Scribd
Upload
299 views6 pages

BSC Commands

The document provides instructions for attaching and configuring devices and radio units on a mobile network site. It includes commands for: 1. Attaching devices to the site and checking the site configuration. 2. Getting the transmission group (TG) and attaching timeslots to the TG. 3. Adding and configuring edge radio units for different sectors. 4. Blocking and deblocking parts of the mobile object (MO) like the TG, cell, or radio unit.

Uploaded by

vignan kuruva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
299 views6 pages

BSC Commands

The document provides instructions for attaching and configuring devices and radio units on a mobile network site. It includes commands for: 1. Attaching devices to the site and checking the site configuration. 2. Getting the transmission group (TG) and attaching timeslots to the TG. 3. Adding and configuring edge radio units for different sectors. 4. Blocking and deblocking parts of the mobile object (MO) like the TG, cell, or radio unit.

Uploaded by

vignan kuruva
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 6

FOR DELETING DEVICES

RXAPE:MO=RXOTG-1,DCP=ALL;

TO ATTACH THE DEVICES TO SITE

CHECK FOR DIP STATUS


DTSTP:DIP=HYD001;

GET THE DEVICES


DTDIP:DIP=HYD001;
NTCOP:SNT=ETM2-1;
STDEP:DEV=RBLT2-0&&-31;
EXDAI:DEV=RBLT2-0&&-31;
BLODE:DEV=RBLT2-0&&-31;
RXAPI:MO=RXOTG-1,DCP=1&&31,DEV=RBLT2-1&&-31;
TO CHECK THE SITE CONFIGURATION
RLSLP:CELL=HYD001A;
(TCH SHOULD BE MULTIPLES OF 8 = NUMBER OF TRUs)

TO GET THE TG
RXTCP:MOTY=RXOTG,CELL=HYD001A;

TO ATTACH THE EDGE TIMESLOTS (3) TO TG


RXAPI: MO=RXOTG-1, DEV=RBLT-1&&-3,DCP=1&&3,RES64K;

TO ATTACH THE VOICE TIMESLOTS (28) TO TG


RXAPI: MO=RXOTG-1, DEV=RBLT-4&&-31,DCP=4&&31;

TO CHECK FOR THE ATTACHED DEVICES TO THE SITE


RXAPP:MO=RXOTG-1;

AFTER ATTACHING RELEASE THE SITE


RXMSP:MO=RXOTG-1;
RXESI:MO=RXOTG-1,SUBORD;
RXBLE:MO=RXOTG-1,SUBORD;
RLSTC:CELL=HYD001A,STATE=ACTIVE;
RLSTC:CELL=HYD001B,STATE=ACTIVE;
RLSTC:CELL=HYD001C,STATE=ACTIVE;

TO CLEAR A3 ALARM 2A-47

RXMSC:MO=RXOTG-44,AHOP=OFF;

TO RELEASE DIP LAYER

TPBLE:SDIP=6ETM2,LP=VC12-27;
TRU ADDITION

TO ADD EDGE TRUs IN 0 TIE VALUE FOR A SECTOR


RXMOI:MO=RXOTRX-1-0,TEI=0,SIG=CONC,DCP1=178,DCP2=179&&186;
RXMOI:MO=RXOTX-1-0,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-0,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-0-0&&-7;
RXMOC:MO=RXOTRX-1-0,CELL=HYD001A;
RXMOC:MO=RXOTX-1-0,CELL=HYD001A;
Rxesi:mo=rxotrx-1-0,subord;
Rxble:mo=rxotrx-1-0;

TO ADD EDGE TRUs IN 4 TIE VALUE FOR B SECTOR


RXMOI:MO=RXOTRX-1-4,TEI=4,SIG=CONC,DCP1=214,DCP2=215&&222;
RXMOI:MO=RXOTX-1-4,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-4,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-4-0&&-7;
RXMOC:MO=RXOTRX-1-4,CELL=HYD001B;
RXMOC:MO=RXOTX-1-4,CELL=HYD001B;

TO ADD EDGE TRUs IN 8 TIE VALUE FOR C SECTOR


RXMOI:MO=RXOTRX-1-8,TEI=8,SIG=CONC,DCP1=250,DCP2=251&&258;
RXMOI:MO=RXOTX-1-8,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-8,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-8-0&&-7;
RXMOC:MO=RXOTRX-1-8,CELL=HYD001C;
RXMOC:MO=RXOTX-1-8,CELL=HYD001C;

TO ADD OTHER TRUs FOR A SECTOR


RXMOI:MO=RXOTRX-1-1,TEI=1,SIG=CONC,DCP1=131,DCP2=132&133;
RXMOI:MO=RXOTX-1-1,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-1,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-1-0&&-7;
RXMOC:MO=RXOTRX-1-1,CELL=HYD001A;
RXMOC:MO=RXOTX-1-1,CELL=HYD001A;

RXMOI:MO=RXOTRX-1-2,TEI=2,SIG=CONC,DCP1=134,DCP2=135&136;
RXMOI:MO=RXOTX-1-2,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-2,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-2-0&&-7;
RXMOC:MO=RXOTRX-1-2,CELL=HYD001A;
RXMOC:MO=RXOTX-1-2,CELL=HYD001A;

RXMOI:MO=RXOTRX-1-3,TEI=3,SIG=CONC,DCP1=137,DCP2=138&139;
RXMOI:MO=RXOTX-1-3,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-3,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-3-0&&-7;
RXMOC:MO=RXOTRX-1-3,CELL=HYD001A;
RXMOC:MO=RXOTX-1-3,CELL=HYD001A;

TO ADD OTHER TRUs FOR B SECTOR


RXMOI:MO=RXOTRX-1-5,TEI=5,SIG=CONC,DCP1=143,DCP2=144&145;
RXMOI:MO=RXOTX-1-5,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-5,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-5-0&&-7;
RXMOC:MO=RXOTRX-1-5,CELL=HYD001B;
RXMOC:MO=RXOTX-1-5,CELL=HYD001B;

RXMOI:MO=RXOTRX-1-6,TEI=6,SIG=CONC,DCP1=160,DCP2=161&162;
RXMOI:MO=RXOTX-1-6,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-6,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-6-0&&-7;
RXMOC:MO=RXOTRX-1-6,CELL=HYD001B;
RXMOC:MO=RXOTX-1-6,CELL=HYD001B;

RXMOI:MO=RXOTRX-1-7,TEI=7,SIG=CONC,DCP1=163,DCP2=164&165;
RXMOI:MO=RXOTX-1-3,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-3,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-3-0&&-7;
RXMOC:MO=RXOTRX-1-3,CELL=HYD001B;
RXMOC:MO=RXOTX-1-3,CELL=HYD001B;

TO ADD OTHER TRUs FOR C SECTOR


RXMOI:MO=RXOTRX-1-9,TEI=9,SIG=CONC,DCP1=169,DCP2=170&171;
RXMOI:MO=RXOTX-1-9,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-9,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-9-0&&-7;
RXMOC:MO=RXOTRX-1-9,CELL=HYD001C;
RXMOC:MO=RXOTX-1-9,CELL=HYD001C;

RXMOI:MO=RXOTRX-1-10,TEI=10,SIG=CONC,DCP1=172,DCP2=173&174;
RXMOI:MO=RXOTX-1-10,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-10,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-10-0&&-7;
RXMOC:MO=RXOTRX-1-10,CELL=HYD001C;
RXMOC:MO=RXOTX-1-10,CELL=HYD001C;

RXMOI:MO=RXOTRX-1-11,TEI=11,SIG=CONC,DCP1=175,DCP2=176&177;
RXMOI:MO=RXOTX-1-11,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-1-11,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-1-11-0&&-7;
RXMOC:MO=RXOTRX-1-11,CELL=HYD001C;
RXMOC:MO=RXOTX-1-11,CELL=HYD001C;
BLOCK & DEBLOCK
ANY PART OF THE MO CAN BE GIVEN FOR THIS COMMAND
TG
CF
IS
TF
TRX
TX
RX
TS

CASE 1:
TO BLOCK AND DEBLOCK FULL SITE FROM TG
RXBLI:MO=RXOTG-1,SUBORD,FORCE;
RXESE:MO=RXOTG-1,SUBORD;
RXESI:MO=RXOTG-1,SUBORD;
RXBLE:MO=RXOTG-1,SUBORD;

(WHEN SUBORD IS USED THE SUBORDINATE FUNCTION BELOW THE MO WILL


BE CONSIDERED)

CASE 2:
TO BLOCK AND DEBLOCK FULL SITE FROM CF
RXBLI:MO=RXOCF-1,SUBORD,FORCE;
RXESE:MO=RXOCF-1,SUBORD;
RXESI:MO=RXOCF-1,SUBORD;
RXBLE:MO=RXOCF-1,SUBORD;

CASE 3:
TO BLOCK AND DEBLOCK TRU - 0 TIE VALUE
RXBLI:MO=RXOTRX-1-0,SUBORD,FORCE;
RXESE:MO=RXOTRX-1-0,SUBORD;
RXESI:MO=RXOTRX-1-0,SUBORD;
RXBLE:MO=RXOTRX-1-0,SUBORD;

TO CHECK THE FAULT CODE OF MO


RXMFP:MO=RXOCF-1;

TO CHECK THE STATUS OF MO


RXMSP:MO=RXOCF-1;
DIFFERENT STATES OF THE MO

CASE 1:
DEF MBL - MO IS IN DEFINED STATE WITH MANUALLY BLOCKED CONDITION
TO RELEASE USE THESE COMMANDS:
RXESI:MO=RXOCF-1;
RXBLE:MO=RXOCF-1;

CASE 2:
COM MBL - MO IS MANUALLY BLOCKED CONDITION
TO RELEASE USE THIS COMMAND:
RXBLE:MO=RXOCF-1;

CASE 3:
NOOP - MO IS IN NON OPERATIONAL CONDITION
USE THESE COMMANDS TO TRY BLOCK & DEBLOCK

RXESE: MO=RXOCF-1;
RXESI: MO=RXOCF-1;
RXBLE: MO=RXOCF-1;

rxmfp:MO=RXOrx-153-5;

RXese:MO=RXOTS-153-4-0&&-7;

RXmfp:MO=RXOTS-153-4-0&&-7;

rxmop:mo=rxotrx-63-0&&-11;

rlbdp:cell=kvti01c;
rlbdc:cell=kvti01c,chgr=3,numreqbpc=24;

rxapp:mo=rxotg-64;

RXMOI:MO=RXOTRX-78-10,TEI=10,SIG=CONC,DCP1=172,DCP2=173&174;
RXMOI:MO=RXOTX-78-10,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-78-10,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-78-10-0&&-7;
RXMOC:MO=RXOTRX-78-10,CELL=kvti01C;
RXMOC:MO=RXOTX-78-10,CELL=kvti01C;
rxbli:mo=rxotrx-78-10,subord,force;
rxese:mo=rxotrx-78-10,subord;
rxesi:mo=rxotrx-78-10,subord;
rxble:mo=rxotrx-78-10,subord;

RXMOI:MO=RXOTRX-78-11,TEI=11,SIG=CONC,DCP1=175,DCP2=176&177;
RXMOI:MO=RXOTX-78-11,BAND=GSM900,ANT=ANT,MPWR=47;
RXMOI:MO=RXORX-78-11,BAND=GSM900,ANTA=ANTA,ANTB=ANTB,RXD=AB;
RXMOI:MO=RXOTS-78-11-0&&-7;
RXMOC:MO=RXOTRX-78-11,CELL=kvti01C;
RXMOC:MO=RXOTX-78-11,CELL=kvti01c;
rxbli:mo=rxotrx-78-11,subord,force;
rxese:mo=rxotrx-78-11,subord;
rxesi:mo=rxotrx-78-11,subord;
rxble:mo=rxotrx-78-11,subord;

rxbli:mo=rxotrx-178-4,subord,force;
rxese:mo=rxotrx-178-4,subord;
rxesi:mo=rxotrx-178-4,subord;
rxble:mo=rxotrx-178-4,subord;
rxbli:mo=rxotrx-178-5,subord,force;
rxese:mo=rxotrx-178-5,subord;
rxesi:mo=rxotrx-178-5,subord;
rxble:mo=rxotrx-178-5,subord;

RLSLP:CELL=HYD224A; TO CHECK DEFINED & WORKING TIME SLOTS


RXTCP:MOTY=RXOTG,CELL=HYD224A; TO KNOW THE T.G VALUE
RXMSP:MO=RXOTX-TGVALUE-0&&-11; TO CHECK TX/TG/CF/TRX STATUS
RXMFP:MO=RXOTRX-TGVALUE-FAULTY TRU; TO CHECK TRX STATUS/FAULT CODE/HW DETAILS
RXBLI:MO=RXOTRX-TGVALUE-TRU NO,SUBORD; TO BLOCK TRU
RXBLE:MO=RXOTRX-TGVALUE-TRU NO,SUBORD; TO UNBLOCK TRU
RXMSP:MO=RXOTS-TGVALUE-TRUNO-0&&-11;
RXBLI:MO=RXOTS-TGVALUE-TRU NO-0&&-7,FORCE; TO BLOCK TS
RXBLE:MO=RXOTS-TGVALUE-TRU NO-0&&-7; TO UNBLOCK TS
RXAPP:MO=RXOTG-319; TO CHECK E1 CAPACITY
RLGRP:CELL=CELL NO;
RLCRP:CELL=CELL NO;
RXMOP:MO=RXOTRX-TGNO-TRXNO(0&&-11) TO CHECK SECTOR-WISE TRU NOS.

RXMOC:MO=RXOTRX-TGNO-TRXNO,CELL=REQD CELL; TO DEFINE A TRX IN CORRECT SECTOR


RXESI:MO=RXOTRX-TGNO-TRXNO,SUBORD; TO ACTIVATE A TRU WHICH IS IN DEF/MBL STATE
Dtpnc:dip=old,newdip=;

RXMOP:MO=RXOTF-399; -TO KNOW THE DELAY-NO

You might also like