SECTION 2 STRUCTURE AND FUNCTION

GROUP 1 PUMP DEVICE

1. STRUCTURE
The pump device consists of main pump, regulator and gear pump.

Port Port name Port size

A1,2 Delivery port SAE6000psi 3/4"
B1 Suction port SAE2500psi 2 1/2"
Dr Drain port PF 1/2 - 19
Pi1,i2 Pilot port PF 1/4 - 15
P1 EPPR port PF 1/4 - 13
a1,2 Gauge port PF 1/4 - 15
a3 Gauge port PF 1/4 - 14
a4 Gauge port PF 1/4 - 13
A3 Gear pump delivery port PF 1/2 - 19
B3 Gear pump suction port PF 3/4 - 20.5
11072PM01

2-1
1) MAIN PUMP(1/2)
The main pump consists of two piston pumps(front & rear) and valve block.

702
789, 732 532 214 548 531 724 792 534 901 954 719 151 152 211 113

535
808

953
886 04
717
406
261
774

111
824
127
710
123
251

212
490 153 156 157 313 124 312 114 466 885 314 467 141 981 271 401
725 728 983
14072SF02

04 Gear pump 271 Pump casing 719 O-ring

111 Drive shaft(F) 312 Valve block 724 O-ring
113 Drive shaft(R) 313 Valve plate(R) 725 O-ring
114 Spline couping 314 Valve plate(L) 728 O-ring
123 Roller bearing 401 Hexagon socket bolt 732 O-ring
124 Needle bearing 406 Hexagon socket bolt 774 Oil seal
127 Bearing spacer 466 VP Plug 789 Back up ring
141 Cylinder block 467 VP Plug 792 Back up ring
151 Piston 490 Plug 808 Hexagon head nut
152 Shoe 531 tilting pin 824 Snap ring
153 Set plate 532 Servo piston 885 Pin
156 Bushing 534 Stopper(L) 886 Spring pin
157 Cylinder spring 535 Stopper(S) 901 Eye bolt
211 Shoe plate 548 Pin 953 Set screw
212 Swash plate 702 O-ring 954 Set screw
214 Bushing 710 O-ring 981 Plate
251 Support 717 O-ring 983 Pin
261 Seal cover(F)

2-2
 2) REGULATOR(1/2)

412 875 874

755
A
897 858
B
614
612

438

615 801
613
924
A 611
B
641 730 643 708 644 645 646 728

SECTION B-B

413 438 405 413 438

438

735

656 D

722 496 724 725 436 699 496 724 725 436

VIEW C(FRONT) VIEW C(REAR)

KR36-9N12(FRT) A
KR36-9N1S(RR)

735 722 P2
079
Pf
466
Port Port name port size
Pi
A Delivery port 3/4"

753
B Suction port 2 1/2"
496 755
SECTION D-D Pn Pilot port PF 1/4-15
Pm Qmax cut port PF 1/4-15
B

11072PM03

2-3
 REGULATOR(2/2)

734 653 654 836 651 652 601 624 629 630 628
655

641 801
C
814 925

898

631 627

732

733
732

622

621 623 625 626 887 763 756

140LC-7 ‫׆‬೴ 2-5
SECTION A-A

405 Hexagon socket screw 629 Cover(C) 730 O-ring

412 Hexagon socket screw 630 Lock nut 732 O-ring
413 Hexagon socket screw 631 Sleeve, pf 733 O-ring
436 Hexagon socket screw 641 Pilot cover 734 O-ring
438 Hexagon socket screw 643 Pilot piston 735 O-ring
466 Plug 644 Spring seat(Q) 753 O-ring
496 Plug 645 Adjust stem(Q) 755 O-ring
601 Casing 646 Pilot spring 756 O-ring
611 Feed back lever 651 Sleeve 763 O-ring
612 Lever(1) 652 Spool 801 Nut
613 Lever(2) 653 Spring seat 814 Snap ring
614 Fulcrum plug 654 Return spring 836 Snap ring
615 Adjust plug 655 Set spring 858 Snap ring
621 Compensator piston 656 Block cover 874 Pin
622 Piston case 699 Valve casing 875 Pin
623 Compensator rod 708 O-ring 887 Pin
624 Spring seat(C) 722 O-ring 897 Pin
625 Outer spring 724 O-ring 898 Pin
626 Inner spring 725 O-ring 924 Set screw
627 Adjust stem(C) 728 O-ring 925 Adjust screw(QI)
628 Adjust screw(C)

2-4
3) GEAR PUMP

700 354 351 433

B3

850
355
434
A3
311

312
a3

710 435 361 353 732 309 307 310 308 434 466, 725

140LC-7 ‫׆‬೴ 2-5

307 Poppet 353 Drive gear 466 Plug

308 Seat 354 Driven gear 700 Ring
309 Spring seat 355 Filter 710 O-ring
310 Spring 361 Front case 725 O-ring
311 Screw 433 Flange socket 732 O-ring
312 Nut 434 Flange socket 850 Snap ring
351 Gear case 435 Flange socket

2-5
2. FUNCTION
1) MAIN PUMP
The pumps may classified roughly into the rotary group performing a rotary motion and working as
the major part of the whole pump function: the swash plate group that varies the delivery rates: and
the valve cover group that changes over oil suction and discharge.

(1) Rotary group

The rotary group consists of drive shaft
(F)(111), cylinder block(141), piston
shoes(151,152), set plate(153), spherical
bush(156) and cylinder spring(157).
The drive shaft is supported by bearing
(123,124) at its both ends.
The shoe is caulked to the piston to from a
spherical coupling. It has a pocket to
relieve thrust force generated by loading
pressure and the take hydraulic balance
so that it slides lightly over the shoe
plate(211). The sub group composed by
a piston and a shoe is pressed against the
shoe plate by the action of the cylinder
spring via a retainer and a spherical bush.
Similarly, the cylinder block is pressed 14072SF04
against valve plate(313) by the action of
the cylinder spring.
(2) Swash plate group 531
The swash plate group consists of swash 548
plate(212), shoe plate(211), swash plate 214
support(251), tilting bush(214), tilting
212
pin(531) and servo piston(532).
The swash plate is a cylindrical part 251
211
formed on the opposite side of the sliding
surface of the shoe and is supported by
the swash support.
If the servo piston moves to the right and
532 ɷ
left as hydraulic force controlled by the
regulator is admitted to hydraulic chamber
located on both sides of the servo piston,
the swash plate slides over the swash ɷ
plate support via the spherical part of the
tilting pin to change the tilting angle(ɷ)

140LC-7 ‫׆‬೴ 2-7

2-6
(3) Valve block group
The valve block group consists of valve
block(312), valve plate(313) and valve
plate pin(885).
The valve plate having two melon-shaped
ports is fixed to the valve block and feeds 312
and collects oil to and from the cylinder
block. 313
885
The oil changed over by the valve plate is
connected to an external pipeline by way
of the valve block.
Now, if the drive shaft is driven by a prime
mover(electric motor, engine, etc), it
rotates the cylinder block via a spline
linkage at the same time. If the swash
plate is tilted as in Fig(previous page) the
pistons arranged in the cylinder block 140LC-7 ‫׆‬೴ 2-8

make a reciprocating motion with respect

to the cylinder block, while they revolve
with the cylinder block.
If you pay attention to a single piston, it
performs a motion away from the valve
plate(oil sucking process) within 180
degrees, and makes a motion towards the
valve plate(or oil discharging process) in
the rest of 180 degrees. When the swash
plate has a tilting angle of zero, the piston
makes no stroke and discharges no oil.

2-7
2) REGULATOR
Regulator consists of the negative flow control, total horse power control and power shift control
function.

(1) Negative flow control

By changing the pilot pressure Pn, the
pump tilting angle(delivery flow) is
regulated arbitrarily, as shown in the
figure.
This regulator is of the negative flow

Delivery flow, Q
control in which the delivery flow Q
decreases as the pilot pressure Pn rises.
With this mechanism, when the pilot
pressure corresponding to the flow
required for the work is commanded, the
pump discharges the required flow only,
and so it does not consume the power Pilot pressure, Pn
uselessly.

2-8
Η Flow reducing function

643 654 651 652 613 646

P1 CL
B(E)
874
897
C
A

875
611

Servo piston Small diameter

D
Large diameter chamber
chamber 548
531

11072PM10

As the pilot pressure Pn rises, the pilot piston(643) moves to the right to a position where the
force of the pilot spring(646) balances with the hydraulic force.
The groove(A) in the pilot piston is fitted with the pin(875) that is fixed to lever 2(613). Therefore,
when the pilot piston moves, lever 2 rotates around the fulcrum of point B [fixed by the fulcrum
plug(614) and pin(875)]. Since the large hole section(C) of lever 2 contains a protruding
pin(897) fixed to the feedback lever(611), the pin(897) moves to the right as lever 2 rotates.
Since the opposing-flat section(D) of the feedback lever is fitted with the pin(548) fixed by the
tilting pin(531) that swings the swash plate, the feedback lever rotates around the fulcrum of point
D, as the pin(897) moves.
Since the feedback lever is connected with the spool(652) via the pin(874), the spool moves to
the right.
The movement of the spool causes the delivery pressure P1 to connect to port CL through the
spool and to be admitted to the large diameter section of the servo piston. The delivery
pressure P1 that is constantly admitted to the small diameter section of the servo piston moves
the servo piston to the right due to the area difference, resulting in decrease of the tilting angle.
When the servo piston moves to the right, point D also moves to the right. The spool is fitted
with the return spring(654) and is tensioned to the left at all times, and so the pin(897) is pressed
against the large hole section(C) of lever 2.
Therefore, as point D moves, the feedback lever rotates around the fulcrum of point C, and the
spool is shifted to the left. This causes the opening between the sleeve(651) and spool(652) to
close slowly, and the servo piston comes to a complete stop when it closes completely.

2-9
Θ Flow increasing function

643 654 651 652 613 646

P1 CL
B(E)
874
897
C

875

611

Servo piston D Small diameter

Large diameter 548 chamber
chamber
531

11072PM11

As the pilot pressure Pn decreases, the pilot piston(643) moves to the left by the action of the
pilot spring(646) and causes lever 2(613) to rotate around the fulcrum of point B. Since the
pin(897) is pressed against the large hole section(C) of lever 2 by the action of the return
spring(654) via the spool(652), pin(874), and feedback lever(611), the feedback lever rotates
around the fulcrum of point D as lever 2 rotates, and shifts the spool to the left. Port CL opens a
way to the tank port as the spool moves. This deprives the large diameter section of the servo
piston of pressure, and shifts the servo piston to the left by the discharge pressure P1 in the
small diameter section, resulting in an increase in the flow rate.
As the servo piston moves, point D also moves to the left, the feedback lever rotates around the
fulcrum of point C, and the spool moves to the right till the opening between the spool and sleeve
is closed.

2-10
Ι Adjustment of flow control characteristic
The flow control characteristic can be
adjusted with the adjusting screw.
Adjust it by loosening the hexagon 801
nut(801) and by tightening(or loosening) 924
the hexagonal socket head screw(924).
Tightening the screw shifts the control
chart to the right as shown in the figure.
ö Adjusting values are shown in table.
Adjustment of flow control
characteristic 140LC-7 ‫׆‬೴ 2-12
Speed
Tightening Flow control Flow change
amount of starting amount
adjusting pressure
screw(924) change

Delivery flow, Q
amount

(min -1) (Turn) (kgf/cm2) (˶/min)

1950 +1/4 +1.5 +7.3

Pilot pressure, Pn

2-11
(2) Total horsepower control

The regulator decreases the pump tilting

angle(delivery flow) automatically to limit
the input torque within a certain value with

Delivery flow, Q
a rise in the delivery pressure P1 of the
self pump and the delivery pressure P2 of
the companion pump.
(The input horsepower is constant when
the speed is constant.)
Since the regulator is of the simultaneous
Delivery pressure, (P1+P2)
total horsepower type that operates by the
sum of load pressures of the two pumps
in the tandem double-pump system, the
prime mover is automatically prevented
from being overloaded, irrespective of the
load condition of the two pumps, when
horsepower control is under way.
Since this regulator is of the simultaneous
total horsepower type, it controls the tilting
angles(displacement volumes) of the two
pumps to the same value as represented
by the following equation :
Tin = P1Ýq/2ӕ + P2Ýq/2ӕ
= (P1+P2)Ýq/2ӕ
The horsepower control function is the
same as the flow control function and is
summarized in the following.(For detailed
behaviors of respective parts, refer to the
section of flow control).

2-12
Η Overload preventive function

621 651 652 623 612 601 625 626

P1 CL
B(E)
897

P2 P1
875

611

Large diameter Servo piston

chamber Small diameter
D chamber

140LC-7 ‫׆‬೴ 2-14

When the self pump delivery pressure P1 or the companion pump delivery pressure P2 rises, it
acts on the stepped part of the compensating piston(621). It presses the compensating rod(623)
to the right till the force of the outer spring(625) and inner spring(626) balances with the hydraulic
force. The movement of the compensating rod is transmitted to lever 1(612) via pin(875).
Lever 1 rotates around the pin(875) (E) fixed to the casing(601).
Since the large hole section(F) of lever 1 contains a protruding pin(897) fixed to the feedback
lever(611), the feedback lever rotates around the fulcrum of point D as lever 1 rotates, and then
the spool(652) is shifted to the right. As the spool moves, the delivery pressure P1 is admitted to
the large diameter section of the servo piston via port CL, causes the servo piston move to the
right, reduces the pump delivery, flow rate, and prevents the prime mover from being overloaded.
The movement of the servo piston is transmitted to the feedback lever via point D. Then the
feedback lever rotates around the fulcrum of point F and the spool is shifted to the left. The
spool moves till the opening between the spool(652) and sleeve(651) is closed.

2-13
Θ Flow reset function

621 651 652 623 612 601 625 626

P1 CL
B(E)
897

P2 P1

875

Large diameter Small diameter

chamber Servo piston D chamber

140LC-7 ‫׆‬೴ 2-15

As the self pump delivery pressure P1 or the companion pump delivery pressure P2 decreases,
the compensating rod(623) is pushed back by the action of the springs(625 & 626) to rotate lever
1(612) around point E. Rotating of lever 1 causes the feedback lever(611) to rotate around the
fulcrum of point D and then the spool(652) to move to the left. As a result, port CL opens a way
to the tank port.
This causes the servo piston to move to the left and the pump's delivery rate to increase.
The movement of the servo piston is transmitted to the spool by the action of the feedback
mechanism to move it till the opening between the spool and sleeve is closed.

2-14
Ι Low tilting angle(Low flow) command preferential function
As mentioned above, flow control and horsepower control tilting angle commands are transmitted
to the feedback lever and spool via the large-hole sections(C & F) of levers 1 and 2. However,
since sections C and F have the pins(͚4) protruding from the large hole(͚8), only the lever
lessening the tilting angle contacts the pin(897) ; the hole(͚8) in the lever of a larger tilting angle
command is freed without contacting the pin(897). Such a mechanical selection method permits
preference of the lower tilting angle command of the flow control and horsepower control.
Κ Adjustment of input horsepower
Since the regulator is of total cumulative horsepower type, adjust the adjusting screws of both the
front and rear pumps, when changing the horsepower set values. The pressure change values
by adjustment are based on two pumps pressurized at the same time, and the values will be
doubled when only one pump is loaded.

a. Adjustment of outer spring

625 626 630 628
Adjust it by loosening the hexagon
nut(630) and by tightening(or loosening)
the adjusting screw C(628). Tightening
the screw shifts the control chart to the 801
right and increases the input horsepow-
925
er as shown in the figure. Since turning
the adjusting screw C by N turns
changes the setting of the inner
spring(626), return the adjusting screw
QI(925) by NÝA turns at first.(A=1.9)
ö Adjusting values are shown in table
140LC-7 ‫׆‬೴ 2-16
Adjustment of outer spring
Speed
Tightenin Compens- Input torque
amount of ationg control change
adjusting pressure amount
Delivery flow, Q

screw(C) change
(924) amount

(min -1) (Turn) (kgf/cm2) (kgfÂm)

1950 +1/4 +19.2 +2.71

Delivery pressure, (P1+P2)

2-15
b. Adjustment of inner spring 626
Adjust it by loosening the hexagon nut
(801) and by tightening(or loosening)
the adjusting screw QI(925). 801
Tightening the screw increases the flow
and then the input horsepower as 925
shown in the figure.
ö Adjusting valves are shown in table
Adjustment of outer spring
Speed
Tightenin Flow Input torque
amount of change change
140LC-7 ‫׆‬೴ 2-17
adjusting amount amount
screw(C)
(925)

Delivery flow, Q
(min -1) (Turn) (˶/min) (kgfÂm)

1950 +1/4 +5.2 +2.3

Delivery pressure, (P1+P2)

2-16
(3) Power shift control

621 651 652 623 612 625 626

898 P1 CL
B(E)
897

Pf
P2 P1
875

611

Large diameter Small diameter

chamber Servo piston D chamber

140LC-7 ‫׆‬೴ 2-18

The set horsepower valve is shifted by

varying the command current level of the
proportional pressure reducing valve
Delivery flow, Q

attached to the pump.

Only one proportional pressure reducing Pf=
valve is provided. MIN
Pf= .
However, the secondary pressure Pf MA
X.
(power shift pressure) is admitted to the
horsepower control section of each pump
Delivery pressure, (P1+P2)
regulator through the pump's internal path
to shift it to the same set horsepower
level.
This function permits arbitrary setting of the pump output power, thereby providing the optimum
power level according to the operating condition.
The power shift pressure Pf controls the set horsepower of the pump to a desired level, as shown
in the figure.
As the power shift pressure Pf rises, the compensating rod(623) moves to the right via the
pin(898) and compensating piston(621).
This decreases the pump tilting angle and then the set horsepower in the same way as explained
in the overload preventive function of the horsepower control. On the contrary, the set horsepower
rises as the power shift pressure Pf falls.

2-17
(4) Adjustment of maximum and minimum flows
808
Η Adjust it by loosening the hexagon
nut(808) and by tightening(or loosening)
954
the set screw(954).
The maximum flow only is adjusted
without changing other control
characteristics.
140LC-7 ‫׆‬೴ 2-19(1)
Adjustment of max flow
Speed
Tightening Flow change
amount of amount
adjusting screw

Delivery flow, Q
(954)

(min -1) (Turn) (˶/min)

1950 +1/4 -3.1

Delivery pressure, Pn

Θ Adjustment of minimum flow

Adjust it by loosening the hexagon
806
nut(808) and by tightening(or loosening)
the hexagonal socket head set screw
953
(953). Similarly to the adjustment of the
maximum flow, other characteristics are
not changed.
However, remember that, if tightened too
140LC-7 ‫׆‬೴ 2-19(2)
much, the required horsepower during
the maximum delivery pressure(or during
relieving) may increase.
Adjustment of min flow
Delivery flow, Q

Speed
Tightening Flow change
amount of amount
adjusting screw
(953)

(min -1) (Turn) (˶/min)

1950 +1/4 +3.1 Delivery pressure, Pn

2-18