FlightManual Calidus 2-1 ENG

Flight and Operation Manual
for Gyroplane Calidus
AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Pre-pages 1

INTENTIONALLY LEFT BLANK

Flight and Operation Manual for Gyroplane
Calidus
Model: ______________________________________________
Serial number: ______________________________________________
Registration: ______________________________________________
Type certificate number: ______________________________________________
Aircraft manufacturer and

type certificate holder: AutoGyro GmbH
Dornierstraße 14
D-31137 Hildesheim
Tel.: +49 (0) 51 21 / 8 80 56-00
Fax: +49 (0) 51 21 / 8 80 56-19
Distribution partner: ______________________________________________
______________________________________________
______________________________________________
Owner: ______________________________________________
______________________________________________
______________________________________________
This flight manual is always to be carried on board of the aircraft and must be kept in
current, up-to-date status. The latest revisions and version status is available at www.auto-
gyro.com. Extent and revision status of the manual is recorded in the revision log and the
table of content.
This gyroplane may be operated only in strict compliance with the limitations and
procedures contained in this manual.
The manual is not a substitute for competent theoretical and practical training on the
operation of this aircraft. Failure to adhere to its provisions or to take proper flight
instruction can have fatal consequences.
Applicability
This manual is applicable for Calidus models from a manufacturing date 01.02.2011 and on.
For earlier models please refer to manual version 1.x which will be maintained in current
status and revised, if necessary.

REVISION LOG
Rev. Inserted by Date Signature

2.0 AutoGyro 01.05.2011
2.1 AutoGyro 01.10.2011

Flight Manual Table of Contents
Calidus List of Effective Pages
CONTENTS
SECTION 1 - GENERAL
1.1 Introduction....................................................................................................1-1
1.2 Certification ...................................................................................................1-1
1.3 Performance Data and Operating Procedures ...............................................1-1
1.4 Definition of Terms ........................................................................................1-2
1.5 Important Note...............................................................................................1-2
1.6 Three-view of the Calidus ..............................................................................1-3
1.7 Description ....................................................................................................1-4
1.8 Technical Data ..............................................................................................1-4
1.9 Rotor .............................................................................................................1-4
1.10 Engine...........................................................................................................1-5
1.11 Propeller........................................................................................................1-5
1.12 Unit Conversion.............................................................................................1-6
1.13 Abbreviations and Terminology .....................................................................1-7
SECTION 2 - LIMITATIONS
2.1 General .........................................................................................................2-1
2.2 Environmental Limitations..............................................................................2-2
2.3 Colour Code for Instrument Markings ............................................................2-2
2.4 Airspeed Limitations and Instrument Markings...............................................2-3
2.5 Rotor Speed Limitations and Instrument Markings.........................................2-3
2.6 Powerplant Limitations and Instrument Markings ...........................................2-4
2.7 Weight and Balance ......................................................................................2-6
2.8 Flight Crew ....................................................................................................2-7
2.9 Kinds of Operation.........................................................................................2-7
2.10 Fuel ...............................................................................................................2-8
2.11 Minimum Equipment......................................................................................2-8
2.12 Placards ........................................................................................................2-9
SECTION 3 - EMERGENCY PROCEDURES
3.1 Engine Failure ...............................................................................................3-1
3.2 Air Restart Procedure ....................................................................................3-2
3.3 Landing into Trees or High Vegetation...........................................................3-2
3.4 Degradation of Engine Power ........................................................................3-2
3.5 Evacuating the Aircraft...................................................................................3-3
3.6 Smoke and Fire .............................................................................................3-3
3.7 Canopy Open in Flight ...................................................................................3-4
3.8 Off-field Landing ............................................................................................3-4
3.9 Flight Control Malfunction ..............................................................................3-4
3.10 Warning Lights ..............................................................................................3-5
3.11 Parameters out of Limits................................................................................3-6
3.12 Additional Cockpit Indications ........................................................................3-6
3.13 Loss of Visibility.............................................................................................3-7
AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Index / LOEP 1

3.14 Recovery System / Rotor System.................................................................. 3-7

3.15 Rotor Icing..................................................................................................... 3-7
3.16 Landing with a Deflated Tyre......................................................................... 3-7
3.17 Failure of Variable Pitch Propeller (if installed) .............................................. 3-8
3.18 Alternative Method of Engine Shut-down....................................................... 3-9
SECTION 4 - NORMAL PROCEDURES
4.1 Airspeeds for Safe Operation ........................................................................ 4-1
4.2 Preparation for Flight..................................................................................... 4-1
4.3 Daily or Pre-flight Checks .............................................................................. 4-1
4.4 Before Boarding ............................................................................................ 4-4
4.5 Before Starting Engine .................................................................................. 4-4
4.6 Starting Engine.............................................................................................. 4-5
4.7 Taxi and Run-up............................................................................................ 4-6
4.8 Take-off Procedure ....................................................................................... 4-6
4.9 Take-off Run ................................................................................................. 4-8
4.10 Climb............................................................................................................. 4-8
4.11 Cruise ........................................................................................................... 4-8
4.12 Descent......................................................................................................... 4-9
4.13 Approach....................................................................................................... 4-9
4.14 Landing ......................................................................................................... 4-9
4.15 Go-around................................................................................................... 4-10
4.16 After Landing............................................................................................... 4-10
4.17 Engine Shut-down....................................................................................... 4-11
4.18 Parking........................................................................................................ 4-11
4.19 Special Procedure: Short Field Take-off ...................................................... 4-11
4.20 Special Procedure: Slow Speed Sink and Recovery.................................... 4-12
4.21 Training Engine In-flight Shut-down and Air Restart .................................... 4-12
4.22 Noise Abatement......................................................................................... 4-12
SECTION 5 - PERFORMANCE
5.1 Demonstrated Operating Temperature .......................................................... 5-1
5.2 Airspeed Calibration...................................................................................... 5-1
5.3 Height-Velocity Diagram................................................................................ 5-2
5.4 Speeds.......................................................................................................... 5-3
5.5 Rate of Climb ................................................................................................ 5-3
5.6 Take-off and Landing Data ............................................................................ 5-3
5.7 Influence on Take-off Distance and Climb Rate............................................. 5-4
5.8 Glide Ratio .................................................................................................... 5-5
5.9 Additional Performance Data......................................................................... 5-6
5.10 Sound Exposure Level / Noise Characteristics .............................................. 5-6
SECTION 6 - WEIGHT AND BALANCE
6.1 General ......................................................................................................... 6-1
6.2 Weight and Balance Record.......................................................................... 6-1
6.3 Compliance with Weight and Balance ........................................................... 6-1

SECTION 7 - SYSTEM DESCRIPTION

7.1 Introduction....................................................................................................7-1
7.2 Airframe and Undercarriage...........................................................................7-1
7.3 Doors, Windows and Exits.............................................................................7-1
7.4 Fuel System ..................................................................................................7-1
7.5 Pneumatic System.........................................................................................7-3
7.6 Power Plant ...................................................................................................7-4
7.7 Propeller........................................................................................................7-4
7.8 Rotor System.................................................................................................7-4
7.9 Vibration Damping .........................................................................................7-5
7.10 Flight Controls ...............................................................................................7-5
7.11 Electrical System ...........................................................................................7-7
7.12 Lighting System.............................................................................................7-7
7.13 Instrument Panel ...........................................................................................7-7
7.14 Intercom ...................................................................................................... 7-12
7.15 Pitot Static ................................................................................................... 7-12
7.16 Indicators and Sensors ................................................................................ 7-12
7.17 Seats and Seatbelts .................................................................................... 7-12
7.18 Stowage Capacity........................................................................................ 7-12
SECTION 8 - HANDLING AND SERVICING
8.1 Maintenance Obligations ...............................................................................8-1
8.2 General .........................................................................................................8-1
8.3 Ground Handling ...........................................................................................8-2
8.4 Cleaning ........................................................................................................8-2
8.5 Refuelling ......................................................................................................8-2
8.6 Checking of Engine Oil Level.........................................................................8-2
8.7 Checking of Engine Coolant Level .................................................................8-3
8.8 Tire Pressure.................................................................................................8-3
8.9 Lubrication and Greasing...............................................................................8-3
8.10 Replenishing of Fluids ...................................................................................8-4
8.11 Engine Air Filter.............................................................................................8-4
8.12 Propeller........................................................................................................8-4
8.13 Battery...........................................................................................................8-4
8.14 Winter Operation ...........................................................................................8-4
8.15 Removal, Disassembly, Assembly and Installation of the Rotor .....................8-5
8.16 Road Transport .............................................................................................8-8
8.17 Repairs..........................................................................................................8-9
SECTION 9 - SUPPLEMENTS
9-1 Variable Pitch Propeller - IVO
9-2 Lights
9-3 GPS/Moving Map Systems
9-4 Fire Indication
9-5 Canopy Indication
SECTION 10 - SAFETY TIPS

APPENDIX
Operator Registration Form
Customer Feedback Form
Incident Reporting Form

LIST OF EFFECTIVE PAGES
Page(s) Rev. Date Page(s) Rev. Date

1-1 to 1-8 2.1 01.10.2011 8-1 to 8-9 2.1 01.10.2011
2-1 to 2-11 2.1 01.10.2011 9-1 - 1 to 3 2.1 01.10.2011
3-1 to 3-9 2.1 01.10.2011 9-2 - 1 2.1 01.10.2011
4-1 to 4-13 2.1 01.10.2011 9-3 - 1 2.1 01.10.2011
5-1 to 5-6 2.1 01.10.2011 9-4 - 1 2.1 01.10.2011
6-1 2.1 01.10.2011 9-5 - 1 2.1 01.10.2011
7-1 to 7-12 2.1 01.10.2011 10-1 to 10-4 2.1 01.10.2011


Flight Manual SECTION 1
Calidus GENERAL
CONTENTS
1.1 Introduction....................................................................................................1-1
1.2 Certification ...................................................................................................1-1
1.3 Performance Data and Operating Procedures ...............................................1-1
1.4 Definition of Terms ........................................................................................1-2
1.5 Important Note...............................................................................................1-2
1.6 Three-view of the Calidus ..............................................................................1-3
1.7 Description ....................................................................................................1-4
1.8 Technical Data ..............................................................................................1-4
1.9 Rotor .............................................................................................................1-4
1.10 Engine...........................................................................................................1-5
1.11 Propeller........................................................................................................1-5
1.12 Unit Conversion.............................................................................................1-6
1.13 Abbreviations and Terminology .....................................................................1-7
AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-i

Calidus GENERAL
AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1 - ii

Calidus GENERAL
SECTION 1 - GENERAL
1.1 Introduction
This manual is designed as an operating guide for pilots, instructors, and owners/operators,
providing information for the safe and efficient operation of this gyroplane. It includes
material required to be furnished to the pilot by the competent certification authority. This
handbook is not designed as a substitute for adequate and competent flight instruction,
however.
Pilots of this aircraft must hold a proper license including the class rating ‘gyroplane’,
corresponding to the aircraft’s registration. A special endorsement may be required to fly
with passengers. It is the pilot’s responsibility to be familiar with this handbook, the special
characteristics of this gyroplane, and all other information and legal requirements relevant
for the operation in his country. The pilot is responsible to determine the gyroplane is safe
for flight, and to operate the aircraft with respect to the procedures and limitations provided
in this manual.
It is the owner’s/operator’s responsibility to have this gyroplane registered and insured,
according to country-specific regulations. The aircraft owner/operator is also responsible for
maintaining the gyroplane in airworthy condition. Maintenance instructions are provided in
the Maintenance Manual and in SECTION 8 of this manual. Note that depending on the
kind of operation, type of maintenance activity, or component involved, the competent
authority may dictate qualified personnel and/or respective facilities.
1.2 Certification
The Calidus is designed, tested and certified according to the German design specifications
for microlight gyroplanes (“Bauvorschriften für Ultraleichte Tragschrauber”, BUT 2001)
including its latest amendment published in “Nachrichten für Luftfahrer” NfL II 13/09 issued
12.02.2009, as well as the British Civil Airworthiness Requirements (BCAR) Section T.
The corresponding certification documents (Geräte-Kennblatt) have been issued by the
responsible Germany department DULV (Deutscher Ultraleichtflugverband e.V.),
respectively the German national certifying authority.
The noise certificate was granted according to the German requirements for noise
protection for microlight gyroplanes (“Lärmschutzverordnung für Ultraleichte
Tragschrauber”).
1.3 Performance Data and Operating Procedures

The legal basis for operating a gyroplane is provided by national law and its respective
regulations. The instructions and conditions contained have to be considered when
operating the gyroplane.
All documented performance data and operating procedures have been identified within the
certification processes for this gyroplane by means of flight test and analysis.
AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-1

Calidus GENERAL
1.4 Definition of Terms

This manual uses WARNINGs, CAUTIONs and NOTEs in bold capital letters to indicate
especially critical and important instructions. Additionally, the colour of the panel (red,
yellow, and grey shading) highlights the significance of the instruction. Definitions for each
term are given below.
WARNING
A warning means that the neglect of the appropriate procedure or condition
could result in personal injury or loss of life.
CAUTION
A caution means that the neglect of the appropriate procedure or condition
could result in damage to or destruction of equipment.
NOTE
A note stresses the attention for a special circumstance, which is essential to
emphasize.
1.5 Important Note

Before each flight pilots must make themselves familiar with the appropriate navigational,
weather and safety information pertinent to their planned route.
The limitations provided in SECTION 2 of this manual must be respected at all times. Check
the manufacturer’s web site www.auto-gyro.com regularly for flight manual updates,
airworthiness directives, service bulletins, or safety information.
Abrupt manoeuvres or flight in heavy turbulence must be avoided as this could lead to rotor
speed variations associated with high stress, possible damage to the aircraft, or
uncontrollable attitudes.

Calidus GENERAL
1.6 Three-view of the Calidus

Calidus GENERAL
1.7 Description
General Characteristics
 Gyroplane with nose gear wheel chassis
 Framework manufactured from inert-gas welded stainless steel tube
 Front aircraft structure is a GRP/CRP monocoque bolted to the airframe
 Two-seat tandem configuration (monocoque design)
 Main landing gear with GRP (glass fibre reinforced plastic) spring spar and hydraulic
disc brakes
 Extruded aluminium rotor
 Rotor head controlled with push-pull control cables
 Rudder controlled with cables
 Rudder and stabilizer surfaces made of GRP (or carbon fibre)
1.8 Technical Data

Length: ...................................................................................................4.78 m
Width: .....................................................................................................1.73 m
Height: ....................................................................................................2.77 m
Empty weight:.......................................................................................262.0 kg
Payload: ...............................................................................................188.0 kg
Take-off weight/mass (max.):................................................................450.0 kg
Fuel tank capacity: .................................................................................... 39 ltr
(with optional auxiliary fuel tank installed) ............................................... 75 ltr
1.9 Rotor
General
Type: ........................2-bladed, fixed pitch, free to teeter, with orange end caps
Material: ............................................... EN AW 6005A T6 aluminium extrusion
Blade profile: ................................................................................. NACA 8H12
Rotor diameter.......................................................................................... 8.4 m
Rotor disc area ....................................................................................55.4 sqm
Rotor disc load ................................................................................. 8.1 kg/sqm

Calidus GENERAL
1.10 Engine
ROTAX 912 ULS
 4-cylinder, four-stroke spark-ignition engine with opposed cylinders
 Liquid cooled cylinder heads
 Air cooled cylinders
 Dry sump forced lubrication with separate oil tank
 Automatic adjustment by hydraulic valve tappet
 2 carburettors
 Mechanical fuel pump
 Electronic dual ignition
 Propeller speed reduction unit, engine mount assembly
 Electric starter (12V 0,6kW)
 Air intake system, exhaust system
ROTAX 914 UL
 4-cylinder, four-stroke spark-ignition engine with opposed cylinders with turbo charger
 Air cooled cylinders
 Dry sump forced lubrication with separate oil tank
 Automatic adjustment by hydraulic valve tappet
 2 carburettors
 Electronic dual ignition
 Propeller speed reduction unit, engine mount assembly
 Electric starter (12V 0,6kW)
 Air intake system, exhaust system
1.11 Propeller
HTC 3 Blade
Airscrew with ground adjustable pitch made of CRP / GRP
Model .........................................................................HTC 3 Blade 172 ccw 3B
Number of blades ............................................................................................ 3
Diameter ............................................................................................... 172 cm
In-flight pitch adjustment ........................................................................... none
IVO Prop
Airscrew with in-flight adjustable pitch made of CRP / GRP
Model ........................................................................IVO Prop medium ccw 3B
Number of blades ............................................................................................ 3
Diameter ............................................................................................... 172 cm
In-flight pitch adjustment .................................... electric, continuous adjustable

Calidus GENERAL
1.12 Unit Conversion
Multiply by to obtain
kts (knots) 1.852 km/h
km/h (kilometres per hour) 0.54 kts
mph (miles per hour) 1.61 km/h
km/h (kilometres per hour) 0.62 mph
ft (feet) 0.305 m
m (metres) 3.28 ft

Calidus GENERAL
1.13 Abbreviations and Terminology
ACL Anti-Collision Light

AGL Above Ground Level
ATC Air Traffic Control
CAS Calibrated AirSpeed – indicated speed corrected for installation errors
ccw Counter Clock Wise
CG Centre of Gravity
CHT Cylinder Head Temperature
CRP Carbon Reinforced Plastic
CSP Constant Speed Propeller
DA Density Altitude
DULV Deutscher UltraLeichtflugVerband e.V.
Empty Wt Empty Weight of the gyroplane including oil, cooling liquid and unusable fuel
FOM Flight and Operation Manual
G/g G-loading as a factor of gravity
GEN Generator
GPS Global Positioning System
GRP Glass Reinforced Plastic
H/V Height-Velocity
IAS Indicated AirSpeed – airspeed values in this manual refer to indicated air speed
ICAO International Civil Aviation Organization
In Hg (Manifold) Pressure, corresponding to inch mercury
ISA International Standard Atmosphere
JNP JahresNachPrüfung – Annual Inspection
LED Light Emitting Diode
LH Left-Hand
LOEP List Of Effective Pages
ltr Litre
MAP Manifold Absolute Pressure
MCP Maximum Continuous Power
MTOW Maximum Take-Off Weight (mass)
OAT Outside Air Temperature
PA Pressure Altitude
RBT Rotor Bearing Temperature
RH Right-Hand
ROZ Research OktanZahl– means: Octane Number
RPM Revolutions Per Minute
sqm Square metres
TAS True AirSpeed – calibrated airspeed corrected for air density
TCU Turbo Control Unit (engine)

Calidus GENERAL
TOC Table Of Contents

TOP Take-Off Power
VB Design speed for maximum gust intensity
VFR Visual Flight Rules
VH Maximum level-flight speed at maximum continuous power
VHmin Minimum level-flight speed
VNE Never-Exceed Speed – maximum speed that must never be exceeded
VOX Voice Operated eXchange, means: voice activation (level)
VPP Variable Pitch Propeller
VSI Vertical Speed Indicator
VX Speed for best angle of climb
VY Speed for best rate of climb and maximum endurance
W&B Weight and Balance

Calidus LIMITATIONS
CONTENTS
2.1 General .........................................................................................................2-1

2.2 Environmental Limitations..............................................................................2-2
2.3 Colour Code for Instrument Markings ............................................................2-2
2.4 Airspeed Limitations and Instrument Markings...............................................2-3
2.5 Rotor Speed Limitations and Instrument Markings.........................................2-3
2.6 Powerplant Limitations and Instrument Markings ...........................................2-4
2.7 Weight and Balance ......................................................................................2-6
2.7.1 Weight Limits ............................................................................................2-6
2.7.2 Centre of Gravity (CG) Limits....................................................................2-6
2.7.3 Demonstrated Structural Load Factors......................................................2-6
2.8 Flight Crew ....................................................................................................2-7
2.9 Kinds of Operation.........................................................................................2-7
2.10 Fuel ...............................................................................................................2-8
2.10.1 Approved Fuel Grades.........................................................................2-8
2.10.2 Fuel Tank Capacities ...........................................................................2-8
2.10.3 Unusable Fuel......................................................................................2-8
2.11 Minimum Equipment......................................................................................2-8
2.12 Placards ........................................................................................................2-9

Calidus LIMITATIONS

Calidus LIMITATIONS
SECTION 2 - LIMITATIONS
This section contains operating limitations, instrument markings and basic placards which
are required for safe operation of the gyroplane, including its engine, and standard
equipment or systems.
2.1 General
WARNING
The operation of a gyroplane demands professional pilot instruction and
dedicated training on gyroplanes. Without a valid license the gyroplane must
not be operated.
WARNING
During the entire flight adequate rotor loading must be maintained. Do not
perform any manoeuvres resulting in the sensation of feeling light or near
weightless.
WARNING
Smoking on board is prohibited!
CAUTION
This gyroplane has been designed and tested for a safe design load of 3g at
maximum gross mass. Note that flying at higher speeds in turbulent air,
especially in combination with aggressive manoeuvres or a steep turn, can
easily create higher loads on the aircraft.
NOTE
This gyroplane does not comply with the terms of the international authority for
civil aviation (ICAO). Therefore, it is not possible to operate it in international
air traffic unless specific intergovernmental agreements allow doing so. The
reason for this is that there is no international common basis for gyroplanes.

Calidus LIMITATIONS
NOTE
During the certification process all required safe loads have been successfully
demonstrated. However, the gyroplane may be exposed to much higher loads
especially when operated on rough surfaces, such as an unprepared grass
strip. In this case it is even more essential to perform a thorough pre-flight
inspection and have components and parts exchanged, where needed.
2.2 Environmental Limitations

Maximum wind speed or gust intensity ..................................................... 40 kts
Maximum crosswind component for take-off and landing.......................... 20 kts
Maximum tailwind component for take-off and landing................................5 kts
Temperature................................................................................- 20 to + 40 °C
WARNING
Do not consider flying in the likelihood of severe weather. Thunderstorms may
develop rapidly with the risk of heavy precipitation or hail, severe turbulence
with strong vertical air movements, and lightning strike. If, despite proper flight
planning, a thunderstorm should be encountered, consider a precautionary
landing to avoid the squall line. A lightning strike may damage the main rotor
bearing. Thorough inspection and maintenance after lightning strike must be
performed.
2.3 Colour Code for Instrument Markings
Red Operating limits. Pointer should not enter red during normal operation
Yellow Precautionary or special operating procedure range
Green Normal operating range

Calidus LIMITATIONS
2.4 Airspeed Limitations and Instrument Markings
Air Speed Marking
VNE Never Exceed Speed Red radial 185 km/h
Yellow arc 130 – 185 km/h
VB Design speed for max. gust intensity Green arc 30 - 130 km/h
Yellow arc 0 – 30 km/h
WARNING
The maximum speed V NE must never be exceeded! Do not exceed V B when
flying through turbulence, gusts or rough winds!
2.5 Rotor Speed Limitations and Instrument Markings
Rotor Speed Marking
Rotor speed limit Red radial 610 RPM
Rotor speed caution range Yellow arc 550 – 610 RPM
Continuous rotor speed Green arc 200 – 550 RPM
Maximum pre-rotation speed Yellow radial 240 RPM

Calidus LIMITATIONS
2.6 Powerplant Limitations and Instrument Markings
Engine Speed Marking
Maximum engine speed Red radial 5800 RPM
5 minute take-off power regime Yellow arc 5500 – 5800 RPM
Maximum continuous power Green arc 1400 – 5500 RPM
Recommended pre-rotation clutch speed Green radial 1800 RPM
Yellow arc 0 – 1400 RPM
Engine Oil Temperature Marking
Maximum oil temperature Red radial 130 °C
Yellow arc 110 – 130 °C
Maximum continuous oil temperature Green arc 90 – 110 °C
Yellow arc 50 – 90 °C
Minimum oil temperature Red radial 50 °C
Cylinder Head Temperature Marking
Maximum cylinder head temperature Red radial 135 °C
Green arc 50 – 135 °C
Engine Oil Pressure Marking
Maximum oil pressure Red radial 7 bar
Yellow arc 5 – 7 bar
Maximum continuous oil pressure Green arc 2 – 5 bar
Yellow arc 0.8 – 2 bar
Minimum oil pressure Red radial 0.8 bar

Calidus LIMITATIONS
Manifold Pressure* ROTAX 912 ULS Marking
Maximum manifold pressure Red radial 31 In Hg
Yellow arc 27 – 31 In Hg
Maximum continuous MAP Green arc 0 - 27 In Hg
Manifold Pressure* ROTAX 914 UL Marking
Maximum manifold pressure Red radial 39 In Hg
Yellow arc 31 – 39 In Hg
Maximum continuous MAP Green arc 0 - 31 In Hg
* Applicable only if installed, MAP gauge is optional equipment and recommended in conjunction
with an adjustable pitch propeller. MAP limits do not apply at engine speeds above 5100 RPM,
marked by a yellow triangle at the RPM gauge / engine speed indicator.

Calidus LIMITATIONS
2.7 Weight and Balance

2.7.1 Weight Limits
Maximum take-off weight (MTOW): .........................................................450 kg
CAUTION
The take-off weight is the total weight of the gyroplane including empty weight,
optional/additional equipment, occupants, fuel, and luggage at take-off. The
maximum value specified above must never be exceeded.
Maximum weight in front seat (incl. compartment below seat): ................125 kg

Minimum weight in front seat (incl. compartment below seat): ...................65 kg
Maximum weight in aft seat (incl. compartment below seat): ...................125 kg
NOTE
Pilots in the front seat weighing less than 65 kg must carry corresponding
ballast.
Storage compartments below front and aft seat

Maximum weight in each storage compartment (4 ea.) .............................2.5 kg
NOTE
When loaded, the weight in each storage compartment has to be deducted from
the maximum weight in the respective seat.
2.7.2 Centre of Gravity (CG) Limits
The centre of gravity is considered to be within limits if all weight limits above are respected.
For details see SECTION 6 of this manual.
2.7.3 Demonstrated Structural Load Factors
Demonstrated positive load factor (500 kg)................................................ + 3 g

Demonstrated negative load factor (500 kg) – structural limit...................... - 1 g
Important note: the indication of a demonstrated negative load factor represents a

structural limit only. In flight, the limitations (see 2.9) have to be respected at all times.

Calidus LIMITATIONS
2.8 Flight Crew
Minimum crew is one pilot in the front seat.
Harness in aft seat must be fastened and tight.
The aft control stick must be removed unless the passenger seat is occupied by a qualified
flight instructor.
2.9 Kinds of Operation
Only day VFR operation is approved!
Aerobatic flight is prohibited!
NOTE
Manoeuvres involving bank angles of more than 60° are considered to be
aerobatic flight.
Low-G manoeuvres are prohibited!
WARNING
Any maneuver resulting in a low-G (near weightless) condition can result in a
catastrophic loss of lateral/roll control in conjunction with rapid main rotor
RPM decrease. Always maintain adequate load on the rotor and avoid
aggressive forward control input performed from level flight or following a pull-
up.
Excessive side-slip is prohibited!
WARNING
Side slip may be performed only with proper training and within safe
boundaries. Use gentle pedal input for initiation and stabilization. Do not rely
on airspeed indication in side slip. Never perform abrupt control stick input into
the direction of motion. Be aware that excessive side slip may result in an
uncontrollable and unrecoverable (low-G) attitude.

Calidus LIMITATIONS
Flight in icing conditions is prohibited!
NOTE
Icing may occur even at temperatures above freezing!
Operation in strong gusts or wind speeds of more than 72 km/h (40 kts) is prohibited!
2.10 Fuel
2.10.1 Approved Fuel Grades
Preferred fuel
EN 228 Super or EN228 Super plus (min. ROZ 95)
Alternate fuel
AVGAS 100 LL (ASTM D910)
For operational constraints and maintenance aspects when using preferred fuel and
alternate fuel, refer to the engine manufacturer’s manual.
2.10.2 Fuel Tank Capacities
Maximum tank capacity, standard tank ...................................................... 39 ltr

Maximum tank capacity, with optional auxiliary fuel tank............................ 75 ltr
2.10.3 Unusable Fuel
Unusable fuel quantity, standard tank ....................................................... 0.6 ltr

Unusable fuel quantity, with optional auxiliary fuel tank............................. 1.2 ltr
2.11 Minimum Equipment

The following equipment must be operative for flight:
 Air speed indicator
 Altimeter
 Compass
 Rotor RPM indicator
 Engine instruments (oil pressure, RPM, CHT)
 Pre-rotator

Calidus LIMITATIONS
2.12 Placards
In clear view of the pilot:
Only VFR day is approved

Aerobatic flight prohibited!
Low-G manoeuvres prohibited!
Flight in icing conditions prohibited!
For additional limitations see Flight Manual!
Max. gross weight: ________

Empty weight: ________
Max. useful load: ________
At front seat:
Max. weight in seat: 125 kg

Min. weight in seat: 65 kg
At aft seat:
Max. weight in seat: 125 kg
Solo from front seat only
Occupant warning (front and aft seat):
OCCUPANT WARNING
This aircraft has not been certified to an
international requirement

Calidus LIMITATIONS
At each storage compartment below seats:
Max. load: 2.5 kg

W&B must be respected!
At fuel filler neck:
Min. ROZ 95
AVGAS 100LL
At fuel filler neck:
Capacity Std. Tank 39 litres

With Aux. Fuel Tank 75 litres
At oil filler neck:
Engine Oil: ______________

Approved oil types see engine manual!
At throttle quadrant

Calidus LIMITATIONS
At fuel shut-off valve:
At canopy locking lever:
Inside Outside
At both static ports (2x):
Static Port
Do not obstruct!

Calidus LIMITATIONS

Calidus EMERGENCY PROCEDURES
CONTENTS
3.1 Engine Failure ...............................................................................................3-1

3.2 Air Restart Procedure ....................................................................................3-2
3.3 Landing into Trees or High Vegetation...........................................................3-2
3.4 Degradation of Engine Power ........................................................................3-2
3.5 Evacuating the Aircraft...................................................................................3-3
3.6 Smoke and Fire .............................................................................................3-3
3.7 Canopy Open in Flight ...................................................................................3-4
3.8 Off-field Landing ............................................................................................3-4
3.9 Flight Control Malfunction ..............................................................................3-4
3.9.1 Engine Power Control / Throttle ................................................................3-4
3.9.2 Rudder Malfunction...................................................................................3-5
3.9.3 Rotor Head Control...................................................................................3-5
3.10 Warning Lights ..............................................................................................3-5
3.10.1 GEN or Low Volt Indicator Light ...........................................................3-5
3.10.2 Low Volt...............................................................................................3-5
3.10.3 BOOST WARN Light (red) - only ROTAX 914 UL ................................3-5
3.10.4 BOOST CAUTION Light (orange) - only ROTAX 914 UL .....................3-6
3.10.5 Fan ......................................................................................................3-6
3.11 Parameters out of Limits................................................................................3-6
3.12 Additional Cockpit Indications ........................................................................3-6
3.12.1 Fire Indication (if installed) ...................................................................3-6
3.12.2 Canopy Indication (if installed) .............................................................3-6
3.13 Loss of Visibility.............................................................................................3-7
3.14 Recovery System / Rotor System ..................................................................3-7
3.15 Rotor Icing.....................................................................................................3-7
3.16 Landing with a Deflated Tyre .........................................................................3-7
3.17 Failure of Variable Pitch Propeller (if installed)...............................................3-8
3.18 Alternative Method of Engine Shut-down .......................................................3-9


SECTION 3 - EMERGENCY PROCEDURES

This chapter contains the check lists and procedures to be executed in emergency
situations.
Emergencies due to defects of the gyroplane or its engine are extremely seldom if the
aircraft is checked thoroughly before each flight and continuously maintained. If there
should occur a case of emergency anyhow, the guidelines of this chapter are to be followed
in order to manage the emergency.
This gyroplane, like most recreational air vehicles, is fitted with a non-certified engine. This
means that there may be a higher risk of engine failure than with a certified aircraft engine,
with the associated risks of damage or injury as the result of an unplanned landing.
Therefore strict compliance with the engine manufacturer’s maintenance schedules,
operational procedures and any additional instructions is essential. The aircraft must always
be flown with the risk of engine failure in mind, and must not be flown over any areas where
a forced landing cannot be safely executed.
3.1 Engine Failure

In case of an engine failure the following action is recommended:
Engine failure during take-off run

 Maintain directional control using sensitive but appropriate pedal input
 With the rotor/stick remaining aft, let gyroplane decelerate. Wheel brakes may be
used to assist
 At walking speed level-off rotor disc, use wheel brakes and bring rotor to a stop
Engine failure after lift-off and below 150 ft AGL

 The climb-out should be performed according to the Height-Velocity-Diagram
in CHAPTER 5
 When engine failure occurs, immediately lower nose to enter glide attitude
 Continue straight ahead – a 180 turn back to the airfield may be a bad option
 Maintain airspeed until ground is approached, then perform flare
 Depending on final approach speed be prepared to flare more distinctly than normal
Engine failure at or above 150 ft AGL

 Consider wind speed and direction
 Select a suitable landing site
 If time allows, a restart may be attempted, see “Air restart procedure” below
 Perform a landing into wind and/or upslope if possible
 Prior to touch-down switch OFF Main Switch
WARNING
Always plan your route to remain within safe gliding distance to areas where a
safe forced landing can be performed in case of an engine failure. A landing in
high trees or open waters may end fatally.

NOTE
The best engine-off glide ratio is about 1:3 at 90 km/h. Depending on a possible
headwind the glide may be extended by slightly increasing airspeed. It is
heavily recommended to train your forced landing capabilities regularly,
preferably with a qualified flight instructor.
3.2 Air Restart Procedure

 Check fuel valve OPEN
 Check fuel pump(s) ON
 Check both magnetos ON
 Throttle slightly open
 With the left hand, turn the Main Switch/Starter key completely to OFF, then START
 If possible, allow engine and oil to warm-up before full power is applied
NOTE
The starter interlock function prevents inadvertent starter engagement. Before
attempting an engine start, the interlock must be reset by turning the Main
Switch/Starter key to OFF.
3.3 Landing into Trees or High Vegetation

 Assume the surface of the treetops or vegetation as level
 Plan touch-down and flare with minimum ground speed and minimum rate of descent
 As soon as the wheels contact the vegetation bring the rotor disc to level attitude to
avoid partial blade tip contact with vegetation
 Shut down engine by switching magnetos OFF and master switch OFF
3.4 Degradation of Engine Power

A gradual decay in engine RPM, accompanied by a rough running engine or even vibration
may be an indicator for carburettor icing. In this case, continue with a high power setting
and change altitude into air which is less susceptible to carburettor icing.
If the situation cannot be corrected be prepared for further loss of power and ultimately
engine failure.

NOTE
The phenomenon of carburettor icing is extremely unlikely with this engine
type as it is fitted with a hot water heated jacket around the carburettor inlets.
Note that the system can work properly only when the engine is at operating
temperature.
3.5 Evacuating the Aircraft

In normal circumstances occupants should never leave the aircraft while the propeller or the
rotors are turning. If abandoning the aircraft in an emergency the pilot should turn off the
engine magneto switches and turn the master switch to “OFF” if this can be done without
endangering the occupants.
If abandoning the aircraft with either the propeller and/or the rotors turning the occupants
should follow a path in line with the nose of the aircraft, to minimise the risk of being struck
by either the rotor or the propeller.
Occupants should be briefed before flight on emergency evacuation procedures, including:
Actions to be taken in the event of a forced landing
Operation of the seat harness
REMOVED: Disconnection of any intercom leads or other connections to the aircraft
How to open the doors, or to break the windshield if required (using the emergency
hammer to break the Plexiglas)
How to safely exit and move away from the aircraft
3.6 Smoke and Fire

Indications of smoke should be treated in the same way as a fire. In case of fire the
following action is recommended:
Smoke or fire on ground

 Both magnetos OFF and master switch OFF to shut-down engine and fuel pumps
 Evacuate aircraft
 Close fuel shut-off valve if situation allows
 Extinguish fire and have damage inspected
Fire in flight
 Immediately switch off cabin heat (if installed – push heat control)
 Open ventilation for fresh air
 Initiate an emergency landing
 Initiate emergency call, if time and situation permits
 As soon as a power-off landing can be assured, shut down engine by switching
magnetos OFF and master switch OFF
 Continue procedure as described in “Engine Failure” and “Smoke or fire on ground”

3.7 Canopy Open in Flight

If the canopy pops open in flight, immediately initiate a left side-slip (i.e. right pedal) so that
the oncoming air maintains the canopy shut. Reduce air speed and lock the canopy. If
impossible to lock, land immediately at the nearest suitable location. Approach with the
nose pointed to the right (left side slip) and align just prior to touch-down.
3.8 Off-field Landing

A precautionary landing at a non-prepared site may be performed at pilot’s discretion in
order to avoid unexpected weather, in case of severe illness of the pilot or a passenger, or if
technical defects are suspected, for example sudden and severe rotor vibrations.
 Select a suitable landing site from safe altitude, considering slope, wind speed and
direction
 Fly a reconnaissance pattern to check for obstacles, especially power lines, wires,
and cables in the approach and go-around path
 Overfly the landing site to check for obstructions such as fences, ditches, rocks,
height of vegetation, and select most suitable touch-down zone
 Perform a normal approach and touch-down into wind with minimal ground speed
3.9 Flight Control Malfunction

In case of a flight control failure the gyroplane can be controlled with the remaining primary
and secondary controls, including power and trim. An immediate reduction of power,
respectively speed may be necessary to avoid pitch oscillations (phugoid) or other effects
affecting dynamic or static stability. Navigate to a suitable landing site with wide and shallow
turns and approach against the wind.
3.9.1 Engine Power Control / Throttle
Throttle jammed open or max

Navigate to a suitable landing site with the power set. If over safe terrain, magneto switches
may be used to control power. When within gliding distance to the selected landing site,
shut-down engine to perform a power-off landing as per Emergency Procedure “Engine
failure”.
NOTE
In case of a control cable breakage the carburettor will be automatically set to
full throttle position.
Throttle jammed closed

Land as per Emergency Procedure “Engine failure”. Residual power may be used to extend
the glide.

3.9.2 Rudder Malfunction
In case of a stuck or loose rudder, continue flight to a suitable, preferably wide landing site
that allows a landing into the wind. If necessary reduce power to avoid excessive side slip.
Align gyroplane prior to touch-down, using engine torque or lateral control input to the side
where the nose is pointed.
3.9.3 Rotor Head Control
In case of a rotor head control malfunction, control pitch attitude using careful trim input and
power setting. Use rudder for directional control and for shallow turns. In some conditions it
may be appropriate to reduce power/speed in order to avoid phugoid effects or a possible
negative yaw-roll coupling. Approach landing site with wide and shallow turns.
3.10 Warning Lights

3.10.1 GEN or Low Volt Indicator Light
ROTAX 912 ULS: If any of the indicators are permanently lit, switch off
all unnecessary electrical consumers and land at the nearest airfield
where maintenance can be performed.
ROTAX 914 UL: If any of the indicators are permanently lit, switch off all
unnecessary electrical consumers and perform a precautionary landing
within 15 minutes. Be prepared for an engine failure.
NOTE
A pulsed GEN indicator light is normal and indicates proper function of the
generator.
3.10.2 Low Volt
Battery voltage of the system has dropped below a safe value. Refer to chapter above.
Aircraft lights and the 12V power receptacle will be disabled automatically.
3.10.3 BOOST WARN Light (red) - only ROTAX 914 UL
Continuously lit
If continuously lit, the maximum admissible boost pressure was exceeded. Reduce power
into normal operating range and consider restricted engine performance or boost control
malfunction. Record duration and have maintenance action performed.
Blinking
When blinking, the allowable 5 minutes take-off power time limit has been exceeded.
Reduce power into continuous range. Record duration and have maintenance action
performed.

3.10.4 BOOST CAUTION Light (orange) - only ROTAX 914 UL
A blinking BOOST CAUTION light indicates a problem with the turbo/boost control, its
sensors or the servo. Engine power is degraded and continuous operation may lead to
engine damage. Perform a precautionary landing considering reduced engine performance
and be prepared for engine failure.
3.10.5 Fan
The engine mounted electrical blower fan is active. Monitor engine instruments and mind
higher electrical power consumption. If possible, reduce engine power and increase speed.
3.11 Parameters out of Limits
PARAMETER EXCURSION CORRECTIVE ACTION
Engine Oil Upper limit or Reduce power and increase air speed. If condition
Temperature yellow arc cannot be corrected, land as soon as practicable.
Lower limit Allow engine to warm-up on ground.
Within lower Increase power setting, if possible. If condition prevails
yellow arc in normal flight, have maintenance action performed.
Cyl. Head Upper limit Reduce power and increase air speed. If condition
Temperature cannot be corrected, land as soon as practicable.
Engine Oil Upper limit or Reduce power. If condition cannot be corrected, have
Pressure yellow arc maintenance action performed prior to next flight.
Lower limit If combined with other indications, such as rising oil
temperature or unusual engine behaviour, shut-down
engine and perform a power-off landing as per
Emergency Procedure “Engine failure”.
Otherwise, monitor engine instruments carefully and
land as soon as practicable. Have maintenance action
performed.
3.12 Additional Cockpit Indications

3.12.1 Fire Indication (if installed)
Refer to emergency procedure “Smoke and Fire” and Flight Manual Supplement.
3.12.2 Canopy Indication (if installed)
Refer to emergency procedure “Canopy Open in Flight” and Flight Manual Supplement.

3.13 Loss of Visibility

In case of canopy misting, open air vents and windows to ensure proper ventilation. If the
situation cannot be corrected or occurs suddenly, such as after a bird strike or canopy icing,
maintain safe attitude by visual reference to the sides, using the open sliding window, if
necessary.
When at safe height, stabilize the aircraft at 90 km/h and clear the viewing obstruction by
using a hand through the sliding window.
If forward vision is still impaired or lost, continue flight with a left side slip, using the open
sliding window for visual reference. Land at the nearest suitable location and align just prior
to touch-down.
3.14 Recovery System / Rotor System

This gyroplane is not equipped with a ballistic recovery system. However, its rotor system
which is in permanent autorotation serves as such a system. Therefore, the entire rotor
system including its rotor head with blade attachments and the corresponding components
of the flight controls have to be inspected and maintained carefully.
If any undue vibration or unusual behaviour is experienced a precautionary landing should
be considered.
3.15 Rotor Icing

A more than normal or constantly increasing power demand may be caused by an iced-up
rotor system. This could ultimately result in a condition where altitude cannot be maintained,
even at maximum power. An iced-up rotor system can also cause severe vibration. If any of
the signs for rotor icing is evident, carry out a precautionary landing.
3.16 Landing with a Deflated Tyre

Plan to land directly into the wind with minimum rate of descent at touch-down, if possible
on a grass runway. Maintain directional control with adequate pedal input. Consider the use
of some propeller thrust to increase rudder effectivity. Lower nose gently with the nose
wheel pointing straight.
Alternatively, if landing on asphalt is unavoidable, approach normally, with the intent of a
zero-speed touch-down directly into wind.
Only if impossible to recover the aircraft from the landing area should it be manoeuvred
under its own power, as this could further damage the tire and wheel rim.

3.17 Failure of Variable Pitch Propeller (if installed)

Noticeable defect:
In case of a noticeable mechanical defect, indicated by sudden vibration or noise, perform a
precautionary landing.
Run-away:
Propeller pitch changes without command, usually resulting in unexpected or sudden
change in engine RPM and engine manifold pressure.
Run-away to FINE: RPM will increase and propeller pitch will stop in full
FINE position. Reduce power if needed, to stay within RPM limits.
Run-away to COARSE: RPM will decrease and MAP will rise until
propeller pitch stops in full COARSE position. Reduce power if needed,
to stay within MAP limits.
In both cases do not try to re-engage circuit breaker until the cause of the run-away has
been determined. Continue according to emergency procedure ‘FREEZE’.
Freeze:
Propeller pitch does not react to pilot input, engine RPM does not change while propeller
pitch control is activated. Proceed according to the following table:
Before take off Do not take-off

During take-off and climb Try to keep climbing to a safe altitude,
return to the airfield and land. If the aircraft
does not climb, maintain altitude and to
return in a flat curve.
During cruise flight Depending on the prop position, it should
be possible to find a speed and RPM to
continue the flight to the next possible
landing area. Depending on the prop
position your descent will look different
and a go around is probably not possible.
During descent Depending on the prop position (in case of
cruise), your descent will look different and
a go around will probably not be possible.
During landing Continue approach as planned. If the prop
changes to cruise and the landing looks
too long, keep in mind to cut the engine.

3.18 Alternative Method of Engine Shut-down

If the engine continues running after the magnetos have been switched off use one of the
following alternative methods:
Hold throttle lever in IDLE position firmly while overstretching the cable ends of the
carburettor control cables with the other hand.
Alternatively
Engage full choke, wait a few seconds and open the throttle suddenly. This normally chokes
the engine and causes it to stop
Alternatively – only ROTAX 914
Turn master switch to off to deactivate both primary and secondary electrical fuel pump. The
engine will starve after approximately 30 – 60 seconds.


Calidus NORMAL PROCEDURES
CONTENTS
4.1 Airspeeds for Safe Operation.........................................................................4-1

4.2 Preparation for Flight .....................................................................................4-1
4.3 Daily or Pre-flight Checks ..............................................................................4-1
4.4 Before Boarding ............................................................................................4-4
4.5 Before Starting Engine...................................................................................4-4
4.6 Starting Engine..............................................................................................4-5
4.7 Taxi and Run-up ............................................................................................4-6
4.8 Take-off Procedure........................................................................................4-6
4.9 Take-off Run..................................................................................................4-8
4.10 Climb.............................................................................................................4-8
4.11 Cruise............................................................................................................4-8
4.12 Descent .........................................................................................................4-9
4.13 Approach.......................................................................................................4-9
4.14 Landing .........................................................................................................4-9
4.15 Go-around ................................................................................................... 4-10
4.16 After Landing ............................................................................................... 4-10
4.17 Engine Shut-down ....................................................................................... 4-11
4.18 Parking........................................................................................................ 4-11
4.19 Special Procedure: Short Field Take-off ...................................................... 4-11
4.20 Special Procedure: Slow Speed Sink and Recovery .................................... 4-12
4.21 Training Engine In-flight Shut-down and Air Restart..................................... 4-12
4.22 Noise Abatement ......................................................................................... 4-12


SECTION 4 - NORMAL PROCEDURES

This section contains check list items, instructions and procedures for the operation of the
gyroplane. However, these procedures do not replace the pilot’s appreciation of the
individual situation.
4.1 Airspeeds for Safe Operation

Climb ............................................................................................ 100 km/h IAS
Best rate of climb / best endurance .................................................90 km/h IAS
Best range .................................................................................... 130 km/h IAS
Approach ...................................................................................... 100 km/h IAS
4.2 Preparation for Flight

The pilot shall be familiar with the aircraft limitations detailed in SECTION 2 of this manual
and shall have performed proper flight planning considering required legal aspects, as well
as SECTION 5 ‘PERFORMANCE’ and SECTION 6 ‘WEIGHT AND BALANCE’ of this
manual. The use of check lists as provided in this manual is mandatory for a safe operation.
4.3 Daily or Pre-flight Checks

All daily or pre-flight check list items consist of visual checks and do not replace
professional mechanical inspection and maintenance. The following check list applies for
the standard Calidus gyroplane.
Note that depending on optional equipment installed the necessary checks may include
additional items according to the flight manual supplement provided with the optional
equipment. It is advisable for the owner/operator to compile his own check list suitable to his
particular configuration.
The pre-flight check is structured into 11 stations which are organized as a clock-wise walk-
around to provide a logical flow and sequential order, thus minimizing the risk of left-over or
overlooked items.

The following checks must be carried out before each flight. However, if the gyroplane is
operated by a single pilot or within an organization where the checks are performed by or
under the supervision of qualified personnel, check list items marked with a preceding ‘ʘ’
may be carried out daily, before the first flight of the day.
Before exterior check

ʘ Fuel tank drain(s)................................................................................... Sample
ʘ Snow/ ice (if any) ................................................................................ Removed
Documents ............................................................................... Check complete
Exterior check
Station 1 (forward fuselage and canopy)
General appearance..................................................................................... OK
Pitot cover (if installed) ....................................................................... Removed
Rotor lash bag (if sufficient brake pressure)........................................ Removed
Canopy condition and cleanliness........................................... Check, no cracks
ʘ Nose wheel condition and air pressure .................................................... Check
Station 2 (pilot station, RH side)

MAG switches ................................................................................. Check OFF
Rotor brake pressure..........................................................................min. 6 bar
ʘ Throttle lever .............................................................. Check function, full travel
ʘ Brake lever and lock ............................................. Check function and condition
ʘ Brake fluid level ....................................................................................... Check
ʘ Pedals and control linkage ....................................................................... Check
ʘ Forward control stick bolts and nuts ...................................................... Secured
ʘ Monocoque structure condition ................................................................ Check
Loose objects ........................................................................Removed/secured
Station 3 (passenger station, RH side)

Aft seat belts......................................................................... Fastened and tight
Aft control stick ................................................................................... Removed
If installed: free travel, no contact with back rest .................... Checked/adjusted
ʘ Monocoque structure condition ................................................................ Check
Loose objects ........................................................................Removed/secured

Station 4 (main gear spring spar, RH)

RH Main wheel running surface ............................................................... Check
Air pressure and slip mark ............................................................. Visual check
ʘ Brake and wheel attachment .................................................................... Check
Wheel pant and attachment ..................................................................... Check
ʘ Main gear spring spar attachment ............................................................ Check
Main gear spring spar ........................................................................ No cracks
Lower rotor flight control attachments ................. No excessive play and secure
Cooling air intake .......................................................................No obstructions
Vibration decoupling element ........................................... Bolts tight and secure
Cardanic hinge bolts (2x) .................................................... Cotter pins installed
Upper rotor flight control attachments ................. No excessive play and secure
ʘ Main rotor bearing ..................................................................... Check condition
ʘ Pre-rotator assembly and brake ................................................ Check condition
ʘ Teeter bolt (bolt end)........................................................................ Free to turn
Teeter bolt (nut end) ............................................................. Cotter pin installed
ʘ Teeter stops ............................................................................................. Check
ʘ Rotor hub and blade clamping area ......................................................... Check
Blade attachment bolts................................................ All installed and fastened
ʘ Inner blade caps ........................................................................................ Tight
Station 5 (engine, RH side)

Open RH access door
ʘ Before turning prop: MAG switches .................................................. Check OFF
ʘ Engine oil level......................................................................................... Check
ʘ Dip stick and oil cap .............................................................. Installed & Secure
ʘ Coolant level ............................................................................................ Check
Close RH access door
Oil cooler and hoses RH ........................................ Clean, no leaks, fittings tight
Exhaust system RH ........................................................................... No cracks
Engine cowling RH.................................. Properly installed, all fasteners locked
Station 6 (stabilizer)
ʘ Stabilizer general condition ...................................................................... Check
Stabilizer attachment ............................................................................... Check
Rudder control cable linkage.................................................................... Check
Upper rudder bearing................................................ Secure, no excessive play
Rotor blades condition and cleanliness .................................................... Check
Blade tips................................................................................................... Tight
Station 7 (keel tube and propeller)

ʘ Keel tube suspension pad .................................................... No excessive wear
Propeller condition and cleanliness .......................................................... Check
Propeller leading edge and tips........................................................No damage
Spinner (if installed) .................................................................. Tight, no cracks
Variable pitch propeller (if installed): brushes ........................................... Check
Variable pitch propeller (if installed): tension strips................................... Check

Station 8 (engine, LH side)

ʘ Main frame rear side / welded joints.......................... No cracks, no deformation
Oil cooler and hoses LH ........................................ Clean, no leaks, fittings tight
Exhaust system LH.............................................................................No cracks
Engine cowling LH.................................. Properly installed, all fasteners locked
Station 9 (main gear spring spar, LH)

LH Main wheel running surface................................................................ Check
Air pressure and slip mark ..............................................................Visual check
ʘ Brake and wheel attachment ................................................................... Check
Wheel pant and attachment ..................................................................... Check
ʘ Main gear spring spar attachment............................................................ Check
Main gear spring spar .........................................................................No cracks
Rotor flight control and damper attachments........No excessive play and secure
ʘ Teeter bolt (bolt end) ....................................................................... Free to turn
Teeter bolt (nut end) ............................................................. Cotter pin installed
Station 10 (passenger station, LH side)

Aft canopy hinge..................................................................................... Secure
Station 11 (pilot station, LH side)

Forward canopy hinge ............................................................................ Secure
Canopy sliding window and frame .......................................... Check, no cracks
Rotor lash bag ................................................................................. As required
4.4 Before Boarding

Fuel level and fuel cap............................................................................. Check
Pneumatic mode selector .............................................. Check BRAKE position
Rotor brake pressure......................................................... Check/set min. 6 bar
Rotor lash bag ................................................................. Removed and stowed
Passenger station:
Passenger ............................................................................Briefed and secure
Aft seat belts......................................................................... Fastened and tight
Loose objects ......................................................................Removed / secured
Storage compartments ......................................................... Closed and locked
Fuel shut off valve ............................................................... Open and guarded
Pilot station:
Loose objects ......................................................................Removed / secured
Storage compartments ......................................................... Closed and locked
4.5 Before Starting Engine

Seat belts ............................................................................................Fastened
Flight controls ............................................................................................. Free
Altimeter .........................................................................Set to airfield elevation
Canopy................................................................................. Closed and locked

4.6 Starting Engine

Parking brake................................................................................................Set
Cold engine:
Throttle ..................................................................................................... Idle
Choke ....................................................................................... Fully engaged
Warm engine:
Throttle ........................................................................ Idle or slightly cracked
Choke ...........................................................................................disengaged
Master switch................................................................................................ON
All engine variants:
Note GEN indicator light ON
Note LOW VOLT flashing briefly
ROTAX 914 engine:
Note BOOST WARN light and BOOST CAUTION light ON for about
2 seconds and buzz of electrical fuel pump.
Second fuel pump P2 (if installed).................................................................ON
All engine variants: Note (increased) fuel pump buzz.
Variable pitch propeller (if installed) ........................................................... FINE
ACL / Strobe (if installed) ..............................................................................ON
Both MAG switches.......................................................................................ON
Propeller and area .................................................................................. “Clear”
Starter (with right hand, left hand on throttle/brake)................................Engage
Hold starter until engine fires, but for a maximum of 10 seconds. Generally
the engine fires immediately. In case of an unsuccessful starting attempt
check all preconditions. Wait at least 20 seconds to allow cooling of battery
and starter motor before repeated activation.
Oil pressure .................................................................................... min. 1.5 bar

Second fuel pump P2 (if installed)............................................................... OFF
Avionics/Radio/Intercom ...............................................................................ON
Choke ..................................................................................... slowly disengage
WARNING
Never attempt to start the engine until the area around the propeller is
completely clear of any persons or objects. Do not start the engine while
standing beside the aircraft as you will easily be struck by the propeller in case
of a brake failure or an operating error.

4.7 Taxi and Run-up

During taxi do not exceed 15 km/h which is approximately jogging speed and steer with
careful pedal input. Use wheel brake carefully, if needed, but not before throttle lever has
been completely pulled to idle. Control stick should always be maintained in forward centre
position. When taxiing on uneven ground, use particular caution and hold control stick so as
to avoid the blades or control system hitting their mechanical stops.
Carry out engine run-up in an area with least derogation to individuals and other airport
ground traffic, preferably headed into the wind.
Warm-up RPM....................................................................... 2000 – 2500 RPM

Oil temperature and other engine indications................................... within limits
At taxi holding position:

Magneto check (at 4000 RPM) ........................................... max. 300 RPM drop
with max. difference between magnetos ...........................................115 RPM
Switch ignition/magnetos with right hand while left hand resides on
throttle/brake.
Throttle .........................................................................................................Idle
Warning and caution indications ................................................................ None
Instruments / altimeter .................................................................... Cross check
NAV lights........................................................................................ As required
Second fuel pump P2 (if installed) ................................................................ ON
Canopy..............................................................Cross-check closed and locked
Approach and runway......................................................... “Clear”, then line-up
4.8 Take-off Procedure

 Check relative wind
 Maintain control stick in forward position with right hand
 Switch pneumatic mode selector to FLIGHT and return to brake with left hand
 Hold wheel brake without having locking pawl engaged
 Release trim pressure by trimming full forward
 While holding wheel brake adjust 1800 RPM with throttle
 Activate and hold pre-rotator
 Let pneumatic clutch fully engage (stabilization at about 110 rotor RPM). There may
be a little throttle required to prevent engine RPM from dropping below 1600 RPM
 Carefully increase throttle (~ 150 R-RPM/sec) to 200 R-RPM – max. 240 R-RPM
 Release pre-rotator button
 Gently move the control stick fully aft (stick travel ~ 1 second)
 Release wheel brake with throttle unchanged
 Monitor rotor speed and adequately increase throttle to take-off power

WARNING
Before activating the pre-rotator, check area is clear.
WARNING
Prior to releasing the wheel brake make sure that the control stick is fully aft. A
take-off run with flat rotor system may have fatal consequences.
WARNING
With the rotor speed below green arc relative speed must be built-up carefully
to allow rotor speed to increase first. If the situation cannot be corrected, abort
take-off run.
CAUTION
Do not engage pre-rotator at too high engine RPM or until too high rotor RPM
as this will lead to pre-rotator drive damage.
CAUTION
Avoid overtorqing of the pre-rotator drive! Overtorqing will occur if RPM/power
is fed excessively or abruptly. In case of a stalling engine, release pre-rotator
button. Do not yank the throttle control while the clutch is engaged!
NOTE
Perform take-off into the wind and with least possible crosswind component.
NOTE
To avoid unintended engagement in flight the pre-rotator can only be activated
with the control stick in its most forward position.

4.9 Take-off Run

 Check min. 5400 RPM for take-off. Otherwise, abort take-off
 Minimize lateral drift by applying appropriate lateral control stick input into cross wind
direction
 Maintain directional control i.e. runway alignment with sensitive pedal input
 When nose comes up allow nose wheel to float at about 10 – 15 cm above the
runway by a balanced reduction of control stick back pressure
 Maintain attitude until speed increases and gyroplane lifts off
 Allow gyroplane to build-up speed in ground effect
VPP: With a variable pitch propeller installed, refer to the respective
flight manual supplement in CHAPTER 9 for correct power setting and
handling procedure.
WARNING
Gyroplanes are fully controllable at very low speeds without exhibiting any
signs of wing stall or soft flight controls, as it would be perceived in a fixed
wing aircraft. However, operation ‘behind the power curve’ may have fatal
consequences during take-off, initial climb or in any other situation within
ground proximity. Always allow aircraft to build-up safe climb speed before
allowing it to gain height.
4.10 Climb
 Perform initial climb at safe climb speed and adjust trim
 Set power to maximum take-off power
 Check engine instruments and respect maximum take-off power time limit
 Switch off second fuel pump at safe height
 At safe altitude, the climb may be continued with V Y and reduced power setting for
noise abatement
 When desired altitude is approached, level gyroplane and reduce power
handling procedure.
4.11 Cruise
 Adjust power setting within the maximum continuous power range
 Adjust trim
handling procedure.

4.12 Descent
 Reduce power setting and lower nose
 Adjust trim
handling procedure.
4.13 Approach
 Switch ON second fuel pump P2 (if installed)
 Set variable pitch propeller (if installed) to FINE
 Check all warning and caution indications OFF
 Check all instruments in normal operating range
 Check wheel brake unlocked
 Maintain and trim approach speed
 Control glide angle with engine power
WARNING
With low fuel level an excessive nose-down attitude, for example in a steep
descent, can lead to premature fuel starvation. An approach within the gliding
distance to the airport or landing site is generally considered to be the safest
option.
4.14 Landing
 Align gyroplane with rudder and correct drift with lateral control input, even if this
results in a side slip indication
 Maintain approach speed until approximately 5m above runway
 Initiate round out to reduce sink rate and let ground approach
 Perform final flare close to ground as speed will decay rapidly
 Let gyroplane settle on main gear with nose wheel slightly above the ground
 Hold nose wheel closely above ground and let it sit down with pedals neutral at the
lowest possible ground speed
 Maintain aft control stick to reduce speed until walking speed. Wheel brake may be
used to assist, if needed
CAUTION
When landing in a strong headwind do not use wheel brake to prevent
gyroplane from rollback. In order to compensate for any rollback tendency,
flatten rotor disc as required and increase propeller thrust, if necessary.

4.15 Go-around
 Apply take-off power. Counteract yaw tendency and align gyroplane with rudder
input.
 In horizontal flight, allow gyroplane to gain speed
 Climb with safe or best rate of climb speed and adjust trim
handling procedure.
4.16 After Landing

 Control stick full forward to level-off rotor disc, at latest when rotor speed leaves
green arc! Be prepared for reduced rotor drag!
 Use lateral control into wind to maintain rotor disc in level attitude. Adjust lateral
control input as rotor speed decays
 Bring pneumatic mode selector to BRAKE position and return to wheel brake with left
hand
 Apply rotor brake pressure by using AFT TRIM. Monitor pressure gauge
 Taxi carefully, preferably not above walking speed and mind high centre of gravity
when taking turns
 Do not vacate gyroplane until engine and rotor is at a complete stop
WARNING
Mind the spinning rotor and propeller when taxiing close to obstructions or
persons. A fast turning rotor is almost invisible, but may contain enough
energy to kill a person.
CAUTION
There are different riskless techniques to park the blades fore and aft. Abrupt
pedal input during taxi should be avoided.
NOTE
It is advisable to let the rotor spin down while the gyroplane is at a complete
stop. However, in order to vacate the runway, it is possible to taxi while the
rotor is spinning down. In this case, be aware of the effects of relative wind on
advancing and retreating blade, compensate with lateral control input, and
adjust taxi speed carefully as to avoid blade flapping.

4.17 Engine Shut-down

Throttle ........................................................................................................ Idle
Parking brake................................................................................................Set
Turbo charger cool-down (ROTAX 914 engine) ....................... min. 30 seconds
Second fuel pump (if installed) .................................................................... OFF
Avionics/Radio/Intercom/Lights (except ACL / Strobe) ................................ OFF
Both MAG switches..................................................................................... OFF
ACL / Strobe (if installed) ............................................................................ OFF
FAN ...................................................................................... activate if required
Master switch.................................................................. OFF and key removed
4.18 Parking
 Install rotor lash bag
 Secure gyroplane against rolling using parking brake and chocks, if parked on a
slope
 Double check to have master switched OFF and keys removed
 Install protection cover if available or appropriate
CAUTION
Especially in strong winds operate canopy with nose pointed into the wind to
eliminate the risk that the canopy is blown open or shut.
NOTE
Avoid long term parking of the aircraft with empty tanks. This will increase the
risk of water accumulation in the tanks and will lead to shrinking of the rubber
tap seal.
4.19 Special Procedure: Short Field Take-off

A short field take off is conducted in exactly the same manner as a normal take-off, but
performed with maximum precision. Therefore, a short field take-off is not so much a
procedural thing, but needs practice, experience and mentoring. Apart from environmental
aspects such as wind and density altitude, the condition of the gyroplane and its gross
weight, the key factors for a short take-off performance are:
 Maximum allowed pre-rotation RPM and no time lost until stick is fully aft and brake is
released
 Maximum take-off power is set immediately while stick remains fully aft until nose
wheel rises
 Nose wheel held tight above surface and minimum side drift until lift-off
 No over controlling that would result in the nose swinging up and down
 VY climb with no side slip

4.20 Special Procedure: Slow Speed Sink and Recovery

 Reduce power to idle and let speed decrease by gently using aft control stick
 Maintain enough forward speed for sufficient rudder effectivity
 Rudder will regain effectivity quickly as soon as airspeed or propeller thrust is
increased
 To recover, let nose drop slightly below the horizon and build-up air speed while
adding power at the same time
4.21 Training Engine In-flight Shut-down and Air Restart

The engine should not be stopped in flight deliberately except as part of forced landing
training under the supervision of a qualified flight instructor. If possible, allow the engine to
cool down at 3000 rpm for about 30 sec before turning it off.
Make sure both magnetos are switched back ON and the master switch/starter key has
been turned to OFF and back to ON to be prepared for an immediate engine start-up in
case the manoeuvre has to be aborted.
NOTE
Be aware of reduced rudder effectivity with standing propeller. Be prepared to
use larger pedal input and more left pedal than usual to keep gyroplane
aligned.
After a restart, allow engine and oil to warm-up, if possible, before full power is applied.
4.22 Noise Abatement

A positive attitude towards residents and environmental-friendly flying supports the
reputation and acceptance of aviation in general, and gyroplanes in particular. When
compared to other airplanes the noise of a gyroplane is sometimes perceived as unpleasant
although it meets the same or sometimes more stringent noise emission requirements. This
effect can be attributed to the pusher concept where the propeller is exposed to air flow
which was distorted by the fuselage. The degree of distortion, and therefore the noise
emission of the propeller, is significantly lower at reduced speeds. The best practices to
keep noise level low and general acceptance high are:
 Climb with the speed for best rate of climb V Y as soon as altitude permits
 Especially in climb keep side slip to a minimum to establish a clean configuration. In
addition, this guarantees the best climb performance
 For your own safety always maintain safe altitude and avoid unnecessary ‘low-flying’
 When overflying populated areas, look ahead and select the least noise sensitive
route
 Repetitive noise is far more irritating than a single occurrence. If you must fly over the
same area more than once, vary your flight path
 Avoid blade slap. Blade slap can occur as a result of inadequate piloting technique or
during aggressive manoeuvres, but will not appear in normal flight regime

NOTE
Above procedures do not apply where they would conflict with Air Traffic
Control, within the traffic pattern, or when, according to pilot’s judgement, they
would result in an unsafe flight path.


Calidus PERFORMANCE
CONTENTS
5.1 Demonstrated Operating Temperature ..........................................................5-1

5.2 Airspeed Calibration ......................................................................................5-1
5.3 Height-Velocity Diagram ................................................................................5-2
5.4 Speeds ..........................................................................................................5-3
5.5 Rate of Climb.................................................................................................5-3
5.6 Take-off and Landing Data ............................................................................5-3
5.7 Influence on Take-off Distance and Climb Rate .............................................5-4
5.8 Glide Ratio ....................................................................................................5-5
5.9 Additional Performance Data .........................................................................5-6
5.9.1 Fuel Flow..................................................................................................5-6
5.9.2 Service Ceiling..........................................................................................5-6
5.10 Sound Exposure Level / Noise Characteristics ..............................................5-6

Calidus PERFORMANCE

Calidus PERFORMANCE
SECTION 5 - PERFORMANCE
The following data were determined by flight testing and demonstrated with average piloting
skills, with engine and aircraft in good condition, as well as clean main rotor and propeller.
The parameters apply to standard conditions (15 °C at sea level and standard pressure)
and a gross mass of 450 kg. Note that a higher airfield elevation, increased temperature
and/and low air pressure will have a negative effect on performance.
5.1 Demonstrated Operating Temperature

Satisfactory engine cooling has been demonstrated to an outside air temperature of 40 °C.
5.2 Airspeed Calibration
Example: Indicated airspeed of 140 km/h represents a calibrated airspeed (corrected for
installation error) of 138 km/h.

Calidus PERFORMANCE
5.3 Height-Velocity Diagram

The H/V diagram indicates combinations of height and speed (avoid area left side of the red
graph) where a safe landing may not be possible in case of an engine failure. Therefore,
operation on the left side of the red line must be avoided.
Take-offs and landings should be conducted according to the recommended flight profile,
provided as blue dashed line.

Calidus PERFORMANCE
5.4 Speeds
The following speeds are relevant for flight performance. For additional speed limitations
refer to SECTION 2 LIMITATIONS of this manual.
Minimum horizontal speed, TOP (only ROTAX 914) .......................40 km/h IAS
Minimum horizontal speed, TOP .....................................................45 km/h IAS
Minimum horizontal speed, MCP.....................................................50 km/h IAS
Speed for best angle of climb V X .....................................................80 km/h IAS
Speed for best rate of climb or maximum endurance V Y ..................90 km/h IAS
Best range speed.......................................................................... 130 km/h IAS
Long range speed*........................................................................ 140 km/h IAS
* Long range speed is the speed faster than the best range speed which
results in a slightly lesser range but represents a good compromise between
range and saved air time.
5.5 Rate of Climb
Rate of climb, 450 kg, V Y, MCP................................................................. 4 m/s

Rate of climb, 360 kg, V Y, MCP................................................................. 6 m/s
5.6 Take-off and Landing Data

Take-offs and landings have been demonstrated up to a crosswind component of 36 km/h.
The following data is valid for operation at a gross mass of 450 kg at an even air strip with
short grass, no wind, and pre-rotation to 220 RPM. Take-off and landing distances account
for a 15m obstacle.
Take-off roll* .................................................................................... 80 – 120 m

Take-off distance* .................................................................................... 300 m
* Take-off roll and take-off distance will be shorter using the boost regime of
the ROTAX 914 engine
Landing roll .......................................................................................... 0 – 20 m

Landing distance...................................................................................... 150 m

Calidus PERFORMANCE
5.7 Influence on Take-off Distance and Climb Rate

All flight performance figures presented in this chapter are based on standard atmospheric
conditions in sea level. Depending on actual temperature and pressure altitude (elevation)
factors on take-off distance and climb rate can be deducted from the following chart.
See next page for example.

Calidus PERFORMANCE
Example:
Given: Outside Air Temperature 28 °C and Pressure Altitude 3500 ft
Result: 88 % increase in take-off distance and climb rate reduced by 53 %
5.8 Glide Ratio

In case of an engine failure, expect a glide ratio of 1:3 which corresponds to a vertical
distance of 900 m or 0.5 nautical miles for each 1000 ft.

Calidus PERFORMANCE
5.9 Additional Performance Data

5.9.1 Fuel Flow
The following fuel flow figures are provided as estimates and do not constitute certified
performance. Exact fuel flow will vary with environmental conditions, cleanliness of propeller
and rotor, piloting technique (minimum side slip), and power setting. For additional
procedures about proper power setting consult SECTION 9 for supplemental data
concerning the variable pitch propeller, if installed.
Fuel flow at 130 km/h IAS........................................................................13 ltr/h
Fuel flow at 160 km/h IAS........................................................................18 ltr/h
5.9.2 Service Ceiling
The service ceiling is based on 450 kg take-off weight, maximum continuous power, and a
residual climb gradient of 0.5 m/s.
ROTAX 912 ULS ...................................................................................10000 ft
ROTAX 914 UL......................................................................................13000 ft
5.10 Sound Exposure Level / Noise Characteristics

The noise certificate was granted according to the German requirements for noise
protection for microlight gyroplanes (“Lärmschutzverordnung für Ultraleichte
Tragschrauber”) stating an overfly noise of 68 dB or less.

Calidus WEIGHT AND BALANCE
CONTENTS
6.1 General .........................................................................................................6-1

6.2 Weight and Balance Record ..........................................................................6-1
6.3 Compliance with Weight and Balance............................................................6-1


SECTION 6 - WEIGHT AND BALANCE
6.1 General
The gyroplane must be operated within the weight and balance limits as specified in
SECTION 2 of this manual. Loading situations outside these limits can result in restricted
flight control and can ultimately lead to degraded safety.
6.2 Weight and Balance Record

An initial weighing report and equipment list showing gyroplane configuration, empty weight
and centre of gravity is delivered with each gyroplane. This data applies to the gyroplane as
delivered from the factory. Any changes in the configuration should be performed by a
qualified maintenance station and documented. After modifications and at regular intervals
a new weighing report and equipment list should be issued.
6.3 Compliance with Weight and Balance

The Calidus gyroplane is designed in such way that compliance with weight and balance is
provided, if
 the gyroplane is loaded within the individual weight limitations for each station as
provided in SECTION 2 of this manual, and
 the certified maximum take-off weight, representing the total sum of pilot, passenger,
baggage, fuel and current empty weight is not exceeded


Calidus SYSTEM DESCRIPTION
CONTENTS
7.1 Introduction....................................................................................................7-1
7.2 Airframe and Undercarriage...........................................................................7-1
7.3 Doors, Windows and Exits.............................................................................7-1
7.4 Fuel System ..................................................................................................7-1
7.5 Pneumatic System.........................................................................................7-3
7.6 Power Plant ...................................................................................................7-4
7.7 Propeller........................................................................................................7-4
7.8 Rotor System.................................................................................................7-4
7.9 Vibration Damping .........................................................................................7-5
7.10 Flight Controls ...............................................................................................7-5
7.11 Electrical System ...........................................................................................7-7
7.12 Lighting System.............................................................................................7-7
7.13 Instrument Panel ...........................................................................................7-7
7.14 Intercom ...................................................................................................... 7-12
7.15 Pitot Static ................................................................................................... 7-12
7.16 Indicators and Sensors ................................................................................ 7-12
7.17 Seats and Seatbelts .................................................................................... 7-12
7.18 Stowage Capacity........................................................................................ 7-12


SECTION 7 - SYSTEM DESCRIPTION
7.1 Introduction
This section contains the description of the gyroplane and its standard systems and
equipment. Optional equipment is described in Chapter 9 of this manual.
7.2 Airframe and Undercarriage

The load carrying structure of the gyroplane consists of a composite monocoque occupant
enclosure, bolted to an inert-gas welded stainless steel tube framework including tower and
aft extension. The composite structure and main frame carries all loads induced by the crew
stations, engine, rotor, undercarriage, stabilizer, and serves as installation platform for
additional equipment.
Stabilizer structure with rudder is made of GRP (or in certain cases CRP) and is bolted to
the aft extension of the main frame. Attachment points for the engine installation are
provided by a steel tube ring mount at the rear of the mast, which also supports the rotor at
its top end.
The landing gear consists of a steerable nose wheel in a steel fork and two main wheels
with hydraulic brake system. Both main wheels are equipped with wheel pants made from
GRP and are mounted to the ends of the spring spar, which is made from GRP. The spar is
designed to absorb even higher than normal landing loads in case of a hard landing or
crash.
7.3 Doors, Windows and Exits

This gyroplane features one large undivided glazed canopy which is hinged at its left hand
side and has a locking mechanism on the right hand side. The locking mechanism can be
operated from the inside and outside by turning the aluminium lever. The canopy is properly
locked when the detent interlocks with the locking pin bushing and the lever is parallel to the
canopy frame. Note that a firm force is needed to ensure the detent interlocks fully in order
to lock the canopy properly.
Two adjustable fresh air vents on the right hand side and one sliding window with pivoting
vent are provided for ventilation. The sliding window can be used as viewing hatch in case
of emergencies and is wide enough to reach through with a hand.
The gyroplane is embarked and disembarked from the right hand side while the canopy is
held open by a restraint strap. In case the canopy cannot be opened, use the emergency
hammer located at the left hand side of the pilot station to break the Plexiglas and evacuate.
7.4 Fuel System

The fuel system consists of one or two tanks, a single filler port, fuel and ventilation lines,
fuel level indication system, and drain. The filler port is located at the left hand side of the
gyroplane. In order to open the filler cap, lift, then turn the flap, and pull out. Reverse to
close cap. The cap is retained to the aircraft via a security cable.
The main tank is installed below the aft seat in the left hand side and has a capacity of 39
litres. Fuel level is indicated by a transparent sight line with markings and also by a fuel
quantity indicator in the cockpit.

As an option an additional tank with a capacity of 36 litres and may be fitted on the right
hand side. In this case a crossover line connects both to ensure equal level. In order to top-
off tanks it is recommended to fill-up slowly and to allow flow levels to balance-out as the
cross-over flow rate is limited.
Both tanks are ventilated by a ventilation line above the tanks into the rear of the mast. Fuel
hoses are made of fabric-reinforced rubber.
As an option, low fuel sensors may be installed. The LOW FUEL warning light is triggered
as soon as 5 litres or less of useable fuel remain in the tank.
The fuel system versions differ with engine model, see schematics below.
Fuel system ROTAX 912:
Fuel system ROTAX 914:

7.5 Pneumatic System

Aircraft trim, rotor brake and activation of the pre-rotator is controlled by a pneumatic
system, consisting of an electrically driven air compressor with dry cartridge, a pressure
gauge in the cockpit, solenoid valves, air lines, pneumatic actuators, and the respective
cockpit controls.
Trim function
Trimming is effected by varying trim pressure in the pneumatic trim actuator which is
installed in parallel with the rotor head tilt for pitch control. Aft or nose-up trimming activates
the electrical compressor and increases trim pressure, causing the actuator to retract, and
tilting the rotor disc aft. Forward trimming opens the pressure relief valve to reduce trim
pressure and allows the rotor disc to flatten, due to the spindle head offset and the
gyroplane’s weight. The actual trim condition is indicated on the trim/brake pressure gauge
in the centre panel of the cockpit.
Lateral/roll trim is available as an option and works accordingly, using a lateral pneumatic
trim cylinder. With this option installed, lateral trim condition is indicated by a LED bar on the
instrument panel.
Rotor brake
With the pneumatic mode selector in BRAKE position the operation of the pneumatic trim
actuator is reversed so that increased pressure causes the actuator to push the rotor head
up (or level) and presses a brake pad against the rotor head disc. In order to increase brake
pressure, move the 4-way trim switch to aft. Note that this action will also push the control
stick forward. At full brake pressure the control stick will be maintained in its full forward
position.
Activation of the pre-rotator
The pre-rotator is activated as long as the respective switch on the control stick head is
depressed provided the following pre-conditions are met:
 pneumatic mode selector set to FLIGHT
 control stick in full forward position
 trim pressure less than 3 bar
 “Canopy” light OFF (if installed)
When activated the pneumatic clutch is activated and engine torque is transmitted through a
90° gearbox and drive to the pinion which is engaged by another small pneumatic actuator
into the geared ring of the rotor head. The drive pinion is sliding on a helical gear to provide
automatic lock-out in case of rotor RPM overrun. In order to allow necessary changes in
length both pre-rotator drive shafts feature a sliding sleeve coupling.
Activation of the pre-rotator in BRAKE position
The pre-rotator can be activated in BRAKE position to park the rotor blades fore-aft for taxi.
To do so, the pre-rotator switch and the overdrive/override switch in the cockpit panel have
to be pressed simultaneously. Avoid prolonged activation of the pre-rotator with rotor brake
engaged.

7.6 Power Plant

Engine
There are two engine variants available, being the ROTAX 912 ULS normally aspirated
reciprocating engine and the ROTAX 914 UL turbo charged version. Both engine types are
4 cylinder, horizontally opposed, 4 stroke engines featuring
 Ram air cooled cylinders
 Dry sump forced lubrication
 Dual breakerless capacitor discharge ignition
 2 constant depression carburettors
 Hydraulic tappets
 Electric starter
 Generator (Alternator)
 Reduction gearbox with integrated shock absorber and overload clutch
The ROTAX 912 ULS engine provides a maximum take-off power of 100 horse power while
the turbo charged version offers a maximum take-off power of 115 horse power. For
technical details refer to the engine manufacturer’s manual.
Oil system
The oil reservoir with dipstick is accessed through a cover on the right hand side of the
fuselage. The cover is held by 3 cam lock fasteners which can be locked or unlocked by a
quarter turn. The type of lubrication system requires a special procedure for accurate oil
level checking and to prevent overfilling, which is described in SECTION 8 of this manual.
Engine cooling
Engine cooling is provided by ram air cooled cylinders and liquid cooled cylinder heads.
Therefore, cylinder head temperature (CHT) indication in the cockpit corresponds to water
temperature. Sufficient cooling air flow is provided by a ram air duct. The water cooling
system comprises of engine driven pump, radiator with thermo-activated electrical blower
fan, expansion tank with radiator cap, overflow bottle, and hoses.
A single, large area radiator is mounted above the engine so that cooling air from the ram
air duct passes through the cooler, is directed around the engine’s cylinders, and finally
escapes through an opening at the lower rear end of the engine cowling. Force cooling is
ensured by an electrically driven ducted fan controlled by a thermo switch. A push button in
the cockpit allows manual activation temporarily which is typically used to avoid possible
heat build-up after shut-down.
For the relevant checking and replenishing procedures, refer to SECTION 8 of this manual
and also the engine manufacturer’s manual.
7.7 Propeller
A three-bladed, fixed pitch propeller with aluminium hub is used as standard version. The
propeller blades are made from composite material with a foam core. As an option a
variable pitch propeller is available which is described in SECTION 9 of this manual.
7.8 Rotor System

The two-bladed, semi-rigid, teetering rotor system comprises high-strength aluminium
extruded rotor blades, a hub bar, and a common teeter hinge assembly.

The rotor blades feature an aerodynamic profile especially suitable for rotorcraft which, in
combination with its relative centre of gravity, provides aerodynamic stability by eliminating
negative blade pitching moments and flutter tendency. The hollow blade profile is sealed at
both ends by plastic blade caps.
The aluminium rotor hub bar is pre-coned to the natural coning angle of the blades and
connects the blades firmly to each side using 6 fitting bolts and a clamping profile. In order
to compensate for asymmetric air flow in forward flight the blades are free to teeter. The
hinge assembly consists of teeter tower, teeter bolt and teeter block.
The teeter bolt runs in a long Teflon coated bushing in the teeter block (main bearing
action), as well as two shorter bushings in the teeter tower (emergency bearing action). The
main bearing action is supported by special grease which is applied through a grease nipple
on top of the teeter block. Servicing is described in SECTION 8 of this manual.
7.9 Vibration Damping

A certain level of vibration is inherent to any 2-bladed rotor system. In order to reduce
vibration levels to a minimum, a vibration decoupling element in the rotor mast isolates rotor
vibration from the fuselage.
7.10 Flight Controls
Rotor head and trim control

Pitch and roll of the gyroplane are controlled by tilting the complete rotor head by means of
the control stick. Control input is transferred via torsion tube and linkage running below the
seats to the base link and from there to the rotor head via push-pull control cables.
The control stick head is ergonomically shaped to Control stick head
fit the pilot’s right hand and features control buttons
for radio transmission (1), a four-way trim function
(2), and activation of the pre-rotator (3).
The trim control works as a classical 4-way beep
switch. Pulling the beep switch back increases aft
trim or nose-up tendency, while pushing the switch
forward reduces back trim pressure, leading to a
nose-down tendency. Roll trim (if installed) is
effected by pushing the trim switch to the
respective side.
Because of a safety circuit, activation of the pre-
rotator is only possible with the pneumatic mode
selector in FLIGHT position and the control stick
fully forward. This prevents inadvertent activation
of the pre-rotator during flight or in BRAKE mode.
The aft stick is held by means of 2 bolts, self-
1 – Radio transmission
locking nuts and a pair of distance washers within
a bracket and must be removed unless the seat is 2 – Trim switch
occupied by a qualified flight instructor. 3 – Pre-rotator

Rudder and front wheel control

The Rudder is connected to the foot pedals with steel cables which are routed horizontally
along the main frame. Both pairs of pedals are interconnected by a linkage. The nose wheel
steering is directly linked to pedal/rudder control input by control rods.
Throttle and brake quadrant

The throttle and brake quadrant with choke is located on the left side of the pilot station.
Throttle control (1) is conventional with IDLE in aft (or pulled) and full throttle in most
forward position. With the ROTAX 914 UL engine the boost range is entered by overcoming
a small resistance to the front. The throttle lever is linked with cable controls to the
carburettors. A mechanical spring applies tension to the control cables and brings the
carburettors to full throttle in case of a cable break. The throttle lever has a pre-set friction
brake which holds the throttle in the selected position.
Choke (3) is used start a cold engine. In Throttle and brake quadrant
order to do so, pull the choke lever fully to
the rear or ON position and be sure to
have the throttle in idle position. After
starting the engine and a short warm-up,
the choke can be slowly disengaged by
moving the lever into its forward or OFF
position.
The hydraulic wheel brake is actuated by
pulling the brake lever (2). A locking pawl
mechanism allows setting for use as
parking brake. In order to release the
parking brake pull the brake lever a little
further to let the spring-loaded locking pawl
disengage, and then release wheel brake.
Do not try to disengage the locking pawl by
pressing the small release lever without
pulling the brake lever at the same time.
Releasing the pawl using the small release
lever only will lead to premature
deterioration of the teeth. If the teeth are
worn the function of the parking brake will 1 – Throttle lever
be compromised! 2 – Brake lever with locking pawl
The throttle and brake quadrant also 3 – Choke control
supports the brake fluid reservoir (4) with 4 – Brake fluid reservoir
screw cap and fluid level minimum and 5 – Primary brake cylinder
maximum markings, as well as the primary
brake cylinder (5).

7.11 Electrical System

The 12V DC electrical system consists of an engine driven electrical generator, a battery,
master switch, indicators, switches, electrical consumers, and cabling. With the ROTAX 914
UL engine an electrical power supply is vital for continued engine operation as this engine
variant solely relies on electrically driven fuel pumps.
Turning the master switch to the ON position closes the battery contact and energizes the
gyroplane’s electrical system. The red LOW VOLT warning light will illuminate briefly as a
functional check. A steady indication, however, warns the pilot that the voltage of the
system has dropped below a safe value. In this case a safety circuit (load shedding relay)
will automatically disable the aircraft lights and the 12V power receptacle.
A red GEN warning light is installed to indicate that the battery is not being charged.
7.12 Lighting System

The aircraft is approved for day VFR operation only. Position lights, landing light and
strobes are available as optional equipment. If installed, refer to SECTION 9 of this manual.
7.13 Instrument Panel

Different instrument panel layouts are available. The basic instrumentation arrangements
include:
 Standard Layout
 Moving Map Landscape
 Moving Map Portrait
 Glass Cockpit
The standard layout includes all instruments necessary for flight but also installation
provisions for additional conventional instrumentation.
The panel layouts Moving Map Landscape or Portrait include all relevant instruments
arranged in a way to accept most off-the-shelf moving map navigation devices in the
respective format. For detailed user information and instructions concerning the different
moving map systems please refer to the manufacturer’s documentation.
NOTE
Any moving map system shall be used for reference only and does not replace
proper flight planning and constant oversight and awareness.
The Glass Cockpit layout is tailored to the integrated flight and navigation suite DYNON
AVIONICS SkyView. In addition to navigational and moving map functions, the system
provides primary flight data and engine/vehicle monitoring. It is of utmost importance to read
and understand the operators manual and to become familiar with the system before
operation. In case of a system failure, a 2 ¼” (47mm) altimeter, air speed indicator and rotor
speed indicator are provided as back-up instrumentation.
Depending on the chosen instrumentation and optional equipment, the depicted panels on
the following pages may vary.

Panel Layout - Standard
1 – VPP control and fuse (if installed) 18 – Altimeter

2 – Pneumatic mode selector 19 – Air speed indicator
3 – Trim/brake pressure gauge 20 – Radio (if installed)
4 – Engine RPM 21 – ATC transponder (if installed)
5 – Manifold pressure gauge (if inst.) 22 – Vertical speed indicator (if installed)
6 – Rotor RPM 23 – 12V power receptacle (if installed)
7 – Canopy warning light 24 – Cooling fan manual activation
8 – Oil pressure 25 – Cabin heat control (if installed)
9 – Fire warning light 26 – GEN, FAN, LOW VOLT warning lights
10 – Oil temperature 27 – BOOST Warn + Caution light (R914)
11 – Compass (card type option) 28 – Avionics master switch
12 – Cylinder head temperature 29 – Switches (2 nd fuel pump and options)
13 – Lateral trim indicator (if installed) 30 – MAG switches
14 – Fuel level indicator 31 – Hour meter
15 – Low fuel warning light (if installed) 32 – Master/starter switch
16 – Intercom/headphone sockets 33 – Rotor bearing temperature indication
17 – Overdrive push button 34 – Fuses

Panel Layout – Moving Map Landscape
1 – VPP control and fuse (if installed) 17 – Installation provisions for MMS
2 – Engine RPM 18 – Radio (if installed)
3 – Pneumatic mode selector 19 – ATC transponder (if installed)
4 – Rotor RPM 20 – Fuel level indicator
5 – Canopy warning light 21 – 12V power receptacle (if installed)
6 – Air speed indicator 22 – Cooling fan manual activation
7 – Lateral trim indicator (if installed) 23 – Cabin heat control (if installed)
8 – Altimeter 24 – GEN, FAN, LOW VOLT warning lights
9 – Fire warning light 25 – BOOST Warn + Caution light (R914)
10 – Oil pressure 26 – Avionics master switch
11 – Trim/brake pressure gauge 27 – Switches (2 nd fuel pump and options)
12 – Oil temperature 28 – MAG switches
13 – Cylinder head temperature 29 – Hour meter
14 – Intercom/headphone sockets 30 – Master/starter switch
15 – Overdrive push button 31 – Rotor bearing temperature indication
16 – VSI 2 ¼” (47mm) (if installed) 32 – Fuses

Panel Layout – Moving Map Portrait (Garmin 695)
1 – 12V power receptacle (if installed) 18 – Pneumatic mode selector

2 – Engine RPM 19 – Trim/brake pressure gauge
3 – Overdrive push button 20 – Radio (if installed)
4 – Rotor RPM 21 – ATC transponder (if installed)
5 – Altimeter 22 – Oil pressure
6 – MMS 23 – Oil temperature
7 – Canopy warning light 24 – Cylinder head temperature
8 – Lateral trim indicator (if installed) 25 – Cabin heat control (if installed)
9 – Fire warning light 26 – GEN, FAN, LOW VOLT warning lights
10 – MMS frame 27 – BOOST Warn + Caution light (R914)
11 – Air speed indicator 28 – Avionics master switch
12 – Manifold pressure gauge (if inst.) 29 – Switches (2 nd fuel pump and options)
13 – Low fuel warning light (if installed) 30 – MAG switches
14 – Fuel level indicator 31 – Hour meter
15 – Cooling fan manual activation 32 – Master/starter switch
16 – Intercom/headphone sockets 33 – Rotor bearing temperature indication
17 – VPP control and fuse (if installed) 34 – Fuses

Panel Layout – Glass Cockpit (DYNON AVIONICS SkyView.)
1 – VPP control and fuse (if installed) 15 – Pneumatic mode selector

2 – Back-up altimeter 16 – Radio (if installed)
3 – Overdrive push button 17 – ATC transponder (if installed)
4 – Canopy warning light 18 – Trim/brake pressure gauge
5 – Fire warning light 19 – Cabin heat control (if installed)
6 – Low fuel warning light (if installed) 20 – GEN, FAN, LOW VOLT warning lights
7 – Integrated display warning light 21 – BOOST Warn + Caution light (R914)
8 – Rotor RPM 22 – Avionics master switch
9 – DYNON Integrated Display 23 – Switches (2 nd fuel pump and options)
10 – Lateral trim indicator (if installed) 24 – MAG switches
11 – Back-up air speed indicator 25 – Hour meter
12 – 12V power receptacle (if installed) 26 – Master/starter switch
13 – Cooling fan manual activation 27 – Rotor bearing temperature indication
14 – Intercom/headphone sockets 28 – Fuses

7.14 Intercom
The standard intercom system features standard headset sockets (TSR Tip Ring Sleeve)
with additional XLR-3 socket for active headset power supply. Sockets are provided in each
station, on the left hand side of the pilots respectively co-pilots seat. The intercom amplifier
and VOX control is integrated in the respective radio. See manufacturer’s manual for
additional information.
7.15 Pitot Static

Total pressure is picked up by a pitot type tube located in the nose section of the fuselage.
The tube is connected to the integrated cockpit instruments by a plastic line. The static
pressure is measured across two ports, one on either side of the fuselage.
7.16 Indicators and Sensors

Rotor speed is measured by a magnetic pick-up, located directly at the geared ring of the
rotor head. Rotor bearing temperature is measured by a temperature sensor which is
battery powered.
Other indicators and sensors have been described in the respective paragraphs. For engine
related indicators and sensors see the engine manufacturer’s manual.
7.17 Seats and Seatbelts

The seats consist of seating surface as an integral part of the monocoque structure and
backrest, upholstered with removable cushions. The cushions consist of a foam core
covered with an easily cleanable, water-repellent fabric.
The forward backrest hinges are positioned by 4 countersunk allen bolts on two seating
rails. To suit to different leg lengths the backrest hinges can be adjusted by removing the
allen bolts and refitting in a different position on the rails.
In addition the backrest can be adjusted by modifying the lengths of the two adjustment
straps. When adjusting make sure that full travel of the aft control stick is not restricted, if
installed. The aft seat has no adjustment.
An adjustable four point harness is fitted for each seat. Make sure that the aft seat belt is
buckled and tight when flying with the aft seat unoccupied.
7.18 Stowage Capacity

Two storage compartments are located below each seat with a maximum capacity of 2.5 kg
each.

Calidus HANDLING / MAINTENANCE
CONTENTS
8.1 Maintenance Obligations ...............................................................................8-1

8.2 General .........................................................................................................8-1
8.3 Ground Handling ...........................................................................................8-2
8.4 Cleaning ........................................................................................................8-2
8.5 Refuelling ......................................................................................................8-2
8.6 Checking of Engine Oil Level.........................................................................8-2
8.7 Checking of Engine Coolant Level .................................................................8-3
8.8 Tire Pressure.................................................................................................8-3
8.9 Lubrication and Greasing...............................................................................8-3
8.10 Replenishing of Fluids ...................................................................................8-4
8.10.1 Engine oil.............................................................................................8-4
8.10.2 Engine coolant .....................................................................................8-4
8.11 Engine Air Filter.............................................................................................8-4
8.12 Propeller........................................................................................................8-4
8.13 Battery...........................................................................................................8-4
8.14 Winter Operation ...........................................................................................8-4
8.15 Removal, Disassembly, Assembly and Installation of the Rotor .....................8-5
8.15.1 Removal of the Rotor System ..............................................................8-5
8.15.2 Disassembly of the Rotor System ........................................................8-6
8.15.3 Assembly of the Rotor System .............................................................8-7
8.15.4 Installation of the Rotor System ...........................................................8-8
8.16 Road Transport .............................................................................................8-8
8.17 Repairs..........................................................................................................8-9


SECTION 8 - HANDLING AND SERVICING

This chapter contains guidelines for correct handling and servicing of the gyroplane, as well
as manufacturer recommendations helping to keep its performance, reliability and value.
8.1 Maintenance Obligations

According to the German law the owner/operator is responsible to ensure that the aircraft is
properly maintained by an authorized facility and continued airworthiness is asserted by a
qualified inspector. The supervision of this process has been delegated by the National
Authority to the DULV (Deutscher Ultraleichtflugverband e.V.).
All airworthiness limitations, inspections and time limits are described in detail in the
maintenance manual. However, for owner/operator’s information the intervals for mandatory
maintenance events are provided as follows:
 25 h: “25 h inspection” (one-time / non-recurrent)
 100 h / 12 months (whatever occurs first): “100 h inspection”
 12 months: Annual airworthiness review (JNP, Jahresnachprüfung)
For engine maintenance and overhaul, refer to the engine manufacturer’s manual.
Special inspections have to be performed by an authorized and qualified maintenance
centre or the manufacturer after operational incidents, which are
 Hard landing
 Bird strike
 Rotor contact with obstacle
 Propeller contact with obstacle or external impact
 Lightning strike
 Encounter of strong gusts with the risk of overstressing
 Rotor overspeed
If any of the above cases apply, mark the aircraft as ‘unserviceable’ and consult the
manufacturer or an authorized maintenance and repair station before further operation.
Apart from these obligatory inspections and maintenance tasks, the owner/operator is
entitled to perform the following preventive and in-between maintenance tasks and checks,
as well as exchange of parts and minor repairs:
8.2 General
Whenever possible, park the gyroplane in a place where it is protected from direct sunlight,
wind and humidity. High humidity, especially in combination with a salt-laden atmosphere
will lead to corrosion. The sunlight’s ultra-violet radiation and the heat impact on the
GRP/CRP components may lead to a degradation of the materials integrity. The
manufacturer will take no responsibility for damage or impaired safety margin due to
improper treatment.

8.3 Ground Handling

Experience shows that aircraft may be exposed to much higher loads when operated on
ground, than when in flight. Such loads caused by rumbling on rough terrain, or bouncing
the aircraft over the hangar threshold may easily exceed the design load in peak.
Use caution when handling the gyroplane on ground. Do not push at the rudder or at the
outer stabilizers. Avoid excessive swing of the rotor blades as repeated bending ultimately
leads to fatigue or damage.
8.4 Cleaning
Care and regular cleaning of engine, propeller, rotor system and fuselage is the basic
foundation for airworthiness and reliability. Therefore, the gyroplane should be cleaned after
every last flight of the day or more often, if environmental conditions dictate.
In order to protect the gyroplane against dirt, dust, bird soil, and sunlight, the aircraft should
be covered with a light plastic tarpaulin or cloth. Openings to the engine, service access
port and airspeed indicator should be closed after the flight (insects, birds etc.).
Contamination can be cleaned with clean water, possibly with mild cleaning additives. To
clean the rotor it is best to soak contamination with a cloth or towel, wipe with soft or micro-
fibre cloth, and rinse thoroughly with water.
CAUTION
Do not use gasoline or solvents as cleaning agents for the windshields, as it
will destroy them irreparably. Do not let windshields sun-dry after washing as
they will stain permanently.
8.5 Refuelling
Have aircraft grounded before refuelling. Be aware that most airfield refuelling equipment is
laid out for larger diameter tank filler necks and high flow rates. To avoid contamination, use
a funnel with strainer and/or filter when refuelling from canisters. In case of two fuel tanks
installed, a crossover line connects both to ensure equal level. In order to top-off tanks it is
recommended to fill-up slowly and to allow flow levels to balance-out as the cross-over flow
rate is limited.
NOTE
Do not fill to the absolute maximum in order to allow for thermal expansion of
the fuel.
8.6 Checking of Engine Oil Level

Before attempting to check the engine oil level double check that both Magnetos are
switched off. The oil level is measured with the aircraft in a level attitude and should be
between the marks on the dipstick.

Open oil tank access cover, remove oil reservoir cap and dipstick. Turn the engine by the
propeller in the correct sense of rotation until you clearly hear the oil gurgle in the tank.
Insert cleaned dipstick for measurement. Fill up oil according to the engine manufacturer’s
specification when required. After completion make sure the dip stick is in place and the
reservoir cap is back on securely. Install access cover.
CAUTION
Never attempt to turn the engine against its sense of rotation as this may lead
to damage.
8.7 Checking of Engine Coolant Level

Between flights, the engine coolant level is checked by verifying the level in the overflow
bottle is within min. and max. markings. The coolant level can be easily seen when looking
at the transparent overflow bottle when the access cover is removed.
For additional details concerning this pre-flight check and a description of the more
comprehensive daily check procedure, refer to the engine manufacturer’s manual.
8.8 Tire Pressure

Main wheels ........................................................................................... 1.6 bar
Nose wheel ............................................................................................ 1.4 bar
8.9 Lubrication and Greasing

Between maintenance intervals the owner/operator is entitled to do the following lubrication
and greasing:
Component Interval Application Type

Teeter bolt 10 hours 2 grams AutoGyro S.WZ05
Pre-rotator drive as required - AutoGyro S.WZ04
coupling sleeves
CAUTION
Any signs of wear on the teeter tower due to movement of the teeter bolt head
indicate a beginning of seizure of the teeter hinge. In most cases the
phenomenon is caused by insufficient greasing.

8.10 Replenishing of Fluids

8.10.1 Engine oil
See engine manufacturer’s manual.
8.10.2 Engine coolant
See engine manufacturer’s manual. Engine cowling must be removed!
8.11 Engine Air Filter

The air intake filters need to be replaced or cleaned according to the manufacturer‘s
recommendation. Depending on environmental conditions, such as dust, sand, or pollution
the recommended rate of maintenance should be increased as required. Engine cowling
must be removed!
8.12 Propeller
Clean regularly as contamination will noticeably decrease its efficiency, resulting in a
negative effect on both aircraft performance and noise emission. Use either pure water or
add mild cleaning additives. Let contamination soak, then remove with a soft cloth or micro
fibre material and rinse with enough water. Check for erosion and damage, especially at the
leading edge and blade tips. Check tight fit at the propeller blade root or any unusual sound
when tapping the blades, in case of a variable pitch propeller. If in doubt or if damage is
obvious, consult the aircraft manufacturer or a qualified maintenance station.
8.13 Battery
The aircraft is fitted with a maintenance-free gel electrolyte battery. Maintenance is
therefore limited to outside soundness, correct attachment, and cleaning. Check integrity of
the battery as leaking fluid contains corrosive sulphuric acid which would lead to extensive
damage when contacting the framework and attachments.
Charge the battery only with a charging device which is suitable for gel electrolyte batteries.
CAUTION
The battery must never be deep discharged, as it will be damaged. If so, it
might need to be replaced.
8.14 Winter Operation

The cooling system for the cylinder heads of the engine is filled with a mixture of anti-freeze
and water, which gives freezing protection down to -20°C. Check protection temperature of
the coolant and add anti-freeze, if necessary.
If temperatures are expected to fall below protection temperature, drain the coolant, and if
required for service, refill with pure antifreeze. As anti-freeze ages, renew the coolant every
two years. Read the engine manual for the manufacturer’s recommendations.

During winter operations the necessary operating temperature for oil and cooling agent may
not be reached. This can be compensated by taping some portion of the coolers. Monitor all
engine temperatures closely after having the coolers taped and modify, if necessary.
When using heated clothing be aware of the electrical power demand in regard to the
generator performance. Do not exceed the generator output value in order not to drain the
battery. A loss of electric power affects avionics and radio communication and can lead to
an engine failure.
Before each flight inspect all control cables for free and easy movement and sufficient
lubrication.
8.15 Removal, Disassembly, Assembly and Installation of the Rotor

In order to transport or park the gyroplane with minimum space requirements, the rotor
system can be removed and disassembled, if needed. In order to do so, a second person is
needed to assist and help to prevent any damage to the gyroplane or the rotor system.
WARNING
The rotor system must be removed and disassembled for road transport. When
handled incorrectly the rotor system can be damaged irreparably. If undetected
this may have catastrophic consequences.
CAUTION
When removing or disassembling make sure to mark all parts so that each and
every component of the rotor system is reassembled and installed in exactly
the same way and orientation. Some rotor blades have loose washers in them
which are required as balance weights. Do not remove or restrain if present!
8.15.1 Removal of the Rotor System
1. Secure the gyroplane on level ground by engaging the parking brake, adjust the rotor
system lengthwise and pump up the rotor brake to its maximum.
2. Remove and discard split pin and unscrew the castellated nut (5). The rotor system
has to be tilted onto the black rotor teeter stop.
3. The teeter bolt (1) has to be extracted by using only the hand, not a hammer. If
needed tilt the rotor blades carefully onto the teeter stop, in order to prevent the bolt
from jamming. Make sure that the rotor stays level in the teeter axis, if not the teeter
bolt will damage the Teflon coated bushes, while being pushed out.
4. A supervised second person has to hold the rotor system in flying direction.
5. Lift the rotor system carefully out of the teeter tower and be aware of the position of
the shim washers (2). Their thicknesses may differ and it is essential that they are
reinstalled on the correct side! They are marked with dots to identify the correct side.
6. Remove the rotor system to one side by letting it rest on your shoulder and take care
not to collide with stabilizer or propeller.

7. The shim washers and the teeter block in the hub are marked on each side with one
or two engraved dots. Directly after the disassembly the shim washers need to be
fixed on their respective side with cable ties.
8. The rotor system must not be placed on a dirty or grainy surface, as the blades can
scratch and damage easily. The best way is to place the rotor blades centrally onto
two stands, supporting the rotor at approximately 2 m distance from the hub.
1 – Teeter bolt 4 – Split pin

2 – Shim washers (2 ea.) 5 – Castellated nut
3 – Outer washer
Handling of the Rotor System

Do not lift or support the rotor system at its blade tips as the bending moment due to the
weight of the hub assembly may overstress the blade roots. If possible, handle with two
persons while holding approximately in the middle of each blade. When supporting the
system use two stands each positioned in about 2 metres distance from the hub.
CAUTION
The assembled rotor system can be damaged irreparably if handled incorrectly.
If the rotor system is lifted in a wrong way, its own weight may overstrain the
material.
8.15.2 Disassembly of the Rotor System
1. To disassemble the rotor system, place it upside down onto a clean surface or stands
to support the rotor at approximately 2 m from the hub.
2. Loosen locknuts (6) on the first blade by counter holding the corresponding bolt head
to prevent it from turning inside the blade holes.

3. Push out all fitting bolts (4) without any force, but use no more than a gentle tapping if
necessary. Tilt the rotor blade up and down to support easy removal of the bolt.
4. Carefully pull the rotor blade out of the hub (1) in radial direction and take off the
clamping profile (2).
5. Repeat step 2 to 4 on second rotor blade.
6. Do not disassemble the rotor hub!
7. Store and transport rotor blades, clamping profile and rotor hub only in air cushion foil
or using other suitable means to prevent bending or surface damage.
1 – Rotor hub 4 – Fitting bolts (6 ea.)

2 – Clamping profile 5 – Washer (12 ea.)
3 – Rotor blade 6 – Lock nuts (6 ea.)
8.15.3 Assembly of the Rotor System
1. The rotor blades, clamping profile and rotor hub are labelled with an engraved serial
number.
2. Insert the first rotor blade carefully into the clamping profile. Make sure that all serial
numbers match.
3. Fit the rotor hub side with the according serial number to clamping profile and blade.
Insert fitting bolts without using force so that the bolt end is on top when the rotor
system is installed. For re-identification and correct installation position the shaft
length is provided in the figure above. Example: 40/12 means shaft length 40mm.
4. Position the washers and the locknut and
hand-tighten all nuts.
5. Torque-tighten nuts with 15 Nm from the
inside to the outside, using a torque
wrench. When doing so, counter-hold bolts
to prevent any damage the hub and blade
holes.
6. Repeat steps 2 to 5 for the second rotor
Position where serial numbers are
blade.
engraved (bottom side)

8.15.4 Installation of the Rotor System
CAUTION
During installation make sure to have each and every part of the rotor system
installed in exactly the same way and orientation as it was before.
1. Secure the gyroplane on level ground by engaging parking brake, adjust the rotor
head or teeter tower corresponding to fore-aft and pressurize the rotor brake up to
maximum.
2. Check correct matching of parts: The rotor hub and the teeter tower are marked with
two dots according to the orientation for installation.
3. Lift the rotor blade with a second briefed person (one person standing aft, one person
standing directly in front of the hub).
4. Approach with the rotor system from the side to the gyroplane and make sure not to
collide with propeller or stabilizer. Insert the rotor system into the hub from above
while standing on a ladder or the rear seat.
5. The second person can let go, as soon as it is resting centrally in the teeter tower on
the teeter stops.
6. Insert teeter bolt by hand in the same orientation as it was before (bolt head should be
at that side of the teeter block which is marked with one dot) while matching the shim
washers with the corresponding installation positions.
7. Check direction of assembly and shim washers: rotor hub, teeter tower and shim
washers are marked on each side either with one or two engraved dots.
8. If the teeter bolt cannot be inserted, tilt the rotor blade along the teeter axis with the
free hand.
9. Install washer and castellated nut. Hand-tighten only and secure with a new split pin.
Use split pins only once. Make sure that the teeter bolt can be turned easily by hand.
8.16 Road Transport

If road transport cannot be avoided, transport with minimum fuel, which reduces airframe
loads and prevents fuel spilling through vent pipes.
Tie-down the fuselage using the following procedure:
Put a wooden block below the lowest point of the keel tube and lash keel tube against
wooden block. The block should be dimensioned so that the main wheels are half
way unloaded
Lash down both main wheels through the rims
Lash down nose wheel through the rim
Furthermore, it is recommended to wrap the gyroplane for road transportation. Especially

the rotor blades need to be packed carefully, as even the smallest damages may force the
replacement of the complete system.

WARNING
The rotor system must be removed and disassembled for road transport. When
handled incorrectly the rotor system can be damaged irreparably. If undetected
this may have catastrophic consequences.
8.17 Repairs
IMPORTANT NOTE
Repairs may only be executed by persons authorized by the manufacturer, and
in strict compliance with maintenance and repair instructions.


Calidus SUPPLEMENTS
SECTION 9 - SUPPLEMENTS
LIST OF SUPPLEMENTS

9-2 Lights
9-4 Fire Indication

Calidus SUPPLEMENTS
AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 9-ii

Flight Manual SECTION 9-1
Calidus Variable Pitch Propeller - IVO
9-1.1 General
A variable pitch propeller (VPP) manufactured by IVO is available as optional equipment to
optimize the propeller efficiency, fuel consumption, and noise in all flight regimes and power
settings. This is achieved by changing the propeller pitch.
9-1.2 Limitations
No change to standard aircraft
9-1.3 Emergency Procedures

Proceed according to generic variable pitch propeller procedure provided in SECTION 3 for
the standard aircraft.
9-1.4 Normal Procedures

9-1.4.1 Set Propeller to FINE
In order to set the propeller to ‘FINE’ for start-up, take-off and approach, use the following
procedure:
 Press the rocker switch in direction FINE (forward or top position) until end position
safety device (circuit breaker) pops out
 Notice pitch change motor buzz (engine off) or increase of engine RPM
 Wait 5 seconds before re-engagement of breaker
9-1.4.2 Adjust Propeller COARSE
 Adjust propeller pitch and throttle to match engine RPM and manifold pressure
according to the power setting table below
CAUTION
When adjusting the propeller do not overtorque (i.e. too high MAP for given
RPM) the engine as this may lead to overloading, reduced life time or possible
damage.
NOTE
As a safety measure, the mechanical end stop in full COARSE position is
chosen to allow a residual climb rate of 1 m/s in standard atmospheric
conditions at sea level with a maximum gross weight of 450 kg.
AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 9-1 - 1

9-1.5 Performance
ROTAX 912 ULS
Power setting Engine RPM MAP Fuel flow [ltr/h]

Max. TOP 5800 27.5 27
Max. MCP 5500 27 26
75% MCP 5000 26 20
65% MCP 4800 26 18
55% MCP 4300 24 14
ROTAX 914 UL
Power setting Engine RPM MAP Fuel flow [ltr/h]

Max. TOP 5800 39 33
Max. MCP 5500 35 26
75% MCP 5000 31 20
65% MCP 4800 29 17.5
55% MCP 4300 28 12.5
MAP limits do not apply at engine speeds above 5100 RPM, marked by a yellow triangle at
the RPM gauge / engine speed indicator.
NOTE
Above data is valid for standard conditions at sea level. Keep in mind that
engine and propeller performance is affected by altitude and temperature. For
detailed information refer to the engine manufacturer’s and propeller
manufacturer’s documentation.
9-1.6 Weight and Balance

9-1.7 System Description

The IVO variable pitch propeller is controlled by a spring-loaded rocker switch labelled FINE
and COARSE. The switch is installed on the left side of the instrument panel An automatic
fuse is located beside the switch, serving as an end position safety device. Propeller pitch
changes continuously as long as the rocker switch is depressed in the respective position.
Note that there is no direct angle-of-incidence control or position feedback, besides the
mechanical end stops.

Activation of the rocker switch closes an electrical circuit which energizes the electrical pitch
control motor inside the propeller hub through brushes running on a collector ring. The
electrical motor drives a mechanical gear which is connected to torsion tubes running inside
the propeller blades. Actual blade feathering motion is achieved by twisting the complete
blade, without having the need for a pitch change bearing.
9-1.8 Handling and Servicing

Refer to the manufacturer’s documentation.


Calidus Lights
9-2 Lights
9-2.1 General
Depending on customer’s configuration the gyroplane can be equipped with optional
 Landing lights
 Navigation /position lights
 Strobe lights
9-2.2 Limitations

9-2.4 Normal Procedures

The lights can be switched on or off by respective switches in the centre panel, labelled
 “Light” for landing light
 “Nav” for navigation/position lights
 “Strobe” for strobe lights
Due to their small silhouette gyroplanes are easily overlooked, especially if approached
directly from behind, such as on approach. It is therefore highly recommended that
navigation and strobe lights are switched on during flight.
9-2.5 Performance
9-2.6 Weight and Balance


Navigation and strobe lights are installed as combined units at the left hand and right hand
side of the fuselage, behind the passenger station. The landing light consists of a pair of
lamps installed in the nose. Note that the conventional lights have a considerably higher
power demand over those with LED technology. In case of generator or battery malfunction
(“Gen” or “Low Volt” indication on) it is even more essential to switch these lights off in order
to preserve electrical power.


Calidus Lights

Calidus GPS/Moving Map Systems
9-3.1 General
Depending on customer’s configuration the gyroplane can be equipped with different
GPS/Moving Map Systems as optional equipment.
NOTE
Any moving map system shall be used for reference only and does not replace
proper flight planning and constant oversight and awareness.
9-3.2 through 9-3.6

No change to standard aircraft.



Calidus GPS/Moving Map Systems

Calidus Engine Fire Indication
9-4 Fire Indication
9-4.1 General
Depending on customer’s configuration the gyroplane can be equipped with an Fire
indicator light to alert the pilot that the engine is on fire.
9-4.2 Limitations

Proceed according to emergency procedure “Smoke and Fire” provided in SECTION 3 for
the standard aircraft.
9-4.4 through 9-4.9


Calidus Engine Fire Indication

Calidus Canopy Indication
9-5.1 General
Depending on customer’s configuration the gyroplane can be equipped with an Canopy
indicator light to alarm the pilot that the canopy is not properly locked.
9-5.2 Limitations

Proceed according to emergency procedure “Canopy Open in Flight” provided in SECTION
3 for the standard aircraft.
9-5.4 through 9-5.6


The Canopy indication is controlled by a proximity switch at the canopy locking handle. If
the canopy is not properly locked the ‘Canopy’ indication will illuminate and the pre-rotator
will be deactivated.

In case of faulty indication or flicker have readjustment performed by an authorized
maintenance centre.

Calidus Canopy Indication

Calidus SAFETY TIPS
CONTENTS
Low-G Avoidance....................................................................................................... 10-1

Side Slip in Gyroplanes.............................................................................................. 10-1
Flying Low on Fuel Is Dangerous ............................................................................... 10-2
Do Not Push the Envelope and Remain Easy On the Controls................................... 10-2
Strobe Lights On – For Your Own and Other’s Safety ................................................ 10-2
Propellers and Rotors Can Be Extremely Dangerous ................................................. 10-2
Power Lines and Cables Are Deadly .......................................................................... 10-2
Loss of Visibility Can Be Fatal.................................................................................... 10-2
Overconfidence Prevails in Accidents ........................................................................ 10-3
Flying Low over Water is Very Hazardous.................................................................. 10-3
Conversion Pilots Constitute High Risk When Flying Gyroplanes............................... 10-3
Beware of Demonstration or Initial Training Flights .................................................... 10-4
Training Off-Field Simulated Engine Failures ............................................................. 10-4
AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 10 - i

Calidus SAFETY TIPS

Calidus SAFETY TIPS
SECTION 10 - SAFETY TIPS
General
This section provides miscellaneous suggestions and guidance to help the pilot operate the
gyroplane more safely.
Low-G Avoidance
Never push the control stick forward to descend or to terminate a pull-up (as you would in
an airplane). This may produce a low-G (near weightless) condition which can result in a
situation with reduced or lost lateral roll control and significant loss of main rotor RPM.
Always reduce power to initiate a descent.
Side Slip in Gyroplanes

Excessive side slip has to be avoided at all means. Side slip can be safely performed up to
the degree which is necessary for proper runway alignment for landing within crosswind
limitations. Excessive side slip starts at a point where de-stabilizing effects of the fuselage
balance out or even supersede the stabilizing effects of the stabilizer. Pilots being new to
gyroplanes, especially those with fixed wing experience may not be aware of these physical
limitations. When exceeding these limitations, be it by imitating ‘professionals’ or applying
habits and control schemes from fixed wing aircraft, the gyroplane may enter an attitude
where it is not recoverable any more. As the pedal control is rather sensitive and alignment
is crucial in high-performing gyroplanes, pilots should develop a feeling for side slip and
‘automatized feet’ in order to maintain aerodynamic alignment and to compensate for
power-induced yaw couplings by anticipation as a conditioned reflex.
A note to training facilities and flight instructors : Due to their reduced directional
stability, gyroplanes require active control to enter, stabilize and neutralize side slip. Most
students perceive natural discomfort in side slip. Depending on the situation, students may
erroneously make a wrong control input or freeze, especially when overchallanged,
stressed, or surprised by the situation. In our opinion flight training should focus on the
necessity of correct alignment, the training of recovery procedures, and the development of
the right reflexes. Intentional side slip training as a normal procedure is considered to be
critical as there is no instrument to indicate ‘safe’ boundaries. An experienced pilot may tell
from an imminent change in control response when limits are approached. A student,
however, may unknowingly or inadvertently overshoot the limits, especially when he is
overly focussed on the touch-down zone and coming in too high.
Side slip may be performed as a part of the emergency training only, and within safe
boundaries. The student must be briefed
 to use gentle pedal input for initiation and stabilization
 initiate side slip at or below 90 km/h and maintain air speed by using his perception of
speed, respectively speed sensation (for want of a working air speed indication)
 not to rely on airspeed indication in side slip
 never to perform abrupt control stick input into the direction of motion (to chase a
faulty speed indication)
It is highly advisable that the instructor remains light on the controls at all times.

Calidus SAFETY TIPS
Flying Low on Fuel Is Dangerous

Never intentionally allow the fuel level to become critically low. Although a gyroplane leaves
much more options than a fixed wing aircraft and is easier to control during power-off than a
helicopter, a forced landing into unknown terrain always poses unnecessary and
unpredictable risk with danger to material, health, or life.
Do Not Push the Envelope and Remain Easy On the Controls

Avoid abrupt control inputs or accelerated manoeuvres, particularly at high speed. These
produce high fatigue loads in the dynamic components and could cause a premature and
catastrophic failure of a critical component.
Strobe Lights On – For Your Own and Other’s Safety

Turn the strobe lights (if installed) on before starting the engine and leave it on until the rotor
stops turning. The strobe lights are located near the propeller and provide a warning to
ground personnel. Leaving them on in flight is also advisable since the gyroplane may be
difficult for other aircraft to see.
Propellers and Rotors Can Be Extremely Dangerous

Never attempt to start the engine until the area around the propeller is completely clear of
any persons or objects. Do not start the engine while standing beside the aircraft as you will
easily be struck by the propeller in case of a brake failure or an operating error.
Be sure ground personnel or onlookers don't walk into the propeller or main rotor. Mind the
spinning rotor and propeller when taxiing close to obstructions or persons. It is advisable to
maintain at least one rotor diameter distance from obstructions or persons when taxiing with
spinning rotor. A fast turning rotor is almost invisible, but may contain enough energy to kill
a person.
Never let go of the control stick and make sure the rotor blades spin down in level/horizontal
attitude until the rotor is at a complete stop. Wind or negligent behaviour on the control stick
may cause the blades to flap dangerously low and hit control stops, stabilizer, or people.
Power Lines and Cables Are Deadly

Flying into wires, cables, and other objects is by far the number one cause of fatal accidents
in rotary wing aircraft. Pilots must constantly be on the alert for this very real hazard.
 Watch for the towers; you will not see the wires in time
 Fly directly over the towers when crossing power lines
 Allow for the smaller, usually invisible, grounding wire(s) which are well above the
larger more visible wires
 Constantly scan the higher terrain on either side of your flight path for towers
 Always maintain at least 500 feet AGL except during take-off and landing. By always
flying above 500 feet AGL
Loss of Visibility Can Be Fatal

Flying a gyroplane in obscured visibility due to fog, snow, low ceiling, or even a dark night
can be fatal. Gyroplanes have less inherent stability and much faster roll and pitch rates
than airplanes. Loss of the pilot's outside visual references, even for a moment, can result in
disorientation, wrong control inputs, and an uncontrolled crash. This type of situation is

Calidus SAFETY TIPS
likely to occur when a pilot attempts to fly through a partially obscured area and realizes too
late that he is losing visibility. He loses control of the gyroplane when he attempts a turn to
regain visibility but is unable to complete the turn without visual references.
You must take corrective action before visibility is lost! Remember, a precautionary landing
in a gyroplane will always be safer than a flight with impaired or no visibility.
Overconfidence Prevails in Accidents

A personal trait most often found in pilots having serious accidents is overconfidence. High-
time fixed-wing pilots converting to gyroplanes and private owners are particularly
susceptible. Airplane pilots feel confident and relaxed in the air, but have not yet developed
the control feel, coordination, and sensitivity demanded by a gyroplane. Private owners
must depend on self-discipline, which is sometimes forgotten. When flown properly and
conservatively, gyroplanes are potentially the safest aircraft built. But especially gyroplanes
also allow little tolerance when flown to their limits. Gyroplanes must always be flown
defensively.
Flying Low over Water is Very Hazardous

Accidents repeatedly occur while manoeuvring low over water. Many pilots do not realize
their loss of depth perception when flying over water. Flying over calm glassy water is
particularly dangerous, but even choppy water, with its constantly varying surface, interferes
with normal depth perception and may cause a pilot to misjudge his height above the water.
MAINTAIN SAFETY ALTITUDE At ALL TIMES
Conversion Pilots Constitute High Risk When Flying Gyroplanes

There have been a number of fatal accidents involving experienced pilots who have many
hours in airplanes or helicopters but with only limited experience flying gyroplanes.
The ingrained reactions and habits of an experienced airplane pilot can be deadly when
flying a gyroplane. The airplane pilot may fly the gyroplane well when doing normal
manoeuvres under ordinary conditions when there is time to think about the proper control
response. But when required to react suddenly under unexpected circumstances, he may
revert to his airplane reactions and commit a fatal error. Under those conditions, his hands
and feet move purely by reaction without conscious thought. Those reactions may well be
based on his greater experience, i.e., the reactions developed flying airplanes.
For example, in an airplane his reaction to an engine failure would be to immediately and
considerably go forward with the stick or horn. In a gyroplane, application of inadequate
forward stick could result in a low-G situation or, if the engine failure occurred during initial
climb, a reduction of rotor RPM combined with a high sink rate with the consequence of a
hard landing or impact.
Airplane pilots may also underestimate pedal work. Especially in a gyroplane, pedal control
is most critical as it has the highest rate response with the smallest static and dynamic
damping effect of all other controls. On top of that, power-yaw coupling is much more
predominant than in an airplane. Being used to the high directional stability of an airplane, a
conversion pilot may neglect proper pedal work and, which is much worse, assume side slip
limits at the pedal stop. Very much like helicopters, gyroplanes cannot be flown by control
position or control force, but solely by resulting attitude. That means that the pilot together

Calidus SAFETY TIPS
with his built-in senses and programmed reflexes represents a vital part in the active control
feedback loop.
Helicopter pilots, on the other hand, may underestimate the characteristics of gyroplanes
and the necessity for proper training. The simplicity of design may lead them to the
assumption that gyroplanes are easy to fly throughout the envelope. Even helicopter pilots
that do not ‘look down’ on gyroplanes and take it serious may confuse throttle control (push
for power) with the control sense of a collective pitch (pull for power) in a stress situation.
To develop safe gyroplane reactions, conversion pilots must practice each procedure over
and over again with a competent instructor until hands and feet will always make the right
move without requiring conscious thought. AND, ABOVE ALL, HE MUST NEVER
ABRUPTLY PUSH THE CONTROL STICK FORWARD.
Beware of Demonstration or Initial Training Flights

A disproportionate number of fatal and non-fatal accidents occur during demonstration or
Initial training flights. The accidents occur because individuals other than the pilot are
allowed to manipulate the controls without being properly prepared or indoctrinated.
If a student begins to lose control of the aircraft, an experienced flight instructor can easily
regain control provided the student does not make any large or abrupt control movements.
If, however, the student becomes momentarily confused and makes a sudden large control
input in the wrong direction, even the most experienced instructor may not be able to
recover control. Instructors are usually prepared to handle the situation where the student
loses control and does nothing, but they are seldom prepared for the student who loses
control and does the wrong thing.
Before allowing someone to touch the controls of the aircraft, they must be thoroughly
indoctrinated concerning the sensitivity of the controls in a gyroplane. They must be firmly
instructed to never make a large or sudden movement with the controls. And, the pilot-in-
command must be prepared to instantly grip the controls should the student start to make a
wrong move.
Training Off-Field Simulated Engine Failures

Pilots: Besides legal aspects, never train off-field simulated engine failures on your own!
Instructors: Always check an area for wires or other obstructions before simulating engine
failures. Consider go-around path and the suitability for an actual engine off touch-down.
Cut the throttle smoothly and keep control of engine idle RPM to avoid actual engine
starvation.

Appendix
APPENDIX
LIST OF APPENDICES

Customer Feedback Form
Appendix
Appendix
Appendix
Appendix 1
Use this form to register as (new) operator / owner, in order to receive safety and service
related information concerning your aircraft. The information is stored in a database and
is only used within AutoGyro GmbH for the above purpose.
Without proper and timely registration, the operator will not receive vital information,
which may lead to unsafe flight or an un-airworthy aircraft.
Return this form to:
AutoGyro GmbH
Dornierstraße 14
31137 Hildesheim or email to [email protected] or fax +49 (0) 51 21 / 8 80 56-19
Aircraft Type Aircraft Registration Registered at
Airframe S/N Rotor System S/N Engine S/N
Airframe hours Rotor System hours Engine hours
Previous Owner (if applicable)
Signature and Date

New/current Owner
Email Signature and Date

Below fields are used for AutoGyro internal processing – do not fill in!
Data entered onto database Acknowledgement sent (date) Job completed by
Change of Ownership AutoGyro Form AG-F-REG-V1.A

Appendix 1
Change of Ownership AutoGyro Form AG-F-REG-V1.A

Flight Manual Appendix 2
MT-Series Customer Feedback Form
Customer’s feedback is important to AutoGyro’s Technical Publication team.
This manual and all information herein have been compiled with greatest care and a
maximum level of clarity, safety, and user-friendliness in mind. However, we welcome
any comments, questions or suggestions that help us provide a higher quality of our
documentation, services, and products.
All submitted feedback forms will be processed internally. We are committed to providing
a response within ten working days of receipt.
AutoGyro GmbH
Dornierstraße 14
Document Issue/Version Page / Chapter
Product - specify type, year of manufacturing, and serial number ( if applicable)
Other subject
Your feedback or error reporting - use extra sheets if needed and include a suggestion
for correction or remedial action, if possible
Reported by
Email Date
Investigation completed Action and response Internal reference
Appendix AutoGyro Form AG-F-CFB-V1.A

Flight Manual Appendix 2
MT-Series Customer Feedback Form
Appendix AutoGyro Form AG-F-CFB-V1.A

Appendix 3
This form is supplied to enable the owner/operator to inform (anonymously, if needed)

AutoGyro GmbH of any incident, accident, or other field or service failure that they feel
appropriate. The owner must also, of course, inform the relevant authorities if that is
appropriate, e.g. Air Accident Investigation Branch etc.
Depending on the incident information supplied, a corrective action is investigated and, if

needed, supplied back to the customer(s).
The information is stored in a database and is only used within AutoGyro GmbH for the
above purpose.
AutoGyro GmbH
Dornierstraße 14
Aircraft Type Aircraft Registration Registered at
Airframe S/N Rotor System S/N Engine S/N
Airframe hours Rotor System hours Engine hours
Description of incident (be as precise as possible and use extra sheets if needed)
Incident reported by (information is only stored for further

inquiry and deleted after investigation)
Email Signature and Date

Investigation completed Corrective action Internal reference
Incident Reporting AutoGyro Form AG-F-AIR-V1.A

Appendix 3
Incident Reporting AutoGyro Form AG-F-AIR-V1.A

FlightManual Calidus 2-1 ENG

Uploaded by

Copyright:

Available Formats

FlightManual Calidus 2-1 ENG

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

FlightManual Calidus 2-1 ENG

Uploaded by

Copyright:

Available Formats

Flight and Operation Manual

for Gyroplane Calidus

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Pre-pages 1

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Pre-pages 2

Serial number: ______________________________________________

Type certificate number: ______________________________________________

Aircraft manufacturer and

Distribution partner: ______________________________________________

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Pre-pages 3

Rev. Inserted by Date Signature

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Pre-pages 4

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Index / LOEP 1

3.14 Recovery System / Rotor System.................................................................. 3-7

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Index / LOEP 2

SECTION 7 - SYSTEM DESCRIPTION

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Index / LOEP 3

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Index / LOEP 4

LIST OF EFFECTIVE PAGES

Page(s) Rev. Date Page(s) Rev. Date

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Index / LOEP 5

INTENTIONALLY LEFT BLANK

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 Index / LOEP 6

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-i

INTENTIONALLY LEFT BLANK

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1 - ii

1.3 Performance Data and Operating Procedures

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-1

1.4 Definition of Terms

1.5 Important Note

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-2

1.6 Three-view of the Calidus

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-3

1.8 Technical Data

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-4

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-5

1.12 Unit Conversion

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-6

1.13 Abbreviations and Terminology

ACL Anti-Collision Light

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-7

TOC Table Of Contents

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 1-8

2.1 General .........................................................................................................2-1

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 2-i

INTENTIONALLY LEFT BLANK

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 2 - ii

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 2-1

2.2 Environmental Limitations

2.3 Colour Code for Instrument Markings

AutoGyro_FOM_Calidus Revision 2.1 – Issue Date 01.10.2011 2-2

2.4 Airspeed Limitations and Instrument Markings

Air Speed Marking

VNE Never Exceed Speed Red radial 185 km/h

Yellow arc 130 – 185 km/h

Yellow arc 0 – 30 km/h

2.5 Rotor Speed Limitations and Instrument Markings

Rotor Speed Marking

Rotor speed limit Red radial 610 RPM

Rotor speed caution range Yellow arc 550 – 610 RPM