formulas. Thread types supported by the program include: UN, UNJ and UNR Series, Acme, Stub
Acme, Stub Acme Modified I and II, Metric M & MJ, 7º X 45º Buttress, and General Purpose Pipe
Threads.

To generate critical dimensions instantly, enter basic thread information on the Thread Type Entry
screen, such as: thread type, thread class, nominal diameter, and threads per inch. Once the results
are computed, tabs at the bottom of the program allow selection of several types of calculated
information, including dimensions and tolerances for product threads, ring gages, set plugs, plug
gages or Gagemaker’s Thread Diameter gages.
TDWIN Software
If measuring internal and external shallow taper diameters is a problem, the Ball Mic SET DIM Tool
provides setting dimensions for ball micrometers or Gagemaker’s BX-1000 groove gage. The program
calculates ball mic settings for any tapered surface geometry.

Other features of the program include the ability to print thread dimension reports, providing a
paper copy of any calculation. These reports provide the same critical dimensions that display in the
program. A multiple calculation window capability is a feature that allows performing several different
thread calculations at the same time.

System Requirements

• Windows XP or higher
• 64 MB RAM
• 3 MB of free hard disk space
• CD-ROM drive

Features

• Uses ANSI tables, formulas, and tolerances

• Calculates standard and non-standard product thread diameters from #000 to 99.8”
• Calculates ANSI ring and plug gage dimensions
TDWIN Screenshots • Addresses pitches from 1 to 400
• Calculates Gagemaker style thread gage setting dimensions

Model Description
TDWIN Thread Disk software
TDWIN-Network Multi-user license agreement

TDWIN Report

128 www.gagemaker.com • [email protected]

Thread Disk Software
Tapered Thread Dimensions TDWIN Taper
Gagemaker's TDWIN Taper software simplifies the API specifications that control connection
quality. TDWIN Taper produces dimensional drawings and inspection data for API downhole tubular
connections based on the most current industry standards. All the necessary details to machine,
inspect and document tubular connection threads are available in one convenient program.

TDWIN Taper provides easy access to information for both preferred and non-preferred Rotary
Shouldered Connections, Tubing and Casing Connections, and any combination of Crossover.
The program offers standard connection types and sizes. TDWIN Taper relies on API and industry
standard tables and tolerances. It displays connection drawings, inspection gage information, and
setup and inspection reports.

The software displays printable drawings suitable for manufacturing. The drawings follow ASME
Y14.5 standards for industry compatibility. Print gage setup and inspection reports with your
company logo and work order information. The program offers the choice to save reports and jobs
for future reference.
TDWIN Taper Software

Tapered oilfield connection types supported by the program include the following:

Rotary Shouldered Connections

API Numbered Connections PAC Slimline H-90
API Regular Slim Hole External Flush
Full Hole Wide Open Acme Regular
Internal Flush Xtra Hole Acme Streamline
Open Hole H-90 Double Streamline

Tubing and Casing Connections

NUE Tubing USS Improved Buttress Tubing
EUE Tubing Line Pipe
Short Thread Casing Special Clearance Couplings
Long Thread Casing SR13 Seal Ring Groove Couplings
Buttress Casing

TDWIN Taper Screenshots

System Requirements

• Microsoft Windows XP or newer

• USB 2.0 port
• Internet Connection for first use
• 1 MB RAM or more (recommended)
• Screen resolution of 1024 x 768 minimum
• .Net Framework 2.0 or later installed

Features

• Print dimensional reports and inspection sheets

• Print product blueprints for manufacturing and inspection
• Provides gages configurations, setting standards, and contact point information TDWIN Taper Report

Model Description
TDWIN-Taper Thread Disk Software for Tapered Threads
TDWIN-Taper-Network Multi-user license agreement

Phone: 713-472-7360 • Fax: 713-472-7241 129

 Gagemaker Products

Indicators
83-0582

Dial Indicators
83-0584 Gagemaker’s mechanical indicators are manufactured per ANSI AGD specifications.

Model Correlating Gage Model Travel Resolution

1512SGA (CONT) WT-9000 Series .250” .0005”

1512SRGA (CONT) TH-3002R, TH-3002V, PD-3003 .250” .0005”
1513SGA (BAL) PN-3000 Series, BX-1000, BXG-1000 (was 803) .125” .0005”
1513SRGA (BAL) TH-3002B, TH-3003B, TS-4000 (was 803I) .125” .0005”
2046SGA 801 (BAL) BR-2001 .250” .001”
801I (BAL) TH-3002R, TH-3002V .250” .001”
802 (CONT) WT-9000 Series .250” .001”
863 802I (CONT) TH-3001R, TH-3001V, PD-3003 .250” .001”
862L (CONT) ET-7001, ET-7002, ET-7004, ET-7006 Series w/ Lever .500” .001”
862I (CONT) IT-6001, PD-3004 .500” .001”
RG-7000 Series, TH-3004, TH-3006, TH-3008,
863 TH-3009, TH-3010, SRG-7000, CA-9001, MRP-5000 .500” .0005”
Series, SPG-6000
863L (BAL) PD-8000 Series w/ Lever .500” .0005”
PD-6000, PD-6001, PG-6000 Series,
543-683B 863I (BAL) .500” .0005”
TS-1000, IT-5100, MRP-5500, SPG-6000
882L (CONT) ET-7003, ET-7005, ET-7007 w/ Lever 1.00” .001”
882I
882I (CONT) IT-6000 1.00” .001”
80-0403 LG-5002, LG-5003 .100" .0005”
80-0400 LG-5002, LG-5003 .025” .0001”
83-0584 MRP-2000, MRP-2500, MRP-3000 .500” .001”
83-0582 MRP-2000, MRP-2500, MRP-3000 .500” .0005”
87-070 MRP-1000, MRP-1500 .125” .0005”
Notes: (BAL) indicates Balanced.
(CONT) indicates Continuous.
“I” after the model number indicates counter clockwise rotation.
“L” after model number indicates a lifting lever .

Multipurpose Indicators
803

Model Description Travel Resolution

2358B-MRP All MRP Gages .500” .0001”
2358SGA Multipurpose Indicator, Balanced .500" .0001"
2358SRGA Multipurpose Indicator, Balanced .500" .0001"
2776SGA Multipurpose Indicator, Continuous, Clockwise 1.00” .0005”
2776SRGA Multipurpose Indicator, Continuous, Counterclockwise 1.00” .0005”
2777SGA Multipurpose Indicator, Balanced, Clockwise 1.00” .0005”
2777SRGA Multipurpose Indicator, Balanced, Counterclockwise 1.00” .0005”
1513SGA

M801

1044SRGA

130 www.gagemaker.com • [email protected]

Metric Dial Indicators

Model Description Travel Resolution

Bezel
1044SGA Metric Mechanical, Continuous, Clockwise 5 mm .01 mm Assembly
1044SRGA Metric MechanicaL, Continuous, Counterclockwise 5 mm .01 mm
1045SGA Metric Mechanical, Balanced, Clockwise 5 mm .01 mm
1045SRGA Metric Mechanical, Balanced, Clockwise 5 mm .01 mm
2046SGA Metric Mechanical, Continuous, Clockwise 10 mm .01 mm
2047SGA Metric Mechanical, Balanced, Clockwise 10 mm .01 mm
21AZB151
2902SRGA Metric Mechanical, Continuous, Counterclockwise 10 mm .01 mm
2047SRGA Metric Mechanical, Balanced, Clockwise 10 mm .01 mm
2050S-01 Metric Mechanical, Continuous 20 mm .01 mm

Digital Indicators

Model Description Travel Resolution Accuracy

543-452B Electronic/Digital 1” .00005” .0005” 21RZA065
543-683B Electronic/Digital .500” .0005” .0005”
SC0232014-00 Electronic/Digital (RSC Only) .500” .0005”/.0001” .0005”/.0001”

Indicator Replacement Parts

193592 &
Dial rings are available for all indicators. Please call for more information. 193690

Small Dials

Model Description
21AZB353 Bezel Assembly (Blue "S" Type)
21BAA147A Bezel Assembly (Black "F" Type)
21AAB364 Bezel Clamp Washer (Blue "S" Type)
21AAB162 Bezel Clamp Screw (Blue "S" Type)
193592 Bezel Clamp Washer (Black "F" Type)
193690 Bezel Clamp Screw (Black "F" Type)
900527 Mitutoyo Lifting Lever

Large Dials

Model Description
21AZB161 Bezel Assembly (Blue "S" Type)
192683 Bezel Assembly (Black "F" Type)
21RZA065 Bezel Clamp Assembly (Blue "S" Type)
21BA083 Bezel Clamp Washer (Black "F" Type) SC0232014-00

101214 Bezel Clamp Screw (Black "F" Type)

21AZB151 Mitutoyo Lifting Lever

Phone: 713-472-7360 • Fax: 713-472-7241 131

 Gagemaker Products

Gage Setting and Part Measurement

Gage Setting and Part Measurement Systems
This package features the MIC TRAC as a multi-use gage setting system. The system sets or zeros
most gages with the use of interchangeable anvils or blocks. Standard resolution of base unit is
.00005”. Accuracies range from ±.0001” to ±.0004”. The Digital Read Out (DRO) is CE approved.
All MIC TRAC 3000 Series inlcude one set of TF-PL blocks and a shipping carton. Larger ranges are
available, please contact customer service for more information.

Shop Floor Gage Setting and Part Measurement System

Model Description Accuracy Resolution Range

MT-3000 Standard Base Units without Force-Lok
Int. 0” - 12”
MT-3012-50 MIC TRAC Base Unit w/ DRO +.0001” .00005”
Ext. 1½" - 13½"
Int. 0” - 24”
MT-3024-50 MIC TRAC Base Unit w/ DRO +.0002” .00005”
Ext. 1½" - 25½"
Int. 0” - 36”
MT-3036-50 MIC TRAC Base Unit w/ DRO +.0003” .00005”
Ext. 1½" - 37½"
Int. 0” - 48”
MT-3012-50 MT-3048-50 MIC TRAC Base Unit w/ DRO +.0004” .00005”
with TF-PL Blocks Ext. 1½" - 49½"
MT-3000 Standard Base Units with Force-Lok
MIC TRAC Base Unit w/ DRO Int. 0” - 12”
MT-3012F-50 +.0001” .00005”
and Force-Lok Ext. 1½" - 13½"
MIC TRAC Base Unit w/ DRO Int. 0” - 24”
MT-3024F-50 +.0002” .00005”
and Force-Lok Ext. 1½" - 25½"
DRO
MIC TRAC Base Unit w/ DRO Int. 0” - 36”
MT-3036F-50 +.0003” .00005”
and Force-Lok Ext. 1½" - 37½"
MIC TRAC Base Unit w/ DRO Int. 0” - 48”
MT-3048F-50 +.0004” .00005”
and Force-Lok Ext. 1½" - 49½"
MT-3000 Base Unit with Computer & MT-4-USB
MT-4-USB MIC TRAC Base Unit with Force-Lok, Int. 0” - 12”
MT-3012F-50-USBC +.0001” .00005”
Computer, & USB Ext. 1½" - 13½"
MIC TRAC Base Unit with Force-Lok, Int. 0” - 24”
MT-3024F-50-USBC +.0002” .00005”
Computer, & USB Ext. 1½" - 25½"
MIC TRAC Base Unit with Force-Lok, Int. 0” - 36”
MT-3036F-50-USBC +.0003” .00005”
Computer, & USB Ext. 1½" - 37½"
MIC TRAC Base Unit with Force-Lok, Int. 0” - 48”
MT-3048F-50-USBC +.0004” .00005”
Computer, & USB Ext. 1½" - 49½"
High Resolution MT-3000 Base Unit with Computer & MT-4-USB
Computer
MIC TRAC Base Unit with Force-Lok, Int. 0” - 12”
MT-3012F-10-USBC +.00005” .00001”
Computer, & USB Ext. 1½" - 13½"
MIC TRAC Base Unit with Force-Lok, Int. 0” - 24”
MT-3024F-10-USBC +.00010” .00001”
Computer, & USB Ext. 1½" - 25½"
MIC TRAC Base Unit with Force-Lok, Int. 0” - 36”
MT-3036F-10-USBC +.00015” .00001”
Computer, & USB Ext. 1½" - 37½"
MIC TRAC Base Unit with Force-Lok, Int. 0” - 48”
MT-3048F-10-USBC +.00020” .00001”
Computer, & USB Ext. 1½" - 49½"
MIC TRAC Base Unit with Force-Lok, Int. 0” - 60”
MT-3060F-10-USBC +.00023” .00001”
Computer, & USB Ext. 1½" - 61½"

132 www.gagemaker.com • [email protected]

MIC TRAC Setting Blocks
TF-1F
The MIC TRAC 3000 receiver blocks include precision, calibrated surfaces designed for mounting all the
various setting blocks. Depending on the requirements of the application, each pair of MIC TRAC setting
blocks is precisely ground with either a flat or tapered gauging surface.  Setting blocks are supplied in
sets of two, with various degrees of taper available.
TF-PL
Model Description
Shallow Tapered Cylinder Setting Blocks (2 Block Sets) (used with BX-1000 gages)
TF-10 Tapered Setting Blocks 10° half angle
TF-1V
TF-15 Tapered Setting Blocks 15° half angle
TF-20 Tapered Setting Blocks 20° half angle
TF-30 Tapered Setting Blocks 30° half angle
TF-45 Tapered Setting Blocks 45° half angle
Special Purpose Setting Blocks
TF-.5F Flat Face Setting Blocks (1.000” outside diameter)
TF-1F Universal flat face setting / measuring blocks (1.500” outside diameter)
TF-PL Flat Face Setting Blocks, No taper (supplied with MIC TRAC)
TAPER
API 6A Ring Groove & Special Flange Groove Setting Blocks BLOCKS
23° BXR Ring Groove Diameter/Width Setting Blocks, used with BX-1000 gages
TF-BX
(2 per set)
Thread Gage Setting Blocks
TF-1V 3-5 pitch 60° “V” thread setting blocks (2 per set)
TF-2V 6-20 pitch 60° “V” thread setting blocks (2 per set)
Tubing and Casing Taper Setting Blocks
TF-BX
TF-STR Straight Blocks
TF-.75T ¾” Taper Blocks, 8 & 10 Round, ¾” TPF Buttress, Line Pipe
TF-1.0T 1” Taper Blocks, 1” TPF Buttress TF-30

TF-1.12T 1⅛” Taper Blocks, 1.125 TPF Connection

TF-1.75T 1¾” Taper Blocks, 1.75 TPF Connections
Special Taper Blocks Available

MRP Straight Face Setting Blocks

TF-1F-T Flat face setting blocks to accept riser block (T-Shape)
Riser Blocks for the Taper Blocks
TF-1F-T
TF-RISER1 1.00” Riser Block (Set of 2)
TF-RISER2 2.00” Riser Block (Set of 2)
Special Taper
TF-RISER3 3.00” Riser Block (Set of 2) Blocks Available

TF-RISER1 TF-RISER3

TF-RISER2

Phone: 713-472-7360 • Fax: 713-472-7241 133

 Gagemaker Products

MT-4000 with
Computer
Precision Gage Calibration System
MIC TRAC 4000 Package
This package features the MIC TRAC/MT-4000 as a precision calibration system. The system accepts
fixtures that inspect and calibrate a wide range of gage diameters and thread pitches. The package
includes all the equipment necessary to calibrate precision handheld gages. Ring and plug inspection
requires the purchase of additional accessories.

Package includes:
• MT-4012-10 MIC TRAC electronic adjustable measurement master, range 0” to 12”. Base unit
is error compensated to an accuracy of ±.00005”, resolution .00001”, travel 12.000”.
CERTIFI • Ultra precision scale with 1.00” travel, accuracy ±.00002”, and resolution .00001”.
MT-4-USB
• Computer with CERTIFI Calibration Software. CERTIFI produces calibration reports, has a
recall database, and a digital readout acquisition module.
• CRC MT-4000 Calibration Reference Card Set: procedures documenting calibrations with the
Gagemaker system
• TF-2R: Carbide anvil set, ⅜” diameter
• TF-XYT: Adjustable X, Y & tilt support table for use with the MIC TRAC
TF-2R • CAL-PAK: Assortment of fixtures designed to hold gages for calibration
TDWIN • TDWIN Thread Disk software program: provides critical thread dimensions for manufacturing
and inspection of UN, Acme, Stub Acme, Metric, Buttress, and NPT threads.
• Torque wrench, 50 in. lb. (TW-50)
• AWH-100 bench-top tool holder with wrenches
• Reusable shipping container
CRC MT-4000
Model Description Range
AWH-100
PGC-12-W2 Precision Calibration Package 0” - 12”

Additional Packages & Calibration Accessories

TW-50
The following base units and accessories for larger requirements are available options to the
standard MIC TRAC Package above.

Model Description Range

PGC-24-W2 Precision Calibration Package with MT-4024-10 MIC TRAC 0” - 24”
TF-XYT
PGC-36-W2 Precision Calibration Package with MT-4036-10 MIC TRAC 0” - 36”
PGC-48-W2 Precision Calibration Package with MT-4048-10 MIC TRAC 0” - 48”

MIC TRAC Package Training Options

We also offer expert-led training for our precision gage calibration systems at your location or at
our facility. Please contact customer service for more information.
CAL-PAK
PGC-__-W2 Training Options: Option A: Training at customer’s facility (per day, plus airfare)
Option B: Training at Gagemaker’s facility (per day, per person)

MT-4000 Base Units with Extended Software Functions

A MIC TRAC 4000 base unit supplied only with digital readout software with extended functions, a
computer, TF-2R setting blocks, and shipping carton.

Model Description Accuracy Resolution Range

MT-4012-10 MIC TRAC Base Unit +.00005” .00001” 0” - 12”
MT-4024-10 MIC TRAC Base Unit +.00005” .00001” 0” - 24”
MT-4036-10 MIC TRAC Base Unit +.00005” .00001” 0” - 36”
MT-4048-10 MIC TRAC Base Unit +.00005” .00001” 0” - 48”

134 www.gagemaker.com • [email protected]

Precision Gage Calibration System (MT-4000) Accessories
Gagemaker provides various accessories to expand the functionality of the MIC TRAC 4000 base unit. TF-SB
Some of the following are included as a package, but they are also available individually.

Model Description
AWH-100 Hex wrench holder with wrenches
Complete procedural documentation for the calibration of handheld inspection equipment
CRC-MT4000 including: O.D. & I.D. micrometers, calipers, depth micrometers, ring and plug gages, and
more.
MT-4-USB Digital readout software module with digital data acquisition card w/ CERTIFI TF-SB-1

Thread Disk software for calculating critical setting dimensions for threads. Includes UN
TDWIN
Series, Acme, Stub Acme, ISO Metric, and 7° X 45° Buttress thread forms.
TF-2R ⅜” diameter carbide anvil set TF-CR

TF-SB Adjustable height support table

TF-SB-1 Bearing rail support base
TF-XYT Adjustable height support table, X-axis & Y-axis support base
TW-50 50 in-lb torque wrench with 5/32” hex wrench adapter
Cylindrical Ring & Thread Ring and Plug Gage Accessories
TF-1F Flat face setting blocks
TF-1F-C Carbide flat face setting blocks
TF-CP Ball contact holders, .500 ID measurement
Set of 3 fixtures for measuring cylindrical ring gages and bores. CR-1 (.170”-.249”), CR-2 TF-IT
TF-CR
(.250”-.879”), CR-3 (.880”- Larger)
Internal threaded ring arm P.D. module (for solid threaded ring gages). Contains ball
TF-IT contacts and holders for 6, 8, 10, 12, 14, 16, 18, and 20 pitch 60° threads (Diameter range
1.500” & Larger).
TF-SP-S
TF-SP-5 For vertically holding gage pins .062” - .500”
TF-SP-75 For vertically holding gage pins .062” - .750”
Calibration fixture for NPT, NPTF and ANPT tapered plug gages (includes wire for 27, 18,
TF-TP
14, and 11½ pitch threaded plugs). (Requires TF-2R blocks)
Thread Wire Holder Modules for UN, Acme, and Metric Threads
TF-WS
All wire holders require TF-2R Blocks and are supplied with one set of wires. Please specify pitch required.
Note: “__” denotes pitch, ex. TF-WHV-12 = 60° thread wire holder module with wires 12 pitch.
60° thread wire holder module with your choice of wires. Please select one pitch from the
TF-WHV-__
following range: 5 pitch to 48 pitch
TF-TP
60° thread wire holder module with your choice of wires. Please select one pitch from the
TF-WHVP-__
following range: 1 pitch to 4 pitch or 56 pitch to 72 pitch
29° thread wire holder module with your choice of wires. Please select one pitch from the
TF-WHA-__
following range: 4 pitch to 20 pitch
TF-WHAP-__ 29° thread wire holder module with your choice of 2 pitch or 3 pitch wires TF-CP
Metric thread wire holder module with your choice of wires. Please select one pitch from
TF-WHM-__
the following range: 0.5 mm pitch to 0.8 mm pitch or 5 mm pitch to 6 mm pitch
Metric thread wire holder module with your choice of wires. Please select one pitch from
TF-WHM-__
the following range: 1.0 mm pitch to 4.5 mm pitch
Thread wire holder Set. Contains wires and holders for 6, 8, 10, 12, 14, 16, 18, 20, 24, 28
TF-WSV
and 32 pitch 60° threads.
Thread wire holder Set. Contains wires and holders for 4, 5, 6, 8, 10, 12, 14 and 16 pitch
TF-WSA
Acme 29° threads.
Thread wire holder set. Contains wires and holders for .5, .6, .75, 1.0, 1.25, 1.5, 2.0, 3.0,
TF-WSM
4.0 and 5.0 pitch metric 60° threads.
TF-WH-__ Wire holder only (Indicate V, A, or M and then wire size or pitch)

Phone: 713-472-7360 • Fax: 713-472-7241 135

 Gagemaker Products

TF-1F
TF-SS MIC TRAC System Options
The following accessories are available for larger requirements for either the MIC TRAC 3000 or
MIC TRAC 4000.

TF-SA Model Description

Complete Calibration Package
CAL-PAK Includes: TF-1F, TF-CA, TF-DG, TF-IND, TF-LG-2, TF-LG-3, TF-SA, TF-SS, TF-SV, TF-VB,
and storage case (included with a MT-4000 Package (PGC-12-W2, etc.))
TF-IND AGD dial indicator. Calibration fixture (includes .375” and 8mm bushing)
TF-CA TF-DG Calibration fixture for depth micrometer*
TF-CA Caliper calibration accessory dial, digital and vernier calipers. Includes TF-SA support arm.
TF-TI Test indicator calibration block*
TF-IND
TF-VB TF-SA Support arm for TF-CA.
TF-SS Straight support accessory for support of extended probes*
TF-SV “V” support accessory for calibrating micrometers and standards**
TF-VN “V” blocks for calibration of axial travel probes and bore gages
TF-1F Flat face setting block set (2 blocks) 1.5000” outside diameter
TF-SV TF-BA Base support block for setting dial bore gages**
TF-VB “V” block fixture for calibration of Gagemaker’s TH-3004 and MRP-2002 Upper arms*
TF-DG TF-LG-2 Lead gage calibration fixture for either Allen or Gagemaker gages (LG-5002)
TF-LG-3 Gagemaker lead gage (LG-5003) calibration fixture*
TF-BI Base support plate for setting dial bore gages**
TF-LG-2 TF-CG Universal clamping fixture for calibration of indicators and gages*
TF-LG-3 Complete procedural documentation for the calibration of handheld inspection equipment
CRC-MT3000
including: O.D. & I.D. micrometers, calipers, depth micrometers, and more. (MT-3000 ONLY)
TF-VN Complete procedural documentation for the calibration of handheld inspection equipment
CRC-MT4000 including: O.D. & I.D. micrometers, calipers, depth micrometers, ring and plug gages, and
more. (MT-4000 ONLY)
TF-BA *1 TF-1F block required with this accessory
**2 TF-1F blocks required with this accessory
TF-BI
Bench Calibrator
TF-CG
The Gagemaker bench calibrator, CG-1001/CG-1001E, calibrates gages and indicators per AGD
specification. The CG-1001 uses a non-rotating spindle screw type micrometer which reads directly
to .0001” and can be estimated to the closest .00005".

Disassembling the gage is not required for calibration. The vise assembly allows full vertical and
CRC-3000
horizontal adjustment of the gage or indicator clamped in the vise jaws. During calibration, an
outboard arm and arm support allows for larger gage assemblies to be securely supported. Four
CG-1001
supplied accessory fixtures will help speed up calibration while maintaining accuracy.*

The CG-1001 is our standard bench calibrator, while the CG-1001E is our digital version which
includes an SPC output.

Bench Calibrators are shipped in a durable custom shipping/storage case. Optional wooden storage
cases are available.

Model Description Range Accuracy

CG-1001 Bench Calibrator .0001” Resolution, Mechanical ±.0001

Digital Bench Calibrator Gage w/

CG-1001E .00005”/.001 mm Resolution, Digital ±.00015
SPC Output
CG-1001E *Individual replacement fixtures are available for purchase but not listed above.
Please call for more information.

136 www.gagemaker.com • [email protected]

API 6A Seal Ring Groove Gages (BX/RX)
BX-900

Face Groove and Hole Location Gages

Gagemaker’s face groove gages inspect groove diameters and groove widths. Excellent for inspecting
hoel locations. Additional extensions for various lengths are available, please contact customer
service for more.

Model Description Range BX-1000

BX-900 Ball Mic Gage w/ Ball Points (no indicator) BX, R, RX Grooves, Diameters 2.6” - 13”
BX-1000 6B Groove Diameter Gage w/ T188 Points BX, R, RX Grooves, Diameters 2.6” - 13”
BXG-1000 6B Groove Width Gage w/ T072 Points BX, R, RX Grooves, Widths .375” - 1.5”
BXG-1002 Special Groove Width Gage w/ T072 Points Special Groove, Widths 2.0”
BX-R13 Optional Extension rod for BX-1000, 13” Groove Diameters to 13”
BX-R24 Optional Extension rod for BX-1000, 24” Groove Diameters to 25”
BX-R30 Optional Extension rod for BX-1000, 30” Groove Diameters to 31”
BX-R36 Optional Extension rod for BX-1000, 36” Groove Diameters to 37”
PD-BX BX/BXG Setting Gage, ½” X ½” U-notch

Face Groove and Hole Location Gage Setting Masters

Model Description Model Description BXG-1000

FSBX-150 Setting Master for BX-150 FSBX-162 Setting Master for BX-162
FSBX-151 Setting Master for BX-151 FSBX-163 Setting Master for BX-163
FSBX-152 Setting Master for BX-152 FSBX-164 Setting Master for BX-164
FSBX-153 Setting Master for BX-153 FSBX-165 Setting Master for BX-165
FSBX-154 Setting Master for BX-154 FSBX-166 Setting Master for BX-166
FSBX-155 Setting Master for BX-155 FSBX-167 Setting Master for BX-167
FSBX-156 Setting Master for BX-156 FSBX-168 Setting Master for BX-168
FSBX-157 Setting Master for BX-157 FSBX-169 Setting Master for BX-169
FSBX-158 Setting Master for BX-158 FSBX-170 Setting Master for BX-170
FSBX-159 Setting Master for BX-159 FSBX-171 Setting Master for BX-171
FSBX-160 Setting Master for BX-160 FSBX-172 Setting Master for BX-172
FSBX-161 Setting Master for BX-161 FSBX-303 Setting Master for BX-303

BX - Dog Bone/Paddle Gage

Model Description Model Description

DBBX-150 Dog Bone Ring Groove Gage BX-150 DBBX-162 Dog Bone Ring Groove Gage BX-162 Face Groove and Hole Location Standards
(FSBX)
DBBX-151 Dog Bone Ring Groove Gage BX-151 DBBX-163 Dog Bone Ring Groove Gage BX-163
DBBX-152 Dog Bone Ring Groove Gage BX-152 DBBX-164 Dog Bone Ring Groove Gage BX-164
DBBX-153 Dog Bone Ring Groove Gage BX-153 DBBX-165 Dog Bone Ring Groove Gage BX-165 PD-BX
DBBX-154 Dog Bone Ring Groove Gage BX-154 DBBX-166 Dog Bone Ring Groove Gage BX-166
DBBX-155 Dog Bone Ring Groove Gage BX-155 DBBX-167 Dog Bone Ring Groove Gage BX-167
DBBX-156 Dog Bone Ring Groove Gage BX-156 DBBX-168 Dog Bone Ring Groove Gage BX-168
DBBX-157 Dog Bone Ring Groove Gage BX-157 DBBX-169 Dog Bone Ring Groove Gage BX-169
DBBX-158 Dog Bone Ring Groove Gage BX-158 DBBX-170 Dog Bone Ring Groove Gage BX-170
DBBX-159 Dog Bone Ring Groove Gage BX-159 DBBX-171 Dog Bone Ring Groove Gage BX-171 PD-BX Setting a BX-1000
DBBX-160 Dog Bone Ring Groove Gage BX-160 DBBX-172 Dog Bone Ring Groove Gage BX-172
DBBX-161 Dog Bone Ring Groove Gage BX-161 DBBX-303 Dog Bone Ring Groove Gage BX-303

Phone: 713-472-7360 • Fax: 713-472-7241 137

 Gagemaker Products

BX - Groove Profile & Width GO/NO GO Gage

Model Description Model Description
BXP-150 GO/NO GO Profile Gage BX-150 BXP-162 GO/NO GO Profile Gage BX-162
BXP-151 GO/NO GO Profile Gage BX-151 BXP-163 GO/NO GO Profile Gage BX-163
BXP-152 GO/NO GO Profile Gage BX-152 BXP-164 GO/NO GO Profile Gage BX-164
BXP-153 GO/NO GO Profile Gage BX-153 BXP-165 GO/NO GO Profile Gage BX-165
BXP-154 GO/NO GO Profile Gage BX-154 BXP-166 GO/NO GO Profile Gage BX-166
BXP-155 GO/NO GO Profile Gage BX-155 BXP-167 GO/NO GO Profile Gage BX-167
DB-R36
BXP-156 GO/NO GO Profile Gage BX-156 BXP-168 GO/NO GO Profile Gage BX-168
BXP-157 GO/NO GO Profile Gage BX-157 BXP-169 GO/NO GO Profile Gage BX-169
BXP-158 GO/NO GO Profile Gage BX-158 BXP-170 GO/NO GO Profile Gage BX-170
BXP-159 GO/NO GO Profile Gage BX-159 BXP-171 GO/NO GO Profile Gage BX-171
BXP-160 GO/NO GO Profile Gage BX-160 BXP-172 GO/NO GO Profile Gage BX-172
BXP-161 GO/NO GO Profile Gage BX-161 BXP-303 GO/NO GO Profile Gage BX-303

R & RX - Dog Bone/Paddle Gage

BX- Groove Profile &
Width Go/NoGo Gage
Model Description Model Description
DB-R20 Dog Bone Ring Groove Gage R-RX20 DB-R57 Dog Bone Ring Groove Gage R-RX57
DB-R23 Dog Bone Ring Groove Gage R-RX23 DB-R63 Dog Bone Ring Groove Gage R-RX63
DB-R24 Dog Bone Ring Groove Gage R-RX24 DB-R65 Dog Bone Ring Groove Gage R-RX65
DB-R25 Dog Bone Ring Groove Gage R-RX25 DB-R66 Dog Bone Ring Groove Gage R-RX66
DB-R26 Dog Bone Ring Groove Gage R-RX26 DB-R69 Dog Bone Ring Groove Gage R-RX69
BX- Dog Bone Paddle Gage
DB-R27 Dog Bone Ring Groove Gage R-RX27 DB-R70 Dog Bone Ring Groove Gage R-RX70
DB-R31 Dog Bone Ring Groove Gage R-RX31 DB-R73 Dog Bone Ring Groove Gage R-RX73
DB-R35 Dog Bone Ring Groove Gage R-RX35 DB-R74 Dog Bone Ring Groove Gage R-RX74
DB-R37 Dog Bone Ring Groove Gage R-RX37 DB-R82 Dog Bone Ring Groove Gage R-RX82
DB-R39 Dog Bone Ring Groove Gage R-RX39 DB-R84 Dog Bone Ring Groove Gage R-RX84
DB-R41 Dog Bone Ring Groove Gage R-RX41 DB-R85 Dog Bone Ring Groove Gage R-RX85
R & RX DB-R44 Dog Bone Ring Groove Gage R-RX44 DB-R86 Dog Bone Ring Groove Gage R-RX86
Dog Bone Paddle Gage DB-R45 Dog Bone Ring Groove Gage R-RX45 DB-R87 Dog Bone Ring Groove Gage R-RX87
(DB-R23)
DB-R46 Dog Bone Ring Groove Gage R-RX46 DB-R88 Dog Bone Ring Groove Gage R-RX88
DB-R47 Dog Bone Ring Groove Gage R-RX47 DB-R89 Dog Bone Ring Groove Gage R-RX89
DB-R49 Dog Bone Ring Groove Gage R-RX49 DB-R90 Dog Bone Ring Groove Gage R-RX90
DB-R50 Dog Bone Ring Groove Gage R-RX50 DB-R91 Dog Bone Ring Groove Gage R-RX91
DB-R53 Dog Bone Ring Groove Gage R-RX53 DB-R99 Dog Bone Ring Groove Gage R-RX99
DB-R54 Dog Bone Ring Groove Gage R-RX54

R-RX - Groove Profile & Width GO/NO GO Gage

Model
Corresponding R Groove Size
(RP-Depth-Width)*
RP-250-344 R 20
RP-310-469 R 23 to R45, R49, R53, R57, R65, R69, R82, R84, & R99
RP-380-531 R46, R73, R85
RP-440-656 R50, R54, R66, R86, R87
RP-500-781 R47, R70, R74, R88
RP-560-906 R90
RP-620-1063 R63
RP-690-1313 R91
*ex. RP-250-344 = .250”(depth), .344” (width)

138 www.gagemaker.com • [email protected]

Groove Width Amplifier Gages
Groove width amplifier gages use flushpins to indicate acceptance or rejection.

Model Description Groove Width

AG-BX150 Groove Width Amplifier Gage, BX-150 0.450”

AG-BX151 Groove Width Amplifier Gage, BX-151 0.466”

AG-BX152 Groove Width Amplifier Gage, BX-152 0.498”

AG-BX153 Groove Width Amplifier Gage, BX-153 0.554”

AG-BX154 Groove Width Amplifier Gage, BX-154 0.606”

AG-BX155 Groove Width Amplifier Gage, BX-155 0.698” AG-BX156

AG-BX156 Groove Width Amplifier Gage, BX-156 0.921”

AG-BX157 Groove Width Amplifier Gage, BX-157 1.039”

AG-BX158 Groove Width Amplifier Gage, BX-158 1.149”

AG-BX159 Groove Width Amplifier Gage, BX-159 1.279”

AG-BX160 Groove Width Amplifier Gage, BX-160 0.786”

AG-BX161 Groove Width Amplifier Gage, BX-161 0.930”

AG-BX162 Groove Width Amplifier Gage, BX-162 0.705”

AG-BX163 Groove Width Amplifier Gage, BX-163 1.006”

AG-BX164 Groove Width Amplifier Gage, BX-164 1.290”

AG-BX165 Groove Width Amplifier Gage, BX-165 1.071”

AG-BX151
AG-BX166 Groove Width Amplifier Gage, BX-166 1.373”

AG-BX167 Groove Width Amplifier Gage, BX-167 0.902”

AG-BX168 Groove Width Amplifier Gage, BX-168 1.018”

AG-BX169 Groove Width Amplifier Gage, BX-169 0.666”

CamLock Micrometers
The CamLock micrometers measure API weld flange thickness. Supplied with verification standard.
Replacement standards are available separately, please call for quotation.

Model Description Range

CL-1001 CamLock Micrometer- 25° 0” - 1”

CL-1002 with Verification Standard
CL-1002 CamLock Micrometer- 25° 1” - 2”

CL-1003 CamLock Micrometer- 25° 2” - 3”

CL-1004 CamLock Micrometer- 25° 3” - 4”

Phone: 713-472-7360 • Fax: 713-472-7241 139

 Gagemaker Products

SBG-5000E
Stator Minor Bore Inspection
SBG-5000A
Stator Bore Gages
The SBG series of gages determines a precise stator/rotor match by measuring the largest and
smallest bore diameters. SBG-5000 gages measure diameters from 1.500” - 7.500” and are available
in three models: an analog indicator (SBG-5000A), a digital indicator (SBG-5000D), and an electronic
(SBG-5000E). Attaching or removing different height extension shoes achieves the gage’s range
flexibility. All gage models can address any pitch or lobe configuration.

The SBG-5000A and SBG-5000D include three extension shoes and setting standard base without a
setting standard.

The SBG-5000E includes three extension shoes, interface box, a computer, measurement software,
necessary cables, and setting standard base without a setting standard.

Custom sized standards, round standards, and shoes are available. Setting standards are sold
separately. See the chart on page 141 for setting standard sizes.

Model Description Range

Stator Bore Gage with analog indicator & SB-2100,
SBG-5000A 1.500” - 2.000”*
SB-2110, and SB-2120 extension shoes

Interface Stator Bore Gage with digital indicator & SB-2100,

SBG-5000D 1.500” - 2.000”*
Box & SB-2110, and SB-2120 extension shoes
Computer
Electronic Stator Bore Gage with interface box,
SBG-5000E computer, software, standard base, & SB-2100, 1.500” - 2.000”*
SB-2110, and SB-2120 extension shoes

*Additional shoes are required for diameters exceeding 2.000”.

SBG-5000A, SBG-5000D & SBG-5000E Extension Shoes

The style of extension shoe depends on the diameter range being measured. Shoes are offered in
SBG Connection several lengths depending on the pitch of the stator lobes. It is important that the shoe length be long
Cable
enough to contact a minimum of two points on the bottom and one point on the top pad. Custom
shoes are available as special request. Contact Gagemaker for more infomation.

Model Description Range

SBG Extension
Shoes SB-2100 8” long extension shoe 1.500” – 1.650”
SB-2110 8” long extension shoe 1.650” – 1.800”
SB-2120 8” long extension shoe 1.800” – 1.950”
SB-2200 20” extension shoe (requires riser)
SB-2150 .130” riser – SB-2200 extension shoe required 2.000” – 2.150”
SB-2300 .280” riser – SB-2200 extension shoe required 2.150” – 2.300”
SB-2400 .380” riser – SB-2200 extension shoe required 2.250” – 2.400”
SB-2500 .480” riser – SB-2200 extension shoe required 2.350” – 2.550”
SB-2600 .580” riser – SB-2200 extension shoe required 2.450” – 2.600”
SB-3500 20” extension shoe w/ brackets and adapter 2.600” – 3.500”
SB-4500 20” extension shoe w/ brackets and adapter 3.450” – 4.500”
SB-5500 20” extension shoe w/ brackets and adapter 4.450” – 5.500”
SB-6500 20” extension shoe w/ brackets and adapter 5.450” – 6.500”
SB-7500 20” extension shoe w/ brackets and adapter 6.450” – 7.500”

140 www.gagemaker.com • [email protected]

SBG-5000A, SBG-5000D, & SBG-5000E Flat Standards
Setting standards do not need to be sized to the exact bore of the stator’s bore. As long as the size of
the standard is within the measurement range of the gage, it can be used to preset the gage.
Custom sizes and round standards are available as special requests.

Setting Master Flat Standard Setting Master Flat Standard

Height Model Height Model
1.600” SBFS-1600 4.640” SBFS-4640
SBG Flat Standards
1.727” SBFS-1727 4.750” SBFS-4750
1.800” SBFS-1800 4.900” SBFS-4900
2.062” SBFS-2062 5.060” SBFS-5060
2.187” SBFS-2187 5.150” SBFS-5150
2.375” SBFS-2375 5.240” SBFS-5240
2.598” SBFS-2598 5.350” SBFS-5350
2.700” SBFS-2700 5.420” SBFS-5420
2.736” SBFS-2736 5.500” SBFS-5500
2.900” SBFS-2900 5.600” SBFS-5600
3.080” SBFS-3080 5.750” SBFS-5750
SBG Extension Shoes
3.150” SBFS-3150 5.850” SBFS-5850
3.245” SBFS-3245 5.960” SBFS-5960
3.303” SBFS-3303 6.050” SBFS-6050
3.400” SBFS-3400 6.140” SBFS-6140
3.425” SBFS-3425 6.250” SBFS-6250
3.500” SBFS-3500 6.375” SBFS-6375
SBG Risers
3.625” SBFS-3625 6.500” SBFS-6500
3.750” SBFS-3750 6.600” SBFS-6600
3.976” SBFS-3976 6.750” SBFS-6750
4.000” SBFS-4000 6.860” SBFS-6860
4.160” SBFS-4160 6.950” SBFS-6950 SB-2200 with Riser
4.250” SBFS-4250 7.040” SBFS-7040
4.370” SBFS-4370 7.220” SBFS-7220
4.520” SBFS-4520 7.375” SBFS-7375
4.567” SBFS-4567 7.450” SBFS-7450

SBG-5000A, SBG-5000D & SBG-5000E Extension Shoes

The style of extension shoe depends on the diameter range being measured. Shoes are offered in
several lengths depending on the pitch of the stator lobes. It is important that the shoe length be long
enough to contact a minimum of two points on the bottom and one point on the top pad. Custom SBG-4500
shoes are available as special request. Contact Gagemaker for more infomation.

Model Description Range

SB-2100 8” long extension shoe 1.500” – 1.650”
SB-2110 8” long extension shoe 1.650” – 1.800”
SB-2120 8” long extension shoe 1.800” – 1.950”
SB-2200 20” extension shoe (requires riser) SBG-3500
SB-2150 .130” riser – SB-2200 extension shoe required 2.000” – 2.150”
SB-2300 .280” riser – SB-2200 extension shoe required 2.150” – 2.300”
SB-2400 .380” riser – SB-2200 extension shoe required 2.250” – 2.400”
SB-2500 .480” riser – SB-2200 extension shoe required 2.350” – 2.550”
SB-2600 .580” riser – SB-2200 extension shoe required 2.450” – 2.600”
SB-3500 20” extension shoe w/ brackets and adapter 2.600” – 3.500”
SB-4500 20” extension shoe w/ brackets and adapter 3.450” – 4.500”
SB-5500 20” extension shoe w/ brackets and adapter 4.450” – 5.500”
SB-6500 20” extension shoe w/ brackets and adapter 5.450” – 6.500”
SB-7500 20” extension shoe w/ brackets and adapter 6.450” – 7.500”

Phone: 713-472-7360 • Fax: 713-472-7241 141

 Gagemaker Products

Rotor Inspection
Today in the oil field industry, unique high-performance power sections require accurate measurement
tools for rotors and stators. Gagemaker has designed several gages to measure various parts of the
rotor.

Rotor Major Diameter Micrometer (T-MIC)

Due to high spirals on the lobes, conventional measurement gages cannot be used for measuring rotor
major diameters. Gagemaker developed the T-MIC to measure a rotor’s major diameter. The T-MIC’s
base spans across two lobes on one side of the centerline and uses a micrometer thimble on the other
to measure the diameter. Instead of modifying an existing micrometer, Gagemaker custom builds
each T-MIC. Gagemaker’s rugged design far exceeds all others on the market today. Special sizes are
available, contact customer service for more information. Special sizes, metric thimbles, and metric
sizes are available.

Range Model Description

6” Base 8” Base 12” Base 18” Base 24” Base
0" - 1" TM6-0-1 TM8-0-1 TM12-0-1 TM18-0-1 TM24-0-1
1" - 2" TM6-1-2 TM8-1-2 TM12-1-2 TM18-1-2 TM24-1-2
2" - 3" TM6-2-3 TM8-2-3 TM12-2-3 TM18-2-3 TM24-2-3
TM12-4-5
3" - 4" TM6-3-4 TM8-3-4 TM12-3-4 TM18-3-4 TM24-3-4
T-MIC for Rotor,
4" - 5" TM6-4-5 TM8-4-5 TM12-4-5 TM18-4-5 TM24-4-5
½" wide base
5" - 6" TM6-5-6 TM8-5-6 TM12-5-6 TM18-5-6 TM24-5-6
6" - 7" TM6-6-7 TM8-6-7 TM12-6-7 TM18-6-7 TM24-6-7
7" - 8" TM6-7-8 TM8-7-8 TM12-7-8 TM18-7-8 TM24-7-8
8" - 9" TM6-8-9 TM8-8-9 TM12-8-9 TM18-8-9 TM24-8-9

Rotor Major Diameter T-Micrometer with Digital Micrometer

Gagemaker also offers our T-MICs with digital micrometers. The digital micrometer can transfer your
data to a computer via the included SPC output. Special sizes, metric thimbles, and metric sizes
are available.

Range Model Description

6” Base 8” Base 12” Base 18” Base 24” Base
0" - 1" TM6-0-1-352 TM8-0-1-352 TM12-0-1-352 TM18-0-1-352 TM24-0-1-352

1" - 2" TM6-1-2-352 TM8-1-2-352 TM12-1-2-352 TM18-1-2-352 TM24-1-2-352

T-MIC for
2" - 3" TM6-2-3-352 TM8-2-3-352 TM12-2-3-352 TM18-2-3-352 TM24-2-3-352 Rotor,
TM12-2-3-352 3" - 4" TM6-3-4-352 TM8-3-4-352 TM12-3-4-352 TM18-3-4-352 TM24-3-4-352 ½” wide base
with a
4" - 5" TM6-4-5-352 TM8-4-5-352 TM12-4-5-352 TM18-4-5-352 TM24-4-5-352 Mitutoyo
50-352-10
5" - 6" TM6-5-6-352 TM8-5-6-352 TM12-5-6-352 TM18-5-6-352 TM24-5-6-352 digital microm-
6" - 7" TM6-6-7-352 TM8-6-7-352 TM12-6-7-352 TM18-6-7-352 TM24-6-7-352 eter and SPC
output
7" - 8" TM6-7-8-352 TM8-7-8-352 TM12-7-8-352 TM18-7-8-352 TM24-7-8-352

8" - 9" TM6-8-9-352 TM8-8-9-352 TM12-8-9-352 TM18-8-9-352 TM24-8-9-352

142 www.gagemaker.com • [email protected]

Rotor Minor Diameter Micrometer (MM)
Gagemaker’s minor diameter MIC gage was designed to measure a rotor’s minor diameter. The spiral
lobes on the rotor produce a valley, or minor diameter. The depth of the minor diameter from the
major diameter requires a 1” travel indicator stem. Gage range is 0” - 6”, which allows measuring
most rotor sizes with only one gage. Ensuring the gage’s durability and long life, Gagemaker’s design
uses a heavy duty indicator stem and bearing housing to withstand side loads. Special sizes are
available. MM-0-6

Model Description Range

MM-0-6 Minor diameter micrometer 0" - 6"

Core Alignment Gage

Verification that the core was properly placed when the stator was molded is easily checked using the
Core Alignment Gage. The gage is supplied with brass alignment inserts that match the thread of the
injection ports. The digital gage plunges a needle through the rubber to contact the core. Measurements
are made at 180° locations to verify that the core is indeed centrally located to the OD of the stator.

Model Description Range

CAW-2000 Core alignment gage 0” - 3”

Rotor Saddle Gage

The rotor saddle gage, also known as a rotor lobe height gage, is the last weapon in the inspection
arsenal. This gage sets on top of the spiral lobes of the rotor and measures the variation in lobe
height. Sliding the gage along the length of the rotor detects variation in root to crest height of all the
lobes. Measurements can be taken at 90° or 180° intervals to provide an accurate dimensional map CAW-2000
of the relationship between lobes. This inspection aids in manufacturing the rotor to specification.

Model Description Travel Pipe Diameter Range

RSG-7 Rotor saddle gage, 7” long 1” 1” - 4”
RSG-16 Rotor saddle gage, 16” long 1” 1” - 4”
RSG-24 Rotor saddle gage, 24” long 1” 1” - 4”

RSG-16

Phone: 713-472-7360 • Fax: 713-472-7241 143

 Gagemaker Products

Pin Seal Diameter Gages

The Pin Seal Diameter Series of gages inspect critical pin seal diameters and seal tapers on premium
connections. With the addition of stand-off plates, the gages also inspect seal tapers. Each model
PN-3001 covers a specific range of connection sizes, making the PN-3000 gages extremely versatile and
economical.

The PN-3000 gages use precision interchangeable contact points that position on the seal at a fixed
distance from the connection face during inspection.

Before inspecting parts, these gages must be preset to a nominal predetermined dimension using
gage blocks, Gagemaker’s Pin Seal Diameter Gage Setting Master, a MIC TRAC, or Frame Standards.

Features
• Provides accurate measurements on the gage’s indicator at the critical sealing point of the pin.
• Uses interchangeable contact points
• Inlcudes a .0005” resolution indicator.
• Requires presetting using gage blocks, Gagemaker’s Pin Seal Diameter Gage Setting Master, Frame
Standards, or MIC TRAC system.
• Allows use in a manufacturing or field environment due to durable construction

PN-3000 Series Pin Nose Diameter Gages*

View A. Customer to supply
standoff ("X")and point sizes ("T") The PN series measure pin nose diameter using contact points. Specify the distance from the face of
the connection to the measuring plane and desired contact point diameter when ordering.

Model Description Range

PN-3001 Pin Nose Diameter Gage 0” - 5½”
PNI-3001 PN-3002 Pin Nose Diameter Gage 0” - 9½”
PN-3003 Pin Nose Diameter Gage 0” - 13½”
PN-3004 Pin Nose Diameter Gage 0” - 19½”
PN-3005 Pin Nose Diameter Gage 0” - 25½”
*There is a separate cost to reposition the point standoff of PN-3000 Gages. Quotation available upon request.

PN-3000 Series Internal “Ball Contact” Seal Diameter Gages

The PNI series measure the internal ball contact seal diameter using contact points. Specify the
distance from the face of the connection to the measuring plane and desired contact point diameter
when ordering. Larger ranges may be available as a custom order.

Model Description Range

PNI-3001-VMB Internal “Ball Contact” Seal Diameter Gage 2” - 5½”
PNI-3002-VMB Internal “Ball Contact” Seal Diameter Gage 2” - 9⅝”
PNA-3001 PNI-3003-VMB Internal “Ball Contact” Seal Diameter Gage 2” - 13⅜”

PN-3000 Series 30° External Apex Diameter Gages

The PNA model gages measure only the external apex diameter of the connection. Larger ranges may
be available as a custom order.

Model Description Range

PNA-3001-VMA 30° External Apex Diameter Gage, Anvils 2” - 4¼”
PNA-3002-VMA 30° External Apex Diameter Gage, Anvils 2” - 9⅝”
PNA-3003-VMA 30° External Apex Diameter Gage, Anvils 2” - 13⅜”

144 www.gagemaker.com • [email protected]

PN-3000 Series 30° Internal/External Apex Seal Diameter Gages
The PN-3000 Series 30° Internal/External Apex Seal Diameter gages measure both the internal and
external diameters of the apex seal for the connection.

Model Description Range

Rotate the slider and keyway
PN-31VM-30 30° Internal/External Apex Seal Diameter “V” External 4"- 6⅝”, Internal 2⅜” - 6⅝” assembly for Internal/External
inspection
PN-33VM-30 30° Internal/External Apex Seal Diameter “V” External 4” - 14”, Internal 2⅜” - 14”

Pin Seal Diameter Gage Standoff Plates PN-31VM-30 Int./Ext.

PN-33VM-30 Int./Ext.

The pin seal standoff plates are available in various sizes. Additional custom sizes are available upon
request. Pin seal standoff plates are sold as a set of two.

Model Description Range

PN-3000/T.04087 Pin Seal Standoff Plate* 0.04087” (1.038 mm) thick
PN-3000/T.044 Pin Seal Standoff Plate* 0.0440” (1.12 mm) thick
PN-3000/T.0472 Pin Seal Standoff Plate* 0.0472” (1.20 mm) thick
PN-3000/T.0591 Pin Seal Standoff Plate* 0.0591” (1.50 mm) thick
PN-3000/T.064 Pin Seal Standoff Plate* 0.0640” (1.62 mm) thick
PN-3000/T.072 Pin Seal Standoff Plate* 0.0720” (1.83 mm) thick
PN-3000/T.0748 Pin Seal Standoff Plate* 0.0748” (1.90 mm) thick
PN-3000/T.078 Pin Seal Standoff Plate* 0.0780” (1.9812 mm) thick
PN-3000/T.0787 Pin Seal Standoff Plate* 0.0787” (2.00 mm) thick
PN-3000/T.0811 Pin Seal Standoff Plate* 0.0811” (2.06 mm) thick
PN-3000/T.0815 Pin Seal Standoff Plate* 0.0815” (2.07 mm) thick
PN-3000/T.094 Pin Seal Standoff Plate* 0.0940” (2.39 mm) thick
PN-3000/T.100 Pin Seal Standoff Plate* 0.1000” (2.54 mm) thick
PN-3000/T.114 Pin Seal Standoff Plate* 0.1140” (2.90 mm) thick
PN-3000/T.1181 Pin Seal Standoff Plate* 0.1181” (3.00 mm) thick Customer to specify
thickness ("T")
PN-3000/T.121 Pin Seal Standoff Plate* 0.1210” (3.07 mm) thick of taper plates
PN-3000/T.122 Pin Seal Standoff Plate* 0.1220” (3.10 mm) thick
PN-3000/T.1378 Pin Seal Standoff Plate* 0.1378” (3.50 mm) thick
PN-3000/T.171 Pin Seal Standoff Plate* 0.1710” (4.34 mm) thick
PN-3000/T.1969 Pin Seal Standoff Plate* 0.1969” (5.00 mm) thick
PN-3000/T.200 Pin Seal Standoff Plate* 0.2000” (5.08 mm) thick
PN-3000/T.3149 Pin Seal Standoff Plate* 0.3149” (8.00 mm) thick PN-3000/T
PN-3000/T.350 Pin Seal Standoff Plate* 0.3500” (8.89 mm) thick Pin Seal
Standoff Plate
*Additional plate thickness sizes are available. All plates are two per set.

The round and frame style standards are designed to

preset all models of the PN-3000 series gages for
accurate inspection of API pin end seal taper diameters
of premium connections. These standards consist of a
rigid, non-adjustable steel block machined to precise,
proper size tolerances.

Phone: 713-472-7360 • Fax: 713-472-7241 145

 Gagemaker Products

Back-of-Box Gage
Back-of-Box gage measures coupling and box seal diameters. Gage must be preset with a standard.
For standards, please call for a quotation.

Model Description Range

BB-7000 Back-of-Box Seal Diameter Gage 3.915” - 11.965”

Internal Diameter/Groove Gages

Gagemaker’s internal diameter and groove gages measure variation in internal bore diameters.
Diameter/groove gages are shipped with two .072” diameter contact points (T072) as standard. Refer
BB-7000
to the contact point pages 124-125 for the proper contact point for your particular application.

Model Description Range

IT-5104 Internal Diameter/Groove Gage 4” Depth, 1½” - 10” Dia.

IT-5106 Internal Diameter/Groove Gage 6” Depth, 1½” - 10” Dia.

IT-5106-30 Int. Diameter/Groove Gage, points at 30° angle 6” Depth, 1½” - 10” Dia.

IT-5106-45 Int. Diameter/Groove Gage, points at 45° angle 6” Depth, 1½” - 10” Dia.

IT-5108 Internal Diameter/Groove Gage 8” Depth, 1½” - 10” Dia.

IT-5112 Internal Diameter/Groove Gage 12” Depth, 1½” - 10” Dia.

Internal Diameter/Groove Gage Replacement Parts

Model Description Length

BB-7000 Extensions
IT-5104-04 Replacement Lower Arm 4¼”

IT-5106-06 Replacement Lower Arm 6”

IT-5108-08 Replacement Lower Arm 8”

IT-5112-12 Replacement Lower Arm 12”

IT-5104

146 www.gagemaker.com • [email protected]

Pipe Straightness Gages
Saddle Gage SG-8001

The Saddle Gage measures the amount of hook or bend at the end of a joint of pipe. The SG-8001
uses the RC-375 roller contact.

Model Description Range

SG-8001 Saddle Gage All Sizes
SG-8001-TA SG-8001 Tube Assembly
RC-375 0.375” Diameter Roller Contact

Squareness Gage
The SQ-1600 Squareness gage monitors the alignment of weld-on connectors to the pipe body.
Requires setting by a qualified standard. The SQ-1630S, our precision calibration square, is strongly SQ-1648
recommended for best results. Standard sold separately.

Model Description Range SQ-1636S

SQ-1636 Squareness Gage, 30” reach Up to 36” diameter

SQ-1648 Squareness Gage, 30” reach Up to 48” diameter
SQ-1636S Squareness Gage Standard 14” X 36” Square

Straight Edge Gage SQ-1636

The SE-1000 Straight Edge gage measures the straightness of well tubing and casing. The gage
price includes an SES-1000 Standard. Replacement standards are available.

Model Description Range

SE-1000 Straight Edge 36” - 64”
SES-1000 Replacement Straight Edge Standard SE-1000

Laser Alignment Gage

The Laser Alignment Gage ensures proper angular and parallel alignment during assembly of weld-on
connectors. Replacement parts are available.

SES-1000
Model Description Inside Diameter Range Outside Diameter Range
LA-3600 Laser Alignment Gage 11” - 55” 8” - 50”

Ovality Gage
Ovality gages are designed to check the out-of-round condition of tubular goods prior to processing.
Gagemaker’s OV-9800 series offers diameter adjustability within a size range. Stabilizing rollers are
adjustable for diameter as well as for alignment to the centerline.

Model Description Range LA-3600

OV-9801 Ovality Gage, pipe ovality 2” - 6”

OV-9802 Ovality Gage, pipe ovality 6” - 10”
OV-9803 Ovality Gage, pipe ovality 10“ - 14”
OG-9801

Phone: 713-472-7360 • Fax: 713-472-7241 147

 Gagemaker Products

Shoulder Location Gages

Depth Gages
DG-1008 Our digital depth gages inspect the location of internal and external shoulders and grooves from the
face of pin and box connections or other datum surfaces. The DG-1000 Series is available with the
standard base, a 12” base, and a 20” base. These gages are available in ranges: 0”-8”, 0”-12”, 0”-18”,
and 0”-24”.

The standard gage (DG-1000 Series) is supplied with a 7” extension arm and a 0° and 45° contact
point holder for use with any #4-48 threaded contact point (one .072” contact point (T072) supplied
unless otherwise requested). Longer extension arms and other contact point configurations and
adapters are available upon request. The 12” (DG-1200 Series) and 20” (DG-2000 Series) gages
include one double sided blade contact instead of a contact point and a contact point holder.

Digital depth gages do not require a setting standard. The gage is preset to zero on any flat surface
and then applied to the product. Actual length measurements display on the gage’s digital readout.

Features
• Inspects internal and external shoulder and groove locations.
DG-1008 with • Uses an interchangeable contact point or blade that can service many different applications.
DG-1000-R7
Extension Arm
• Inch/metric conversion with digital readout
• Digital readout with .0005”/.01 mm resolution and SPC Output

Model Description Range

Depth Gage with Digital Display (in/mm)
DG-1208
DG-1008 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution 0” - 8”
DG-1012 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution 0” - 12”
DG-1018 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution 0” - 18”
DG-1024 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution 0" - 24"
Depth Gage with Digital Display and 12” Base (in/mm)
DG-1208 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution, 12" base 0” - 8”
DG-1212 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution, 12" base 0” - 12”
DG-1218 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution, 12" base 0” - 18”
DG-1224 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution, 12" base 0” - 24”
Depth Gage with Digital Display (in/mm) and 20” Base (in/mm)
DG-2012 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution, 20" base 0” - 12”
DG-1012 with DG-2018 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution, 20" base 0” - 18”
DG-1000-R36 Stabilzer
DG-2024 Depth Gage w/ digital display (in/mm), .0005”/.01 mm resolution, 20" base 0” - 24”
Depth Gage Accessories
DG-1000-R7 7” Extension Arm
DG-1000-R16 16” Extension Arm
DG-1000-R24 24” Extension Arm
DG-1000-R36 Stabilizer for larger diameters 36" & Larger
DG-DSB-1824 DG-DSB-812
DG-1000-BPA DG-1000 Base Plate Assembly
DG-1212-DF Shoulder Location Double Foot for DG-1208 and DG-1212
DG-1218-DF Shoulder Location Double Foot for DG-1218 and DG-1224
DG-B-812 Blade Contact for 8 and 12 inch ranges for DG-1200/2000 8 & 12
DG-P45-1824 DG-P45-812 DG-B-1824 Blade Contact for 18 and 24 inch ranges for DG-1200/2000 18 & 24
DG-DSB-812 Double Sided Blade Contact for 8 and 12 inch range DG-1200/2000 8 & 12
DG-DSB-1824 Double Sided Blade Contact for 18 and 24 inch range DG-1200/2000 18 & 24
DG-GV-812 Groove Locator, .100” thick for DG-1008 and DG-1012 8 & 12
DG-GV-1824 DG-GV-812 DG-GV-1824 Groove Locator, .100” thick for DG-1018 and DG-1024 18 & 24
DG-P45-812 45° Point Holder for DG-1008 and DG-1012 8 & 12
DG-P45-1824 45° Point Holder for DG-1018 and DG-1024 18 & 24

148 www.gagemaker.com • [email protected]

Torque Shoulder Gages and Standards
Both the TS-1000 and TS-4000 series of gages accurately measure the distance between the primary
and secondary torque shoulders on both internal and external threaded connections. Used industry
wide to measure the shoulder-to-shoulder distance on premium tool joints and the face-to-seal
location on premium couplings, Gagemaker TS gages are also perfectly suited to locate grooves from TS-1000
various datum surfaces.

The TS gages require a setting standard. The gage is preset to the desired dimension and deviation is
read from the gage’s dial indicator.

The TS-1000 is supplied with a 6” extension arm. A 45° contact point holder for use with any #4-48
threaded contact point is also supplied. Longer extension arms, other contact points, and
adapters are available upon request.

Features
• Inspects internal and external shoulder and groove locations
• Uses an interchangeable contact point that can service many different applications

Model Description Range

TS-1000 Shoulder Depth Gage, Base length 6” 1” - 6”
TS-1000-1 Shoulder Depth Gage, Base length 6”, .0001” Indicator 1” - 6” TSS-1000

TS-1001 Shoulder Depth Gage, Base length 12” 1” - 10”

TS-1001-1 Shoulder Depth Gage, Base length 12”, .0001” Indicator 1” - 10”
TS-4000 Shoulder Depth Gage (Specify Taper) 2⅜” & Larger
TSS-1000 TS-1000 Setting Standard
TSS-4000 TS-4000 Setting Standard

Thread Data TS-4000

Thread Data Chart

The Gagemaker API Thread Data Chart provides critical thread data per API Specification 5B.

Model Description Connections

API Tubing and Casing Thread Dimension 2⅜” - 20” 8-Round, LTC, STC
Thread Data Chart
Slide Chart 4½” - 20” Buttress

TSS-4000

Thread Data Chart

Phone: 713-472-7360 • Fax: 713-472-7241 149

 Gagemaker Products

Specialty Items
CA-9001
Coupling Alignment
The Coupling Alignment gage ensures that the threads on both ends of the coupling are properly
aligned with each other.

Model Description Range

CA-9001 Coupling Alignment Gage 2⅜” & Larger

Internal Deep Reach Bore Gages

DB-1800 The DB series of gages are internal deep reach bore gages. Internal deep reach bore gages allow the
difficult measuring of pitch diameter deep inside a small diameter product. One set of contact points
and one set of extension rods are included.

Model Description Range

DB-1800 Internal Deep Reach Bore Gage, 18” reach min. bore 1.700”
DB-2400 Internal Deep Reach Bore Gage, 24” reach min. bore 1.700”

PD-3003
Pit Depth Gages
The PD-3000 series of gages inspect the depth of surface pitting on tubular goods. The gage also
accepts other types and sizes of contact points for use in other applications, such as groove and
thread depth inspection. Select the PD-3000 gage model based on the type of indicator required.

PD-3004 Model Description Range

PD-3003 Pit Depth Gage, AGD #1, 0-100 .250
PD-3004 Pit Depth Gage, AGD #2, 0-100 .450
PD-3005 Pit Depth Gage w/ Flat Base, AGD #2, 0-100 .450
PD-3006 Pit Depth Gage w/ 6" Long Flat Base, AGD #2, 0-100 .450
PD-3005 PD-3007 Pit Depth Gage w/ 6" Long V Base, AGD #2, 0-100 .450
PD-3000BF Pit Depth Flat Base Only
PD-3000BV Pit Depth V Base Only
PD-3000BF-6 Pit Depth 6" Long Flat Base Only
PD-3000BF-10 Pit Depth 10" Long Flat Base Only
PD-3000BV-6 Pit Depth 6" Long V Base Only

PD-3004-6 Power Tight Make-up Gage

The Power Tight Make-up Gage, PT-4000, adjusts to determine the proper make-up location of API
couplings.
PD-3000BF-6
Model Description Range
PT-4000 Power Tight Make-up Gage All Sizes

Standoff Gages
PT-4000
The ST-7001 measures variation in ring and plug gage standoff on rotary shouldered connections.
The ST-7001 is supplied with a setting standard. The ST-7002 is set on any qualified surface.

ST-7001
Model Description Range
ST-7001 Indicator Standoff Gage w/ Setting Standard .615” - .635”
ST-7002 RSC Box Standoff Gage to measure plug stand-in, .0005” resolution 0” - .01” stand-in
STS-7001 STS-7001 Setting Standard Replacement, .625" width
ST-7002

150 www.gagemaker.com • [email protected]

Wall Thickness Gages
The WT-9000 series of gages measures wall thickness at specific distances from the end of the pipe.
Specify the distance from the end of the pipe to the measuring plane when ordering.

Model Description Range

WT-9001 Wall Thickness Gage 2⅜” - 4½”
WT-9002 Wall Thickness Gage 4½” - 9⅝”
WT-9003 Wall Thickness Gage 4½” - 13⅜”
WT-9001
Gage Storage Cases
Gagemaker promotes three types of gage storage cases in various sizes- heavy-duty, standard, and
wooden. The two plastic types are constructed of durable ABS molded plastic material.

The PEL Series of heavy-duty plastic cases, manufactured by Pelican, are extremely sturdy and can
be used to ship and store gages. These cases not only provide extra protection for gages, but they are
watertight, airtight, dustproof, and crushproof.

The CASE Series are our standard plastic cases. They are constructed from durable ABS molded
plastic. These cases are low impact resistant and lightweight.
PEL
Series
The WOOD Series of cases is our line of rugged, handcrafted wooden cases. If necessary, wooden
cases can be customized to your specifications.

All storage cases are available with foam inserts at additional cost. Also, foam inserts can be custom
cut for any of our products. Custom cutting of foam for cases is priced on an hourly basis. Please
call for a quotation.

WOOD
Model Inside Measurements Model Inside Measurements Series
PEL-1400 12¼” X 9¼” X 5¼” PEL-1600 22” X 17” X 8”
PEL-1450 15” X 10⅜” X 6“ PEL-1700 36” X 13½” X 5”
PEL-1500 17⅞” X 11¾” X 6⅛” PEL-1750 50¾” X 13½” X 5”
PEL-1550 19⅞” X 13¼” X 7¾”

Model Inside Measurements Model Inside Measurements

CASE-1 16” X 11” X 3” CASE-5 21½” X 14½” X 6⅝”
CASE-2 14” X 10” X 3” CASE-6 8⅝” X 5⅝” X 3⅛" CASE
Series
CASE-3 9” X 12½” X 2¾” CASE-7 21" X 14" X 6"
CASE-4 7” X 4” X 2”

Model Inside Measurements Model Inside Measurements

WOOD-A 54" X 17" X 3½" WOOD-J 27" X 10" X 3.5" Foam
WOOD-B 48" X 10" X 3½" WOOD-J-1 27" X 9" X 3½” Inserts

WOOD-B-1 46" X 26" X 3½" WOOD-K 26" X 15" X 3½”

WOOD-C 44" X 8" X 3½” WOOD-L 25" X 10" X 3½"
WOOD-D 42" X 24" X 3½” WOOD-M 22" X 12" X 3½”
WOOD-E 42" X 10" X 3½” WOOD-N 22" X 8" X 3½"
WOOD-F 35" X 12" X 3½” WOOD-O 21" X 8" X 3½"
WOOD-G 34" X 10" X 3½” WOOD-P 17" X 10" X 3½"
WOOD-H 34" X 8" X 3½" WOOD-Q 15" X 15" X 3½"
WOOD-I 33" X 21" X 3½”

Custom Cut
Foam

Phone: 713-472-7360 • Fax: 713-472-7241 151